Matt Redfearn [Tue, 20 Sep 2016 08:47:25 +0000 (09:47 +0100)]
MIPS: tlb-r4k: If there are wired entries, don't use TLBINVF
When adding a wired entry to the TLB via add_wired_entry, the tlb is
flushed with local_flush_tlb_all, which on CPUs with TLBINV results in
the new wired entry being flushed again.
Behavior of the TLBINV instruction applies to all applicable TLB entries
and is unaffected by the setting of the Wired register. Therefore if
the TLB has any wired entries, fall back to iterating over the entries
rather than blasting them all using TLBINVF.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Ohad Ben-Cohen <ohad@wizery.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: lisa.parratt@imgtec.com Cc: Hugh Dickins <hughd@google.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: David S. Miller <davem@davemloft.net> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: linux-remoteproc@vger.kernel.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14283/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 1 Sep 2016 16:30:15 +0000 (17:30 +0100)]
MIPS: c-r4k: Fix flush_icache_range() for EVA
flush_icache_range() flushes icache lines in a protected fashion for
kernel addresses, however this isn't correct with EVA where protected
cache ops only operate on user addresses, making flush_icache_range()
ineffective.
Split the implementations of __flush_icache_user_range() from
flush_icache_range(), changing the normal flush_icache_range() to use
unprotected normal cache ops.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14156/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 1 Sep 2016 16:30:14 +0000 (17:30 +0100)]
MIPS: KVM: Use __local_flush_icache_user_range()
Convert KVM dynamic translation of guest instructions to flush icache
for guest mapped addresses using the new
__local_flush_icache_user_range() API to allow the more generic
flush_icache_range() to be changed to work on kernel addresses only.
James Hogan [Thu, 1 Sep 2016 16:30:13 +0000 (17:30 +0100)]
MIPS: uprobes: Flush icache via kernel address
Update arch_uprobe_copy_ixol() to use the kmap_atomic() based kernel
address to flush the icache with flush_icache_range(), rather than the
user mapping. We have the kernel mapping available anyway and this
avoids having to switch to using the new __flush_icache_user_range() for
the sake of Enhanced Virtual Addressing (EVA) where flush_icache_range()
will become ineffective on user addresses.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14154/
Patchwork: https://patchwork.linux-mips.org/patch/14308/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 1 Sep 2016 16:30:12 +0000 (17:30 +0100)]
MIPS: cacheflush: Use __flush_icache_user_range()
The cacheflush(2) system call uses flush_icache_range() to flush a range
of usermode addresses from the icache, so change it to utilise the new
__flush_icache_user_range() API to allow the more generic
flush_icache_range() to be changed to work on kernel addresses only.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14153/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
flush_icache_range() is used for both user addresses (i.e.
cacheflush(2)), and kernel addresses (as the API documentation
describes).
This isn't really suitable however for Enhanced Virtual Addressing (EVA)
where cache operations on usermode addresses must use a different
instruction, and the protected cache ops assume user addresses, making
flush_icache_range() ineffective on kernel addresses.
Split out a new __flush_icache_user_range() and
__local_flush_icache_user_range() for users which actually want to flush
usermode addresses (note that flush_icache_user_range() already exists
on various architectures but with different arguments).
The implementation of flush_icache_range() will be changed in an
upcoming commit to use unprotected normal cache ops so as to always work
on the kernel mode address space.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14152/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 1 Sep 2016 16:30:10 +0000 (17:30 +0100)]
MIPS: c-r4k: Drop bc_wback_inv() from icache flush
The EVA conditional bc_wback_inv() at the end of flush_icache_range() to
flush the modified code all the way back to RAM was apparently there for
debug purposes and to accommodate the Malta EVA configuration which
makes use of a physical alias, and didn't use the CP0_EBase.WG (Write
Gate) bit to put the exception vector in the same physical alias where
the exception vector code is written and is being flushed.
Now that CP0_EBase.WG is used, lets drop this flush.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14151/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Thu, 1 Sep 2016 16:30:09 +0000 (17:30 +0100)]
MIPS: traps: Ensure full EBase is written
On CPUs which support the EBase WG (write gate) flag, the most
significant bits of the exception base can be changed. Firmware running
on a VP(E) using MIPS rproc may change EBase to point into the user
segment where the firmware is located such that it can service
interrupts. When control is transferred back to the kernel the EBase
must be switched back into the kernel segment, such that the kernel's
exception vectors are used.
Similarly when vectored interrupts (vint) or vectored external interrupt
controllers (veic) are enabled an exception vector is allocated from
bootmem, and written to the EBase register. Due to the WG flag being
clear, only bits 29:12 will be written. Asside from the rproc case above
this is normally fine (as it will usually be a low allocation within the
KSeg0 range, however when Enhanced Virtual Addressing (EVA) is enabled
the allocation may be outside of the traditional KSeg0/KSeg1 address
range, resulting in the wrong EBase being written.
Correct both cases (configure_exception_vector() for the boot CPU, and
per_cpu_trap_init() for secondary CPUs) to write EBase with the WG flag
first if supported.
On the Malta EVA configuration, KSeg0 is mapped to physical address 0,
and memory is allocated from the KUSeg segment which is mapped to
physical address 0x80000000, which physically aliases the RAM at 0. This
only worked due to the exception base address aliasing the same
underlying RAM that was written to & cache flushed, and due to
flush_icache_range() going beyond the call of duty and flushing from the
L2 cache too (due to the differing physical addresses).
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14150/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 1 Sep 2016 16:30:08 +0000 (17:30 +0100)]
MIPS: traps: Convert ebase to KSEG0
When allocating boot memory for the exception vector when vectored
interrupts (vint) or vectored external interrupt controllers (veic) are
enabled, try to ensure that the virtual address resides in KSeg0 (and
WARN should that not be possible).
This will be helpful on MIPS64 cores supporting the CP0_EBase Write Gate
(WG) bit once we start using the WG bit to write the full ebase into
CP0_EBase, as we ideally need to avoid hitting the architecturally
poorly defined exception base for Cache Errors when CP0_EBase is in
XKPhys.
An exception is made for Enhanced Virtual Addressing (EVA) kernels which
allow segments to be rearranged and to become uncached during cache
error handling, making it valid for ebase to be elsewhere.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14149/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Thu, 1 Sep 2016 16:30:07 +0000 (17:30 +0100)]
MIPS: traps: 64bit kernels should read CP0_EBase 64bit
When reading the CP0_EBase register containing the WG (write gate) bit,
the ebase variable should be set to the full value of the register, i.e.
on a 64-bit kernel the full 64-bit width of the register via
read_cp0_ebase_64(), and on a 32-bit kernel the full 32-bit width
including bits 31:30 which may be writeable.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14148/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:19 +0000 (10:45 +0100)]
MIPS: SMP: Wrap call to mips_cpc_lock_other in mips_cm_lock_other
All calls to mips_cpc_lock_other should be wrapped in
mips_cm_lock_other. This only matters if the system has CM3 and is using
cpu idle, since otherwise a) the CPC lock is sufficent for CM < 3 and b)
any systems with CM > 3 have not been able to use cpu idle until now.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: James Hogan <james.hogan@imgtec.com> Cc: Qais Yousef <qsyousef@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/14227/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:18 +0000 (10:45 +0100)]
MIPS: pm-cps: Support CM3 changes to Coherence Enable Register
MIPS CM3 changed the management of coherence. Instead of a coherence
control register with a bitmask of coherent domains, CM3 simply has a
coherence enable register with a single bit to enable coherence of the
local core. Support this by clearing and setting this single bit to
disable / enable coherence.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Tony Wu <tung7970@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Nikolay Martynov <mar.kolya@gmail.com> Cc: Kees Cook <keescook@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14226/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:16 +0000 (10:45 +0100)]
MIPS: pm-cps: Remove selection of sync types
Instead of selecting an implementation or vendor specific sync type for
the required sync operations, always use the architecturally mandated
sync types which previous patches have put in place. The selection of
special sync types is now redundant an can be removed.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Kees Cook <keescook@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14223/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:15 +0000 (10:45 +0100)]
MIPS: pm-cps: Use MIPS standard completion barrier
SYNC type 0 is defined in the MIPS architecture as a completion barrier
where all loads/stores in the pipeline before the sync instruction must
complete before any loads/stores subsequent to the sync instruction.
In places where we require loads / stores be globally completed, use the
standard completion sync stype.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14224/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:14 +0000 (10:45 +0100)]
MIPS: pm-cps: Use MIPS standard lightweight ordering barrier
Since R2 of the MIPS architecture, SYNC(0x10) has been an optional but
architecturally defined ordering barrier. If a CPU does not implement it,
the arch specifies that it must fall back to SYNC(0).
In places where we require that the instruction stream not be reordered,
but do not require that loads / stores are gloablly completed, use the
defined standard sync stype.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14221/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:13 +0000 (10:45 +0100)]
MIPS: Barrier: Add definitions of SYNC stype values
Add the definitions of sync stype 0 (global completion barrier) and sync
stype 0x10 (local ordering barrier) to barrier.h for use with the sync
instruction.
These types are defined by the MIPS Instruction Set since R2 of the
architecture and are documented in document MD00087 table 6.5.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14222/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:12 +0000 (10:45 +0100)]
MIPS: pm-cps: Update comments on barrier instructions
This code makes large use of barriers, which had quite vague
descriptions. Update the comments to make the choice of barrier and
reason for it more clear.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Kees Cook <keescook@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14220/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:11 +0000 (10:45 +0100)]
MIPS: pm-cps: Change FSB workaround to CPU blacklist
The check for whether a CPU required the FSB flush workaround
previously required every CPU not requiring it to be whitelisted. That
approach does not scale well as new CPUs are introduced so change the
default from a WARN and returning an error to just returning 0. Any CPUs
requiring the workaround can then be added to the blacklist.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14218/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 7 Sep 2016 09:45:10 +0000 (10:45 +0100)]
MIPS: CPC: Avoid lock when MIPS CM >= 3 is present
MIPS CM version 3 removed the CPC_CL_OTHER register and instead the
CM_CL_OTHER register is used to redirect the CPC_OTHER region. As such,
we should not write the unimplmented register and can avoid the
spinlock as well.
These lock functions should aleady be called within the context of a
mips_cm_{lock,unlock}_other pair ensuring the correct CPC_OTHER region
will be accessed.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14219/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aaro Koskinen [Fri, 2 Sep 2016 20:44:16 +0000 (23:44 +0300)]
MIPS: Octeon: Delete legacy hack for broken bootloaders
Delete legacy hack for broken bootloaders. The warning has been in kernel
for several years, and if there are still users using such bootloaders,
they can fix the boot by supplying a proper DTB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <ddaney@caviumnetworks.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14201/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Keith Busch [Tue, 13 Sep 2016 15:21:47 +0000 (09:21 -0600)]
MIPS: PCI: Reduce stack frame usage
This patch removes creating a fake pci device in MIPS early config
access and instead just uses the pci bus to get the same functionality.
The struct pci_dev is too large to allocate on the stack, and was relying
on compiler optimizations to remove its usage.
Replace the custom minimal clock implementation for Toshiba TXx9 by a
basic implementation using the Common Clock Framework.
The only clocks that are provided are those needed by TXx9-specific
drivers ("imbus" and "spi" (TX4938 only)), and their common parent
clock "gbus". Other clocks can be added when needed.
WATCHDOG: txx9wdt: Add missing clock (un)prepare calls for CCF
While the custom minimal TXx9 clock implementation doesn't need or use
clock (un)prepare calls (they are dummies if !CONFIG_HAVE_CLK_PREPARE),
they are mandatory when using the Common Clock Framework.
MIPS: TXx9: tx49xx: Move GPIO setup from .mem_setup() to .arch_init()
txx9_gpio_init() calls gpiochip_add_data(), which fails with -ENOMEM as
it is called too early in the boot process. This causes all subsequent
GPIO operations to fail silently (before commit 54d77198fdfbc4f0 ("gpio:
bail out silently on NULL descriptors") it printed the error message
"gpiod_direction_output_raw: invalid GPIO" on RBTX49[23]7).
Postpone all GPIO setup to .arch_init() time to fix this.
MIPS: TXx9: tx39xx: Move GPIO setup from .mem_setup() to .arch_init()
txx9_gpio_init() calls gpiochip_add_data(), which fails with -ENOMEM as
it is called too early in the boot process. This causes all subsequent
GPIO operations to fail silently.
Postpone all GPIO setup to .arch_init() time to fix this.
Paul Gortmaker [Mon, 15 Aug 2016 23:11:52 +0000 (19:11 -0400)]
MIPS: Migrate exception table users off module.h and onto extable.h
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
In the case of traps.c we can't dump the module.h include since it is
also used to provide "print_modules".
Paul Gortmaker [Mon, 15 Aug 2016 20:30:53 +0000 (16:30 -0400)]
MIPS: ralink: Make timer explicitly non-modular
The Makefile entry controlling compilation of this code is "obj-y"
meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: John Crispin <john@phrozen.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13931/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Wed, 10 Aug 2016 16:11:03 +0000 (17:11 +0100)]
MIPS: Delete unused file smp-gic.c
Commit 7eb8c99db26c ("MIPS: Delete smp-gic.c") removed the file from the
Makefile and the option to build it from KConfig, but left the file
itself floating in the tree.
Matt Redfearn [Thu, 4 Aug 2016 16:19:38 +0000 (17:19 +0100)]
MIPS: Move identification of VP(E) into proc.c from smp-mt.c
The addition of VPE information to /proc/cpuinfo used to be in smp-mt.c.
This file is not used by MIPS r6 kernels, so the Virtual Processor
information was not present for these CPU types.
Move the code to print VPE information into proc.c, add a case for MIPS
r6 CPUS, and remove the block from smp-mt.c.
Commit 380e4270 added support for bcm97435svmb.dtb but missed adding it to
DT_NONE.
Also refactor DT_NONE dtbs in order to add larger names in the future.
Paul Gortmaker [Wed, 3 Aug 2016 19:03:59 +0000 (15:03 -0400)]
MIPS: Don't specify STACKPROTECTOR in defconfigs
Only one defconfig has a STACKPROTECTOR value. And it asks for
the strong variant, which isn't supported by older toolchains.
Due to the nature of MIPS having more platform specific code than say
x86, the allyesconfig and allmodconfig aren't as effective for build
coverage. So, in addition, I like to use a trivial script to walk all
the defconfigs and build each one.
However I will get false positives on unsupported stackprotector values
with an older toolchain like gcc-4.6.3. As in this instance I am just
using the compiler as a glorified syntax checker on a machine where I
build a bunch of other arch for the same reason, there is no real
motivation to get a newer toolchain for improved optimization etc.
Since there is only one of them, and there is nothing about these
settings that are board/platform specific, I propose we just eliminate
the existing instance and take the default.
Linus Torvalds [Sun, 2 Oct 2016 22:23:00 +0000 (15:23 -0700)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three relatively small fixes for ARM:
- Roger noticed that dma_max_pfn() was calculating the upper limit
wrongly, by adding the PFN offset of memory twice.
- A fix from Robin to correct parsing of MPIDR values when the
address size is larger than one BE32 unit.
- A fix from Srinivas to ensure that we do not rely on the boot
loader (or previous Linux kernel) setting the translation table
base register a certain way in the decompressor, which can lead to
crashes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
ARM: 8617/1: dma: fix dma_max_pfn()
ARM: 8616/1: dt: Respect property size when parsing CPUs
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894d3a ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894d3 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores") Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Srinivas Ramana <sramana@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sun, 2 Oct 2016 18:04:29 +0000 (11:04 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"The last regression fixes for 4.8 final:
- Two patches addressing the fallout of the CR4 optimizations which
caused CR4-less machines to fail.
- Fix the VDSO build on big endian machines
- Take care of FPU initialization if no CPUID is available otherwise
task struct size ends up being zero
- Fix up context tracking in case load_gs_index fails"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
x86/init: Fix cr4_init_shadow() on CR4-less machines
1) Fix wrong TCP checksums on MTU probing when checksum offloading is
disabled, from Douglas Caetano dos Santos.
2) Fix qdisc backlog updates in qfq and sfb schedulers, from Cong Wang.
3) Route lookup flow key protocol value is wrong in ip6gre_xmit_other(),
fix from Lance Richardson.
4) Scheduling while atomic in multicast routing code of ipv4 and ipv6,
fix from Nikolay Aleksandrov.
5) Fix packet alignment in fec driver, from Eric Nelson.
6) Fix perf regression in sctp due to struct layout and cache misses,
from Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
act_ife: Fix false encoding
act_ife: Fix external mac header on encode
VSOCK: Don't dec ack backlog twice for rejected connections
Revert "net: ethernet: bcmgenet: use phydev from struct net_device"
net: fec: align IP header in hardware
net: fec: remove QUIRK_HAS_RACC from i.mx27
net: fec: remove QUIRK_HAS_RACC from i.mx25
ipmr, ip6mr: fix scheduling while atomic and a deadlock with ipmr_get_route
ip6_gre: fix flowi6_proto value in ip6gre_xmit_other()
tcp: fix a compile error in DBGUNDO()
tcp: fix wrong checksum calculation on MTU probing
sch_sfb: keep backlog updated with qlen
sch_qfq: keep backlog updated with qlen
can: dev: fix deadlock reported after bus-off
Paul Burton [Fri, 30 Sep 2016 16:25:01 +0000 (17:25 +0100)]
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
When discovering the number of VPEs per core, smp_num_siblings will be
incorrect for kernels built without support for the MIPS MultiThreading
(MT) ASE running on systems which implement said ASE. This leads to
accesses to VPEs in secondary cores being performed incorrectly since
mips_cm_vp_id calculates the wrong ID to write to the local "other"
registers. Fix this by examining the number of VPEs in the core as
reported by the CM.
This patch presumes that the number of VPEs will be the same in each
core of the system. As this path only applies to systems with CM version
2.5 or lower, and this property is true of all such known systems, this
is likely to be fine but is described in a comment for good measure.
Linus Torvalds [Sat, 1 Oct 2016 14:37:15 +0000 (07:37 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One final fix before 4.8.
There was a memory leak triggered by turning scsi mq off due to the
fact that we assume on host release that the already running hosts
weren't mq based because that's the state of the global flag (even
though they were).
Fix it by tracking this on a per host host basis"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Avoid that toggling use_blk_mq triggers a memory leak
Linus Torvalds [Sat, 1 Oct 2016 04:25:09 +0000 (21:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"One small change to make joydev (which is used by older games) to bind
to devices that export Z axis but not X or Y (such as TRC rudder)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - recognize devices with Z axis as joysticks
Merge more fixes from Andrew Morton:
"Three fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
John Youn [Fri, 30 Sep 2016 22:11:35 +0000 (15:11 -0700)]
include/linux/property.h: fix typo/compile error
This fixes commit d76eebfa175e ("include/linux/property.h: fix build
issues with gcc-4.4.4").
With that commit we get the following compile error when using the
PROPERTY_ENTRY_INTEGER_ARRAY macro.
include/linux/property.h:201:39: error: `u32_data' undeclared (first
use in this function)
PROPERTY_ENTRY_INTEGER_ARRAY(_name_, u32, _val_)
^
include/linux/property.h:193:17: note: in definition of macro
`PROPERTY_ENTRY_INTEGER_ARRAY'
{ .pointer = { _type_##_data = _val_ } }, \
^
This needs a '.' to reference the union member. It seems this was just
overlooked here since it is done correctly in similar constructs in
other parts of the original commit.
This fix is in preparation of upcoming commits that will use this macro.
Fixes: commit d76eebfa175e ("include/linux/property.h: fix build issues with gcc-4.4.4") Link: http://lkml.kernel.org/r/2de3b929290d88a723ed829a3e3cbd02044714df.1475114627.git.johnyoun@synopsys.com Signed-off-by: John Youn <johnyoun@synopsys.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Ren [Fri, 30 Sep 2016 22:11:32 +0000 (15:11 -0700)]
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
The testcase "mmaptruncate" of ocfs2-test deadlocks occasionally.
In this testcase, we create a 2*CLUSTER_SIZE file and mmap() on it;
there are 2 process repeatedly performing the following operations
respectively: one is doing memset(mmaped_addr + 2*CLUSTER_SIZE - 1, 'a',
1), while the another is playing ftruncate(fd, 2*CLUSTER_SIZE) and then
ftruncate(fd, CLUSTER_SIZE) again and again.
In ocfs2_write_begin_nolock(), we first grab the pages and then allocate
disk space for this write; ocfs2_try_to_free_truncate_log() will be
called if -ENOSPC is returned; if we're lucky to get enough clusters,
which is usually the case, we start over again.
But in ocfs2_free_write_ctxt() the target page isn't unlocked, so we
will deadlock when trying to grab the target page again.
Also, -ENOMEM might be returned in ocfs2_grab_pages_for_write().
Another deadlock will happen in __do_page_mkwrite() if
ocfs2_page_mkwrite() returns non-VM_FAULT_LOCKED, and along with a
locked target page.
These two errors fail on the same path, so fix them by unlocking the
target page manually before ocfs2_free_write_ctxt().
Jan Kara helps me clear out the JBD2 part, and suggest the hint for root
cause.
Changes since v1:
1. Also put ENOMEM error case into consideration.
Link: http://lkml.kernel.org/r/1474173902-32075-1-git-send-email-zren@suse.com Signed-off-by: Eric Ren <zren@suse.com> Reviewed-by: He Gang <ghe@suse.com> Acked-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 30 Sep 2016 22:11:29 +0000 (15:11 -0700)]
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
Antonio reports the following crash when using fuse under memory pressure:
kernel BUG at /build/linux-a2WvEb/linux-4.4.0/mm/workingset.c:346!
invalid opcode: 0000 [#1] SMP
Modules linked in: all of them
CPU: 2 PID: 63 Comm: kswapd0 Not tainted 4.4.0-36-generic #55-Ubuntu
Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 3904 04/27/2013
task: ffff88040cae6040 ti: ffff880407488000 task.ti: ffff880407488000
RIP: shadow_lru_isolate+0x181/0x190
Call Trace:
__list_lru_walk_one.isra.3+0x8f/0x130
list_lru_walk_one+0x23/0x30
scan_shadow_nodes+0x34/0x50
shrink_slab.part.40+0x1ed/0x3d0
shrink_zone+0x2ca/0x2e0
kswapd+0x51e/0x990
kthread+0xd8/0xf0
ret_from_fork+0x3f/0x70
which corresponds to the following sanity check in the shadow node
tracking:
BUG_ON(node->count & RADIX_TREE_COUNT_MASK);
The workingset code tracks radix tree nodes that exclusively contain
shadow entries of evicted pages in them, and this (somewhat obscure)
line checks whether there are real pages left that would interfere with
reclaim of the radix tree node under memory pressure.
While discussing ways how fuse might sneak pages into the radix tree
past the workingset code, Miklos pointed to replace_page_cache_page(),
and indeed there is a problem there: it properly accounts for the old
page being removed - __delete_from_page_cache() does that - but then
does a raw raw radix_tree_insert(), not accounting for the replacement
page. Eventually the page count bits in node->count underflow while
leaving the node incorrectly linked to the shadow node LRU.
To address this, make sure replace_page_cache_page() uses the tracked
page insertion code, page_cache_tree_insert(). This fixes the page
accounting and makes sure page-containing nodes are properly unlinked
from the shadow node LRU again.
Also, make the sanity checks a bit less obscure by using the helpers for
checking the number of pages and shadows in a radix tree node.
Fixes: 449dd6984d0e ("mm: keep page cache radix tree nodes in check") Link: http://lkml.kernel.org/r/20160919155822.29498-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Antonio SJ Musumeci <trapexit@spawn.link> Debugged-by: Miklos Szeredi <miklos@szeredi.hu> Cc: <stable@vger.kernel.org> [3.15+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... can be reproduced by running the GS testcase of the ldt_gdt test unit in
the x86 selftests.
do_int80_syscall_32() will call enter_form_user_mode() to convert context
tracking state from user state to kernel state. The load_gs_index() call
can fail with user gsbase, gsbase will be fixed up and proceed if this
happen.
However, enter_from_user_mode() will be called again in the fixed up path
though it is context tracking kernel state currently.
This patch fixes it by just fixing up gsbase and telling lockdep that IRQs
are off once load_gs_index() failed with user gsbase.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1475197266-3440-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixes: 57f90c3dfc75 ("x86/vdso: Error out if the vDSO isn't a valid DSO") Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: linux-next@vger.kernel.org Link: http://lkml.kernel.org/r/20160929193442.GA16617@gate.crashing.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andy Lutomirski [Thu, 29 Sep 2016 19:48:11 +0000 (12:48 -0700)]
x86/boot: Fix another __read_cr4() case on 486
The condition for reading CR4 was wrong: there are some CPUs with
CPUID but not CR4. Rather than trying to make the condition exact,
use __read_cr4_safe().
Fixes: 18bc7bd523e0 ("x86/boot: Synchronize trampoline_cr4_features and mmu_cr4_features directly") Reported-by: david@saggiorato.net Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Link: http://lkml.kernel.org/r/8c453a61c4f44ab6ff43c29780ba04835234d2e5.1475178369.git.luto@kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xin Long [Wed, 28 Sep 2016 18:55:44 +0000 (02:55 +0800)]
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
When sctp dumps all the ep->assocs, it needs to lock_sock first,
but now it locks sock in rcu_read_lock, and lock_sock may sleep,
which would break rcu_read_lock.
This patch is to get and hold one sock when traversing the list.
After that and get out of rcu_read_lock, lock and dump it. Then
it will traverse the list again to get the next one until all
sctp socks are dumped.
For sctp_diag_dump_one, it fixes this issue by holding asoc and
moving cb() out of rcu_read_lock in sctp_transport_lookup_process.
Fixes: 8f840e47f190 ("sctp: add the sctp_diag.c file") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 28 Sep 2016 18:37:28 +0000 (02:37 +0800)]
sctp: change to check peer prsctp_capable when using prsctp polices
Now before using prsctp polices, sctp uses asoc->prsctp_enable to
check if prsctp is enabled. However asoc->prsctp_enable is set only
means local host support prsctp, sctp should not abandon packet if
peer host doesn't enable prsctp.
So this patch is to use asoc->peer.prsctp_capable to check if prsctp
is enabled on both side, instead of asoc->prsctp_enable, as asoc's
peer.prsctp_capable is set only when local and peer both enable prsctp.
Fixes: a6c2f792873a ("sctp: implement prsctp TTL policy") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 28 Sep 2016 18:37:27 +0000 (02:37 +0800)]
sctp: remove prsctp_param from sctp_chunk
Now sctp uses chunk->prsctp_param to save the prsctp param for all the
prsctp polices, we didn't need to introduce prsctp_param to sctp_chunk.
We can just use chunk->sinfo.sinfo_timetolive for RTX and BUF polices,
and reuse msg->expires_at for TTL policy, as the prsctp polices and old
expires policy are mutual exclusive.
This patch is to remove prsctp_param from sctp_chunk, and reuse msg's
expires_at for TTL and chunk's sinfo.sinfo_timetolive for RTX and BUF
polices.
Note that sctp can't use chunk's sinfo.sinfo_timetolive for TTL policy,
as it needs a u64 variables to save the expires_at time.
This one also fixes the "netperf-Throughput_Mbps -37.2% regression"
issue.
Fixes: a6c2f792873a ("sctp: implement prsctp TTL policy") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 28 Sep 2016 18:37:26 +0000 (02:37 +0800)]
sctp: move sent_count to the memory hole in sctp_chunk
Now pahole sctp_chunk, it has 2 memory holes:
struct sctp_chunk {
struct list_head list;
atomic_t refcnt;
/* XXX 4 bytes hole, try to pack */
...
long unsigned int prsctp_param;
int sent_count;
/* XXX 4 bytes hole, try to pack */
This patch is to move up sent_count to fill the 1st one and eliminate
the 2nd one.
It's not just another struct compaction, it also fixes the "netperf-
Throughput_Mbps -37.2% regression" issue when overloading the CPU.
Fixes: a6c2f792873a ("sctp: implement prsctp TTL policy") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Milton Miller [Thu, 29 Sep 2016 16:24:08 +0000 (13:24 -0300)]
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.
The following trace is seen when the error is triggered:
This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].
Fixes: 0486a063b1ff ("tg3: prevent ifup/ifdown during PCI error recovery") Fixes: dfc8f370316b ("net/tg3: Release IRQs on permanent error") Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'drm-fixes-for-v4.8-final' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"drm fixes for final 4.8.
One big regression fix for udl, along with two amdgpu fixes and two
nouveau fixes.
All seems pretty safe and useful"
* tag 'drm-fixes-for-v4.8-final' of git://people.freedesktop.org/~airlied/linux:
drm/udl: fix line iterator in damage handling
drm/radeon/si/dpm: add workaround for for Jet parts
drm/amdgpu: disable CRTCs before teardown
drm/nouveau: Revert "bus: remove cpu_coherent flag"
drm/nouveau/fifo/nv04: avoid ramht race against cookie insertion
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Four fixes for "flush hint" support.
Flush hints are addresses advertised by the ACPI 6+ NFIT (NVDIMM
Firmware Interface Table) that when written and fenced guarantee that
writes pending in platform write buffers (outside the cpu) have been
flushed to media. They might also be used by hypervisors as a
trigger condition to flush guest-persistent memory ranges to storage.
Fix a potential data corruption issue, a broken definition of the
hint array, a wrong allocation size for the unit test implementation
of the flush hint table, and missing NULL check in an error path.
The unit test, while it did not prevent these bugs from being
merged, at least triggered occasional crashes in advance of
production usages.
- Fix handling of ACPI DSM error status results. The DSM mechanism
allows communication with platform and memory device firmware. We
correctly parse known errors, but were silently ignoring others.
Fix it to consistently fail any command with a non-zero status return
that we otherwise do not interpret / handle.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, region: fix flush hint table thinko
nfit: fail DSMs that return non-zero status by default
libnvdimm: fix devm_nvdimm_memremap() error path
tools/testing/nvdimm: fix allocation range for mock flush hint tables
nvdimm: fix PHYS_PFN/PFN_PHYS mixup
Paul Burton [Fri, 2 Sep 2016 14:17:31 +0000 (15:17 +0100)]
MIPS: Fix detection of unsupported highmem with cache aliases
The paging_init() function contains code which detects that highmem is
in use but unsupported due to dcache aliasing. However this code was
ineffective because it was being run before the caches are probed,
meaning that cpu_has_dc_aliases would always evaluate to false (unless a
platform overrides it to a compile-time constant) and the detection of
the unsupported case is never triggered. The kernel would then go on to
attempt to use highmem & either hit coherency issues or trigger the
BUG_ON in flush_kernel_dcache_page().
Fix this by running paging_init() later than cpu_cache_init(), such that
the cpu_has_dc_aliases macro will evaluate correctly & the unsupported
highmem case will be detected successfully.
This then leads to a formerly hidden issue in that
mem_init_free_highmem() will attempt to free all highmem pages, even
though we're avoiding use of them & don't have valid page structs for
them. This leads to an invalid pointer dereference & a TLB exception.
Avoid this by skipping the loop in mem_init_free_highmem() if
cpu_has_dc_aliases evaluates true.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Rabin Vincent <rabinv@axis.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Jaedon Shin <jaedon.shin@gmail.com> Cc: Toshi Kani <toshi.kani@hpe.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14184/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Fri, 2 Sep 2016 15:07:10 +0000 (16:07 +0100)]
MIPS: Malta: Fix IOCU disable switch read for MIPS64
Malta boards used with CPU emulators feature a switch to disable use of
an IOCU. Software has to check this switch & ignore any present IOCU if
the switch is closed. The read used to do this was unsafe for 64 bit
kernels, as it simply casted the address 0xbf403000 to a pointer &
dereferenced it. Whilst in a 32 bit kernel this would access kseg1, in a
64 bit kernel this attempts to access xuseg & results in an address
error exception.
Fix by accessing a correctly formed ckseg1 address generated using the
CKSEG1ADDR macro.
Whilst modifying this code, define the name of the register and the bit
we care about within it, which indicates whether PCI DMA is routed to
the IOCU or straight to DRAM. The code previously checked that bit 0 was
also set, but the least significant 7 bits of the CONFIG_GEN0 register
contain the value of the MReqInfo signal provided to the IOCU OCP bus,
so singling out bit 0 makes little sense & that part of the check is
dropped.
Paul Burton [Fri, 19 Aug 2016 17:15:40 +0000 (18:15 +0100)]
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
When the kernel is built for microMIPS, branches targets need to be
known to be microMIPS code in order to result in bit 0 of the PC being
set. The branch target in the BUILD_ROLLBACK_PROLOGUE macro was simply
the end of the macro, which may be pointing at padding rather than at
code. This results in recent enough GNU linkers complaining like so:
mips-img-linux-gnu-ld: arch/mips/built-in.o: .text+0x3e3c: Unsupported branch between ISA modes.
mips-img-linux-gnu-ld: final link failed: Bad value
Makefile:936: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
Fix this by changing the branch target to be the start of the
appropriate handler, skipping over any padding.
Paul Burton [Fri, 19 Aug 2016 17:18:28 +0000 (18:18 +0100)]
MIPS: clear execution hazard after changing FTLB enable
On current P-series cores from Imagination the FTLB can be enabled or
disabled via a bit in the Config6 register, and an execution hazard is
created by changing the value of bit. The ftlb_disable function already
cleared that hazard but that does no good for other callers. Clear the
hazard in the set_ftlb_enable function that creates it, and only for the
cores where it applies.
This has the effect of reverting c982c6d6c48b ("MIPS: cpu-probe: Remove
cp0 hazard barrier when enabling the FTLB") which was incorrect.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: c982c6d6c48b ("MIPS: cpu-probe: Remove cp0 hazard barrier when enabling the FTLB") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14023/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Fri, 19 Aug 2016 17:18:27 +0000 (18:18 +0100)]
MIPS: Configure FTLB after probing TLB sizes from config4
On some cores (proAptiv, P5600) we make use of the sizes of the TLBs
to determine the desired FTLB:VTLB write ratio. However set_ftlb_enable
& thus calculate_ftlb_probability is called before decode_config4. This
results in us calculating a probability based on zero sizes, and we end
up setting FTLBP=3 for a 3:1 FTLB:VTLB write ratio in all cases. This
will make abysmal use of the available FTLB resources in the affected
cores.
Fix this by configuring the FTLB probability after having decoded
config4. However we do need to have enabled the FTLB before that point
such that fields in config4 actually reflect that an FTLB is present. So
set_ftlb_enable is now called twice, with flags indicating that it
should configure the write probability only the second time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: cf0a8aa0226d ("MIPS: cpu-probe: Set the FTLB probability bit on supported cores") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14022/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Fri, 19 Aug 2016 17:18:26 +0000 (18:18 +0100)]
MIPS: Stop setting I6400 FTLBP
The FTLBP field in Config7 for the I6400 is intended as chicken bits for
debugging rather than as a field that software actually makes use of.
For best performance, FTLBP should be left at its default value of 0
with all TLB writes hitting the FTLB by default.
Additionally, since set_ftlb_enable is called from decode_configs before
decode_config4 which determines the size of the TLBs, this was
previously always setting FTLBP=3 for a 3:1 FTLB:VTLB write ratio which
makes abysmal use of the available FTLB resources.
This effectively reverts b0c4e1b79d8a ("MIPS: Set up FTLB probability
for I6400").
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: b0c4e1b79d8a ("MIPS: Set up FTLB probability for I6400") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14021/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: DEC: Avoid la pseudo-instruction in delay slots
When expanding the la or dla pseudo-instruction in a delay slot the GNU
assembler will complain should the pseudo-instruction expand to multiple
actual instructions, since only the first of them will be in the delay
slot leading to the pseudo-instruction being only partially executed if
the branch is taken. Use of PTR_LA in the dec int-handler.S leads to
such warnings:
arch/mips/dec/int-handler.S: Assembler messages:
arch/mips/dec/int-handler.S:149: Warning: macro instruction expanded into multiple instructions in a branch delay slot
arch/mips/dec/int-handler.S:198: Warning: macro instruction expanded into multiple instructions in a branch delay slot
Steven J. Hill [Fri, 26 Aug 2016 19:02:04 +0000 (14:02 -0500)]
MIPS: Octeon: mark GPIO controller node not populated after IRQ init.
We clear the OF_POPULATED flag for the GPIO controller node on Octeon
processors. Otherwise, none of the devices hanging on the GPIO lines
are probed. The 'gpio-leds' driver on OCTEON failed to probe in addition
to other devices on Cavium 71xx and 78xx development boards.
Fixes: 15cc2ed6dcf9 ("of/irq: Mark initialised interrupt controllers as populated") Signed-off-by: Steven J. Hill <steven.hill@cavium.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <david.daney@cavium.com> Cc: Rob Herring <robh@kernel.org> Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14091/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch_uprobe_pre_xol needs to emulate a branch if a branch instruction
has been replaced with a breakpoint, but in fact an uninitialised local
variable was passed to the emulator routine instead of the original
instruction
Generic kernel code implements a weak version of set_orig_insn that
moves cached 'insn' from arch_uprobe to the original code location when
the trap is removed.
MIPS variant used arch_uprobe->orig_inst which was never initialised
properly, so this code only inserted a nop instead of the original
instruction. With that change orig_inst can also be safely removed.
projects / linux-beck.git / log