Don Skidmore [Tue, 18 May 2010 16:00:13 +0000 (16:00 +0000)]
ixgbe: add support for active DA cables
This patch adds support of active DA cables. This is
renaming and adding some PHY type enumerations.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Tue, 18 May 2010 16:00:11 +0000 (16:00 +0000)]
ixgbe: dcb, do not tag tc_prio_control frames
The network stack indicate packets should not be DCB
tagged by setting the priority to TC_PRIO_CONTROL. One
usage for this is lldp frames which are not suppossed
to be tagged.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Tue, 18 May 2010 16:00:10 +0000 (16:00 +0000)]
ixgbe: fix ixgbe_tx_is_paused logic
The TFCS bits show the current XON state. Meaning that the
device is paused if these bits are 0. This fixes the logic
to work as it was intended.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Tue, 18 May 2010 16:00:08 +0000 (16:00 +0000)]
ixgbe: always enable vlan strip/insert when DCB is enabled
when DCB mode is on, we want the HW VLAN stripping to be always enabled.
Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Tue, 18 May 2010 16:00:07 +0000 (16:00 +0000)]
ixgbe: remove some redundant code in setting FCoE FIP filter
The ETQS setup for FIP out side the if..else is enough for the ETQS
setup for FIP, so remove redundant code.
Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Tue, 18 May 2010 16:00:05 +0000 (16:00 +0000)]
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
Make sure we point to the right offset of the fc_frame_header when
VLAN header exists and HW has VLAN stripping disabled.
Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 18 May 2010 16:00:03 +0000 (16:00 +0000)]
ixgbe: fix header len when unsplit packet overflows to data buffer
When in packet split mode, packet type is not recognized, and the packet is
larger than the header size, the 82599 overflows the packet into the data
area, but doesn't set the HDR_LEN field. We can safely assume the length
is the current header size. This fixes an obscure corner case that can be
triggered by non-ip packet headers or (more likely) by disabling the L2
packet recognition.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 18 May 2010 22:56:06 +0000 (15:56 -0700)]
ipv6: Never schedule DAD timer on dead address
This patch ensures that all places that schedule the DAD timer
look at the address state in a safe manner before scheduling the
timer. This ensures that we don't end up with pending timers
after deleting an address.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 18 May 2010 22:54:18 +0000 (15:54 -0700)]
ipv6: Use state_lock to protect ifa state
This patch makes use of the new state_lock to synchronise between
updates to the ifa state. This fixes the issue where a remotely
triggered address deletion (through DAD failure) coincides with a
local administrative address deletion, causing certain actions to
be performed twice incorrectly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 18 May 2010 22:36:06 +0000 (15:36 -0700)]
ipv6: Replace inet6_ifaddr->dead with state
This patch replaces the boolean dead flag on inet6_ifaddr with
a state enum. This allows us to roll back changes when deleting
an address according to whether DAD has completed or not.
This patch only adds the state field and does not change the logic.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: keep interrupts available when the ports are brought down
The PF driver needs to remain alert while its ports are down to service
requests or errors from virtual functions or FW so keep interrupts and
queues available when the ports are brought down. The change makes
open_device_map unnecessary so remove it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 18 May 2010 11:32:53 +0000 (11:32 +0000)]
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
Everytime the iSCSI ring finishes setup or shutdown, we need to return
the SPQ (slow path queue) credit to the bnx2x driver. Without this step,
the SPQ will eventually be full causing iSCSI to fail. This can happen
after 3 or 4 MTU changes for example.
Add code to wait for these slow path commands to complete in the RX ring
and return the SPQ credit to bnx2x.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Tue, 18 May 2010 21:03:10 +0000 (14:03 -0700)]
can: Fix SJA1000 command register writes on SMP systems
The SJA1000 command register is concurrently written in the rx-path to free
the receive buffer _and_ in the tx-path to start the transmission.
The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states:
"Between two commands at least one internal clock cycle is needed in
order to proceed. The internal clock is half of the external oscillator
frequency."
On SMP systems the current implementation leads to a write stall in the
tx-path, which can be solved by adding some general locking and some time
to settle the write_reg() operation for the command register.
Thanks to Klaus Hitschler for the original fix and detailed problem
description.
This patch applies on net-2.6 and (with some offsets) on net-next-2.6 .
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Tue, 18 May 2010 19:26:27 +0000 (12:26 -0700)]
bridge: fix build for CONFIG_SYSFS disabled
Fix build when CONFIG_SYSFS is not enabled:
net/bridge/br_if.c:136: error: 'struct net_bridge_port' has no member named 'sysfs_name'
Note: dev->name == sysfs_name except when change name is in
progress, and we are protected from that by RTNL mutex.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Bombe [Tue, 18 May 2010 06:12:46 +0000 (23:12 -0700)]
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
The SH SOHARD ARCNET cards are implemented using generic PLX Technology
PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified,
causing the driver to attach to any such bridge and likely crash the
system by attempting to initialize an unrelated device.
Fix by specifying subvendor and subdevice according to the values found
in the PCI-ID Repository at http://pci-ids.ucw.cz/ .
Cc: stable@kernel.org Signed-off-by: Andreas Bombe <aeb@debian.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 18 May 2010 06:08:21 +0000 (23:08 -0700)]
net: Remove unnecessary returns from void function()s
This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
If the user has a bad classification configuration, and gets a packet
that goes through too many steps. Chances are more packets will arrive,
and the message spew will overrun syslog because it is not rate limited.
And because it is not tagged with appropriate priority it can't not be screened.
Added the qdisc to the message to try and give some more context when
the message does arrive.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch encourage me to go look at all the messages in
the network scheduler and fix them. Many messages were missing
any severity level. Some serious ones that should never happen
were turned into WARN(), and the random noise messages that were
handled changed to pr_debug().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cause 'error cause' never be add the the ERROR chunk due to
some typo when check valid length in sctp_init_cause_fixed().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Reviewed-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Tue, 18 May 2010 05:50:19 +0000 (22:50 -0700)]
net: Add ndo_{set|get}_vf_port support for enic dynamic vnics
Add enic ndo_{set|get}_vf_port ops to support setting/getting
port-profile for enic dynamic devices. Enic dynamic devices are just like
normal enic eth devices except dynamic enics require an extra configuration
step to assign a port-profile identifier to the interface before the
interface is useable. Once a port-profile is assigned, link comes up on the
interface and is ready for I/O. The port-profile is used to configure the
network port assigned to the interface. The network port configuration
includes VLAN membership, QoS policies, and port security settings typical
of a data center network.
A dynamic enic initially has a zero-mac address. Before a port-profile is
assigned, a valid non-zero unicast mac address should be assign to the
dynamic enic interface.
Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Scott Feldman [Tue, 18 May 2010 05:49:55 +0000 (22:49 -0700)]
net: Add netlink support for virtual port management (was iovnl)
Add new netdev ops ndo_{set|get}_vf_port to allow setting of
port-profile on a netdev interface. Extends netlink socket RTM_SETLINK/
RTM_GETLINK with two new sub msgs called IFLA_VF_PORTS and IFLA_PORT_SELF
(added to end of IFLA_cmd list). These are both nested atrtibutes
using this layout:
These attributes are design to be set and get symmetrically. VF_PORTS
is a list of VF_PORTs, one for each VF, when dealing with an SR-IOV
device. PORT_SELF is for the PF of the SR-IOV device, in case it wants
to also have a port-profile, or for the case where the VF==PF, like in
enic patch 2/2 of this patch set.
A port-profile is used to configure/enable the external switch virtual port
backing the netdev interface, not to configure the host-facing side of the
netdev. A port-profile is an identifier known to the switch. How port-
profiles are installed on the switch or how available port-profiles are
made know to the host is outside the scope of this patch.
There are two types of port-profiles specs in the netlink msg. The first spec
is for 802.1Qbg (pre-)standard, VDP protocol. The second spec is for devices
that run a similar protocol as VDP but in firmware, thus hiding the protocol
details. In either case, the specs have much in common and makes sense to
define the netlink msg as the union of the two specs. For example, both specs
have a notition of associating/deassociating a port-profile. And both specs
require some information from the hypervisor manager, such as client port
instance ID.
The general flow is the port-profile is applied to a host netdev interface
using RTM_SETLINK, the receiver of the RTM_SETLINK msg communicates with the
switch, and the switch virtual port backing the host netdev interface is
configured/enabled based on the settings defined by the port-profile. What
those settings comprise, and how those settings are managed is again
outside the scope of this patch, since this patch only deals with the
first step in the flow.
Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Sun, 16 May 2010 21:15:14 +0000 (21:15 +0000)]
qeth: support the new OSA CHPID types OSX and OSM
The qeth driver is enabled to support the new OSA CHPID types OSX
and OSM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The member "clock" of struct "sja1000_platform_data" is documented as
"CAN bus oscillator frequency in Hz" but it's actually used as the CAN
clock frequency, which is half of it. To avoid further confusion, this
patch fixes it by renaming the member to "osc_freq". That way, also
non mainline users will notice the change. The platform code for the
relevant boards is updated accordingly. Furthermore, pre-defined
values are now used for the members "ocr" and "cdr".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 18 May 2010 05:35:36 +0000 (22:35 -0700)]
tcp: tcp_synack_options() fix
Commit 33ad798c924b4a (tcp: options clean up) introduced a problem
if MD5+SACK+timestamps were used in initial SYN message.
Some stacks (old linux for example) try to negotiate MD5+SACK+TSTAMP
sessions, but since 40 bytes of tcp options space are not enough to
store all the bits needed, we chose to disable timestamps in this case.
We send a SYN-ACK _without_ timestamp option, but socket has timestamps
enabled and all further outgoing messages contain a TS block, all with
the initial timestamp of the remote peer.
Fix is to really disable timestamps option for the whole session.
Reported-by: Bijay Singh <Bijay.Singh@guavus.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The duplicate address check code got broken in the conversion
to hlist (2.6.35). The earlier patch did not fix the case where
two addresses match same hash value. Use two exit paths,
rather than depending on state of loop variables (from macro).
Based on earlier fix by Shan Wei.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Tue, 18 May 2010 00:45:48 +0000 (17:45 -0700)]
dm9000: fix "BUG: spinlock recursion"
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in
dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and
net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by
renaming these functions to *_unlocked for the atomic context, and make the
original functions locking wrappers for use in the non-atomic context.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Fri, 14 May 2010 08:08:14 +0000 (08:08 +0000)]
net_sched: sch_hfsc: fix classification loops
When attaching filters to a class pointing to a class higher up in the
hierarchy, classification may enter an endless loop. Currently this is
prevented for filters that are already resolved, but not for filters
resolved at runtime.
Only allow filters to point downwards in the hierarchy, similar to what
CBQ does.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 16 May 2010 02:30:56 +0000 (02:30 +0000)]
r6040: fix link checking with switches
The current link checking logic only works for one port, which is not correct
for swiches were multiple ports can have different link status. As a result
we would only check for link status on port 1 of the switch. Move the calls
to mii_check_media in r6040_timer which will be polling a single PHY chip
correctly and assume link is up for switches.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Fri, 14 May 2010 04:27:36 +0000 (04:27 +0000)]
gianfar: Remove legacy PM callbacks
These callbacks were needed because dev_pm_ops support for OF
platform devices was in the powerpc tree, and the patch that
added dev_pm_ops for gianfar driver was in the netdev tree. Now
that netdev and powerpc trees have merged into Linus' tree, we
can remove the legacy hooks.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Several netem users use TBF for rate control. But every time the parameters
of TBF are changed it destroys the child qdisc, requiring reconfigation.
Better to just keep child qdisc and just notify it of changed limit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When stop device call netif_carrier_off() just after disabling TX queue to
avoid possibility of netdev watchdog warning and ->ndo_tx_timeout() invocation.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 18 May 2010 00:34:43 +0000 (17:34 -0700)]
bnx2: Use netif_carrier_off() to prevent timeout.
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>.
Using netif_carrier_off() is better than updating all the ->trans_start
on all the tx queues.
netif_carrier_off() needs to be called after bnx2_disable_int_sync()
to guarantee no race conditions with the serdes timers that can
modify the carrier state.
If the chip or phy is reset, carrier will turn back on when we get the
link interrupt. If there is no reset, we need to turn carrier back on
in bnx2_netif_start(). Again, the phy_lock prevents race conditions with
the serdes timers.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eddie Wai [Tue, 18 May 2010 00:32:56 +0000 (17:32 -0700)]
bnx2: Fix register printouts during NETEV_WATCHDOG.
Dump the correct MCP registers and add EMAC_RX_STATUS register during
NETDEV_WATCHDOG for debugging.
Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reset/set DEV_UP bit during allocation and deallocation of resources.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes memory leak in error path when memory allocation
for adapter data structures fails.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sonic Zhang [Mon, 10 May 2010 05:39:14 +0000 (05:39 +0000)]
netdev: bfin_mac: check for mii_bus platform data
If the platform data for the mii_bus is missing, gracefully error out
rather than deference NULL pointers.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Frysinger [Mon, 10 May 2010 05:39:13 +0000 (05:39 +0000)]
netdev: bfin_mac: handle timeouts with the MDIO registers gracefully
Have the low level MDIO functions pass back up timeout information so we
don't waste time polling them multiple times when there is a problem, and
so we don't let higher layers think the device is available when it isn't.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sonic Zhang [Mon, 10 May 2010 05:39:12 +0000 (05:39 +0000)]
netdev: bfin_mac: use promiscuous flag for promiscuous mode
Rather than using the Receive All Frames (RAF) bit to enable promiscuous
mode, use the Promiscuous (PR) bit. This lowers overhead at runtime as
we let the hardware process the packets that should actually be checked.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
netdev: bfin_mac: add support for wake-on-lan magic packets
Note that WOL works only in PM Suspend Standby Mode (Sleep Mode).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sonic Zhang [Mon, 10 May 2010 05:39:10 +0000 (05:39 +0000)]
netdev: bfin_mac: clear RXCKS if hardware generated checksum is not enabled
Otherwise we might be get a setting mismatch from a previous module or
bootloader and what the driver currently expects.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sonic Zhang [Mon, 10 May 2010 05:39:09 +0000 (05:39 +0000)]
netdev: bfin_mac: deduce Ethernet FCS from hardware IP payload checksum
IP checksum is based on 16-bit one's complement algorithm, so to deduce a
value from checksum is equal to add its complement.
Unfortunately, the Blackfin on-chip MAC checksum logic only works when the
IP packet has a header length of 20 bytes. This is true for most IPv4
packets, but not for IPv6 packets or IPv4 packets which use header options.
So only use the hardware checksum when appropriate.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Jon Kowal <jon.kowal@dspecialists.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sonic Zhang [Mon, 10 May 2010 05:39:08 +0000 (05:39 +0000)]
netdev: bfin_mac: invalid data cache only once for each new rx skb buffer
The skb buffer isn't actually used until we finish transferring and pass
it up to higher layers, so only invalidate the range once before we start
receiving actual data. This also avoids the problem with data invalidating
on Blackfin systems -- there is no invalidate-only, just invalidate+flush.
So when running in writeback mode, there is the small (but not uncommon)
possibility of the flush overwriting valid DMA-ed data from the cache.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Meerwald [Tue, 18 May 2010 00:20:50 +0000 (17:20 -0700)]
netdev: bfin_mac: handler RX status errors
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Barry Song [Tue, 18 May 2010 00:19:40 +0000 (17:19 -0700)]
netdev: bfin_mac: add support for IEEE 1588 PTP
Newer on-chip MAC peripherals support IEEE 1588 PTP in the hardware, so
extend the driver to support this functionality.
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 11 May 2010 23:19:48 +0000 (23:19 +0000)]
net: add a noref bit on skb dst
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Jones [Tue, 18 May 2010 00:18:28 +0000 (17:18 -0700)]
drivers/net/usb/asix.c: Fix unaligned accesses
Using this driver can cause unaligned accesses in the IP layer
This has been fixed by aligning the skb data correctly using the
spare room left over by the 4 byte header inserted between packets
by the device.
Signed-off-by: Neil Jones <NeilJay@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Brian King [Fri, 7 May 2010 08:56:08 +0000 (08:56 +0000)]
ibmveth: Add suspend/resume support
Adds support for resuming from suspend for IBM virtual ethernet devices.
We may have lost an interrupt over the suspend, so we just kick the
interrupt handler to process anything that is outstanding.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 11 May 2010 19:34:46 +0000 (19:34 +0000)]
qeth: new message if OLM limit is reached
z/OS may activate Optimized Latency Mode (OLM) for a connection
through an OSA Express3 adapter, which reduces the number of
allowed concurrent connections, if adapter is used in shared mode.
Create a meaningful message, if activation of an OSA-connection fails
due to an active OLM-connection on the shared OSA-adapter.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Tue, 11 May 2010 19:34:45 +0000 (19:34 +0000)]
qeth: exploit HW TX checksumming
OSA supports HW TX checksumming in layer 3 mode. Enable this
feature and remove software fallback used for TSO. Cleanup
checksum bits to indicate OSA can do checksumming only for
IPv4 TCP and UDP.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Sun, 9 May 2010 16:56:07 +0000 (16:56 +0000)]
sctp: delete active ICMP proto unreachable timer when free transport
transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 10 May 2010 04:51:02 +0000 (04:51 +0000)]
net: congestion notifications are not dropped packets
vlan/macvlan start_xmit() can inform caller of congestion with
NET_XMIT_CN return value. This doesnt mean packet was dropped.
Increment normal stat counters instead of tx_dropped.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 May 2010 07:36:33 +0000 (00:36 -0700)]
net: Introduce sk_route_nocaps
TCP-MD5 sessions have intermittent failures, when route cache is
invalidated. ip_queue_xmit() has to find a new route, calls
sk_setup_caps(sk, &rt->u.dst), destroying the
sk->sk_route_caps &= ~NETIF_F_GSO_MASK
that MD5 desperately try to make all over its way (from
tcp_transmit_skb() for example)
So we send few bad packets, and everything is fine when
tcp_transmit_skb() is called again for this socket.
Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a
socket field, sk_route_nocaps, containing bits to mask on sk_route_caps.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 May 2010 07:34:04 +0000 (00:34 -0700)]
tcp: fix MD5 (RFC2385) support
TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.
We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.
Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 May 2010 06:57:10 +0000 (23:57 -0700)]
net: Consistent skb timestamping
With RPS inclusion, skb timestamping is not consistent in RX path.
If netif_receive_skb() is used, its deferred after RPS dispatch.
If netif_rx() is used, its done before RPS dispatch.
This can give strange tcpdump timestamps results.
I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)
Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.
Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue
Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.
Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teras [Sun, 16 May 2010 06:49:26 +0000 (23:49 -0700)]
xfrm: fix policy unreferencing on larval drop
I mistakenly had the error path to use num_pols to decide how
many policies we need to drop (cruft from earlier patch set
version which did not handle socket policies right).
This is wrong since normally we do not keep explicit references
(instead we hold reference to the cache entry which holds references
to policies). drop_pols is set to num_pols if we are holding the
references, so use that. Otherwise we eventually BUG_ON inside
xfrm_policy_destroy due to premature policy deletion.
Signed-off-by: Timo Teras <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 6 May 2010 01:33:53 +0000 (01:33 +0000)]
net: adjust handle_macvlan to pass port struct to hook
Now there's null check here and also again in the hook. Looking at bridge bits
which are simmilar, port structure is rcu_dereferenced right away in
handle_bridge and passed to hook. Looks nicer.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Wed, 5 May 2010 00:27:06 +0000 (00:27 +0000)]
net: reserve ports for applications using fixed port numbers
(Dropped the infiniband part, because Tetsuo modified the related code,
I will send a separate patch for it once this is accepted.)
This patch introduces /proc/sys/net/ipv4/ip_local_reserved_ports which
allows users to reserve ports for third-party applications.
The reserved ports will not be used by automatic port assignments
(e.g. when calling connect() or bind() with port number 0). Explicit
port allocation behavior is unchanged.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: WANG Cong <amwang@redhat.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log