bnx2x: Add a missing bit for PXP parity register of 57712.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Today was as good as any other day, but I felt I had to do things I love
to when paying hommage to somebody I love, so please apply this one,
something he would be proud of, even if so geekly.
Way past it was/is deserved.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
addr_type of 0 means that the type should be adopted from from_dev and
not from __hw_addr_del_multiple(). Unfortunately it isn't so and
addr_type will always be considered. Fix this by implementing the
considered and documented behavior.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
would flush the newly created net, not the original one.
The equivalent ipv4 code is correct (stores the net inside ->extra1). Acked-by: Daniel Lezcano <daniel.lezcano@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Reported-by: George Billios <gbillios@gmail.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Henry Nestler [Tue, 22 Feb 2011 11:29:42 +0000 (11:29 +0000)]
DM9000B: Fix PHY power for network down/up
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Feb 2011 03:48:38 +0000 (03:48 +0000)]
sfc: lower stack usage in efx_ethtool_self_test
drivers/net/sfc/ethtool.c: In function ‘efx_ethtool_self_test’:
drivers/net/sfc/ethtool.c:613: warning: the frame size of 1200 bytes
is larger than 1024 bytes
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Thu, 17 Feb 2011 08:17:52 +0000 (08:17 +0000)]
bridge: Use IPv6 link-local address for multicast listener queries
Currently the bridge multicast snooping feature periodically issues
IPv6 general multicast listener queries to sense the absence of a
listener.
For this, it uses :: as its source address - however RFC 2710 requires:
"To be valid, the Query message MUST come from a link-local IPv6 Source
Address". Current Linux kernel versions seem to follow this requirement
and ignore our bogus MLD queries.
With this commit a link local address from the bridge interface is being
used to issue the MLD query, resulting in other Linux devices which are
multicast listeners in the network to respond with a MLD response (which
was not the case before).
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Thu, 17 Feb 2011 08:17:51 +0000 (08:17 +0000)]
bridge: Fix MLD queries' ethernet source address
Map the IPv6 header's destination multicast address to an ethernet
source address instead of the MLD queries multicast address.
For instance for a general MLD query (multicast address in the MLD query
set to ::), this would wrongly be mapped to 33:33:00:00:00:00, although
an MLD queries destination MAC should always be 33:33:00:00:00:01 which
matches the IPv6 header's multicast destination ff02::1.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Tue, 15 Feb 2011 13:19:21 +0000 (13:19 +0000)]
bridge: Allow mcast snooping for transient link local addresses too
Currently the multicast bridge snooping support is not active for
link local multicast. I assume this has been done to leave
important multicast data untouched, like IPv6 Neighborhood Discovery.
In larger, bridged, local networks it could however be desirable to
optimize for instance local multicast audio/video streaming too.
With the transient flag in IPv6 multicast addresses we have an easy
way to optimize such multimedia traffic without tempering with the
high priority multicast data from well-known addresses.
This patch alters the multicast bridge snooping for IPv6, to take
effect for transient multicast addresses instead of non-link-local
addresses.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Tue, 15 Feb 2011 13:19:20 +0000 (13:19 +0000)]
ipv6: Add IPv6 multicast address flag defines
This commit adds the missing IPv6 multicast address flag defines to
complement the already existing multicast address scope defines and to
be able to check these flags nicely in the future.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Tue, 15 Feb 2011 13:19:18 +0000 (13:19 +0000)]
bridge: Fix IPv6 multicast snooping by correcting offset in MLDv2 report
We actually want a pointer to the grec_nsrcr and not the following
field. Otherwise we can get very high values for *nsrcs as the first two
bytes of the IPv6 multicast address are being used instead, leading to
a failing pskb_may_pull() which results in MLDv2 reports not being
parsed.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Tue, 15 Feb 2011 13:19:17 +0000 (13:19 +0000)]
bridge: Fix IPv6 multicast snooping by storing correct protocol type
The protocol type for IPv6 entries in the hash table for multicast
bridge snooping is falsely set to ETH_P_IP, marking it as an IPv4
address, instead of setting it to ETH_P_IPV6, which results in negative
look-ups in the hash table later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel J Blueman [Mon, 21 Feb 2011 16:11:06 +0000 (00:11 +0800)]
fix cfg80211_wext_siwfreq lock ordering...
I previously managed to reproduce a hang while scanning wireless
channels (reproducible with airodump-ng hopping channels); subsequent
lockdep instrumentation revealed a lock ordering issue.
Without knowing the design intent, it looks like the locks should be
taken in reverse order; please comment.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.38-rc5-341cd #4
-------------------------------------------------------
airodump-ng/15445 is trying to acquire lock:
(&rdev->devlist_mtx){+.+.+.}, at: [<ffffffff816b1266>]
cfg80211_wext_siwfreq+0xc6/0x100
but task is already holding lock:
(&wdev->mtx){+.+.+.}, at: [<ffffffff816b125c>] cfg80211_wext_siwfreq+0xbc/0x100
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
https://bugzilla.kernel.org/show_bug.cgi?id=16608
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yuchung Cheng [Mon, 7 Feb 2011 12:57:04 +0000 (12:57 +0000)]
tcp: undo_retrans counter fixes
Fix a bug that undo_retrans is incorrectly decremented when undo_marker is
not set or undo_retrans is already 0. This happens when sender receives
more DSACK ACKs than packets retransmitted during the current
undo phase. This may also happen when sender receives DSACK after
the undo operation is completed or cancelled.
Fix another bug that undo_retrans is incorrectly incremented when
sender retransmits an skb and tcp_skb_pcount(skb) > 1 (TSO). This case
is rare but not impossible.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
In the beginning with batching unreg_list was a list that was used only
once in the lifetime of a network device (I think). Now we have calls
using the unreg_list that can happen multiple times in the life of a
network device like dev_deactivate and dev_close that are also using the
unreg_list. In addition in unregister_netdevice_queue we also do a
list_move because for devices like veth pairs it is possible that
unregister_netdevice_queue will be called multiple times.
So I think the change below to fix dev_deactivate which Eric D. missed
will fix this problem. Now to go test that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Bohac [Thu, 17 Feb 2011 13:12:08 +0000 (13:12 +0000)]
sctp: fix reporting of unknown parameters
commit 5fa782c2f5ef6c2e4f04d3e228412c9b4a4c8809 re-worked the
handling of unknown parameters. sctp_init_cause_fixed() can now
return -ENOSPC if there is not enough tailroom in the error
chunk skb. When this happens, the error header is not appended to
the error chunk. In that case, the payload of the unknown parameter
should not be appended either.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 18 Feb 2011 13:30:17 +0000 (13:30 +0000)]
net: dcb: match dcb_app protocol field with 802.1Qaz spec
The dcb_app protocol field is a __u32 however the 802.1Qaz
specification defines it as a 16 bit field. This patch brings
the structure inline with the spec making it a __u16.
CC: Shmulik Ravid <shmulikr@broadcom.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 18 Feb 2011 22:35:56 +0000 (22:35 +0000)]
tcp: fix inet_twsk_deschedule()
Eric W. Biederman reported a lockdep splat in inet_twsk_deschedule()
This is caused by inet_twsk_purge(), run from process context,
and commit 575f4cd5a5b6394577 (net: Use rcu lookups in inet_twsk_purge.)
removed the BH disabling that was necessary.
Add the BH disabling but fine grained, right before calling
inet_twsk_deschedule(), instead of whole function.
With help from Linus Torvalds and Eric W. Biederman
Reported-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Pavel Emelyanov <xemul@openvz.org> CC: Arnaldo Carvalho de Melo <acme@redhat.com> CC: stable <stable@kernel.org> (# 2.6.33+) Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
net: deinit automatic LIST_HEAD
net: dont leave active on stack LIST_HEAD
net: provide default_advmss() methods to blackhole dst_ops
tg3: Restrict phy ioctl access
drivers/net: Call netif_carrier_off at the end of the probe
ixgbe: work around for DDP last buffer size
ixgbe: fix panic due to uninitialised pointer
e1000e: flush all writebacks before unload
e1000e: check down flag in tasks
isdn: hisax: Use l2headersize() instead of dup (and buggy) func.
arp_notify: unconditionally send gratuitous ARP for NETDEV_NOTIFY_PEERS.
cxgb4vf: Use defined Mailbox Timeout
cxgb4vf: Quiesce Virtual Interfaces on shutdown ...
cxgb4vf: Behave properly when CONFIG_DEBUG_FS isn't defined ...
cxgb4vf: Check driver parameters in the right place ...
pch_gbe: Fix the MAC Address load issue.
iwlwifi: Delete iwl3945_good_plcp_health.
net/can/softing: make CAN_SOFTING_CS depend on CAN_SOFTING
netfilter: nf_iterate: fix incorrect RCU usage
pch_gbe: Fix the issue that the receiving data is not normal.
...
Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: fix conn_mon_timer running after disassociate
Low level driver could pass rx frames to us after disassociate, what
can lead to run conn_mon_timer by ieee80211_sta_rx_notify(). That
is obviously wrong, but nothing happens until we unload modules and
resources are used after free. If kernel debugging is enabled following
warning could be observed:
Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Fri, 18 Feb 2011 20:36:06 +0000 (12:36 -0800)]
Merge branch 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
Eric Dumazet [Thu, 17 Feb 2011 22:59:19 +0000 (22:59 +0000)]
net: deinit automatic LIST_HEAD
commit 9b5e383c11b08784 (net: Introduce
unregister_netdevice_many()) left an active LIST_HEAD() in
rollback_registered(), with possible memory corruption.
Even if device is freed without touching its unreg_list (and therefore
touching the previous memory location holding LISTE_HEAD(single), better
close the bug for good, since its really subtle.
(Same fix for default_device_exit_batch() for completeness)
Reported-by: Michal Hocko <mhocko@suse.cz> Tested-by: Michal Hocko <mhocko@suse.cz> Reported-by: Eric W. Biderman <ebiderman@xmission.com> Tested-by: Eric W. Biderman <ebiderman@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Ingo Molnar <mingo@elte.hu> CC: Octavian Purdila <opurdila@ixiacom.com> CC: stable <stable@kernel.org> [.33+] Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 17 Feb 2011 22:54:38 +0000 (22:54 +0000)]
net: dont leave active on stack LIST_HEAD
Eric W. Biderman and Michal Hocko reported various memory corruptions
that we suspected to be related to a LIST head located on stack, that
was manipulated after thread left function frame (and eventually exited,
so its stack was freed and reused).
Eric Dumazet suggested the problem was probably coming from commit 443457242beb (net: factorize
sync-rcu call in unregister_netdevice_many)
This patch fixes __dev_close() and dev_close() to properly deinit their
respective LIST_HEAD(single) before exiting.
Reported-by: Michal Hocko <mhocko@suse.cz> Tested-by: Michal Hocko <mhocko@suse.cz> Reported-by: Eric W. Biderman <ebiderman@xmission.com> Tested-by: Eric W. Biderman <ebiderman@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Ingo Molnar <mingo@elte.hu> CC: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 18 Feb 2011 19:39:01 +0000 (11:39 -0800)]
net: provide default_advmss() methods to blackhole dst_ops
Commit 0dbaee3b37e118a (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 18 Feb 2011 19:32:28 +0000 (11:32 -0800)]
Expand CONFIG_DEBUG_LIST to several other list operations
When list debugging is enabled, we aim to readably show list corruption
errors, and the basic list_add/list_del operations end up having extra
debugging code in them to do some basic validation of the list entries.
However, "list_del_init()" and "list_move[_tail]()" ended up avoiding
the debug code due to how they were written. This fixes that.
So the _next_ time we have list_move() problems with stale list entries,
we'll hopefully have an easier time finding them..
Linus Torvalds [Fri, 18 Feb 2011 01:52:17 +0000 (17:52 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add missing frac fb div flag for dce4+
drm/radeon/kms: do not reject X16 and Y16X16 floating-point formats on r300
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
John Stultz [Sat, 12 Feb 2011 01:45:40 +0000 (17:45 -0800)]
RTC: Revert UIE emulation removal
Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.
Matt Carlson [Tue, 15 Feb 2011 12:51:10 +0000 (12:51 +0000)]
tg3: Restrict phy ioctl access
If management firmware is present and the device is down, the firmware
will assume control of the phy. If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior. This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Tue, 15 Feb 2011 02:08:39 +0000 (02:08 +0000)]
drivers/net: Call netif_carrier_off at the end of the probe
Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).
This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Marciniszyn [Wed, 16 Feb 2011 15:48:25 +0000 (15:48 +0000)]
IB/qib: Prevent double completions after a timeout or RNR error
There is a double completion associated with error handling for RC QPs.
The sequence is:
- The do_rc_ack() routine fields an RNR nack and there are 0
rnr_retries configured on the QP.
- qib_error_qp() stops the pending timer
- qib_rc_send_complete() is called from sdma_complete()
- qib_rc_send_complete() starts the timer because the msb of the psn
just completed says an ack is needed.
- a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
- rc_timeout() calls qib_restart_rc()
- qib_restart_rc() calls qib_send_complete() with a
IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
past
The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Florian Westphal [Thu, 17 Feb 2011 10:32:38 +0000 (11:32 +0100)]
netfilter: tproxy: do not assign timewait sockets to skb->sk
Assigning a socket in timewait state to skb->sk can trigger
kernel oops, e.g. in nfnetlink_log, which does:
if (skb->sk) {
read_lock_bh(&skb->sk->sk_callback_lock);
if (skb->sk->sk_socket && skb->sk->sk_socket->file) ...
in the timewait case, accessing sk->sk_callback_lock and sk->sk_socket
is invalid.
Either all of these spots will need to add a test for sk->sk_state != TCP_TIME_WAIT,
or xt_TPROXY must not assign a timewait socket to skb->sk.
This does the latter.
If a TW socket is found, assign the tproxy nfmark, but skip the skb->sk assignment,
thus mimicking behaviour of a '-m socket .. -j MARK/ACCEPT' re-routing rule.
The 'SYN to TW socket' case is left unchanged -- we try to redirect to the
listener socket.
Amir Hanania [Tue, 15 Feb 2011 09:11:31 +0000 (09:11 +0000)]
ixgbe: work around for DDP last buffer size
A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: Amir Hanania <amir.hanania@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Andy Gospodarek [Thu, 17 Feb 2011 09:13:13 +0000 (01:13 -0800)]
ixgbe: fix panic due to uninitialised pointer
Systems containing an 82599EB and running a backported driver from
upstream were panicing on boot. It turns out hw->mac.ops.setup_sfp is
only set for 82599, so one should check to be sure that pointer is set
before continuing in ixgbe_sfp_config_module_task. I verified by
inspection that the upstream driver has the same issue and also added a
check before the call in ixgbe_sfp_link_config.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.
This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dave Airlie [Thu, 17 Feb 2011 03:56:35 +0000 (13:56 +1000)]
Merge remote branch 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next into drm-fixes
* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
Alex Deucher [Thu, 17 Feb 2011 02:17:04 +0000 (21:17 -0500)]
drm/radeon/kms: add missing frac fb div flag for dce4+
The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+. Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.
Chuck Ebbert [Wed, 16 Feb 2011 23:11:53 +0000 (18:11 -0500)]
block: revert block_dev read-only check
This reverts commit 75f1dc0d076d ("block: check bdev_read_only() from
blkdev_get()"). That commit added stricter checking to make sure
devices that were being used read-only were actually opened in that
mode.
It turns out that the change breaks a bunch of kernel code that opens
block devices. Affected systems include dm, md, and the loop device.
Because strict checking for read-only opens of block devices was not
done before this, the code that opens the devices was opening them
read-write even if they were being used read-only. Auditing all that
code will take time, and new userspace packages for dm, mdadm, etc.
will also be required.
Ben Skeggs [Mon, 7 Feb 2011 00:49:39 +0000 (10:49 +1000)]
drm/nv40: fix tiling-related setup for a number of chipsets
Due to the default case handling the older chipsets, a bunch of the newer
ones ended up having the wrong tiling regs used. This commit switches the
default case to handle the newest chipsets.
This also makes nv4e touch the "extra" tiling regs. "nv" doesn't touch
them for C51 but traces of the NVIDIA binary driver show it being done
there.
I couldn't find NV41/NV45 traces to confirm the behaviour there, but an
educated guess was taken at each of them.
Francisco Jerez [Thu, 3 Feb 2011 00:53:18 +0000 (01:53 +0100)]
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
Reported-by: Alex Buell <alex.buell@munted.org.uk> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Francisco Jerez [Thu, 3 Feb 2011 00:49:33 +0000 (01:49 +0100)]
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
Reported-by: Alex Buell <alex.buell@munted.org.uk> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@kernel.org Reported-by: Herbert Poetzl <herbert@13thfloor.at> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
PM / Hibernate: Return error code when alloc_image_page() fails
Currently we return 0 in swsusp_alloc() when alloc_image_page() fails.
Fix that. Also remove unneeded "error" variable since the only
useful value of error is -ENOMEM.
[rjw: Fixed up the changelog and changed subject.]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Cc: stable@kernel.org Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tejun Heo [Wed, 16 Feb 2011 17:10:19 +0000 (18:10 +0100)]
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
MAYDAY_INITIAL_TIMEOUT is defined as HZ / 100 and depending on
configuration may end up 0 or 1. Even when it's 1, depending on when
the mayday timer is added in the current jiffy interval, it may expire
way before a jiffy has passed.
Make sure MAYDAY_INITIAL_TIMEOUT is at least two to guarantee that at
least a full jiffy has passed before calling rescuers.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Ray Jui <rjui@broadcom.com> Cc: stable@kernel.org
Linus Torvalds [Wed, 16 Feb 2011 16:56:55 +0000 (08:56 -0800)]
vfs: fix BUG_ON() in fs/namei.c:1461
When Al moved the nameidata_dentry_drop_rcu_maybe() call into the
do_follow_link function in commit 844a391799c2 ("nothing in
do_follow_link() is going to see RCU"), he mistakenly left the
BUG_ON(inode != path->dentry->d_inode);
behind. Which would otherwise be ok, but that BUG_ON() really needs to
be _after_ dropping RCU, since the dentry isn't necessarily stable
otherwise.
So complete the code movement in that commit, and move the BUG_ON() into
do_follow_link() too. This means that we need to pass in 'inode' as an
argument (just for this one use), but that's a small thing. And
eventually we may be confident enough in our path lookup that we can
just remove the BUG_ON() and the unnecessary inode argument.
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Wed, 16 Feb 2011 08:25:31 +0000 (09:25 +0100)]
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Dmitry Torokhov <dtor@mail.ru> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Alex Dubov <oakad@yahoo.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Steven Whitehouse <swhiteho@redhat.com>
Linus Torvalds [Wed, 16 Feb 2011 01:51:18 +0000 (17:51 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
Greg Ungerer [Tue, 8 Feb 2011 04:40:44 +0000 (14:40 +1000)]
m68knommu: fix mis-named variable int set_irq_chip loop
Compiling for 68360 targets gives:
CC arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in
Greg Ungerer [Thu, 3 Feb 2011 11:58:39 +0000 (21:58 +1000)]
m68knommu: add optimize memmove() function
Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).
This also goes part of the way to fixing a regression caused by commit ea61bc461d09e8d331a307916530aaae808c72a2 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Greg Ungerer [Thu, 3 Feb 2011 11:31:20 +0000 (21:31 +1000)]
m68k: remove arch specific non-optimized memcmp()
The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.
This also goes part of the way to fixing a regression caused by commit ea61bc461d09e8d331a307916530aaae808c72a2 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Linus Torvalds [Tue, 15 Feb 2011 23:25:33 +0000 (15:25 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: hopefully fix pll issues for real (v3)
drm/radeon/kms: add bounds checking to avivo pll algo
drm: fix wrong usages of drm_device in DRM Developer's Guide
drm/radeon/kms: fix a few more atombios endian issues
drm/radeon/kms: improve 6xx/7xx CS error output
drm/radeon/kms: check AA resolve registers on r300
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
drm/radeon/kms: evergreen/ni big endian fixes (v2)
drm/radeon/kms: 6xx/7xx big endian fixes
drm/radeon/kms: atombios big endian fixes
drm/radeon: 6xx/7xx non-kms endian fixes
drm/radeon/kms: optimize CS state checking for r100->r500
drm: do not leak kernel addresses via /proc/dri/*/vma
drm/radeon/kms: add connector table for mac g5 9600
radeon mkregtable: Add missing fclose() calls
drm/radeon/kms: fix interlaced modes on dce4+
drm/radeon: fix memory debugging since d961db75ce86a84f1f04e91ad1014653ed7d9f46
...
Linus Torvalds [Tue, 15 Feb 2011 23:25:11 +0000 (15:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
pci: use security_capable() when checking capablities during config space read
Andrea Arcangeli [Tue, 15 Feb 2011 18:02:45 +0000 (19:02 +0100)]
thp: prevent hugepages during args/env copying into the user stack
Transparent hugepages can only be created if rmap is fully
functional. So we must prevent hugepages to be created while
is_vma_temporary_stack() is true.
This also optmizes away some harmless but unnecessary setting of
khugepaged_scan.address and it switches some BUG_ON to VM_BUG_ON.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 15 Feb 2011 23:19:45 +0000 (15:19 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / Video: Probe for output switch method when searching video devices.
ACPI / Wakeup: Enable button GPEs unconditionally during initialization
ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)
projects / linux-beck.git / log