Merge tag 'bcm63138-v4' of http://github.com/brcm/linux into next/soc
Merge "ARM: BCM: Broadcom BCM63138 support" from Florian Fainelli:
This patchset adds very minimal support for the BCM63138 SoC which is
a xDSL SoC using a dual Cortex A9 CPU complex.
* tag 'bcm63138-v4' of http://github.com/brcm/linux:
MAINTAINERS: add entry for the Broadcom BCM63xx ARM SoCs
ARM: BCM63XX: add BCM963138DVT Reference platform DTS
ARM: BCM63XX: add BCM63138 minimal Device Tree
ARM: BCM63XX: add low-level UART debug support
ARM: BCM63XX: add basic support for the Broadcom BCM63138 DSL SoC
Merge tag 'pxa3xx-ssp-name' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into next/soc
Pull "fix PXA3xx SSP naming issue" from Haojian Zhuang:
It's imported by 972a55b62 ASoC: fix pxa-ssp compiling issue under mach-mmp from v3.5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'pxa3xx-ssp-name' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
Merge tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
Pull "ARM: tegra: core SoC code changes for 3.18" from Stephen Warren:
the primary change here gets its address information from DT rather than
iomap.h. This removes one more user of iomap.h, and will help allow the
code to move to a location that can be shared between arch/arm and
arch/arm64.
An unused header file was also removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: remove unused tegra_emc.h
ARM: tegra: Initialize flow controller from DT
of: Add NVIDIA Tegra flow controller bindings
Olof Johansson [Wed, 24 Sep 2014 18:27:17 +0000 (11:27 -0700)]
Merge tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Merge "ARM: imx: SoC updates for 3.18" from Shawn Guo:
The i.MX SoC updates for 3.18:
- Add initial devicetree support for i.MX1
- Support GPT per clock source from OSC for i.MX6
- A couple of parent selection corrections for i.MX6SL clock driver
- Support more chip revision for i.MX6
- Convert pr_warning to pr_warn
- Add exclusive gate clock support
- Add BYPASS support for i.MX6 PLL clocks
- Update i.MX6 clock tree for audio use case
- A couple of VF610 clock driver updates
* tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
ARM: imx_v6_v7_defconfig updates
ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM
arm: mach-imx: Convert pr_warning to pr_warn
ARM: imx: source gpt per clk from OSC for system timer
ARM: imx: add gpt_3m clk for i.mx6qdl
ARM: imx: fix register offset of pll7_usb_host gate clock
ARM: clk-imx6sl: refine clock tree for SSI
ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver
ARM: imx6sx: add BYPASS support for PLL clocks
ARM: imx6sl: add BYPASS support for PLL clocks
ARM: imx6q: add BYPASS support for PLL clocks
ARM: imx: add an exclusive gate clock type
ARM: clk-imx6q: refine clock tree for SSI
ARM: clk-imx6q: refine clock tree for ASRC
ARM: clk-imx6sl: correct the pxp and epdc axi clock selections
ARM: clk-imx6q: refine clock tree for ESAI
ARM: clk-imx6sl: Select appropriate parents for LCDIF clocks
ARM: clk-imx6sl: Remove csi_lcdif_sels[]
ARM: imx: clk-vf610: Add USBPHY clocks
ARM: imx: add cpufreq support for i.mx6sx
...
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
When compiling with "ARCH=arm" and "allmodconfig",
with commit: 9cdc99919a95e8b54c1998b65bb1bfdabd47d27b [2/7] ARM: hisi: enable MCPM implementation
we will get:
/tmp/cc6DjYjT.s: Assembler messages:
/tmp/cc6DjYjT.s:63: Error: selected processor does not support ARM mode `ubfx r1,r0,#8,#8'
/tmp/cc6DjYjT.s:761: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:762: Error: selected processor does not support ARM mode `dsb '
/tmp/cc6DjYjT.s:769: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:775: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:776: Error: selected processor does not support ARM mode `dsb '
/tmp/cc6DjYjT.s:795: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:801: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:802: Error: selected processor does not support ARM mode `dsb '
Fix platmcpm compilation when ARMv6 is selected.
Signed-off-by: Wei Xu <xuwei5@hisilicon.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 24 Sep 2014 05:20:10 +0000 (22:20 -0700)]
Merge tag 'D01-for-3.18' of git://github.com/hisilicon/linux-hisi into next/soc
Merge "pull request for hisilicon hip04 soc and D01 board updates" from Wei Xu:
ARM: mach-hisi: Hisilicon hip04 soc and D01 board updates for 3.18
- Add the CONFIG_MCPM_QUAD_CLUSTER configuration to enlarge cluster number from 2 to 4
- Enable MCPM on HiP04 SoC
- Enable 16 cores on HiP04 SoC
- Add platform & Fabric controller devicetree binding document for HiP04 SoC
- Add hip04.dtsi & hip04-d01.dts for hip04 SoC platform and D01 board
- Enable HiP04 SoC in both hi3xxx_defconfig & multi_v7_defconfig
- Add the support of Hisilicon HiP04 debug uart
* tag 'D01-for-3.18' of git://github.com/hisilicon/linux-hisi:
ARM: debug: add HiP04 debug uart
ARM: config: enable hisilicon hip04
ARM: dts: add hip04 dts
document: dt: add the binding on HiP04
ARM: hisi: enable HiP04
ARM: hisi: enable MCPM implementation
ARM: mcpm: support 4 clusters
Olof Johansson [Wed, 24 Sep 2014 05:15:16 +0000 (22:15 -0700)]
Merge tag 'renesas-clk2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC Clk Updates for v3.18" from Simon Horman.
* Add r8a7740, sh73a0 SoCs to MSTP bindings
* tag 'renesas-clk2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
clk: shmobile: Add r8a7740, sh73a0 SoCs to MSTP bindings
Olof Johansson [Wed, 24 Sep 2014 05:04:19 +0000 (22:04 -0700)]
Merge tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC related changes for omaps for v3.18 merge window:
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
* tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (514 commits)
ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
ARM: dts: OMAP3+: Add PRM interrupt
ARM: omap: Remove stray ARCH_HAS_OPP references
ARM: DRA7: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5 / DRA7: Enable CPU RET on suspend
ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
ARM: OMAP5 / DRA7: PM: Enable Mercury retention mode on CPUx powerdomains
ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default
ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
ARM: OMAP5 / DRA7: PM: Update CPU context register offset
ARM: AM437x: use pdata quirks for pinctrl information
ARM: DRA7: use pdata quirks for pinctrl information
ARM: OMAP5: use pdata quirks for pinctrl information
ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
ARM: OMAP4+: PM: use only valid low power state for suspend
ARM: OMAP4+: PM: Make logic state programmable
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
...
Daniel Mack [Wed, 13 Aug 2014 19:59:19 +0000 (21:59 +0200)]
ARM: pxa3xx: provide specific platform_devices for all ssp ports
Currently, devices for SSP ports 1, 2 and 3 are registered as compatible
devices to pxa27x-ssp. While the actual IP core is comparable, there are
some subtle differences which users of the SSP ports address by looking at
the 'type' field.
By registering devices of type 'pxa27x-ssp', this 'type' field is
incorrectly set to PXA27x_SSP which confuses the users.
To fix this, provide specific ssp port plaform devices which use
'pxa3xx-ssp' as driver name, an instantiate them from pxa3xx.c.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Florian Fainelli [Fri, 21 Feb 2014 00:11:28 +0000 (16:11 -0800)]
ARM: BCM63XX: add BCM63138 minimal Device Tree
Add a very minimalistic BCM63138 Device Tree include file which
describes the BCM63138 SoC with only the basic set of required
peripherals:
- Cortex A9 CPUs
- ARM GIC
- ARM SCU
- PL310 Level-2 cache controller
- ARM TWD & Global timers
- ARM TWD watchdog
- legacy MIPS bus (UBUS)
- BCM6345-style UARTs (disabled by default)
Since the PL310 L2 cache controller does not come out of reset with
correct default values, we need to override the 'cache-sets' and
'cache-size' properties to get its geometry right.
Broadcom BCM63xx DSL SoCs have a different UART implementation for which
we need specially crafted low-level debug assembly code to support. Add
support for this using the standard definitions provided in
include/linux/serial_bcm63xx.h (shared with their MIPS counterparts).
Florian Fainelli [Thu, 20 Feb 2014 23:53:13 +0000 (15:53 -0800)]
ARM: BCM63XX: add basic support for the Broadcom BCM63138 DSL SoC
This patch adds basic support for the Broadcom BCM63138 DSL SoC which is
using a dual-core Cortex A9 system. Add the very minimum required code
boot Linux on this SoC.
The hotplug code contains only a single function, which is an SMP
function. Move that to platsmp.c where all other SMP runctions reside.
That allows removing hotplug.c and declaring the cpu_die function
static.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Avoid races and add synchronisation between the arch specific
kill and die routines.
The same synchronisation issue was fixed on IMX platform
by this commit:
"ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill"
(sha1: 2f3edfd7e27ad4206acbc2ae99c9df5f46353024)
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Daniel Lezcano [Tue, 2 Sep 2014 21:19:10 +0000 (14:19 -0700)]
ARM: zynq: Remove invalidate cache for cpu die
As there is no Power management unit on this board, it is not possible to power
down a core, just WFI is allowed. There is no point to invalidate the cache and
exit coherency.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Magnus Damm [Mon, 15 Sep 2014 13:35:36 +0000 (22:35 +0900)]
ARM: shmobile: r8a7794: Reserve memory as other R-Car Gen2 SoCs
Other R-Car Gen2 SoCs such as r8a7790 and r8a7791 reserve
the top 256 MiB of memory for use with CMA. Adjust the
board-less r8a7794 code to do the same.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The imx weim driver is used by some mx27/mx1 boards, so let's enable it by
default.
Generated this patch by doing:
- make imx_v4_v5_defconfig
- make menuconfig and manually select CONFIG_IMX_WEIM
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v4_v5_defconfig
ARM: imx: source gpt per clk from OSC for system timer
On i.MX6Q TO > 1.0, i.MX6DL and i.MX6SX, gpt per clock
can be from OSC instead of ipg_per, as ipg_per's rate
may be scaled when system enter low bus mode, to keep
system timer NOT drift, better to make gpt per clock
at fixed rate, here add support for gpt per clock to
be from OSC which is at fixed rate always.
There are some difference on this implementation of
gpt per clock source, see below for details:
i.MX6Q TO > 1.0: GPT_CR_CLKSRC, b'101 selects fix clock
of OSC / 8 for gpt per clk;
i.MX6DL and i.MX6SX: GPT_CR_CLKSRC, b'101 selects OSC
for gpt per clk, and we must enable GPT_CR_24MEM to
enable OSC clk source for gpt per, GPT_PR_PRESCALER24M
is for pre-scaling of this OSC clk, here set it to 8
to make gpt per clk is 3MHz;
i.MX6SL: ipg_per can be from OSC directly, so no need to
implement this new clk source for gpt per.
Add gpt_3m clock for i.mx6qdl, as gpt can source clock
from OSC, some i.MX6 series SOCs has fixed divider of
8 for gpt clock, so here add a fix clk of gpt_3m.
i.MX6Q TO1.0 has no gpt_3m option, so force it to be
from ipg_per.
ARM: imx: fix register offset of pll7_usb_host gate clock
There is a copy&paste error on register offset of pll7_usb_host gate
clock introduced by i.MX6 PLL bypass support patches. The error breaks
the ENET function, because it overwrites the pll6_enet gate bit.
Correct the offset for all i.MX6 clock drivers.
Thanks to Fugang Duan <B38611@freescale.com> for spotting the error.
Shawn Guo [Tue, 26 Aug 2014 15:06:33 +0000 (23:06 +0800)]
ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver
Since ENABLE and BYPASS bits of PLLs are now implemented as separate
gate and mux clocks by clock drivers, the code handling these two bits
can be removed from clk-pllv3 driver.
This is the same change for imx6sx clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sx.
This is the same change for imx6sl clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sl.
The imx6q clock driver currently hard-codes all PLL clocks to source
from OSC24M without BYPASS support. The patch adds the missing lvds_in
clock which is mutually exclusive with lvds_gate, and implements BYPASS
and BYPASS_CLK_SRC selection for PLL clocks as per Figure 10-3. Primary
Clock Generation in IMX6DQRM, i.e. both BYPASS_CLK_SRC and BYPASS bits
are implemented as mux clocks, and ENABLE bit of PLL clocks is
implemented as a gate clock after BYPASS mux.
Shawn Guo [Tue, 26 Aug 2014 07:06:33 +0000 (15:06 +0800)]
ARM: imx: add an exclusive gate clock type
There are a couple of gate clocks are mutually exclusive on i.MX6, i.e.
LVDSCLK1_IBEN and LVDSCLK1_OBEN. They cannot be enabled simultaneously.
This patches adds an exclusive gate clock type specifically for such
case. The clock driver will need to call imx_clk_gate_exclusive() to
register a gate clock with parameter exclusive_mask indicating the mask
of gate bits which are mutually exclusive to this gate clock.
Right now, it only handles the exclusive gate clocks which are defined
in a single hardware register, which is the case we're running into
today. But it can be extended to handle exclusive gate clocks defined
in different registers later if needed.
ARM: clk-imx6sl: correct the pxp and epdc axi clock selections
The parent clocks of IMX6SL_CLK_PXP_AXI_SEL and IMX6SL_CLK_EPDC_AXI_SEL
clocks are not the same. So split the epdc_pxp_sels into two different
clock selections 'pxp_axi_sels' and 'epdc_axi_sels'.
Shengjiu Wang [Fri, 8 Aug 2014 07:02:47 +0000 (15:02 +0800)]
ARM: clk-imx6q: refine clock tree for ESAI
There are three clock for ESAI, esai_extal, esai_ipg, esai_mem. Rename
'esai' to 'esai_extal', 'esai_ahb' to 'esai_mem', and add 'esai_ipg'.
Make the clock for ESAI more clear and align them with imx6sx.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Tue, 29 Jul 2014 14:20:28 +0000 (16:20 +0200)]
ARM: imx: clk-vf610: introduce clks_init_on
At the end of the boot process, the clock framework might disable
required main PLL's. So far, this was no issue since drivers
requested clocks, which are descended of the main PLL's (e.g.
pll1_pfd1, which provides the system clock).
To archive the full 500MHz system clock, DDR clock need to be a
descendant of PLL2 rather than PLL1 (DDRC_CLK_SEL set to 0). The
bootloader sets up the clocks accordingly before making use of
DDR at all. However, in Linux, there is no driver using PLL2,
which lead to PLL2 being disabled by the clock framework.
With this patch, we make sure that the main system clock and the
DDR clock are initially enabled and are kept enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Jason Liu [Tue, 5 Nov 2013 04:03:18 +0000 (12:03 +0800)]
ARM: i.MX6: add more chip revision support
Add more revision support for the new i.MX6DQ tape-out (TO1.5). This
TO1.5 is the Rev 1.3 as documented in i.MX6DQ data sheet, because TO1.3
and TO1.4 are never revealed.
Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
OMAP4, OMAP5 and DRA7 share a lot of common logic and data structures.
These have been enabled in the previous patches, however, this also
means that OMAP5 or DRA7 only builds also need to build OMAP4 logic.
Update to reuse OMAP4 logic.
This fixes the 'undefined reference to 'omap4_pm_init_early'' in
OMAP5 or DRA7 only builds.
Fixes: 6af16a1dac5465c ("ARM: DRA7: Add hook in SoC initcalls to enable pm initialization") Fixes: 628ed4717000789 ("ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization") Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge tag 'renesas-soc3-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Third Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
* Initial r8a7794 SoC support
* Support Cortex-A7 in shmobile_init_delay()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-soc3-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Initial r8a7794 SoC support
ARM: shmobile: support Cortex-A7 in shmobile_init_delay()
Simon Horman [Mon, 8 Sep 2014 00:27:44 +0000 (09:27 +0900)]
ARM: shmobile: r8a7740: Use SoC-specific 48-bit CMT compat string
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r8a7740 48-bit CMT
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Mon, 8 Sep 2014 00:27:48 +0000 (09:27 +0900)]
ARM: shmobile: r8a7779: Use SoC-specific TMU compat string
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r8a7779 TMU
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Mon, 8 Sep 2014 00:27:46 +0000 (09:27 +0900)]
ARM: shmobile: r8a7791: Use SoC-specific 48-bit CMT compat string
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r8a7791 48-bit CMT
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Mon, 8 Sep 2014 00:27:47 +0000 (09:27 +0900)]
ARM: shmobile: r7s72100: Use SoC-specific MTU2 compat string
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r7s72100 MTU2
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Mon, 8 Sep 2014 00:27:45 +0000 (09:27 +0900)]
ARM: shmobile: r8a7790: Use SoC-specific 48-bit CMT compat string
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r8a7790 48-bit CMT
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Mark Brown [Sat, 6 Sep 2014 10:14:16 +0000 (11:14 +0100)]
ARM: omap: Remove stray ARCH_HAS_OPP references
OPP is now a normal kernel library selected by its users rather than a
feature that architectures need to enable so ARCH_HAS_OPP serves no
function any more - remove the selects.
Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
With consolidated code, now we can add the required hooks for
OMAP5 to enable power management.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor rebase updates] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
Rajendra Nayak [Mon, 27 May 2013 10:16:44 +0000 (15:46 +0530)]
ARM: OMAP5 / DRA7: Enable CPU RET on suspend
On OMAP5 / DRA7, prevent a CPU powerdomain OFF and resulting MPU OSWR
and instead attempt a CPU RET and side effect, MPU RET in suspend.
NOTE: the hardware was originally designed to be capable of achieving
deep power states such as OFF and OSWR, however due to various issues
and risks, deepest valid state was determined to be CSWR - hence we use
the errata framework to handle this case.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: updates] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
Dont assume that all OMAP4+ code will be able to use OMAP4 hotplug
logic. On OMAP5, DRA7, we do not need this in place yet, also,
currently the CPU startup pointer is located in omap4_cpu_pm_info
instead of cpu_pm_ops.
So, isolate the function to hotplug_restart pointer in cpu_pm_ops
where it should have belonged, initalize them as per valid startup
pointers for OMAP4430/60 as in current logic, however provide
dummy_cpu_resume to be the startup location as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: split this out of original code and isolate it] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
Rajendra Nayak [Fri, 3 May 2013 10:04:40 +0000 (15:34 +0530)]
ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
Get rid of all assumptions about always having a sar base on *all*
OMAP4+ platforms. We dont need one on DRA7 and it is not necessary at
this point for OMAP5 either.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: Split and optimize] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
In addition to the standard power-management technique, the OMAP5 / DRA7
MPU subsystem also employs an SR3-APG (mercury) power management
technology to reduce leakage.
It allows for full logic and memories retention on MPU_C0 and MPU_C1 and
is controlled by the PRCM_MPU. Only "Fast-mode" is supported on the
OMAP5 and DRA7 family of processors.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor consolidation] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
Enables MPUSS ES2 power management mode using ES2_PM_MODE in
AMBA_IF_MODE register.
0x0: OMAP5 ES1 behavior, CPU cores would enter and exit OFF mode together.
Broken! Fortunately, we do not support this anymore.
0x1: OMAP5 ES2, DRA7 behavior, CPU cores are allowed to enter/exit OFF mode
independently.
This is one time settings thanks to always ON domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor conflict resolutions, consolidation for DRA7] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
With EMIF clock-domain put under hardware supervised control, memory
corruption and untraceable crashes are observed on OMAP5. Further
investigation revealed that there is a weakness in the PRCM on this
specific dynamic depedency.
The recommendation is to set MPUSS static dependency towards EMIF
clock-domain to avoid issues. This recommendation holds good for DRA7
family of devices as well.
ARM: OMAP5 / DRA7: PM: Update CPU context register offset
On OMAP5, RM_CPUi_CPUi_CONTEXT offset has changed. Update the code
so that same code works for OMAP4+ devices. DRA7 and OMAP5 have the same
context offset as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[rnayak@ti.com: for DRA7] Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: rebase, split/merge etc..] Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Tested-by: Kevin Hilman <khilman@linaro.org>
Nishanth Menon [Fri, 6 Jun 2014 06:17:37 +0000 (01:17 -0500)]
ARM: OMAP4+: PM: use only valid low power state for suspend
We are using power domain state as RET and logic state as OFF. This
state is OSWR. This may not always be supported on ALL power domains. In
fact, on certain power domains, this might result in a hang on certain
platforms. Instead, depend on powerdomain data to provide accurate
information about the supported powerdomain states and use the
appropriate function to query and use it as part of suspend path.
Nishanth Menon [Fri, 6 Jun 2014 02:40:39 +0000 (21:40 -0500)]
ARM: OMAP4+: PM: Make logic state programmable
Move the logic state as different for each power domain. This allows us
to customize the deepest power state we should target over all for each
powerdomain in the follow on patches.
Nishanth Menon [Fri, 6 Jun 2014 06:04:20 +0000 (01:04 -0500)]
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
powerdomain configuration in OMAP is done using PWRSTCTRL register for
each power domain. However, PRCM lets us write any value we'd like to
the logic and power domain target states, however the SoC integration
tends to actually function only at a few discrete states. These valid
states are already in our powerdomains_xxx_data.c file.
So, provide a function to easily query valid low power state that the
power domain is allowed to go to.
Based on work originally done by Jean Pihet <j-pihet@ti.com>
https://patchwork.kernel.org/patch/1325091/ . There is no attempt to
create a new powerdomain solution here, except fixing issues seen
attempting invalid programming attempts. Future consolidation to the
generic powerdomain framework should consider this requirement as
well.
Similar solutions have been done in product kernels in the past such
as:
https://android.googlesource.com/kernel/omap.git/+blame/android-omap-panda-3.0/arch/arm/mach-omap2/pm44xx.c
Nishanth Menon [Tue, 12 Aug 2014 12:05:19 +0000 (07:05 -0500)]
ARM: OMAP3+: PRM: register interrupt information from DT
Allow the PRM interrupt information to be picked up from device tree.
OMAP3 may use legacy boot and needs to be compatible with old dtbs
(without interrupt populated), for these, we use the value which is
pre-populated.
Nishanth Menon [Thu, 22 May 2014 20:19:29 +0000 (15:19 -0500)]
ARM: OMAP4+: PRM: register interrupt information from DT
Allow the PRM interrupt information to be picked up from device tree.
the only exception is for OMAP4 which uses values pre-populated and allows
compatibility with older dtb.