alloc_ordered_workqueue() with WQ_MEM_RECLAIM set, replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "close_wq" queues work items &ctx->close_work (maps to
ucma_close_id) and &con_req_eve->close_work (maps to
ucma_close_event_id). It has been identity converted.
WQ_MEM_RECLAIM has been set to ensure forward progress under
memory pressure.
When LAG is active, QP tx affinity (the physical port
to which a QP is affined, or the TIS in case of raw-eth)
is set in a round robin fashion during state transition
from RESET to INIT.
This is done in two steps:
1) Issuing CREATE_VPORT_LAG in order to have Ethernet traffic from
both ports arriving on PF0 root flowtable, so we will be able to catch
all raw-eth traffic on PF0.
2) Creation of LAG demux flowtable in order to direct all non-raw-eth
traffic back to its source port, assuring that normal Ethernet
traffic "jumps" to the root flowtable of its RX port (non-LAG behavior).
IB/mlx5: Port events in RoCE now rely on netdev events
Since ib_query_port() in RoCE returns the state of its netdev as the port
state, it makes sense to propagate the port up/down events to ib_core
when the netdev port state changes, instead of relying on traditional
core events.
This also keeps both the event and ib_query_port() synchronized.
Maor Gottlieb [Tue, 30 Aug 2016 13:58:32 +0000 (16:58 +0300)]
IB/uverbs: Add support to extend flow steering specifications
Flow steering specifications structures were implemented as in an
extensible way that allows one to add new filters and new fields
to existing filters.
These specifications have never been extended, therefore the
kernel flow specifications size and the user flow specifications size
were must to be equal.
In downstream patch, the IPv4 flow specifications type is extended to
support TOS and TTL fields.
To support an extension we change the flow specifications size
condition test to be as following:
* If the user flow specifications is bigger than the kernel
specifications, we verify that all the bits which not in the kernel
specifications are zeros and the flow is added only with the kernel
specifications fields.
* Otherwise, we add flow rule only with the user specifications fields.
User space filters must be aligned with 32bits.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Maor Gottlieb [Sun, 28 Aug 2016 11:16:34 +0000 (14:16 +0300)]
IB/mlx5: Add sniffer support to steering
Add support to create sniffer rule. This rule receive all
incoming and outgoing packets from the port.
A user could create such rule by using IB_FLOW_ATTR_SNIFFER type.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Maor Gottlieb [Sun, 28 Aug 2016 11:16:33 +0000 (14:16 +0300)]
IB/mlx5: Increase flow table reference count in create rule
Move the reference count increasing of flow table to be in
create_flow_rule, it will increase the reference count for each rule
creation and not for each flow.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Maor Gottlieb [Sun, 28 Aug 2016 11:16:31 +0000 (14:16 +0300)]
IB/mlx5: Save flow table priority handler instead of index
Saving the flow table priority object's pointer in the flow handle
is necessary for downstream patches since the sniffer flow table isn't
placed at the standard flow_db structure but in a different database.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Alex Vesker [Sun, 28 Aug 2016 09:25:53 +0000 (12:25 +0300)]
IB/mlx5: Add port counter support for raw packet QP
Counters weren't updated due to raw packet QPs' traffic since the
counter-id was not associated with the QP. Added support for
associating the q-counter-id with the raw packet QP. The attachment
is done only when changing RQ raw packet QP state from RST to INIT
in modify-RQ command. FW support is required for the above, without
this support raw packet QP counters will not count.
Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
Yishai Hadas [Sun, 28 Aug 2016 08:28:45 +0000 (11:28 +0300)]
IB/mlx5: Expose RSS related capabilities
Expose RSS related capabilities on both IB and vendor channels.
In addition to the IB capabilities the driver reports some extra
capabilities on its vendor channel:
- Bit mask of the supported types of hash functions.
- Bit mask of the supported RX fields that can participate
in the RX hashing.
Those capabilities are applicable only when the link layer
is Ethernet.
Yishai Hadas [Sun, 28 Aug 2016 08:28:43 +0000 (11:28 +0300)]
IB/core: Expose RSS related capabilities
Expose RSS related capabilities, it includes both direct ones (i.e.
struct ib_rss_caps) and max_wq_type_rq which may be used in both
RSS and non RSS flows.
Specifically,
supported_qpts:
- QP types that support RSS on the device.
max_rwq_indirection_tables:
- Max number of receive work queue indirection tables that
could be opened on the device.
max_rwq_indirection_table_size:
- Max size of a receive work queue indirection table.
max_wq_type_rq:
- Max number of work queues of receive type that
could be opened on the device.
We now only use it from ib_alloc_pd to create a local DMA lkey if the
device doesn't provide one, or a global rkey if the ULP requests it.
This patch removes ib_get_dma_mr and open codes the functionality in
ib_alloc_pd so that we can simplify the code and prevent abuse of the
functionality. As a side effect we can also simplify things by removing
the valid access bit check, and the PD refcounting.
In the future I hope to also remove the per-PD global MR entirely by
shifting this work into the HW drivers, as one step towards avoiding
the struct ib_mr overload for various different use cases.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/core: add support to create a unsafe global rkey to ib_create_pd
Instead of exposing ib_get_dma_mr to ULPs and letting them use it more or
less unchecked, this moves the capability of creating a global rkey into
the RDMA core, where it can be easily audited. It also prints a warning
everytime this feature is used as well.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
This has two reasons: a) to clearly mark that drivers don't have any
business using it, and b) because we're going to use it for the
(dangerous) global rkey soon, so that drivers don't create on themselves.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Salil [Tue, 23 Aug 2016 20:44:50 +0000 (04:44 +0800)]
IB/hns: Add support of ACPI to the Hisilicon RoCE driver
This patch is meant to add support of ACPI to the Hisilicon RoCE
driver.
Changes done are primarily meant to detect the type and then either
use DT specific or ACPI spcific functions. Where ever possible,
this patch tries to make use of Unified Device Property Interface
APIs to support both DT and ACPI through single interface.
This patch depends upon HNS ethernet driver to Reset RoCE. This
function within HNS ethernet driver has also been enhanced to
support ACPI and is part of other accompanying patch with this
patch-set.
NOTE: The changes in this patch are done over below branch,
https://github.com/dledford/linux/tree/hns-roce
Salil [Tue, 23 Aug 2016 20:44:49 +0000 (04:44 +0800)]
net: hns: Add support of ACPI to HNS driver RoCE Reset function
In the Hip06 SoC, the RoCE Engine is part of the Hisilicon Network
Subsystem and is dependent upon DSAF module. Therefore, certain
functions like RESET are exposed through the common registers of
HNS DSAF module which are memory-mapped by the HNS driver and
currently can only be accessed through DT/syscon interface.
This patch adds the support of ACPI to the existing RoCE reset
function in the HNS driver(please refer NOTE 2). Hisilicon RoCE
driver (please refer NOTE 1) shall call this reset function during
probe time to reset the RoCE Engine.
The HNS Reset function indirectly ends up in calling the _DSM()
function part of the DSDT ACPI Table. Actual reset functionality
for ACPI is implemented within the ACPI DSDT Table which also has
been enhanced to support this change.
Support of ACPI in the HNS RoCE driver shall be pushed through a
different accompanying below patch:
"IB/hns: Add support of ACPI to the Hisilicon RoCE Driver"
NOTE 1: HNS RoCE driver has already been accepted by its maintainer
Doug Ledford<dledford@redhat.com>. Please refer below link:
https://www.spinics.net/lists/linux-rdma/msg38850.html
NOTE 2: RoCE reset function patch has been accepted and now is
part of the net-next:
https://www.mail-archive.com/netdev@vger.kernel.org/msg123867.html
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
Wei Yongjun [Sat, 6 Aug 2016 01:01:24 +0000 (01:01 +0000)]
IB/hns: Fix return value check in hns_roce_get_cfg()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Philippe Reynes [Fri, 19 Aug 2016 22:52:19 +0000 (00:52 +0200)]
net: ethernet: renesas: ravb: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Fri, 19 Aug 2016 22:52:18 +0000 (00:52 +0200)]
net: ethernet: renesas: ravb: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Aug 2016 04:58:49 +0000 (21:58 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-20
This series contains updates to ixgbe and ixgbevf.
Veola fixes how the backplane reports the media in ethtool, as KR, KX or
KX4 based on the backplane interface present.
Emil fixes ixgbevf since an incorrect size parameter for
ixgbevf_write_msg_read_ack() ended up only giving the PF the first 4
bytes of the MAC address, so correct the size by calculating it on the
fly for all instances where we call ixgbevf_write_msg_read_ack(). Added
geneve receive offload support for x550em_a.
Don fixes the LED interface for x557 since it uses a different interface.
Added support for the new x557 copper device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Thu, 18 Aug 2016 00:34:40 +0000 (20:34 -0400)]
ixgbe: Add support for new X557 device
This patch adds support for the new copper device X557.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 17 Aug 2016 21:34:07 +0000 (17:34 -0400)]
ixgbe: add device to MDIO speed setting
This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 17 Aug 2016 18:11:57 +0000 (14:11 -0400)]
ixgbe: Fix led interface for X557 devices
The X557 devices use a different interface to the LED for the port.
This patch reflect that change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 10 Aug 2016 18:19:23 +0000 (11:19 -0700)]
ixgbe: add support for geneve Rx offload
Add geneve Rx offload support for x550em_a.
The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.
Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().
Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 27 Jul 2016 17:55:08 +0000 (10:55 -0700)]
ixgbevf: fix incorrect MAC address on load
The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().
Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Veola Nazareth [Sun, 21 Aug 2016 02:35:37 +0000 (19:35 -0700)]
ixgbe: report correct media type for KR, KX and KX4 interfaces
ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Markus Elfring [Sat, 20 Aug 2016 06:54:15 +0000 (08:54 +0200)]
tun: Use memdup_user() rather than duplicating its implementation
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Aug 2016 01:56:30 +0000 (18:56 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-08-19
This series contains updates to i40e and i40evf only.
Jake provides several patches, first just moves a function to co-locate
the two functions related to configuring RSS via the admin queue, which
should help in spotting bugs when comparing the two functions. Fixed
an issue where commit e69ff813af35 ("i40e: rework the functions to
configure RSS with similar parameters") missed checking whether the seed
is NULL before using it and did not use the passed in *lut parameter.
Fixed an issue where a previous refactor missed i40e_vsi_config_rss()
and the values were being ignored, so checked for the fields and used
them instead of default values. Lastly replaced calls to
create_singlethread_workqueue() with alloc_workqueue() to provide more
control over workqueue creation and allows explicit setting of the
desired mode of operation.
Mitch adds link speed to log messages and reports speed through ethtool.
Carolyn refactors tail bump check and fixes byte ordering problems found
when enabling this feature support. Adds support for HMC resources and
profile commands for x722 firmware.
Heinrich Schuchardt fixes format identifiers from %u to %d since the
variable is defined as an integer.
Catherine fixes an issue where there was a race condition between the
completion of the client open and calls to the client ops, so ensured
that client ops are not called until we are sure client is open.
Harshitha makes sure that i40e_client_release() does not try to use
an adapter pointer which may not be initialized, so make sure it is.
Joe Perches fixes the use of the local macro XSTRINGIFY() to use
__stringify() instead.
Avinash corrects the mutex usage in client_subtask(). Fixed the RDMA
client to open again after reset since it is closed during a PF reset.
Jeff (me) clean up whitespace issues, where indentation was done
inconsistently and with spaces versus tabs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Fri, 19 Aug 2016 18:55:44 +0000 (11:55 -0700)]
samples/bpf: Add tunnel set/get tests.
The patch creates sample code exercising bpf_skb_{set,get}_tunnel_key,
and bpf_skb_{set,get}_tunnel_opt for GRE, VXLAN, and GENEVE. A native
tunnel device is created in a namespace to interact with a lwtunnel
device out of the namespace, with metadata enabled. The bpf_skb_set_*
program is attached to tc egress and bpf_skb_get_* is attached to egress
qdisc. A ping between two tunnels is used to verify correctness and
the result of bpf_skb_get_* printed by bpf_trace_printk.
Signed-off-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 19 Aug 2016 21:47:09 +0000 (14:47 -0700)]
hv_netvsc: Implement batching of receive completions
The existing code uses busy retry when unable to send out receive
completions due to full ring buffer. It also gives up retrying after limit
is reached, and causes receive buffer slots not being recycled.
This patch implements batching of receive completions. It also prevents
dropping receive completions due to full ring buffer.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Sat, 20 Aug 2016 04:47:41 +0000 (21:47 -0700)]
i40e/i40evf: Fix indentation
Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.
Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Avinash Dayanand [Wed, 17 Aug 2016 23:04:06 +0000 (16:04 -0700)]
i40e: Correcting mutex usage in client code
Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.
This is a patch suggested by RDMA team.
Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852 Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Wed, 17 Aug 2016 10:37:31 +0000 (03:37 -0700)]
i40e: Remove XSTRINGIFY macro definitions and uses
Use __stringify instead.
Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Initialize pointer in client_release function
The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.
Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8 Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Check client is open before calling client ops
We were having a race between the completion of the client open and
calls to the client ops so don't call a client op unless we are sure the
client is open.
Testing Hints: Load IWARP driver and make sure it works as expected.
Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Thu, 4 Aug 2016 18:37:04 +0000 (11:37 -0700)]
i40e: Fix byte ordering in ARP NS code for X722
This patch fixes byte ordering problems found when enabling this feature
support. Without this patch, the feature will not work correctly. This
patch fixes the definitions to have the correct byte order.
Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 4 Aug 2016 18:37:02 +0000 (11:37 -0700)]
i40evf: report link speed
The PF driver tells us the link speed, so do something with that
information. Add link speed to log messages, and report speed through
ethtool.
Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 4 Aug 2016 18:37:01 +0000 (11:37 -0700)]
i40e: use alloc_workqueue instead of create_singlethread_workqueue
Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".
Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 19 Jul 2016 23:23:31 +0000 (16:23 -0700)]
i40e: use configured RSS key and lookup table in i40e_vsi_config_rss
A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 19 Jul 2016 23:23:30 +0000 (16:23 -0700)]
i40e: fix broken i40e_config_rss_aq function
X722 hardware requires using the admin queue to configure RSS. This
function was previously re-written in commit e69ff813af35 ("i40e: rework
the functions to configure RSS with similar parameters").
However, the previous refactor did not work correctly for a few reasons
(a) it does not check whether seed is NULL before using it, resulting in
a NULL pointer dereference
(b) it does not even bother to use the passed in *lut parameter which
defines the requested lookup table. Instead it uses its own round robin
table.
Fix these issues by re-writing it to be similar to i40e_config_rss_reg
and i40e_get_rss_aq.
Fixes: e69ff813af35 ("i40e: rework the functions to configure RSS with similar parameters", 2015-10-21) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vegard Nossum [Fri, 19 Aug 2016 16:08:57 +0000 (18:08 +0200)]
net/irda: remove pointless assignment/check
We've already set sk to sock->sk and dereferenced it, so if it's NULL
we would have crashed already. Moreover, if it was NULL we would have
crashed anyway when jumping to 'out' and trying to unlock the sock.
Furthermore, if we had assigned a different value to 'sk' we would
have been calling lock_sock() and release_sock() on different sockets.
My conclusion is that these two lines are complete nonsense and only
serve to confuse the reader.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Fri, 19 Aug 2016 06:33:31 +0000 (09:33 +0300)]
qed: utilize FW 8.10.10.0
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 20 Aug 2016 00:19:20 +0000 (17:19 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-18
This series contains updates to ixgbe and ixgbevf.
Emil cleans up confusing amongst the users by making an error message
into a debug message, since the TXDCTL.ENABLE (and comparable
VFTXDCTL.ENABLE for ixgbevf) bit is set only when the
transmit queue is actually enabled, which may not happen during the
configure phase eve if we waited for it. Converts to using netdev_dbg()
macro instead of our home brewed macro for ixgbevf. Converted the
service task to use atomic bitwise operations when setting and checking
reset requests to reduce the possibility of race conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series converts the bcm_sf2 driver from a traditional DSA driver
into a platform_device driver and makes it use the new DSA binding that Andrew
introduced in the latest merge window.
Prior attempts used to coerce the code in net/dsa/dsa2.c to accept the old
binding, while really there is only one broken single user out there: bcm_sf2,
so instead, just assume the new DT binding is deployed and use it accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 18 Aug 2016 22:30:16 +0000 (15:30 -0700)]
net: dsa: bcm_sf2: Remove probing through old DSA binding
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 18 Aug 2016 22:30:15 +0000 (15:30 -0700)]
net: dsa: bcm_sf2: Use device managed helpers
Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 18 Aug 2016 22:30:14 +0000 (15:30 -0700)]
net: dsa: bcm_sf2: Make it a real platform device driver
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 18 Aug 2016 22:30:12 +0000 (15:30 -0700)]
net: dsa: Export suspend/resume functions
In preparation for allowing switch drivers to implement system-wide
suspend/resume functions, export dsa_switch_suspend and
dsa_switch_resume() such that these are callable from the appropriate
driver specific suspend/resume functions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 20 Aug 2016 00:14:08 +0000 (17:14 -0700)]
Merge branch 'mv88e6xxx-fix-wait'
Andrew Lunn says:
====================
Fix mv88e6xxx wait function
The mv88e6xxx wait function can be upset of the system has nots of
other things to do and a sleep takes a lot longer than expected. Fix
this be using a fixed number of iterations, rather than a fixed
walkclock time.
Witht that change made, it is possible to consoliate another
wait function.
A wait actually timing out should not happen and when it does, it
means something serious is wrong. Make sure an error is logged,
since not all callers will log an error.
====================
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 18 Aug 2016 22:01:56 +0000 (00:01 +0200)]
dsa: mv88e6xxx: Use mv88e6xx_wait in mv88e6xxx_update()
Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 18 Aug 2016 22:01:55 +0000 (00:01 +0200)]
dsa: mv88e6xxx: Timeout based on iterations, not time
The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.
Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 20 Aug 2016 00:11:50 +0000 (17:11 -0700)]
Merge branch 'phy-next'
Andrew Lunn says:
====================
PHY Kconfig and Makefile cleanup
The Ethernet PHY directory has slowly been getting more entries.
Split the entries in the Makefile and Kconfig into MDIO bus drivers
and PHYs. Within these two groups, sort them. This should reduce merge
conflicts and aid finding what one searches for.
The Kconfig text contains redundant "Driver for" and "Support for"
which add little value, make the vendor less obvious, and defeat the
shortcut key in the menu. Remove such text.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 18 Aug 2016 21:56:06 +0000 (23:56 +0200)]
net: phy: Kconfig: Remove redundant "Support for"
Remove the redundant "Support for" and "Drivers for" from the Kconfig
short description. This makes the manufacture much more prominent in
the list and makes the shortcut keys useful.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 18 Aug 2016 21:56:05 +0000 (23:56 +0200)]
net: phy: Sort Makefile and Kconfig
Sort the files to reduce merge conflicts and to make it easier to find
drivers by name. Also separate the MDIO bus drivers from the PHY
drivers, again to help find what you need.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 Aug 2016 17:19:34 +0000 (10:19 -0700)]
net: ipv4: fix sparse error in fib_good_nh()
Fixes following sparse errors :
net/ipv4/fib_semantics.c:1579:61: warning: incorrect type in argument 2
(different base types)
net/ipv4/fib_semantics.c:1579:61: expected unsigned int [unsigned]
[usertype] key
net/ipv4/fib_semantics.c:1579:61: got restricted __be32 const
[usertype] nh_gw
Fixes: a6db4494d218c ("net: ipv4: Consider failed nexthops in multipath routes") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 18 Aug 2016 16:37:51 +0000 (11:37 -0500)]
ibmvnic: Handle backing device failover and reinitialization
An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
oulijun [Thu, 18 Aug 2016 12:32:52 +0000 (20:32 +0800)]
net: hns: Add reset function support for RoCE driver
It added reset function for RoCE driver. RoCE is a feature of hns.
In hip06 SoC, in RoCE reset process, it's needed to configure dsaf
channel reset, port and sl map info. Reset function of RoCE is
located in dsaf module, we only call it in RoCE driver when needed.
This patch is used to fix the conflict, please refer to this link:
https://www.spinics.net/lists/linux-rdma/msg39114.html
Signed-off-by: Wei Hu <xavier.huwei@huawei.com> Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com> Signed-off-by: Lijun Ou <oulijun@huawei.com> Signed-off-by: Sheng Li <lisheng011@huawei.com> Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Aug 2016 21:40:25 +0000 (14:40 -0700)]
Merge branch 'rhash-raw-walkers-remove-part-1'
Herbert Xu says:
====================
rhashtable: Get rid of raw table walkers part 1
This series starts the process of getting rid of all raw rhashtable
walkers (e.g., using any of the rht_for_each helpers) from the
kernel.
We need to do this before I can fix the resize kmalloc failure issue
by using multi-layered tables.
We should do this anyway because almost all raw table walkers are
already buggy in that they don't handle multiple rhashtables during
a resize.
====================
Dave/Tomas, please keep an eye out for any new patches that try
to introduce raw table walkers and nack them.
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log