David S. Miller [Wed, 4 May 2016 17:32:29 +0000 (13:32 -0400)]
Merge branch 'tunnel-features-and-gso-partial'
Alexander Duyck says:
====================
Fix Tunnel features and enable GSO partial for several drivers
This patch series is meant to allow us to get the best performance possible
for Mellanox ConnectX-3/4 and Broadcom NetXtreme-C/E adapters in terms of
VXLAN and GRE tunnels.
The first 3 patches address issues I found in regards to GSO_PARTIAL and
TSO_MANGLEID.
The next 4 patches go through and enable GSO_PARTIAL for VXLAN tunnels that
have an outer checksum enabled, and then enable IPv6 support where I can.
One outstanding issue is that I wasn't able to get offloads working with
outer IPv6 headers on mlx4. However that wasn't a feature that was enabled
before so it isn't technically a regression, however I believe Engineers
from Mellanox said they would look into it since they thought it should be
supported.
The last patch enables GSO_PARTIAL for VXLAN and GRE tunnels on the bnxt
driver. One piece of feedback I received on the patch was that the
hardware has globally set IPv6 UDP tunnels to always have the checksum
field computed. I plan to work with Broadcom to get that addressed so that
we only populate the checksum field if it was requested by the network
stack.
v2: Rebased patches off of latest changes to the mlx4/mlx5 drivers.
Added bnxt driver patch as I received feedback on the RFC.
v3: Moved 2 patches into series for net as they were generic fixes.
Added patch to disable GSO partial if frame is less than 2x size of MSS
There are outstanding issues as called out above that need to be
addressed, however they were present before these patches so it isn't
as if they introduce a regression. In addition gains can be easily
seen so there should be no issue with applying the driver patches while
the IPv6 mlx4_en and bnxt issues are being researched.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:55 +0000 (09:38 -0700)]
bnxt: Add support for segmentation of tunnels with outer checksums
This patch assumes that the bnxt hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP and GRE headers.
I have been told by Michael Chan that this is working. Though this might
be somewhat redundant for IPv6 as they are forcing the checksum to be
computed for all IPv6 frames that are offloaded. A follow-up patch may be
necessary in order to fix this as it is essentially mangling the outer IPv6
headers to add a checksum where none was requested.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:49 +0000 (09:38 -0700)]
net/mlx5e: Fix IPv6 tunnel checksum offload
The mlx5 driver exposes support for TSO6 but not IPv6 csum for hardware
encapsulated tunnels. This leads to issues as it triggers warnings in
skb_checksum_help as it ends up being called as we report supporting the
segmentation but not the checksumming for IPv6 frames.
This patch corrects that and drops 2 features that don't actually need to
be supported in hw_enc_features since they are Rx features and don't
actually impact anything by being present in hw_enc_features.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:43 +0000 (09:38 -0700)]
net/mlx5e: Add support for UDP tunnel segmentation with outer checksum offload
This patch assumes that the mlx5 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:37 +0000 (09:38 -0700)]
net/mlx4_en: Add support for inner IPv6 checksum offloads and TSO
>From what I can tell the ConnectX-3 will support an inner IPv6 checksum and
segmentation offload, however it cannot support outer IPv6 headers. This
assumption is based on the fact that I could see the checksum being
offloaded for inner header on IPv4 tunnels, but not on IPv6 tunnels.
For this reason I am adding the feature to the hw_enc_features and adding
an extra check to the features_check call that will disable GSO and
checksum offload in the case that the encapsulated frame has an outer IP
version of that is not 4. The check in mlx4_en_features_check could be
removed if at some point in the future a fix is found that allows the
hardware to offload segmentation/checksum on tunnels with an outer IPv6
header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:30 +0000 (09:38 -0700)]
net/mlx4_en: Add support for UDP tunnel segmentation with outer checksum offload
This patch assumes that the mlx4 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:24 +0000 (09:38 -0700)]
net: Fix netdev_fix_features so that TSO_MANGLEID is only available with TSO
This change makes it so that we will strip the TSO_MANGLEID bit if TSO is
not present. This way we will also handle ECN correctly of TSO is not
present.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:18 +0000 (09:38 -0700)]
gso: Only allow GSO_PARTIAL if we can checksum the inner protocol
This patch addresses a possible issue that can occur if we get into any odd
corner cases where we support TSO for a given protocol but not the checksum
or scatter-gather offload. There are few drivers floating around that
setup their tunnels this way and by enforcing the checksum piece we can
avoid mangling any frames.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:38:12 +0000 (09:38 -0700)]
gso: Do not perform partial GSO if number of partial segments is 1 or less
In the event that the number of partial segments is equal to 1 we don't
really need to perform partial segmentation offload. As such we should
skip multiplying the MSS and instead just clear the partial_segs value
since it will not provide any gain to advertise the frame as being GSO when
it is a single frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Tue, 3 May 2016 13:00:21 +0000 (15:00 +0200)]
gre: change gre_parse_header to return the header length
It's easier for gre_parse_header to return the header length instead of
filing it into a parameter. That way, the callers that don't care about the
header length can just check whether the returned value is lower than zero.
In gre_err, the tunnel header must not be pulled. See commit b7f8fe251e46
("gre: do not pull header in ICMP error processing") for details.
This patch reduces the conflict between the mentioned commit and commit 95f5c64c3c13 ("gre: Move utility functions to common headers").
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 3 May 2016 04:49:25 +0000 (21:49 -0700)]
tcp: guarantee forward progress in tcp_sendmsg()
Under high rx pressure, it is possible tcp_sendmsg() never has a
chance to allocate an skb and loop forever as sk_flush_backlog()
would always return true.
Fix this by calling sk_flush_backlog() only if one skb had been
allocated and filled before last backlog check.
Fixes: d41a69f1d390 ("tcp: make tcp_sendmsg() aware of socket backlog") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Some straggler bug fixes:
1) Batman-adv DAT must consider VLAN IDs when choosing candidate
nodes, from Antonio Quartulli.
2) Fix botched reference counting of vlan objects and neigh nodes in
batman-adv, from Sven Eckelmann.
3) netem can crash when it sees GSO packets, the fix is to segment
then upon ->enqueue. Fix from Neil Horman with help from Eric
Dumazet.
4) Fix VXLAN dependencies in mlx5 driver Kconfig, from Matthew
Finlay.
5) Handle VXLAN ops outside of rcu lock, via a workqueue, in mlx5,
since it can sleep. Fix also from Matthew Finlay.
6) Check mdiobus_scan() return values properly in pxa168_eth and macb
drivers. From Sergei Shtylyov.
7) If the netdevice doesn't support checksumming, disable
segmentation. From Alexandery Duyck.
8) Fix races between RDS tcp accept and sending, from Sowmini
Varadhan.
9) In macb driver, probe MDIO bus before we register the netdev,
otherwise we can try to open the device before it is really ready
for that. Fix from Florian Fainelli.
10) Netlink attribute size for ILA "tunnels" not calculated properly,
fix from Nicolas Dichtel"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6/ila: fix nlsize calculation for lwtunnel
net: macb: Probe MDIO bus before registering netdev
RDS: TCP: Synchronize accept() and connect() paths on t_conn_lock.
RDS:TCP: Synchronize rds_tcp_accept_one with rds_send_xmit when resetting t_sock
vxlan: Add checksum check to the features check function
net: Disable segmentation if checksumming is not supported
net: mvneta: Remove superfluous SMP function call
macb: fix mdiobus_scan() error check
pxa168_eth: fix mdiobus_scan() error check
net/mlx5e: Use workqueue for vxlan ops
net/mlx5e: Implement a mlx5e workqueue
net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue
net/mlx5: Unmap only the relevant IO memory mapping
netem: Segment GSO packets on enqueue
batman-adv: Fix reference counting of hardif_neigh_node object for neigh_node
batman-adv: Fix reference counting of vlan object for tt_local_entry
batman-adv: B.A.T.M.A.N V - make sure iface is reactivated upon NETDEV_UP event
batman-adv: fix DAT candidate selection (must use vid)
Linus Torvalds [Tue, 3 May 2016 21:23:58 +0000 (14:23 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Fix a regression and update the MAINTAINERS entry for fuse"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: update mailing list in MAINTAINERS
fuse: Fix return value from fuse_get_user_pages()
Nicolas Dichtel [Tue, 3 May 2016 07:58:27 +0000 (09:58 +0200)]
ipv6/ila: fix nlsize calculation for lwtunnel
The handler 'ila_fill_encap_info' adds one attribute: ILA_ATTR_LOCATOR.
Fixes: 65d7ab8de582 ("net: Identifier Locator Addressing module") CC: Tom Herbert <tom@herbertland.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Tue, 3 May 2016 04:40:07 +0000 (21:40 -0700)]
ipv6: add new struct ipcm6_cookie
In the sendmsg function of UDP, raw, ICMP and l2tp sockets, we use local
variables like hlimits, tclass, opt and dontfrag and pass them to corresponding
functions like ip6_make_skb, ip6_append_data and xxx_push_pending_frames.
This is not a good practice and makes it hard to add new parameters.
This fix introduces a new struct ipcm6_cookie similar to ipcm_cookie in
ipv4 and include the above mentioned variables. And we only pass the
pointer to this structure to corresponding functions. This makes it easier
to add new parameters in the future and makes the function cleaner.
Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: macb: Probe MDIO bus before registering netdev
The current sequence makes us register for a network device prior to
registering and probing the MDIO bus which could lead to some unwanted
consequences, like a thread of execution calling into ndo_open before
register_netdev() returns, while the MDIO bus is not ready yet.
Rework the sequence to register for the MDIO bus, and therefore attach
to a PHY prior to calling register_netdev(), which implies reworking the
error path a bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 May 2016 20:03:45 +0000 (16:03 -0400)]
Merge branch 'rds-fixes'
Sowmini Varadhan says:
====================
RDS: TCP: sychronization during connection startup
This patch series ensures that the passive (accept) side of the
TCP connection used for RDS-TCP is correctly synchronized with
any concurrent active (connect) attempts for a given pair of peers.
Patch 1 in the series makes sure that the t_sock in struct
rds_tcp_connection is only reset after any threads in rds_tcp_xmit
have completed (otherwise a null-ptr deref may be encountered).
Patch 2 synchronizes rds_tcp_accept_one() with the rds_tcp*connect()
path.
v2: review comments from Santosh Shilimkar, other spelling corrections
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS: TCP: Synchronize accept() and connect() paths on t_conn_lock.
An arbitration scheme for duelling SYNs is implemented as part of
commit 241b271952eb ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()") which ensures that both nodes
involved will arrive at the same arbitration decision. However, this
needs to be synchronized with an outgoing SYN to be generated by
rds_tcp_conn_connect(). This commit achieves the synchronization
through the t_conn_lock mutex in struct rds_tcp_connection.
The rds_conn_state is checked in rds_tcp_conn_connect() after acquiring
the t_conn_lock mutex. A SYN is sent out only if the RDS connection is
not already UP (an UP would indicate that rds_tcp_accept_one() has
completed 3WH, so no SYN needs to be generated).
Similarly, the rds_conn_state is checked in rds_tcp_accept_one() after
acquiring the t_conn_lock mutex. The only acceptable states (to
allow continuation of the arbitration logic) are UP (i.e., outgoing SYN
was SYN-ACKed by peer after it sent us the SYN) or CONNECTING (we sent
outgoing SYN before we saw incoming SYN).
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RDS:TCP: Synchronize rds_tcp_accept_one with rds_send_xmit when resetting t_sock
There is a race condition between rds_send_xmit -> rds_tcp_xmit
and the code that deals with resolution of duelling syns added
by commit 241b271952eb ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()").
Specifically, we may end up derefencing a null pointer in rds_send_xmit
if we have the interleaving sequence:
rds_tcp_accept_one rds_send_xmit
The race condition can be avoided without adding the overhead of
additional locking in the xmit path: have rds_tcp_accept_one wait
for rds_tcp_xmit threads to complete before resetting callbacks.
The synchronization can be done in the same manner as rds_conn_shutdown().
First set the rds_conn_state to something other than RDS_CONN_UP
(so that new threads cannot get into rds_tcp_xmit()), then wait for
RDS_IN_XMIT to be cleared in the conn->c_flags indicating that any
threads in rds_tcp_xmit are done.
Fixes: 241b271952eb ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()") Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 2 May 2016 17:56:27 +0000 (10:56 -0700)]
net: add __sock_wfree() helper
Hosts sending lot of ACK packets exhibit high sock_wfree() cost
because of cache line miss to test SOCK_USE_WRITE_QUEUE
We could move this flag close to sk_wmem_alloc but it is better
to perform the atomic_sub_and_test() on a clean cache line,
as it avoid one extra bus transaction.
skb_orphan_partial() can also have a fast track for packets that either
are TCP acks, or already went through another skb_orphan_partial()
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 May 2016 20:00:55 +0000 (16:00 -0400)]
Merge branch 'tunnel-csum-and-sg-offloads'
Alexander Duyck says:
====================
Fixes for tunnel checksum and segmentation offloads
This patch series is a subset of patches I had submitted for net-next. I
plan to drop these two patches from the v3 of "Fix Tunnel features and
enable GSO partial for several drivers" and I am instead submitting them
for net since these are truly fixes and likely will need to be backported
to stable branches.
This series addresses 2 specific issues. The first is that we could
request TSO on a v4 inner header while not supporting checksum offload of
the outer IPv6 header. The second is that we could request an IPv6 inner
checksum offload without validating that we could actually support an inner
IPv6 checksum offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:25:16 +0000 (09:25 -0700)]
vxlan: Add checksum check to the features check function
We need to perform an additional check on the inner headers to determine if
we can offload the checksum for them. Previously this check didn't occur
so we would generate an invalid frame in the case of an IPv6 header
encapsulated inside of an IPv4 tunnel. To fix this I added a secondary
check to vxlan_features_check so that we can verify that we can offload the
inner checksum.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 May 2016 16:25:10 +0000 (09:25 -0700)]
net: Disable segmentation if checksumming is not supported
In the case of the mlx4 and mlx5 driver they do not support IPv6 checksum
offload for tunnels. With this being the case we should disable GSO in
addition to the checksum offload features when we find that a device cannot
perform a checksum on a given packet type.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 2 May 2016 15:58:47 +0000 (11:58 -0400)]
tipc: redesign connection-level flow control
There are two flow control mechanisms in TIPC; one at link level that
handles network congestion, burst control, and retransmission, and one
at connection level which' only remaining task is to prevent overflow
in the receiving socket buffer. In TIPC, the latter task has to be
solved end-to-end because messages can not be thrown away once they
have been accepted and delivered upwards from the link layer, i.e, we
can never permit the receive buffer to overflow.
Currently, this algorithm is message based. A counter in the receiving
socket keeps track of number of consumed messages, and sends a dedicated
acknowledge message back to the sender for each 256 consumed message.
A counter at the sending end keeps track of the sent, not yet
acknowledged messages, and blocks the sender if this number ever reaches
512 unacknowledged messages. When the missing acknowledge arrives, the
socket is then woken up for renewed transmission. This works well for
keeping the message flow running, as it almost never happens that a
sender socket is blocked this way.
A problem with the current mechanism is that it potentially is very
memory consuming. Since we don't distinguish between small and large
messages, we have to dimension the socket receive buffer according
to a worst-case of both. I.e., the window size must be chosen large
enough to sustain a reasonable throughput even for the smallest
messages, while we must still consider a scenario where all messages
are of maximum size. Hence, the current fix window size of 512 messages
and a maximum message size of 66k results in a receive buffer of 66 MB
when truesize(66k) = 131k is taken into account. It is possible to do
much better.
This commit introduces an algorithm where we instead use 1024-byte
blocks as base unit. This unit, always rounded upwards from the
actual message size, is used when we advertise windows as well as when
we count and acknowledge transmitted data. The advertised window is
based on the configured receive buffer size in such a way that even
the worst-case truesize/msgsize ratio always is covered. Since the
smallest possible message size (from a flow control viewpoint) now is
1024 bytes, we can safely assume this ratio to be less than four, which
is the value we are now using.
This way, we have been able to reduce the default receive buffer size
from 66 MB to 2 MB with maintained performance.
In order to keep this solution backwards compatible, we introduce a
new capability bit in the discovery protocol, and use this throughout
the message sending/reception path to always select the right unit.
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 2 May 2016 15:58:46 +0000 (11:58 -0400)]
tipc: propagate peer node capabilities to socket layer
During neighbor discovery, nodes advertise their capabilities as a bit
map in a dedicated 16-bit field in the discovery message header. This
bit map has so far only be stored in the node structure on the peer
nodes, but we now see the need to keep a copy even in the socket
structure.
This commit adds this functionality.
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Mon, 2 May 2016 15:58:45 +0000 (11:58 -0400)]
tipc: re-enable compensation for socket receive buffer double counting
In the refactoring commit d570d86497ee ("tipc: enqueue arrived buffers
in socket in separate function") we did by accident replace the test
if (sk->sk_backlog.len == 0)
atomic_set(&tsk->dupl_rcvcnt, 0);
with
if (sk->sk_backlog.len)
atomic_set(&tsk->dupl_rcvcnt, 0);
This effectively disables the compensation we have for the double
receive buffer accounting that occurs temporarily when buffers are
moved from the backlog to the socket receive queue. Until now, this
has gone unnoticed because of the large receive buffer limits we are
applying, but becomes indispensable when we reduce this buffer limit
later in this series.
We now fix this by inverting the mentioned condition.
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3b9d6da67e11 ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: netdev@vger.kernel.org Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to remove the init/exit callbacks from the dwmac-
socfpga driver and instead use standard PM callbacks. Doing this
will also allow us to cleanup the driver.
Eventually the init/exit callbacks will be deprecated and removed
from all drivers dwmac-* except for dwmac-generic. Drivers will be
refactored to use standard PM and remove callbacks.
This patch set should not change the behavior of the driver itself,
it only moves code around. The only exception to this is patch
number 4 which restores the resume callback behavior which was
changed in the "net: stmmac: socfpga: Remove re-registration of
reset controller" patch. I belive calling phy_resume() only
from the resume callback and not probe is the right thing to do.
Changes from v1:
- Rebase on net-next
One heads-up here:
The first patch changes the prototype of a couple of
functions used in Alexandre's "add Ethernet glue logic for
stm32 chip" patch [1] and will cause build failures for
dwmac-stm32.c if not fixed up!
If Alexandre's patch set is applied first I will gladly
rebase my patch set to account for his driver as well.
stmmac: dwmac-socfpga: kill init() and rename setup() to set_phy_mode()
Remove old init callback which now contains only a call to
socfpga_dwmac_setup(). Also rename socfpga_dwmac_setup() to indicate
what the function really does.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: dwmac-socfpga: keep a copy of stmmac_rst in driver priv data
The dwmac-socfpga driver needs to control the reset usually managed
by the core driver to set the PHY mode. Take a copy of the reset
handle from core priv data so it can be used by the driver later.
This also allow us to move reset handling into socfpga_dwmac_setup()
where the code that needs it is located.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: dwmac-socfpga: add PM ops and resume function
Implement the needed PM callbacks in the driver instead of
relying on the init/exit hooks in stmmac_platform. This gives
the driver more flexibility in how the code is organized.
Eventually the init/exit callbacks will be deprecated in favor
of the standard PM callbacks and driver remove function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: let remove/resume/suspend functions take device pointer
Change stmmac_remove/resume/suspend to take a device pointer so
they can be used directly by drivers that doesn't need to perform
anything device specific.
This lets us remove the PCI pm functions and later simplifiy the
platform drivers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 30 Apr 2016 22:47:36 +0000 (01:47 +0300)]
macb: fix mdiobus_scan() error check
Now mdiobus_scan() returns ERR_PTR(-ENODEV) instead of NULL if the PHY
device ID was read as all ones. As this was not an error before, this
value should be filtered out now in this driver.
Fixes: b74766a0a0fe ("phylib: don't return NULL from get_phy_device()") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 30 Apr 2016 20:35:11 +0000 (23:35 +0300)]
pxa168_eth: fix mdiobus_scan() error check
Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check for both, not only for NULL, otherwise a crash is
imminent...
Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 3 May 2016 18:06:01 +0000 (11:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Fixes for the HID subsystem:
- regression fix for Wacom driver; commit introduced in 4.6-rc1
mistakenly removed line that should be kept. Fix by Ping Cheng
- two device-specific quirks, by Ping Cheng and Nazar Mokrynskyi"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: add missed stylus_in_proximity line back
HID: Fix boot delay for Creative SB Omni Surround 5.1 with quirk
HID: wacom: Add support for DTK-1651
Linus Torvalds [Tue, 3 May 2016 17:58:29 +0000 (10:58 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small bug fix for the imx6qp CAN clk definition that was causing
failures and division by zeros in the kernel on those devices"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx6q: fix typo in CAN clock definition
David S. Miller [Tue, 3 May 2016 17:37:27 +0000 (13:37 -0400)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes for 4.6-rc
This small series provides some bug fixes for mlx5 driver.
A small bug fix for iounmap of a null pointer, which dumps a warning on some archs.
One patch to fix the VXLAN/MLX5_EN dependency issue reported by Arnd.
Two patches to fix the scheduling while atomic issue for ndo_add/del_vxlan_port
NDOs. The first will add an internal mlx5e workqueue and the second will
delegate vxlan ports add/del requests to that workqueue.
Note: ('net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue') is only needed for net
and not net-next as the issue was globally fixed for all device drivers by: b7aade15485a ('vxlan: break dependency with netdev drivers') in net-next.
Applied on top: f27337e16f2d ('ip_tunnel: fix preempt warning in ip tunnel creation/updating')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Finlay [Sun, 1 May 2016 19:59:57 +0000 (22:59 +0300)]
net/mlx5e: Use workqueue for vxlan ops
The vxlan add/delete port NDOs are called under rcu lock.
The current mlx5e implementation can potentially block in these
calls, which is not allowed. Move to using the mlx5e workqueue
to handle these NDOs.
Fixes: b3f63c3d5e2c ('net/mlx5e: Add netdev support for VXLAN tunneling') Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Finlay [Sun, 1 May 2016 19:59:56 +0000 (22:59 +0300)]
net/mlx5e: Implement a mlx5e workqueue
Implement a mlx5e workqueue to handle all mlx5e specific tasks. Move
all tasks currently using the system workqueue to the new workqueue.
This is in preparation for vxlan using the mlx5e workqueue in order to
schedule port add/remove operations.
Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Finlay [Sun, 1 May 2016 19:59:55 +0000 (22:59 +0300)]
net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue
When MLX5_EN=y MLX5_CORE=y and VXLAN=m there is a linker error for
vxlan_get_rx_port() due to the fact that VXLAN is a module. Change Kconfig
to select VXLAN when MLX5_CORE=y. When MLX5_CORE=m there is no dependency
on the value of VXLAN.
Fixes: b3f63c3d5e2c ('net/mlx5e: Add netdev support for VXLAN tunneling') Signed-off-by: Matthew Finlay <matt@mellanox.com> Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Sun, 1 May 2016 19:59:54 +0000 (22:59 +0300)]
net/mlx5: Unmap only the relevant IO memory mapping
When freeing UAR the driver tries to unmap uar->map and uar->bf_map
which are mutually exclusive thus always unmapping a NULL pointer.
Make sure we only call iounmap() once, for the actual mapping.
Fixes: 0ba422410bbf ('net/mlx5: Fix global UAR mapping') Signed-off-by: Gal Pressman <galp@mellanox.com> Reported-by: Doron Tsur <doront@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The xgene_cle_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 1 May 2016 23:47:26 +0000 (16:47 -0700)]
fq_codel: add batch ability to fq_codel_drop()
In presence of inelastic flows and stress, we can call
fq_codel_drop() for every packet entering fq_codel qdisc.
fq_codel_drop() is quite expensive, as it does a linear scan
of 4 KB of memory to find a fat flow.
Once found, it drops the oldest packet of this flow.
Instead of dropping a single packet, try to drop 50% of the backlog
of this fat flow, with a configurable limit of 64 packets per round.
TCA_FQ_CODEL_DROP_BATCH_SIZE is the new attribute to make this
limit configurable.
With this strategy the 4 KB search is amortized to a single cache line
per drop [1], so fq_codel_drop() no longer appears at the top of kernel
profile in presence of few inelastic flows.
[1] Assuming a 64byte cache line, and 1024 buckets
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dave Taht <dave.taht@gmail.com> Cc: Jonathan Morton <chromatix99@gmail.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Dave Taht Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Tested-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ping Cheng [Tue, 3 May 2016 04:17:34 +0000 (21:17 -0700)]
HID: wacom: add missed stylus_in_proximity line back
Commit 7e12978 ("HID: wacom: break out wacom_intuos_get_tool_type") by accident
removed stylus_in_proximity flag for Intuos series while shuffling the code
around.
Fix that by reintroducing that flag setting in wacom_intuos_inout(), where
it originally was.
Neil Horman [Mon, 2 May 2016 16:20:15 +0000 (12:20 -0400)]
netem: Segment GSO packets on enqueue
This was recently reported to me, and reproduced on the latest net kernel,
when attempting to run netperf from a host that had a netem qdisc attached
to the egress interface:
The problem occurs because netem is not prepared to handle GSO packets (as it
uses skb_checksum_help in its enqueue path, which cannot manipulate these
frames).
The solution I think is to simply segment the skb in a simmilar fashion to the
way we do in __dev_queue_xmit (via validate_xmit_skb), with some minor changes.
When we decide to corrupt an skb, if the frame is GSO, we segment it, corrupt
the first segment, and enqueue the remaining ones.
tested successfully by myself on the latest net kernel, to which this applies
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Jamal Hadi Salim <jhs@mojatatu.com> CC: "David S. Miller" <davem@davemloft.net> CC: netem@lists.linux-foundation.org CC: eric.dumazet@gmail.com CC: stephen@networkplumber.org Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 May 2016 04:17:38 +0000 (00:17 -0400)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
In this small batch of patches you have:
- a fix for our Distributed ARP Table that makes sure that the input
provided to the hash function during a query is the same as the one
provided during an insert (so to prevent false negatives), by Antonio
Quartulli
- a fix for our new protocol implementation B.A.T.M.A.N. V that ensures
that a hard interface is properly re-activated when it is brought down
and then up again, by Antonio Quartulli
- two fixes respectively to the reference counting of the tt_local_entry
and neigh_node objects, by Sven Eckelmann. Such bug is rather severe
as it would prevent the netdev objects references by batman-adv from
being released after shutdown.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- trans_timeout is incremented when tx queue timed out (tx watchdog).
- tx_maxrate is set via sysfs
Moving tx_maxrate to read-mostly part shrinks the struct by 64 bytes.
While at it, also move trans_timeout (it is out-of-place in the
'write-mostly' part).
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 May 2016 02:27:06 +0000 (22:27 -0400)]
Merge branch 'bridge-per-vlan-stats'
Nikolay Aleksandrov says:
====================
bridge: per-vlan stats
This set adds support for bridge per-vlan statistics.
In order to be able to dump statistics for many vlans we need a way to
continue dumping after reaching maximum size, thus patches 01 and 02 extend
the new stats API with a per-device extended link stats attribute and
callback which can save its local state and continue where it left off
afterwards. I considered using the already existing "fill_xstats" callback
but it gets confusing since we need to separate the linkinfo dump from the
new stats api dump and adding a flag/argument to do that just looks messy.
I don't think the rtnl_link_ops size is an issue, so adding these seemed
like the cleaner approach.
Patches 03 and 04 add the stats support and netlink dump support
respectively. The stats accounting is controlled via a bridge option which
is default off, thus the performance impact is kept minimal.
I've tested this set with both old and modified iproute2, kmemleak on and
some traffic stress tests while adding/removing vlans and ports.
v3:
- drop the RCU pvid patch and remove one pointer fetch as requested
- make stats accounting optional with default to off, the option is in the
same cache line as vlan_proto and vlan_enabled, so it is already fetched
before the fast path check thus the performance impact is minimal, this
also allows us to avoid one vlan lookup and return early when using pvid
- rebased and retested
v2:
- Improve the error checking, rename lidx to prividx and save the current
idx user instead of restricting it to one in patch 01
- squash patch 02 into 01 and remove the restriction
- add callback descriptions, improve the size calculation and change the
xstats message structure to have an embedding level per rtnl link type
so we can avoid one call to get the link type (and thus filter on it)
and also each link type can now have any number of private attributes
inside
- fix a problem where the vlan stats are not dumped if the bridge has 0
vlans on it but has vlans on the ports, add bridge link type private
attributes and also add paddings for future extensions to avoid at least
a few netlink attributes and improve struct alignment
- drop the is_skb_forwardable argument constifying patch as it's not
needed anymore, but it's a nice cleanup which I'll send separately
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new LINK_XSTATS_TYPE_BRIDGE attribute and implement the
RTM_GETSTATS callbacks for IFLA_STATS_LINK_XSTATS (fill_linkxstats and
get_linkxstats_size) in order to export the per-vlan stats.
The paddings were added because soon these fields will be needed for
per-port per-vlan stats (or something else if someone beats me to it) so
avoiding at least a few more netlink attributes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per-VLAN Tx/Rx statistics. Every global vlan context gets
allocated a per-cpu stats which is then set in each per-port vlan context
for quick access. The br_allowed_ingress() common function is used to
account for Rx packets and the br_handle_vlan() common function is used
to account for Tx packets. Stats accounting is performed only if the
bridge-wide vlan_stats_enabled option is set either via sysfs or netlink.
A struct hole between vlan_enabled and vlan_proto is used for the new
option so it is in the same cache line. Currently it is binary (on/off)
but it is intentionally restricted to exactly 0 and 1 since other values
will be used in the future for different purposes (e.g. per-port stats).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: rtnetlink: add linkxstats callbacks and attribute
Add callbacks to calculate the size and fill link extended statistics
which can be split into multiple messages and are dumped via the new
rtnl stats API (RTM_GETSTATS) with the IFLA_STATS_LINK_XSTATS attribute.
Also add that attribute to the idx mask check since it is expected to
be able to save state and resume dumping (e.g. future bridge per-vlan
stats will be dumped via this attribute and callbacks).
Each link type should nest its private attributes under the per-link type
attribute. This allows to have any number of separated private attributes
and to avoid one call to get the dev link type.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: rtnetlink: allow rtnl_fill_statsinfo to save private state counter
The new prividx argument allows the current dumping device to save a
private state counter which would enable it to continue dumping from
where it left off. And the idxattr is used to save the current idx user
so multiple prividx using attributes can be requested at the same time
as suggested by Roopa Prabhu.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 2 May 2016 23:23:32 +0000 (19:23 -0400)]
Merge branch 'ipv6-tunnel-cleanups'
Tom Herbert says:
====================
net: Cleanup IPv6 ip tunnels
The IPv6 tunnel code is very different from IPv4 code. There is a lot
of redundancy with the IPv4 code, particularly in the GRE tunneling.
This patch set cleans up the tunnel code to make the IPv6 code look
more like the IPv4 code and use common functions between the two
stacks where possible.
This work should make it easier to maintain and extend the IPv6 ip
tunnels.
Items in this patch set:
- Cleanup IPv6 tunnel receive path (ip6_tnl_rcv). Includes using
gro_cells and exporting ip6_tnl_rcv so the ip6_gre can call it
- Move GRE functions to common header file (tx functions) or
gre_demux.c (rx functions like gre_parse_header)
- Call common GRE functions from IPv6 GRE
- Create ip6_tnl_xmit (to be like ip_tunnel_xmit)
Tested:
Ran super_netperf tests for TCP_RR and TCP_STREAM for:
- IPv4 over gre, gretap, gre6, gre6tap
- IPv6 over gre, gretap, gre6, gre6tap
- ipip
- ip6ip6
- ipip/gue
- IPv6 over gre/gue
- IPv4 over gre/gue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sat, 30 Apr 2016 00:12:20 +0000 (17:12 -0700)]
ipv6: Generic tunnel cleanup
A few generic changes to generalize tunnels in IPv6:
- Export ip6_tnl_change_mtu so that it can be called by ip6_gre
- Add tun_hlen to ip6_tnl structure.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sat, 30 Apr 2016 00:12:19 +0000 (17:12 -0700)]
gre: Create common functions for transmit
Create common functions for both IPv4 and IPv6 GRE in transmit. These
are put into gre.h.
Common functions are for:
- GRE checksum calculation. Move gre_checksum to gre.h.
- Building a GRE header. Move GRE build_header and rename
gre_build_header.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sat, 30 Apr 2016 00:12:18 +0000 (17:12 -0700)]
ipv6: Create ip6_tnl_xmit
This patch renames ip6_tnl_xmit2 to ip6_tnl_xmit and exports it. Other
users like GRE will be able to call this. The original ip6_tnl_xmit
function is renamed to ip6_tnl_start_xmit (this is an ndo_start_xmit
function).
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sat, 30 Apr 2016 00:12:17 +0000 (17:12 -0700)]
gre6: Cleanup GREv6 receive path, call common GRE functions
- Create gre_rcv function. This calls gre_parse_header and ip6gre_rcv.
- Call ip6_tnl_rcv. Doing this and using gre_parse_header eliminates
most of the code in ip6gre_rcv.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sat, 30 Apr 2016 00:12:16 +0000 (17:12 -0700)]
gre: Move utility functions to common headers
Several of the GRE functions defined in net/ipv4/ip_gre.c are usable
for IPv6 GRE implementation (that is they are protocol agnostic).
These include:
- GRE flag handling functions are move to gre.h
- GRE build_header is moved to gre.h and renamed gre_build_header
- parse_gre_header is moved to gre_demux.c and renamed gre_parse_header
- iptunnel_pull_header is taken out of gre_parse_header. This is now
done by caller. The header length is returned from gre_parse_header
in an int* argument.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sat, 30 Apr 2016 00:12:15 +0000 (17:12 -0700)]
ipv6: Cleanup IPv6 tunnel receive path
Some basic changes to make IPv6 tunnel receive path look more like
IPv4 path:
- Make ip6_tnl_rcv non-static so that GREv6 and others can call it
- Make ip6_tnl_rcv look like ip_tunnel_rcv
- Switch to gro_cells_receive
- Make ip6_tnl_rcv non-static and export it
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 2 May 2016 21:02:26 +0000 (17:02 -0400)]
Merge branch 'tcp-preempt'
Eric Dumazet says:
====================
net: make TCP preemptible
Most of TCP stack assumed it was running from BH handler.
This is great for most things, as TCP behavior is very sensitive
to scheduling artifacts.
However, the prequeue and backlog processing are problematic,
as they need to be flushed with BH being blocked.
To cope with modern needs, TCP sockets have big sk_rcvbuf values,
in the order of 16 MB, and soon 32 MB.
This means that backlog can hold thousands of packets, and things
like TCP coalescing or collapsing on this amount of packets can
lead to insane latency spikes, since BH are blocked for too long.
It is time to make UDP/TCP stacks preemptible.
Note that fast path still runs from BH handler.
v2: Added "tcp: make tcp_sendmsg() aware of socket backlog"
to reduce latency problems of large sends.
v3: Fixed a typo in tcp_cdg.c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:53 +0000 (14:16 -0700)]
tcp: make tcp_sendmsg() aware of socket backlog
Large sendmsg()/write() hold socket lock for the duration of the call,
unless sk->sk_sndbuf limit is hit. This is bad because incoming packets
are parked into socket backlog for a long time.
Critical decisions like fast retransmit might be delayed.
Receivers have to maintain a big out of order queue with additional cpu
overhead, and also possible stalls in TX once windows are full.
Bidirectional flows are particularly hurt since the backlog can become
quite big if the copy from user space triggers IO (page faults)
Some applications learnt to use sendmsg() (or sendmmsg()) with small
chunks to avoid this issue.
Kernel should know better, right ?
Add a generic sk_flush_backlog() helper and use it right
before a new skb is allocated. Typically we put 64KB of payload
per skb (unless MSG_EOR is requested) and checking socket backlog
every 64KB gives good results.
As a matter of fact, tests with TSO/GSO disabled give very nice
results, as we manage to keep a small write queue and smaller
perceived rtt.
Note that sk_flush_backlog() maintains socket ownership,
so is not equivalent to a {release_sock(sk); lock_sock(sk);},
to ensure implicit atomicity rules that sendmsg() was
giving to (possibly buggy) applications.
In this simple implementation, I chose to not call tcp_release_cb(),
but we might consider this later.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexei Starovoitov <ast@fb.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:52 +0000 (14:16 -0700)]
net: do not block BH while processing socket backlog
Socket backlog processing is a major latency source.
With current TCP socket sk_rcvbuf limits, I have sampled __release_sock()
holding cpu for more than 5 ms, and packets being dropped by the NIC
once ring buffer is filled.
All users are now ready to be called from process context,
we can unblock BH and let interrupts be serviced faster.
cond_resched_softirq() could be removed, as it has no more user.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:51 +0000 (14:16 -0700)]
sctp: prepare for socket backlog behavior change
sctp_inq_push() will soon be called without BH being blocked
when generic socket code flushes the socket backlog.
It is very possible SCTP can be converted to not rely on BH,
but this needs to be done by SCTP experts.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:50 +0000 (14:16 -0700)]
udp: prepare for non BH masking at backlog processing
UDP uses the generic socket backlog code, and this will soon
be changed to not disable BH when protocol is called back.
We need to use appropriate SNMP accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:49 +0000 (14:16 -0700)]
dccp: do not assume DCCP code is non preemptible
DCCP uses the generic backlog code, and this will soon
be changed to not disable BH when protocol is called back.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:48 +0000 (14:16 -0700)]
tcp: do not block bh during prequeue processing
AFAIK, nothing in current TCP stack absolutely wants BH
being disabled once socket is owned by a thread running in
process context.
As mentioned in my prior patch ("tcp: give prequeue mode some care"),
processing a batch of packets might take time, better not block BH
at all.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Apr 2016 21:16:47 +0000 (14:16 -0700)]
tcp: do not assume TCP code is non preemptible
We want to to make TCP stack preemptible, as draining prequeue
and backlog queues can take lot of time.
Many SNMP updates were assuming that BH (and preemption) was disabled.
Need to convert some __NET_INC_STATS() calls to NET_INC_STATS()
and some __TCP_INC_STATS() to TCP_INC_STATS()
Before using this_cpu_ptr(net->ipv4.tcp_sk) in tcp_v4_send_reset()
and tcp_v4_send_ack(), we add an explicit preempt disabled section.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: xgene: Get channel number from device binding
This patch gets ethernet to CPU channel (prefetch buffer number) from
the newly added 'channel' property, thus decoupling Linux driver from
resource management.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 2 May 2016 19:46:42 +0000 (12:46 -0700)]
Minimal fix-up of bad hashing behavior of hash_64()
This is a fairly minimal fixup to the horribly bad behavior of hash_64()
with certain input patterns.
In particular, because the multiplicative value used for the 64-bit hash
was intentionally bit-sparse (so that the multiply could be done with
shifts and adds on architectures without hardware multipliers), some
bits did not get spread out very much. In particular, certain fairly
common bit ranges in the input (roughly bits 12-20: commonly with the
most information in them when you hash things like byte offsets in files
or memory that have block factors that mean that the low bits are often
zero) would not necessarily show up much in the result.
There's a bigger patch-series brewing to fix up things more completely,
but this is the fairly minimal fix for the 64-bit hashing problem. It
simply picks a much better constant multiplier, spreading the bits out a
lot better.
NOTE! For 32-bit architectures, the bad old hash_64() remains the same
for now, since 64-bit multiplies are expensive. The bigger hashing
cleanup will replace the 32-bit case with something better.
The new constants were picked by George Spelvin who wrote that bigger
cleanup series. I just picked out the constants and part of the comment
from that series.
Cc: stable@vger.kernel.org Cc: George Spelvin <linux@horizon.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 2 May 2016 19:22:51 +0000 (12:22 -0700)]
Merge tag 'md/4.6-rc6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"This update includes several trival fixes. The only important one is
to fix MD bio merge, which has big performance impact"
* tag 'md/4.6-rc6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid5: delete unnecessary warnning
MD: make bio mergeable
md/raid0: remove empty line printk from dump_zones
md/raid0: fix uninitialized variable bug
Linus Torvalds [Mon, 2 May 2016 16:54:22 +0000 (09:54 -0700)]
Merge tag 'gpio-v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are some late but important fixes for the v4.6 kernel series.
ACPI and RCAR, so two driver fixes (PM related) and a self-evident
string lookup fix for ACPI GPIOs:
- A serious ACPI fix targeted for stable: lookup strings were being
free'd.
- Revert two patches from the RCAR driver"
* tag 'gpio-v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib-acpi: Duplicate con_id string when adding it to the crs lookup list
Revert "gpio: rcar: Fine-grained Runtime PM support"
Revert "gpio: rcar: Add Runtime PM handling for interrupts"
1) MODULE_FIRMWARE firmware string not correct for iwlwifi 8000 chips,
from Sara Sharon.
2) Fix SKB size checks in batman-adv stack on receive, from Sven
Eckelmann.
3) Leak fix on mac80211 interface add error paths, from Johannes Berg.
4) Cannot invoke napi_disable() with BH disabled in myri10ge driver,
fix from Stanislaw Gruszka.
5) Fix sign extension problem when computing feature masks in
net_gso_ok(), from Marcelo Ricardo Leitner.
6) lan78xx driver doesn't count packets and packet lengths in its
statistics properly, fix from Woojung Huh.
7) Fix the buffer allocation sizes in pegasus USB driver, from Petko
Manolov.
8) Fix refcount overflows in bpf, from Alexei Starovoitov.
9) Unified dst cache handling introduced a preempt warning in
ip_tunnel, fix by resetting rather then setting the cached route.
From Paolo Abeni.
10) Listener hash collision test fix in soreuseport, from Craig Gallak
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
gre: do not pull header in ICMP error processing
net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case
tipc: only process unicast on intended node
cxgb3: fix out of bounds read
net/smscx5xx: use the device tree for mac address
soreuseport: Fix TCP listener hash collision
net: l2tp: fix reversed udp6 checksum flags
ip_tunnel: fix preempt warning in ip tunnel creation/updating
samples/bpf: fix trace_output example
bpf: fix check_map_func_compatibility logic
bpf: fix refcnt overflow
drivers: net: cpsw: use of_phy_connect() in fixed-link case
dt: cpsw: phy-handle, phy_id, and fixed-link are mutually exclusive
drivers: net: cpsw: don't ignore phy-mode if phy-handle is used
drivers: net: cpsw: fix segfault in case of bad phy-handle
drivers: net: cpsw: fix parsing of phy-handle DT property in dual_emac config
MAINTAINERS: net: Change maintainer for GRETH 10/100/1G Ethernet MAC device driver
gre: reject GUE and FOU in collect metadata mode
pegasus: fixes reported packet length
pegasus: fixes URB buffer allocation size;
...
3) Allow proper auto-loading of VIO devices, from John Paul Adrian
Glaubitz.
4) Recognize Sonoma cpus, from Khalid Aziz.
5) Fix bootup regressions caused by syscall trace fixes made recently.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix bootup regressions on some Kconfig combinations.
sparc64: recognize and support Sonoma CPU type
sparc: Implement and wire up vio_hotplug for vio.
sparc: Implement and wire up modalias_show for vio.
sparc/pci: Refactor dev_archdata initialization into pci_init_dev_archdata
sparc/defconfigs: Remove CONFIG_IPV6_PRIVACY
sparc: Write up preadv2/pwritev2 syscalls.
sparc/PCI: Fix for panic while enabling SR-IOV
iptunnel_pull_header expects that IP header was already pulled; with this
expectation, it pulls the tunnel header. This is not true in gre_err.
Furthermore, ipv4_update_pmtu and ipv4_redirect expect that skb->data points
to the IP header.
We cannot pull the tunnel header in this path. It's just a matter of not
calling iptunnel_pull_header - we don't need any of its effects.
Fixes: bda7bb463436 ("gre: Allow multiple protocol listener for gre protocol.") Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds the driver support for following selftests:
1. Register test
2. Memory test
3. Clock test
4. Interrupt test
5. Internal loopback test
Patch (1) adds the qed driver infrastructure for selftests. Patches (2) and
(3) add qede driver support for ethtool selftests.
Please consider applying this series to "net-next".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the qede ethtool support for the following tests:
- interrupt test
- memory test
- register test
- clock test
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality and APIs needed for selftests.
It adds the ability to configure the link-mode which is required for the
implementation of loopback tests. It adds the APIs for clock test,
register test, interrupt test and memory test.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log