Johan Hedberg [Thu, 26 Mar 2009 14:41:56 +0000 (16:41 +0200)]
Bluetooth: Fix removing of RFCOMM DLC timer with DEFER_SETUP
There is a missing call to rfcomm_dlc_clear_timer in the case that
DEFER_SETUP is used and so the connection gets disconnected after the
timeout even if it was successfully accepted previously.
This patch adds a call to rfcomm_dlc_clear_timer to rfcomm_dlc_accept
which will get called when the user accepts the connection by calling
read() on the socket.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Herbert Xu [Fri, 17 Apr 2009 09:34:38 +0000 (02:34 -0700)]
gro: Fix use after free in tcp_gro_receive
After calling skb_gro_receive skb->len can no longer be relied
on since if the skb was merged using frags, then its pages will
have been removed and the length reduced.
This caused tcp_gro_receive to prematurely end merging which
resulted in suboptimal performance with ixgbe.
The fix is to store skb->len on the stack.
Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Fri, 17 Apr 2009 08:38:46 +0000 (01:38 -0700)]
can: Network Drop Monitor: Make use of consume_skb() in af_can.c
Since commit ead2ceb0ec9f85cff19c43b5cdb2f8a054484431 ("Network Drop
Monitor: Adding kfree_skb_clean for non-drops and modifying
end-of-line points for skbs") so called end-of-line points for skb's
should use consume_skb() to free the socket buffer.
In opposite to consume_skb() the function kfree_skb() is intended to
be used for unexpected skb drops e.g. in error conditions that now can
trigger the network drop monitor if enabled.
This patch moves the skb end-of-line point in af_can.c to use
consume_skb().
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Waling [Wed, 15 Apr 2009 23:32:11 +0000 (23:32 +0000)]
macb: process the RX ring regardless of interrupt status
Suppose that we receive lots of frames, start processing them, but
exhaust our budget so that we return before we had a chance to look
at all of them.
Then, when the network layer calls us again, we will only continue
processing the buffers if the REC bit was set in the mean time, which it
might not be if there was a brief pause in the flow of packets. If this
happens, we'll simply display a warning and call netif_rx_complete()
with potentially lots of unprocessed packets in the RX ring...
Fix this by scanning the ring no matter what flags are set in the
interrupt status register.
Signed-off-by: Erik Waling <erik.waling@konftel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Waling [Wed, 15 Apr 2009 23:32:10 +0000 (23:32 +0000)]
macb: Handle Retry Limit Exceeded errors
When transfering large amounts of data we sometimes experienced that the
Retry Limit Exceeded (RLE) bit got set in TSR during transmission
attempts. When this happened the driver would stall in a state that
prevented any more data from being sent.
Signed-off-by: Erik Waling <erik.waling@konftel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The thresholds for the DCB priority flow control are incorrect for 82599.
This fixes the thresholds to be correct.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx
is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes. This patch fixes the mapping.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Cc: stable@kernel.org Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000 transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000e transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Breeds [Thu, 16 Apr 2009 23:27:23 +0000 (16:27 -0700)]
ixgbe: Be explict with what we are !'ing in ixgbe_sfp_config_module_task()
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 16 Apr 2009 16:33:01 +0000 (18:33 +0200)]
netfilter: nf_nat: add support for persistent mappings
The removal of the SAME target accidentally removed one feature that is
not available from the normal NAT targets so far, having multi-range
mappings that use the same mapping for each connection from a single
client. The current behaviour is to choose the address from the range
based on source and destination IP, which breaks when communicating
with sites having multiple addresses that require all connections to
originate from the same IP address.
Introduce a IP_NAT_RANGE_PERSISTENT option that controls whether the
destination address is taken into account for selecting addresses.
phylib: Fix delay argument of schedule_delayed_work
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000 from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000_shutdown() from e1000_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 15 Apr 2009 10:45:08 +0000 (12:45 +0200)]
netfilter: nf_conntrack: fix crash when unloading helpers
Commit ea781f197d (netfilter: nf_conntrack: use SLAB_DESTROY_BY_RCU and)
get rid of call_rcu() was missing one conversion to the hlist_nulls
functions, causing a crash when unloading conntrack helper modules.
Reported-and-tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Patrick McHardy <kaber@trash.net>
Eric Dumazet [Wed, 15 Apr 2009 10:16:19 +0000 (12:16 +0200)]
netfilter: nf_log regression fix
commit ca735b3aaa945626ba65a3e51145bfe4ecd9e222
'netfilter: use a linked list of loggers'
introduced an array of list_head in "struct nf_logger", but
forgot to initialize it in nf_log_register(). This resulted
in oops when calling nf_log_unregister() at module unload time.
Reported-and-tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Acked-by: Eric Leblond <eric@inl.fr> Signed-off-by: Patrick McHardy <kaber@trash.net>
Markus Brunner [Wed, 15 Apr 2009 09:35:40 +0000 (02:35 -0700)]
gianfar: stop send queue before resetting gianfar
After a transmit timed out, the reset task will be called, which will free the
allocated resources(stop_gfar). If gfar_poll will be called before the
resources get allocated again gfar_clean_tx_ring will call
dev_kfree_skb_any(NULL).
ixgbe: update real_num_tx_queues on changing num_rx_queues
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 15 Apr 2009 02:48:34 +0000 (19:48 -0700)]
sfc: Use correct macro to set event bitfield
falcon_sim_phy_event() used EFX_OWORD_FIELD, which operates on
bitfields in 128-bit values, on an event, which is a 64-bit value.
This should be harmless - these macros always use little-endian
ordering, so it would read and write back the following 8 bytes
unchanged - but it is obviously wrong.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 15 Apr 2009 02:47:46 +0000 (19:47 -0700)]
sfc: Match calls to netif_napi_add() and netif_napi_del()
sfc could call netif_napi_add() multiple times for the same
napi_struct, corrupting the list of napi_structs for the associated
device and leading to a busy-loop on device removal. Move the call to
netif_napi_add() and add a call to netif_napi_del() in the obvious
places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com> Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Tue, 14 Apr 2009 22:16:55 +0000 (15:16 -0700)]
skge: fix occasional BUG during MTU change
The BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean) in skge_up()
was sometimes observed when setting MTU.
skge_down() disables the TX queue, but then reenables it by mistake via
skge_tx_clean().
Fix it by moving the waking of the queue from skge_tx_clean() to the
other caller. And to make sure start_xmit is not in progress on another
CPU, skge_down() should call netif_tx_disable().
The bug was reported to me by Jiri Jilek whose Debian system sometimes
failed to boot. He tested the patch and the bug did not happen anymore.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 14 Apr 2009 22:11:06 +0000 (15:11 -0700)]
gro: Restore correct value to gso_size
Since everybody has been focusing on baremetal GRO performance
no one noticed when I added a bug that zapped gso_size for all
GRO packets. This only gets picked up when you forward the skb
out of an interface.
Thanks to Mark Wagner for noticing this bug when testing kvm.
Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Mon, 13 Apr 2009 15:51:00 +0000 (15:51 +0000)]
ipv6:remove useless check
After switch (rthdr->type) {...},the check below is completely useless.Because:
if the type is 2,then hdrlen must be 2 and segments_left must be 1,clearly the
check is redundant;if the type is not 2,then goto sticky_done,the check is useless
too.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 14 Apr 2009 09:09:43 +0000 (02:09 -0700)]
tun: Fix crash with non-GSO users
When I made the tun driver use non-linear packets as the preferred
option, it broke non-GSO users because they would end up allocating
a completely non-linear packet, which triggers a crash when we call
eth_type_trans.
This patch reverts non-GSO users to using linear packets and adds
a check to ensure that GSO users can't cause crashes in the same
way.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan acceleration is used on receive, the vlan tag is maintained
outside of the skb data. The existing vlan tag match only works on TX
path because it uses vlan_get_tag which tests for VLAN_HW_TX_ACCEL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 13 Apr 2009 04:41:01 +0000 (04:41 +0000)]
gro: Normalise skb before bypassing GRO on netpoll VLAN path
Hi:
gro: Normalise skb before bypassing GRO on netpoll VLAN path
When we detect netpoll RX on the GRO VLAN path we bail out and
call the normal VLAN receive handler. However, the packet needs
to be normalised by calling eth_type_trans since that's what the
normal path expects (normally the GRO path does the fixup).
This patch adds the necessary call to vlan_gro_frags.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks, Signed-off-by: David S. Miller <davem@davemloft.net>
phylib: Add interrupt source check function to M88E1121R driver
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
phylib: Basic support for the M88E1121R Marvell chip
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This might work on little endian machines, but it can't on big endian
ones. You have to use the original setting mechanism to be correct on
all architectures.
The attached patch fixes parisc.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
docbook: make cleandocs
kbuild: fix spurious initramfs rebuild
Documentation: explain the difference between __bitwise and __bitwise__
kbuild: make it possible for the linker to discard local symbols from vmlinux
kbuild: remove pointless strdup() on arguments passed to new_module() in modpost
kbuild: fix a few typos in top-level Makefile
kbuild: introduce destination-y for exported headers
kbuild: use git svn instead of git-svn in setlocalversion
kconfig: fix update-po-config to accect backslash in input
kbuild: fix option processing for -I in headerdep
PM/Hibernate: Wait for SCSI devices scan to complete during resume
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add linux kernel support for YMM state
x86: fix wrong section of pat_disable & make it static
x86: Fix section mismatches in mpparse
x86: fix set_fixmap to use phys_addr_t
x86: Document get_user_pages_fast()
x86, intr-remap: fix eoi for interrupt remapping without x2apic
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/filters: return proper error code when writing filter file
tracing/filters: allow user input integer to be oct or hex
tracing/filters: fix NULL pointer dereference
tracing/filters: NIL-terminate user input filter
ftrace: Output REC->var instead of __entry->var for trace format
Make __stringify support variable argument macros too
tracing: fix document references
tracing: fix splice return too large
tracing: update file->f_pos when splice(2) it
tracing: allocate page when needed
tracing: disable seeking for trace_pipe_raw
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: continue lock debugging despite some taints
lockdep: warn about lockdep disabling after kernel taint
work_on_cpu(): rewrite it to create a kernel thread on demand
It seems that the kernel calls these acpi-cpufreq functions at a quite
high frequency.
Valdis Kletnieks also reports that this causes 70-90 forks per second on
his hardware.
Cc: Valdis.Kletnieks@vt.edu Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Zhao Yakui <yakui.zhao@intel.com> Acked-by: Dave Jones <davej@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Tested-by: Mike Galbraith <efault@gmx.de> Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Ingo Molnar <mingo@elte.hu>
[ Made it use smp_call_function_many() instead of looping over cpu's
with smp_call_function_single() - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Let new-style drivers implement attach_adapter
i2c: Fix sparse warnings for I2C_BOARD_INFO()
i2c-voodoo3: Deprecate in favor of tdfxfb
i2c-algo-pca: Fix use of uninitialized variable in debug message
When POSIX capabilities were introduced during the 2.1 Linux
cycle, the fs mask, which represents the capabilities which having
fsuid==0 is supposed to grant, did not include CAP_MKNOD and
CAP_LINUX_IMMUTABLE. However, before capabilities the privilege
to call these did in fact depend upon fsuid==0.
This patch introduces those capabilities into the fsmask,
restoring the old behavior.
See the thread starting at http://lkml.org/lkml/2009/3/11/157 for
reference.
Note that if this fix is deemed valid, then earlier kernel versions (2.4
and 2.2) ought to be fixed too.
Changelog:
[Mar 23] Actually delete old CAP_FS_SET definition...
[Mar 20] Updated against J. Bruce Fields's patch
Reported-by: Igor Zhbanov <izh1979@gmail.com> Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Cc: stable@kernel.org Cc: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: unbreak alpha percpu
mutex: have non-spinning mutexes on s390 by default
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] omap_wdt.c: move probe function to .devinit.text
[WATCHDOG] ks8695_wdt.c: move probe function to .devinit.text
[WATCHDOG] at91rm9200_wdt.c: move probe function to .devinit.text
[WATCHDOG] remove ARM26 sections
[WATCHDOG] orion5x_wdt: Add shutdown callback, use watchdog ping function
[WATCHDOG] i6300esb.c: Restructure initialization of the device
[WATCHDOG] i6300esb.c: Fix the GETSTATUS and GETBOOTSTATUS ioctls.
[WATCHDOG] i6300esb.c: Cleanup
Jean Delvare [Mon, 13 Apr 2009 15:02:14 +0000 (17:02 +0200)]
i2c: Let new-style drivers implement attach_adapter
While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
Ben Hutchings [Mon, 13 Apr 2009 15:02:14 +0000 (17:02 +0200)]
i2c: Fix sparse warnings for I2C_BOARD_INFO()
Since the first argument to I2C_BOARD_INFO() must be a string constant,
there is no need to parenthesise it, and adding parentheses results in
an invalid initialiser for char[]. gcc obviously accepts this syntax as
an extension, but sparse complains, e.g.:
drivers/net/sfc/boards.c:173:2: warning: array initialized from parenthesized string constant
Therefore, remove the parentheses.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Brian Haley [Mon, 13 Apr 2009 07:11:30 +0000 (00:11 -0700)]
Bonding: fix zero address hole bug in arp_ip_target list
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lockdep: continue lock debugging despite some taints
Impact: broaden lockdep checks
Lockdep is disabled after any kernel taints. This might be convenient
to ignore bad locking issues which sources come from outside the kernel
tree. Nevertheless, it might be a frustrating experience for the
staging developers or those who experience a warning but are focused
on another things that require lockdep.
The v2 of this patch simply don't disable anymore lockdep in case
of TAINT_CRAP and TAINT_WARN events.
lockdep: warn about lockdep disabling after kernel taint
Impact: provide useful missing info for developers
Kernel taint can occur in several situations such as warnings,
load of prorietary or staging modules, bad page, etc...
But when such taint happens, a developer might still be working on
the kernel, expecting that lockdep is still enabled. But a taint
disables lockdep without ever warning about it.
Such a kernel behaviour doesn't really help for kernel development.
This patch adds this missing warning.
Since the taint is done most of the time after the main message that
explain the real source issue, it seems safe to warn about it inside
add_taint() so that it appears at last, without hurting the main
information.
v2: Use a generic helper to disable lockdep instead of an
open coded xchg().
Marcin Slusarz [Fri, 10 Apr 2009 20:47:17 +0000 (22:47 +0200)]
x86: fix wrong section of pat_disable & make it static
pat_disable cannot be __cpuinit anymore because it's called from pat_init
and the callchain looks like this:
pat_disable [cpuinit] <- pat_init <- generic_set_all <-
ipi_handler <- set_mtrr <- (other non init/cpuinit functions)
WARNING: arch/x86/mm/built-in.o(.text+0x449e): Section mismatch in reference
from the function pat_init() to the function .cpuinit.text:pat_disable()
The function pat_init() references
the function __cpuinit pat_disable().
This is often because pat_init lacks a __cpuinit
annotation or the annotation of pat_disable is wrong.
Non CONFIG_X86_PAT version of pat_disable is static inline, so this version
can be static too (and there are no callers outside of this file).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <49DFB055.6070405@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
In arch/x86/kernel/mpparse.c, smp_reserve_bootmem() has been called
and also refers to a function which is in .init section. Thus causes
the first warning. And check_irq_src() also requires an __init,
because it refers to an .init section.
This reverts commit 5d38258ec026921a7b266f4047ebeaa75db358e5, since the
underlying problem got fixed properly in the previous commit ("async:
Fix module loading async-work regression").
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Cc: Vegard Nossum <vegard.nossum@gmail.com> Cc: Len Brown <len.brown@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several drivers use asynchronous work to do device discovery, and we
synchronize with them in the compiled-in case before we actually try to
mount root filesystems etc.
However, when compiled as modules, that synchronization is missing - the
module loading completes, but the driver hasn't actually finished
probing for devices, and that means that any user mode that expects to
use the devices after the 'insmod' is now potentially broken.
We already saw one case of a similar issue in the ACPI battery code,
where the kernel itself expected the module to be all done, and unmapped
the init memory - but the async device discovery was still running.
That got hacked around by just removing the "__init" (see commit 5d38258ec026921a7b266f4047ebeaa75db358e5 "ACPI battery: fix async boot
oops"), but the real fix is to just make the module loading wait for all
async work to be completed.
It will slow down module loading, but since common devices should be
built in anyway, and since the bug is really annoying and hard to handle
from user space (and caused several S3 resume regressions), the simple
fix to wait is the right one.
This fixes at least
http://bugzilla.kernel.org/show_bug.cgi?id=13063
but probably a few other bugzilla entries too (12936, for example), and
is confirmed to fix Rafael's storage driver breakage after resume bug
report (no bugzilla entry).
We should also be able to now revert that ACPI battery fix.
Reported-and-tested-by: Rafael J. Wysocki <rjw@suse.com> Tested-by: Heinz Diehl <htd@fancy-poultry.org> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Duyck [Thu, 9 Apr 2009 22:49:39 +0000 (22:49 +0000)]
igb: do not check for vf_data if we didn't enable vfs
The driver is currently dumping a message in the log about failing to
allocate vf data when max_vfs is equal to 0. This change makes it so the
error message is only displayed if we set max_vfs to a non zero value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 9 Apr 2009 22:49:20 +0000 (22:49 +0000)]
igbvf: fix unused external references
The igbvbf driver exposed several unused extrnal references due to the fact
that code was copied from igb and then some functionality was removed.
This changes that so that unused functions are either removed or made
static.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 9 Apr 2009 22:49:02 +0000 (22:49 +0000)]
igb: fix unused external references introduced with sr-iov changes
There were several unused external references added with the sr-iov
enablement changes. This patch changes all those references to static
local references.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log