Eric Bénard [Tue, 12 Oct 2010 17:26:34 +0000 (19:26 +0200)]
mx25: fix clock's calculation
* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID
* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
During the reorganisation of the imx-i2c devices
(in 64de5ec168d9743903e6ec482c3e9f37af49f9c1) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Dinh Nguyen [Tue, 12 Oct 2010 16:29:01 +0000 (11:29 -0500)]
ARM: imx: Add iram allocator functions
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Peter Korsgaard [Mon, 11 Oct 2010 13:02:06 +0000 (15:02 +0200)]
mxc/gpio: make _set_value work with values != 0/1
Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.
This fix should not hurt already working CPUs, as they are using the written
register value already.
Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.
While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
ARM: mx3/cpuimx35: mark otg_pdata and usbh1_pdata as maybe unused
This fixes
arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used
Sascha Hauer [Wed, 25 Aug 2010 09:56:26 +0000 (11:56 +0200)]
ARM: mx5: clock-imx51: make *ipg clocks secondary clocks of their corresponding peripheral clocks
Currently the uarts and timer only work because they are
turned on by reset default. Make them secondary clocks
of their corresponding peripheral clocks to make sure they
are turned on when necessary. Also, register some clocks
to get rid of compiler warnings
The driver recently learned to handle platform ids. Make use of this
new feature. The up side is that the driver needs less knowledge about
the spi interfaces used on different SoCs.
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX51 comes with two eCSPI interfaces (that are quite different from
what was known before---the tried and tested Freescale way) and a CSPI
interface that is identical to the devices found on i.MX25 and i.MX35.
This patch is a merge of two very similar patches (by Jason Wang and Sascha
Hauer resp.) plus a (now hopefully correct) reimplementation of the
clock calculation.
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
spi/imx: save the spi chip select in config struct, not the gpio to use
This prepares adding support for imx51's eCSPI. This IP has seperate
control and config bits for all four supported chip selects, so the
config routine needs to know which chip select is being used even if
the chipselect is realized by a gpio.
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
spi/imx: get rid of more ifs depending on the used cpu
Nearly everything that is needed is provided by the version of the SPI IP.
Now the only checks left using cpu_is_... are clk divider tuning on mx21/mx27
and autodetection (which will die soon).
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has the advantage not to need to much cpu_is_... macros. Still more
when imx51 support is added which has two different spi interfaces which
would introduce additional checks on the device id.
With this setup it's not possible for the compiler anymore to detect the
unused functions, so four additional kconfig symbols are introduced to
ifdef out the unneeded functions in the callback array and all these
functions are marked with __maybe_unused to suppress the corresponding
gcc warnings.
Comparing the driver footprint with and without the patch for a mx27
kernel yields:
add/remove: 2/0 grow/shrink: 2/0 up/down: 280/0 (280)
function old new delta
spi_imx_devtype - 192 +192
spi_imx_probe 980 1032 +52
spi_imx_devtype_data - 32 +32
spi_imx_setupxfer 276 280 +4
Later when the platform code is updated to use the platform ids, the
autodetection can be removed which will make the driver a bit smaller
again. (~60 Bytes in my test.)
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ARM: imx: change the way spi-imx devices are registered
Group soc specific data in a global struct instead of repeating it for
each call to imxXX_add_spi_imxX. The structs holding the actual data
are placed in .init.constdata and so don't do much harm. Compared to
the previous approach this reduces code size to call imx_add_spi_imx.
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The names used now match the processor's reference manual. Also remove
MXC from the interrupt defines to match the other imx platforms.
Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes the header more look like the other ones, i.e.
- sort #defines by value
- use lowercase hex constants
- use a consistently named header guard
Acked-by: Jason Wang <jason77.wang@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
ARM: mx51_defconfig: add new boards MACH_MX51_3DS and MACH_EUKREA_CPUIMX51
Further remove FIXED_PHY as it breaks the ethernet.
VGA_CONSOLE isn't selectable anymore since fb78b51cb11e.
EXT3_DEFAULTS_TO_ORDERED defaults to y since aa32a796389b.
INOTIFY is gone since 2dfc1cae4c42.
CONFIG_DETECT_SOFTLOCKUP is gone since e16bb1d7fe07.
Enable TMPFS for udev.
KEYS is selected by NFS_USE_KERNEL_DNS
ARM: mx27_defconfig: enable switches used in mx27 code
- enable all mx27 machines (MACH_CPUIMX27, MACH_IMX27_VISSTRIM_M10,
MACH_PCA100, MACH_MXT_TD60) including optional features for
CPUIMX27
- eukrea_mbimx27-baseboard.c uses TOUCHSCREEN_ADS7846
- mach-cpuimx27.c uses SERIAL_8250
- several machines make use of SPI_IMX (selects SPI_BITBANG)
- drop VGA_CONSOLE as this isn't selectable anymore since fb78b51cb11e
- several machines make use of USB_ULPI (depends on USB, but don't
enable USB_DEVICE_CLASS as it's deprecated)
Uwe Kleine-König [Fri, 13 Aug 2010 15:34:05 +0000 (17:34 +0200)]
ARM: imx: ehci: use void __iomem * to hold i/o addresses
This fixes:
arch/arm/plat-mxc/ehci.c: In function 'mxc_initialize_usb_hw':
arch/arm/plat-mxc/ehci.c:260: warning: assignment makes integer from pointer without a cast
arch/arm/plat-mxc/ehci.c:263: warning: assignment makes integer from pointer without a cast
arch/arm/plat-mxc/ehci.c:270: warning: assignment makes integer from pointer without a cast
Randy Dunlap [Sat, 11 Sep 2010 22:55:26 +0000 (15:55 -0700)]
docbook: skip files with no docs since they generate scary warnings
Fix docbook templates that reference files that do not contain the
expected kernel-doc notation.
Fixes these warnings:
Warning(arch/x86/include/asm/unaligned.h): no structured comments found
Warning(lib/vsprintf.c): no structured comments found
These cause errors in the generated html output, like below, so drop
these lines.
Name
arch/x86/include/asm/unaligned.h - Document generation inconsistency
Oops
Warning
The template for this document tried to insert the structured comment from the file arch/x86/include/asm/unaligned.h at this point, but none was found. This dummy section is inserted to allow generation to continue.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Sat, 11 Sep 2010 22:55:22 +0000 (15:55 -0700)]
docbook: warn on unused doc entries
When you don't use !E or !I but only !F, then it's very easy to miss
including some functions, structs etc. in documentation. To help
finding which ones were missed, allow printing out the unused ones as
warnings.
For example, using this on mac80211 yields a lot of warnings like this:
Warning: didn't use docs for DOC: mac80211 workqueue
Warning: didn't use docs for ieee80211_max_queues
Warning: didn't use docs for ieee80211_bss_change
Warning: didn't use docs for ieee80211_bss_conf
when generating the documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Sat, 11 Sep 2010 22:55:12 +0000 (15:55 -0700)]
kernel-doc: ignore case when stripping attributes
There are valid attributes that could have upper case letters, but we
still want to remove, like for example
__attribute__((aligned(NETDEV_ALIGN)))
as encountered in the wireless code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM / Hibernate: Avoid hitting OOM during preallocation of memory
There is a problem in hibernate_preallocate_memory() that it calls
preallocate_image_memory() with an argument that may be greater than
the total number of available non-highmem memory pages. If that's
the case, the OOM condition is guaranteed to trigger, which in turn
can cause significant slowdown to occur during hibernation.
To avoid that, make preallocate_image_memory() adjust its argument
before calling preallocate_image_pages(), so that the total number of
saveable non-highem pages left is not less than the minimum size of
a hibernation image. Change hibernate_preallocate_memory() to try to
allocate from highmem if the number of pages allocated by
preallocate_image_memory() is too low.
Modify free_unnecessary_pages() to take all possible memory
allocation patterns into account.
Reported-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: M. Vefa Bicakci <bicave@superonline.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (28 commits)
ipheth: remove incorrect devtype to WWAN
MAINTAINERS: Add CAIF
sctp: fix test for end of loop
KS8851: Correct RX packet allocation
udp: add rehash on connect()
net: blackhole route should always be recalculated
ipv4: Suppress lockdep-RCU false positive in FIB trie (3)
niu: Fix kernel buffer overflow for ETHTOOL_GRXCLSRLALL
ipvs: fix active FTP
gro: Re-fix different skb headrooms
via-velocity: Turn scatter-gather support back off.
ipv4: Fix reverse path filtering with multipath routing.
UNIX: Do not loop forever at unix_autobind().
PATCH: b44 Handle RX FIFO overflow better (simplified)
irda: off by one
3c59x: Fix deadlock in vortex_error()
netfilter: discard overlapping IPv6 fragment
ipv6: discard overlapping fragment
net: fix tx queue selection for bridged devices implementing select_queue
bonding: Fix jiffies overflow problems (again)
...
Fix up trivial conflicts due to the same cgroup API thinko fix going
through both Andrew and the networking tree. However, there were small
differences between the two, with Andrew's version generally being the
nicer one, and the one I merged first. So pick that one.
Conflicts in: include/linux/cgroup.h and kernel/cgroup.c
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, tsc: Fix a preemption leak in restore_sched_clock_state()
sched: Move sched_avg_update() to update_cpu_load()
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: don't enable self-refresh on Ironlake
drm/i915: Double check that the wait_request is not pending before warning
Revert "drm/i915: Warn if we run out of FIFO space for a mode"
Revert "drm/i915: Allow LVDS on pipe A on gen4+"
Revert "drm/i915: Enable RC6 on Ironlake."
mark gross [Thu, 9 Sep 2010 21:20:09 +0000 (23:20 +0200)]
PM QoS: Correct pr_debug() misuse and improve parameter checks
Correct some pr_debug() misuse and add a stronger parameter check to
pm_qos_write() for the ASCII hex value case. Thanks to Dan Carpenter
for pointing out the problem!
Signed-off-by: mark gross <markgross@thegnar.org> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Dave Chinner [Wed, 8 Sep 2010 09:00:22 +0000 (09:00 +0000)]
xfs: log IO completion workqueue is a high priority queue
The workqueue implementation in 2.6.36-rcX has changed, resulting
in the workqueues no longer having dedicated threads for work
processing. This has caused severe livelocks under heavy parallel
create workloads because the log IO completions have been getting
held up behind metadata IO completions. Hence log commits would
stall, memory allocation would stall because pages could not be
cleaned, and lock contention on the AIL during inode IO completion
processing was being seen to slow everything down even further.
By making the log Io completion workqueue a high priority workqueue,
they are queued ahead of all data/metadata IO completions and
processed before the data/metadata completions. Hence the log never
gets stalled, and operations needed to clean memory can continue as
quickly as possible. This avoids the livelock conditions and allos
the system to keep running under heavy load as per normal.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Elder <aelder@sgi.com>
Roland McGrath [Wed, 8 Sep 2010 02:37:06 +0000 (19:37 -0700)]
execve: make responsive to SIGKILL with large arguments
An execve with a very large total of argument/environment strings
can take a really long time in the execve system call. It runs
uninterruptibly to count and copy all the strings. This change
makes it abort the exec quickly if sent a SIGKILL.
Note that this is the conservative change, to interrupt only for
SIGKILL, by using fatal_signal_pending(). It would be perfectly
correct semantics to let any signal interrupt the string-copying in
execve, i.e. use signal_pending() instead of fatal_signal_pending().
We'll save that change for later, since it could have user-visible
consequences, such as having a timer set too quickly make it so that
an execve can never complete, though it always happened to work before.
Roland McGrath [Wed, 8 Sep 2010 02:36:28 +0000 (19:36 -0700)]
execve: improve interactivity with large arguments
This adds a preemption point during the copying of the argument and
environment strings for execve, in copy_strings(). There is already
a preemption point in the count() loop, so this doesn't add any new
points in the abstract sense.
When the total argument+environment strings are very large, the time
spent copying them can be much more than a normal user time slice.
So this change improves the interactivity of the rest of the system
when one process is doing an execve with very large arguments.
Roland McGrath [Wed, 8 Sep 2010 02:35:49 +0000 (19:35 -0700)]
setup_arg_pages: diagnose excessive argument size
The CONFIG_STACK_GROWSDOWN variant of setup_arg_pages() does not
check the size of the argument/environment area on the stack.
When it is unworkably large, shift_arg_pages() hits its BUG_ON.
This is exploitable with a very large RLIMIT_STACK limit, to
create a crash pretty easily.
Check that the initial stack is not too large to make it possible
to map in any executable. We're not checking that the actual
executable (or intepreter, for binfmt_elf) will fit. So those
mappings might clobber part of the initial stack mapping. But
that is just userland lossage that userland made happen, not a
kernel problem.
Merge branch 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Perform hardware_enable in CPU_STARTING callback
KVM: i8259: fix migration
KVM: fix i8259 oops when no vcpus are online
KVM: x86 emulator: fix regression with cmpxchg8b on i386 hosts
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: t_start: reset FTRACE_ITER_HASH in case of seek/pread
perf symbols: Fix multiple initialization of symbol system
perf: Fix CPU hotplug
perf, trace: Fix module leak
tracing/kprobe: Fix handling of C-unlike argument names
tracing/kprobes: Fix handling of argument names
perf probe: Fix handling of arguments names
perf probe: Fix return probe support
tracing/kprobe: Fix a memory leak in error case
tracing: Do not allow llseek to set_ftrace_filter
David Howells [Fri, 10 Sep 2010 08:59:51 +0000 (09:59 +0100)]
KEYS: Fix bug in keyctl_session_to_parent() if parent has no session keyring
Fix a bug in keyctl_session_to_parent() whereby it tries to check the ownership
of the parent process's session keyring whether or not the parent has a session
keyring [CVE-2010-2960].
If the system is using pam_keyinit then it mostly protected against this as all
processes derived from a login will have inherited the session keyring created
by pam_keyinit during the log in procedure.
To test this, pam_keyinit calls need to be commented out in /etc/pam.d/.
David Howells [Fri, 10 Sep 2010 08:59:46 +0000 (09:59 +0100)]
KEYS: Fix RCU no-lock warning in keyctl_session_to_parent()
There's an protected access to the parent process's credentials in the middle
of keyctl_session_to_parent(). This results in the following RCU warning:
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Range check cpu in blk_cpu_to_group
scatterlist: prevent invalid free when alloc fails
writeback: Fix lost wake-up shutting down writeback thread
writeback: do not lose wakeup events when forking bdi threads
cciss: fix reporting of max queue depth since init
block: switch s390 tape_block and mg_disk to elevator_change()
block: add function call to switch the IO scheduler from a driver
fs/bio-integrity.c: return -ENOMEM on kmalloc failure
bio-integrity.c: remove dependency on __GFP_NOFAIL
BLOCK: fix bio.bi_rw handling
block: put dev->kobj in blk_register_queue fail path
cciss: handle allocation failure
cfq-iosched: Documentation help for new tunables
cfq-iosched: blktrace print per slice sector stats
cfq-iosched: Implement tunable group_idle
cfq-iosched: Do group share accounting in IOPS when slice_idle=0
cfq-iosched: Do not idle if slice_idle=0
cciss: disable doorbell reset on reset_devices
blkio: Fix return code for mkdir calls
Merge branch 'at91-fixes-for-linus' of git://github.com/at91linux/linux-2.6-at91
* 'at91-fixes-for-linus' of git://github.com/at91linux/linux-2.6-at91:
AT91: at91sam9261ek: remove C99 comments but keep information
AT91: at91sam9261ek board: remove warnings related to use of SPI or SD/MMC
AT91: dm9000 initialization update
AT91: SAM9G45 - add a separate clock entry for every single TC block
AT91: clock: peripheral clocks can have other parent than mck
AT91: change dma resource index
projects / linux-beck.git / log