Benjamin Berg [Wed, 28 Sep 2016 12:11:58 +0000 (15:11 +0300)]
ath10k: allow setting coverage class
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.
In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 28 Sep 2016 12:11:57 +0000 (15:11 +0300)]
ath: export alpha2 helper
This will be helpful for drivers that can acquire
alpha2 regulatory codes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: add cc_wraparound type for QCA9888 and QCA9884
During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: fix return value in ath6kl_wmi_set_pvb_cmd
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Miaoqing Pan [Tue, 9 Aug 2016 07:02:27 +0000 (15:02 +0800)]
ath9k: disable RNG by default
ath9k RNG will dominates all the noise sources from the real HW
RNG, disable it by default. But we strongly recommand to enable
it if the system without HW RNG, especially on embedded systems.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Acked-by: Stephan Mueller <smueller@chronox.de> Acked-by: Stephan Mueller <smueller@chronox.de> Reviewed-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: Ignore SWBA event for a vif if its marked for no beacon
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ben Greear [Mon, 26 Sep 2016 18:56:26 +0000 (21:56 +0300)]
ath10k: support up to 64 vdevs
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: fix rfc1042 header retrieval in QCA4019 with eth decap mode
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Larry Finger [Wed, 21 Sep 2016 01:19:29 +0000 (21:19 -0400)]
rtl8xxxu: Stop log spam from each successful interrupt
As soon as debugging is turned on, the logs are filled with messages
reporting the interrupt status. As this quantity is usually zero, this
output is not needed. In fact, there will be a report if the status is
not zero, thus the debug line in question could probably be deleted.
Rather than taking that action, I have changed it to only be printed
when the newly added RTL8XXXU_DEBUG_INTERRUPT bit is set in the debug
mask.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove last_tx_page argument from the llt_init() function. The
rtl8xxxu_fileops structure contains the correct TX_TOTAL_PAGE_NUM
value for the device, and rtl8xxxu_auto_llt_table() doesn't need to
know the value in the first place.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cathy Luo [Tue, 20 Sep 2016 15:19:03 +0000 (20:49 +0530)]
mwifiex: fix race condition causing tx timeout
It's been observed that in a corner case mwifiex_usb_tx_complete()
gets called before we exit from mwifiex_usb_host_to_card() after
submitting the urb. 'data_sent' flag remains set in this case. It
blocks further Tx packets and triggers watchdog timeout.
The problem is fixed by setting data_sent and port_block flag at
correct place.
Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Shengzhen Li <szli@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In mwifiex_usb_tx_complete(), we are updating port->block_status first
and then freeing the skb attached to that URB. We may end up attaching
new skb to URB in a corner case and same will be freed. This results in
the kernel crash. The problem is solved by changing the sequence.
Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Shengzhen Li <szli@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 802.11 standard only has four valid auth type configurations of which
our firmware only supports two, ie. Open System and Shared Key. Simplify
the mapping falling back to automatic for other types specified by
user-space.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: fix out of bound access on clearing wowl wake indicator
Clearing the wowl wakeindicator happens with a rather odd
construction where the string "clear" is used to set the iovar
wowl_wakeind. This was implemented incorrectly as it caused an
out of bound access. Use an intermediate variable of correct
length and copy string in that. Problem was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When IPv6 address is to be cleared there is a possible out of
bound access. But also the clearing of the last entry and the
adjustment of total number of stored IPv6 addresses is not
updated. This patch fixes that bug. Bug was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in the function brcmf_bus_start() in the exception handling a
check is made to dermine whether ifp is null, though this is not
possible. Removing the unnessary check.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: remove worker from .ndo_set_mac_address() callback
As it turns out there is no need to use a worker for the callback
because it is not called from atomic context.
Reported-by: Dan Williams <dcbw@redhat.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: initialize variable in brcmf_sdiod_regrl()
In case of an error the variable returned is uninitialized. The caller
will probably check the error code before using it, but better assure
it is set to zero.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: rework pointer trickery in brcmf_proto_bcdc_query_dcmd()
The variable info is assigned to point to bcdc->msg[1], which is the
same as pointing to bcdc->buf. As that is what we want to access
make it clear by fixing the assignment. This also avoid out-of-bounds
errors from static analyzers are bcdc->msg[1] is not in the structure
definition.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
802.11d is not always supported by firmware anymore. Currently the
AP configuration of 11d will cause an abort if the ioctl set is
failing. This behavior is not correct and the error should be
ignored.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previously device used to start using IGTK key as Tx key as soon as it
gets downloaded in add_key(). This patch implements set_default_mgmt_key
handler. We will update Tx key ID in set_default_mgmt_key().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tony Lindgren [Sat, 17 Sep 2016 16:06:32 +0000 (09:06 -0700)]
wlcore: Fix config firmware loading issues
Booting multiple wl12xx and wl18xx devices using the same rootfs is
a pain. You currently have to symlink the right nvs file depending
on the wl12xx type.
For example, with wl1271-nvs.bin being a symlink to wl127x-nvs.bin
by default and trying to bring up a wl128x based device:
wlcore: ERROR nvs size is not as expected: 1113 != 912
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR firmware boot failed despite 3 retries
Note that wl18xx uses a separate config firmware wl18xx-conf.bin
that can be generated with tools using the following two git repos:
So let's not configure the nvs file for wl18xx as it's not needed
AFAIK. If it turns out that we also need the nvs file for wl18xx,
we can just add it to the config firmware data for wl18xx.
Let's fix the issue by using the chip specific config firmware
data, and make sure we produce understandable warnings if something
is missing.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Mon, 26 Sep 2016 11:10:31 +0000 (14:10 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2016-09-19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* added support for MU-MIMO sniffer
* added support for RRM by scan
* added support for packet injection
* migrate to devm memory allocation handling
* some fixes, mostly in DQA and new HW support
* other generic cleanups
Sara Sharon [Wed, 31 Aug 2016 16:03:01 +0000 (19:03 +0300)]
iwlwifi: mvm: set HCMD_NAME for PHY_DB as well
Currently it is logged as UNKNOWN.
Also, 0x6c seems to be the permanent ID for this command, remove
incorrect comment and uncomment the command from the commands
list.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ido Yariv [Tue, 23 Aug 2016 18:44:59 +0000 (14:44 -0400)]
iwlwifi: mvm: Add mem debugfs entry
In order to access cached/paged memory, there are a couple of firmware
commands (one for UMAC and one for LMAC) that let the host access memory
and registers indirectly. Since this is done by the firmware on behalf
of the host, even if memory is paged out or cached, the host will
retrieve the memory as the firmware sees it (paged out memory will get
paged in).
Export this mechanism via a debugfs entry for both read and write
access.
WARNING: This mechanism has no protections at all. Invalid addresses may
crash or hang the firmware. Writing to arbitrary memory also comes with
no guarantees.
Johannes Berg [Wed, 24 Aug 2016 08:05:40 +0000 (10:05 +0200)]
iwlwifi: mvm: move AP-specific code to right function
There's no need for the common MAC context function to have an
if on AP mode, the values can be overridden in the AP-specific
function later. Clean that up by adding the full command as a
new parameter to the AP-specific function, and doing it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get an unexpected Block Ack Request frame, the BAID from
the hardware will be invalid, and we'll pass it to mac80211 for
further handling (sending a delBA action frame.)
Add a comment explaining that, in case anyone looks in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement support for RRM by adding an option to configure the scan
dwell time and reporting scan start time and BSS detection time, and
Advertise support for these features.
Sara Sharon [Mon, 8 Aug 2016 10:07:01 +0000 (13:07 +0300)]
iwlwifi: mvm: support BAR in reorder buffer
On default queue we will not receive frame release notification,
but the BAR itself.
Upon receiving the BAR driver should look at the NSSN and adjust
window accordingly.
Fixes: b915c10174fb ("iwlwifi: mvm: add reorder buffer per queue") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Mon, 8 Aug 2016 08:51:24 +0000 (11:51 +0300)]
iwlwifi: mvm: fix DQA AP mode station assumption
There was recently a Full AP mode feature added where hostap adds
the station at auth stage, and not assoc.
However, when running with legacy hostapd, we get the auth response
before station was added, and tx_skb_non_sta fails to allocate
a queue, resulting in a complete failure of association.
Take care of this situation as well.
Add a warning when no valid queue is returned at all and make mvm
drop the packet instead of passing it on.
Refactor the function a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Haim Dreyfuss [Tue, 2 Aug 2016 12:28:23 +0000 (15:28 +0300)]
iwlwifi: check for valid ethernet address provided by OEM
In 9000 family products we added an option to let the OEM fuse the
mac address via registers. If these registers are zeroed we use the OTP
address instead. Make sure that the address provided by the OEM is valid
and, if not, fall back to the OTP address as well.
Fixes: commit 17c867bfe89b ("iwlwifi: add support for getting HW address from CSR") Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Thu, 4 Aug 2016 06:57:59 +0000 (08:57 +0200)]
iwlwifi: mvm: compare full command ID
When comparing command IDs, the group should be taken
into account so the same command/notification from a
different group doesn't trigger anything unexpected.
Fix this by comparing to the wide ID.
Colin Ian King [Fri, 16 Sep 2016 09:37:31 +0000 (10:37 +0100)]
mwifiex: fix null pointer deference when adapter is null
If adapter is null the error exit path in mwifiex_shutdown_sw is
to down the semaphore sem and print some debug via mwifiex_dbg.
However, passing a NULL adapter to mwifiex_dbg causes a null
pointer deference when accessing adapter->dev. This fix checks
for a null adapter at the start of the function and to exit
without the need to up the semaphore and we also skip the debug
to avoid the null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bob Copeland [Wed, 14 Sep 2016 12:42:36 +0000 (08:42 -0400)]
mwifiex: fix error handling in mwifiex_create_custom_regdomain
smatch reports:
sta_cmdresp.c:1053 mwifiex_create_custom_regdomain() warn: possible memory leak of 'regd'
Indeed, mwifiex_create_custom_regdomain() returns NULL in the
case that channel is missing in the TLV without freeing regd.
Moreover, some other error paths in this function return ERR_PTR
values which are assigned without checking to the regd field in
the mwifiex_adapter struct. The latter is only null-checked where
used.
Fix by freeing regd in the error path, and only update
priv->adapter->regd if the returned pointer is valid.
Cc: Amitkumar Karwar <akarwar@marvell.com> Cc: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Sat, 17 Sep 2016 15:10:33 +0000 (18:10 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2016-09-15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support
* general cleanups and improvements
samples/bpf: add comprehensive ipip, ipip6, ip6ip6 test
the test creates 3 namespaces with veth connected via bridge.
First two namespaces simulate two different hosts with the same
IPv4 and IPv6 addresses configured on the tunnel interface and they
communicate with outside world via standard tunnels.
Third namespace creates collect_md tunnel that is driven by BPF
program which selects different remote host (either first or
second namespace) based on tcp dest port number while tcp dst
ip is the same.
This scenario is rough approximation of load balancer use case.
The tests check both traditional tunnel configuration and collect_md mode.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve tunnels allow IPIP6 and IP6IP6 tunnels
to operate in 'collect metadata' mode.
Unlike ipv4 code here it's possible to reuse ip6_tnl_xmit() function
for both collect_md and traditional tunnels.
bpf_skb_[gs]et_tunnel_key() helpers and ovs (in the future) are the users.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Thomas Graf <tgraf@suug.ch> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve tunnels allow IPIP tunnels to
operate in 'collect metadata' mode.
bpf_skb_[gs]et_tunnel_key() helpers can make use of it right away.
ovs can use it as well in the future (once appropriate ovs-vport
abstractions and user apis are added).
Note that just like in other tunnels we cannot cache the dst,
since tunnel_info metadata can be different for every packet.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Thomas Graf <tgraf@suug.ch> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Thu, 15 Sep 2016 20:23:26 +0000 (22:23 +0200)]
l2tp: constify net_device_ops structures
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
Julia Lawall [Thu, 15 Sep 2016 20:23:25 +0000 (22:23 +0200)]
dwc_eth_qos: constify net_device_ops structures
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct net_device_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct net_device_ops i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
21623 1316 40 22979 59c3
drivers/net/ethernet/synopsys/dwc_eth_qos.o
and after the change it is:
text data bss dec hex filename
22199 724 40 22963 59b3
drivers/net/ethernet/synopsys/dwc_eth_qos.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Thu, 15 Sep 2016 20:23:24 +0000 (22:23 +0200)]
hisilicon: constify net_device_ops structures
Check for net_device_ops structures that are only stored in the netdev_ops
field of a net_device structure. This field is declared const, so
net_device_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
Eric Dumazet [Thu, 15 Sep 2016 16:33:02 +0000 (09:33 -0700)]
tcp: prepare skbs for better sack shifting
With large BDP TCP flows and lossy networks, it is very important
to keep a low number of skbs in the write queue.
RACK and SACK processing can perform a linear scan of it.
We should avoid putting any payload in skb->head, so that SACK
shifting can be done if needed.
With this patch, we allow to pack ~0.5 MB per skb instead of
the 64KB initially cooked at tcp_sendmsg() time.
This gives a reduction of number of skbs in write queue by eight.
tcp_rack_detect_loss() likes this.
We still allow payload in skb->head for first skb put in the queue,
to not impact RPC workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Sep 2016 13:53:29 +0000 (09:53 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2016-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.9
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Sep 2016 13:51:48 +0000 (09:51 -0400)]
Merge branch 'mlx5e-order-0'
Tariq Toukan says:
====================
mlx5e Order-0 pages for Striding RQ
In this series, we refactor our Striding RQ receive-flow to always use
fragmented WQEs (Work Queue Elements) using order-0 pages, omitting the
flow that allocates and splits high-order pages which would fragment
and deplete high-order pages in the system.
The first patch gives a slight degradation, but opens the opportunity
to using a simple page-cache mechanism of a fair size.
The page-cache, implemented in patch 3, not only closes the performance
gap but even gives a gain.
In patch 2 we re-organize the code to better manage the calls for
alloc/de-alloc pages in the RX flow.
Series generated against net-next commit: bed806cb266e "Merge branch 'mlxsw-ethtool'"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Implement RX mapped page cache for page recycle
Instead of reallocating and mapping pages for RX data-path,
recycle already used pages in a per ring cache.
Performance tests:
The following results were measured on a freshly booted system,
giving optimal baseline performance, as high-order pages are yet to
be fragmented and depleted.
We ran pktgen single-stream benchmarks, with iptables-raw-drop:
Single stride, 64 bytes:
* 4,739,057 - baseline
* 4,749,550 - order0 no cache
* 4,786,899 - order0 with cache
1% gain
Larger packets, no page cross, 1024 bytes:
* 3,982,361 - baseline
* 3,845,682 - order0 no cache
* 4,127,852 - order0 with cache
3.7% gain
Larger packets, every 3rd packet crosses a page, 1500 bytes:
* 3,731,189 - baseline
* 3,579,414 - order0 no cache
* 3,931,708 - order0 with cache
5.4% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manage the allocation and deallocation of mapped RX pages only
through dedicated API functions.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Single flow order-0 pages for Striding RQ
To improve the memory consumption scheme, we omit the flow that
demands and splits high-order pages in Striding RQ, and stay
with a single Striding RQ flow that uses order-0 pages.
Moving to fragmented memory allows the use of larger MPWQEs,
which reduces the number of UMR posts and filler CQEs.
Moving to a single flow allows several optimizations that improve
performance, especially in production servers where we would
anyway fallback to order-0 allocations:
- inline functions that were called via function pointers.
- improve the UMR post process.
This patch alone is expected to give a slight performance reduction.
However, the new memory scheme gives the possibility to use a page-cache
of a fair size, that doesn't inflate the memory footprint, which will
dramatically fix the reduction and even give a performance gain.
Performance tests:
The following results were measured on a freshly booted system,
giving optimal baseline performance, as high-order pages are yet to
be fragmented and depleted.
We ran pktgen single-stream benchmarks, with iptables-raw-drop:
Single stride, 64 bytes:
* 4,739,057 - baseline
* 4,749,550 - this patch
no reduction
Larger packets, no page cross, 1024 bytes:
* 3,982,361 - baseline
* 3,845,682 - this patch
3.5% reduction
Larger packets, every 3rd packet crosses a page, 1500 bytes:
* 3,731,189 - baseline
* 3,579,414 - this patch
4% reduction
Fixes: 461017cb006a ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)") Fixes: bc77b240b3c5 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 17 Sep 2016 06:26:01 +0000 (07:26 +0100)]
rxrpc: Make IPv6 support conditional on CONFIG_IPV6
Add CONFIG_AF_RXRPC_IPV6 and make the IPv6 support code conditional on it.
This is then made conditional on CONFIG_IPV6.
Without this, the following can be seen:
net/built-in.o: In function `rxrpc_init_peer':
>> peer_object.c:(.text+0x18c3c8): undefined reference to `ip6_route_output_flags'
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Sep 2016 08:31:56 +0000 (04:31 -0400)]
Merge branch 'QCA8K'
John Crispin says:
====================
net-next: dsa: add QCA8K support
This series is based on the AR8xxx series posted by Matthieu Olivari in may
2015. The following changes were made since then
* fixed the nitpicks from the previous review
* updated to latest API
* turned it into an mdio device
* added callbacks for fdb, bridge offloading, stp, eee, port status
* fixed several minor issues to the port setup and arp learning
* changed the namespacing as this driver to qca8k
The driver has so far only been tested on qca8337/N. It should work on other QCA
switches such as the qca8327 with minor changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Thu, 15 Sep 2016 14:26:41 +0000 (16:26 +0200)]
net-next: dsa: add new driver for qca8xxx family
This patch contains initial support for the QCA8337 switch. It
will detect a QCA8337 switch, if present and declared in the DT.
Each port will be represented through a standalone net_device interface,
as for other DSA switches. CPU can communicate with any of the ports by
setting an IP@ on ethN interface. Most of the extra callbacks of the DSA
subsystem are already supported, such as bridge offloading, stp, fdb.
Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Thu, 15 Sep 2016 14:26:40 +0000 (16:26 +0200)]
net-next: dsa: add Qualcomm tag RX/TX handler
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Thu, 15 Sep 2016 14:26:39 +0000 (16:26 +0200)]
Documentation: devicetree: add qca8k binding
Add device-tree binding for ar8xxx switch families.
Cc: devicetree@vger.kernel.org Signed-off-by: John Crispin <john@phrozen.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: b53: Remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/bcm_sf2.c:963:19: warning:
symbol 'bcm_sf2_io_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 9f5afeae5152 ("tcp: use an RB tree for ooo receive queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Yuchung Cheng <ycheng@google.com> Cc: Yaogong Wang <wygivan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Sep 2016 06:23:06 +0000 (02:23 -0400)]
Merge branch 'mediatek-reset-flow'
Sean Wang says:
====================
mediatek: add enhancement into the existing reset flow
Current driver only resets DMA used by descriptor rings which
can't guarantee it can recover all various kinds of fatal
errors, so the patch
1) tries to reset the underlying hardware resource from scratch on
Mediatek SoC required for ethernet running.
2) refactors code in order to the reusability of existing code.
3) considers handling for race condition between the reset flow and
callbacks registered into core driver called about hardware accessing.
4) introduces power domain usage to hardware setup which leads to have
cleanly and completely restore to the state as the initial.
Changes since v1:
- fix the build error with module built causing undefined symbol for
pinctrl_bind_pins, so using pinctrl_select_state instead accomplishes
the pin mux setup during the reset process.
====================
Reviewed-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log