Kukjin Kim [Sat, 5 Nov 2011 02:08:54 +0000 (11:08 +0900)]
ARM: EXYNOS4: Fix the merge conflict
The mark of conflict should be removed.
This happened at the commit fba9569924e0 ("Merge branch 'next' of
git://git.infradead.org/users/vkoul/slave-dma")
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ I always check the conflict resolution with "git diff" before I add
the result, but I clearly missed that this time, and didn't notice the
second conflict in that file after having fixed the first one.
Oops, my bad. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No one in their right mind would expect statfs() to not work on a
automounter managed mount point. Fix it.
[ I'm not sure about the "no one in their right mind" part. It's not
mounted, and you didn't ask for it to be mounted. But nobody will
really care, and this probably makes it match previous semantics, so..
- Linus ]
Linus Torvalds [Sat, 5 Nov 2011 01:02:25 +0000 (18:02 -0700)]
Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
Linus Torvalds [Sat, 5 Nov 2011 00:22:14 +0000 (17:22 -0700)]
Merge branch 'for-3.2/drivers' of git://git.kernel.dk/linux-block
* 'for-3.2/drivers' of git://git.kernel.dk/linux-block: (30 commits)
virtio-blk: use ida to allocate disk index
hpsa: add small delay when using PCI Power Management to reset for kump
cciss: add small delay when using PCI Power Management to reset for kump
xen/blkback: Fix two races in the handling of barrier requests.
xen/blkback: Check for proper operation.
xen/blkback: Fix the inhibition to map pages when discarding sector ranges.
xen/blkback: Report VBD_WSECT (wr_sect) properly.
xen/blkback: Support 'feature-barrier' aka old-style BARRIER requests.
xen-blkfront: plug device number leak in xlblk_init() error path
xen-blkfront: If no barrier or flush is supported, use invalid operation.
xen-blkback: use kzalloc() in favor of kmalloc()+memset()
xen-blkback: fixed indentation and comments
xen-blkfront: fix a deadlock while handling discard response
xen-blkfront: Handle discard requests.
xen-blkback: Implement discard requests ('feature-discard')
xen-blkfront: add BLKIF_OP_DISCARD and discard request struct
drivers/block/loop.c: remove unnecessary bdev argument from loop_clr_fd()
drivers/block/loop.c: emit uevent on auto release
drivers/block/cpqarray.c: use pci_dev->revision
loop: always allow userspace partitions and optionally support automatic scanning
...
Fic up trivial header file includsion conflict in drivers/block/loop.c
Linus Torvalds [Sat, 5 Nov 2011 00:06:58 +0000 (17:06 -0700)]
Merge branch 'for-3.2/core' of git://git.kernel.dk/linux-block
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
Linus Torvalds [Fri, 4 Nov 2011 19:33:34 +0000 (12:33 -0700)]
Merge branch 'for-linus' of git://github.com/cmetcalf-tilera/linux-tile
* 'for-linus' of git://github.com/cmetcalf-tilera/linux-tile:
arch/tile: factor out <arch/opcode.h> header
arch/tile: add the <arch> headers to the set of installed kernel headers
arch/tile: avoid exporting a symbol no longer used by gcc
arch/tile: avoid ISO namespace pollution with <asm/sigcontext.h>
Linus Torvalds [Fri, 4 Nov 2011 19:14:11 +0000 (12:14 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix panic in RC error flushing logic
IB/iser: DMA unmap TX bufs used for iSCSI/iSER headers
IB/iser: Use separate buffers for the login request/response
IB/mthca: Fix buddy->num_free allocation size
Removed the email for support and fixes for orphaned ip2 driver.
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed the reference of Roman Zippel, last maintainer, of orphaned
HFS filesystem.
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Antonio Ospite [Fri, 4 Nov 2011 18:22:19 +0000 (11:22 -0700)]
Documentation: update CodingStyle use of braces
After commit 38829dc9d7b4 ("Documentation/CodingStyle: flesh out if-else
examples") highlight that if _only_one_ branch of a conditional
statement is a single statement, then braces are to be used on both
branches.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the path to find the source files of the inotify subsystem.
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RC error state flush logic in qib_make_rc_req() could return all
of the acked wqes and potentially have emptied the queue. It would
then unconditionally try return a flush completion via
qib_send_complete() for an invalid wqe, or worse a valid one that is
not queued. The panic results when the completion code tries to
maintain an MR reference count for a NULL MR.
This fix modifies logic to only send one completion per
qib_make_rc_req() call and changing the completion status from
IB_WC_SUCCESS to IB_WC_WR_FLUSH_ERR as the completions progress.
The outer loop will call as many times as necessary to flush the queue.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Thu, 3 Nov 2011 22:21:27 +0000 (00:21 +0200)]
IB/iser: DMA unmap TX bufs used for iSCSI/iSER headers
The current driver never does DMA unmapping on these buffers. Fix that
by adding DMA unmapping to the task cleanup callback, and DMA mapping to
the task init function (drop the headers_initialized micro-optimization).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Thu, 3 Nov 2011 22:19:46 +0000 (00:19 +0200)]
IB/iser: Use separate buffers for the login request/response
The driver counted on the transactional nature of iSCSI login/text
flows and used the same buffer for both the request and the response.
We also went further and did DMA mapping only once, with
DMA_FROM_DEVICE, which violates the DMA mapping API. Fix that by
using different buffers, one for requests and one for responses, and
use the correct DMA mapping direction for each.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Linus Torvalds [Fri, 4 Nov 2011 14:58:25 +0000 (07:58 -0700)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
Linus Torvalds [Fri, 4 Nov 2011 14:53:16 +0000 (07:53 -0700)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627ehf) Add support for the W83627UHG
hwmon: (w83627ehf) Clean up probe function
hwmon: (w83627ehf) Properly report PECI and AMD-SI sensor types
hwmon: Use i2c_smbus_{read,write}_word_swapped
hwmon: (smsc47b397) Fix checkpatch errors
hwmon: (lm90) Make code more readable
hwmon: (lm90) Fix warnings
hwmon: (ibmaem) Avoid repeated memory allocations
hwmon: (ibmaem) Make instance initializations independent
hwmon: (ibmaem) Fix error paths
hwmon: (lm73) Make detection less problematic
hwmon: Avoid building drivers for powerpc that read/write ISA addresses
Linus Torvalds [Fri, 4 Nov 2011 14:51:43 +0000 (07:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: hda/realtek - Skip invalid digital out pins
ALSA: hda/sigmatel - Automatically retrieve digital I/O widgets
ALSA: hda - Remove unused variables
ALSA: hda/realtek - Don't create alt-stream for capture when unnecessary
ALSA: hda - Add support for 92HD65 / 92HD66 family of codecs
ALSA: hda - Disable power-widget control for IDT 92HD83/93 as default
ALSA: hda - Check NO_PRESENCE pincfg default bit
ASoC: Ensure we always delay for WM8962 FLL when starting from SYSCLK
ASoC: Ensure the WM8962 oscillator and PLLs start up disabled
ASoC: Ensure WM8962 PLL registers are reset
ALSA: intel8x0 - Fix inclusion of kvm_para.h
ALSA: hda_hwdep: Fix possible buffer overflow
ASoC: Fix return value of wm5100_gpio_direction_out()
ASoC: WM8904: Set `invert' bit for Capture Switch
ASoC: Leave input audio data bit length settings untouched in wm8711_set_dai_fmt
ASoC: wm8711: Fix wrong mask for setting input audio data bit length select
ALSA: intel8x0: Improve performance in virtual environment
ALSA: hdspm - Enable all firmware ranges for PCI MADI/AES cards
ALSA: hdsp - Correct HDSP_VERSION_BIT constant, thus partly fixing RPM detection
ALSA: hdspm - Fix MADI channel format in the status ioctl
...
Jean Delvare [Fri, 4 Nov 2011 11:00:48 +0000 (12:00 +0100)]
hwmon: (w83627ehf) Add support for the W83627UHG
This is essentially a stripped down version of the W83627DHG. Noticeable
difference is that it is still powered with +5V, as older models, even
though the ADC resolution is 8 mV as newer models have.
Thanks to Ulf Bruman (Saab Group) for doing all the testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:47 +0000 (12:00 +0100)]
hwmon: (w83627ehf) Clean up probe function
The probe function has grown pretty large, I think it's time for some
cleanups, starting with these two simple ones:
* Move temp3/in6 check for the W83667HG later in the function, where
it is done for all other chip types.
* Move temperature register setting to a separate function, to avoid
code duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:47 +0000 (12:00 +0100)]
hwmon: (w83627ehf) Properly report PECI and AMD-SI sensor types
When temperature sources are PECI or AMD-SI agents, it makes no sense
to report their type as diode or thermistor. Instead we must report
their digital nature.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:47 +0000 (12:00 +0100)]
hwmon: Use i2c_smbus_{read,write}_word_swapped
Make use of the new i2c_smbus_{read,write}_word_swapped functions.
This makes the driver code more compact and readable. It also ensures
proper error handling.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Dirk Eibach <eibach@gdsys.de> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:47 +0000 (12:00 +0100)]
hwmon: (lm90) Make code more readable
Clean up the code to make it more readable:
* Remove reg_ and new_ prefixes from variable names, they made the
names longer, causing extra line breaks, while not adding much
value.
* Introduce struct device dev* = &client->dev in two functions, to
avoid repeating client->dev everywhere in these functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:46 +0000 (12:00 +0100)]
hwmon: (lm90) Fix warnings
With some configuration option combinations, we get the following
warnings:
drivers/hwmon/lm90.c: In function 'lm90_detect':
drivers/hwmon/lm90.c:1114: warning: 'chip_id' may be used uninitialized
in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_config1' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_convrate' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_emerg2' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_status2' may be used
uninitialized in this function
We can solve these easily by reading the register values first and
checking for errors later. These errors should be very rare, even in
the case of failed detection, so this change has no impact on
performance. And this makes checkpatch.pl happier.
Jean Delvare [Fri, 4 Nov 2011 11:00:46 +0000 (12:00 +0100)]
hwmon: (ibmaem) Avoid repeated memory allocations
Preallocate a buffer for the response to sensor reads, and reuse it
for each read instead of allocating a new one each time. This should
be faster and should also avoid memory fragmentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:46 +0000 (12:00 +0100)]
hwmon: (ibmaem) Fix error paths
I am under the impression that error paths in functions
aem_init_aem1_inst() and aem_init_aem2_inst() are incorrect. In
several cases, the function returns 0 on error, which I suspect is
not intended. Fix this by properly tracking error codes.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Fri, 4 Nov 2011 11:00:46 +0000 (12:00 +0100)]
hwmon: (lm73) Make detection less problematic
Word reads can cause trouble with some I2C devices, so do as much
detection as we can using only byte reads, and only use a word read in
the end to confirm the positive match. Also properly handle read
errors.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Robert Casanova <robertcasanova@nanometrics.ca>
Dean Nelson [Fri, 4 Nov 2011 11:00:45 +0000 (12:00 +0100)]
hwmon: Avoid building drivers for powerpc that read/write ISA addresses
A modprobe of hwmon drivers that read/write ISA addresses on a powerpc results
in a kernel Oops. These reads/writes are being done via the inb()/in_8() and
outb()/out_8() macros.
Prevent these drivers from being built for powerpc.
Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Linus Torvalds [Fri, 4 Nov 2011 04:07:58 +0000 (21:07 -0700)]
Merge git://git.samba.org/sfrench/cifs-2.6
* git://git.samba.org/sfrench/cifs-2.6:
cifs: Assume passwords are encoded according to iocharset (try #2)
CIFS: Fix the VFS brlock cache usage in posix locking case
[CIFS] Update cifs version to 1.76
CIFS: Remove extra mutex_unlock in cifs_lock_add_if
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
be2net: Add detect UE feature for Lancer
be2net: Prevent CQ full condition for Lancer
be2net: Fix disabling multicast promiscous mode
be2net: Fix endian issue in RX filter command
af_packet: de-inline some helper functions
MAINTAINERS: Add can-gw include to maintained files
net: Add back alignment for size for __alloc_skb
net: add missing bh_unlock_sock() calls
l2tp: fix race in l2tp_recv_dequeue()
ixgbevf: Update release version
ixgbe: DCB, return max for IEEE traffic classes
ixgbe: fix reading of the buffer returned by the firmware
ixgbe: Fix compiler warnings
ixgbe: fix smatch splat due to missing NULL check
ixgbe: fix disabling of Tx laser at probe
ixgbe: Fix link issues caused by a reset while interface is down
igb: Fix for I347AT4 PHY cable length unit detection
e100: make sure vlan support isn't advertised on old adapters
e1000e: demote a debugging WARN to a debug log message
net: fix typo in drivers/net/ethernet/xilinx/ll_temac_main.c
...
If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roland Dreier [Fri, 4 Nov 2011 00:48:25 +0000 (17:48 -0700)]
IB/mthca: Fix buddy->num_free allocation size
The num_free field of mthca_buddy has a type of array of unsigned int
while it was allocated as an array of pointers. On 64-bit platforms
this allocates twice more than required. Fix this by allocating the
correct size for the type.
This is the same bug just fixed in mlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Olof Johansson [Wed, 2 Nov 2011 11:00:49 +0000 (11:00 +0000)]
af_packet: de-inline some helper functions
This popped some compiler errors due to mismatched prototypes. Just
remove most manual inlines, the compiler should be able to figure out
what makes sense to inline and not.
net/packet/af_packet.c:252: warning: 'prb_curr_blk_in_use' declared inline after being called
net/packet/af_packet.c:252: warning: previous declaration of 'prb_curr_blk_in_use' was here
net/packet/af_packet.c:258: warning: 'prb_queue_frozen' declared inline after being called
net/packet/af_packet.c:258: warning: previous declaration of 'prb_queue_frozen' was here
net/packet/af_packet.c:248: warning: 'packet_previous_frame' declared inline after being called
net/packet/af_packet.c:248: warning: previous declaration of 'packet_previous_frame' was here
net/packet/af_packet.c:251: warning: 'packet_increment_head' declared inline after being called
net/packet/af_packet.c:251: warning: previous declaration of 'packet_increment_head' was here
Signed-off-by: Olof Johansson <olof@lixom.net> Cc: Chetan Loke <loke.chetan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Wed, 2 Nov 2011 10:55:13 +0000 (10:55 +0000)]
MAINTAINERS: Add can-gw include to maintained files
Commit c1aabdf379bc2feeb0df7057ed5bad96f492133e (can-gw: add netlink based
CAN routing) added a new include file that's neither referenced by any of
the CAN maintainers.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Wed, 2 Nov 2011 13:40:28 +0000 (13:40 +0000)]
net: Add back alignment for size for __alloc_skb
Commit 87fb4b7b533073eeeaed0b6bf7c2328995f6c075 (net: more
accurate skb truesize) changed the alignment of size. This
can cause problems at least on some machines with NFS root:
Problem comes from commit 0e734419
(ipv4: Use inet_csk_route_child_sock() in DCCP and TCP.)
If inet_csk_route_child_sock() returns NULL, we should release socket
lock before freeing it.
Another lock imbalance exists if __inet_inherit_port() returns an error
since commit 093d282321da ( tproxy: fix hash locking issue when using
port redirection in __inet_inherit_port()) a backport is also needed for
>= 2.6.37 kernels.
Reported-by: Simon Kirby <sim@hostway.ca> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Balazs Scheidler <bazsi@balabit.hu> CC: KOVACS Krisztian <hidden@balabit.hu> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Simon Kirby <sim@hostway.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 2 Nov 2011 22:47:44 +0000 (22:47 +0000)]
l2tp: fix race in l2tp_recv_dequeue()
Misha Labjuk reported panics occurring in l2tp_recv_dequeue()
If we release reorder_q.lock, we must not keep a dangling pointer (tmp),
since another thread could manipulate reorder_q.
Instead we must restart the scan at beginning of list.
Reported-by: Misha Labjuk <spiked.yar@gmail.com> Tested-by: Misha Labjuk <spiked.yar@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Metcalf [Thu, 3 Nov 2011 03:02:17 +0000 (23:02 -0400)]
arch/tile: factor out <arch/opcode.h> header
The kernel code was using some <asm> headers that included a mix
of hardware-specific information (typically found in Tilera <arch>
headers) and structures, enums, and function declarations supporting
the disassembly function of the tile-desc.c sources.
This change refactors that code so that a hardware-specific, but
OS- and application-agnostic header, is created: <arch/opcode.h>.
This header is then exported to userspace along with the other
<arch> headers and can be used to build userspace code; in particular,
it is used by glibc as part of implementing the backtrace() function.
The new header, together with a header that specifically describes
the disassembly code (<asm/tile-desc.h> with _32 and _64 variants),
replaces the old <asm/opcode-tile*.h> and <asm/opcode_constants*.h>
headers.
As part of this change, we are also renaming the 32-bit constants
from TILE_xxx to TILEPRO_xxx to better reflect the fact that they
are specific to the TILEPro architecture, and not to TILE-Gx
and any successor "tile" architecture chips.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 3 Nov 2011 02:33:07 +0000 (22:33 -0400)]
arch/tile: add the <arch> headers to the set of installed kernel headers
These headers are similar to the <asm> headers that describe kernel
APIs, but instead describe aspects of the actual hardware in an
OS- and application-independent manner. We need to include them in
the set of installed headers so that userspace tools (including glibc)
can build purely from the provided kernel headers.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 3 Nov 2011 02:23:41 +0000 (22:23 -0400)]
arch/tile: avoid exporting a symbol no longer used by gcc
An earlier Tilera compiler generated calls to an "__ll_mul"
function for long long multiplication. Our libgcc supported that
as an alias for the normal __muldi3 routine, so we made it available
to kernel modules as well. However, for a while now the compiler
has internally been generating only the standard __muldi3 symbol,
and the version we are giving back to the community does not have
the __ll_mul alias, so we are removing it from the kernel too.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 3 Nov 2011 02:19:25 +0000 (22:19 -0400)]
arch/tile: avoid ISO namespace pollution with <asm/sigcontext.h>
<asm/sigcontext.h> is used by glibc's <bits/sigcontext.h> from <signal.h>,
which means that it can't clutter the namespace with random symbols
or #defines. However, we use <arch/abi.h> to get a suitable type to
hold a machine register.
This change makes <arch/abi.h> safe to use in this kind of context
if __need_int_reg_t is defined prior to including the file; in that
case, it only defines a few symbols that are safe in the ISO namespace
(prefixed with double underscores). <asm/sigcontext.h> then uses
the __uint_reg_t type instead of the normal uint_reg_t.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Dan Carpenter [Thu, 13 Oct 2011 05:41:41 +0000 (02:41 -0300)]
[media] cx25821: off by one in cx25821_vidioc_s_input()
If "i" is 2 then when we call cx25821_video_mux() we'd end up going
past the end of the cx25821_boards[dev->board]->input[].
The INPUT() macro obfuscates what's going on in that function so it's
a bit hard to follow. And as Mauro points out the hard coded 2 is
not very helpful.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Paul Bolle [Wed, 12 Oct 2011 20:51:22 +0000 (17:51 -0300)]
[media] media: tea5764: reconcile Kconfig symbol and macro
The Kconfig symbol RADIO_TEA5764_XTAL is unused. The code does use a
RADIO_TEA5764_XTAL macro, but does that rather peculiar. But there seems
to be a way to keep both. (The easiest way out would be to rip out both
the Kconfig symbol and the macro.)
Note there's also a module parameter 'use_xtal' to influence all this.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] omap3isp: preview: Add crop support on the sink pad
The crop rectangle takes the preview engine internal cropping
requirements into account. The smallest allowable margins are 14 columns
and 8 rows when reading from memory, and 18 columns and 8 rows when
processing data on the fly from the CCDC.
The macros that define the minimum/maximum input and output sizes are
defined in seperate files and have no consistent naming. In preparation
for preview engine cropping support, move them all to isppreview.c and
rename them to PREV_{MIN|MAX}_{IN|OUT}_{WIDTH|HEIGHT}*.
Remove unused and/or unneeded local variables that store the maximum
output width.
[media] omap3isp: preview: Remove horizontal averager support
The horizontal averager isn't used and will get in the way when
implementing cropping support on the input pad. Remove it, it can be
added back later if needed.
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
This driver exposes preview mode operation of the S5K6AAFX sensor with
embedded SoC ISP. The native capture (snapshot) operation mode is not
supported.
Following controls are available:
manual/auto exposure and gain, power line frequency (anti-flicker),
saturation, sharpness, brightness, contrast, white balance temperature,
color effects, horizontal/vertical image flip, frame interval,
auto white balance.
RGB component gains are currently exposed through private controls.
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
V4L2_CID_POWER_LINE_FREQUENCY control allows applications to instruct
a driver what is the power line frequency so an appropriate filter
can be used by the device to cancel flicker by compensating the light
intensity ripple. Currently in the menu we have entries for 50 Hz and
60 Hz and for entirely disabling the anti-flicker filter.
However some devices are capable of automatically detecting the
frequency, so add V4L2_CID_POWER_LINE_FREQUENCY_AUTO entry for them.
* with no "retrun ret;" at the end, there is no need to initialize ret
any longer,
* consequently use conditional expressions, not if...else constructs,
throughout ov6650_s_ctrl(),
* v4l2_ctrl_new_std_menu() max value of V4L2_EXPOSURE_MANUAL instead of
equivalent 1 looks more clear.
Created on top of "Converting soc_camera to the control framework"
series.
[media] V4L: replace soc-camera specific soc_mediabus.h with v4l2-mediabus.h
Most users of the <media/soc_mediabus.h> header only need pixel code
definitions, which are now located in the generic <linux/v4l2-mediabus.h>
header. Switch over to reduce soc-camera dependencies.
[media] V4L: soc-camera: make (almost) all client drivers re-usable outside of the framework
The most important change in this patch is direct linking to struct
soc_camera_link via the client->dev.platform_data pointer. This makes most
of the soc-camera client drivers also usable outside of the soc-camera
framework. After this change all what is needed for these drivers to
function are inclusions of soc-camera headers for some convenience macros,
suitably configured platform data, which is anyway always required, and
loaded soc-camera core module for library functions. If desired, these
library functions can be made generic in the future and moved to a more
neutral location.
The only two client drivers, that still depend on soc-camera are:
mt9t031: it uses struct video_device for its PM. Since no hardware is
available, alternative methods cannot be tested.
ov6650: it uses struct soc_camera_device to pass its sense data back to
the bridge driver. A generic v4l2-subdevice approach should be developed
to perform this.
VIDIOC_G_STD can return the current TV-norm to the user in one of two ways:
if an .vidioc_g_std() ioctl operation is provided by the driver, it is
called, otherwise the value ot the .current_norm field of struct
video_device is returned. Since subdevice drivers currently have no access
to struct video_device objects, the only way to provide this information to
the user is by implementing a .g_std() method.
[media] V4L: dynamically allocate video_device nodes in subdevices
Currently only very few drivers actually use video_device nodes, embedded
in struct v4l2_subdev. Allocate these nodes dynamically for those drivers
to save memory for the rest.
If the sh_mobile_csi2 driver didn't attach to a client, normally, because
the respective device connects to the SoC over the parallel CEU interface
and doesn't use the CSI-2 controller, it also shouldn't call
pm_runtime_put() on attempted disconnect.
[media] V4L: mt9m001, mt9v022: use internally cached pixel code
Using the internally cached pixel code, instead of the one, provided by
the soc-camera, removes one more use of struct soc_camera_device in these
drivers. Also remove the no longer needed soc_camera_from_i2c() inline
function.
[media] V4L: soc-camera: start removing struct soc_camera_device from client drivers
Remove most trivial uses of struct soc_camera_device from most client
drivers, abstracting some of them inside inline functions. Next steps
will eliminate remaining uses and modify inline functions to not use
struct soc_camera_device.
[media] V4L: soc-camera: call subdevice .s_power() method, when powering up or down
Currently soc-camera can use power regulators and platform specific
methods to power clients up and down. Additionally, client drivers can
provide their own subdevice .s_power() methods, acting directly on the
device. This patch adds calls to this method, when external power
supplies are on.
[media] V4L: soc_camera_platform: do not leave dangling invalid pointers
The life-time of soc-camera device objects can be longer, than the
time, it is attached to a client driver, therefore all references to
the driver own data have to be cleared, when the driver is detached.
projects / karo-tx-linux.git / log