While the bonding module is unloading, it is considered that after
rtnl_link_unregister all bond devices are destroyed but since no
synchronization mechanism exists, a new bond device can be created
via bonding_masters before unregister_pernet_subsys which would
lead to multiple problems (e.g. NULL pointer dereference, wrong RIP,
list corruption).
This patch fixes the issue by removing any bond devices left in the
netns after bonding_masters is removed from sysfs.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few drivers use dev_uc_sync/unsync to synchronize the
address lists from master down to slave/lower devices. In
some cases (bond/team) a single address list is synched down
to multiple devices. At the time of unsync, we have a leak
in these lower devices, because "synced" is treated as a
boolean and the address will not be unsynced for anything after
the first device/call.
Treat "synced" as a count (same as refcount) and allow all
unsync calls to work.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IPv6 Routing table becomes broken once we do ifdown, ifup of the loopback(lo)
interface. After down-up, routes of other interface's IPv6 addresses through
'lo' are lost.
IPv6 addresses assigned to all interfaces are routed through 'lo' for internal
communication. Once 'lo' is down, those routing entries are removed from routing
table. But those removed entries are not being re-created properly when 'lo' is
brought up. So IPv6 addresses of other interfaces becomes unreachable from the
same machine. Also this breaks communication with other machines because of
NDISC packet processing failure.
This patch fixes this issue by reading all interface's IPv6 addresses and adding
them to IPv6 routing table while bringing up 'lo'.
==Testing==
Before applying the patch:
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
After applying the patch:
$ route -A inet6
Kernel IPv6 routing
table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
Signed-off-by: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> Signed-off-by: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link
In shaper | Actual Result
-----------+---------------
100M | 108 Mbps
200M | 244 Mbps
300M | 412 Mbps
500M | 893 Mbps
This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.
To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org> Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in set_orig_addr() does not initialize all of the members of
struct sockaddr_tipc when filling the sockaddr info -- namely the union
is only partly filled. This will make recv_msg() and recv_stream() --
the only users of this function -- leak kernel stack memory as the
msg_name member is a local variable in net/socket.c.
Additionally to that both recv_msg() and recv_stream() fail to update
the msg_namelen member to 0 while otherwise returning with 0, i.e.
"success". This is the case for, e.g., non-blocking sockets. This will
lead to a 128 byte kernel stack leak in net/socket.c.
Fix the first issue by initializing the memory of the union with
memset(0). Fix the second one by setting msg_namelen to 0 early as it
will be updated later if we're going to fill the msg_name member.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in rose_recvmsg() does not initialize all of the members of
struct sockaddr_rose/full_sockaddr_rose when filling the sockaddr info.
Nor does it initialize the padding bytes of the structure inserted by
the compiler for alignment. This will lead to leaking uninitialized
kernel stack bytes in net/socket.c.
Fix the issue by initializing the memory used for sockaddr info with
memset(0).
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in llcp_sock_recvmsg() does not initialize all the members of
struct sockaddr_nfc_llcp when filling the sockaddr info. Nor does it
initialize the padding bytes of the structure inserted by the compiler
for alignment.
Also, if the socket is in state LLCP_CLOSED or is shutting down during
receive the msg_namelen member is not updated to 0 while otherwise
returning with 0, i.e. "success". The msg_namelen update is also
missing for stream and seqpacket sockets which don't fill the sockaddr
info.
Both issues lead to the fact that the code will leak uninitialized
kernel stack bytes in net/socket.c.
Fix the first issue by initializing the memory used for sockaddr info
with memset(0). Fix the second one by setting msg_namelen to 0 early.
It will be updated later if we're going to fill the msg_name member.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org> Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case msg_name is set the sockaddr info gets filled out, as
requested, but the code fails to initialize the padding bytes of
struct sockaddr_ax25 inserted by the compiler for alignment. Also
the sax25_ndigis member does not get assigned, leaking four more
bytes.
Both issues lead to the fact that the code will leak uninitialized
kernel stack bytes in net/socket.c.
Fix both issues by initializing the memory with memset(0).
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For stream sockets the code misses to update the msg_namelen member
to 0 and therefore makes net/socket.c leak the local, uninitialized
sockaddr_storage variable to userland -- 128 bytes of kernel stack
memory. The msg_namelen update is also missing for datagram sockets
in case the socket is shutting down during receive.
Fix both issues by setting msg_namelen to 0 early. It will be
updated later if we're going to fill the msg_name member.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The L2TP code for IPv6 fails to initialize the l2tp_conn_id member of
struct sockaddr_l2tpip6 and therefore leaks four bytes kernel stack
in l2tp_ip6_recvmsg() in case msg_name is set.
Initialize l2tp_conn_id with 0 to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about iucv_sock_recvmsg() not filling the msg_name in case it was set.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about irda_recvmsg_dgram() not filling the msg_name in case it was
set.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about caif_seqpkt_recvmsg() not filling the msg_name in case it was
set.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the socket is in state BT_CONNECT2 and BT_SK_DEFER_SETUP is set in
the flags, sco_sock_recvmsg() returns early with 0 without updating the
possibly set msg_namelen member. This, in turn, leads to a 128 byte
kernel stack leak in net/socket.c.
Fix this by updating msg_namelen in this case. For all other cases it
will be handled in bt_sock_recvmsg().
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RFCOMM_DEFER_SETUP is set in the flags, rfcomm_sock_recvmsg() returns
early with 0 without updating the possibly set msg_namelen member. This,
in turn, leads to a 128 byte kernel stack leak in net/socket.c.
Fix this by updating msg_namelen in this case. For all other cases it
will be handled in bt_sock_stream_recvmsg().
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the socket is already shutting down, bt_sock_recvmsg() returns
with 0 without updating msg_namelen leading to net/socket.c leaking the
local, uninitialized sockaddr_storage variable to userland -- 128 bytes
of kernel stack memory.
Fix this by moving the msg_namelen assignment in front of the shutdown
test.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When msg_namelen is non-zero the sockaddr info gets filled out, as
requested, but the code fails to initialize the padding bytes of struct
sockaddr_ax25 inserted by the compiler for alignment. Additionally the
msg_namelen value is updated to sizeof(struct full_sockaddr_ax25) but is
not always filled up to this size.
Both issues lead to the fact that the code will leak uninitialized
kernel stack bytes in net/socket.c.
Fix both issues by initializing the memory with memset(0).
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not fill the msg_name member in case it is set.
It also does not set the msg_namelen member to 0 and therefore makes
net/socket.c leak the local, uninitialized sockaddr_storage variable
to userland -- 128 bytes of kernel stack memory.
Fix that by simply setting msg_namelen to 0 as obviously nobody cared
about vcc_recvmsg() not filling the msg_name in case it was set.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dave Kleikamp, when we emit cross calls to do batched
TLB flush processing we have a race because we do not synchronize on
the sibling cpus completing the cross call.
So meanwhile the TLB batch can be reset (tb->tlb_nr set to zero, etc.)
and either flushes are missed or flushes will flush the wrong
addresses.
Fix this by using generic infrastructure to synchonize on the
completion of the cross call.
This first required getting the flush_tlb_pending() call out from
switch_to() which operates with locks held and interrupts disabled.
The problem is that smp_call_function_many() cannot be invoked with
IRQs disabled and this is explicitly checked for with WARN_ON_ONCE().
We get the batch processing outside of locked IRQ disabled sections by
using some ideas from the powerpc port. Namely, we only batch inside
of arch_{enter,leave}_lazy_mmu_mode() calls. If we're not in such a
region, we flush TLBs synchronously.
1) Get rid of xcall_flush_tlb_pending and per-cpu type
implementations.
a) Add 'active' member to struct tlb_batch
b) Define __HAVE_ARCH_ENTER_LAZY_MMU_MODE
c) Set 'active' in arch_enter_lazy_mmu_mode()
d) Run batch and clear 'active' in arch_leave_lazy_mmu_mode()
e) Check 'active' in tlb_batch_add_one() and do a synchronous
flush if it's clear.
4) Add infrastructure for synchronous TLB page flushes.
a) Implement __flush_tlb_page and per-cpu variants, patch
as needed.
b) Likewise for xcall_flush_tlb_page.
c) Implement smp_flush_tlb_page() to invoke the cross-call.
d) Wire up global_flush_tlb_page() to the right routine based
upon CONFIG_SMP
5) It turns out that singleton batches are very common, 2 out of every
3 batch flushes have only a single entry in them.
The batch flush waiting is very expensive, both because of the poll
on sibling cpu completeion, as well as because passing the tlb batch
pointer to the sibling cpus invokes a shared memory dereference.
Therefore, in flush_tlb_pending(), if there is only one entry in
the batch perform a completely asynchronous global_flush_tlb_page()
instead.
Reported-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit b0de59b5733d ("TTY: do not update atime/mtime on read/write")
we removed timestamps from tty inodes to fix a security issue and waited
if something breaks. Well, 'w', the utility to find out logged users
and their inactivity time broke. It shows that users are inactive since
the time they logged in.
To revert to the old behaviour while still preventing attackers to
guess the password length, we update the timestamps in one-minute
intervals by this patch.
On http://vladz.devzero.fr/013_ptmx-timing.php, we can see how to find
out length of a password using timestamps of /dev/ptmx. It is
documented in "Timing Analysis of Keystrokes and Timing Attacks on
SSH". To avoid that problem, do not update time when reading
from/writing to a TTY.
I am afraid of regressions as this is a behavior we have since 0.97
and apps may expect the time to be current, e.g. for monitoring
whether there was a change on the TTY. Now, there is no change. So
this would better have a lot of testing before it goes upstream.
Nothing is using it yet, but this will allow us to delay the open-time
checks to use time, without breaking the normal UNIX permission
semantics where permissions are determined by the opener (and the file
descriptor can then be passed to a different process, or the process can
drop capabilities).
lmo commit c17a6554 (MIPS: page.h: Provide more readable definition for
PAGE_MASK) apparently breaks ioremap of 36-bit addresses on my Alchemy
systems (PCI and PCMCIA) The reason is that in arch/mips/mm/ioremap.c
line 157 (phys_addr &= PAGE_MASK) bits 32-35 are cut off. Seems the
new PAGE_MASK is explicitly 32bit, or one could make it signed instead
of unsigned long.
Commit b4cbb197c7e7 ("vm: add vm_iomap_memory() helper function") added
a helper function wrapper around io_remap_pfn_range(), and every other
architecture defined it in <asm/pgtable.h>.
The s390 choice of <asm/io.h> may make sense, but is not very convenient
for this case, and gratuitous differences like that cause unexpected errors like this:
mm/memory.c: In function 'vm_iomap_memory':
mm/memory.c:2439:2: error: implicit declaration of function 'io_remap_pfn_range' [-Werror=implicit-function-declaration]
Glory be the kbuild test robot who noticed this, bisected it, and
reported it to the guilty parties (ie me).
While trying to track down a tree log replay bug I noticed that fsck was always
complaining about nbytes not being right for our fsynced file. That is because
the new fsync stuff doesn't wait for ordered extents to complete, so the inodes
nbytes are not necessarily updated properly when we log it. So to fix this we
need to set nbytes to whatever it is on the inode that is on disk, so when we
replay the extents we can just add the bytes that are being added as we replay
the extent. This makes it work for the case that we have the wrong nbytes or
the case that we logged everything and nbytes is actually correct. With this
I'm no longer getting nbytes errors out of btrfsck.
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com> Signed-off-by: Lingzhu Xiang <lxiang@redhat.com> Reviewed-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is my example conversion of a few existing mmap users. The mtdchar
case is actually disabled right now (and stays disabled), but I did it
because it showed up on my "git grep", and I was familiar with the code
due to fixing an overflow problem in the code in commit 9c603e53d380
("mtdchar: fix offset overflow detection").
This is my example conversion of a few existing mmap users. The HPET
case is simple, widely available, and easy to test (Clemens Ladisch sent
a trivial test-program for it).
This is my example conversion of a few existing mmap users. The
fb_mmap() case is a good example because it is a bit more complicated
than some: fb_mmap() mmaps one of two different memory areas depending
on the page offset of the mmap (but happily there is never any mixing of
the two, so the helper function still works).
Various drivers end up replicating the code to mmap() their memory
buffers into user space, and our core memory remapping function may be
very flexible but it is unnecessarily complicated for the common cases
to use.
Our internal VM uses pfn's ("page frame numbers") which simplifies
things for the VM, and allows us to pass physical addresses around in a
denser and more efficient format than passing a "phys_addr_t" around,
and having to shift it up and down by the page size. But it just means
that drivers end up doing that shifting instead at the interface level.
It also means that drivers end up mucking around with internal VM things
like the vma details (vm_pgoff, vm_start/end) way more than they really
need to.
So this just exports a function to map a certain physical memory range
into user space (using a phys_addr_t based interface that is much more
natural for a driver) and hides all the complexity from the driver.
Some drivers will still end up tweaking the vm_page_prot details for
things like prefetching or cacheability etc, but that's actually
relevant to the driver, rather than caring about what the page offset of
the mapping is into the particular IO memory region.
Changing uid/gid/projid mappings doesn't change your id within the
namespace; it reconfigures the namespace. Unprivileged programs should
*not* be able to write these files. (We're also checking the privileges
on the wrong task.)
Given the write-once nature of these files and the other security
checks, this is likely impossible to usefully exploit.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we require privilege for setting /proc/<pid>/uid_map or
/proc/<pid>/gid_map no longer allow an unprivileged user to
open the file and pass it to a privileged program to write
to the file.
Instead when privilege is required require both the opener and the
writer to have the necessary capabilities.
I have tested this code and verified that setting /proc/<pid>/uid_map
fails when an unprivileged user opens the file and a privielged user
attempts to set the mapping, that unprivileged users can still map
their own id, and that a privileged users can still setup an arbitrary
mapping.
Reported-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The valid mask for both offcore_response_0 and
offcore_response_1 was wrong for SNB/SNB-EP,
IVB/IVB-EP. It was possible to write to
reserved bit and cause a GP fault crashing
the kernel.
This patch fixes the problem by correctly marking the
reserved bits in the valid mask for all the processors
mentioned above.
A distinction between desktop and server parts is introduced
because bits 24-30 are only available on the server parts.
This version of the patch is just a rebase to perf/urgent tree
and should apply to older kernels as well.
Trinity discovered that we fail to check all 64 bits of
attr.config passed by user space, resulting to out-of-bounds
access of the perf_swevent_enabled array in
sw_perf_event_destroy().
Introduced in commit b0a873ebb ("perf: Register PMU
implementations").
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Link: http://lkml.kernel.org/r/1365882554-30259-1-git-send-email-tt.rantala@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not set the msg_namelen member to 0 and therefore
makes net/socket.c leak the local sockaddr_storage variable to userland
-- 128 bytes of kernel stack memory. Fix that.
And make use of it in b43. This fixes a regression introduced with 49d55cef5b1925a5c1efb6aaddaa40fc7c693335
b43: N-PHY: implement spurious tone avoidance
This commit made BCM4322 use only MCS 0 on channel 13, which of course
resulted in performance drop (down to 0.7Mb/s).
Reported-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If authentication (or association with FT) is requested by
userspace, mac80211 currently doesn't tell cfg80211 that it
disconnected from the AP. That leaves inconsistent state:
cfg80211 thinks it's connected while mac80211 thinks it's
not. Typically this won't last long, as soon as mac80211
reports the new association to cfg80211 the old one goes
away. If, however, the new authentication or association
doesn't succeed, then cfg80211 will forever think the old
one still exists and will refuse attempts to authenticate
or associate with the AP it thinks it's connected to.
Anders reported that this leads to it taking a very long
time to reconnect to a network, or never even succeeding.
I tested this with an AP hacked to never respond to auth
frames, and one that works, and with just those two the
system never recovers because one won't work and cfg80211
thinks it's connected to the other so refuses connections
to it.
To fix this, simply make mac80211 tell cfg80211 when it is
no longer connected to the old AP, while authenticating or
associating to a new one.
Reported-by: Anders Kaseorg <andersk@mit.edu> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware parsing of Control Wrapper Frames needs to be disabled, as
it has been causing spurious decryption error reports. The initvals for
other chips have been updated to disable it, but AR9580 was left out for
some reason.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the firmware has been open sourced, the minor version has been
bumped to 1.4 and the API/ABI will stay compatible across further 1.x
releases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Events may be created with attr->disabled == 1 and attr->enable_on_exec
== 1, which confuses the group validation code because events with the
PERF_EVENT_STATE_OFF are not considered candidates for scheduling, which
may lead to failure at group scheduling time.
This patch fixes the validation check for ARM, so that events in the
OFF state are still considered when enable_on_exec is true.
Reported-by: Sudeep KarkadaNagesha <Sudeep.KarkadaNagesha@arm.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Feroceon the L2 cache becomes non-coherent with the CPU
when the L1 caches are disabled. Thus the L2 needs to be invalidated
after both L1 caches are disabled.
On kexec before the starting the code for relocation the kernel,
the L1 caches are disabled in cpu_froc_fin (cpu_v7_proc_fin for Feroceon),
but after L2 cache is never invalidated, because inv_all is not set
in cache-feroceon-l2.c.
So kernel relocation and decompression may has (and usually has) errors.
Setting the function enables L2 invalidation and fixes the issue.
Signed-off-by: Illia Ragozin <illia.ragozin@grapecom.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
try_to_wake_up_local() should only be invoked to wake up another
task in the same runqueue and BUG_ON()s are used to enforce the
rule. Missing try_to_wake_up_local() can stall workqueue
execution but such stalls are likely to be finite either by
another work item being queued or the one blocked getting
unblocked. There's no reason to trigger BUG while holding rq
lock crashing the whole system.
Convert BUG_ON()s in try_to_wake_up_local() to WARN_ON_ONCE()s.
- For the 57766 and non Ax versions of 57765, bootcode needs to setup
the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
Unfortunately, it does not have enough room in the selfboot case (i.e.
devices with no NVRAM). The driver needs to implement this.
- For performance reasons, the 2k DMA engine mode on the 57766 should
be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables iomuxc_gate clock. It is necessary to be able to
reconfigure iomux pads. Without this clock enabled, the
clk_disable_unused function will disable this clock and the iomux pads
are not configurable anymore. This happens at every boot. After a reboot
(watchdog system reset) the clock is not enabled again, so all iomux pad
reconfigurations in boot code are without effect.
The iomux pads should be always configurable, so this patch always
enables it.
The i.MX35 has two bits per clock gate which are decoded as follows:
0b00 -> clock off
0b01 -> clock is on in run mode, off in wait/doze
0b10 -> clock is on in run/wait mode, off in doze
0b11 -> clock is always on
The reset value for the MAX clock is 0b10.
The MAX clock is needed by the SoC, yet unused in the Kernel, so the
common clock framework will disable it during late init time. It will
only disable clocks though which it detects as being turned on. This
detection is made depending on the lower bit of the gate. If the reset
value has been altered by the bootloader to 0b11 the clock framework
will detect the clock as turned on, yet unused, hence it will turn it
off and the system locks up.
This patch turns the MAX clock on unconditionally making the Kernel
independent of the bootloader.
This patch adds support for kvm_gfn_to_hva_cache_init functions for
reads and writes that will cross a page. If the range falls within
the same memslot, then this will be a fast operation. If the range
is split between two memslots, then the slower kvm_read_guest and
kvm_write_guest are used.
Tested: Test against kvm_clock unit tests.
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Gleb Natapov <gleb@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the guest specifies a IOAPIC_REG_SELECT with an invalid value and follows
that with a read of the IOAPIC_REG_WINDOW KVM does not properly validate
that request. ioapic_read_indirect contains an
ASSERT(redir_index < IOAPIC_NUM_PINS), but the ASSERT has no effect in
non-debug builds. In recent kernels this allows a guest to cause a kernel
oops by reading invalid memory. In older kernels (pre-3.3) this allows a
guest to read from large ranges of host memory.
Tested: tested against apic unit tests.
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential use after free issue with the handling of
MSR_KVM_SYSTEM_TIME. If the guest specifies a GPA in a movable or removable
memory such as frame buffers then KVM might continue to write to that
address even after it's removed via KVM_SET_USER_MEMORY_REGION. KVM pins
the page in memory so it's unlikely to cause an issue, but if the user
space component re-purposes the memory previously used for the guest, then
the guest will be able to corrupt that memory.
Tested: Tested against kvmclock unit test
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the guest sets the GPA of the time_page so that the request to update the
time straddles a page then KVM will write onto an incorrect page. The
write is done byusing kmap atomic to get a pointer to the page for the time
structure and then performing a memcpy to that page starting at an offset
that the guest controls. Well behaved guests always provide a 32-byte aligned
address, however a malicious guest could use this to corrupt host kernel
memory.
Tested: Tested against kvmclock unit test.
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documentation/filesystems/proc.txt says about coredump_filter bitmask,
Note bit 0-4 doesn't effect any hugetlb memory. hugetlb memory are only
effected by bit 5-6.
However current code can go into the subsequent flag checks of bit 0-4
for vma(VM_HUGETLB). So this patch inserts 'return' and makes it work
as written in the document.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Michal Hocko <mhocko@suse.cz> Reviewed-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With applying the previous patch "hugetlbfs: stop setting VM_DONTDUMP in
initializing vma(VM_HUGETLB)" to reenable hugepage coredump, if a memory
error happens on a hugepage and the affected processes try to access the
error hugepage, we hit VM_BUG_ON(atomic_read(&page->_count) <= 0) in
get_page().
The reason for this bug is that coredump-related code doesn't recognise
"hugepage hwpoison entry" with which a pmd entry is replaced when a memory
error occurs on a hugepage.
In other words, physical address information is stored in different bit
layout between hugepage hwpoison entry and pmd entry, so
follow_hugetlb_page() which is called in get_dump_page() returns a wrong
page from a given address.
With this patch, we can call hugetlb_fault() and take proper actions (we
wait for migration entries, fail with VM_FAULT_HWPOISON_LARGE for
hwpoisoned entries,) and as the result we can dump all hugepages except
for hwpoisoned ones.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Rik van Riel <riel@redhat.com> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we fail to include any data on hugepages into coredump,
because VM_DONTDUMP is set on hugetlbfs's vma. This behavior was
recently introduced by commit 314e51b9851b ("mm: kill vma flag
VM_RESERVED and mm->reserved_vm counter").
This looks to me a serious regression, so let's fix it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Michal Hocko <mhocko@suse.cz> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To get correct endianes on little endian cpus (like arm) while reading device
tree properties, this patch replaces of_get_property() with
of_property_read_u32(). While there use of_property_read_bool() for the
handling of the boolean "nxp,no-comparator-bypass" property.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
threaded irqs must provide a primary handler or set the IRQF_ONESHOT flag.
Since the mcp251x driver doesn't make use of a primary handler set the
IRQF_ONESHOT flag.
The current code makes the assumption that a cpu_base lock won't be
held if the CPU corresponding to that cpu_base is offline, which isn't
always true.
If a hrtimer is not queued, then it will not be migrated by
migrate_hrtimers() when a CPU is offlined. Therefore, the hrtimer's
cpu_base may still point to a CPU which has subsequently gone offline
if the timer wasn't enqueued at the time the CPU went down.
Normally this wouldn't be a problem, but a cpu_base's lock is blindly
reinitialized each time a CPU is brought up. If a CPU is brought
online during the period that another thread is performing a hrtimer
operation on a stale hrtimer, then the lock will be reinitialized
under its feet, and a SPIN_BUG() like the following will be observed:
<0>[ 28.082085] BUG: spinlock already unlocked on CPU#0, swapper/0/0
<0>[ 28.087078] lock: 0xc4780b40, value 0x0 .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
<4>[ 42.451150] [<c0014398>] (unwind_backtrace+0x0/0x120) from [<c0269220>] (do_raw_spin_unlock+0x44/0xdc)
<4>[ 42.460430] [<c0269220>] (do_raw_spin_unlock+0x44/0xdc) from [<c071b5bc>] (_raw_spin_unlock+0x8/0x30)
<4>[ 42.469632] [<c071b5bc>] (_raw_spin_unlock+0x8/0x30) from [<c00a9ce0>] (__hrtimer_start_range_ns+0x1e4/0x4f8)
<4>[ 42.479521] [<c00a9ce0>] (__hrtimer_start_range_ns+0x1e4/0x4f8) from [<c00aa014>] (hrtimer_start+0x20/0x28)
<4>[ 42.489247] [<c00aa014>] (hrtimer_start+0x20/0x28) from [<c00e6190>] (rcu_idle_enter_common+0x1ac/0x320)
<4>[ 42.498709] [<c00e6190>] (rcu_idle_enter_common+0x1ac/0x320) from [<c00e6440>] (rcu_idle_enter+0xa0/0xb8)
<4>[ 42.508259] [<c00e6440>] (rcu_idle_enter+0xa0/0xb8) from [<c000f268>] (cpu_idle+0x24/0xf0)
<4>[ 42.516503] [<c000f268>] (cpu_idle+0x24/0xf0) from [<c06ed3c0>] (rest_init+0x88/0xa0)
<4>[ 42.524319] [<c06ed3c0>] (rest_init+0x88/0xa0) from [<c0c00978>] (start_kernel+0x3d0/0x434)
As an example, this particular crash occurred when hrtimer_start() was
executed on CPU #0. The code locked the hrtimer's current cpu_base
corresponding to CPU #1. CPU #0 then tried to switch the hrtimer's
cpu_base to an optimal CPU which was online. In this case, it selected
the cpu_base corresponding to CPU #3.
Before it could proceed, CPU #1 came online and reinitialized the
spinlock corresponding to its cpu_base. Thus now CPU #0 held a lock
which was reinitialized. When CPU #0 finally ended up unlocking the
old cpu_base corresponding to CPU #1 so that it could switch to CPU
#3, we hit this SPIN_BUG() above while in switch_hrtimer_base().
CPU #0 CPU #1
---- ----
... <offline>
hrtimer_start()
lock_hrtimer_base(base #1)
... init_hrtimers_cpu()
switch_hrtimer_base() ...
... raw_spin_lock_init(&cpu_base->lock)
raw_spin_unlock(&cpu_base->lock) ...
<spin_bug>
The smpboot threads rely on the park/unpark mechanism which binds per
cpu threads on a particular core. Though the functionality is racy:
CPU0 CPU1 CPU2
unpark(T) wake_up_process(T)
clear(SHOULD_PARK) T runs
leave parkme() due to !SHOULD_PARK
bind_to(CPU2) BUG_ON(wrong CPU)
We cannot let the tasks move themself to the target CPU as one of
those tasks is actually the migration thread itself, which requires
that it starts running on the target cpu right away.
The solution to this problem is to prevent wakeups in park mode which
are not from unpark(). That way we can guarantee that the association
of the task to the target cpu is working correctly.
Add a new task state (TASK_PARKED) which prevents other wakeups and
use this state explicitly for the unpark wakeup.
Peter noticed: Also, since the task state is visible to userspace and
all the parked tasks are still in the PID space, its a good hint in ps
and friends that these tasks aren't really there for the moment.
The sched_set_stop_task() call is issued while the task is on the
runqueue of CPU1 and that confuses the hell out of the stop_task class
on that cpu. So we need the same synchronizaion before
sched_set_stop_task().
Reported-by: Dave Jones <davej@redhat.com> Reported-and-tested-by: Dave Hansen <dave@sr71.net> Reported-and-tested-by: Borislav Petkov <bp@alien8.de> Acked-by: Peter Ziljstra <peterz@infradead.org> Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Cc: dhillf@gmail.com Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1304091635430.21884@ionos Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing check handles the case where we've migrated to a different
core than we last ran on, but it doesn't handle the case where we're
still on the same cpu we last ran on, but some other vcpu has run on
this cpu in the meantime.
Without this, guest segfaults (and other misbehavior) have been seen in
smp guests.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A label 0 was missed in the patch a9c4e541 (powerpc/kprobe: Complete
kprobe and migrate exception frame). This will cause the kernel
branch to an undetermined address if there really has a conflict when
updating the thread flags.
Signed-off-by: Kevin Hao <haokexin@gmail.com> Acked-By: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlier version of this patch took the ldisc_mutex since the other
user of tty_ldisc_flush_works() (tty_set_ldisc()) did this.
Peter Hurley then said that it is should not be requried. Since it
wasn't done earlier, I dropped this part.
The code under tty_ldisc_kill() was executed earlier with the tty lock
taken so it is taken again.
I was able to reproduce the deadlock on v3.8-rc1, this patch fixes the
problem in my testcase. I didn't notice any problems so far.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Alan Cox <alan@linux.intel.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Bryan O'Donoghue <bryan.odonoghue.lkml@nexus-software.ie> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoking arch_flush_lazy_mmu_mode() results in calls to
preempt_enable()/disable() which may have performance impact.
Since lazy MMU is not used on bare metal we can patch away
arch_flush_lazy_mmu_mode() so that it is never called in such
environment.
[ hpa: the previous patch "Fix vmalloc_fault oops during lazy MMU
updates" may cause a minor performance regression on
bare metal. This patch resolves that performance regression. It is
somewhat unclear to me if this is a good -stable candidate. ]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: http://lkml.kernel.org/r/1364045796-10720-2-git-send-email-konrad.wilk@oracle.com Tested-by: Josh Boyer <jwboyer@redhat.com> Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In paravirtualized x86_64 kernels, vmalloc_fault may cause an oops
when lazy MMU updates are enabled, because set_pgd effects are being
deferred.
One instance of this problem is during process mm cleanup with memory
cgroups enabled. The chain of events is as follows:
- zap_pte_range enables lazy MMU updates
- zap_pte_range eventually calls mem_cgroup_charge_statistics,
which accesses the vmalloc'd mem_cgroup per-cpu stat area
- vmalloc_fault is triggered which tries to sync the corresponding
PGD entry with set_pgd, but the update is deferred
- vmalloc_fault oopses due to a mismatch in the PUD entries
The sched_clock_remote() implementation has the following inatomicity
problem on 32bit systems when accessing the remote scd->clock, which
is a 64bit value.
While the update of scd->clock is using an atomic64 mechanism, the
readout on the remote cpu is not, which can cause completely bogus
readouts.
It is a quite rare problem, because it requires the update to hit the
narrow race window between the low/high readout and the update must go
across the 32bit boundary.
The resulting misbehaviour is, that CPU1 will see the sched_clock on
CPU1 ~4 seconds ahead of it's own and update CPU1s sched_clock value
to this bogus timestamp. This stays that way due to the clamping
implementation for about 4 seconds until the synchronization with
CLOCK_MONOTONIC undoes the problem.
The issue is hard to observe, because it might only result in a less
accurate SCHED_OTHER timeslicing behaviour. To create observable
damage on realtime scheduling classes, it is necessary that the bogus
update of CPU1 sched_clock happens in the context of an realtime
thread, which then gets charged 4 seconds of RT runtime, which results
in the RT throttler mechanism to trigger and prevent scheduling of RT
tasks for a little less than 4 seconds. So this is quite unlikely as
well.
The issue was quite hard to decode as the reproduction time is between
2 days and 3 weeks and intrusive tracing makes it less likely, but the
following trace recorded with trace_clock=global, which uses
sched_clock_local(), gave the final hint:
What happens is that CPU0 goes idle and invokes
sched_clock_idle_sleep_event() which invokes sched_clock_local() and
CPU1 runs a remote wakeup for CPU0 at the same time, which invokes
sched_remote_clock(). The time jump gets propagated to CPU0 via
sched_remote_clock() and stays stale on both cores for ~4 seconds.
There are only two other possibilities, which could cause a stale
sched clock:
1) ktime_get() which reads out CLOCK_MONOTONIC returns a sporadic
wrong value.
2) sched_clock() which reads the TSC returns a sporadic wrong value.
#1 can be excluded because sched_clock would continue to increase for
one jiffy and then go stale.
#2 can be excluded because it would not make the clock jump
forward. It would just result in a stale sched_clock for one jiffy.
After quite some brain twisting and finding the same pattern on other
traces, sched_clock_remote() remained the only place which could cause
such a problem and as explained above it's indeed racy on 32bit
systems.
So while on 64bit systems the readout is atomic, we need to verify the
remote readout on 32bit machines. We need to protect the local->clock
readout in sched_clock_remote() on 32bit as well because an NMI could
hit between the low and the high readout, call sched_clock_local() and
modify local->clock.
Thanks to Siegfried Wulsch for bearing with my debug requests and
going through the tedious tasks of running a bunch of reproducer
systems to generate the debug information which let me decode the
issue.
Reported-by: Siegfried Wulsch <Siegfried.Wulsch@rovema.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1304051544160.21884@ionos Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As ftrace_filter_lseek is now used with ftrace_pid_fops, it needs to
be moved out of the #ifdef CONFIG_DYNAMIC_FTRACE section as the
ftrace_pid_fops is defined when DYNAMIC_FTRACE is not.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently set_ftrace_pid and set_graph_function files use seq_lseek
for their fops. However seq_open() is called only for FMODE_READ in
the fops->open() so that if an user tries to seek one of those file
when she open it for writing, it sees NULL seq_file and then panic.
It can be easily reproduced with following command:
$ cd /sys/kernel/debug/tracing
$ echo 1234 | sudo tee -a set_ftrace_pid
In this example, GNU coreutils' tee opens the file with fopen(, "a")
and then the fopen() internally calls lseek().
Link: http://lkml.kernel.org/r/1365663302-2170-1-git-send-email-namhyung@kernel.org Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: stable@vger.kernel.org Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingo guesses this got introduced by commit 611ae8e3f520 ("x86/tlb:
enable tlb flush range support for x86") since that code started to free
unused pagetables.
On x86-32 PAE kernels, that new code has the potential to free an entire
PMD page and will clear one of the four page-directory-pointer-table
(aka pgd_t entries).
The hardware aggressively "caches" these top-level entries and invlpg
does not actually affect the CPU's copy. If we clear one we *HAVE* to
do a full TLB flush, otherwise we might continue using a freed pmd page.
(note, we do this properly on the population side in pud_populate()).
This patch tracks whenever we clear one of these entries in the 'struct
mmu_gather', and ensures that we follow up with a full tlb flush.
BTW, I disassembled and checked that:
if (tlb->fullmm == 0)
and
if (!tlb->fullmm && !tlb->need_flush_all)
generate essentially the same code, so there should be zero impact there
to the !PAE case.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Artem S Tashkinov <t.artem@mailcity.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If index++ calculates from 0, the checking condition of "while
(index++)" fails & it doesn't check any more. It doesn't follow
the loop that used at here.
Replace it by endless loop at here. Then it keeps parsing
"gpio-ranges" property until it ends.
Anatol Pomozov identified a race condition that hits module unloading
and re-loading. To quote Anatol:
"This is a race codition that exists between kset_find_obj() and
kobject_put(). kset_find_obj() might return kobject that has refcount
equal to 0 if this kobject is freeing by kobject_put() in other
thread.
Here is timeline for the crash in case if kset_find_obj() searches for
an object tht nobody holds and other thread is doing kobject_put() on
the same kobject:
THREAD A (calls kset_find_obj()) THREAD B (calls kobject_put())
splin_lock()
atomic_dec_return(kobj->kref), counter gets zero here
... starts kobject cleanup ....
spin_lock() // WAIT thread A in kobj_kset_leave()
iterate over kset->list
atomic_inc(kobj->kref) (counter becomes 1)
spin_unlock()
spin_lock() // taken
// it does not know that thread A increased counter so it
remove obj from list
spin_unlock()
vfree(module) // frees module object with containing kobj
// kobj points to freed memory area!!
kobject_put(kobj) // OOPS!!!!
The race above happens because module.c tries to use kset_find_obj()
when somebody unloads module. The module.c code was introduced in
commit 6494a93d55fa"
Anatol supplied a patch specific for module.c that worked around the
problem by simply not using kset_find_obj() at all, but rather than make
a local band-aid, this just fixes kset_find_obj() to be thread-safe
using the proper model of refusing the get a new reference if the
refcount has already dropped to zero.
See examples of this proper refcount handling not only in the kref
documentation, but in various other equivalent uses of this pattern by
grepping for atomic_inc_not_zero().
[ Side note: the module race does indicate that module loading and
unloading is not properly serialized wrt sysfs information using the
module mutex. That may require further thought, but this is the
correct fix at the kobject layer regardless. ]
Revert commit 62a3ddef6181 ("vfs: fix spinning prevention in prune_icache_sb").
This commit doesn't look right: since we are looking at the tail of the
list (sb->s_inode_lru.prev) if we want to skip an inode, we should put
it back at the head of the list instead of the tail, otherwise we will
keep spinning on it.
Discovered when investigating why prune_icache_sb came top in perf
reports of a swapping load.
This patch fixes a bug where a handful of informational / control CDBs
that should be allowed during ALUA access state Standby/Offline/Transition
where incorrectly returning CHECK_CONDITION + ASCQ_04H_ALUA_TG_PT_*.
This includes INQUIRY + REPORT_LUNS, which would end up preventing LUN
registration when LUN scanning occured during these ALUA access states.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a result of the SMP discover function is PHY VACANT,
the content of discover response structure (dr) is not valid.
It sometimes happens that dr->attached_sas_addr can contain
even SAS address of other phy. In such case an invalid phy
is created, what causes NULL pointer dereference during
destruction of expander's phys.
So if a result of SMP function is PHY VACANT, the content of discover
response structure (dr) must not be copied to phy structure.
When withdraw occurs, we need to continue to allow unlocks of fcntl
locks to occur, however these will only be local, since the node has
withdrawn from the cluster. This prevents triggering a VFS level
bug trap due to locks remaining when a file is closed.
Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found. This
garantees that msg is either a error pointer or a copy address.
Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Reported-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As commit 40dc166c (PM / Core: Introduce struct syscore_ops for core
subsystems PM) say, syscore_ops operations should be carried with one
CPU on-line and interrupts disabled. However, after commit f96972f2d
(kernel/sys.c: call disable_nonboot_cpus() in kernel_restart()),
syscore_shutdown() is called before disable_nonboot_cpus(), so break
the rules. We have a MIPS machine with a 8259A PIC, and there is an
external timer (HPET) linked at 8259A. Since 8259A has been shutdown
too early (by syscore_shutdown()), disable_nonboot_cpus() runs without
timer interrupt, so it hangs and reboot fails. This patch call
syscore_shutdown() a little later (after disable_nonboot_cpus()) to
avoid reboot failure, this is the same way as poweroff does.
For consistency, add disable_nonboot_cpus() to kernel_halt().
Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cyclic DMA is only used by audio which needs DMA to be started without a
delay.
If the DMA for audio is started using the tasklet we experience random
channel switch (to be more precise: channel shift).
Reported-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The admux clock seems to be the audmux clock as tests show. audmux does
not work without this clock enabled. Currently imx35 does not register a
clock device for audmux. This patch adds this registration. imx-audmux
driver already handles a clock device, so no changes are necessary
there.
In the conversion to pinctrl, an error in the pins for the rebuild
LED was introduced. This patch assigns the correct pins and includes
the correct name for the LED in kirkwood-iomega_ix2_200.dts.
Signed-off-by: Nigel Roberts <nigel@nobiscuit.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Charge Pump needs the DSP clock to work properly, without it the
bypass to HP/LINEOUT is not working properly. This requirement is not
mentioned in the datasheet but has been confirmed by Mark Brown from
Wolfson.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg() function expects __u16 types and performs
the endianness conversions by itself.
However, in three places, a conversion is performed before it is
handed over to usb_control_msg(), which leads to a double conversion
(= no conversion):
* snd_usb_nativeinstruments_boot_quirk()
* snd_nativeinstruments_control_get()
* snd_nativeinstruments_control_put()
Caught by sparse:
sound/usb/mixer_quirks.c:512:38: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:512:38: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:512:38: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:35: warning: incorrect type in argument 5 (different base types)
sound/usb/mixer_quirks.c:543:35: expected unsigned short [unsigned] [usertype] value
sound/usb/mixer_quirks.c:543:35: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:56: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:543:56: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:543:56: got restricted __le16 [usertype] <noident>
sound/usb/quirks.c:502:35: warning: incorrect type in argument 5 (different base types)
sound/usb/quirks.c:502:35: expected unsigned short [unsigned] [usertype] value
sound/usb/quirks.c:502:35: got restricted __le16 [usertype] <noident>
Checking for disabled resources board breaks detection pnp on another
board "AMI UEFI implementation (Version: 0406 Release Date: 06/06/2012)".
I'm working with the reporter of the original bug to write and test
a better fix.
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: users@rt2x00.serialmonkey.com Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log