Replace the get_i2s_mclk callback with tables of MCLK values. This
simplifies the MCLK-handling code in both the framework and the model-
specific drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the DAC Oversampling mixer control because this setting does not
make much sense.
For cards with the H6 daughterboard, 128x oversampling was disabled
anyway because these high MCLK frequency would not be compatible with
the connector cable.
For cards without the H6 daughterboard, 128x gives a slightly higher
output quality; there is no reason to reduce it to 64x except for saving
power, but then these cards have not been designed to be power efficient
anyway (the D2's blinkenlights cannot be disabled).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 10 Jan 2011 15:07:11 +0000 (16:07 +0100)]
ALSA: virtuoso: configure correct master clock frequency on the CS2000
The clock output of the CS2000, which is used as master clock for the
DACs, was using half the actual master clock frequency for some reason.
Using the theoretically correct frequency seems also to work in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 10 Jan 2011 15:05:38 +0000 (16:05 +0100)]
ALSA: virtuoso: remove non-working controls on Essence ST Deluxe
On the Xonar Essence ST Deluxe, remove all mixer controls that would
require I2C communication with the third DAC, which does not work
because of an addressing conflict with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 10 Jan 2011 15:03:17 +0000 (16:03 +0100)]
ALSA: virtuoso: change PCM1796 format to I2S
Change the PCM format used for the PCM1796 from left-justified to I2S to
ensure that the correct format is used even for the Essence ST Deluxe's
center/LFE DAC, where I2C does not work because of an address conflict
with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 10 Jan 2011 15:02:32 +0000 (16:02 +0100)]
ALSA: virtuoso: wait for PCM1796 clock to become stable
The PCM1796 needs the master clock for I2C communication to work, so
add delays after clock changes to ensure that the clock is stable when
we try to write the DACs' registers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 10 Jan 2011 14:59:38 +0000 (15:59 +0100)]
ALSA: oxygen: allow different number of PCM and mixer channels
For cards like the Xonar HDAV1.3, differentiate between the number of
PCM channels that can be played and the number of channels whose volume
can be adjusted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jesper Juhl [Thu, 6 Jan 2011 21:19:47 +0000 (22:19 +0100)]
ALSA: Don't leak in sound/core/oss/pcm_oss.c::snd_pcm_hw_param_near()
snd_pcm_hw_param_near() will leak the memory allocated to 'save' if the
call to snd_pcm_hw_param_max() returns less than zero.
This patch makes sure we never leak.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv4/route.c: respect prefsrc for local routes
bridge: stp: ensure mac header is set
bridge: fix br_multicast_ipv6_rcv for paged skbs
atl1: fix oops when changing tx/rx ring params
drivers/atm/atmtcp.c: add missing atm_dev_put
starfire: Fix dma_addr_t size test for MIPS
tg3: fix return value check in tg3_read_vpd()
Broadcom CNIC core network driver: fix mem leak on allocation failures in cnic_alloc_uio_rings()
ISDN, Gigaset: Fix memory leak in do_disconnect_req()
CAN: Use inode instead of kernel address for /proc file
skfp: testing the wrong variable in skfp_driver_init()
ppp: allow disabling multilink protocol ID compression
ehea: Avoid changing vlan flags
ueagle-atm: fix PHY signal initialization race
Joel Sing [Mon, 3 Jan 2011 20:24:20 +0000 (20:24 +0000)]
ipv4/route.c: respect prefsrc for local routes
The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.
This bug can be demonstrated as follows:
# ifconfig dummy0 192.168.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 192.168.0.1
# ip route change table local local 192.168.0.1 dev dummy0 \
proto kernel scope host src 127.0.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 127.0.0.1
We now establish a local connection and verify the source IP
address selection:
Thus without the patch, with the boot parameters 'tcb selinux=0', adding
the above 'dont_measure obj_type=var_log_t' rule to the default IMA TCB
measurement policy, would result in nothing being measured. The patch
prevents the default TCB policy from being replaced.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com> Cc: James Morris <jmorris@namei.org> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: David Safford <safford@watson.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems fine itself, but br_send_bpdu() invokes ebtables LOCAL_OUT.
We oops in ebt_basic_match() because it assumes eth_hdr(skb) returns
a meaningful result.
Cc: acme@ghostprotocols.net
References: https://bugzilla.kernel.org/show_bug.cgi?id=24532 Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 3 Jan 2011 19:51:22 +0000 (11:51 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix callchain hit bad cast on ascii display
arch/x86/oprofile/op_model_amd.c: Perform initialisation on a single CPU
watchdog: Improve initialisation error message and documentation
Linus Torvalds [Mon, 3 Jan 2011 19:50:26 +0000 (11:50 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] em28xx: radio_fops should also use unlocked_ioctl
[media] wm8775: Revert changeset fcb9757333 to avoid a regression
[media] cx25840: Prevent device probe failure due to volume control ERANGE error
Linus Torvalds [Mon, 3 Jan 2011 19:48:54 +0000 (11:48 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: provide dummy functions for DMA_ENGINE=n
mv_xor: fix race in tasklet function
Tomas Winkler [Mon, 3 Jan 2011 19:26:08 +0000 (11:26 -0800)]
bridge: fix br_multicast_ipv6_rcv for paged skbs
use pskb_may_pull to access ipv6 header correctly for paged skbs
It was omitted in the bridge code leading to crash in blind
__skb_pull
since the skb is cloned undonditionally we also simplify the
the exit path
this fixes bug https://bugzilla.kernel.org/show_bug.cgi?id=25202
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 IEEE 802.11: authenticated
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 IEEE 802.11: associated (aid 2)
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 RADIUS: starting accounting session 4D0608A3-00000005
Dec 15 14:36:41 User-PC kernel: [175576.120287] ------------[ cut here ]------------
Dec 15 14:36:41 User-PC kernel: [175576.120452] kernel BUG at include/linux/skbuff.h:1178!
Dec 15 14:36:41 User-PC kernel: [175576.120609] invalid opcode: 0000 [#1] SMP
Dec 15 14:36:41 User-PC kernel: [175576.120749] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/uevent
Dec 15 14:36:41 User-PC kernel: [175576.121035] Modules linked in: approvals binfmt_misc bridge stp llc parport_pc ppdev arc4 iwlagn snd_hda_codec_realtek iwlcore i915 snd_hda_intel mac80211 joydev snd_hda_codec snd_hwdep snd_pcm snd_seq_midi drm_kms_helper snd_rawmidi drm snd_seq_midi_event snd_seq snd_timer snd_seq_device cfg80211 eeepc_wmi usbhid psmouse intel_agp i2c_algo_bit intel_gtt uvcvideo agpgart videodev sparse_keymap snd shpchp v4l1_compat lp hid video serio_raw soundcore output snd_page_alloc ahci libahci atl1c
Dec 15 14:36:41 User-PC kernel: [175576.122712]
Dec 15 14:36:41 User-PC kernel: [175576.122769] Pid: 0, comm: kworker/0:0 Tainted: G W 2.6.37-rc5-wl+ #3 1015PE/1016P
Dec 15 14:36:41 User-PC kernel: [175576.123012] EIP: 0060:[<f83edd65>] EFLAGS: 00010283 CPU: 1
Dec 15 14:36:41 User-PC kernel: [175576.123193] EIP is at br_multicast_rcv+0xc95/0xe1c [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.123362] EAX: 0000001c EBX: f5626318 ECX: 00000000 EDX: 00000000
Dec 15 14:36:41 User-PC kernel: [175576.123550] ESI: ec512262 EDI: f5626180 EBP: f60b5ca0 ESP: f60b5bd8
Dec 15 14:36:41 User-PC kernel: [175576.123737] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Dec 15 14:36:41 User-PC kernel: [175576.123902] Process kworker/0:0 (pid: 0, ti=f60b4000 task=f60a8000 task.ti=f60b0000)
Dec 15 14:36:41 User-PC kernel: [175576.124137] Stack:
Dec 15 14:36:41 User-PC kernel: [175576.124181] ec556500f6d06800f60b5be8c01087d8ec5122620000003000000024f5626180
Dec 15 14:36:41 User-PC kernel: [175576.124181] f572c200ef463440f56263003afffffff6d06dd0e60766a4000000c4f6d06860
Dec 15 14:36:41 User-PC kernel: [175576.124181] ffffffffec55652c00000001f6d06844f60b5c64c0138264c016e451c013e47d
Dec 15 14:36:41 User-PC kernel: [175576.124181] Call Trace:
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01087d8>] ? sched_clock+0x8/0x10
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0138264>] ? enqueue_entity+0x174/0x440
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c016e451>] ? sched_clock_cpu+0x131/0x190
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c013e47d>] ? select_task_rq_fair+0x2ad/0x730
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0524fc1>] ? nf_iterate+0x71/0x90
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4914>] ? br_handle_frame_finish+0x184/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4790>] ? br_handle_frame_finish+0x0/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e46e9>] ? br_handle_frame+0x189/0x230 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4790>] ? br_handle_frame_finish+0x0/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f83e4560>] ? br_handle_frame+0x0/0x230 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04ff026>] ? __netif_receive_skb+0x1b6/0x5b0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04f7a30>] ? skb_copy_bits+0x110/0x210
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0503a7f>] ? netif_receive_skb+0x6f/0x80
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82cb74c>] ? ieee80211_deliver_skb+0x8c/0x1a0 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82cc836>] ? ieee80211_rx_handlers+0xeb6/0x1aa0 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04ff1f0>] ? __netif_receive_skb+0x380/0x5b0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c016e242>] ? sched_clock_local+0xb2/0x190
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c012b688>] ? default_spin_lock_flags+0x8/0x10
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d83df>] ? _raw_spin_lock_irqsave+0x2f/0x50
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82cd621>] ? ieee80211_prepare_and_rx_handle+0x201/0xa90 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f82ce154>] ? ieee80211_rx+0x2a4/0x830 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f815a8d6>] ? iwl_update_stats+0xa6/0x2a0 [iwlcore]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f8499212>] ? iwlagn_rx_reply_rx+0x292/0x3b0 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d83df>] ? _raw_spin_lock_irqsave+0x2f/0x50
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f8483697>] ? iwl_rx_handle+0xe7/0x350 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<f8486ab7>] ? iwl_irq_tasklet+0xf7/0x5c0 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01aece1>] ? __rcu_process_callbacks+0x201/0x2d0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0150d05>] ? tasklet_action+0xc5/0x100
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0150a07>] ? __do_softirq+0x97/0x1d0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d910c>] ? nmi_stack_correct+0x2f/0x34
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0150970>] ? __do_softirq+0x0/0x1d0
Dec 15 14:36:41 User-PC kernel: [175576.124181] <IRQ>
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01508f5>] ? irq_exit+0x65/0x70
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05df062>] ? do_IRQ+0x52/0xc0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c01036b0>] ? common_interrupt+0x30/0x38
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c03a1fc2>] ? intel_idle+0xc2/0x160
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c04daebb>] ? cpuidle_idle_call+0x6b/0x100
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c0101dea>] ? cpu_idle+0x8a/0xf0
Dec 15 14:36:41 User-PC kernel: [175576.124181] [<c05d2702>] ? start_secondary+0x1e8/0x1ee
Cc: David Miller <davem@davemloft.net> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
J. K. Cliburn [Sat, 1 Jan 2011 05:02:12 +0000 (05:02 +0000)]
atl1: fix oops when changing tx/rx ring params
Commit 3f5a2a713aad28480d86b0add00c68484b54febc zeroes out the statistics
message block (SMB) and coalescing message block (CMB) when adapter ring
resources are freed. This is desirable behavior, but, as a side effect,
the commit leads to an oops when atl1_set_ringparam() attempts to alter
the number of rx or tx elements in the ring buffer (by using ethtool
-G, for example). We don't want SMB or CMB to change during this
operation.
Modify atl1_set_ringparam() to preserve SMB and CMB when changing ring
parameters.
Cc: stable@kernel.org Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Reported-by: Tõnu Raitviir <jussuf@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was that a temporary page table mapping was being improperly
restored.
The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort. The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0. This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Mike Rapoport [Wed, 29 Dec 2010 07:06:26 +0000 (09:06 +0200)]
ARM: it8152: add IT8152_LAST_IRQ definition to fix build error
The commit 6ac6b817f3f4c23c5febd960d8deb343e13af5f3 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:
CC arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1
Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ipchain__fprintf_graph() casts the number of hits in a branch as an
int, which means we lose its highests bits.
This results in meaningless number of callchain hits in perf.data
that have a high number of hits recorded, typically those that have
callchain branches hits appearing more than INT_MAX. This happens
easily as those are pondered by the event period.
Reported-by: Nick Piggin <npiggin@kernel.dk> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Paul Mackerras <paulus@samba.org>
Robert Richter [Mon, 3 Jan 2011 11:15:14 +0000 (12:15 +0100)]
arch/x86/oprofile/op_model_amd.c: Perform initialisation on a single CPU
Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.
[ 7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[ 7.034385] caller is setup_APIC_eilvt+0x155/0x180
[ 7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[ 7.034392] Call Trace:
[ 7.034400] [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[ 7.034404] [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]
Hans Verkuil [Sat, 18 Dec 2010 12:59:51 +0000 (09:59 -0300)]
[media] em28xx: radio_fops should also use unlocked_ioctl
em28xx uses core assisted locking, so it shouldn't use .ioctl.
The .ioctl callback was replaced by .unlocked_ioctl for video nodes,
but not for radio nodes. This is now corrected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] wm8775: Revert changeset fcb9757333 to avoid a regression
It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: Andy Walls <awalls@md.metrocast.net> Reported-by: Eric Sharkey <eric@lisaneric.org> Reported-by: Auric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 5 Dec 2010 22:42:30 +0000 (19:42 -0300)]
[media] cx25840: Prevent device probe failure due to volume control ERANGE error
This patch fixes a regression that crept into 2.6.36.
The volume control scale in the cx25840 driver has an unusual mapping
from register values to v4l2 volume control values. Enforce the mapping
limits, so that the default volume control setting does not fall out of
bounds to prevent the cx25840 module device probe from failing.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Axel Lin [Mon, 3 Jan 2011 01:26:53 +0000 (02:26 +0100)]
ARM: 6605/1: Add missing include "asm/memory.h"
This patch fixes below build error by adding the missing asm/memory.h,
which is needed for arch_is_coherent().
$ make pxa3xx_defconfig; make
CC init/do_mounts_rd.o
In file included from include/linux/list_bl.h:5,
from include/linux/rculist_bl.h:7,
from include/linux/dcache.h:7,
from include/linux/fs.h:381,
from init/do_mounts_rd.c:3:
include/linux/bit_spinlock.h: In function 'bit_spin_unlock':
include/linux/bit_spinlock.h:61: error: implicit declaration of function 'arch_is_coherent'
make[1]: *** [init/do_mounts_rd.o] Error 1
make: *** [init] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Hutchings [Sun, 2 Jan 2011 23:02:42 +0000 (23:02 +0000)]
watchdog: Improve initialisation error message and documentation
The error message 'NMI watchdog failed to create perf event...'
does not make it clear that this is a fatal error for the
watchdog. It also currently prints the error value as a
pointer, rather than extracting the error code with PTR_ERR().
Fix that.
Add a note to the description of the 'nowatchdog' kernel
parameter to associate it with this message.
Reported-by: Cesare Leonardi <celeonar@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: 599368@bugs.debian.org Cc: 608138@bugs.debian.org Cc: Don Zickus <dzickus@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: <stable@kernel.org> # .37.x and later
LKML-Reference: <1294009362.3167.126.camel@localhost> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Sun, 2 Jan 2011 18:37:19 +0000 (10:37 -0800)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kconfig: fix undesirable side effect of adding "visible" menu attribute
Andreas Mohr [Mon, 27 Dec 2010 20:17:26 +0000 (21:17 +0100)]
ALSA: azt3328: use proper private_data hookup for codec identification
- much improved implementation due to clean codec hierarchy
- preparation for potential per-codec spinlock change
NOTE: additionally removes a chip->pcm[codec_type] NULL ptr check
(due to it requiring access to external chip struct),
however I believe this to be ok since this condition should not occur
and most drivers don't check against that either.
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Avi Kivity [Fri, 31 Dec 2010 08:52:15 +0000 (10:52 +0200)]
KVM: i8259: initialize isr_ack
isr_ack is never initialized. So, until the first PIC reset, interrupts
may fail to be injected. This can cause Windows XP to fail to boot, as
reported in the fallout from the fix to
https://bugzilla.kernel.org/show_bug.cgi?id=21962.
Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Ben Hutchings [Wed, 29 Dec 2010 04:26:17 +0000 (04:26 +0000)]
starfire: Fix dma_addr_t size test for MIPS
Commit 56543af "starfire: use BUILD_BUG_ON for netdrv_addr_t" revealed
that the preprocessor condition used to find the size of dma_addr_t
yielded the wrong result for some architectures and configurations.
This was kluged for 64-bit PowerPC in commit 3e502e6 by adding yet
another case to the condition. However, 64-bit MIPS configurations
are not detected reliably either.
This should be fixed by using CONFIG_ARCH_DMA_ADDR_T_64BIT, but that
isn't yet defined everywhere it should be.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David Sterba [Wed, 29 Dec 2010 03:40:31 +0000 (03:40 +0000)]
tg3: fix return value check in tg3_read_vpd()
Besides -ETIMEDOUT and -EINTR, pci_read_vpd may return other error
values like -ENODEV or -EINVAL which are ignored due to the buggy
check, but the data are not read from VPD anyway and this is checked
subsequently with at most 3 needless loop iterations. This does not
show up as a runtime bug.
CC: Matt Carlson <mcarlson@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Juhl [Fri, 31 Dec 2010 19:18:48 +0000 (11:18 -0800)]
Broadcom CNIC core network driver: fix mem leak on allocation failures in cnic_alloc_uio_rings()
We are leaking memory in drivers/net/cnic.c::cnic_alloc_uio_rings() if
either of the calls to dma_alloc_coherent() fail. This patch fixes it by
freeing both the memory allocated with kzalloc() and memory allocated with
previous calls to dma_alloc_coherent() when there's a failure.
Thanks to Joe Perches <joe@perches.com> for suggesting a better
implementation than my initial version.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Rosenberg [Sun, 26 Dec 2010 06:54:53 +0000 (06:54 +0000)]
CAN: Use inode instead of kernel address for /proc file
Since the socket address is just being used as a unique identifier, its
inode number is an alternative that does not leak potentially sensitive
information.
CC-ing stable because MITRE has assigned CVE-2010-4565 to the issue.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 30 Dec 2010 20:09:26 +0000 (12:09 -0800)]
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/dvo: Report LVDS attached to ch701x as connected
Revert "drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks"
drm/i915: Verify Ironlake eDP presence on DP_A using the capability fuse
drm/i915, intel_ips: When i915 loads after IPS, make IPS relink to i915.
drm/i915/sdvo: Add hdmi connector properties after initing the connector
drm/i915: Set the required VFMUNIT clock gating disable on Ironlake.
Do not check for init flag before starting I/O - zram module is unusable
without this fix.
The oops mentioned in the reverted commit message was actually a problem
only with the zram version as present in project's own repository where
we allocate struct zram_stats_cpu upon device initialization. OTOH, In
mainline/staging version of zram, we allocate struct stats upfront, so
this oops cannot happen in mainline version.
Checking for init_done flag in zram_make_request() results in a *no-op*
for any I/O operation since we simply always return success. This flag
is actually set when the first write occurs on a zram disk which
triggers its initialization.
Linus Torvalds [Thu, 30 Dec 2010 18:07:44 +0000 (10:07 -0800)]
Merge branch 'merge-spi' of git://git.secretlab.ca/git/linux-2.6
* 'merge-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/m68knommu: Coldfire QSPI platform support
spi/omap2_mcspi.c: Force CS to be in inactive state after off-mode transition
memcg: fix wrong VM_BUG_ON() in try_charge()'s mm->owner check
At __mem_cgroup_try_charge(), VM_BUG_ON(!mm->owner) is checked.
But as commented in mem_cgroup_from_task(), mm->owner can be NULL
in some racy case. This check of VM_BUG_ON() is bad.
A possible story to hit this is at swapoff()->try_to_unuse(). It passes
mm_struct to mem_cgroup_try_charge_swapin() while mm->owner is NULL. If we
can't get proper mem_cgroup from swap_cgroup information, mm->owner is used
as charge target and we see NULL.
Chris Wilson [Thu, 30 Dec 2010 09:07:15 +0000 (09:07 +0000)]
Revert "drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks"
As I feared, whilst this fixed the clocks for the Lenovo U160, it broke
many other machines. So lets reverts commit 448f53a1ede54eb854d036abf
and search for the real bug.
Reported-and-tested-by: Travis Hume <travis@computoring.org> [et al]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=25842
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32698 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Daniel T Chen [Tue, 28 Dec 2010 22:20:02 +0000 (17:20 -0500)]
ALSA: hda: Use LPIB quirk for Dell Inspiron m101z/1120
Sjoerd Simons reports that, without using position_fix=1, recording
experiences overruns. Work around that by applying the LPIB quirk
for his hardware.
Reported-and-tested-by: Sjoerd Simons <sjoerd@debian.org> Cc: <stable@kernel.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Rosenberg [Sat, 25 Dec 2010 21:23:40 +0000 (16:23 -0500)]
sound: Prevent buffer overflow in OSS load_mixer_volumes
The load_mixer_volumes() function, which can be triggered by
unprivileged users via the SOUND_MIXER_SETLEVELS ioctl, is vulnerable to
a buffer overflow. Because the provided "name" argument isn't
guaranteed to be NULL terminated at the expected 32 bytes, it's possible
to overflow past the end of the last element in the mixer_vols array.
Further exploitation can result in an arbitrary kernel write (via
subsequent calls to load_mixer_volumes()) leading to privilege
escalation, or arbitrary kernel reads via get_mixer_levels(). In
addition, the strcmp() may leak bytes beyond the mixer_vols array.
After grabbing a msg from the msgq, the mcfqspi_work function calls
list_del_init on the mcfqspi->msgq which unintentionally deletes the rest
of the list before it can be processed. If qspi call was made using
spi_sync, this can result in a process hang.
Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com> Acked-by: Steven King <sfking@fdwdc.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jan Beulich [Thu, 9 Dec 2010 08:11:38 +0000 (08:11 +0000)]
kconfig: fix undesirable side effect of adding "visible" menu attribute
This lead to non-selected, non-user-selectable options to be written
out to .config. This is not only pointless, but also preventing the
user to be prompted should any of those options eventually become
visible (e.g. by de-selecting the *_AUTO options the "visible"
attribute was added for.
Furthermore it is quite logical for the "visible" attribute of a menu
to control the visibility of all contained prompts, which is what the
patch does.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Michal Marek <mmarek@suse.cz>
Gregory CLEMENT [Wed, 29 Dec 2010 10:52:53 +0000 (11:52 +0100)]
spi/omap2_mcspi.c: Force CS to be in inactive state after off-mode transition
When SPI wake up from OFF mode, CS is in the wrong state: force it to the
inactive state.
During the system life, I monitored the CS behavior using a oscilloscope.
I also activated debug in omap2_mcspi, so I saw when driver disable the clocks
and restore context when device is not used.Each time the CS was in the correct
state. It was only when system was put suspend to ram with off-mode activated
that on resume the CS was in wrong state( ie activated).
Changelog:
* Change from v1 to v2:
- Rebase on linus/master (after 2.6.37-rc1)
- Do some clean-up and fix indentation on both patches
- Add more explanations for patch 2
* Change from v2 to v3:
- Use directly resume function of spi_master instead of using function
- from spi_device as Grant Likely pointed it out.
- Force this transition explicitly for each CS used by a device.
* Change from v3 to v4:
- Patch clean-up according to Kevin Hilman and checkpatch.
- Now force CS to be in inactive state only if it was inactive when it was
suspended.
* Change from v4 to v5:
- Rebase on linus/master (after 2.6.37-rc3)
- Collapse some lines as pointed by Grant Likely
- Fix a spelling
* Change from v5 to v6:
- Rebase on linus/master (after 2.6.37-rc7)
- Use CONFIG_SUSPEND instead of CONFIG_PM
- Didn't use legacy PM methods anymore. Instead, add a struct dev_pm_ops and
add the resume method there.
- Fix multi-line comment style
* Change from v6 to v7:
- Rebase on linus/master (after 2.6.37-rc8)
- Drop an extra line
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Avi Kivity [Tue, 28 Dec 2010 10:09:07 +0000 (12:09 +0200)]
KVM: MMU: Fix incorrect direct gfn for unpaged mode shadow
We use the physical address instead of the base gfn for the four
PAE page directories we use in unpaged mode. When the guest accesses
an address above 1GB that is backed by a large host page, a BUG_ON()
in kvm_mmu_set_gfn() triggers.
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=21962 Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com>
KVM-Stable-Tag. Signed-off-by: Avi Kivity <avi@redhat.com>
Linus Torvalds [Tue, 28 Dec 2010 23:54:24 +0000 (15:54 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring_buffer: Off-by-one and duplicate events in ring_buffer_read_page
Linus Torvalds [Tue, 28 Dec 2010 23:53:54 +0000 (15:53 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/microcode: Fix double vfree() and remove redundant pointer checks before vfree()
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8753 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Furthermore the generic cache uses zero-based numbering while the wm8753 cache
uses one-based numbering.
Thus we end up with two from each other incoherent caches, which leads to undefined
behaviour and crashes.
This patch fixes the issue by changing the wm8753 driver to use the generic
register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
projects / mv-sheeva.git / log