In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
in two more places. I grepped the ath tree and didn't find any others.
Cc: stable@kernel.org Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Sun, 29 May 2011 12:53:20 +0000 (15:53 +0300)]
cfg80211: don't drop p2p probe responses
Commit 0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.
However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.
Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.
Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Mon, 30 May 2011 07:15:47 +0000 (10:15 +0300)]
zd1211rw: fix to work on OHCI
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
However on USB 1.1 endpoint becomes Bulk:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the
call and changes requested pipe to interrupt type (see usb_bulk_msg).
However with usb_interrupt_msg() on bulk endpoint does not correct the
pipe type to bulk, but instead URB is submitted with interrupt type pipe.
So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint
types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes
ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw
from working with OHCI.
Fix this by detecting endpoint type and using correct endpoint/pipe types
for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right
URB type on 'EP 4 OUT'.
Cc: stable@kernel.org Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 27 May 2011 12:34:48 +0000 (15:34 +0300)]
wl12xx: fix oops in sched_scan when forcing a passive scan
Fix kernel oops when trying to use passive scheduled scans. The
reason was that in passive scans there are no SSIDs, so there was a
NULL pointer dereference.
To solve the problem, we now check the number of SSIDs provided in the
sched_scan request and only access the list if there's one or more
(ie. passive scan is not forced). We also force all the channels to
be passive by adding the IEEE80211_CHAN_PASSIVE_SCAN flag locally
before the checks in the wl1271_scan_get_sched_scan_channels()
function.
Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 27 May 2011 12:34:47 +0000 (15:34 +0300)]
wl12xx: add separate config value for DFS dwell time on sched scan
Use a different value for DFS dwell time when performing a scheduled
scan. Previously we were using the same value as for normal passive
scans. This adds some flexibility between these two different types
of passive scan.
For now we use 150 TUs for DFS channel dwell time. This may need to
be fine-tuned in the future.
Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 27 May 2011 12:34:46 +0000 (15:34 +0300)]
wl12xx: fix DFS channels handling in scheduled scan
DFS channels were never getting included in the scheduled scans,
because they always contain the passive flag as well and the call was
asking for DFS and active channels.
Fix this by ignoring the passive flag when collecting DFS channels.
Also, move the DFS channels in the channel list before the 5GHz active
channels (this was implemented in the FW differently than specified).
Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Thu, 26 May 2011 20:31:08 +0000 (21:31 +0100)]
libertas: Set command sequence number later to ensure consistency
Before this patch, the command sequence number is being set before
lbs_queue_cmd() adds the command to the queue. However, lbs_queue_cmd()
sometimes forces commands to queue-jump (e.g. CMD_802_11_WAKEUP_CONFIRM).
It currently does this without considering that sequence numbers might need
adjusting to keep things running in order.
Fix this by setting the sequence number at a later stage, just before
we're actually submitting the command to the hardware. Also fixes a
possible race where seqnum was being modified outside of the driver
lock.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Fri, 27 May 2011 17:41:33 +0000 (13:41 -0400)]
net: Kill ratelimit.h dependency in linux/net.h
Ingo Molnar noticed that we have this unnecessary ratelimit.h
dependency in linux/net.h, which hid compilation problems from
people doing builds only with CONFIG_NET enabled.
Move this stuff out to a seperate net/net_ratelimit.h file and
include that in the only two places where this thing is needed.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Ingo Molnar <mingo@elte.hu>
Eric Dumazet [Thu, 26 May 2011 17:27:11 +0000 (17:27 +0000)]
inetpeer: fix race in unused_list manipulations
Several crashes in cleanup_once() were reported in recent kernels.
Commit d6cc1d642de9 (inetpeer: various changes) added a race in
unlink_from_unused().
One way to avoid taking unused_peers.lock before doing the list_empty()
test is to catch 0->1 refcnt transitions, using full barrier atomic
operations variants (atomic_cmpxchg() and atomic_inc_return()) instead
of previous atomic_inc() and atomic_add_unless() variants.
We then call unlink_from_unused() only for the owner of the 0->1
transition.
Add a new atomic_add_unless_return() static helper
Reported-by: Arun Sharma <asharma@fb.com> Reported-by: Maximilian Engelhardt <maxi@daemonizer.de> Reported-by: Yann Dupont <Yann.Dupont@univ-nantes.fr> Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Fri, 27 May 2011 04:51:54 +0000 (04:51 +0000)]
atm: expose ATM device index in sysfs
It's currently exposed only through /proc which, besides requiring
screen-scraping, doesn't allow userspace to distinguish between two
identical ATM adapters with different ATM indexes. The ATM device index
is required when using PPPoATM on a system with multiple ATM adapters.
Signed-off-by: Dan Williams <dcbw@redhat.com> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: David Woodhouse <dwmw2@infradead.org> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Chadd [Thu, 26 May 2011 17:08:04 +0000 (01:08 +0800)]
ath9k: Fix AR9287 calibration
The AR9287 calibration code was not being called because of an
incorrect MAC revision check.
This forced the AR9287 to use the AR9285 initial calibration code and
bypass the AR9287 code entirely.
Signed-off-by: Adrian Chadd <adrian@freebsd.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tao Ma [Wed, 25 May 2011 01:44:05 +0000 (09:44 +0800)]
wireless: Default to 'n' for 2 new added devices in Kconfig.
We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.
Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hans Schillstrom [Tue, 24 May 2011 12:11:05 +0000 (14:11 +0200)]
IPVS: bug in ip_vs_ftp, same list heaad used in all netns.
When ip_vs was adapted to netns the ftp application was not adapted
in a correct way.
However this is a fix to avoid kernel errors. In the long term another solution
might be chosen. I.e the ports that the ftp appl, uses should be per netns.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
mac80211: stop queues before rate control updation
Stop tx queues before updating rate control to ensure
proper rate selection. Otherwise packets can be transmitted
in 40 Mhz whereas hw is configured in HT20.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: set 40 Mhz rate only if hw is configured in ht40
Whenever there is a channel width change from 40 Mhz to 20 Mhz,
the hardware is reconfigured to ht20. Meantime before doing
the rate control updation, the packets are being transmitted are
selected rate with IEEE80211_TX_RC_40_MHZ_WIDTH.
While transmitting ht40 rate packets in ht20 mode is causing
baseband panic with AR9003 based chips.
ath9k_hw: disable phy restart on baseband panic caused by RXSM
While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Thu, 19 May 2011 23:04:46 +0000 (01:04 +0200)]
b43: N-PHY: initialize last var in calibration function
Reported-by: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 19 May 2011 16:48:45 +0000 (11:48 -0500)]
rtlwifi: Use order 2 RX buffer allocation only if necessary
Although a previous fix handles the kernel panics that result from
failure to allocate a new RX buffer, memory fragmentation can be
reduced if the amsdu_8k capability is disabled as new buffers need only
be of O(0), not O(2).
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 19 May 2011 15:17:04 +0000 (10:17 -0500)]
rtlwifi: Fix kernel panic resulting from RX buffer allocation failure
To handle amsdu_8k capability, the PCI routine of this driver must
allocate receive buffers of order 2. Under heavy load, this causes
fragmentation of memory. The present code releases the current buffer
before checking to see if a new one is availble. Recovery from
allocation failures is not possible, which results in kernel panics.
The fix is to reorder the code to check that a new buffer can be
allocated before the old one is released. If not possible, the
received frame is dropped and the old one is reused. Without this
change, it is impossible to transfer a 2 GB file without a kernel panic.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [2.6.{37,38,39}] Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Wed, 18 May 2011 21:43:38 +0000 (00:43 +0300)]
nl80211: fix check for valid SSID size in scan operations
In both trigger_scan and sched_scan operations, we were checking for
the SSID length before assigning the value correctly. Since the
memory was just kzalloc'ed, the check was always failing and SSID with
over 32 characters were allowed to go through.
This was causing a buffer overflow when copying the actual SSID to the
proper place.
This bug has been there since 2.6.29-rc4.
Cc: stable@kernel.org Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
While decoding received event packet from firmware, 4 bytes
of interface header are already removed unconditionally.
So for handling event only 4 more bytes needs to be pulled.
This is achieved by changing event header length to 4.
Almost all the events, except BA stream related and AMSDU
aggregation control events, do not have the payload in their
event skb. Such events handling depends only on the event ID.
This event ID is the first four bytes of the event skb, which
is copied to a separate variable before pulling the skb header.
Hence event handling worked only for those events that didn't
have payload in event skb.
This patch fixes the broken event path of the events with
payload in their event skb without harming existing working
event path for the events without payload.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Thu, 26 May 2011 19:00:31 +0000 (15:00 -0400)]
bug.h: Move ratelimit warn interfaces to ratelimit.h
As reported by Ingo Molnar, we still have configuration combinations
where use of the WARN_RATELIMIT interfaces break the build because
dependencies don't get met.
Instead of going down the long road of trying to make it so that
ratelimit.h can get included by kernel.h or asm-generic/bug.h,
just move the interface into ratelimit.h and make users have
to include that.
Reported-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Andy Gospodarek [Wed, 25 May 2011 04:41:59 +0000 (04:41 +0000)]
bonding: cleanup module option descriptions
Weiping Pan noticed that the module option description for
xmit_hash_policy was incorrect and was nice enough to post a patch to
fix it. The text was correct, but created a line over 80 characters and
I would rather not add those. I realized I could take a few minutes and
clean up all the descriptions and things would look much better. This
is the result.
Based on patch from Weiping Pan <panweiping3@gmail.com>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Weiping Pan <panweiping3@gmail.com> Reviewed-by: Weiping Pan <panweiping3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Mattock [Mon, 23 May 2011 20:43:48 +0000 (20:43 +0000)]
net:8021q:vlan.c Fix pr_info to just give the vlan fullname and version.
The below patch removes vlan_buggyright and vlan_copyright from vlan_proto_init,
so that it prints out just the fullname of vlan and the version number.
before:
[ 30.438203] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 30.441542] All bugs added by David S. Miller <davem@redhat.com>
after:
[ 31.513910] 802.1Q VLAN Support v1.8
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> CC: Joe Perches <joe@perches.com> CC: David S. Miller <davem@davemloft.net> CC: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It occurs because we are able to change the slave configuarion of a bond while
the bond interface is down. The bonding driver initializes some data structures
only after its ndo_open routine is called. Among them is the initalization of
the alb tx and rx hash locks. So if we add or remove a slave without first
opening the bond master device, we run the risk of trying to lock/unlock a
spinlock that has garbage for data in it, which results in our above softlock.
Note that sometimes this works, because in many cases an unlocked spinlock has
the raw_lock parameter initialized to zero (meaning that the kzalloc of the
net_device private data is equivalent to calling spin_lock_init), but thats not
true in all cases, and we aren't guaranteed that condition, so we need to pass
the relevant spinlocks through the spin_lock_init function.
Fix it by moving the spin_lock_init calls for the tx and rx hashtable locks to
the ndo_init path, so they are ready for use by the bond_store_slaves path.
Change notes:
v2) Based on conversation with Jay and Nicolas it seems that the ability to
enslave devices while the bond master is down should be safe to do. As such
this is an outlier bug, and so instead we'll just initalize the errant spinlocks
in the init path rather than the open path, solving the problem. We'll also
remove the warnings about the bond being down during enslave operations, since
it should be safe
v3) Fix spelling error
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: jtluka@redhat.com CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: nicolas.2p.debian@gmail.com CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 25 May 2011 07:34:04 +0000 (07:34 +0000)]
net: hold rtnl again in dump callbacks
Commit e67f88dd12f6 (dont hold rtnl mutex during netlink dump callbacks)
missed fact that rtnl_fill_ifinfo() must be called with rtnl held.
Because of possible deadlocks between two mutexes (cb_mutex and rtnl),
its not easy to solve this problem, so revert this part of the patch.
It also forgot one rcu_read_unlock() in FIB dump_rules()
Add one ASSERT_RTNL() in rtnl_fill_ifinfo() to remind us the rule.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Patrick McHardy <kaber@trash.net> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Meelis Roos [Wed, 25 May 2011 05:43:47 +0000 (05:43 +0000)]
Add Fujitsu 1000base-SX PCI ID to tg3
This patch adds the PCI ID of Fujitsu 1000base-SX NIC to tg3 driver.
Tested to detect the card, MAC and serdes, not tested with link at the
moment since I have no fiber switch here. I did not add new constants to
the pci_ids.h header file since these constants are used only here.
Signed-off-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Wed, 25 May 2011 04:55:51 +0000 (04:55 +0000)]
bnx2x: protect sequence increment with mutex
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 25 May 2011 04:40:11 +0000 (04:40 +0000)]
sch_sfq: fix peek() implementation
Since commit eeaeb068f139 (sch_sfq: allow big packets and be fair),
sfq_peek() can return a different skb that would be normally dequeued by
sfq_dequeue() [ if current slot->allot is negative ]
Use generic qdisc_peek_dequeued() instead of custom implementation, to
get consistent result.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Jarek Poplawski <jarkao2@gmail.com> CC: Patrick McHardy <kaber@trash.net> CC: Jesper Dangaard Brouer <hawk@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Prarit Bhargava [Wed, 25 May 2011 02:12:23 +0000 (02:12 +0000)]
isdn: netjet - blacklist Digium TDM400P
[2nd try ... 1st attempt didn't make it to netdev mailing list]
A quick google search reveals that people with this card are blacklisting it
in the initramfs and in the module blacklist based on a statement that it
is unsupported. Since the older Digium is also unsupported I'm pretty
confident that this newer card is also not supported.
lspci -xxx -vv shows
04:07.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Device b100:0003
P.
----8<----
The Asterisk Voice Card, DIGIUM TDM400P is unsupported by the netjet driver.
Blacklist it like the Digium X100P/X101P card.
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ulrich Hecht [Wed, 25 May 2011 01:07:22 +0000 (01:07 +0000)]
via-velocity: don't annotate MAC registers as packed
On ARM, memory accesses through packed pointers behave in unexpected
ways in GCC releases 4.3 and higher; see https://lkml.org/lkml/2011/2/2/163
for discussion.
In this particular case, 32-bit I/O registers are accessed bytewise,
causing incorrect setting of the DMA address registers which in turn
leads to an error interrupt storm that brings the system to a halt.
Since the mac_regs structure does not need any packing anyway, this patch
simply removes the attribute to fix the issue.
Signed-off-by: Ulrich Hecht <uli@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This update happens in xenbus watch callback context and hence does not already
hold the rtnl. Take the lock as necessary.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 24 May 2011 21:48:02 +0000 (21:48 +0000)]
sctp: fix memory leak of the ASCONF queue when free asoc
If an ASCONF chunk is outstanding, then the following ASCONF
chunk will be queued for later transmission. But when we free
the asoc, we forget to free the ASCONF queue at the same time,
this will cause memory leak.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 24 May 2011 08:31:09 +0000 (08:31 +0000)]
net: make dev_disable_lro use physical device if passed a vlan dev (v2)
If the device passed into dev_disable_lro is a vlan, then repoint the dev
poniter so that we actually modify the underlying physical device.
Signed-of-by: Neil Horman <nhorman@tuxdriver.com> CC: davem@davemloft.net CC: bhutchings@solarflare.com Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 24 May 2011 08:31:08 +0000 (08:31 +0000)]
net: move is_vlan_dev into public header file (v2)
Migrate is_vlan_dev() to if_vlan.h so that core networkig can use it
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: davem@davemloft.net CC: bhutchings@solarflare.com Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 May 2011 20:15:41 +0000 (16:15 -0400)]
bug.h: Fix build with CONFIG_PRINTK disabled.
Based upon an email by Joe Perches.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Randy Dunlap [Mon, 23 May 2011 00:22:45 +0000 (17:22 -0700)]
wireless: fix fatal kernel-doc error + warning in mac80211.h
Fix new kernel-doc Error and Warning in <net/mac80211.h>:
Error(linux-2.6.39-git5/include/net/mac80211.h:550): cannot understand prototype: 'struct ieee80211_sched_scan_ies '
Warning(linux-2.6.39-git5/include/net/mac80211.h:2289): No description found for parameter 'sta'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Mon, 23 May 2011 00:16:20 +0000 (17:16 -0700)]
wireless: fix cfg80211.h new kernel-doc warnings
Fix new kernel-doc warnings in <net/cfg80211.h>:
Warning(linux-2.6.39-git5/include/net/cfg80211.h:560): No description found for parameter 'bss_param'
Warning(linux-2.6.39-git5/include/net/cfg80211.h:1555): Enum value 'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' not described in enum 'wiphy_flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 20 May 2011 18:56:18 +0000 (11:56 -0700)]
iwlagn: dbg_fixed_rate only used when CONFIG_MAC80211_DEBUGFS enabled
Fix compiling error when CONFIG_MAC80211_DEBUGFS is not enabled
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:351: error: 'struct iwl_lq_sta' has no member named 'dbg_fixed_rate'
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:1076: error: 'struct iwl_lq_sta' has no member named 'dbg_fixed_rate'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sathya Perla [Mon, 23 May 2011 20:29:09 +0000 (20:29 +0000)]
be2net: hash key for rss-config cmd not set
A non-zero, non-descript value is needed as the hash key. The hash variable was left un-initialized; but sometimes it gets a zero value
and hashing is not effective. The constant value used now (not of any significance) seems to work fine.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Orishko [Tue, 24 May 2011 05:26:13 +0000 (05:26 +0000)]
CDC NCM: release interfaces fix in unbind()
Changes:
- claim slave/data interface during bind() and release
interfaces in unbind() unconditionally
- in case of error during bind(), release claimed data
interface in the same function
- remove obsolited "*_claimed" entries from driver context
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 24 May 2011 02:06:06 +0000 (02:06 +0000)]
bnx2x: fix inverted condition
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Mon, 23 May 2011 23:15:05 +0000 (23:15 +0000)]
igmp: call ip_mc_clear_src() only when we have no users of ip_mc_list
In igmp_group_dropped() we call ip_mc_clear_src(), which resets the number
of source filters per mulitcast. However, igmp_group_dropped() is also
called on NETDEV_DOWN, NETDEV_PRE_TYPE_CHANGE and NETDEV_UNREGISTER, which
means that the group might get added back on NETDEV_UP, NETDEV_REGISTER and
NETDEV_POST_TYPE_CHANGE respectively, leaving us with broken source
filters.
To fix that, we must clear the source filters only when there are no users
in the ip_mc_list, i.e. in ip_mc_dec_group() and on device destroy.
Acked-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 May 2011 23:07:32 +0000 (23:07 +0000)]
net: use synchronize_rcu_expedited()
synchronize_rcu() is very slow in various situations (HZ=100,
CONFIG_NO_HZ=y, CONFIG_PREEMPT=n)
Extract from my (mostly idle) 8 core machine :
synchronize_rcu() in 99985 us
synchronize_rcu() in 79982 us
synchronize_rcu() in 87612 us
synchronize_rcu() in 79827 us
synchronize_rcu() in 109860 us
synchronize_rcu() in 98039 us
synchronize_rcu() in 89841 us
synchronize_rcu() in 79842 us
synchronize_rcu() in 80151 us
synchronize_rcu() in 119833 us
synchronize_rcu() in 99858 us
synchronize_rcu() in 73999 us
synchronize_rcu() in 79855 us
synchronize_rcu() in 79853 us
When we hold RTNL mutex, we would like to spend some cpu cycles but not
block too long other processes waiting for this mutex.
We also want to setup/dismantle network features as fast as possible at
boot/shutdown time.
This patch makes synchronize_net() call the expedited version if RTNL is
locked.
synchronize_rcu_expedited() typical delay is about 20 us on my machine.
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 20 us
synchronize_rcu_expedited() in 16 us
synchronize_rcu_expedited() in 20 us
synchronize_rcu_expedited() in 18 us
synchronize_rcu_expedited() in 18 us
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com> CC: Ben Greear <greearb@candelatech.com> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Rosenberg [Mon, 23 May 2011 12:17:35 +0000 (12:17 +0000)]
net: convert %p usage to %pK
The %pK format specifier is designed to hide exposed kernel pointers,
specifically via /proc interfaces. Exposing these pointers provides an
easy target for kernel write vulnerabilities, since they reveal the
locations of writable structures containing easily triggerable function
pointers. The behavior of %pK depends on the kptr_restrict sysctl.
If kptr_restrict is set to 0, no deviation from the standard %p behavior
occurs. If kptr_restrict is set to 1, the default, if the current user
(intended to be a reader via seq_printf(), etc.) does not have CAP_SYSLOG
(currently in the LSM tree), kernel pointers using %pK are printed as 0's.
If kptr_restrict is set to 2, kernel pointers using %pK are printed as
0's regardless of privileges. Replacing with 0's was chosen over the
default "(null)", which cannot be parsed by userland %p, which expects
"(nil)".
The supporting code for kptr_restrict and %pK are currently in the -mm
tree. This patch converts users of %p in net/ to %pK. Cases of printing
pointers to the syslog are not covered, since this would eliminate useful
information for postmortem debugging and the reading of the syslog is
already optionally protected by the dmesg_restrict sysctl.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Cc: James Morris <jmorris@namei.org> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Thomas Graf <tgraf@infradead.org> Cc: Eugene Teo <eugeneteo@kernel.org> Cc: Kees Cook <kees.cook@canonical.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: David S. Miller <davem@davemloft.net> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Frysinger [Mon, 23 May 2011 12:17:09 +0000 (12:17 +0000)]
net/irda: convert bfin_sir to common Blackfin UART header
No need to duplicate these defines now that the common Blackfin code has
unified these for all UART devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sat, 21 May 2011 07:48:40 +0000 (07:48 +0000)]
net: filter: Use WARN_RATELIMIT
A mis-configured filter can spam the logs with lots of stack traces.
Rate-limit the warnings and add printout of the bogus filter information.
Original-patch-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While chasing a possible net_sched bug, I found that IP fragments have
litle chance to pass a congestioned SFQ qdisc :
- Say SFQ qdisc is full because one flow is non responsive.
- ip_fragment() wants to send two fragments belonging to an idle flow.
- sfq_enqueue() queues first packet, but see queue limit reached :
- sfq_enqueue() drops one packet from 'big consumer', and returns
NET_XMIT_CN.
- ip_fragment() cancel remaining fragments.
This patch restores fairness, making sure we return NET_XMIT_CN only if
we dropped a packet from the same flow.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Patrick McHardy <kaber@trash.net> CC: Jarek Poplawski <jarkao2@gmail.com> CC: Jamal Hadi Salim <hadi@cyberus.ca> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Mon, 23 May 2011 03:36:35 +0000 (03:36 +0000)]
ehea: Fix multicast registration on semi-promiscuous mode
Ehea will not register multicast groups in phyp if the physical
interface is in promiscuous mode. But it should register if the
logical port is in promiscuous mode, but the physical port is not.
Ehea physical promiscuous mode is defined by ehea_port->promisc,
while logical port is defined by IFF_PROMISC.
So currently, if the user set the interface in promiscuous mode,
IGMP will not be registred in PHYP, and PHYP will never pass
the multicast packet to the logical port, which is bad
So, this patch just fixes it, assuring that we register in phyp
if the physical port is not on promiscuous mode.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 22 May 2011 22:23:00 +0000 (22:23 +0000)]
net: ping: cleanups ping_v4_unhash()
net/ipv4/ping.c: In function ‘ping_v4_unhash’:
net/ipv4/ping.c:140:28: warning: variable ‘hslot’ set but not used
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Vasiliy Kulikov <segoon@openwall.com> Acked-by: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 23 May 2011 17:10:44 +0000 (10:10 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: Deal with hyperthetical case of PAGE_SIZE > 2M
slub: Remove node check in slab_free
slub: avoid label inside conditional
slub: Make CONFIG_DEBUG_PAGE_ALLOC work with new fastpath
slub: Avoid warning for !CONFIG_SLUB_DEBUG
slub: Remove CONFIG_CMPXCHG_LOCAL ifdeffery
slub: Move debug handlign in __slab_free
slub: Move node determination out of hotpath
slub: Eliminate repeated use of c->page through a new page variable
slub: get_map() function to establish map of free objects in a slab
slub: Use NUMA_NO_NODE in get_partial
slub: Fix a typo in config name
Linus Torvalds [Mon, 23 May 2011 16:26:20 +0000 (09:26 -0700)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (coretemp) Fix checkpatch errors
hwmon: Remove pkgtemp driver
hwmon: (coretemp) Merge pkgtemp with coretemp
hwmon: (pmbus) Add support for Analog Devices ADM1275
hwmon: (pmbus) Support for TI UCD90xxx series Sequencer and System Health Controllers
hwmon: (pmbus) Add support for TI UCD9200 series of PWM System Controllers
hwmon: (pmbus) Use device specific function to read fan configuration
hwmon: (pmbus) Expand scope of device specific get_status function
hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers
hwmon: Driver for MAX16065 System Manager and compatibles
hwmon: (sht15) add support for CRC validation
hwmon: (sht15) add support for the status register
hwmon: (sht15) clean-up the probe function
hwmon: (sht15) general code clean-up
hwmon: Add support for MAX6642
Linus Torvalds [Mon, 23 May 2011 16:25:52 +0000 (09:25 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix sample size bit operations
perf tools: Fix ommitted mmap data update on remap
watchdog: Change the default timeout and configure nmi watchdog period based on watchdog_thresh
watchdog: Disable watchdog when thresh is zero
watchdog: Only disable/enable watchdog if neccessary
watchdog: Fix rounding bug in get_sample_period()
perf tools: Propagate event parse error handling
perf tools: Robustify dynamic sample content fetch
perf tools: Pre-check sample size before parsing
perf tools: Move evlist sample helpers to evlist area
perf tools: Remove junk code in mmap size handling
perf tools: Check we are able to read the event size on mmap
Linus Torvalds [Mon, 23 May 2011 16:12:26 +0000 (09:12 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Linus Torvalds [Mon, 23 May 2011 16:10:03 +0000 (09:10 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (36 commits)
HID: hid-multitouch: cosmetic changes, sort classes and devices
HID: hid-multitouch: class MT_CLS_STANTUM is redundant with MT_CLS_CONFIDENCE
HID: hid-multitouch: add support for Unitec panels
HID: hid-multitouch: add support for Touch International panels
HID: hid-multitouch: add support for GoodTouch panels
HID: hid-multitouch: add support for CVTouch panels
HID: hid-multitouch: add support for ActionStar panels
HID: hiddev: fix race between hiddev_disconnect and hiddev_release
HID: magicmouse: ignore 'ivalid report id' while switching modes
HID: fix a crash in hid_report_raw_event() function.
HID: hid-multitouch: add support for Elo TouchSystems 2515 IntelliTouch Plus
HID: assorted usage updates from hut 1.12
HID: roccat: fix actual/startup profile sysfs attribute in koneplus
HID: hid-multitouch: Add support for Lumio panels
HID: 'name' and 'phys' in 'struct hid_device' can never be NULL
HID: hid-multitouch: add support for Ilitek dual-touch panel
HID: picolcd: Avoid compile warning/error triggered by copy_from_user()
HID: add support for Logitech G27 wheel
HID: hiddev: fix error path in hiddev_read when interrupted
HID: add support for Sony Navigation Controller
...
Linus Torvalds [Mon, 23 May 2011 15:51:55 +0000 (08:51 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Eliminate various 'set but not used' warnings
x86, SMEP: Fix section mismatch warnings
x86, amd: Use _safe() msr access for GartTlbWlk disable code
Tejun Heo [Mon, 23 May 2011 11:24:54 +0000 (13:24 +0200)]
block: move bd_set_size() above rescan_partitions() in __blkdev_get()
02e352287a4 (block: rescan partitions on invalidated devices on
-ENOMEDIA too) relocated partition rescan above explicit bd_set_size()
to simplify condition check. As rescan_partitions() does its own bdev
size setting, this doesn't break anything; however,
rescan_partitions() prints out the following messages when adjusting
bdev size, which can be confusing.
sda: detected capacity change from 0 to 146815737856
sdb: detected capacity change from 0 to 146815737856
This patch restores the original order and remove the warning
messages.
stable: Please apply together with 02e352287a4 (block: rescan
partitions on invalidated devices on -ENOMEDIA too).
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Tony Luck <tony.luck@gmail.com> Tested-by: Tony Luck <tony.luck@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 23 May 2011 15:42:08 +0000 (08:42 -0700)]
Merge branch 'kvm-updates/2.6.40' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.40' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (131 commits)
KVM: MMU: Use ptep_user for cmpxchg_gpte()
KVM: Fix kvm mmu_notifier initialization order
KVM: Add documentation for KVM_CAP_NR_VCPUS
KVM: make guest mode entry to be rcu quiescent state
KVM: x86 emulator: Make jmp far emulation into a separate function
KVM: x86 emulator: Rename emulate_grpX() to em_grpX()
KVM: x86 emulator: Remove unused arg from emulate_pop()
KVM: x86 emulator: Remove unused arg from writeback()
KVM: x86 emulator: Remove unused arg from read_descriptor()
KVM: x86 emulator: Remove unused arg from seg_override()
KVM: Validate userspace_addr of memslot when registered
KVM: MMU: Clean up gpte reading with copy_from_user()
KVM: PPC: booke: add sregs support
KVM: PPC: booke: save/restore VRSAVE (a.k.a. USPRG0)
KVM: PPC: use ticks, not usecs, for exit timing
KVM: PPC: fix exit accounting for SPRs, tlbwe, tlbsx
KVM: PPC: e500: emulate SVR
KVM: VMX: Cache vmcs segment fields
KVM: x86 emulator: consolidate segment accessors
KVM: VMX: Avoid reading %rip unnecessarily when handling exceptions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
bnx2x: allow device properly initialize after hotplug
bnx2x: fix DMAE timeout according to hw specifications
bnx2x: properly handle CFC DEL in cnic flow
bnx2x: call dev_kfree_skb_any instead of dev_kfree_skb
net: filter: move forward declarations to avoid compile warnings
pktgen: refactor pg_init() code
pktgen: use vzalloc_node() instead of vmalloc_node() + memset()
net: skb_trim explicitely check the linearity instead of data_len
ipv4: Give backtrace in ip_rt_bug().
net: avoid synchronize_rcu() in dev_deactivate_many
net: remove synchronize_net() from netdev_set_master()
rtnetlink: ignore NETDEV_RELEASE and NETDEV_JOIN event
net: rename NETDEV_BONDING_DESLAVE to NETDEV_RELEASE
bridge: call NETDEV_JOIN notifiers when add a slave
netpoll: disable netpoll when enslave a device
macvlan: Forward unicast frames in bridge mode to lowerdev
net: Remove linux/prefetch.h include from linux/skbuff.h
ipv4: Include linux/prefetch.h in fib_trie.c
netlabel: Remove prefetches from list handlers.
drivers/net: add prefetch header for prefetch users
...
Fixed up prefetch parts: removed a few duplicate prefetch.h includes,
fixed the location of the igb prefetch.h, took my version of the
skbuff.h code without the extra parentheses etc.
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Wait properly when flushing the ail list
GFS2: Wipe directory hash table metadata when deallocating a directory
Linus Torvalds [Mon, 23 May 2011 15:20:44 +0000 (08:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-ktest
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-ktest:
ktest: Allow options to be used by other options
ktest: Create variables for the ktest config files
ktest: Reboot after each patchcheck run
ktest: Reboot to good kernel after every bisect run
ktest: If test failed due to timeout, print that
ktest: Fix post install command
perf tools: Fix ommitted mmap data update on remap
Commit eac9eacee16 "perf tools: Check we are able to read the event
size on mmap" brought a check to ensure we can read the size of the
event before dereferencing it, and do a remap otherwise to move the
buffer forward.
However that remap was ommitting all the necessary work to
update the new page offset, head, and to unmap previous pages,
etc...
To fix this, gather all the code that fetches the event in a
seperate helper which does all the necessary checks about the
header/event size and tells us anytime a remap is needed.
Paul Parsons [Fri, 13 May 2011 01:46:03 +0000 (02:46 +0100)]
apm-emulation: apm_mutex breaks ACK; remove it
apm_mutex is locked by a process (e.g. apm -s) at the start of apm_ioctl() and
remains locked while pm_suspend() is called. Any subsequent process trying to
ACK the suspend (e.g. apmd) is then blocked at the start of apm_ioctl(),
causing the suspend to be delayed for 5 seconds in apm_suspend_notifier()
while the ACK times out. In short, ACKs don't work.
The driver's data structures are sufficiently protected by assorted locks. And
pm_suspend() has its own mutex to prevent reentrancy. Consequently there is no
obvious requirement for apm_mutex, which evolved from earlier BKL calls. So
let's remove it.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
watchdog: Change the default timeout and configure nmi watchdog period based on watchdog_thresh
Before the conversion of the NMI watchdog to perf event, the
watchdog timeout was 5 seconds. Now it is 60 seconds. For my
particular application, netbooks, 5 seconds was a better
timeout. With a short timeout, we catch faults earlier and are
able to send back a panic. With a 60 second timeout, the user is
unlikely to wait and will instead hit the power button, causing
us to lose the panic info.
This change configures the NMI period to watchdog_thresh and
sets the softlockup_thresh to watchdog_thresh * 2. In addition,
watchdog_thresh was reduced to 10 seconds as suggested by Ingo
Molnar.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org> Cc: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: Don Zickus <dzickus@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Frederic Weisbecker <fweisbec@gmail.com> Link: http://lkml.kernel.org/r/1306127423-3347-4-git-send-email-msb@chromium.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20110517071642.GF22305@elte.hu>
projects / karo-tx-linux.git / log