Felix Fietkau [Sat, 10 Aug 2013 13:59:15 +0000 (15:59 +0200)]
ath9k: fix rx descriptor related race condition
Similar to a race condition that exists in the tx path, the hardware
might re-read the 'next' pointer of a descriptor of the last completed
frame. This only affects non-EDMA (pre-AR93xx) devices.
To deal with this race, defer clearing and re-linking a completed rx
descriptor until the next one has been processed.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Sat, 10 Aug 2013 10:27:29 +0000 (12:27 +0200)]
brcmfmac: use configurable sdio bus header length for tx packet
Host tx glomming require an extended hardware sdio bus header to store
information for dongle. Introduce a variable in struct brcmf_sdio to replace
macro SDPCM_HDRLEN
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Sat, 10 Aug 2013 10:27:24 +0000 (12:27 +0200)]
brcmfmac: ignore IF event if firmware indicates it
Not every IF event from the firmware needs to result in a
related interface, netdev or wdev, on the host. This is
indicated in the event message. Handle that flag and effectively
ignore the firmware event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Sat, 10 Aug 2013 10:27:23 +0000 (12:27 +0200)]
brcmfmac: no fws locking outside fws module.
FWS uses locking to protect its data while being called from
various entries. On bus_txdata the lock was kept resulting in
unnecessary long locking, but also creating possibility for
deadlock. This update changes the locking to release lock when
bus_txdata is called.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Sat, 10 Aug 2013 10:27:22 +0000 (12:27 +0200)]
brcmfmac: always use worker thread for tx data.
When fw signalling is disabled tx is sent immediately. Using
queues and worker thread allows usb to do synchronous autopm. This
patch makes fws use queues and worker thread even if signalling is
not supported by FW or not enabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Sat, 10 Aug 2013 10:27:21 +0000 (12:27 +0200)]
brcmfmac: add AMPDU reordering functionality
This feature moves the responsibility of collecting all MPDUs in an
AMPDU session in the correct order from the firmware to the host
driver. This reduces buffer requirement on the firmware side.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Sat, 10 Aug 2013 10:27:20 +0000 (12:27 +0200)]
brcmfmac: .txdata() bus callback should not call brcmf_txcomplete()
With firmware-signalling the packet handed to the bus specific driver
layer should not be discarded with brcmf_txcomplete() in the failure
path. Instead only an error is returned and the caller decides what
to do with the packet.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Sat, 10 Aug 2013 10:27:19 +0000 (12:27 +0200)]
brcmfmac: use irq safe spinlock in brcmf_sdbrcm_txdata()
Firmware-signalling needs transmit to firmware to be atomic and
uses a spinlock with irq disabled. Therefor, brcmf_sdbrcm_txdata()
should not use spin_unlock_bh() as it would enable the interrupts.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 15 Aug 2013 19:55:10 +0000 (15:55 -0400)]
Merge tag 'nfc-next-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC pull request for the 3.12 release.
With this one we have:
- A few pn533 improvements and minor fixes. Testing our pn533 driver
against Google's NCI stack triggered a few issues that we fixed now.
We also added Tx fragmentation support to this driver.
- More NFC secure element handling. We added a GET_SE netlink command
for getting all the discovered secure elements, and we defined 2
additional secure element netlink event (transaction and connectivity).
We also fixed a couple of typos and copy-paste bugs from the secure
element handling code.
- Firmware download support for the pn544 driver. This chipset can enter a
special mode where it's waiting for firmware blobs to replace the
already flashed one. We now support that mode."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Lapuyade [Fri, 19 Jul 2013 12:59:45 +0000 (14:59 +0200)]
NFC: pn544: i2c: Add firmware download implementation for pn544
The pn544 can enter a firmware update mode where firmware blobs can be
pushed through the i2c line and flashed on the target.
A special command allows to verify that blobs are correctly flashed and
this is what we do for every downloaded firmware blob.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Eric Lapuyade [Fri, 19 Jul 2013 12:58:39 +0000 (14:58 +0200)]
NFC: pn544: Add firmware operations hci ops
The firmware operation callback is passed by the physical layer to the
hci driver during probe. All the driver does is to store it and call it
when the fw_upload hci ops is invoked.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Eric Lapuyade [Fri, 19 Jul 2013 12:57:55 +0000 (14:57 +0200)]
NFC: netlink: Add result of firmware operation to completion event
Result is added as an NFC_ATTR_FIRMWARE_DOWNLOAD_STATUS attribute
containing the standard errno positive value of the completion result.
This event will be sent when the firmare download operation is done and
will contain the operation result.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Wed, 3 Jul 2013 13:14:17 +0000 (15:14 +0200)]
NFC: pn533: Add some polling entropy
By not always starting the polling loop from the same modulation, we
avoid entering infinite loops where devices exporting 2 targets (on 2
different modulations) get the same target activated over and over.
If this target is not readable (e.g. a wallet emulating a tag), we will
stay in an error loop for ever.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Wed, 3 Jul 2013 12:50:36 +0000 (14:50 +0200)]
NFC: pn533: Add delay between each poll frame
It seems that some pn533 firmwares go belly up when being asked to send
poll frames too frequently. Adding a 10ms delay between each of them
calm the chip down and prevent it from crashing.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Wed, 24 Jul 2013 16:10:50 +0000 (18:10 +0200)]
NFC: Add a GET_SE netlink API
In order to fetch the discovered secure elements from an NFC controller,
we need to send a netlink command that will dump the list of available
SEs from NFC.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Wed, 24 Jul 2013 12:49:22 +0000 (14:49 +0200)]
NFC: Fix SE discovery failure warning condition
This is a typo coming from the initial implementation. se_discover fails
when it returns something different than zero and we should only display
a warning in that case.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Olivier Guiter [Thu, 13 Jun 2013 13:43:29 +0000 (13:43 +0000)]
NFC: pn533: Store the correct frame size (normal vs ext)
The extended information frame are sent by PN533 to exchange frames
larger than 255 bytes. These extended frame are very close from the
standard ones except for the header size length. On each incoming
frame, we set the correct header length, and we do that only for the
standard pn533 chipsets as the acr122 does not seem to support extended
frames properly.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Olivier Guiter [Thu, 13 Jun 2013 13:43:27 +0000 (15:43 +0200)]
NFC: pn533: Add extended information frame decoding support
Extended Information frames are slightly different from standard frames
as they can (theorically) handle datas up tu 64kB. PN533 firmware only
supports packet data up to 265 (incl. TFI byte)
This kind of frame are used when the pn533 wants to exchange more than
255 bytes, and this patch handles the reception of such frames.
Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Mon, 1 Jul 2013 15:26:58 +0000 (17:26 +0200)]
NFC: pn533: Enable AUTO RFCA
The AUTO RFCA bit forbids the pn533 chipset to turn its radio on
whenever an external field is present.
Without this bit set, some devices seems to get over flood by the
pn533 rf field and thus become hardly detectable.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Wed, 26 Jun 2013 16:16:21 +0000 (18:16 +0200)]
NFC: pn533: Fix the pn533 polling loop
By turning the radio off after each failed polling try, we dramatically
improve the pn533 polling loop efficiency.
Without this fix, all Android phones running the broadcom NFC stack are
almost never detected.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Wed, 26 Jun 2013 15:53:09 +0000 (17:53 +0200)]
NFC: pn533: Fix hardware busy loop when establishing the LLCP link
By using the standard setting for the regular pn533 dongles, we no
longer wait for ever for an ATR_RES. Without this, a failing ATR_REQ
will put the hardware into a busy loop, constantly waiting for an
ATR_RES.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Tue, 25 Jun 2013 14:22:08 +0000 (16:22 +0200)]
NFC: Define secure element connectivity and transaction events
The SE_CONNECTIVITY event is for an SE to request connection to e.g. a
modem. The SE_TRANSACTION one is sent when an application running on a
specific SE wants to notify the host CPU about the end of a transaction.
Those events respectively map to the EVT_CONNECTIVITY and the
EVT_TRANSACTION HCI events.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thierry Escande [Mon, 24 Jun 2013 10:02:28 +0000 (12:02 +0200)]
NFC: Fix missing static declarations
This patch fixes 3 sparse warnings:
nfcsim.c:63:25: sparse: symbol 'wq' was not declared.
nfcsim.c:484:12: sparse: symbol 'nfcsim_init' was not declared.
nfcsim.c:525:13: sparse: symbol 'nfcsim_exit' was not declared.
Bing Zhao [Sat, 10 Aug 2013 04:09:06 +0000 (21:09 -0700)]
mwifiex: fix build error when CONFIG_PM is not set
config: make ARCH=m68k allmodconfig
All error/warnings:
drivers/net/wireless/mwifiex/cfg80211.c: In function
'mwifiex_fill_coalesce_rule_info':
>> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit
declaration of function 'mwifiex_is_pattern_supported'
[-Werror=implicit-function-declaration]
drivers/net/wireless/mwifiex/cfg80211.c: At top level:
drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning:
'mwifiex_cfg80211_set_coalesce' defined but not used
[-Wunused-function]
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LNA combining algorithm has to be run for cards
that support the required diversity features, make
sure that that correct conditions are met before
enabing this algorithm.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 6 Aug 2013 12:18:13 +0000 (14:18 +0200)]
ath9k: use software queueing for multicast traffic
Create a per-vif dummy node entry for keeping the multicast software
queues. This helps in setups with a lot of mulitcast traffic that could
otherwise potentially drown out unicast traffic to stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 6 Aug 2013 12:18:11 +0000 (14:18 +0200)]
ath9k: use software queues for un-aggregated data packets
This is a first step for improving fairness between legacy and 802.11n
traffic, and it should also improve reliability of resets and channel
changes by keeping the hardware queue depth very short.
When an aggregation session is torn down, all packets in the retry queue
will be removed from the BAW and freed.
For all subframes that have not been transmitted yet, the A-MPDU flag
will be cleared, and a sequence number allocated. This ensures that the
next A-MPDU session will get the correct initial sequence number.
This happens both on aggregation session start and stop.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 6 Aug 2013 12:18:09 +0000 (14:18 +0200)]
ath9k: fix clearing expired A-MPDU subframes in tx completion
When the tid aggregation state has been marked as inactive, free
completed tx packets immediately. When a new aggregation session has not
been initialized yet, the BAW checks do not recognize it as expired.
Might fix potential stalls in setting up a new aggregation session.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 6 Aug 2013 12:18:08 +0000 (14:18 +0200)]
ath9k: prepare queueing code for handling unaggregated traffic
- Allow ath_tx_get_tid_subframe to return non-AMPDU subframes.
- Reset the tid paused state on aggregation stop
- Initialize software queues even when HT is not supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 6 Aug 2013 12:18:07 +0000 (14:18 +0200)]
ath9k: fix block ack window tracking check
When a packet has been tracked as part of the BlockAck window and added
to the hardware queue, it can end up back in the TID queue again with
fi->retries still set to 0 (e.g. if the frame was filtered). Keep an
extra bit for the BAW tracking status to fix this corner case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 6 Aug 2013 12:18:06 +0000 (14:18 +0200)]
ath9k: simplify ath_tx_form_aggr
The check for ATH_AMPDU_SUBFRAME_DEFAULT is unnecessary, since it's set
to half the maximum BlockAck Window size, which is already the maximum
value that h_baw could possibly have. Also remove unnecessary variables.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 6 Aug 2013 09:13:19 +0000 (11:13 +0200)]
brcmfmac: use CFG80211_TESTMODE_CMD
This is essentially the same, but written shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue_pause_queue_nocheck()is used only in this file.
Fix the following sparse warning:
drivers/net/wireless/rt2x00/rt2x00queue.c:939:6: warning: symbol 'rt2x00queue_pause_queue_nocheck' was not declared. Should it be
static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coalesce filters are configured in firmware based on settings
received from cfg80211.
Packet type which is required by firmware is determined based on
provided patterns in a rule:
Unicast: if pattern '01' with offset 0 is found
Multicast: if pattern '33:33' or '01:00:5e' with offset 0 is found
Broadcast: if pattern 'ff:ff:ff:ff' with offset 0 is found
Some example coalesce configuration files:
1) Coalesce Rx data packets from 192.168.0.88
mac address of our device is 00:50:43:21:53:7A
Source IP address offset comes out as 52 after following
calculations:
32 bytes of HW 802.11 header + 8 bytes LLC +
12 bytes in IPV4 header till source IP address
Destination mac is at offset 6 in HW header.
ath6kl: Fix invalid pointer access on fuzz testing with AP mode
In our Fuz testing, reference client corrupts the dest mac to "00:00:00:00:00:00"
in the WPA2 handshake no 2. During driver init the sta_list entries mac
addresses are by default "00:00:00:00:00:00". Driver returns an invalid
pointer (conn) and the drver shall crash, if rxtids (aggr_conn)
skb queues are accessed, since they would not be initialized.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to cancel heart beat timer before
freeing wmi to avoid potential NULL pointer
dereference.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: add SoC power save option to PCI features map
Unify the PCI options location.
By default the SoC PS option is disabled to boost the
performance and due to poor stability on early HW revisions.
In future we can remove the module parameter and turn on/off
the PS for given hardware.
This change also makes the pci module parameter for SoC PS static.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
iwlwifi: mvm: use designated initialization for some arrays
rs_ht_to_legacy and ant_toggle_lookup are arrays that
represent some state-machine. initialize them explicitly
with designated initialization to make them more clear
and avoid errors.
Johannes Berg [Fri, 2 Aug 2013 08:51:22 +0000 (10:51 +0200)]
iwlwifi: remove transport suspend/resume indirection
There's no reason for the transport to call itself through
indirect function pointers, inline the (little) code there
is and remove the indirection completely.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 25 Jul 2013 20:36:27 +0000 (22:36 +0200)]
iwlwifi: mvm: small cleanups in quota management code
Use a C99 initializer to clear the command and move the lockdep
assertion before the restart check. Since this causes problems
with the BUILD_BUG_ON() with some compilers, change that a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi: mvm: remove traffic load monitoring in rs
The traffic load monitoring isn't used anymore to decide whether
a Tx aggregation on a specific TID should be started.
No point in collecting these statistics. Remove the relevant code.
Johannes Berg [Tue, 30 Jul 2013 18:10:46 +0000 (20:10 +0200)]
iwlwifi: pcie: fix resume when no opmode is present
If no opmode is present during suspend/resume (i.e. if
the iwldvm or iwlmvm isn't loaded) the driver crashes
during resume, trying to call the rfkill notification.
Avoid that, and also don't enable the rfkill interrupt
in this case (to avoid crashing trying to handle the
interrupt later.)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Matti Gottlieb [Tue, 30 Jul 2013 12:29:37 +0000 (15:29 +0300)]
iwlwifi: mvm: Add RX statistics debugfs entry
Add a debugfs entry for the RX statistics received from
the firmware.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During a HW reset, the diversity config is programmed
in the set_board_values() eeprom callback, there is no
need to do it again by calling ath_ant_comb_update().
Fixed antenna support is not fully handled for 1-stream
cards, it can be done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
WB225 based cards like CUS198 and CUS230 support
both fast antenna diversity and LNA combining. Add support
for this and also program the SWCOM register with the
correct "ant_ctrl_comm2g_switch_enable" value.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MC_GAIN_CTL/CCK_DETECT registers have to be programmed
with the correct configuration values if WLAN/BT RX diversity
is enabled. Add this and also take care of the BTCOEX mode
when fast diversity is enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
For single-chain WLAN+BT cards, the BT antenna can be used for
WLAN RX when the BT interface is disabled. Rename the modparam
"antenna_diversity" to "bt_ant_diversity" to clarify this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Fri, 2 Aug 2013 23:57:40 +0000 (19:57 -0400)]
cw1200: Fix spurious BUG_ON() trigger when starting AP mode.
There's an underlying race condition with the unjoin_work() call that is
sometimes triggered depending on scheduling order and the phase of the
moon. This doesn't fix the race condition, but it does remove the
ill-advised BUG_ON() call in an easily-recoverable situation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michal Kazior [Fri, 2 Aug 2013 07:15:47 +0000 (09:15 +0200)]
ath10k: fix device teardown
This fixes interrupt-related issue when no
interfaces were running thus the device was
considered powered down.
The power_down() function isn't really powering
down the device. It simply assumed it won't
interrupt. This wasn't true in some cases and
could lead to paging failures upon FW indication
interrupt (i.e. FW crash) because some structures
aren't allocated in that device state.
One reason for that was that ar_pci->started
wasn't reset. The other is interrupts should've
been masked when teardown starts.
The patch reorganized interrupt setup and makes
sure ar_pci->started is reset accordingly.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using rfkill switch can make firmware unstable, what cause various
Microcode errors and kernel warnings. Reseting firmware just after
rfkill off (radio on) helped with that.
If device was put into a sleep and system was restarted or module
reloaded, we have to wake device up before sending other commands.
Otherwise it will fail to start with Microcode error.
Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michal Kazior [Wed, 31 Jul 2013 08:55:14 +0000 (10:55 +0200)]
ath10k: zero arvif memory on add_interface()
The private memory area in vif provided by
mac80211 isn't guaranteed to be zeroed.
This patch should fix issues when switching
between STA and AP interface types.
The tim_bitmap could become polluted by STA bssid
field (since it's a union), wep_keys array
could also become polluted with invalid pointers
and probably much more.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
projects / linux-beck.git / log