David Howells [Fri, 23 Sep 2016 11:39:23 +0000 (12:39 +0100)]
rxrpc: Need to start the resend timer on initial transmission
When a DATA packet has its initial transmission, we may need to start or
adjust the resend timer. Without this we end up relying on being sent a
NACK to initiate the resend.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 23 Sep 2016 13:04:38 +0000 (14:04 +0100)]
rxrpc: Use before_eq() and friends to compare serial numbers
before_eq() and friends should be used to compare serial numbers (when not
checking for (non)equality) rather than casting to int, subtracting and
checking the result.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 23 Sep 2016 11:39:23 +0000 (12:39 +0100)]
rxrpc: Don't send an ACK at the end of service call response transmission
Don't send an IDLE ACK at the end of the transmission of the response to a
service call. The service end resends DATA packets until the client sends an
ACK that hard-acks all the send data. At that point, the call is complete.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 23 Sep 2016 12:17:33 +0000 (13:17 +0100)]
rxrpc: Preset timestamp on Tx sk_buffs
Set the timestamp on sk_buffs holding packets to be transmitted before
queueing them because the moment the packet is on the queue it can be seen
by the retransmission algorithm - which may see a completely random
timestamp.
If the retransmission algorithm sees such a timestamp, it may retransmit
the packet and, in future, tell the congestion management algorithm that
the retransmit timer expired.
Signed-off-by: David Howells <dhowells@redhat.com>
Colin Ian King [Thu, 22 Sep 2016 17:48:58 +0000 (18:48 +0100)]
cxgb4: fix signed wrap around when decrementing index idx
Change predecrement compare to post decrement compare to avoid an
unsigned integer wrap-around comparison when decrementing idx in
the while loop.
For example, when idx is zero, the current situation will
predecrement idx in the while loop, wrapping idx to the maximum
signed integer and cause out of bounds reads on rxq_info->msix_tbl[idx].
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series further enhances the SRIOV TC offloads of mlx5 to handle
the TC vlan push and pop actions. This serves a common use-case in
virtualization systems where the virtual switch add (push) vlan tags
to packets sent from VMs and removes (pop) vlan tags before the packet
is received by the VM. We use the new E-Switch switchdev mode and the
TC vlan action to achieve that also in SW defined SRIOV environments by
offloading TC rules that contain this action along with forwarding
(TC mirred/redirect action) the packet.
In the first patch we add some helpers to access the TC vlan action info
by offloading drivers. The next five patches don't add any new functionality,
they do some refactoring and cleanups in the current code to be used next.
The seventh patch deals with supporting vlans by the mlx5 e-switch in switchdev
mode. The eighth patch does the vlan action offload from TC and the last patch
adds matching for vlans as typically required by TC flows that involve vlan
pop action.
The series was applied on top of commit 524605e "cxgb4: Convert to use simple_open()"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:49 +0000 (20:01 +0300)]
net/mlx5e: Add TC vlan match parsing
Enhance the parsing of offloaded TC rules matches to handle vlans.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:48 +0000 (20:01 +0300)]
net/mlx5e: Add TC vlan action for SRIOV offloads
Parse TC vlan actions and set the required elements to allow offloading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:47 +0000 (20:01 +0300)]
net/mlx5: E-Switch, Support VLAN actions in the offloads mode
Many virtualization systems use a policy under which a vlan tag is
pushed to packets sent by guests, and popped before the packet is
forwarded to the VM.
The current generation of the mlx5 HW doesn't fully support that on
a per flow level. As such, we are addressing the above common use
case with the SRIOV e-Switch abilities to push vlan into packets
sent by VFs and pop vlan from packets forwarded to VFs.
The HW can match on the correct vlan being present in packets
forwarded to VFs (eSwitch steering is done before stripping
the tag), so this part is offloaded as is.
A common practice for vlans is to avoid both push vlan and pop vlan
for inter-host VM/VM (east-west) communication because in this case,
push on egress cancels out with pop on ingress.
For supporting that, we use a global eswitch vlan pop policy, hence
allowing guest A to communicate with both remote VM B and local VM C.
This works since the HW pops the vlan only if it exists (e.g for
C --> A packets but not for B --> A packets).
On the slow path, when a VF vport has an offloaded flow which involves
pushing vlans, wheres another flow is not currently offloaded, the
packets from the 2nd flow seen by the VF representor on the host have
vlan. The VF rep driver removes such vlan before calling into the host
networking stack.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:46 +0000 (20:01 +0300)]
net/mlx5e: Refactor retrival of skb from rx completion element (cqe)
Factor the relevant code into a static inline helper (skb_from_cqe)
doing that.
Move the call to napi_gro_receive to be carried out just
after mlx5e_complete_rx_cqe returns.
Both changes are to be used for the VF representor as well
in the next commit.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:45 +0000 (20:01 +0300)]
net/mlx5: Put elements related to offloaded TC rule in one struct
Put the representors related to the source and dest vports and the
action in struct mlx5_esw_flow_attr which is used while setting the FDB rule.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:44 +0000 (20:01 +0300)]
net/mlx5: E-Switch, Allow fine tuning of eswitch vport push/pop vlan
The HW can be programmed to push vlan, pop vlan or both.
A factorization step towards using the push/pop capabilties in the
eswitch offloads mode. This patch doesn't add new functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:43 +0000 (20:01 +0300)]
net/mlx5: E-Switch, Set vport representor fields explicitly on registration
The structure we use for the eswitch vport representor (mlx5_eswitch_rep)
has some fields which are set from upper layers in the driver when they
register the rep. Use explicit setting on registration time for them and
avoid global memcpy. This patch doesn't add new functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:42 +0000 (20:01 +0300)]
net/mlx5: E-Switch, Set the vport when registering the uplink rep
Set the vport value in the PF entry to be that of the uplink so
we can use it blindly over the tc / eswitch offload code without
translating it each time we deal with the uplink representor.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 22 Sep 2016 17:01:41 +0000 (20:01 +0300)]
net_sched: act_vlan: add helper inlines to access tcf_vlan info
Needed e.g for offloading drivers to pick the relevant attributes.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 22 Sep 2016 15:58:55 +0000 (08:58 -0700)]
net_sched: sch_fq: account for schedule/timers drifts
It looks like the following patch can make FQ very precise, even in VM
or stressed hosts. It matters at high pacing rates.
We take into account the difference between the time that was programmed
when last packet was sent, and current time (a drift of tens of usecs is
often observed)
Add an EWMA of the unthrottle latency to help diagnostics.
This latency is the difference between current time and oldest packet in
delayed RB-tree. This accounts for the high resolution timer latency,
but can be different under stress, as fq_check_throttled() can be
opportunistically be called from a dequeue() called after an enqueue()
for a different flow.
sfc: check async completer is !NULL before calling
Add a NULL check before calling asynchronous MCDI completion functions
during device removal.
Fixes: 7014d7f6 ("sfc: allow asynchronous MCDI without completion function") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 23 Sep 2016 10:55:04 +0000 (06:55 -0400)]
Merge branch 'sctp-fix-gap-ack-blocks'
Marcelo Ricardo Leitner says:
====================
sctp: fix the handling of SACK Gap Ack blocks
sctp_acked() is using 32bit arithmetics on 16bits vars, via TSN_lte()
macros, which is weird and confusing.
Once the offset to ctsn is calculated, all wrapping is already handled
and thus to verify the Gap Ack blocks we can just use pure
less/big-or-equal than checks.
Also, rename gap variable to tsn_offset, so it's more meaningful, as
it doesn't point to any gap at all.
Even so, I don't think this discrepancy resulted in any practical bug.
This patch is a preparation for the next one, which will introduce
typecheck() for TSN_lte() macros and would cause a compile error here.
Suggested-by: David Laight <David.Laight@ACULAB.COM> Reported-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: improve how SSN, TSN and ASCONF serial are compared
Make it similar to time_before() macros:
- easier to understand
- make use of typecheck() to avoid working on unexpected variable types
(made the issue on previous patch visible)
- for _[lg]te versions, slighly faster, as the compiler used to generate
a sequence of cmp/je/cmp/js instructions and now it's sub/test/jle
(for _lte):
Before, for sctp_outq_sack:
if (primary->cacc.changeover_active) {
1f01: 80 b9 84 02 00 00 00 cmpb $0x0,0x284(%rcx)
1f08: 74 6e je 1f78 <sctp_outq_sack+0xe8>
u8 clear_cycling = 0;
sctp_acked() is using 32bit arithmetics on 16bits vars, via TSN_lte()
macros, which is weird and confusing.
Once the offset to ctsn is calculated, all wrapping is already handled
and thus to verify the Gap Ack blocks we can just use pure
less/big-or-equal than checks.
Also, rename gap variable to tsn_offset, so it's more meaningful, as
it doesn't point to any gap at all.
Even so, I don't think this discrepancy resulted in any practical bug.
This patch is a preparation for the next one, which will introduce
typecheck() for TSN_lte() macros and would cause a compile error here.
Suggested-by: David Laight <David.Laight@ACULAB.COM> Reported-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 18 Sep 2016 22:52:20 +0000 (15:52 -0700)]
net_sched: check NULL on error path in route4_change()
On error path in route4_change(), 'f' could be NULL,
so we should check NULL before calling tcf_exts_destroy().
Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()") Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Thu, 22 Sep 2016 08:36:15 +0000 (16:36 +0800)]
net: ethernet: mediatek: remove superfluous local variable for phy address
remove the unused variable for parsing PHY address
and the related logic for sanity test which would
be all already handled done when of_mdiobus_register
was called
Reported-by: Nelson Chang <nelson.chang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Sep 2016 12:21:28 +0000 (08:21 -0400)]
Merge branch 'mediatek-trgmii'
Sean Wang says:
====================
mediatek: add support for RGMII on GMAC0 through TRGMII hardware module
By default, GMAC0 is connected to built-in switch called
MT7530 through the proprietary interface called Turbo RGMII
(TRGMII). TRGMII also supports well for RGMII as generic external
PHY uses but requires some slight changes to the setup of TRGMII
and doesn't have well support on current driver.
So this patchset
1) provides the slight changes of the setup for RGMII can work
through TRGMII
2) adds additional setting "trgmii" as PHY_INTERFACE_MODE_TRGMII
about phy-mode on device tree to make GMAC0 distinguish which
mode it runs
3) changes dynamically source clock, TX/RX delay and interface
mode on TRGMII for adapting various link
Changes since v1:
- fixed the style of comment which doesn't have a space at
the beginning and end of comment lines
- add support for phy-mode "trgmii" as PHY_INTERFACE_MODE_TRGMII
into linux/phy.h
- enhance the Documentation about device tree binding for trgmii
which is applicable only for GMAC0 which uses fixed-link
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Thu, 22 Sep 2016 02:33:55 +0000 (10:33 +0800)]
net: ethernet: mediatek: add support for GMAC0 connecting with external PHY through TRGMII
Changing dynamically source clock, TX/RX delay and interface mode
used by TRGMII hardware module inside PHY capability polling routine
for adapting to the various speed of RGMII used by external PHY for
GMAC0.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Thu, 22 Sep 2016 02:33:54 +0000 (10:33 +0800)]
net: ethernet: mediatek: add extension of phy-mode for TRGMII
adds PHY-mode "trgmii" as an extension for the operation
mode of the PHY interface for PHY_INTERFACE_MODE_TRGMII.
and adds a variable trgmii inside mtk_mac as the indication
to make the difference between the MAC connected to internal
switch or connected to external PHY by the given configuration
on the board and then to perform the corresponding setup on
TRGMII hardware module.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Sep 2016 12:14:59 +0000 (08:14 -0400)]
Merge tag 'rxrpc-rewrite-20160922-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Preparation for slow-start algorithm [ver #2]
Here are some patches that prepare for improvements in ACK generation and
for the implementation of the slow-start part of the protocol:
(1) Stop storing the protocol header in the Tx socket buffers, but rather
generate it on the fly. This potentially saves a little space and
makes it easier to alter the header just before transmission (the
flags may get altered and the serial number has to be changed).
(2) Mask off the Tx buffer annotations and add a flag to record which ones
have already been resent.
(3) Track RTT on a per-peer basis for use in future changes. Tracepoints
are added to log this.
(4) Send PING ACKs in response to incoming calls to elicit a PING-RESPONSE
ACK from which RTT data can be calculated. The response also carries
other useful information.
(5) Expedite PING-RESPONSE ACK generation from sendmsg. If we're actively
using sendmsg, this allows us, under some circumstances, to avoid
having to rely on the background work item to run to generate this
ACK.
This requires ktime_sub_ms() to be added.
(6) Set the REQUEST-ACK flag on some DATA packets to elicit ACK-REQUESTED
ACKs from which RTT data can be calculated.
(7) Limit the use of pings and ACK requests for RTT determination.
Changes:
(V2) Don't use the C division operator for 64-bit division. One instance
should use do_div() and the other should be using nsecs_to_jiffies().
The last two patches got transposed, leading to an undefined symbol
in one of them.
Reported-by: kbuild test robot <lkp@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 21 Sep 2016 23:29:32 +0000 (00:29 +0100)]
rxrpc: Reduce the number of PING ACKs sent
We don't want to send a PING ACK for every new incoming call as that just
adds to the network traffic. Instead, we send a PING ACK to the first
three that we receive and then once per second thereafter.
This could probably be made adjustable in future.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 21 Sep 2016 23:29:31 +0000 (00:29 +0100)]
rxrpc: Reduce the number of ACK-Requests sent
Reduce the number of ACK-Requests we set on DATA packets that we're sending
to reduce network traffic. We set the flag on odd-numbered DATA packets to
start off the RTT cache until we have at least three entries in it and then
probe once per second thereafter to keep it topped up.
This could be made tunable in future.
Note that from this point, the RXRPC_REQUEST_ACK flag is set on DATA
packets as we transmit them and not stored statically in the sk_buff.
Signed-off-by: David Howells <dhowells@redhat.com>
Since the TFO socket is accepted right off SYN-data, the socket
owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK
retransmission or timeout stats (i.e., tcpi_total_retrans,
tcpi_retransmits). Currently those stats are only updated
upon handshake completes. This patch fixes it.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes these under-accounting SNMP rtx stats
LINUX_MIB_TCPFORWARDRETRANS
LINUX_MIB_TCPFASTRETRANS
LINUX_MIB_TCPSLOWSTARTRETRANS
when retransmitting TSO packets
Fixes: 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time") Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Sep 2016 07:31:22 +0000 (03:31 -0400)]
Merge branch 'ftgmac100-ast2500-support'
Joel Stanley says:
====================
ftgmac100 support for ast2500
This series adds support to the ftgmac100 driver for the Aspeed ast2400 and
ast2500 SoCs. In particular, they ensure the driver works correctly on the
ast2500 where the MAC block has seen some changes in register layout.
They have been tested on ast2400 and ast2500 systems with the NCSI stack and
with a directly attached PHY.
V2 reworks the two patches relating to PHYSTS_CHG into the one patch that
disables the interrupt instead of playing with interrupt sensitivity. I kept
patch 4 'net/faraday: Clear stale interrupts' which was first introduced to
clear the stale PHYSTS_CHG interrupt, as it helps keep us safe from unhygienic
(vendor) bootloaders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Stanley [Wed, 21 Sep 2016 23:05:03 +0000 (08:35 +0930)]
net/faraday: Mask out PHYSTS_CHG interrupt
The PHYSTS_CHG (the ftgmac100's PHY IRQ) is telling the system to go
look at the PHY registers for a link status change.
The interrupt was causing issues on Aspeed SoC where some board designs
had an active high configuration, some active low, and in some cases
repurposed for other functions. When misconfigured Linux would chew 100%
of CPU cycles servicing interrupts:
While in the ftgmac100 IP can be configured for high, low and edge
sensitivity the current driver always polls the PHY, so we chose to mask
out the interrupt.
See https://patchwork.ozlabs.org/patch/672099/ for more discussion.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Stanley [Wed, 21 Sep 2016 23:05:02 +0000 (08:35 +0930)]
net/faraday: Configure old MDIO interface on Aspeed SoCs
The Aspeed SoCs have a new MDIO interface as an option in the G4 and G5
SoCs. The old one is still available, so select it in order to remain
compatible with the ftgmac100 driver.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
There is stale interrupt (PHYSTS_CHG in ISR, bit#6 in 0x0) from
the bootloader (uboot) when enabling the MAC. The stale interrupts
aren't part of kernel and should be cleared.
This clears the stale interrupts in ISR (0x0) when enabling the MAC.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Stanley [Wed, 21 Sep 2016 23:05:00 +0000 (08:35 +0930)]
net/faraday: Adapt for Aspeed SoCs
The RXDES and TXDES registers bits in the ftgmac100 indicates EDO{R,T}R
at bit position 15 for the Faraday Tech IP. However, the version of this
IP present in the Aspeed SoCs has these bits at position 30 in the
registers.
It appers that ast2400 SoCs support both positions, with the 15th bit
marked as reserved but still functional. In the ast2500 this bit is
reused for another function, so we need a work around.
This was confirmed with engineers from Aspeed that using bit 30 is
correct for both the ast2400 and ast2500 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Jeffery [Wed, 21 Sep 2016 23:04:59 +0000 (08:34 +0930)]
net/faraday: Make EDO{R,T}R bits configurable
These bits are #defined at a fixed location. In order to support future
hardware that has chosen to move these bits around move the bits into a
member of the struct ftgmac100.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Jeffery [Wed, 21 Sep 2016 23:04:58 +0000 (08:34 +0930)]
net/faraday: Separate rx page storage from rxdesc
The ftgmac100 hardware revision in e.g. the Aspeed AST2500 no longer
reserves all bits in RXDES#2 but instead uses the bottom 16 bits to
store MAC frame metadata. Avoid corruption by shifting struct page
pointers out to their own member in struct ftgmac100.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 21 Sep 2016 23:29:31 +0000 (00:29 +0100)]
rxrpc: Obtain RTT data by requesting ACKs on DATA packets
In addition to sending a PING ACK to gain RTT data, we can set the
RXRPC_REQUEST_ACK flag on a DATA packet and get a REQUESTED-ACK ACK. The
ACK packet contains the serial number of the packet it is in response to,
so we can look through the Tx buffer for a matching DATA packet.
This requires that the data packets be stamped with the time of
transmission as a ktime rather than having the resend_at time in jiffies.
This further requires the resend code to do the resend determination in
ktimes and convert to jiffies to set the timer.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 21 Sep 2016 23:29:31 +0000 (00:29 +0100)]
rxrpc: Expedite ping response transmission
Expedite the transmission of a response to a PING ACK by sending it from
sendmsg if one is pending. We're most likely to see a PING ACK during the
client call Tx phase as the other side may use it to determine a number of
parameters, such as the client's receive window size, the RTT and whether
the client is doing slow start (similar to RFC5681).
If we don't expedite it, it's left to the background processing thread to
transmit.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 21 Sep 2016 23:29:31 +0000 (00:29 +0100)]
rxrpc: Send pings to get RTT data
Send a PING ACK packet to the peer when we get a new incoming call from a
peer we don't have a record for. The PING RESPONSE ACK packet will tell us
the following about the peer:
(1) its receive window size
(2) its MTU sizes
(3) its support for jumbo DATA packets
(4) if it supports slow start (similar to RFC 5681)
(5) an estimate of the RTT
This is necessary because the peer won't normally send us an ACK until it
gets to the Rx phase and we send it a packet, but we would like to know
some of this information before we start sending packets.
A pair of tracepoints are added so that RTT determination can be observed.
Signed-off-by: David Howells <dhowells@redhat.com>
David S. Miller [Thu, 22 Sep 2016 07:13:39 +0000 (03:13 -0400)]
Merge branch 'sctp-align'
Marcelo Ricardo Leitner says:
====================
Rename WORD_TRUNC/ROUND macros and use them
This patchset aims to rename these macros to a non-confusing name, as
reported by David Laight and David Miller, and to update all remaining
places to make use of it, which was 1 last remaining spot.
v3:
- Name it SCTP_PAD4 instead of SCTP_ALIGN4, as suggested by David Laight
v2:
- fixed 2nd patch summary
Details on the specific changelogs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To something more meaningful these days, specially because this is
working on packet headers or lengths and which are not tied to any CPU
arch but to the protocol itself.
So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4.
Reported-by: David Laight <David.Laight@ACULAB.COM> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Sep 2016 06:51:48 +0000 (02:51 -0400)]
Merge branch 'mlx5e-xdp'
Tariq Toukan says:
====================
mlx5e XDP support
This series adds XDP support in mlx5e driver.
This includes the use cases: XDP_DROP, XDP_PASS, and XDP_TX.
Single stream performance tests show 16.5 Mpps for XDP_DROP,
and 12.4 Mpps for XDP_TX, with nice scalability for multiple streams/rings.
This rate of XDP_DROP is lower than the 32 Mpps we got in previous
implementation, when Striding RQ was used.
We moved to non-Striding RQ, as some XDP_TX requirements (like headroom,
packet-per-page) cannot be satisfied with the current Striding RQ HW,
and we decided to fully support both DROP/TX.
Few directions are considered in order to enable the faster rate for XDP_DROP,
e.g a possibility for users to enable Striding RQ so they choose optimized
XDP_DROP on the price of partial XDP_TX functionality, or some HW changes.
Series generated against net-next commit: cf714ac147e0 'ipvlan: Fix dependency issue'
Thanks,
Tariq
V2:
* patch 8:
- when XDP_TX fails, call mlx5e_page_release and drop the packet.
- update xdp_tx counter within mlx5e_xmit_xdp_frame.
(mlx5e_xmit_xdp_frame return value becomes obsolete, change it to void)
- drop the packet for unknown XDP return code.
* patch 9:
- use a boolean for xdp_doorbell in SQ struct, instead of dragging it
throughout the functions calls.
- handle doorbell and counters within mlx5e_xmit_xdp_frame.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
*My xmitter was limited to 36.3Mpps, so it is the bottleneck.
It seems that receive side can handle more.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for XDP_TX forwarding from xdp program.
Using XDP, now user can loop packets out of the same port.
We create a dedicated TX SQ for each channel that will serve
XDP programs that return XDP_TX action to loop packets back to
the wire directly from the channel RQ RX path.
For that RX pages will now need to be mapped bi-directionally,
and on XDP_TX action we will sync the page back to device then
queue it into SQ for transmission. The XDP xmit frame function will
report back to the RX path if the page was consumed (transmitted), if so,
RX path will forget about that page as if it were released to the stack.
Later on, on XDP TX completion, the page will be released back to the
page cache.
For simplicity this patch will hit a doorbell on every XDP TX packet.
Next patch will introduce a xmit more like mechanism that will
queue up more than one packet into SQ w/o notifying the hardware,
once RX napi loop is done we will hit doorbell once for all XDP TX
packets form the previous loop. This should drastically improve
XDP TX performance.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Have a clear separation between different SQ types
Make a clear separate between Regular SQ (TXQ) and ICO SQ creation,
destruction and union their mutual information structures.
Don't allocate redundant TXQ skb/wqe_info/dma_fifo arrays for ICO SQ.
And have a different SQ edge for ICO SQ than TXQ SQ, to be more
accurate.
In preparation for XDP TX support.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BPF_PROG_TYPE_PHYS_DEV hook in mlx5e driver.
When XDP is on we make sure to change channels RQs type to
MLX5_WQ_TYPE_LINKED_LIST rather than "striding RQ" type to
ensure "page per packet".
On XDP set, we fail if HW LRO is set and request from user to turn it
off. Since on ConnectX4-LX HW LRO is always on by default, this will be
annoying, but we prefer not to enforce LRO off from XDP set function.
Full channels reset (close/open) is required only when setting XDP
on/off.
When XDP set is called just to exchange programs, we will update
each RQ xdp program on the fly and for synchronization with current
data path RX activity of that RQ, we temporally disable that RQ and
ensure RX path is not running, quickly update and re-enable that RQ,
for that we do:
- rq.state = disabled
- napi_synnchronize
- xchg(rq->xdp_prg)
- rq.state = enabled
- napi_schedule // Just in case we've missed an IRQ
Packet rate performance testing was done with pktgen 64B packets and on
TX side and, TC drop action on RX side compared to XDP fast drop.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Comparison is done between:
1. Baseline, Before this patch with TC drop action
2. This patch with TC drop action
3. This patch with XDP RX fast drop
RX Cores Baseline(TC drop) TC drop XDP fast Drop
--------------------------------------------------------------
1 5.3Mpps 5.3Mpps 16.5Mpps
2 10.2Mpps 10.2Mpps 31.3Mpps
4 20.5Mpps 19.9Mpps 36.3Mpps*
*My xmitter was limited to 36.3Mpps, so it is the bottleneck.
It seems that receive side can handle more.
Signed-off-by: Rana Shahout <ranas@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add two helper functions to allow dynamic changes of RQ type.
mlx5e_set_rq_priv_params and mlx5e_set_rq_type_params will be
used on netdev creation to determine the default RQ type.
This will be needed later for downstream patches of XDP support.
When enabling XDP we will dynamically move from striding RQ to
linked list RQ type.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch LRO size was 64K, now with build_skb requires
extra room, headroom + sizeof(skb_shared_info) added to the data
buffer will make wqe size or page_frag_size slightly larger than
64K which will demand order 5 page instead of order 4 in 4K page systems.
We take those extra bytes from hardware LRO data size in order to not
increase the required page order for when hardware LRO is enabled.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We have two types of RX RQs, and they use two separate sets of
info arrays and structures in RX data path function. Today those
structures are mutually exclusive per RQ type, hence one kind is
allocated on RQ creation according to the RQ type.
For better cache locality and to minimalize the
sizeof(struct mlx5e_rq), in this patch we define them as a union.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For non-striding RQ configuration before this patch we had a ring
with pre-allocated SKBs and mapped the SKB->data buffers for
device.
For robustness and better RX data buffers management, we allocate a
page per packet and build_skb around it.
This patch (which is a prerequisite for XDP) will actually reduce
performance for normal stack usage, because we are now hitting a bottleneck
in the page allocator. We use the page-cache to restore or even improve
performance in comparison to the old RX scheme.
Packet rate performance testing was done with pktgen 64B packets on xmit
side and TC ingress dropping action on RX side.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Comparison is done between:
1.Baseline, before 'net/mlx5e: Build RX SKB on demand'
2.Build SKB with RX page cache (This patch)
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 21 Sep 2016 05:45:58 +0000 (22:45 -0700)]
tcp: implement TSQ for retransmits
We saw sch_fq drops caused by the per flow limit of 100 packets and TCP
when dealing with large cwnd and bursts of retransmits.
Even after increasing the limit to 1000, and even after commit 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time"),
we can still have these drops.
Under certain conditions, TCP can spend a considerable amount of
time queuing thousands of skbs in a single tcp_xmit_retransmit_queue()
invocation, incurring latency spikes and stalls of other softirq
handlers.
This patch implements TSQ for retransmits, limiting number of packets
and giving more chance for scheduling packets in both ways.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 21 Sep 2016 03:33:15 +0000 (23:33 -0400)]
MAINTAINERS: Update b44 maintainer.
Taking over as maintainer since Gary Zambrano is no longer working
for Broadcom.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 21 Sep 2016 01:06:17 +0000 (18:06 -0700)]
net: get rid of an signed integer overflow in ip_idents_reserve()
Jiri Pirko reported an UBSAN warning happening in ip_idents_reserve()
[] UBSAN: Undefined behaviour in ./arch/x86/include/asm/atomic.h:156:11
[] signed integer overflow:
[] -2117905507 + -695755206 cannot be represented in type 'int'
Since we do not have uatomic_add_return() yet, use atomic_cmpxchg()
so that the arithmetics can be done using unsigned int.
Fixes: 04ca6973f7c1 ("ip: make IP identifiers less predictable") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Sep 2016 06:20:16 +0000 (02:20 -0400)]
Merge branch 'mv88e6390-prep'
Andrew Lunn says:
====================
Preparation for mv88e6390
These two patches are a couple of preparation steps for supporting the
the MV88E6390 family of chips. This is a new generation from Marvell,
and will need more feature flags than are currently available in an
unsigned long. Expand to an unsigned long long. The MV88E6390 also
places its port registers somewhere else, so add a wrapper around port
register access.
v2:
Rework wrappers to use mv88e6xxx_{read|write}
Simpliy some (err < ) to (err)
Add Reviewed by tag.
Andrew Lunn [Tue, 20 Sep 2016 23:40:32 +0000 (01:40 +0200)]
net: dsa: mv88e6xxx: Convert flag bits to unsigned long long
We are soon going to run out of flag bits on 32bit systems. Convert to
unsigned long long.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 20 Sep 2016 23:40:31 +0000 (01:40 +0200)]
net: dsa: mv88e6xxx: Add helper for accessing port registers
There is a device coming soon which places its port registers
somewhere different to all other Marvell switches supported so far.
Add helper functions for reading/writing port registers, making it
easier to handle this new device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Pitre [Tue, 20 Sep 2016 23:25:58 +0000 (19:25 -0400)]
ptp_clock: future-proofing drivers against PTP subsystem becoming optional
Drivers must be ready to accept NULL from ptp_clock_register() if the
PTP clock subsystem is configured out.
This patch documents that and ensures that all drivers cope well
with a NULL return.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Eugenia Emantayev <eugenia@mellanox.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Tue, 20 Sep 2016 20:30:11 +0000 (22:30 +0200)]
net: ethernet: hisilicon: hns: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
during merge for conflicts overlapping commits by
Commit b20b378d49926b82c0a131492fa8842156e0e8a9
("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamal Heib [Tue, 20 Sep 2016 11:55:31 +0000 (14:55 +0300)]
net/mlx4_core: Fix to clean devlink resources
This patch cleans devlink resources by calling devlink_port_unregister()
to avoid the following issues:
- Kernel panic when triggering reset flow.
- Memory leak due to unfreed resources in mlx4_init_port_info().
Fixes: 09d4d087cd48 ("mlx4: Implement devlink interface") Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Sep 2016 05:40:07 +0000 (01:40 -0400)]
Merge branch 'cxgb4-tc-offload'
Rahul Lakkireddy says:
====================
cxgb4: add support for offloading TC u32 filters
This series of patches add support to offload TC u32 filters onto
Chelsio NICs.
Patch 1 moves current common filter code to separate files
in order to provide a common api for performing packet classification
and filtering in Chelsio NICs.
Patch 2 enables filters for normal NIC configuration and implements
common api for setting and deleting filters.
Patches 3-5 add support for TC u32 offload via ndo_setup_tc.
---
v3:
Based on review and suggestion from David Miller <davem@davemloft.net>
- Fixed all local variable declarations by placing them in longest line
first and shortest line last order.
v2:
Based on review and suggestions from Jiri Pirko <jiri@resnulli.us>:
- Replaced macros S and U with appropriate static helper functions.
- Moved completion code for set and delete filters to respective
functions cxgb4_set_filter() and cxgb4_del_filter(). Renamed the
original functions to __cxgb4_set_filter() and __cxgb4_del_filter()
in case synchronization is not required.
- Dropped debugfs patch.
- Merged code for inserting and deleting u32 filters into a single
patch.
- Reworked and fixed bugs with traversing the actions list.
- Removed all unnecessary extra ().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dropping matched packets in hardware. Also add support
for re-directing matched packets to a specified port in hardware.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading u32 filter onto hardware. Links are stored
in a jump table to perform necessary jumps to match TCP/UDP header.
When inserting rules in the linked bucket, the TCP/UDP match fields
in the corresponding entry of the jump table are appended to the filter
rule before insertion. If a link is deleted, then all corresponding
filters associated with the link are also deleted. Also enable
hardware tc offload as a supported feature.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: add parser to translate u32 filters to internal spec
Parse information sent by u32 into internal filter specification.
Add support for parsing several fields in IPv4, IPv6, TCP, and UDP.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: add common api support for configuring filters
Enable filters for non-offload configuration and add common api support
for setting and deleting filters in LE-TCAM region of the hardware.
IPv4 filters occupy one slot. IPv6 filters occupy 4 slots and must
be on a 4-slot boundary. IPv4 filters can not occupy a slot belonging
to IPv6 and the vice-versa is also true.
Filters are set and deleted asynchronously. Use completion to wait
for reply from firmware in order to allow for synchronization if needed.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Move common filter code to separate files. Also fix the following
checkpatch checks.
CHECK: Comparison to NULL could be written "!f->l2t"
+ if (f->l2t == NULL) {
CHECK: spaces preferred around that '/' (ctx:VxV)
+ fwr->len16_pkd = htonl(FW_WR_LEN16_V(sizeof(*fwr)/16));
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: skbuff: Coding: Use eth_type_vlan() instead of open coding it
Fix 'skb_vlan_pop' to use eth_type_vlan instead of directly comparing
skb->protocol to ETH_P_8021Q or ETH_P_8021AD.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Reviewed-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: skbuff: Remove errornous length validation in skb_vlan_pop()
In 93515d53b1
"net: move vlan pop/push functions into common code"
skb_vlan_pop was moved from its private location in openvswitch to
skbuff common code.
In case skb has non hw-accel vlan tag, the original 'pop_vlan()' assured
that skb->len is sufficient (if skb->len < VLAN_ETH_HLEN then pop was
considered a no-op).
This validation was moved as is into the new common 'skb_vlan_pop'.
Alas, in its original location (openvswitch), there was a guarantee that
'data' points to the mac_header, therefore the 'skb->len < VLAN_ETH_HLEN'
condition made sense.
However there's no such guarantee in the generic 'skb_vlan_pop'.
For short packets received in rx path going through 'skb_vlan_pop',
this causes 'skb_vlan_pop' to fail pop-ing a valid vlan hdr (in the non
hw-accel case) or to fail moving next tag into hw-accel tag.
Remove the 'skb->len < VLAN_ETH_HLEN' condition entirely:
It is superfluous since inner '__skb_vlan_pop' already verifies there
are VLAN_ETH_HLEN writable bytes at the mac_header.
Note this presents a slight change to skb_vlan_pop() users:
In case total length is smaller than VLAN_ETH_HLEN, skb_vlan_pop() now
returns an error, as opposed to previous "no-op" behavior.
Existing callers (e.g. tc act vlan, ovs) usually drop the packet if
'skb_vlan_pop' fails.
Fixes: 93515d53b1 ("net: move vlan pop/push functions into common code") Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Pravin Shelar <pshelar@ovn.org> Reviewed-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
TCA_VLAN_ACT_MODIFY allows one to change an existing tag.
It accepts same attributes as TCA_VLAN_ACT_PUSH (protocol, id,
priority).
If packet is vlan tagged, then the tag gets overwritten according to
user specified attributes.
For example, this allows user to replace a tag's vid while preserving
its priority bits (as opposed to "action vlan pop pipe action vlan push").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TCA_VLAN_ACT_MODIFY allows one to change an existing tag.
It accepts same attributes as TCA_VLAN_ACT_PUSH (protocol, id,
priority).
If packet is vlan tagged, then the tag gets overwritten according to
user specified attributes.
For example, this allows user to replace a tag's vid while preserving
its priority bits (as opposed to "action vlan pop pipe action vlan push").
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Tue, 20 Sep 2016 11:39:42 +0000 (14:39 +0300)]
net/mlx4_core: Fix deadlock when switching between polling and event fw commands
When switching from polling-based fw commands to event-based fw
commands, there is a race condition which could cause a fw command
in another task to hang: that task will keep waiting for the polling
sempahore, but may never be able to acquire it. This is due to
mlx4_cmd_use_events, which "down"s the sempahore back to 0.
During driver initialization, this is not a problem, since no other
tasks which invoke FW commands are active.
However, there is a problem if the driver switches to polling mode
and then back to event mode during normal operation.
The "test_interrupts" feature does exactly that.
Running "ethtool -t <eth device> offline" causes the PF driver to
temporarily switch to polling mode, and then back to event mode.
(Note that for VF drivers, such switching is not performed).
Fix this by adding a read-write semaphore for protection when
switching between modes.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamal Heib [Tue, 20 Sep 2016 11:39:40 +0000 (14:39 +0300)]
net/mlx4_en: Fix wrong indentation
Use tabs instead of spaces before if statement, no functional change.
Fixes: e7c1c2c46201 ("mlx4_en: Added self diagnostics test implementation") Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 21 Sep 2016 23:29:32 +0000 (00:29 +0100)]
rxrpc: Add re-sent Tx annotation
Add a Tx-phase annotation for packet buffers to indicate that a buffer has
already been retransmitted. This will be used by future congestion
management. Re-retransmissions of a packet don't affect the congestion
window managment in the same way as initial retransmissions.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 21 Sep 2016 23:29:31 +0000 (00:29 +0100)]
rxrpc: Don't store the rxrpc header in the Tx queue sk_buffs
Don't store the rxrpc protocol header in sk_buffs on the transmit queue,
but rather generate it on the fly and pass it to kernel_sendmsg() as a
separate iov. This reduces the amount of storage required.
Note that the security header is still stored in the sk_buff as it may get
encrypted along with the data (and doesn't change with each transmission).
Signed-off-by: David Howells <dhowells@redhat.com>
David S. Miller [Wed, 21 Sep 2016 23:50:15 +0000 (19:50 -0400)]
Merge branch 'bpf-hw-offload'
Jakub Kicinski says:
====================
BPF hardware offload (cls_bpf for now)
Rebased and improved.
v7:
- fix patch 4.
v6 (patch 8 only):
- explicitly check for registers >= MAX_BPF_REG;
- fix leaky error path.
v5:
- fix names of guard defines in bpf_verfier.h.
v4:
- rename parser -> analyzer;
- reorganize the analyzer patches a bit;
- use bitfield.h directly.
--- merge blurb:
In the last year a lot of progress have been made on offloading
simpler TC classifiers. There is also growing interest in using
BPF for generic high-speed packet processing in the kernel.
It seems beneficial to tie those two trends together and think
about hardware offloads of BPF programs. This patch set presents
such offload to Netronome smart NICs. cls_bpf is extended with
hardware offload capabilities and NFP driver gets a JIT translator
which in presence of capable firmware can be used to offload
the BPF program onto the card.
BPF JIT implementation is not 100% complete (e.g. missing instructions)
but it is functional. Encouragingly it should be possible to
offload most (if not all) advanced BPF features onto the NIC -
including packet modification, maps, tunnel encap/decap etc.
Example of basic tests I used:
__section_cls_entry
int cls_entry(struct __sk_buff *skb)
{
if (load_byte(skb, 0) != 0x0)
return 0;
if (load_byte(skb, 4) != 0x1)
return 0;
skb->mark = 0xcafe;
if (load_byte(skb, 50) != 0xff)
return 0;
return ~0U;
}
Above code can be compiled with Clang and loaded like this:
ethtool -K p1p1 hw-tc-offload on
tc qdisc add dev p1p1 ingress
tc filter add dev p1p1 parent ffff: bpf obj prog.o action drop
This set implements the basic transparent offload, the skip_{sw,hw}
flags and reporting statistics for cls_bpf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log