[POWERPC] mpc5200: Add generic support for simple MPC5200 based boards
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] clarify watchdog operation in documentation
[WATCHDOG] Revert "Stop looking for device as soon as one is found"
Arjan van de Ven [Fri, 18 Jan 2008 21:49:33 +0000 (22:49 +0100)]
x86: add support for the latest Intel processors to Oprofile
The latest Intel processors (the 45nm ones) have a model number of 23
(old ones had 15); they're otherwise compatible on the oprofile side.
This patch adds the new model number to the oprofile code.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Al Viro [Sun, 13 Jan 2008 14:17:35 +0000 (14:17 +0000)]
3c574, 3c515 bitfields abuse
wn3_config is shared by these cards; the way we deal with it is both bad C
(union abuse) and broken on big-endian. For 3c515 it's less serious (ISA
cards are quite rare outside of little-endian boxen), but 3c574 is a pcmcia
one and that'd better be endian-independent... Fix is the same in both
cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
S2io: Fixed synchronization between scheduling of napi with card reset and close
- Fixed synchronization between scheduling of napi with card reset and close
by moving the enabling and disabling of napi to card up and card down
functions respectively instead of open and close.
Jay Cliburn [Tue, 15 Jan 2008 01:56:41 +0000 (19:56 -0600)]
atl1: fix frame length bug
The driver sets up the hardware to accept a frame with max length
equal to MTU + Ethernet header + FCS + VLAN tag, but we neglect to
add the VLAN tag size to the ingress buffer. When a VLAN-tagged
frame arrives, the hardware passes it, but bad things happen
because the buffer is too small. This patch fixes that.
Thanks to David Harris for reporting the bug and testing the fix.
Tested-by: David Harris <david.harris@cpni-inc.com> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some BIOS's break if Wake On Lan is enabled, and the machine
can't boot. Better to have some user's have to call ethtool to
enable WOL than to break a single user's boot.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:25:02 +0000 (16:25 -0800)]
bonding: fix lock ordering for rtnl and bonding_rwsem
Fix the handling of rtnl and the bonding_rwsem to always be acquired
in a consistent order (rtnl, then bonding_rwsem).
The existing code sometimes acquired them in this order, and sometimes
in the opposite order, which opens a window for deadlock between ifenslave
and sysfs.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:25:01 +0000 (16:25 -0800)]
bonding: Fix up parameter parsing
A recent change to add an additional hash policy modified
bond_parse_parm, but it now does not correctly match parameters passed in
via sysfs.
Rewrote bond_parse_parm to handle (a) parameter matches that
are substrings of one another and (b) user input with whitespace (e.g.,
sysfs input often has a trailing newline).
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:25:00 +0000 (16:25 -0800)]
bonding: release slaves when master removed via sysfs
Add a call to bond_release_all in the bonding netdev event
handler for the master. This releases the slaves for the case of, e.g.,
"echo -bond0 > /sys/class/net/bonding_masters", which otherwise will spin
forever waiting for references to be released.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:24:59 +0000 (16:24 -0800)]
bonding: fix locking during alb failover and slave removal
alb_fasten_mac_swap (actually rlb_teach_disabled_mac_on_primary)
requries RTNL and no other locks. This could cause dev_set_promiscuity
and/or dev_set_mac_address to be called with improper locking.
Changed callers to hold only RTNL during calls to alb_fasten_mac_swap
or functions calling it. Updated header comments in affected functions to
reflect proper reality of locking requirements.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:24:58 +0000 (16:24 -0800)]
bonding: fix ASSERT_RTNL that produces spurious warnings
Move an ASSERT_RTNL down to where we should hold only RTNL;
the existing check produces spurious warnings because we hold additional
locks at _bh, tripping a debug warning in spin_lock_mutex().
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:24:57 +0000 (16:24 -0800)]
bonding: fix locking in sysfs primary/active selection
Fix the functions that store the primary and active slave
options via sysfs to hold the correct locks in the correct order.
The bond_change_active_slave and bond_select_active_slave
functions both require rtnl, bond->lock for read and curr_slave_lock for
write_bh, and no other locks. This is so that the lower level
mode-specific functions (notably for balance-alb mode) can release locks
down to just rtnl in order to call, e.g., dev_set_mac_address with the
locks it expects (rtnl only).
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[POWERPC] mpc5200: Add common mpc52xx_setup_pci() routine
This patch moves a generic pci init code from lite5200
platform file to a common mpc52xx_setup_pci() routine
and adds additional compatibility property verification.
Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[POWERPC] mpc5200: Add 'fsl,lpb' bus type for localplus bus
Define MPC52xx specific device id list, add new
'fsl,lpb' compatible id for LocalPlus Bus.
Signed-off-by: Marian Balakowicz <m8@semihalf.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[NIU]: Fix 1G PHY link state handling.
[NET]: Fix TX timeout regression in Intel drivers.
Nigel Cunningham [Thu, 17 Jan 2008 23:21:21 +0000 (15:21 -0800)]
Fix unbalanced helper_lock in kernel/kmod.c
call_usermodehelper_exec() has an exit path that can leave the
helper_lock() call at the top of the routine unbalanced. The attached
patch fixes this issue.
Framebuffer is ok only with default parameters only (it is 1280x800-8@60). If
parameters are video=radeonfb:1280x800-32@60 then xres, yres and xres_virtual
are ok but yres_virtual is 1024. It can be corrected by fbset utility so I
think it can be corrected in the driver code also.
Steps to reproduce: video=radeonfb:1280x800-32@60 or
video=radeonfb:1280x800-16@60
Add 1280x800 mode into modedb
Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carsten Otte [Thu, 17 Jan 2008 23:21:17 +0000 (15:21 -0800)]
#ifdef very expensive debug check in page fault path
This patch puts #ifdef CONFIG_DEBUG_VM around a check in vm_normal_page
that verifies that a pfn is valid. This patch increases performance of the
page fault microbenchmark in lmbench by 13% and overall dbench performance
by 7% on s390x. pfn_valid() is an expensive operation on s390 that needs a
high double digit amount of CPU cycles. Nick Piggin suggested that
pfn_valid() involves an array lookup on systems with sparsemem, and
therefore is an expensive operation there too.
The check looks like a clear debug thing to me, it should never trigger on
regular kernels. And if a pte is created for an invalid pfn, we'll find
out once the memory gets accessed later on anyway. Please consider
inclusion of this patch into mm.
Signed-off-by: Carsten Otte <cotte@de.ibm.com> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ivan Kokshaysky [Thu, 17 Jan 2008 23:21:13 +0000 (15:21 -0800)]
alpha: fix conversion from denormal float to double
The trap handler does properly update the fraction,
but not the exponent...
Thanks to Paolo Bonzini for the bug report and the testcase.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Paolo Bonzini <bonzini@gnu.org> Cc: Richard Henderson <rth@twiddle.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sam Ravnborg [Thu, 17 Jan 2008 23:21:12 +0000 (15:21 -0800)]
mm: fix section mismatch warning in page_alloc.c
With CONFIG_HOTPLUG=n and CONFIG_HOTPLUG_CPU=y we saw
following warning:
WARNING: mm/built-in.o(.text+0x6864): Section mismatch: reference to .init.text: (between 'process_zones' and 'pageset_cpuup_callback')
The culprit was zone_batchsize() which were annotated __devinit but used
from process_zones() which is annotated __cpuinit. zone_batchsize() are
used from another function annotated __meminit so the only valid option is
to drop the annotation of zone_batchsize() so we know it is always valid to
use it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Nilsson [Thu, 17 Jan 2008 23:21:11 +0000 (15:21 -0800)]
CRIS v10: vmlinux.lds.S: ix kernel oops on boot and use common defines
- Move alignment to page size of init data outside ifdef for BLK_DEV_INITRD.
The reservation up to page size of memory after init data was previously
not done if BLK_DEV_INITRD was undefined.
This caused a kernel oops when init memory pages were freed after startup,
data placed in the same page as the last init memory would also be freed
and reused, with disastrous results.
- Use macros for initcalls and .text sections.
- Replace hardcoded page size constant with PAGE_SIZE define.
- Change include/asm-cris/page.h to use the _AC macro to instead
of testing __ASSEMBLY__.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len Brown [Thu, 17 Jan 2008 23:21:10 +0000 (15:21 -0800)]
pnpacpi: print resource shortage message only once (more)
Wups, previous patch was ineffective in 2 cases.
http://bugzilla.kernel.org/show_bug.cgi?id=9535
Signed-off-by: Len Brown <len.brown@intel.com> Reported-by: "Hartkopp, Oliver (K-EFE/E)" <oliver.hartkopp@volkswagen.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Cc: Roman Zippel <zippel@linux-m68k.org> Reported-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Thu, 17 Jan 2008 23:21:08 +0000 (15:21 -0800)]
cpufreq: Initialise default governor before use
When the cpufreq driver starts up at boot time, it calls into the default
governor which might not be initialised yet. This hurts when the
governor's worker function relies on memory that is not yet set up by its
init function.
This migrates all governors from module_init() to fs_initcall() when being
the default, as was already done in cpufreq_performance when it was the
only possible choice. The performance governor is always initialized early
because it might be used as fallback even when not being the default.
Fixes at least one actual oops where ondemand is the default governor and
cpufreq_governor_dbs() uses the uninitialised kondemand_wq work-queue
during boot-time.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Francois Romieu [Thu, 10 Jan 2008 22:53:15 +0000 (23:53 +0100)]
ipg: fix Tx completion irq request
The current logic will only request an ack for the first pending
packet. No irq is triggered as soon as the CPU submits a few
packets a bit quickly. Let's request an irq for every packet
instead.
Francois Romieu [Thu, 10 Jan 2008 22:40:59 +0000 (23:40 +0100)]
ipg: plug Tx completion leak
The Tx skb release could not free more than one skb per call.
Add it to the fact that the xmit handler does not check for
a queue full condition and you have a recipe to leak quickly.
Let's release every pending Tx descriptor which has been given
back to the host CPU by the network controller. The xmit handler
suggests that it is done through the IPG_TFC_TFDDONE bit.
Remove the former "curr" computing: it does not produce anything
usable in its current form.
Andres Salomon [Thu, 17 Jan 2008 17:01:30 +0000 (12:01 -0500)]
Input: psmouse - fix potential memory leak in psmouse_connect()
If we successfully call input_register_device() in psmouse_connect()
but sysfs_create_group() fails, we'll enter the error path without
ever having called input_unregister_device() potentially leaking
memory.
Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Daniel Ritz [Thu, 17 Jan 2008 17:01:18 +0000 (12:01 -0500)]
Input: usbtouchscreen - fix buffer overflow, make more egalax work
Fix a buffer overflow in mutli-packet handling code. The overflow can
only happen with eGalax devices and is even there very unlikely (only
non-report packet are affected any only when truncated after the first
byte).
Also changes the mutli-packet handling code not to drop unknown packets,
but rather just drop one byte. This allows synchronizing on report packets
in the data stream. It's required for some egalax devices to work at all.
Also remove the pointless 'flags' member of the device struct and set the
version number to 0.6, plus some minor cleanups.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Micah Parrish [Thu, 17 Jan 2008 17:01:04 +0000 (12:01 -0500)]
Input: mousedev - handle mice that use absolute coordinates
Devices like the HP Integrated Remote Console Virtual Mouse, which are
standard equipment on all Proliant and Integrity servers, produce
absolute coordinates instead of relative coordinates. This is done to
synchronize the position of the mouse cursor on the client desktop
with the mouse cursor position on the server. Mousedev is not
designed to pass those absolute events directly to X, but it can
translate them into relative movements. It currently does this for
tablet like devices and touchpads. This patch merely tells it to also
include a device with ABS_X, ABS_Y, and mouse buttons in its list of
devices to process input for.
This patch enables the mouse pointer to move when using the remote
console.
As pointed out by Jesse Brandeburg, for three of the drivers edited
above there is breakout logic in the *_clean_tx_irq() code to prevent
running TX reclaim forever. If this occurs, we have to elide NAPI
poll completion or else those TX events will never be serviced.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Jon Tollefson [Thu, 3 Jan 2008 22:59:50 +0000 (09:59 +1100)]
[POWERPC] Add hugepagesz boot-time parameter
This adds the hugepagesz boot-time parameter for ppc64. It lets one
pick the size for huge pages. The choices available are 64K and 16M
when the base page size is 4k. It defaults to 16M (previously the
only only choice) if nothing or an invalid choice is specified.
Tested 64K huge pages successfully with the libhugetlbfs 1.2.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer [Thu, 3 Jan 2008 15:40:47 +0000 (02:40 +1100)]
[POWERPC] #address-cells & #size-cells properties are not inherited
Fix error in booting-without-of.txt that indicates that a node can inherit
its #address-cells and #size-cells definitions from its parent's parent.
This is not correct.
Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] therm_adt746x: Eliminate some build warnings
We don't care if the device_create_file calls fail, the driver will work
just as well without them, so just issue a runtime warning.
drivers/macintosh/therm_adt746x.c: In function 'thermostat_init':
drivers/macintosh/therm_adt746x.c:615: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:616: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:617: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:618: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:619: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:620: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:621: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:622: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:623: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_adt746x.c:625: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] therm_windtunnel: Eliminate some build warnings
We don't care if the device_create_file calls fail, the driver will work
just as well without them, so just issue a runtime warning.
drivers/macintosh/therm_windtunnel.c: In function 'setup_hardware':
drivers/macintosh/therm_windtunnel.c:268: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_windtunnel.c:269: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] therm_pm72: Suppress some compile warnings
We don't really care if any of these calls to device_create_file fails,
so just issue warnings in that case.
drivers/macintosh/therm_pm72.c: In function 'init_cpu_state':
drivers/macintosh/therm_pm72.c:1185: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1186: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1187: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1188: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1189: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1191: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1192: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1193: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1194: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1195: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c: In function 'init_backside_state':
drivers/macintosh/therm_pm72.c:1383: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1384: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c: In function 'init_drives_state':
drivers/macintosh/therm_pm72.c:1503: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1504: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c: In function 'init_dimms_state':
drivers/macintosh/therm_pm72.c:1625: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c: In function 'init_slots_state':
drivers/macintosh/therm_pm72.c:1743: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/therm_pm72.c:1744: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jochen Friedrich [Mon, 31 Dec 2007 16:14:53 +0000 (03:14 +1100)]
[POWERPC] Update .gitignore files
Update .gitignore as needed by dtc addition.
Signed-off-by: Jochen Friedrich <jochen@scram.de> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Fri, 21 Dec 2007 04:50:09 +0000 (15:50 +1100)]
[POWERPC] iSeries: eliminate pci_dn bussubno
xlate_iomm_address() really wants the ds_addr to pass to the HV, so store
that value (instead of the BAR number) when we allocate the device bars.
This is not a fast path, so we can look up the device_node property
there instead of using the bussubno field of the pci_dn.
The other user of iseries_ds_addr() was already scanning the device tree,
so looking up a property will not slow it down any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Grant Likely [Tue, 8 Jan 2008 19:20:40 +0000 (06:20 +1100)]
[POWERPC] Add of_find_matching_node() helper function
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
Ralph Campbell [Tue, 15 Jan 2008 23:58:13 +0000 (15:58 -0800)]
IB/ipath: Fix receiving UD messages with immediate data
This fixes a small bug in ipath_ud_rcv()'s handling of UD messages
with immediate data. We need to test whether immediate data is
present and update the header size accordingly *before* testing the
packet size from the header against the actual received length.
Otherwise the wrong header size will be used and all messages with
immediate data will be dropped.
This bug keeps MVAPICH-UD and HP MPI from working at all on ipath devices.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Wed, 16 Jan 2008 17:55:49 +0000 (09:55 -0800)]
Merge branch 'v2.6.24-rc7-lockdep' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep
* 'v2.6.24-rc7-lockdep' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep:
lockdep: more hardirq annotations for notify_die()
lockdep: fix workqueue creation API lockdep interaction
lockdep: fix internal double unlock during self-test
Tejun Heo [Wed, 16 Jan 2008 03:06:14 +0000 (12:06 +0900)]
sysfs: make sysfs_lookup() return ERR_PTR(-ENOENT) on failed lookup
sysfs tries to keep dcache a strict subset of sysfs_dirent tree by
shooting down dentries when a node is removed, that is, no negative
dentry for sysfs. However, the lookup function returned NULL and thus
created negative dentries when the target node didn't exist.
Make sysfs_lookup() return ERR_PTR(-ENOENT) on lookup failure. This
fixes the NULL dereference bug in sysfs_get_dentry() discovered by
bluetooth rfcomm device moving around.
Ivo van Doorn [Fri, 11 Jan 2008 19:53:07 +0000 (20:53 +0100)]
rt2x00: Fix ieee80211 payload alignment
As Johannes Berg indicated, the NET_IP_ALIGN doesn't
need to be used for ieee80211 frames. This means we
can simplify the alignment calculation to just
use the result of the header size modulus 4 as frame
alignment.
Furthermore we shouldn't use NET_IP_ALIGN in rt2x00usb
because it could be 0 on some architectures and we absolutely
need to have 2 bytes reserved for possible aligning.
Signed-off-by: Ivo van Doorn<IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stefano Brivio [Sun, 13 Jan 2008 17:30:14 +0000 (18:30 +0100)]
b43: fix use-after-free rfkill bug
Fix rfkill code which caused a use-after-free bug.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Thu, 10 Jan 2008 22:31:30 +0000 (14:31 -0800)]
hostap: section mismatch warning
Fix section mismatch by changing variable name to match one of the
whitelisted (allowable) names for pointing into init data:
WARNING: vmlinux.o(.data+0xce618): Section mismatch: reference to .init.data:prism2_plx_id_table (between 'prism2_plx_drv_id' and 'dev_info')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / mv-sheeva.git / log