Tejun Heo [Thu, 9 Dec 2010 15:13:15 +0000 (16:13 +0100)]
libata: issue DIPM enable commands with LPM state updated
Low level drivers may behave differently depending on the current
link->lpm_policy. During ata_eh_set_lpm(), DIPM enable commands are
issued after the successful completion of ap->ops->set_lpm(), which
means that the controller is already in the target state. This causes
DIPM enable commands to be processed with mismatching controller power
state and link->lpm_policy value.
In ahci, link->lpm_policy is used to ignore certain PHY events if LPM
is enabled; however, as DIPM commands are issued with stale
link->lpm_policy, they sometimes end up triggering these conditions
and get aborted leading to LPM configuration failure.
Fix it by updating link->lpm_policy before issuing DIPM enable
commands.
Tejun Heo [Thu, 9 Dec 2010 14:59:32 +0000 (15:59 +0100)]
libata: no special completion processing for EH commands
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Wolfram Sang [Wed, 22 Dec 2010 15:50:10 +0000 (16:50 +0100)]
pata_mpc52xx: driver needs BMDMA
Found by this build-error if BMDMA is disabled:
drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...
Wu Zhangjin [Fri, 24 Dec 2010 13:39:08 +0000 (21:39 +0800)]
pata_cs5536: Add support for non-X86_32 platforms
pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS
variant), so, remove the dependency of X86_32 and fix the building
errors under the other platforms via only reserving the X86_32 specific
parts for X86_32.
pata_amd also supports cs5536 IDE controller, but this one saves about
33k for the compressed kernel image(vmlinuz for MIPS).
Signed-off-by: Zhang Le <r0bertz@gentoo.org> Signed-off-by: Chen Jie <chenj@lemote.com> Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 3 Dec 2010 14:19:13 +0000 (15:19 +0100)]
libata-sff: fix HSM_ST_ERR handling in __ata_sff_port_intr()
While separating out BMDMA irq handler from SFF, commit c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().
This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately. Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE. This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Antonio Toma <antonio.toma@gmail.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Tue, 21 Dec 2010 05:34:16 +0000 (21:34 -0800)]
Merge branch 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: gsm_data_alloc buffer allocation could fail and it is not being checked
n_gsm: Fix message length handling when building header
Linus Torvalds [Tue, 21 Dec 2010 05:33:12 +0000 (21:33 -0800)]
Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: gadget: Allow function access to device ID data during bind()"
USB: misc: uss720.c: add another vendor/product ID
USB: usb-storage: unusual_devs entry for the Samsung YP-CP3
USB: gadget: Remove suspended sysfs file before freeing cdev
USB: core: Add input prompt and help text for USB_OTG config
USB: ftdi_sio: Add D.O.Tec PID
xhci: Fix issue with port array setup and buggy hosts.
Linus Torvalds [Tue, 21 Dec 2010 05:32:20 +0000 (21:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: handle partial result from get_user_pages
ceph: mark user pages dirty on direct-io reads
ceph: fix null pointer dereference in ceph_init_dentry for nfs reexport
ceph: fix direct-io on non-page-aligned buffers
ceph: fix msgr_init error path
Linus Torvalds [Mon, 20 Dec 2010 18:35:04 +0000 (10:35 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Linus Torvalds [Mon, 20 Dec 2010 17:49:54 +0000 (09:49 -0800)]
Merge branch 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
OMAP: OMAPFB: disable old omapfb for OMAP4 builds
OMAP: DSS: VRAM: Align start & size of vram to 2M
Linus Torvalds [Mon, 20 Dec 2010 17:46:46 +0000 (09:46 -0800)]
Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV210: update MAX8998 platform data to get rid of WARN()
ARM S3C24XX: Fix compilation of PM code for S3C2416
ARM: S3C24XX: Fix CONFIG_S3C_DEV_NAND Kconfig entry
Linus Torvalds [Mon, 20 Dec 2010 17:19:46 +0000 (09:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
Ingo Molnar [Sun, 19 Dec 2010 22:24:27 +0000 (23:24 +0100)]
sched: Remove debugging check
Linus reported that the new warning introduced by commit f26f9aff6aaf
"Sched: fix skip_clock_update optimization" triggers. The need_resched
flag can be set by other CPUs asynchronously so this debug check is
bogus - remove it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <AANLkTinJ8hAG1TpyC+CSYPR47p48+1=E7fiC45hMXT_1@mail.gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Sun, 19 Dec 2010 18:44:54 +0000 (10:44 -0800)]
Merge branches 'x86-fixes-for-linus' and 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
Linus Torvalds [Sun, 19 Dec 2010 18:37:37 +0000 (10:37 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix the irqtime code for 32bit
sched: Fix the irqtime code to deal with u64 wraps
nohz: Fix get_next_timer_interrupt() vs cpu hotplug
Sched: fix skip_clock_update optimization
sched: Cure more NO_HZ load average woes
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: handle rt_sigreturn() more cleanly
arch/tile: handle CLONE_SETTLS in copy_thread(), not user space
Linus Torvalds [Sat, 18 Dec 2010 18:13:24 +0000 (10:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86: avoid high BIOS area when allocating address space
x86: avoid E820 regions when allocating address space
x86: avoid low BIOS area when allocating address space
resources: add arch hook for preventing allocation in reserved areas
Revert "resources: support allocating space within a region from the top down"
Revert "PCI: allocate bus resources from the top down"
Revert "x86/PCI: allocate space from the end of a region, not the beginning"
Revert "x86: allocate space within a region top-down"
Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
PCI: Update MCP55 quirk to not affect non HyperTransport variants
Chris Metcalf [Tue, 14 Dec 2010 21:07:25 +0000 (16:07 -0500)]
arch/tile: handle rt_sigreturn() more cleanly
The current tile rt_sigreturn() syscall pattern uses the common idiom
of loading up pt_regs with all the saved registers from the time of
the signal, then anticipating the fact that we will clobber the ABI
"return value" register (r0) as we return from the syscall by setting
the rt_sigreturn return value to whatever random value was in the pt_regs
for r0.
However, this breaks in our 64-bit kernel when running "compat" tasks,
since we always sign-extend the "return value" register to properly
handle returned pointers that are in the upper 2GB of the 32-bit compat
address space. Doing this to the sigreturn path then causes occasional
random corruption of the 64-bit r0 register.
Instead, we stop doing the crazy "load the return-value register"
hack in sigreturn. We already have some sigreturn-specific assembly
code that we use to pass the pt_regs pointer to C code. We extend that
code to also set the link register to point to a spot a few instructions
after the usual syscall return address so we don't clobber the saved r0.
Now it no longer matters what the rt_sigreturn syscall returns, and the
pt_regs structure can be cleanly and completely reloaded.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Tue, 14 Dec 2010 20:57:49 +0000 (15:57 -0500)]
arch/tile: handle CLONE_SETTLS in copy_thread(), not user space
Previously we were just setting up the "tp" register in the
new task as started by clone() in libc. However, this is not
quite right, since in principle a signal might be delivered to
the new task before it had its TLS set up. (Of course, this race
window still exists for resetting the libc getpid() cached value
in the new task, in principle. But in any case, we are now doing
this exactly the way all other architectures do it.)
This change is important for 2.6.37 since the tile glibc we will
be submitting upstream will not set TLS in user space any more,
so it will only work on a kernel that has this fix. It should
also be taken for 2.6.36.x in the stable tree if possible.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Cc: stable <stable@kernel.org>
[media] gspca - sonixj: Set the flag for some devices
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
Brandon Philips [Fri, 17 Dec 2010 15:58:22 +0000 (12:58 -0300)]
[media] bttv: remove unneeded locking comments
After Mauro's "bttv: Fix locking issues due to BKL removal code" there
are a number of comments that are no longer needed about lock ordering.
Remove them.
[media] bttv: fix mutex use before init (BZ#24602)
Fix a regression where bttv driver causes oopses when loading, since it
were using some non-initialized mutexes. While it would be possible to
fix the issue, there are some other lock troubles, like to the presence of
lock code at free_btres_lock().
It is possible to fix, but the better is to just use the core-assisted
locking schema. This way, V4L2 core will serialize access to all
ioctl's/open/close/mmap/read/poll operations, avoiding to have two
processes accessing the hardware at the same time. Also, as there's just
one lock, instead of 3, there's no risk of dead locks.
The net result is a cleaner code, with just one lock.
Reported-by: Dan Carpenter <error27@gmail.com> Reported-by: Brandon Philips<brandon@ifup.org> Reported-by: Chris Clayton <chris2553@googlemail.com> Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kevin Cernekee [Wed, 3 Nov 2010 05:28:01 +0000 (22:28 -0700)]
MIPS: Fix build errors in sc-mips.c
Seen with malta_defconfig on Linus' tree:
CC arch/mips/mm/sc-mips.o
arch/mips/mm/sc-mips.c: In function 'mips_sc_is_activated':
arch/mips/mm/sc-mips.c:77: error: 'config2' undeclared (first use in this function)
arch/mips/mm/sc-mips.c:77: error: (Each undeclared identifier is reported only once
arch/mips/mm/sc-mips.c:77: error: for each function it appears in.)
arch/mips/mm/sc-mips.c:81: error: 'tmp' undeclared (first use in this function)
make[2]: *** [arch/mips/mm/sc-mips.o] Error 1
make[1]: *** [arch/mips/mm] Error 2
make: *** [arch/mips] Error 2
[Ralf: Cosmetic changes to minimize the number of arguments passed to
mips_sc_is_activated]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1752/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Bjorn Helgaas [Thu, 16 Dec 2010 17:39:02 +0000 (10:39 -0700)]
x86: avoid high BIOS area when allocating address space
This prevents allocation of the last 2MB before 4GB.
The experiment described here shows Windows 7 ignoring the last 1MB:
https://bugzilla.kernel.org/show_bug.cgi?id=23542#c27
This patch ignores the top 2MB instead of just 1MB because H. Peter Anvin
says "There will be ROM at the top of the 32-bit address space; it's a fact
of the architecture, and on at least older systems it was common to have a
shadow 1 MiB below."
Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bjorn Helgaas [Thu, 16 Dec 2010 17:38:56 +0000 (10:38 -0700)]
x86: avoid E820 regions when allocating address space
When we allocate address space, e.g., to assign it to a PCI device, don't
allocate anything mentioned in the BIOS E820 memory map.
On recent machines (2008 and newer), we assign PCI resources from the
windows described by the ACPI PCI host bridge _CRS. On many Dell
machines, these windows overlap some E820 reserved areas, e.g.,
If we put devices at 0xbff00000, they don't work, probably because
that's really RAM, not I/O memory. This patch prevents that by removing
the 0xbfe4dc00-0xbfffffff area from the "available" resource.
I'm not very happy with this solution because Windows solves the problem
differently (it seems to ignore E820 reserved areas and it allocates
top-down instead of bottom-up; details at comment 45 of the bugzilla
below). That means we're vulnerable to BIOS defects that Windows would not
trip over. For example, if BIOS described a device in ACPI but didn't
mention it in E820, Windows would work fine but Linux would fail.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228 Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bjorn Helgaas [Thu, 16 Dec 2010 17:38:51 +0000 (10:38 -0700)]
x86: avoid low BIOS area when allocating address space
This implements arch_remove_reservations() so allocate_resource() can
avoid any arch-specific reserved areas. This currently just avoids the
BIOS area (the first 1MB), but could be used for E820 reserved areas if
that turns out to be necessary.
We previously avoided this area in pcibios_align_resource(). This patch
moves the test from that PCI-specific path to a generic path, so *all*
resource allocations will avoid this area.
Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bjorn Helgaas [Thu, 16 Dec 2010 17:38:46 +0000 (10:38 -0700)]
resources: add arch hook for preventing allocation in reserved areas
This adds arch_remove_reservations(), which an arch can implement if it
needs to protect part of the address space from allocation.
Sometimes that can be done by just putting a region in the resource tree,
but there are cases where that doesn't work well. For example, x86 BIOS
E820 reservations are not related to devices, so they may overlap part of,
all of, or more than a device resource, so they may not end up at the
correct spot in the resource tree.
Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We're going back to considering bus resources in the order we found
them (in _CRS order, when we're using _CRS), so we don't need to
define any ordering.
Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Henry C Chang [Thu, 16 Dec 2010 04:45:41 +0000 (20:45 -0800)]
ceph: mark user pages dirty on direct-io reads
For read operation, we have to set the argument _write_ of get_user_pages
to 1 since we will write data to pages. Also, we need to SetPageDirty before
releasing these pages.
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com> Signed-off-by: Sage Weil <sage@newdream.net>
Linus Torvalds [Fri, 17 Dec 2010 17:45:25 +0000 (09:45 -0800)]
Merge branch 'for_linus' of git://github.com/at91linux/linux-2.6-at91
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
at91: Refactor Stamp9G20 and PControl G20 board file
at91: Fix uhpck clock rate in upll case
Linus Torvalds [Fri, 17 Dec 2010 17:32:39 +0000 (09:32 -0800)]
Merge branch 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix preemption counter leak in kvm_timer_init()
KVM: enlarge number of possible CPUID leaves
KVM: SVM: Do not report xsave in supported cpuid
KVM: Fix OSXSAVE after migration
Linus Torvalds [Fri, 17 Dec 2010 17:31:59 +0000 (09:31 -0800)]
Merge branch 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Fix pm_runtime_suspended()
PM / Hibernate: Restore old swap signature to avoid user space breakage
PM / Hibernate: Fix PM_POST_* notification with user-space suspend
Linus Torvalds [Fri, 17 Dec 2010 17:27:30 +0000 (09:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix conflict of Mic Boot controls
ALSA: HDA: Enable subwoofer on Asus G73Jw
ALSA: HDA: Fix auto-mute on Lenovo Edge 14
ASoC: Fix bias power down of non-DAPM codec
ASoC: WM8580: Fix R8 initial value
ASoC: fix deemphasis control in wm8904/55/60 codecs
Takashi Iwai [Fri, 17 Dec 2010 14:23:41 +0000 (15:23 +0100)]
ALSA: hda - Fix conflict of Mic Boot controls
Due to the recent change for multiple mics assignment, we need to handle
the index of each Mic Boost control respectively. Otherwise the driver
gets the control element conflicts, and gives the unsable state.
at91: Refactor Stamp9G20 and PControl G20 board file
As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Ryan Mallon [Wed, 2 Jun 2010 00:55:36 +0000 (12:55 +1200)]
at91: Fix uhpck clock rate in upll case
The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix interrupt priority level handling on SH-Mobile ARM.
SH-Mobile ARM platforms using multiple interrupt priority
levels need this patch to fix a potential dead lock that
may occur if multiple interrupts with different levels
are pending simultaneously.
The default INTC configuration is to use the same priority
level for all interrupts, so this issue does not trigger by
default. It is however common for board code to override the
interrupt priority for certain interrupt sources depending
on the application. Without this fix such boards may lock up.
In detail, this patch updates the INTC code in entry-macro.S
to make sure that the INTLVLA register gets set as expected.
To trigger this bug modify the board specific code to adjust
the interrupt priority level for the ethernet chip. After
changing the priority level simply use flood ping to drown
the board with interrupts.
This patch applies to INTCA-based processors such as sh7372,
sh7377 and sh7372. GIC-based processors are not affected.
Suitable for v2.6.37-rc and stable from v2.6.34 to v2.6.36.
Cc: stable@kernel.org Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 15 Dec 2010 10:59:24 +0000 (10:59 +0000)]
ARM: mach-shmobile: fix compile warning in mm/init.c
Turn down the warning noise from the compiler,
basically a SH-Mobile specific version of the
patch located in the RMK patch tracker:
6484/1: "fix compile warning in mm/init.c",
Without this patch the following warning triggers:
CC arch/arm/kernel/sys_arm.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
CC arch/arm/kernel/traps.o
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Takashi YOSHII [Fri, 17 Dec 2010 07:25:09 +0000 (07:25 +0000)]
clocksource: sh_cmt: Remove nested spinlock fix
There are control flow that sh_cmt_set_next() does double
spin-lock. The callers sh_cmt_{start,stop}() already have
lock. But another callers sh_cmt_clock_event_{start,next}()
does not.
Now sh_cmt_set_next() does not lock by itself. All the
callers should hold spin-lock before calling it.
[damm@opensource.se: use __sh_cmt_set_next() to simplify code]
[damm@opensource.se: added stable, suitable for v2.6.35 + v2.6.36] Cc: stable@kernel.org Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If you delete a logical drive, and then run BLKRRPART (e.g. via fdisk)
on a logical drive which is "after" the deleted logical drive in the h->drv[]
array, then cciss_revalidate panics because it will access the null pointer
h->drv[x] when x hits the deleted drive.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Cc: stable@kernel.org Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Mike Snitzer [Fri, 17 Dec 2010 07:34:20 +0000 (08:34 +0100)]
block: max hardware sectors limit wrapper
Implement blk_limits_max_hw_sectors() and make
blk_queue_max_hw_sectors() a wrapper around it.
DM needs this to avoid setting queue_limits' max_hw_sectors and
max_sectors directly. dm_set_device_limits() now leverages
blk_limits_max_hw_sectors() logic to establish the appropriate
max_hw_sectors minimum (PAGE_SIZE). Fixes issue where DM was
incorrectly setting max_sectors rather than max_hw_sectors (which
caused dm_merge_bvec()'s max_hw_sectors check to be ineffective).
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@kernel.org Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@kernel.org Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Marek Szyprowski [Fri, 17 Dec 2010 05:47:42 +0000 (14:47 +0900)]
ARM: S5PV210: update MAX8998 platform data to get rid of WARN()
This patch adds new entries required by the new version of MAX8998
driver. Without them, the driver fails to init. See commit 50f19a4596
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
H. Peter Anvin [Fri, 17 Dec 2010 03:11:09 +0000 (19:11 -0800)]
x86-32: Make sure we can map all of lowmem if we need to
A relocatable kernel can be anywhere in lowmem -- and in the case of a
kdump kernel, is likely to be fairly high. Since the early page
tables map everything from address zero up we need to make sure we
allocate enough brk that we can map all of lowmem if we need to.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Tested-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD3ED.8070607@kernel.org>
Linus Torvalds [Thu, 16 Dec 2010 23:45:49 +0000 (15:45 -0800)]
Merge branch 'for-linus' of git://git.infradead.org/users/eparis/notify
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
fanotify: fill in the metadata_len field on struct fanotify_event_metadata
fanotify: split version into version and metadata_len
fanotify: Dont try to open a file descriptor for the overflow event
fanotify: Introduce FAN_NOFD
fanotify: do not leak user reference on allocation failure
inotify: stop kernel memory leak on file creation failure
fanotify: on group destroy allow all waiters to bypass permission check
fanotify: Dont allow a mask of 0 if setting or removing a mark
fanotify: correct broken ref counting in case adding a mark failed
fanotify: if set by user unset FMODE_NONOTIFY before fsnotify_perm() is called
fanotify: remove packed from access response message
fanotify: deny permissions when no event was sent
Vitaly Kuznetsov [Tue, 14 Dec 2010 15:16:49 +0000 (10:16 -0500)]
USB: usb-storage: unusual_devs entry for the Samsung YP-CP3
Add an unusual_devs entry for the Samsung YP-CP3 MP4 player.
User was getting the following errors in dmesg:
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: USB disconnect, address 2
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb:<2>ldm_validate_partition_table(): Disk read failed.
Dev sdb: unable to read RDB block 0
unable to read partition table
Signed-off-by: Vitaly Kuznetsov <vitty@altlinux.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> CC: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: core: Add input prompt and help text for USB_OTG config
bd6882 commit (usb: gadget: fix Kconfig warning) removes
the duplicate USB_OTG config from gadget/Kconfig. But
does not copy the input prompt and help text to the original
config defined in core/Kconfig. Add them now.
Linus Torvalds [Thu, 16 Dec 2010 23:45:25 +0000 (15:45 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (28 commits)
MIPS: Add a CONFIG_FORCE_MAX_ZONEORDER Kconfig option.
MIPS: LD/SD o32 macro GAS fix update
MIPS: Alchemy: fix build with SERIAL_8250=n
MIPS: Rename mips_dma_cache_sync back to dma_cache_sync
MIPS: MT: Fix typo in comment.
SSB: Fix nvram_get on BCM47xx platform
MIPS: BCM47xx: Swap serial console if ttyS1 was specified.
MIPS: BCM47xx: Use sscanf for parsing mac address
MIPS: BCM47xx: Fill values for b43 into SSB sprom
MIPS: BCM47xx: Do not read config from CFE
MIPS: FDT size is a be32
MIPS: Fix CP0 COUNTER clockevent race
MIPS: Fix regression on BCM4710 processor detection
MIPS: JZ4740: Fix pcm device name
MIPS: Separate two consecutive loads in memset.S
MIPS: Send proper signal and siginfo on FP emulator faults.
MIPS: AR7: Fix loops per jiffies on TNETD7200 devices
MIPS: AR7: Fix double ar7_gpio_init declaration
MIPS: Rework GENERIC_HARDIRQS Kconfig.
MIPS: Alchemy: Add return value check for strict_strtoul()
...
Neil Horman [Wed, 8 Dec 2010 14:47:48 +0000 (09:47 -0500)]
PCI: Update MCP55 quirk to not affect non HyperTransport variants
I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it. Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment. This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.
Ken Mills [Mon, 13 Dec 2010 15:27:27 +0000 (15:27 +0000)]
n_gsm: Fix message length handling when building header
Fix message length handling when building header
When the message length is greater than 127, the length field in the header
is built incorrectly. According to the spec, when the length is less than 128
the length field is a single byte formatted as: bbbbbbb1. When it is greater
than 127 then the field is two bytes of the format: bbbbbbb0bbbbbbbb.
Signed-off-by: Ken Mills <ken.k.mills@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
that fixes a problem with the LD/SD macro currently implemented by GAS for
the o32 ABI in an inconsistent way. This is best illustrated with a
simple program, which I'm copying here from the message above for easier
reference:
The GAS fix makes the macro behave in a consistent way and pairs of LW/SW
instructions to be output as appropriate regardless of the size of the
offset associated with the address used. The machine instruction is still
available, but to reach it macros have to be disabled first. This has a
side effect of requiring the use of a machine-addressable memory operand.
As some platforms require 64-bit operations for accesses to some I/O
registers LD/SD instructions are used in a couple of places in Linux
regardless of the ABI selected. Here's a fix for some pieces of code
affected I've been able to track down. The fix should be backwards
compatible with all supported binutils releases in existence and can be
used as a reference for any other places or off-tree code. The use of the
"R" constraint guarantees a machine-addressable operand.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1680/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Mon, 25 Oct 2010 16:44:11 +0000 (18:44 +0200)]
MIPS: Alchemy: fix build with SERIAL_8250=n
In commit 7d172bfe ("Alchemy: Add UART PM methods") I introduced
platform PM methods which call a function of the 8250 driver;
this patch works around link failures when the kernel is built
without 8250 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1737/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hauke Mehrtens [Sat, 27 Nov 2010 18:26:32 +0000 (19:26 +0100)]
SSB: Fix nvram_get on BCM47xx platform
The nvram_get function was never in the mainline kernel, it only existed in
an external OpenWrt patch. Use nvram_getenv function, which is in mainline
and use an include instead of an extra function declaration. et0macaddr
contains the mac address in text from like 00:11:22:33:44:55. We have to
parse it before adding it into macaddr.
nvram_parse_macaddr will be merged into asm/mach-bcm47xx/nvram.h through
the MIPS git tree and will be available soon. It will not build now without
nvram_parse_macaddr, but it hasn't before either.
Hauke Mehrtens [Sat, 27 Nov 2010 16:46:01 +0000 (17:46 +0100)]
MIPS: BCM47xx: Swap serial console if ttyS1 was specified.
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Hauke Mehrtens [Sat, 27 Nov 2010 16:45:58 +0000 (17:45 +0100)]
MIPS: BCM47xx: Do not read config from CFE
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Kevin Cernekee [Tue, 23 Nov 2010 18:26:44 +0000 (10:26 -0800)]
MIPS: Fix CP0 COUNTER clockevent race
Consider the following test case:
write_c0_compare(read_c0_count());
Even if the counter doesn't increment during execution, this might not
generate an interrupt until the counter wraps around. The CPU may
perform the comparison each time CP0 COUNT increments, not when CP0
COMPARE is written.
If mips_next_event() is called with a very small delta, and CP0 COUNT
increments during the calculation of "cnt += delta", it is possible
that CP0 COMPARE will be written with the current value of CP0 COUNT.
If this is detected, the function should return -ETIME, to indicate
that the interrupt might not have actually gotten scheduled.
Tony Wu [Wed, 10 Nov 2010 13:48:15 +0000 (21:48 +0800)]
MIPS: Separate two consecutive loads in memset.S
partial_fixup is used in noreorder block.
Separating two consecutive loads can save one cycle on processors with
GPR intrelock and can fix load-use on processors that need a load delay slot.
Also do so for fwd_fixup.
[Ralf: Only R2000/R3000 class processors are lacking the the load-user
interlock and even some of those got it retrofitted. With R2000/R3000
being fairly uncommon these days the impact of this bug should be minor.]
Signed-off-by: Tony Wu <tung7970@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1768/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 21 Oct 2010 23:32:26 +0000 (16:32 -0700)]
MIPS: Send proper signal and siginfo on FP emulator faults.
We were unconditionally sending SIGBUS with an empty siginfo on FP
emulator faults. This differs from what happens when real floating
point hardware would get a fault.
For most faults we need to send SIGSEGV with the faulting address
filled in in the struct siginfo.
Reported-by: Camm Maguire <camm@maguirefamily.org> Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1727/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Sun, 31 Oct 2010 22:49:58 +0000 (23:49 +0100)]
MIPS: AR7: Fix loops per jiffies on TNETD7200 devices
TNETD7200 run their CPU clock faster than the default CPU clock we assume.
In order to have the correct loops per jiffies settings, initialize clocks right
before setting mips_hpt_frequency. As a side effect, we can no longer use
msleep in clocks.c which requires other parts of the kernel to be initialized,
so replace these with mdelay.
Yoichi Yuasa [Mon, 8 Nov 2010 08:23:52 +0000 (17:23 +0900)]
MIPS: Alchemy: Add return value check for strict_strtoul()
arch/mips/alchemy/devboards/prom.c: In function 'prom_init':
arch/mips/alchemy/devboards/prom.c:60: error: ignoring return value of
'strict_strtoul', declared with attribute warn_unused_result
Wu Zhangjin [Mon, 8 Nov 2010 13:25:24 +0000 (21:25 +0800)]
MIPS: Loongson: Add return value check for strict_strtoul()
cc1: warnings being treated as errors
arch/mips/loongson/common/env.c: In function 'prom_init_env':
arch/mips/loongson/common/env.c:49: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:50: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:51: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:52: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
Jesper Juhl [Sat, 30 Oct 2010 16:37:16 +0000 (18:37 +0200)]
MIPS: VPE loader: Check vmalloc return value in vpe_open
The return value of the vmalloc() call in arch/mips/kernel/vpe.c::vpe_open()
is not checked, so we potentially store a null pointer in v->pbuffer. Add
a check for a null return and then return -ENOMEM in that case.
[Ralf: The check added by Jesper's original patch is where it logically
should be. Adding it eleminated the need for the checks in a few other
places, so I removed them. There still is a zillion of other things that
need to be fixed in this file / API.]