The transfer of ->flags causes some of the static mapping virtual
addresses to be prematurely freed (before the mapping is removed) because
VM_LAZY_FREE gets "set" if tmp->flags has VM_IOREMAP set. This might
cause subsequent vmalloc/ioremap calls to fail because it might allocate
one of the freed virtual address ranges that aren't unmapped.
va->flags has different types of flags from tmp->flags. If a region with
VM_IOREMAP set is registered with vm_area_add_early(), it will be removed
by __purge_vmap_area_lazy().
Fix vmalloc_init() to correctly initialize vmap_area for the given
vm_struct.
Also initialise va->vm. If it is not set, find_vm_area() for the early
vm regions will always fail.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com> Cc: "Olav Haugan" <ohaugan@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 645747462435 ("vmscan: detect mapped file pages used only once")
made mapped pages have another round in inactive list because they might
be just short lived and so we could consider them again next time. This
heuristic helps to reduce pressure on the active list with a streaming
IO worklods.
This patch fixes a regression introduced by this commit for heavy shmem
based workloads because unlike Anon pages, which are excluded from this
heuristic because they are usually long lived, shmem pages are handled
as a regular page cache.
This doesn't work quite well, unfortunately, if the workload is mostly
backed by shmem (in memory database sitting on 80% of memory) with a
streaming IO in the background (backup - up to 20% of memory). Anon
inactive list is full of (dirty) shmem pages when watermarks are hit.
Shmem pages are kept in the inactive list (they are referenced) in the
first round and it is hard to reclaim anything else so we reach lower
scanning priorities very quickly which leads to an excessive swap out.
Let's fix this by excluding all swap backed pages (they tend to be long
lived wrt. the regular page cache anyway) from used-once heuristic and
rather activate them if they are referenced.
The customer's workload is shmem backed database (80% of RAM) and they
are measuring transactions/s with an IO in the background (20%).
Transactions touch more or less random rows in the table. The
transaction rate fell by a factor of 3 (in the worst case) because of
commit 64574746. This patch restores the previous numbers.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vma length in dup_mmap is calculated and stored in a unsigned int,
which is insufficient and hence overflows for very large maps (beyond
16TB). The following program demonstrates this:
block congestion control doesn't have any concept of fairness across
multiple queues. This means that if SCSI reports the host as busy in
the queue congestion control it can result in an unfair starvation
situation in dm-mp if there are multiple multipath devices on the same
host. For example:
http://www.redhat.com/archives/dm-devel/2012-May/msg00123.html
The fix for this is to report only the sdev busy state (and ignore the
host busy state) in the block congestion control call back.
The host is still congested, but the SCSI subsystem will sort out the
congestion in a fair way because it knows the relation between the
queues and the host.
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Broke the scsi_wait_scan module in 2.6.30. Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.
The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.
Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The microblaze architecture does not provide a native GPIO API implementation
nor requires GPIOLIB, but still selects GENERIC_GPIO by default. As a result the
following build error occurs, if GPIOLIB is not selected:
include/asm-generic/gpio.h: In function 'gpio_get_value_cansleep':
include/asm-generic/gpio.h:218: error: implicit declaration of function '__gpio_get_value'
include/asm-generic/gpio.h: In function 'gpio_set_value_cansleep':
include/asm-generic/gpio.h:224: error: implicit declaration of function '__gpio_set_value'
This patch addresses the issue by not selecting GENERIC_GPIO by default. This
causes the GPIO API to be stubbed out if no implementation is provided.
If at exofs_fill_super() we had an early termination
do to any error, like an IO error while reading the
super-block. We would crash inside exofs_free_sbi().
This is because sbi->oc.numdevs was set to 1, before
we actually have a device table at all.
Fix it by moving the sbi->oc.numdevs = 1 to after the
allocation of the device table.
The notification of the transfer complete by calling complete()
should be done after clearing all interrupt status.
This avoids the race condition of misconfigure the i2c controller
in multi-core environment.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running on 32bit the mce handler could misinterpret
vm86 mode as ring 0. This can affect whether it does recovery
or not; it was possible to panic when recovery was actually
possible.
Fix this by always forcing vm86 to look like ring 3.
Cardhu's eMMC controller is on sdhci@78000600, not sdhci@78000400.
Fix the typo. This roughly doubles the IO performance, since the
support-8bit property actually takes effect.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't be holding the mmap_sem while calling flush_cache_user_range
because the flush can fault. If we fault on a user address, the
page fault handler will try to take mmap_sem again. Since both places
acquire the read lock, most of the time it succeeds. However, if another
thread tries to acquire the write lock on the mmap_sem (e.g. mmap) in
between the call to flush_cache_user_range and the fault, the down_read
in do_page_fault will deadlock.
[will: removed drop of vma parameter as already queued by rmk (7365/1)]
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Dima Zavin <dima@android.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vma isn't used and flush_cache_user_range isn't a standard macro that
is used on several archs with the same prototype. In fact only unicore32
has a macro with the same name (with an identical implementation and no
in-tree users).
This is a part of a patch proposed by Dima Zavin (with Message-id: 1272439931-12795-1-git-send-email-dima@android.com) that didn't get
accepted.
Cc: Dima Zavin <dima@android.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device info into list before doing context mapping, because device
info will be used by iommu_enable_dev_iotlb(). Without it, ATS won't get
enabled as it should be.
ATS, while a dubious decision from a security point of view, can be very
important for performance.
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flag of IRQF_ONESHOT should be passed to request_threaded_irq,
otherwise the following failure message should be dumped because
hardware handler is defined as NULL:
[ 3.383483] genirq: Threaded irq requested with handler=NULL and
!ONESHOT for irq 368
[ 3.392730] omap_hsmmc: probe of omap_hsmmc.0 failed with error -22
The patch fixes one kernel hang bug which is caused by mmc card
probe failure and root device can't be brought up.
Signed-off-by: Ming Lei <ming.lei@canonical.com> Acked-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 06e8935feb ("optimized SDIO IRQ handling for single irq")
introduced some spurious calls to SDIO function interrupt handlers,
such as when the SDIO IRQ thread is started, or the safety check
performed upon a system resume. Let's add a flag to perform the
optimization only when a real interrupt is signaled by the host
driver and we know there is no point confirming it.
Reported-by: Sujit Reddy Thumma <sthumma@codeaurora.org> Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus pointed out that there was no value is checking whether m->ip
was zero - because zero is a legimate value. If we have a reliable
(or faked in the VM86 case) "m->cs" we can use it to tell whether we
were in user mode or kernelwhen the machine check hit.
The symbol jiffies is created in the linker script as an alias to
jiffies_64. Unfortunately this is done outside any section, and
apparently GNU ld 2.21 doesn't carry the section with it, so we end up
with an absolute symbol and therefore a broken kernel.
Add jiffies and jiffies_64 to the whitelist.
The most disturbing bit with this discovery is that it shows that we
have had multiple linker bugs in this area crossing multiple
generations, and have been silently building bad kernels for some time.
a3e854d95 x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
ld version 2.22.52.0.[12] can incorrectly promote relative symbols to
absolute, if the output section they appear in is otherwise empty.
Since checkin:
6520fe55 x86, realmode: 16-bit real-mode code support for relocs tool
we actually check for this and error out rather than silently creating
a kernel which will malfunction if relocated.
Ingo found a configuration in which __start_builtin_fw triggered the
warning.
Go through the linker script sources and look for more symbols that
could plausibly get bogusly promoted to absolute, and add them to the
whitelist.
In general, if the following error triggers:
Invalid absolute R_386_32 relocation: <symbol>
... then we should verify that <symbol> is really meant to be
relocated, and add it and any related symbols manually to the S_REL
regexp.
Please note that 6520fe55 does not introduce the error, only the check
for the error -- without 6520fe55 this version of ld will simply
produce a corrupt kernel if CONFIG_RELOCATABLE is set on x86-32.
Reported-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PV on HVM guests map GSIs into event channels. At restore time the
event channels are resumed by restore_pirqs.
Device drivers might try to register the same GSI again through ACPI at
restore time, but the GSI has already been mapped and bound by
restore_pirqs. This patch detects these situations and avoids
mapping the same GSI multiple times.
Without this patch we get:
(XEN) irq.c:2235: dom4: pirq 23 or emuirq 28 already mapped
and waste a pirq.
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed spi device initialization of dev.parent pointer
to be the master's device pointer instead of his parent.
This introduced a bug in spi-fsl-spi, since its usage of spi device
pointer was not updated accordingly. This was later fixed by commit 5039a86, "spi/mpc83xx: fix NULL pdata dereference bug", but it missed
another spot on fsl_spi_cs_control function where we also need to update
usage of spi device pointer. This change address that.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfadd838(powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO
driver) added an unconditional call of chip->irq_eoi() to the demux
handler.
This leads to a NULL pointer derefernce on MPC512x platforms which use
this driver as well.
Make it conditional.
Reported-by: Thomas Wucher <thwucher@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Felix Radensky <felix@embedded-sol.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This originally started as a patch from Bernard as a way of simply
setting the VS scheduler. After submitting the RFC patch, we decided to
also modify the DS scheduler. To be most explicit, I've made the patch
explicitly set all scheduler modes, and included the defines for other
modes (in case someone feels frisky later).
The rest of the story gets a bit weird. The first version of the patch
showed an almost unbelievable performance improvement. Since rebasing my
branch it appears the performance improvement has gone, unfortunately.
But setting these bits seem to be the right thing to do given that the
docs describe corruption that can occur with the default settings.
In summary, I am seeing no more perf improvements (or regressions) in my
limited testing, but we believe this should be set to prevent rendering
corruption, therefore cc stable.
v1: Clear bit 4 also (Ken + Eugeni)
Do a full clear + set of the bits we want (Me).
Cc: Bernard Kilarski <bernard.r.kilarski@intel.com>
Reviewed-by (RFC): Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a dummy read of a PCI MMIO register that occurs before the SSB bus
has been powered, which is an error. This bug has not been seen earlier,
but was apparently exposed when udev was updated to version 182.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB2 LPM is disabled when device begin to suspend and enabled after device
is resumed. That's because USB spec does not define the transition from
U1/U2 state to U3 state.
If usb_port_suspend() fails, usb_port_resume() is never called, and USB2 LPM
is disabled in this situation. Enable USB2 LPM if port suspend fails.
Some more data structures must be freed and counters
reset if an XHCI controller has lost power. The failure
to do so renders some chips inoperative after a certain number
of S4 cycles.
Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic". When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine. The device is:
Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.
The successful completion code and non-zero untransferred length is a
contradiction. The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred. Otherwise, the transfer
should be marked with a short packet completion code. Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length. With it, we know to trust
the untransferred length.
Add a new xHCI quirk for the Fresco Logic host controller. If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning. For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.
This should be backported to stable kernels that contain the commit f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some
Fresco Logic hosts." That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Sergio Correia <lists@uece.net> Tested-by: Sergio Correia <lists@uece.net> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero. Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.
This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.
The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().
This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.
This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load. The ports will be powered off and seem "dead" to the
user.
Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Eric Anholt <eric.anholt@intel.com> Reported-by: David Bein <d.bein@f5.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a bit-array to xhci bus_state for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when xhci_hub_status_data() is called, the routine will return
a non-zero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
This patch should be backported to kernels as old as 3.4, that contain
the commit 879d38e6bc36d73b0ac40ec9b0d839fda9fa8b1a "USB: fix race
between root-hub suspend and remote wakeup".
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dTD's next dtd pointer need to be updated once CPU writes it, or this
request may not be handled by controller, then host will get NAK from
device forever.
This problem occurs when there is a request is handling, we need to add
a new request to dTD list, if this new request is added before the current
one is finished, the new request is intended to added as next dtd pointer
at current dTD, but without wmb(), the dTD's next dtd pointer may not be
updated when the controller reads it. In that case, the controller will
still get Terminate Bit is 1 at dTD's next dtd pointer, that means there is
no next request, then this new request is missed by controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kontron M2M development board, also known as the Fish River Island II,
has an optional daughter card providing access to the PCH_UART (EG20T) via
a ti_usb_3410_5052 uart to usb chip.
A possible race condition appears because we are not initializing
the ohci->regs before calling usb_hcd_request_irqs().
We move the call to ohci_init() in hcd->driver->reset() instead of
hcd->driver->start() to fix this.
This was experienced when we share the same IRQ line between OHCI and EHCI
controllers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Christian Eggers <christian.eggers@kathrein.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c2344f13b59e007d782a3e591ebc551bc583a8b7 (USB: gpio_vbus:
add delayed vbus_session calls, 2009-01-24), usb_gadget_vbus_connect()
and ...disconnect() were extracted from the interrupt handler, so to
allow vbus_session handlers to deal with msleep() calls.
This patch takes the approach one step further.
USB2.0 specification (7.1.7.3 Connect and Disconnect Signaling) says
that the USB system software (shall) provide a debounce interval with
a minimum duration of 100 ms, which ensures that the electrical and
mechanical connection is stable before software attempts to reset
the attached device.
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0f) created a regression
with Beagleboard xM if booting the kernel after running 'usb start' under u-boot.
Finishing the reset before calling 'usb_add_hcd' fixes the regression. This is most likely due to
usb_add_hcd calling the driver's reset and init functions which expect the hardware to be
up and running.
The update_device callback is not needed and the function used here is
from the pci ehci driver. Without this patch we get a compile error if
ehci-platform is compiled without ehci-pci.
The out functions should only handle actual available data instead of the complete buffer.
Otherwise for example the ep0_consume function will report ghost events since it tries to decode
the complete buffer - which may contain partly invalid data.
This patch (as1550) fixes a bug in the usb-serial core that affects
the ftdi_sio driver and most likely others as well. The core
implements suspend and resume routines, but it doesn't store pointers
to those routines in the usb_driver structures that it registers,
even though it does set those drivers' supports_autosuspend flag. The
end result is that when one of these devices is autosuspended, we try
to call through a NULL pointer.
The patch fixes the problem by setting the suspend and resume method
pointers to the appropriate routines in the USB serial core, along
with the supports_autosuspend field, in each driver as it is
registered.
This should be back-ported to all the stable kernels that have the new
usb_serial_register_drivers() interface.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Frank Schäfer <schaefer.frank@gmx.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rules used to make 8250_pci "ignore" the PCH uarts are lacking pci subids
entries, preventing it to match and thus is breaking serial port support for
theses systems.
This has been tested on a nanoETXexpress-TT, which has a specifici uart clock.
Tested-by: Erwan Velu <Erwan.Velu@zodiacaerospace.com>
[stable@: please apply to 3.0-stable, 3.2-stable and 3.3-stable] Signed-off-by: Arnaud Patard <apatard@hupstream.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We noticed that we were loosing data at speed less than 2400 baud.
It turned out our (TI16750 compatible) uart with 64 byte outgoing fifo
was truncated to 16 byte (bit 5 sets fifo len) when modifying the fcr
reg.
The input code still fills the buffer with 64 bytes if I remember
correctly and thus data is lost.
Our fix was to remove whiping of the fcr content and just add the
TRIGGER_1 which we want for latency.
I can't see why this would not work on less than 2400 always, for all
uarts ...
Otherwise one would have to make sure the filling of the fifo re-checks
the current state of available fifo size (urrk).
Signed-off-by: Christian Melki <christian.melki@ericsson.se> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A flush request is usually issued in transaction commit code path, so
using GFP_KERNEL to allocate memory for flush request bio falls into
the classic deadlock issue.
This is suitable for any -stable kernel to which it applies as it
avoids a possible deadlock.
This implied a reference counting bug and the problem happened during
mbind().
mbind() applies a new memory policy to a range and uses mbind_range() to
merge existing VMAs or split them as necessary. In the event of splits,
mpol_dup() will allocate a new struct mempolicy and maintain existing
reference counts whose rules are documented in
Documentation/vm/numa_memory_policy.txt .
The problem occurs with shared memory policies. The vm_op->set_policy
increments the reference count if necessary and split_vma() and
vma_merge() have already handled the existing reference counts.
However, policy_vma() screws it up by replacing an existing
vma->vm_policy with one that potentially has the wrong reference count
leading to a premature free. This patch removes the damage caused by
policy_vma().
With this patch applied Dave's trinity tool runs an mbind test for 5
minutes without error. /proc/slabinfo reported that there are no
numa_policy or shared_policy_node objects allocated after the test
completed and the shared memory region was deleted.
Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: Dave Jones <davej@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Stephen Wilson <wilsons@start.ca> Cc: Christoph Lameter <cl@linux.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
worker_enter_idle() has WARN_ON_ONCE() which triggers if nr_running
isn't zero when every worker is idle. This can trigger spuriously
while a cpu is going down due to the way trustee sets %WORKER_ROGUE
and zaps nr_running.
It first sets %WORKER_ROGUE on all workers without updating
nr_running, releases gcwq->lock, schedules, regrabs gcwq->lock and
then zaps nr_running. If the last running worker enters idle
inbetween, it would see stale nr_running which hasn't been zapped yet
and trigger the WARN_ON_ONCE().
Fix it by performing the sanity check iff the trustee is idle.
Prevents dereferencing an invalid struct usb_interface
pointer.
Always delete entry from device list whether or not the
rest of the device state cleanup is postponed. The device
list uses desc->intf as key, and wdm_open will dereference
this key while searching for a matching device. A device
should not appear in the list unless probe() has succeeded
and disconnect() has not finished.
We cannot dereference a removed USB interface for
dev_printk. Use pr_debug instead where necessary.
Flush errors are expected if device is unplugged and are
therefore best ingored at this point.
Move the kill_urbs() call in wdm_release with dev_dbg()
for the non disconnect, as we know it has already been
called if WDM_DISCONNECTING is set. This does not
actually fix anything, but keeps the code more consistent.
cleanup() is not called if the last close() comes after
disconnect(). That leads to a memory leak. Rectified
by checking for an earlier disconnect() in release()
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a longstanding bug, almost unnoticeable when calling
persistent_ram_write() for small buffers.
But when called for large data buffers, the write routine behaves
incorrectly, as the size may never update: instead of clamping
the size to the maximum buffer size, buffer_size_add_clamp() returns
an error (which is never checked by the write routine, btw).
To fix this, we now use buffer_size_add() that actually clamps the
size to the max value.
Also remove buffer_size_add_clamp(), it is no longer needed.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org> Acked-by: Colin Cross <ccross@android.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UML uses the _PAGE_NEWPAGE flag to mark pages which are not jet
installed on the host side using mmap().
pte_same() has to ignore this flag, otherwise unuse_pte_range()
is unable to unuse the page because two identical
page tables entries with different _PAGE_NEWPAGE flags would not
match and swapoff() would never return.
The current __swp_type() function uses a too small bitshift.
Using more than one swap files causes bad pages because
the type bits clash with other page flags.
On big-endian systems (e.g., Apple PowerBook), trying to use a
logitech wireless mouse with the Logitech Unifying Receiver does not
work with v3.2 and later kernels. The device doesn't show up in
/dev/input. Older kernels work fine.
That is because the new hid-logitech-dj driver claims the device. The
device arrival notification appears:
20 00 41 02 00 00 00 00 00 00 00 00 00 00 00
and we read the report_types bitfield (02 00 00 00) to find out what
kind of device it is. Unfortunately the driver only reads the first 8
bits and treats that value as a 32-bit little-endian number, so on a
powerpc the report type seems to be 0x02000000 and is not recognized.
Even on little-endian machines, connecting a media center remote
control (report type 00 01 00 00) with this driver loaded would
presumably fail for the same reason.
Fix both problems by using get_unaligned_le32() to read all four
bytes, which is a little clearer anyway. After this change, the
wireless mouse works on Hugo's PowerBook again.
Based on a patch by Nestor Lopez Casado.
Addresses http://bugs.debian.org/671292
On some HCDs usb_unlink_urb() can directly call the
completion handler. That limits the spinlocks that can
be taken in the handler to locks not held while calling
usb_unlink_urb()
To prevent a race with resubmission, this patch exposes
usbcore's infrastructure for blocking submission, uses it
and so drops the lock without causing a race in usbhid.
We incorrectly parse incoming IR data. The extra byte contains the upper
bits and not the lower bits of the x/y coordinates. User-space expects
absolute position data from us so this patch does not break existing
applications. On the contrary, it extends the virtual view and fixes
garbage reports for margin areas of the virtual screen.
Reported-by: Peter Bukovsky <bukovsky.peter@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bc3e53f682d9 ("mm: distinguish between mlocked and pinned
pages") introduced a separate counter for pinned pages and used it in
the IB stack. However, in ib_umem_get() the pinned counter is
incremented, but ib_umem_release() wrongly decrements the locked
counter. Fix this.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Christoph Lameter <cl@linux.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We reset the bool names and values array to NULL, but do not reset the
number of entries in these arrays to 0. If we error out and then get back
into this function we will walk these NULL pointers based on the belief
that they are non-zero length.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the 32-bit compat keyctl() syscall wrapper on Sparc64 for Sparc32 binary
compatibility.
Without this, keyctl(KEYCTL_INSTANTIATE_IOV) is liable to malfunction as it
uses an iovec array read from userspace - though the kernel should survive this
as it checks pointers and sizes anyway.
I think all the other keyctl() function should just work, provided (a) the top
32-bits of each 64-bit argument register are cleared prior to invoking the
syscall routine, and the 32-bit address space is right at the 0-end of the
64-bit address space. Most of the arguments are 32-bit anyway, and so for
those clearing is not required.
Signed-off-by: David Howells <dhowells@redhat.com
cc: "David S. Miller" <davem@davemloft.net>
cc: sparclinux@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771dae818 (powerpc/cpuidle: Add cpu_idle_wait() to allow
switching of idle routines) implemented cpu_idle_wait() for powerpc.
The changelog says:
"The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.":
Unfortunately the changelog is completely useless as it does not tell
_WHY_ it is different.
Aside of being different the implementation is patently wrong.
The rescheduling IPI is async. That means that there is no guarantee,
that the other cores have executed the IPI when cpu_idle_wait()
returns. But that's the whole purpose of this function: to guarantee
that no CPU uses the old idle handler anymore.
Use the smp_functional_call() based implementation, which fulfils the
requirements.
[ This code is going to replaced by a core version to remove all the
pointless copies in arch/*, but this one should go to stable ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Cc: Trinabh Gupta <g.trinabh@gmail.com> Cc: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Link: http://lkml.kernel.org/r/20120507175651.980164748@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function import_ep() is incorrectly using ep->dst instead of the dst
ptr passed in. This causes a crash when accepting new rdma connections
becase ep->dst is not initialized yet.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
Reported-by: Dave Jiang <dave.jiang@intel.com> Tested-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioc->pfacts member in the IOC structure is getting set to zero
following a call to _base_get_ioc_facts due to the memset in that routine.
So if the ioc->pfacts was read after a host reset, there would be a NULL
pointer dereference. The routine _base_get_ioc_facts is called from context
of host reset. The problem in _base_get_ioc_facts is the size of
Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60,
so there is a four byte overflow resulting from the memset.
Also, there is memset in _base_get_port_facts using the incorrect structure,
it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply.
When setting the current task state to TASK_UNINTERRUPTIBLE this can
race with a different cpu. The other cpu could set the task state after
it inspected it (while it was still TASK_RUNNING) to TASK_RUNNING which
would change the state from TASK_UNINTERRUPTIBLE to TASK_RUNNING again.
This race was always present in the pfault interrupt code but didn't
cause anything harmful before commit f2db2e6c "[S390] pfault: cpu hotplug
vs missing completion interrupts" which relied on the fact that after
setting the task state to TASK_UNINTERRUPTIBLE the task would really
sleep.
Since this is not necessarily the case the result may be a list corruption
of the pfault_list or, as observed, a use-after-free bug while trying to
access the task_struct of a task which terminated itself already.
To fix this, we need to get a reference of the affected task when receiving
the initial pfault interrupt and add special handling if we receive yet
another initial pfault interrupt when the task is already enqueued in the
pfault list.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During early boot, when the scheduler hasn't really been fully set up,
we really can't do blocking allocations because with certain (dubious)
configurations the "might_resched()" calls can actually result in
scheduling events.
We could just make such users always use GFP_ATOMIC, but quite often the
code that does the allocation isn't really aware of the fact that the
scheduler isn't up yet, and forcing that kind of random knowledge on the
initialization code is just annoying and not good for anybody.
And we actually have a the 'gfp_allowed_mask' exactly for this reason:
it's just that the kernel init sequence happens to set it to allow
blocking allocations much too early.
So move the 'gfp_allowed_mask' initialization from 'start_kernel()'
(which is some of the earliest init code, and runs with preemption
disabled for good reasons) into 'kernel_init()'. kernel_init() is run
in the newly created thread that will become the 'init' process, as
opposed to the early startup code that runs within the context of what
will be the first idle thread.
So by the time we reach 'kernel_init()', we know that the scheduler must
be at least limping along, because we've already scheduled from the idle
thread into the init thread.
Reported-by: Steven Rostedt <rostedt@goodmis.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has happened twice now where elaborate troubleshooting has
undergone on systems where CONFIG_CFG80211_INTERNAL_REGDB [0]
has been set but yet net/wireless/db.txt was not updated.
Despite the documentation on this it seems system integrators could
use some more help with this, so throw out a kernel warning at boot time
when their database is empty.
This does mean that the error-prone system integrator won't likely
realize the issue until they boot the machine but -- it does not seem
to make sense to enable a build bug breaking random build testing.
We had for some reason overlooked the AIO interface, and it didn't use
the proper rw_verify_area() helper function that checks (for example)
mandatory locking on the file, and that the size of the access doesn't
cause us to overflow the provided offset limits etc.
Instead, AIO did just the security_file_permission() thing (that
rw_verify_area() also does) directly.
This fixes it to do all the proper helper functions, which not only
means that now mandatory file locking works with AIO too, we can
actually remove lines of code.
An out-of-place "OK" response to the "AT+GMR" (get firmware version)
command turns out to be, more often than not, a delayed response to
a previous command rather than an actual error, so continue waiting
for the version number in that case.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DISCONNECT_B3_IND was synthesized because of a DISCONNECT_REQ
with existing logical connections, the connection state wasn't
updated accordingly. Also the emitted DISCONNECT_B3_IND message
wasn't included in the debug log as requested.
This patch fixes both of these issues.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a global ratelimit for CAPI message dumps to protect
against possible log flood.
Drop the ratelimit for ignored messages which is now covered by the
global one.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 19 May 2012 22:30:15 +0000 (15:30 -0700)]
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PA-RISC fixes from James Bottomley:
"This is a set of three bug fixes that gets parisc running again on
systems with PA1.1 processors.
Two fix regressions introduced in 2.6.39 and one fixes a prefetch bug
that only affects PA7300LC processors. We also have another pending
fix to do with the sectional arrangement of vmlinux.lds, but there's a
query on it during testing on one particular system type, so I'll hold
off sending it in for now."
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix panic on prefetch(NULL) on PA7300LC
[PARISC] fix crash in flush_icache_page_asm on PA1.1
[PARISC] fix PA1.1 oops on boot
Linus Torvalds [Sat, 19 May 2012 22:28:22 +0000 (15:28 -0700)]
Merge branch 'x86/ld-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 linker bug workarounds from Peter Anvin.
GNU ld-2.22.52.0.[12] (*) has an unfortunate bug where it incorrectly
turns certain relocation entries absolute. Section-relative symbols
that are part of otherwise empty sections are silently changed them to
absolute. We rely on section-relative symbols staying section-relative,
and actually have several sections in the linker script solely for this
purpose.
We could just black-list the buggy linker, but it appears that it got
shipped in at least F17, and possibly other distros too, so it's sadly
not some rare unusual case.
This backports the workaround from the x86/trampoline branch, and as
Peter says: "This is not a minimal fix, not at all, but it is a tested
code base."
* 'x86/ld-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, relocs: When printing an error, say relative or absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
x86, realmode: 16-bit real-mode code support for relocs tool
(*) That's a manly release numbering system. Stupid, sure. But manly.
projects / karo-tx-linux.git / log