There may be tx-skbs still pending in HW when PHY link down.
Reset MAC will make the DMA engine go to the start point.
and release all pending skbs.
Note: Reset MAC will clear any interrupt status and mask.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware incorrectly process L0S/L1 entrance if the chipset/root
response after specific/shorter timer and cause system hang.
Enlarge the timeout value to avoid this issue.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On some platform with EEPROM/OTP existing, the BIOS could overwrite
a new MAC address for the NIC. so, the permanent mac address should
be from BIOS. the address is restored when driver removing.
Voltage raising isn't applicable for l1d.
Replace swab32 with htonl for big/little endian platform.
related Registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c: add workaround for issue of bit INTX-disable for MSI interrupt
All supported devices have one issue that msi interrupt doesn't assert
if pci command register bit (PCI_COMMAND_INTX_DISABLE) is set.
Add workaround in drivers/pci/quirks.c
Signed-off-by: xiong <xiong@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 27 Apr 2012 21:39:21 +0000 (21:39 +0000)]
bnx2x: remove some bloat
Before doing skb->head_frag work on bnx2x driver, I found too much stuff
was inlined in bnx2x/bnx2x_cmn.h for no good reason and made my work not
very easy.
Move some big functions out of this include file to the respective .c
file.
A lot of inline keywords are not needed at all in this huge driver.
text data bss dec hex filename
490083 1270 56 491409 77f91 bnx2x/bnx2x.ko.before
484206 1270 56 485532 7689c bnx2x/bnx2x.ko
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe: reprogram multicast address register on reset
The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.
The commit eefc48b ("pch_gbe: reprogram multicast address register on
reset") tried to fix this problem, but it introduces unnecessary
codes. In fact, all multicast addresses have been saved in netdev->mc,
So we can call pch_gbe_set_multi() directly after reset_hw and
reset_rx.
This commit kills 50+ line codes
Cc: Richard Cochran <richardcochran@gmail.com> Cc: Takahiro Shimizu <tshimizu818@gmail.com> Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 27 Apr 2012 02:10:03 +0000 (02:10 +0000)]
net: makes skb_splice_bits() aware of skb->head_frag
__skb_splice_bits() can check if skb to be spliced has its skb->head
mapped to a page fragment, instead of a kmalloc() area.
If so we can avoid a copy of the skb head and get a reference on
underlying page.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 27 Apr 2012 00:38:33 +0000 (00:38 +0000)]
tcp: makes tcp_try_coalesce aware of skb->head_frag
TCP coalesce can check if skb to be merged has its skb->head mapped to a
page fragment, instead of a kmalloc() area.
We had to disable coalescing in this case, for performance reasons.
We 'upgrade' skb->head as a fragment in itself.
This reduces number of cache misses when user makes its copies, since a
less sk_buff are fetched.
This makes receive and ofo queues shorter and thus reduce cache line
misses in TCP stack.
This is a followup of patch "net: allow skb->head to be a page fragment"
Tested with tg3 nic, with GRO on or off. We can see "TCPRcvCoalesce"
counter being incremented.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Apr 2012 08:10:34 +0000 (08:10 +0000)]
net: make GRO aware of skb->head_frag
GRO can check if skb to be merged has its skb->head mapped to a page
fragment, instead of a kmalloc() area.
We 'upgrade' skb->head as a fragment in itself
This avoids the frag_list fallback, and permits to build true GRO skb
(one sk_buff and up to 16 fragments), using less memory.
This reduces number of cache misses when user makes its copy, since a
single sk_buff is fetched.
This is a followup of patch "net: allow skb->head to be a page fragment"
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 27 Apr 2012 00:34:49 +0000 (00:34 +0000)]
tg3: provide frags as skb head
This patch converts tg3 driver, one of our reference drivers, to use new
build_skb() api in frag mode.
Instead of using kmalloc() to allocate the memory block that will be
used by build_skb() as skb->head, we use a page fragment.
This is a followup of patch "net: allow skb->head to be a page fragment"
This allows GRO, TCP coalescing, and splice() to be more efficient.
Incidentally, this also removes SLUB slow path contention in kfree()
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 27 Apr 2012 00:33:38 +0000 (00:33 +0000)]
net: allow skb->head to be a page fragment
skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.
We have three spots were it hurts :
1) GRO aggregation
When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.
2) splice(socket -> pipe).
We must copy the linear part to a page fragment.
This kind of defeats splice() purpose (zero copy claim)
3) TCP coalescing.
Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)
Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.
build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.
Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.
This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Maciej Żenczykowski <maze@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 27 Apr 2012 09:04:06 +0000 (09:04 +0000)]
bnx2x: add transmit timestamping support
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Mon, 30 Apr 2012 19:29:02 +0000 (15:29 -0400)]
tipc: compress out gratuitous extra carriage returns
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Herbert Xu [Mon, 30 Apr 2012 00:22:56 +0000 (00:22 +0000)]
bridge: Fix fatal typo in setup of multicast_querier_expired
Unfortunately it seems that I didn't properly test the case of
an expired external querier in the recent multicast bridge series.
The setup of the timer in that case is completely broken and leads
to a NULL-pointer dereference. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Fri, 27 Apr 2012 08:24:18 +0000 (08:24 +0000)]
net/l2tp: add support for L2TP over IPv6 UDP
Now that encap_rcv() works on IPv6 UDP sockets, wire L2TP up to IPv6.
Support has been tested with and without hardware offloading. This
version fixes the L2TP over localhost issue with incorrect checksums
being reported.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Fri, 27 Apr 2012 08:23:59 +0000 (08:23 +0000)]
net/ipv6/udp: UDP encapsulation: move socket locking into udpv6_queue_rcv_skb()
In order to make sure that when the encap_rcv() hook is introduced it is
not called with the socket lock held, move socket locking from callers into
udpv6_queue_rcv_skb(), matching what happens in IPv4.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Fri, 27 Apr 2012 08:23:21 +0000 (08:23 +0000)]
net/ipv6/udp: UDP encapsulation: break backlog_rcv into __udpv6_queue_rcv_skb
This is the first step in reworking the IPv6 UDP code to be structured more
like the IPv4 UDP code. This patch creates __udpv6_queue_rcv_skb() with
the equivalent sematics to __udp_queue_rcv_skb(), and wires it up to the
backlog_rcv method.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/oki-semi: Remove the definition of PCH_GBE_ETH_ALEN
PCH_GBE_ETH_ALEN is equal to ETH_ALEN, so we can replace it with
ETH_ALEN.
If they are not equal, it must be a bug, since this is ethernet,
and the address has been already stored to mc_addr_list as ETH_ALEN
bytes when call pch_gbe_mac_mc_addr_list_update.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Thu, 26 Apr 2012 00:30:43 +0000 (00:30 +0000)]
net/at91_ether: use gpio_to_irq for phy IRQ line
Use the gpio_to_irq() function to retrieve the phy IRQ line
from the GPIO pin specification.
This fix is needed now that we have moved to irqdomains on AT91.
Reported-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Victor [Thu, 26 Apr 2012 00:30:42 +0000 (00:30 +0000)]
AT91: Remove fixed mapping for AT91RM9200 ethernet
The AT91RM9200 Ethernet controller still has a fixed IO mapping.
So:
* Remove the fixed IO mapping and AT91_VA_BASE_EMAC definition.
* Pass the physical base-address via platform-resources to the driver.
* Convert at91_ether.c driver to perform an ioremap().
* Ethernet PHY detection needs to be performed during the driver
initialization process, it can no longer be done first.
Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 26 Apr 2012 22:13:08 +0000 (18:13 -0400)]
tipc: Reject payload messages with invalid message type
Adds check to ensure TIPC sockets reject incoming payload messages
that have an unrecognized message type.
Remove the old open question about whether TIPC_ERR_NO_PORT is
the proper return value. It is appropriate here since there are
valid instances where another node can make use of the reply,
and at this point in time the host is already broadcasting TIPC
data, so there are no real security concerns.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Jacob Keller [Sat, 21 Apr 2012 06:05:40 +0000 (06:05 +0000)]
ixgbe: check for WoL support in single function
This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Wed, 18 Apr 2012 02:57:44 +0000 (02:57 +0000)]
igb: Force flow control off during reset when forcing speed.
During igb_reset(), we initiate a hardware reset which will clear our
flow control settings. For auto-negotiation, we re-negotiate them when
linking up again, but we need to force them off properly for the forced
speed case.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 20 Mar 2012 03:47:52 +0000 (03:47 +0000)]
e1000e: 82579 potential system hang on stress when ME enabled
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 20 Mar 2012 03:47:47 +0000 (03:47 +0000)]
e1000e: 82579 packet drop workaround
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 16 Mar 2012 09:02:59 +0000 (09:02 +0000)]
e1000e: Enable DMA Burst Mode on 82574 by default.
Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 16 Mar 2012 09:02:58 +0000 (09:02 +0000)]
e1000e: Disable Far-End LoopBack following reset on 80003ES2LAN.
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
qlcnic: Allow a predefined set of capture masks for FW dump
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Include the header to pickup the definitions of the global symbols.
Quiets the following sparse warnings:
warning: symbol 'crush_find_rule' was not declared. Should it be static?
warning: symbol 'crush_do_rule' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Sage Weil <sage@newdream.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
isdn/eicon: use standard __init,__exit function markup
Remove the custom DIVA_{INIT,EXIT}_FUNCTION defines and use
the standard __init,__exit markup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Armin Schindler <mac@melware.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Tore Anderson from :
https://bugzilla.kernel.org/show_bug.cgi?id=42572
When RTAX_FEATURE_ALLFRAG is set on a route, the effective TCP segment
size does not take into account the size of the IPv6 Fragmentation
header that needs to be included in outbound packets, causing every
transmitted TCP segment to be fragmented across two IPv6 packets, the
latter of which will only contain 8 bytes of actual payload.
RTAX_FEATURE_ALLFRAG is typically set on a route in response to
receving a ICMPv6 Packet Too Big message indicating a Path MTU of less
than 1280 bytes. 1280 bytes is the minimum IPv6 MTU, however ICMPv6
PTBs with MTU < 1280 are still valid, in particular when an IPv6
packet is sent to an IPv4 destination through a stateless translator.
Any ICMPv4 Need To Fragment packets originated from the IPv4 part of
the path will be translated to ICMPv6 PTB which may then indicate an
MTU of less than 1280.
The Linux kernel refuses to reduce the effective MTU to anything below
1280 bytes, instead it sets it to exactly 1280 bytes, and
RTAX_FEATURE_ALLFRAG is also set. However, the TCP segment size appears
to be set to 1240 bytes (1280 Path MTU - 40 bytes of IPv6 header),
instead of 1232 (additionally taking into account the 8 bytes required
by the IPv6 Fragmentation extension header).
This in turn results in rather inefficient transmission, as every
transmitted TCP segment now is split in two fragments containing
1232+8 bytes of payload.
After this patch, all the outgoing packets that includes a
Fragmentation header all are "atomic" or "non-fragmented" fragments,
i.e., they both have Offset=0 and More Fragments=0.
With help from David S. Miller
Reported-by: Tore Anderson <tore@fud.no> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Tom Herbert <therbert@google.com> Tested-by: Tore Anderson <tore@fud.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Thu, 26 Apr 2012 21:57:17 +0000 (17:57 -0400)]
tipc: Enhance error checking of published names
Consolidates validation of scope and name sequence range values into
a single routine where it applies both to local name publications
and to name publications issued by other nodes in the network. This
change means that the scope value for non-local publications is now
validated and the name sequence range for local publications is now
validated only once. Additionally, a publication attempt that fails
validation now creates an entry in the system log file only if debugging
capabilities have been enabled; this prevents the system log from being
cluttered up with messages caused by a defective application or network
node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 26 Apr 2012 21:53:03 +0000 (17:53 -0400)]
tipc: Create helper routine to delete unused name sequence structure
Replaces two identical chunks of code that delete an unused name
sequence structure from TIPC's name table with calls to a new routine
that performs this operation.
This change is cosmetic and doesn't impact the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 26 Apr 2012 21:41:35 +0000 (17:41 -0400)]
tipc: Optimize initialization of network topology service
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 26 Apr 2012 21:21:49 +0000 (17:21 -0400)]
tipc: Enhance re-initialization of network topology service
Streamlines the job of re-initializing TIPC's network topology service
when a node's network address is first assigned. Rather than destroying
the topology server port and breaking its connections to existing
subscribers, TIPC now simply lets the service continue running (since
the change to the port identifier of each port used by the topology
service no longer impacts the flow of messages between the service and
its subscribers).
This enhancement means that applications that utilize the topology
service prior to the assignment of TIPC's network address no longer need
to re-establish their subscriptions when the address is finally assigned.
However, it is worth noting that any subsequent events for existing
subscriptions report the new port identifier of the publishing port,
rather than the original port identifier. (For example, a name that was
previously reported as being published by <0.0.0:ref> may be subsequently
withdrawn by <Z.C.N:ref>.)
This doesn't impact any of the existing known userspace in tipc-utils,
since (a) TIPC continues to treat references to the original port ID
correctly and (b) normal use cases assign an address before active use.
However if there does happen to be some rare/custom application out
there that was relying on this, they can simply bypass the enhancement
by issuing a subscription to {0,0} and break its connection to the
topology service, if an associated withdrawal event occurs.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 26 Apr 2012 21:17:39 +0000 (17:17 -0400)]
tipc: Optimize termination of configuration service
Termination no longer tests to see if the configuration service
port was successfully created or not. In the unlikely event that the
port was not created, attempting to delete the non-existent port is
detected gracefully and causes no harm.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 26 Apr 2012 20:50:22 +0000 (16:50 -0400)]
tipc: Optimize initialization of configuration service
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allan Stephens [Thu, 26 Apr 2012 20:46:29 +0000 (16:46 -0400)]
tipc: Optimize re-initialization of configuration service
Streamlines the job of re-initializing TIPC's configuration service
when a node's network address is first assigned. Rather than destroying
the configuration server port and then recreating it, TIPC now simply
withdraws the existing {0,<0.0.0>} name publication and creates a new
{0,<Z.C.N>} name publication that identifies the node's network address
to interested subscribers.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pavel Emelyanov [Wed, 25 Apr 2012 23:43:04 +0000 (23:43 +0000)]
tcp repair: Fix unaligned access when repairing options (v2)
Don't pick __u8/__u16 values directly from raw pointers, but instead use
an array of structures of code:value pairs. This is OK, since the buffer
we take options from is not an skb memory, but a user-to-kernel one.
For those options which don't require any value now, require this to be
zero (for potential future extension of this API).
v2: Changed tcp_repair_opt to use two __u32-s as spotted by David Laight.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Added support for fragmentation of E1 interfaces of hfcmulti driver.
Fragmentation is usefull if multiple devices are connected to an E1
interface. Each fragment will have a subset of the available timeslots.
These devices require a cascde connection or a multiplexer.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Rework of LED status display for HFC-4S/8S/E1 cards.
LEDs will show RED if layer 1 is disabled or fails.
LEDs will show GREEN if layer 1 is active.
LEDs will blink if traffic on D-channel.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Using FLG_ACTIVE flag to determine if layer 1 is active or not.
We already have the flag for L1 active, so we should use it.
L2 will be solved in a later patch.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Fixed false interruption of audio during bridging change.
Transmitted audio data was interrupted if a bridge was enabled or disabled.
Now transmission seamlessly continues during that action.
Fix in hfcmulti.ko
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
merge TXQ/RXQ/MAC start/enable code to one function as they
are started/enabled at the same time, just like stop/disable them
in the function of atl1c_stop_mac.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This function is used for suspend of S1/S3/S4 and driver remove.
It sets MAC/PHY based on the WoL configuation to get lower power
consumption.
atl1c_phy_power_saving is renamed to atl1c_phy_to_ps_link, this
function is just make PHY enter a link/speed mode to eat less
power.
REG_MAC_CTRL register is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Many magic data are re-configured for PHY during its reset operation
based on chip type to get better compability and stability.
REG_PHY_CTRL register may be configured by BIOS before enter OS.
so, the driver can't directly write to it without any Read-Op.
this change also affect suspend and phy_disable routines.
PHY debug ports and extension registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bit 17/18 of reg1424 must be clear for l2cb 1.x, or it will cause
the write-reg operation fail without cable connected.
so, please do connect the cable when apply this patch to the driver
to make sure these 2bits are cleared by new driver.
The revised code is move to al1c_reset_mac.
SERDES register definition is refined as well.
when do reset MAC, speed/duplex control right should be transferred
to software before do PHY auto-neg -- by bit MASTER_CTRL_SPEED_MODE_SW.
SERDES register definition is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
phy register is read/write via MDIO control module ---
that module will be affected by the hibernate status,
to access phy regs in hib stutus, slow frequency clk must
be selected.
To access phy extension register, the MDIO related
registers are refined/updated, a _core function is
re-wroted for both regular PHY regs and extension regs.
existing PHY r/w function is revised based on the _core.
PHY extension registers will be used for the comming
patches.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Skip flashing a FW component if that component is not present in a
particular FW UFI image.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: Fix wrong status getting returned for MCC commands
MCC Response CQEs are processed as part of NAPI poll routine and
also synchronously. If MCC completions are consumed by NAPI poll
routine, wrong status is returned to synchronously waiting routine.
Fix this by getting status of MCC command from command response
instead of response CQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
EQ is getting armed wrongly in INTx mode as INTx interrupt is taking
some time to deassert. This can cause another interrupt while NAPI is
scheduled and scheduling a NAPI in interrupt does not take effect.
This causes interrupt to be missed and traffic stalls. Fixing this by
preventing wrong arming of EQ.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN and multicast hardware filters are limited and can get
exhausted in adapters with many PCI functions. If setting
a VLAN or multicast filter fails due to lack of sufficient
hardware resources, these packets get dropped. Fix this by
switching to VLAN or multicast promiscous mode so that these
packets are not dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dsp_spl_jiffies need to be the same datatype as jiffies (which is ulong).
If not, on 64 bit systems it will fallback to schedule the DSP every jiffie
tic as soon jiffies become > 2^32.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Fixed hardware bridging/conference check routine of mISDN_dsp.ko.
In some cases the hardware bridging/conference (2-n parties) was selected,
but still pure software bridging/conference was used.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Fix NULL pointer bug in if-condition of mISDN_dsp
Fix a bug (was introduced by a cut & paste error)
in cases when dsp->conf was NULL.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 20 Apr 2012 09:49:23 +0000 (09:49 +0000)]
net: dcb: add CEE notify calls
This adds code to trigger CEE events when an APP change or setall
command is made from user space. This simplifies user space code
significantly by creating a single interface to listen on that
works with both firmware and userland agents.
And if we end up with multiple agents this keeps every thing in
sync userland agents, firmware agents, and kernel notifier consumers.
For an example agent that listens for these events see:
https://github.com/jrfastab/cgdcbxd
cgdcbxd is a daemon used to monitor DCB netlink events and manage
the net_prio control group sub-system.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Shmulik Ravid <shmulikr@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adds hepler to clean sdata ieee80211_clean_sdata similar way as
ieee80211_setup_sdata is implemented. The function will be used by other
interfaces later.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 23 Apr 2012 17:49:03 +0000 (19:49 +0200)]
mac80211: fix num_mcast_sta counting issues
Moving a STA to an AP VLAN prevents num_mcast_sta from being decremented
once the STA leaves, because sta->sdata changes. Fix this by checking
for AP VLANs as well.
Also exclude 4-addr VLAN stations from num_mcast_sta - remote 4-addr
stations ignore 3-address multicast frames anyway. In a typical bridge
configuration they receive the same packets as 4-address unicast.
This patch also fixes clearing the sdata->u.vlan.sta pointer when the
STA is removed from a 4-addr VLAN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log