]> git.karo-electronics.de Git - linux-beck.git/log
linux-beck.git
9 years agodrm/i915: Split write of pattern to DP reg from intel_dp_set_link_train
Ander Conselvan de Oliveira [Fri, 23 Oct 2015 10:01:45 +0000 (13:01 +0300)]
drm/i915: Split write of pattern to DP reg from intel_dp_set_link_train

Split the register write with the new link training pattern out of
intel_dp_set_link_train(), so that the i915 specific code is in a
separate function.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-3-git-send-email-ander.conselvan.de.oliveira@intel.com
9 years agodrm/i915: Don't pass *DP around to link training functions
Ander Conselvan de Oliveira [Fri, 23 Oct 2015 10:01:44 +0000 (13:01 +0300)]
drm/i915: Don't pass *DP around to link training functions

It just makes the code more confusing, so just reference intel_dp_>DP
directly.

Note that this also fix a bug where the value of intel_dp->DP could be
different than the last value written to the hw, due to an early return
that would skip the 'intel_dp->DP = DP' line.

v2: Don't preserve old DP value on failure. (Sivakumar)
  - Don't call drm_dp_clock_recovery_ok() twice. (Sivakumar)
  - Keep return type of clock recovery and channel equalization
    functions as void. (Ander)

v3: Remove DP parameter from intel_dp_set_signal_levels(). (Sivakumar)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-2-git-send-email-ander.conselvan.de.oliveira@intel.com
9 years agodrm/i915/kbl: Kabylake uses the same GMS values as Skylake
Deepak S [Thu, 29 Oct 2015 17:22:01 +0000 (10:22 -0700)]
drm/i915/kbl: Kabylake uses the same GMS values as Skylake

Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446139321-2818-2-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915/skl: While sanitizing cdclock check the SWF18 as well
Shobhit Kumar [Thu, 5 Nov 2015 12:35:32 +0000 (18:05 +0530)]
drm/i915/skl: While sanitizing cdclock check the SWF18 as well

SWF18 is set if the display has been initialized by the pre-os. It also
gives what configuration is enabled on which pipe. In skl_sanitize_cdclk,
the DPLL sanity check can pass even if GOP/VBIOS is not loaded as BIOS
enables DPLL for integrated audio codec related programming.
So fisrt check if SWF18 is set and then follow through with other DPLL
and CDCLK verification. If not set then for sure we need to sanitize the
cdclock.

v2: Update the commit message for clarity (Siva)
v3: Correct the mask to check for bits[23:0] instead of only bits[16:0].
    Had missed checking for PIPE C altogether. Remaining are reserved (Siva)
v4: Use ILK_SWF macro for SWF register definitions. Taken from Ville's patch
    http://lists.freedesktop.org/archives/intel-gfx/2015-November/079480.html

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446726932-14078-1-git-send-email-shobhit.kumar@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915/bxt: Fix eDP panel fitting (v2)
Matt Roper [Wed, 4 Nov 2015 17:05:27 +0000 (09:05 -0800)]
drm/i915/bxt: Fix eDP panel fitting (v2)

BXT CRTC scaling uses the same gen9 codepaths as SKL; these codepaths
store panel fitter information in pipe_config->pch_pfit.  However since
HAS_PCH_SPLIT() is false for BXT we never actually wind up filling in
this structure (we wind up filling in pipe_config->gmch_pfit instead,
which is ignored when we go to program the hardware).  Make sure we
always take the PCH code path on gen9+ platforms.

v2: Use HAS_GMCH_DISPLAY() to more cleanly describe the platforms that
    actually want to use GMCH-style panel fitting.  (Ville)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446656727-3516-1-git-send-email-matthew.d.roper@intel.com
9 years agodrm/i915: change no_fbc_reason from enum to string
Paulo Zanoni [Tue, 27 Oct 2015 16:50:03 +0000 (14:50 -0200)]
drm/i915: change no_fbc_reason from enum to string

I wanted to add yet another check to intel_fbc_update() and realized
I would need to create yet another enum no_fbc_reason case. So I
remembered this patch series that Damien wrote a long time ago and
nobody ever reviewed, so I decided to reimplement it since the code
changed a lot since then.

Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445964628-30226-2-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
9 years agodrm/i915: Wait for object idle without locks in atomic_commit, v2.
Maarten Lankhorst [Tue, 18 Aug 2015 11:40:06 +0000 (13:40 +0200)]
drm/i915: Wait for object idle without locks in atomic_commit, v2.

Make pinning and waiting a separate step, and wait for object idle
without struct_mutex held.

Changes since v1:
- Do not wait when a reset is in progress.
- Remove call to i915_gem_object_wait_rendering for
  intel_overlay_do_put_image (Chris Wilson)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Change locking for struct_mutex, v3.
Maarten Lankhorst [Tue, 18 Aug 2015 11:40:05 +0000 (13:40 +0200)]
drm/i915: Change locking for struct_mutex, v3.

struct_mutex is being locked for every plane in intel_prepare_plane_fb
and intel_cleanup_plane_fb.

Require the caller to hold the mutex, and only acquire the mutex for
each helper call. This way the lock only needs to be acquired
twice in ->atomic_commit(). Once for pinning new framebuffers at the
start, the second time for unpinning old framebuffer.

Changes since v1:
- Use mutex_lock_interruptible instead of i915 variant,
  to prevent a deadlock when called from the reset code.
Changes since v2:
- Clarify struct_mutex is locked by the caller.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com> #v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Make wait_for_flips interruptible.
Maarten Lankhorst [Tue, 18 Aug 2015 11:40:05 +0000 (13:40 +0200)]
drm/i915: Make wait_for_flips interruptible.

Move it from intel_crtc_atomic_commit to prepare_plane_fb.
Waiting is done before committing, otherwise it's too late
to undo the changes.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Add extra plane information in debugfs.
Robert Fekete [Tue, 27 Oct 2015 15:58:32 +0000 (16:58 +0100)]
drm/i915: Add extra plane information in debugfs.

Extends i915_display_info so that for each active crtc also print
all planes associated with the pipe. This patch shows information
about each plane wrt format, size, position, rotation, and scaling.
This is very useful when debugging user space compositors that try
to utilize several planes for a commit.

V2: Fixed comments from Maarten, Ville, and Chris. Fixed printing of
16.16 fixpoint, better rotation bitmask management and some minor fixes

V3: Corrected state->src_x & 0x00ff to state->src_x & 0xffff...

Signed-off-by: Robert Fekete <robert.fekete@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445961512-25317-1-git-send-email-robert.fekete@linux.intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
9 years agodrm/i915/dma: enforce pr_<loglevel> consistency
Ioan-Adrian Ratiu [Fri, 30 Oct 2015 23:16:00 +0000 (01:16 +0200)]
drm/i915/dma: enforce pr_<loglevel> consistency

One branch of the if clause uses pr_info, the other pr_err; change
the 'false' branch to also use pr_info. This minor oversight has gone
unfixed since the initial vga_switcheroo implementation in 6a9ee8af.

Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446246960-22620-1-git-send-email-adi@adirat.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915: Don't complain about lack of ACPI video bios
Daniel Vetter [Fri, 23 Oct 2015 09:00:06 +0000 (11:00 +0200)]
drm/i915: Don't complain about lack of ACPI video bios

Another CI fail we have for no reason. Totally unjustified since
nothing fails at all.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445590806-23886-1-git-send-email-daniel.vetter@ffwll.ch
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Shut up GuC errors when it's disabled
Daniel Vetter [Fri, 23 Oct 2015 09:10:59 +0000 (11:10 +0200)]
drm/i915: Shut up GuC errors when it's disabled

DRM_ERROR an continue without any issues aren't allowed since that
causes noise in the CI system. But we absolutely want to have the
DRM_ERROR when we want to run with GuC.

For simplicity just short-circuit all the loader code when it's not
needed.

v2: Mika&Chris complained that I shouldn't hit send on patches written
before coffee kicks in.

v3: Make it compile at least ...

Cc: Alex Dai <yu.dai@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445591459-4327-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: make A0 wa's applied to A1
Tim Gore [Mon, 26 Oct 2015 10:48:58 +0000 (10:48 +0000)]
drm/i915: make A0 wa's applied to A1

Since A1 chips use the same GPU as A0, they need all the
same wa's in the i915 driver. Update some conditionals
to do this.

Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445856538-5417-1-git-send-email-tim.gore@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915/kbl: Add Kabylake GT4 PCI ID
Deepak S [Wed, 28 Oct 2015 19:21:12 +0000 (12:21 -0700)]
drm/i915/kbl: Add Kabylake GT4 PCI ID

v2: (Rodrigo) Rebase after commit 3cb27f38f
    ("drm/i915: remove an extra level of indirection in PCI ID list")

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446060072-19489-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915/kbl: Add Kabylake PCI ID
Deepak S [Wed, 28 Oct 2015 19:19:51 +0000 (12:19 -0700)]
drm/i915/kbl: Add Kabylake PCI ID

v2: separate out device info into different GT (Damien)
v3: Add is_kabylake to the KBL gt3 structuer (Damien)
    Sort the platforms in older -> newer order (Damien)

v4: Split platform definition since is_skylake=1 on
    kabylake structure was Nacked. (Rodrigo)

v5: (Rodrigo) Rebase after commit 3cb27f38f
("drm/i915: remove an extra level of indirection in PCI ID list")

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446059991-17033-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915/kbl: Introduce Kabylake platform defition.
Rodrigo Vivi [Wed, 28 Oct 2015 11:16:45 +0000 (04:16 -0700)]
drm/i915/kbl: Introduce Kabylake platform defition.

Kabylake is a Intel® Processor containing Intel® HD Graphics
following Skylake.

It is Gen9p5, so it inherits everything from Skylake.

Let's start by adding the platform separated from Skylake
but reusing most of all features, functions etc. Later we
rebase the PCI-ID patch without is_skylake=1
so we don't replace what original Author did there.

Few IS_SKYLAKEs if statements are not being covered by this patch
on purpose:
   - Workarounds: Kabylake is derivated from Skylake H0 so no
        W/As apply here.
   - GuC: A following patch removes Kabylake support with an
        explanation: No firmware available yet.
   - DMC/CSR: Done in a separated patch since we need to be carefull
            and load the version for revision 7 since
      Kabylake is Skylake H0.

v2: relative cleaner commit message and added the missed
    IS_KABYLAKE to intel_i2c.c as pointed out by Jani.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915: Define IS_BROXTON properly.
Rodrigo Vivi [Tue, 27 Oct 2015 17:14:54 +0000 (10:14 -0700)]
drm/i915: Define IS_BROXTON properly.

Kabylake will also be defined as gen9 and !is_skylake.
So we need start by creating a proper Broxton
definition, otherwise we will break broxton with the
introduction of Kabylake.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445966099-1640-2-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915: remove an extra level of indirection in PCI ID list
Jani Nikula [Wed, 28 Oct 2015 17:33:09 +0000 (19:33 +0200)]
drm/i915: remove an extra level of indirection in PCI ID list

Add the PCI IDs directly in the pciidlist array instead of defining an
extra macro. The minor benefit from this is neater diffs when adding to
the end of the list.

v2: drop the "aka" comment (Ville)

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446053589-21283-1-git-send-email-jani.nikula@intel.com
9 years agodrm/i915: Recover all available ringbuffer space following reset
Chris Wilson [Thu, 3 Sep 2015 12:01:40 +0000 (13:01 +0100)]
drm/i915: Recover all available ringbuffer space following reset

Having flushed all requests from all queues, we know that all
ringbuffers must now be empty. However, since we do not reclaim
all space when retiring the request (to prevent HEADs colliding
with rapid ringbuffer wraparound) the amount of available space
on each ringbuffer upon reset is less than when we start. Do one
more pass over all the ringbuffers to reset the available space

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
9 years agodrm/i915: Use paramtrized WRPLL_CTL()
Ville Syrjälä [Fri, 18 Sep 2015 17:03:33 +0000 (20:03 +0300)]
drm/i915: Use paramtrized WRPLL_CTL()

v2: Rebase due to SKL_DPLLx usage

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1442595836-23981-21-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915: Add NEEDS_FORCEWAKE() checks for vlv/chv
Ville Syrjälä [Thu, 22 Oct 2015 12:35:00 +0000 (15:35 +0300)]
drm/i915: Add NEEDS_FORCEWAKE() checks for vlv/chv

Include an early NEEDS_FORCEWAKE() check for vlv and chv.
Hopefully that will avoid doing so many range checks in for many
register accesses (at least for all display registers).

Note that vlv already had the check in the write path since it shares
the gen6+ code for that.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Respin vlv/chv reagister access to look more like SKL
Ville Syrjälä [Thu, 22 Oct 2015 12:34:59 +0000 (15:34 +0300)]
drm/i915: Respin vlv/chv reagister access to look more like SKL

Change the fw domain handling in the vlv/chv register read/write
functions to look more like the SKL code, ie. have a single
__force_wake_get() get call instead of multiple ones.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Minor style nits in intel_uncore.c
Ville Syrjälä [Thu, 22 Oct 2015 12:34:58 +0000 (15:34 +0300)]
drm/i915: Minor style nits in intel_uncore.c

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Read FORCEWAKE registers with I915_READ_FW()
Ville Syrjälä [Thu, 22 Oct 2015 12:34:57 +0000 (15:34 +0300)]
drm/i915: Read FORCEWAKE registers with I915_READ_FW()

Change FORCEWAKE & co. reads for the error state to use I915_READ_FW().
Reading a FORCEWAKE register using a function that can frob forcewake
just seems wrong.

There is a check to skip grabbing the forcewake for accessing FORCEWAKE
in intel_uncore.c, but there's no such check for FORCEWAKE_MT. So no
idea what is currently happening with FORCEWAKE_MT reads. FORCEWAKE_VLV
is fortunately outside the forcewake range anyway, so no actual issue
with that one.

So let's just make the rule that you can't access FORCEWAKE registers with
the normal I915_READ() stuff, and we can drop the extra FORCEWAKE check
from NEEDS_FORCEWAKE(). While at it use NEEDS_FORCEWAKE() on BDW, where
it was skipped for whatever bikeshed reason that I've already forgotten.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Turn __raw_i915_read8() & co. in to inline functions
Ville Syrjälä [Thu, 22 Oct 2015 12:34:56 +0000 (15:34 +0300)]
drm/i915: Turn __raw_i915_read8() & co. in to inline functions

There's no need for __raw_i915_read8() & co. to be macros, so make them
inline functions. To avoid typo mistakes generate the inline functions
using preprocessor templates.

We have a few users of the raw register acces functions outside
intel_uncore.c, so let's also move the functions into intel_drv.h.

While doing that switch I915_READ_FW() & co. to use the
__raw_i915_read() functions, and use the _FW macros everywhere
outside intel_uncore.c where we want to read registers without
grabbing forcewake and whatnot. The only exception is
i915_check_vgpu() which itself gets called from intel_uncore.c,
so using the __raw_i915_read stuff there seems appropriate.

v2: Squash in the intel_uncore.c->i915_drv.h move
    Convert I915_READ_FW() to use __raw_i915_read(), and use
    I915_READ_FW() outside of intel_uncore.c (Chris)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445517300-28173-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
9 years agodrm/i915: Cope with request list state change during error state capture
Tomas Elf [Mon, 19 Oct 2015 16:51:57 +0000 (17:51 +0100)]
drm/i915: Cope with request list state change during error state capture

Since we're not synchronizing the ring request list during error state capture
the request list state might change between the time the corresponding error
request list was allocated and dimensioned to the time when the ring request
list is actually captured into the error state. If this happens then do an
early exit and be aware that the captured error state might not be fully
reliable.

* v2:
- Chris Wilson: Removed WARN_ON from size check since having the error state
  request list and the live driver request list diverge like this is a
  legitimate behaviour.

- Tomas Elf: Removed update of num_request field since this made no sense. Just
  exit and move on.

* v3:
- Chris Wilson: Removed error message at the point of early exit. The user is
  not interested in any state changes happening during the error state capture,
  only in the state that we're trying to capture at the point of the error.

Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agoRevert "drm/i915: Add soft-pinning API for execbuffer"
Daniel Vetter [Fri, 23 Oct 2015 10:01:00 +0000 (12:01 +0200)]
Revert "drm/i915: Add soft-pinning API for execbuffer"

This reverts commit 510567234180d7d65d2db9f7bd8424cabef13d3c.

I somehow managed to combine a patch from Tomas Elf with a totally
unrelated commit message from Chris Wilson. Let's revert this and
reapply properly.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
9 years agodrm/i915: Update DRIVER_DATE to 20151023
Daniel Vetter [Fri, 23 Oct 2015 09:57:40 +0000 (11:57 +0200)]
drm/i915: Update DRIVER_DATE to 20151023

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: shut up gen8+ SDE irq dmesg noise
Daniel Vetter [Fri, 23 Oct 2015 08:56:12 +0000 (10:56 +0200)]
drm/i915: shut up gen8+ SDE irq dmesg noise

We get tons of cases where the master interrupt handler apparently set
a bit, with the SDEIIR disagreeing. No idea what's going on there, but
it's consistent on gen8+, no one seems to care about it and it's
making CI results flaky.

Shut it up.

No idea what's going on here, but we've had fun with PCH interrupts
before:

commit 44498aea293b37af1d463acd9658cdce1ecdf427
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Feb 22 17:05:28 2013 -0300

    drm/i915: also disable south interrupts when handling them

Note that there's a regression report in Bugzilla, and other
regression reports on the mailing lists keep croping up. But no ill
effects have ever been reported. But for paranoia still keep the
message at a debug level as a breadcrumb, just in case.

This message was introduced in

commit 38cc46d73ed99dd7002f1406002e52d7975d16cc
Author: Oscar Mateo <oscar.mateo@intel.com>
Date:   Mon Jun 16 16:10:59 2014 +0100

    drm/i915/bdw: Ack interrupts before handling them (GEN8)

v2: Improve commit message a bit.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445590572-23631-2-git-send-email-daniel.vetter@ffwll.ch
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92084
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80896
Acked-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Grab execlist spinlock to avoid post-reset concurrency issues.
Tomas Elf [Mon, 19 Oct 2015 15:32:32 +0000 (16:32 +0100)]
drm/i915: Grab execlist spinlock to avoid post-reset concurrency issues.

Grab execlist lock when cleaning up execlist queues after GPU reset to avoid
concurrency problems between the context event interrupt handler and the reset
path immediately following a GPU reset.

* v2 (Chris Wilson):
Do execlist check and use simpler form of spinlock functions.

Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Add soft-pinning API for execbuffer
Chris Wilson [Tue, 6 Oct 2015 10:53:11 +0000 (11:53 +0100)]
drm/i915: Add soft-pinning API for execbuffer

Userspace can pass in an offset that it presumes the object is located
at. The kernel will then do its utmost to fit the object into that
location. The assumption is that userspace is handling its own object
locations (for example along with full-ppgtt) and that the kernel will
rarely have to make space for the user's requests.

v2: Fix i915_gem_evict_range() (now evict_for_vma) to handle ordinary
and fixed objects within the same batch

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Daniel, Thomas" <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Calculate watermark configuration during atomic check (v2)
Matt Roper [Thu, 24 Sep 2015 22:53:18 +0000 (15:53 -0700)]
drm/i915: Calculate watermark configuration during atomic check (v2)

v2: Don't forget to actually check the cstate->active value when
    tallying up the number of active CRTC's.  (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59561/
9 years agodrm/i915: Don't set plane visible during HW readout if CRTC is off
Matt Roper [Thu, 24 Sep 2015 22:53:17 +0000 (15:53 -0700)]
drm/i915: Don't set plane visible during HW readout if CRTC is off

We already ensure that pstate->visible = false when crtc->active = false
during runtime programming; make sure we follow the same logic when
reading out initial hardware state.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59564/
9 years agodrm/i915: Calculate ILK-style watermarks during atomic check (v3)
Matt Roper [Thu, 24 Sep 2015 22:53:16 +0000 (15:53 -0700)]
drm/i915: Calculate ILK-style watermarks during atomic check (v3)

Calculate pipe watermarks during atomic calculation phase, based on the
contents of the atomic transaction's state structure.  We still program
the watermarks at the same time we did before, but the computation now
happens much earlier.

While this patch isn't too exciting by itself, it paves the way for
future patches.  The eventual goal (which will be realized in future
patches in this series) is to calculate multiple sets up watermark
values up front, and then program them at different times (pre- vs
post-vblank) on the platforms that need a two-step watermark update.

While we're at it, s/intel_compute_pipe_wm/ilk_compute_pipe_wm/ since
this function only applies to ILK-style watermarks and we have a
completely different function for SKL-style watermarks.

Note that the original code had a memcmp() in ilk_update_wm() to avoid
calling ilk_program_watermarks() if the watermarks hadn't changed.  This
memcmp vanishes here, which means we may do some unnecessary result
generation and merging in cases where watermarks didn't change, but the
lower-level function ilk_write_wm_values already makes sure that we
don't actually try to program the watermark registers again.

v2: Squash a few commits from the original series together; no longer
    leave pre-calculated wm's in a separate temporary structure since
    it's easier to follow the logic if we just cut over to using the
    pre-calculated values directly.

v3:
 - Pass intel_crtc instead of drm_crtc to .compute_pipe_wm() entrypoint
   and use intel_atomic_get_crtc_state() to avoid need for extra
   casting.  (Ander)
 - Drop unused intel_check_crtc() function prototype.  (Ander)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60363/
9 years agodrm/i915: Calculate pipe watermarks into CRTC state (v3)
Matt Roper [Thu, 24 Sep 2015 22:53:15 +0000 (15:53 -0700)]
drm/i915: Calculate pipe watermarks into CRTC state (v3)

A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.

While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.

v2: Don't move cxsr_allowed to state (Maarten)

v3: Only calculate watermarks in state.  Still keep active watermarks in
    intel_crtc itself.  (Ville)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59556/
9 years agodrm/i915: Refactor ilk_update_wm (v3)
Ville Syrjälä [Thu, 24 Sep 2015 22:53:14 +0000 (15:53 -0700)]
drm/i915: Refactor ilk_update_wm (v3)

Split ilk_update_wm() into two parts; one doing the programming
and the other the calculations.

v2: Fix typo in commit message

v3 (by Matt): Heavily rebased for current codebase.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60366/
9 years agodrm/i915: Drop intel_update_sprite_watermarks
Matt Roper [Thu, 24 Sep 2015 22:53:13 +0000 (15:53 -0700)]
drm/i915: Drop intel_update_sprite_watermarks

The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update.  However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call.  Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60372/
9 years agodrm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check
Matt Roper [Thu, 24 Sep 2015 22:53:12 +0000 (15:53 -0700)]
drm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check

Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.

Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60367/
9 years agodrm/i915: Fix formatting for gen8_cs_irq_handler
Daniel Vetter [Wed, 21 Oct 2015 08:20:33 +0000 (10:20 +0200)]
drm/i915: Fix formatting for gen8_cs_irq_handler

Requested by Chris, and since we're no longer rebasing the -next queue
I can't rectify history.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445415633-21897-1-git-send-email-daniel.vetter@ffwll.ch
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/guc: Add GuC css header parser
Alex Dai [Mon, 19 Oct 2015 23:10:54 +0000 (16:10 -0700)]
drm/i915/guc: Add GuC css header parser

The size / offset information of all firmware ingredients are
now caculated from header. Driver will validate the header and
rsa key size. If any component is out of boundary, driver will
reject the loading too.

v6: Clean up warnings from make docs

v5: Tidy up GuC titles in kernel/Doc

v4: Now using 'size_dw' for those defined in css_header

v3: 1) Move DOC to intel_guc_fwif.h right before css_header
definition. Add more comments.
    2) Change 'size' to 'len' or 'length' to avoid confusion.
    3) Add UOS_RSA_SCRATCH_MAX_COUNT according to BSpec. And
driver validate size of RSA key now.
    4) Add fw component size/offset info to intel_guc_fw.

v2: Add indent into DOC to make fixed-width format rather than
change the tmpl.

v1: 1) guc_css_header is defined as __packed now
    2) Add and correct GuC related topics in kernel/Doc

Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: add helpers for platform specific revision id range checks
Jani Nikula [Tue, 20 Oct 2015 12:22:02 +0000 (15:22 +0300)]
drm/i915: add helpers for platform specific revision id range checks

Revision checks are almost always accompanied by a platform check. (The
exceptions are platform specific code.) Add helpers to check for a
platform and a revision range: IS_SKL_REVID() and IS_BXT_REVID(). In
most places this simplifies and clarifies the code. It will be obvious
that revid macros are used for the correct platform.

This should make it easier to find all the revision checks for
workarounds for each platform, and make it easier to remove them once we
drop support for early hardware revisions.

This should also make it easier to differentiate between Skylake and
Kabylake revision checks when Kabylake support is added.

v2: rebase

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-3-git-send-email-jani.nikula@intel.com
9 years agodrm/i915/bxt: add revision id for A1 stepping and use it
Jani Nikula [Tue, 20 Oct 2015 12:22:01 +0000 (15:22 +0300)]
drm/i915/bxt: add revision id for A1 stepping and use it

Prefer inclusive ranges for revision checks rather than "below B0". Per
specs A2 is not used, so revid <= A1 matches revid < B0.

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-2-git-send-email-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915: remove parens around revision ids
Jani Nikula [Tue, 20 Oct 2015 12:22:00 +0000 (15:22 +0300)]
drm/i915: remove parens around revision ids

Totally unnecessary.

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-1-git-send-email-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
9 years agodrm/i915: Do not wait for flips in intel_crtc_disable_noatomic.
Maarten Lankhorst [Mon, 19 Oct 2015 15:09:23 +0000 (17:09 +0200)]
drm/i915: Do not wait for flips in intel_crtc_disable_noatomic.

intel_crtc_disable_noatomic is called from hw readout during init, resume and possibly reset.
During init it's too early to have a page flip queued, before suspending all page flips
should be finished and during hw reset all page flips should be removed.

It's a bug when there are pending flips here, complain with WARN_ON instead of handling it.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/562507A3.3080901@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl: Consider plane rotation when calculating stride in skl_do_mmio_flip
Tvrtko Ursulin [Tue, 20 Oct 2015 15:20:21 +0000 (16:20 +0100)]
drm/i915/skl: Consider plane rotation when calculating stride in skl_do_mmio_flip

Previously rotation was ignored and wrong stride programmed
into the plane registers resulting in a corrupt image on screen.

v2: Do not access potentialy old plane state at flip time,
    but store the rotation value at the time of queing the flip.
    (Ville)

v3: No need to pass rotation to intel_queue_mmio_flip since it
    is available in the crtc. (Ville)

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Testcase: igt/kms_rotation_crc/primary-rotation-90-flip-stress (SKL)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl: Assume no scaling is available when things are not as expected
Tvrtko Ursulin [Tue, 20 Oct 2015 16:17:07 +0000 (17:17 +0100)]
drm/i915/skl: Assume no scaling is available when things are not as expected

Cdclk < crtc_clock is not allowed and suggests a different problem
elsewhere in the code.

It is more robust and safe to assume no scaling is possible in
this case with no other downsides since it will also WARN_ON_ONCE
so that this definitely gets noticed.

Call it an assert to help new platform bring-up in simulation.

v2: Better commit msg and use WARN_ON_ONCE to signify the unexpectedness.

v3: Move zero crtc_clock check under the warn. (Ville)

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl: If needed sanitize bios programmed cdclk
Shobhit Kumar [Tue, 20 Oct 2015 12:43:12 +0000 (18:13 +0530)]
drm/i915/skl: If needed sanitize bios programmed cdclk

Especially in cases where pre-os does not enable display, cdclk might
not be in sane state. During sanitization initialize cdclk with maximum
value till we get dynamic cdclk support.

v2: Check if BIOS programmed correctly rather than always calling init
    - Do validation of programmed cdctl and what it is expected
    - Only do slk_init_cdclk if validation failed else reuse BIOS
      programmed value

v3: Move the validation logic in a separate sanitize function (Ville)

v4: No need to check LCPLL after sanitize and use max_cdclk_freq instead
    of hardcoded value (Ville)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344992-14658-1-git-send-email-shobhit.kumar@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Break out common code from gen8_gt_irq_handler
Nick Hoath [Tue, 20 Oct 2015 09:23:52 +0000 (10:23 +0100)]
drm/i915: Break out common code from gen8_gt_irq_handler

Break out common code from gen8_gt_irq_handler and put it in to
an always inlined function. gcc optimises out the shift at compile
time. (Thomas Daniel/Daniel Vetter/Chris Wilson)

Issue: VIZ-4277
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1445333036-22164-3-git-send-email-nicholas.hoath@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i195: Rename gt_irq_handler variable
Nick Hoath [Tue, 20 Oct 2015 09:23:51 +0000 (10:23 +0100)]
drm/i195: Rename gt_irq_handler variable

Renamed tmp variable to the more descriptive iir. (Daniel Vetter/
Thomas Daniel)

Issue: VIZ-4277
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445333036-22164-2-git-send-email-nicholas.hoath@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v4)
Matt Roper [Thu, 24 Sep 2015 22:53:11 +0000 (15:53 -0700)]
drm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v4)

Just pull the info out of the state structures rather than staging
it in an additional set of structures.  To make this more
straightforward, we change the signature of several internal WM
functions to take the crtc state as a parameter.

v2:
 - Don't forget to skip cursor planes on a loop in the DDB allocation
   function to match original behavior.  (Ander)
 - Change a use of intel_crtc->active to cstate->active.  They should
   be identical, but it's better to be consistent.  (Ander)
 - Rework more function signatures to pass states rather than crtc for
   consistency. (Ander)

v3:
  - Add missing "+ 1" to skl_wm_plane_id()'s 'overlay' case. (Maarten)
  - Packed formats should pass '0' to drm_format_plane_cpp(), not 1.
    (Maarten)
  - Drop unwanted WARN_ON() for disabled planes when calculating data
    rate for SKL.  (Maarten)

v4:
 - Don't include cursor plane in total relative data rate calculation;
   we've already handled the cursor allocation earlier.
 - Fix 'bytes_per_pixel' calculation braindamage.  Somehow I hardcoded
   the NV12 format as a parameter rather than the actual
   fb->pixel_format, and even then still managed to get the format plane
   wrong.  (Ville)
 - Use plane->state->fb rather than plane->fb in
   skl_allocate_pipe_ddb(); the plane->fb pointer isn't updated until
   after we've done our watermark recalculation, so it has stale
   values.  (Bob Paauwe)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by(v3): Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Paauwe, Bob J <bob.j.paauwe@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-September/077060.html
References: http://lists.freedesktop.org/archives/intel-gfx/2015-October/077721.html
Smoke-tested-by(v4): Paulo Zanoni <paulo.r.zanoni@intel.com> (SKL)
Link: http://patchwork.freedesktop.org/patch/61968/
9 years agodrm/i915: Improve kernel-doc for i915_audio_component struct
David Henningsson [Fri, 16 Oct 2015 09:24:24 +0000 (11:24 +0200)]
drm/i915: Improve kernel-doc for i915_audio_component struct

Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1444987464-8657-1-git-send-email-david.henningsson@canonical.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Report context GTT size
Chris Wilson [Wed, 14 Oct 2015 13:17:11 +0000 (14:17 +0100)]
drm/i915: Report context GTT size

Since the beginning we have conflated the size of the global GTT with
that of the per-process context sizes. In recent times (gen8+), those
are no longer the same where the global GTT is limited to 2/4GiB but the
per-process GTT may be anything up to 256TiB. Userspace knows nothing of
this discrepancy and outside of one or two hacks, uses the getaperture
ioctl to determine the maximum size it can use. Let's leave that as
reporting the global GTT and use the context reporting method to
describe the per-process value (which naturally fallsback to reporting
the aliasing or global on older platforms, so userspace can always use
this method where available).

Testcase: igt/gem_userptr_blits/minor-normal-sync
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90065
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Map the ringbuffer using WB on LLC machines
Chris Wilson [Thu, 8 Oct 2015 12:39:54 +0000 (13:39 +0100)]
drm/i915: Map the ringbuffer using WB on LLC machines

If we have llc coherency, we can write directly into the ringbuffer
using ordinary cached writes rather than forcing WC access.

v2: An important consequence is that we can forgo the mappable request
for WB ringbuffers, allowing for many more simultaneous contexts.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/gen8: Flip the 48b switch
Michel Thierry [Wed, 30 Sep 2015 14:36:19 +0000 (15:36 +0100)]
drm/i915/gen8: Flip the 48b switch

Use 48b addresses if hw supports it (i915.enable_ppgtt=3).
Update the sanitize_enable_ppgtt for 48 bit PPGTT mode.

Note, aliasing PPGTT remains 32b only.

v2: s/full_64b/full_48b/. (Akash)
v3: Add sanitize_enable_ppgtt changes until here. (Akash)
v4: Update param description (Chris)

Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Only call commit_planes when there are things to commit.
Maarten Lankhorst [Wed, 23 Sep 2015 14:29:39 +0000 (16:29 +0200)]
drm/i915: Only call commit_planes when there are things to commit.

The atomic helpers set planes_changed on a crtc_state if there is
any plane_state bound to that crtc. If there's none and there is
no pipe update required the crtc has nothing to update, so vblank
evasion can be skipped.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Only run commit when crtc is active, v2.
Maarten Lankhorst [Wed, 23 Sep 2015 14:29:38 +0000 (16:29 +0200)]
drm/i915: Only run commit when crtc is active, v2.

The crtc->active guards are no longer needed now that all state
updates are outside the commit.

Changes since v1:
- Only check crtc->state->active before calling commit_planes_on_crtc.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Only commit active planes when updating planes during reset.
Maarten Lankhorst [Wed, 23 Sep 2015 14:29:37 +0000 (16:29 +0200)]
drm/i915: Only commit active planes when updating planes during reset.

In the next commit commit_plane will no longer check if the crtc is active.
To prevent issues with legacy page flips the check should be performed inside
update_primary_planes.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Update legacy primary state outside the commit hook, v2.
Maarten Lankhorst [Wed, 23 Sep 2015 14:29:36 +0000 (16:29 +0200)]
drm/i915: Update legacy primary state outside the commit hook, v2.

This should allow not running plane commit when the crtc is off.
While the atomic helpers update those, crtc->x/y is only updated
during modesets, and primary plane is updated after this function
returns.

Unfortunately non-atomic watermarks and fbc still depend on this
state inside i915, so it has to be kept in sync.

Changes since v1:
- Add comment that the legacy state is updated for fbc.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Make prepare_plane_fb fully interruptible.
Maarten Lankhorst [Wed, 23 Sep 2015 11:27:09 +0000 (13:27 +0200)]
drm/i915: Make prepare_plane_fb fully interruptible.

Now that we agreed on not preserving framebuffers pinning is finally
allowed to fail because of signals. Use this to make pinning
and acquire the mutex in an interruptible way too.

Unpinning is still uninterruptible, because it happens as a cleanup
of old state, or undoing pins after one of the pins failed.

The intel_pin_and_fence_fb_obj in page_flip will also wait interruptibly,
and can be aborted now.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Make plane fb tracking work correctly, v2.
Maarten Lankhorst [Wed, 23 Sep 2015 11:27:08 +0000 (13:27 +0200)]
drm/i915: Make plane fb tracking work correctly, v2.

atomic->disabled_planes is a hack that had to exist because
prepare_fb was only called when a new fb was set. This messed
up fb tracking in some circumstances like aborts from
interruptible waits. As a result interruptible waiting in
prepare_plane_fb was forbidden, but other errors could still
cause frontbuffer tracking to be messed up.

Now that prepare_fb is always called, this hack is no longer
required and prepare_fb may fail without consequences.

Changes since v1:
- Clean up a few fb tracking warnings by changing plane->fb to
  plane->state->fb.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl: Making DC6 entry is the last call in suspend flow.
Animesh Manna [Tue, 29 Sep 2015 05:31:59 +0000 (11:01 +0530)]
drm/i915/skl: Making DC6 entry is the last call in suspend flow.

Mmio register access after dc6/dc5 entry is not allowed when
DC6 power states are enabled according to bspec (bspec-id 0527),
so enabling dc6 as the last call in suspend flow.

Addtional note from Imre:

Currently we keep DC6 enabled during modesets and DPAUX transfers, which
is not allowed according to the specification. This can lead at least to
PLL locking failures, DPAUX timeouts and prevent deeper package power
states (PC9/10). Fix this for now by enabling DC6 only when we know the
above events (modeset, DPAUX) can't happen.

This a temporary solution as some issues are still unsolved as described
in [1] and [2], we'll address those as a follow-up.

[1]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077669.html
[2]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077787.html

v1: Initial version.

v2: Based on review comment from Daniel,
- created a seperate patch for csr uninitialization set call.

v3: Rebased on top of latest code.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Kill the leftover RMW from ivb_sprite_disable()
Ville Syrjälä [Thu, 15 Oct 2015 14:04:04 +0000 (17:04 +0300)]
drm/i915: Kill the leftover RMW from ivb_sprite_disable()

We still had one lingering RMW in ivb_sprite_disable(), all the other
RMWs were killed off from the sprite code some time ago. Kill the
straggler too.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: restore ggtt double-bind avoidance
Daniel Vetter [Thu, 15 Oct 2015 12:23:01 +0000 (14:23 +0200)]
drm/i915: restore ggtt double-bind avoidance

This was accidentally lost in

commit 75d04a3773ecee617847de963ae4195d6aa74c28
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Tue Apr 28 17:56:17 2015 +0300

    drm/i915/gtt: Allocate va range only if vma is not bound

While at it implement an improved version suggested by Chris which
avoids the double-bind irrespective of what type of bind is done
first.

Note that this exact bug was already addressed in

commit d0e30adc42d979e4adc36b6c112b57337423b70c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Jul 29 20:02:48 2015 +0100

    drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt

but the problem is still that originally in

commit 0875546c5318c85c13d07014af5350e9000bc9e9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Apr 20 09:04:05 2015 -0700

    drm/i915: Fix up the vma aliasing ppgtt binding

if forgotten to take into account there case where we have a
GLOBAL_BIND before a LOCAL_BIND. This patch here fixes that.

v2: Pimp commit message and revert the partial fix.

v3: Split into two functions to specialize on aliasing_ppgtt y/n.

v4: WARN_ON for paranoia in the init sequence, since the ggtt probe
and aliasing ppgtt setup are far apart.

v5: Style nits.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://mid.gmane.org/1444911781-32607-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl: Enable pipe gamma for sprite planes.
Bob Paauwe [Thu, 27 Aug 2015 20:46:30 +0000 (13:46 -0700)]
drm/i915/skl: Enable pipe gamma for sprite planes.

Since SKL has universal planes, we should configure the sprite planes
and the primary plane the same.  For the primary plane we do enable
the pipe gamma on the plane so do the same for the non-primary planes.

Without this, the pipe CRC values will be different for something
displayed on the primary plane and something displayed on a sprite
plane when the ARGB8888 format is used.

Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/skl+: Enable pipe CSC on cursor planes. (v2)
Bob Paauwe [Mon, 31 Aug 2015 21:03:30 +0000 (14:03 -0700)]
drm/i915/skl+: Enable pipe CSC on cursor planes. (v2)

Extend this to SKL and BXT as it's needed for these platforms as well.

v2: Change if condition to HAS_DDI() instead of listing each platform
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agoMAINTAINERS: add link to the Intel Graphics for Linux web site
Jani Nikula [Tue, 13 Oct 2015 08:16:48 +0000 (11:16 +0300)]
MAINTAINERS: add link to the Intel Graphics for Linux web site

There's plenty of drm/i915 related hardware and software documentation,
and firmware downloads for the latest platforms.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Move skl/bxt gt specific workarounds to ring init
Mika Kuoppala [Mon, 12 Oct 2015 10:20:59 +0000 (13:20 +0300)]
drm/i915: Move skl/bxt gt specific workarounds to ring init

Some registers are, naturally, lost in gpu reset/suspend cycle.
And some registers, for example in display domain, are not subject
to gpu reset so they retain their contents.

As hang recovery triggers a reset, recoverable gpu hang can currently
flush out essential workarounds and cause havoc later on.

When register GEN8_GARBNTL is missing the WaEnableGapsTsvCreditFix:skl,
it can cause random system hangs [1]. This workaround was added in:
commit 245d96670d26 ("drm/i915:skl: Add WaEnableGapsTsvCreditFix")
But another set of system hangs were observed and the failure pattern
indicated that there was random gpu hang preceding the system hang [2].
This lead to the realization that we lose this workaround and BDW_SCRATCH1
on reset.

Add these workarounds setup in display init to skl/bxt ring init
where LRI workarounds are also setup. This way their setup is not
dependent on display side init.

References: [1] https://bugs.freedesktop.org/show_bug.cgi?id=90854
References: [2] https://bugs.freedesktop.org/show_bug.cgi?id=92315
Reported-by: Tomi Sarvela <tomix.p.sarvela@intel.com>
Cc: Tomi Sarvela <tomix.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomi Sarvela <tomix.p.sarvela@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Drop i915_gem_obj_is_pinned() from set-cache-level
Chris Wilson [Fri, 9 Oct 2015 13:11:27 +0000 (14:11 +0100)]
drm/i915: Drop i915_gem_obj_is_pinned() from set-cache-level

Since the remove of the pin-ioctl, we only care about not changing the
cache level on buffers pinned to the hardware as indicated by
obj->pin_display. By knowing that only objects pinned to the hardware
will have an elevated vma->pin_count, so we can coallesce many of the
linear walks over the obj->vma_list.

v2: Try and retrospectively add comments explaining the steps in
rebinding the active VMA.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: revert a few more watermark commits
Paulo Zanoni [Fri, 9 Oct 2015 21:22:43 +0000 (18:22 -0300)]
drm/i915: revert a few more watermark commits

This is a squash of the following commits:

Revert "drm/i915: Drop intel_update_sprite_watermarks"
This reverts commit 47c99438b52d12df50e182583634a4cfede3c920.

Revert "drm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check"
This reverts commit 7809e5ae35b9d8d0710f0874b2e3f10be144e38b.

Revert "drm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v3)"
This reverts commit 3a05f5e2e78eab7ffe816abb59b6769e331a1957.

With these reverts, SKL finally stops failing every single FBC test
with FIFO underrun error messages. After some brief testing, it also
seems that this commit prevents the machine from completely freezing
when we run igt/kms_fbc_crc (see fd.o #92355).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92355
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Remove dev_priv argument from NEEDS_FORCE_WAKE
Ville Syrjälä [Fri, 18 Sep 2015 17:03:46 +0000 (20:03 +0300)]
drm/i915: Remove dev_priv argument from NEEDS_FORCE_WAKE

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Clean up LVDS register handling
Ville Syrjälä [Fri, 18 Sep 2015 17:03:45 +0000 (20:03 +0300)]
drm/i915: Clean up LVDS register handling

Keep single 'lvds_reg' and 'lvds' variable around in
intel_lvds_init(), and read it just once at the start.

Also intel_lvds_get_config() doesn't need to figure out which reg to use
since it can just consult lvds_encoder->reg.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Throw out some useless variables
Ville Syrjälä [Tue, 22 Sep 2015 16:50:01 +0000 (19:50 +0300)]
drm/i915: Throw out some useless variables

Drop some useless 'reg' variables when we only use them once.

v2: A few more, including a few variable moves

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Parametrize and fix SWF registers
Ville Syrjälä [Fri, 18 Sep 2015 17:03:43 +0000 (20:03 +0300)]
drm/i915: Parametrize and fix SWF registers

Parametrize the SWF registers. This also fixes the register offsets,
which were mostly garbage in the old defines.

Also save/restore only as many SWF registers that each platform has.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: s/PIPE_FRMCOUNT_GM45/PIPE_FRMCOUNT_G4X/ etc.
Ville Syrjälä [Fri, 18 Sep 2015 17:03:42 +0000 (20:03 +0300)]
drm/i915: s/PIPE_FRMCOUNT_GM45/PIPE_FRMCOUNT_G4X/ etc.

The PIPE_FRMCOUNT_GM45 and PIPE_FLIPCOUNT_GM45 names have bothered me
for a long time. The work equally well for ELK and onwards, so let's
s/GM45/G4X/.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Turn GEN5_ASSERT_IIR_IS_ZERO() into a function
Ville Syrjälä [Fri, 18 Sep 2015 17:03:41 +0000 (20:03 +0300)]
drm/i915: Turn GEN5_ASSERT_IIR_IS_ZERO() into a function

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Fix a few bad hex numbers in register defines
Ville Syrjälä [Fri, 18 Sep 2015 17:03:40 +0000 (20:03 +0300)]
drm/i915: Fix a few bad hex numbers in register defines

A few register mask defines were missing the '0x' from hex numbers. Or
at least I assume those were meant to be hex numbers. Put the '0x' in
place.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Protect register macro arguments
Ville Syrjälä [Fri, 18 Sep 2015 17:03:39 +0000 (20:03 +0300)]
drm/i915: Protect register macro arguments

Always put parens around macro argument evaluations.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Include gpio_mmio_base in GMBUS reg defines
Ville Syrjälä [Fri, 18 Sep 2015 17:03:38 +0000 (20:03 +0300)]
drm/i915: Include gpio_mmio_base in GMBUS reg defines

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Parametrize HSW video DIP data registers
Ville Syrjälä [Fri, 18 Sep 2015 17:03:37 +0000 (20:03 +0300)]
drm/i915: Parametrize HSW video DIP data registers

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Eliminate weird parameter inversion from BXT PPS registers
Ville Syrjälä [Mon, 12 Oct 2015 16:41:08 +0000 (19:41 +0300)]
drm/i915: Eliminate weird parameter inversion from BXT PPS registers

v2: Keep using the same registers (PCH_*) instead of accidentally
    starting to use the other ones (BXT_*)2) (Jesse)

Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Hold dev->event_lock whilst inspecting intel_crtc->unpin_work
Chris Wilson [Sat, 10 Oct 2015 09:44:32 +0000 (10:44 +0100)]
drm/i915: Hold dev->event_lock whilst inspecting intel_crtc->unpin_work

We should serialise access to the intel_crtc->unpin_work through the
dev->event_lock spinlock. It should not be possible for it to disappear
without severe error as the mmio_flip worker has not tagged the
unpin_work pending flip-completion. Similarly if the error exists, just
taking the unpin_work whilst holding the spinlock and then using it
unserialised just masks the race. (It is supposed to be valid as the
unpin_work exists until the flip completion interrupt which should not
fire until we flush the mmio writes to update the display base which is
the last time we access the unpin_work from the kthread.)

References: https://bugs.freedesktop.org/show_bug.cgi?id=92335
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agoi915: switch from acpi_os_ioremap to memremap
Williams, Dan J [Mon, 12 Oct 2015 21:12:57 +0000 (21:12 +0000)]
i915: switch from acpi_os_ioremap to memremap

i915 expects the OpRegion to be cached (i.e. not __iomem), so explicitly
map it with memremap rather than the implied cache setting of
acpi_os_ioremap().

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Drop unnecessary #include <linux/vga_switcheroo.h>
Lukas Wunner [Mon, 12 Oct 2015 08:57:43 +0000 (10:57 +0200)]
drm/i915: Drop unnecessary #include <linux/vga_switcheroo.h>

Commit 599bbb9de0fe ("drm/i915: i915 cannot provide switcher services.")
removed all remaining vga_switcheroo symbols from intel_acpi.c but left
the include. Drop it.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Update DRIVER_DATE to 20151010
Daniel Vetter [Sat, 10 Oct 2015 11:35:42 +0000 (13:35 +0200)]
drm/i915: Update DRIVER_DATE to 20151010

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Partial revert of atomic watermark series
Matt Roper [Thu, 8 Oct 2015 22:28:25 +0000 (15:28 -0700)]
drm/i915: Partial revert of atomic watermark series

It's been reported that the atomic watermark series triggers some
regressions on SKL, which we haven't been able to track down yet.  Let's
temporarily revert these patches while we track down the root cause.

This commit squashes the reverts of:
  76305b1 drm/i915: Calculate watermark configuration during atomic check (v2)
  a4611e4 drm/i915: Don't set plane visible during HW readout if CRTC is off
  a28170f drm/i915: Calculate ILK-style watermarks during atomic check (v3)
  de4a9f8 drm/i915: Calculate pipe watermarks into CRTC state (v3)
  de165e0 drm/i915: Refactor ilk_update_wm (v3)

Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-October/077190.html
Cc: "Zanoni, Paulo R" <paulo.r.zanoni@intel.com>
Cc: "Vetter, Daniel" <daniel.vetter@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Early exit from semaphore_waits_for for execlist mode.
Tomas Elf [Thu, 8 Oct 2015 18:31:33 +0000 (19:31 +0100)]
drm/i915: Early exit from semaphore_waits_for for execlist mode.

When submitting semaphores in execlist mode the hang checker crashes in this
function because it is only runnable in ring submission mode. The reason this
is of particular interest to the TDR patch series is because we use semaphores
as a mean to induce hangs during testing (which is the recommended way to
induce hangs for gen8+). It's not clear how this is supposed to work in
execlist mode since:

1. This function requires a ring buffer.

2. Retrieving a ring buffer in execlist mode requires us to retrieve the
corresponding context, which we get from a request.

3. Retieving a request from the hang checker is not straight-forward since that
requires us to grab the struct_mutex in order to synchronize against the
request retirement thread.

4. Grabbing the struct_mutex from the hang checker is nothing that we will do
since that puts us at risk of deadlock since a hung thread might be holding the
struct_mutex already.

Therefore it's not obvious how we're supposed to deal with this. For now, we're
doing an early exit from this function, which avoids any kernel panic situation
when running our own internal TDR ULT.

* v2: (Chris Wilson)
Turned the execlist mode check into a ringbuffer NULL check to make it more
submission mode agnostic and less of a layering violation.

Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Remove wrong warning from i915_gem_context_clean
Tvrtko Ursulin [Thu, 8 Oct 2015 14:37:00 +0000 (15:37 +0100)]
drm/i915: Remove wrong warning from i915_gem_context_clean

commit e9f24d5fb7cf3628b195b18ff3ac4e37937ceeae
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date:   Mon Oct 5 13:26:36 2015 +0100

    drm/i915: Clean up associated VMAs on context destruction

Introduced a wrong assumption that all contexts have a ppgtt
instance. This is not true when full PPGTT is not active so
remove the WARN_ON_ONCE from the context cleanup code.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Determine the stolen memory base address on gen2
Ville Syrjälä [Thu, 8 Oct 2015 09:08:20 +0000 (12:08 +0300)]
drm/i915: Determine the stolen memory base address on gen2

There isn't an explicit stolen memory base register on gen2.
Some old comment in the i915 code suggests we should get it via
max_low_pfn_mapped, but that's clearly a bad idea on my MGM.

The e820 map in said machine looks like this:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000ce000-0x00000000000cffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000dc000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001f6effff] usable
[    0.000000] BIOS-e820: [mem 0x000000001f6f0000-0x000000001f6f7fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000001f6f8000-0x000000001f6fffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000001f700000-0x000000001fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffbfffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved

That makes max_low_pfn_mapped = 1f6f0000, so assuming our stolen memory
would start there would place it on top of some ACPI memory regions.
So not a good idea as already stated.

The 9MB region after the ACPI regions at 0x1f700000 however looks
promising given that the macine reports the stolen memory size to be
8MB. Looking at the PGTBL_CTL register, the GTT entries are at offset
0x1fee00000, and given that the GTT entries occupy 128KB, it looks like
the stolen memory could start at 0x1f700000 and the GTT entries would
occupy the last 128KB of the stolen memory.

After some more digging through chipset documentation, I've determined
the BIOS first allocates space for something called TSEG (something to
do with SMM) from the top of memory, and then it allocates the graphics
stolen memory below that. Accordind to the chipset documentation TSEG
has a fixed size of 1MB on 855. So that explains the top 1MB in the
e820 region. And it also confirms that the GTT entries are in fact at
the end of the the stolen memory region.

Derive the stolen memory base address on gen2 the same as the BIOS does
(TOM-TSEG_SIZE-stolen_size). There are a few differences between the
registers on various gen2 chipsets, so a few different codepaths are
required.

865G is again bit more special since it seems to support enough memory
to hit 4GB address space issues. This means the PCI allocations will
also affect the location of the stolen memory. Fortunately there
appears to be the TOUD register which may give us the correct answer
directly. But the chipset docs are a bit unclear, so I'm not 100%
sure that the graphics stolen memory is always the last thing the
BIOS steals. Someone would need to verify it on a real system.

I tested this on the my 830 and 855 machines, and so far everything
looks peachy.

v2: Rewrite to use the TOM-TSEG_SIZE-stolen_size and TOUD methods
v3: Fix TSEG size for 830
v4: Add missing 'else' (Chris)

Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: fix FBC buffer size checks
Paulo Zanoni [Thu, 1 Oct 2015 22:57:12 +0000 (19:57 -0300)]
drm/i915: fix FBC buffer size checks

According to my experiments (and later confirmation from the hardware
developers), the maximum sizes mentioned in the specification delimit
how far in the buffer the hardware tracking can go. And the hardware
calculates the size based on the plane address we provide - and the
provided plane address might not be the real x:0,y:0 point due to the
compute_page_offset() function.

On platforms that do the x/y offset adjustment trick it will be really
hard to reproduce a bug, but on the current SKL we can reproduce the
bug with igt/kms_frontbuffer_tracking/fbc-farfromfence. With this
patch, we'll go from "CRC assertion failure" to "FBC unexpectedly
disabled", which is still a failure on the test suite but is not a
perceived user bug - you will just not save as much power as you could
if FBC is disabled.

v2, rewrite patch after clarification from the Hadware guys:
  - Rename function so it's clear what the check is for.
  - Use the new intel_fbc_get_plane_source_sizes() function in order
    to get the proper sizes as seen by FBC.
v3:
  - Rebase after the s/sizes/size/ on the previous patch.
  - Adjust comment wording (Ville).
  - s/used_/effective_/ (Ville).

Testcase: igt/kms_frontbuffer_tracking/fbc-farfromfence (SKL)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: fix CFB size calculation
Paulo Zanoni [Thu, 1 Oct 2015 22:55:57 +0000 (19:55 -0300)]
drm/i915: fix CFB size calculation

We were considering the whole framebuffer height, but the spec says we
should only consider the active display height size. There were still
some unclear questions based on the spec, but the hardware guys
clarified them for us. According to them:

- CFB size = CFB stride * Number of lines FBC writes to CFB
- CFB stride = plane stride / compression limit
- Number of lines FBC writes to CFB = MIN(plane source height, maximum
  number of lines FBC writes to CFB)
- Plane source height =
  - pipe source height (PIPE_SRCSZ register) (before SKL)
  - plane size register height (PLANE_SIZE register) (SKL+)
- Maximum number of lines FBC writes to CFB =
  - plane source height (before HSW)
  - 2048 (HSW+)

For the plane source height, I could just have made our code do
I915_READ() in order to be more future proof, but since it's not cool
to do register reads I decided to just recalculate the values we use
when we actually write to those registers.

With this patch, depending on your machine configuration, a lot of the
kms_frontbuffer_tracking subtests that used to result in a SKIP due to
not enough stolen memory still start resulting in a PASS.

v2: Use the clipped src size instead of pipe_src_h (Ville).
v3: Use the appropriate information provided by the hardware guys.
v4: Bikesheds: s/sizes/size/, s/fb_cpp/cpp/ (Ville).
v5: - Don't use crtc->config->pipe_src_x for BDW- (Ville).
    - Fix the register name written in the comment.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: remove pre-atomic check from SKL update_primary_plane
Paulo Zanoni [Wed, 30 Sep 2015 20:05:43 +0000 (17:05 -0300)]
drm/i915: remove pre-atomic check from SKL update_primary_plane

The comment suggests the check was there for some non-fully-atomic
case, and I couldn't find a case where we wouldn't correctly
initialize plane_state, so remove the check.

Let's leave a WARN there just in case.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: don't allocate fbcon from stolen memory if it's too big
Paulo Zanoni [Wed, 23 Sep 2015 15:52:23 +0000 (12:52 -0300)]
drm/i915: don't allocate fbcon from stolen memory if it's too big

Technology has evolved and now we have eDP panels with 3200x1800
resolution. In the meantime, the BIOS guys didn't change the default
32mb for stolen memory. On top of that, we can't assume our users will
be able to increase the default stolen memory size to more than 32mb -
I'm not even sure all BIOSes allow that.

So just the fbcon buffer alone eats 22mb of my stolen memroy, and due
to the BDW/SKL restriction of not using the last 8mb of stolen memory,
all that's left for FBC is 2mb! Since fbcon is not the coolest feature
ever, I think it's better to save our precious stolen resource to FBC
and the other guys.

On the other hand, we really want to use as much stolen memory as
possible, since on some older systems the stolen memory may be a
considerable percentage of the total available memory.

This patch tries to achieve a little balance using a simple heuristic:
if the fbcon wants more than half of the available stolen memory,
don't use stolen memory in order to leave some for FBC and the other
features.

The long term plan should be to implement a way to set priorities for
stolen memory allocation and then evict low priority users when the
high priority ones need the memory. While we still don't have that,
let's try to make FBC usable with the simple solution.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agoRevert "drm/i915: Call encoder hotplug for init and resume cases"
Daniel Vetter [Thu, 8 Oct 2015 19:51:57 +0000 (21:51 +0200)]
Revert "drm/i915: Call encoder hotplug for init and resume cases"

This reverts commit 5d250b05918c002b63632c7db91c3c5f924c6a3b.

It results on a deadlock on platforms where we need to (at least
partially) re-init hpd interrupts from power domain code, since
->hot_plug might again grab a power well reference (to do edid/dp_aux
transactions. At least chv is affected.

Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: http://mid.gmane.org/20151008133548.GX26517@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
9 years agoRevert "drm/i915: Add hot_plug hook for hdmi encoder"
Daniel Vetter [Thu, 8 Oct 2015 19:50:57 +0000 (21:50 +0200)]
Revert "drm/i915: Add hot_plug hook for hdmi encoder"

This reverts commit 0b5e88dc25ee6c9040c0355e6e025dcbc9c8de92.

It completely breaks booting on at least bsw (and maybe more).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88081
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
9 years agodrm/i915: use error path
Sudip Mukherjee [Thu, 8 Oct 2015 13:57:59 +0000 (19:27 +0530)]
drm/i915: use error path

Use goto to handle the error path to avoid duplicating the same code. In
the error path intel_dig_port is the last one to be released as it was
the first one to be allocated and ideally the error path should be the
reverse of the execution path.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/irq: Fix misspelled word register in kernel-doc
Javier Martinez Canillas [Thu, 8 Oct 2015 07:57:49 +0000 (09:57 +0200)]
drm/i915/irq: Fix misspelled word register in kernel-doc

There is a typo in the function i915_handle_error()
kernel-doc and the word register is spelled wrongly.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915/irq: Fix kernel-doc warnings
Javier Martinez Canillas [Thu, 8 Oct 2015 07:54:44 +0000 (09:54 +0200)]
drm/i915/irq: Fix kernel-doc warnings

Add the dev parameter for the functions i915_enable_asle_pipestat() and
i915_reset_and_wakeup() to the kernel-doc to fix the following warnings:

.//drivers/gpu/drm/i915/i915_irq.c:586: warning: No description found for parameter 'dev'
.//drivers/gpu/drm/i915/i915_irq.c:2400: warning: No description found for parameter 'dev'

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Hook up ring workaround writes at context creation time on Gen6-7.
Francisco Jerez [Wed, 7 Oct 2015 11:44:02 +0000 (14:44 +0300)]
drm/i915: Hook up ring workaround writes at context creation time on Gen6-7.

intel_rcs_ctx_init() emits all workaround register writes on the list
to the ring, in addition to calling i915_gem_render_state_init().  The
workaround list is currently empty on Gen6-7 so this shouldn't cause
any functional changes.

Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
9 years agodrm/i915: Don't warn if the workaround list is empty.
Francisco Jerez [Wed, 7 Oct 2015 11:44:01 +0000 (14:44 +0300)]
drm/i915: Don't warn if the workaround list is empty.

It's not an error for the workaround list to be empty if no
workarounds are needed.  This will avoid spamming the logs
unnecessarily on Gen6 after the workaround list is hooked up on
pre-Gen8 hardware by the following commits.

Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>