Lidong Zhong [Wed, 13 May 2015 06:04:10 +0000 (14:04 +0800)]
dm raid1: keep issuing IO after leg failure
Currently if there is a leg failure, the bio will be put into the hold
list until userspace does a remove/replace on the leg. Doing so in a
cluster config (clvmd) is problematic because there may be a temporary
path failure that results in cluster raid1 remove/replace. Such
recovery takes a long time due to a full resync.
Update dm-raid1 to optionally ignore these failures so bios continue
being issued without interrupton. To enable this feature userspace
must pass "keep_log" when creating the dm-raid1 device.
Signed-off-by: Lidong Zhong <lzhong@suse.com> Tested-by: Liuhua Wang <lwang@suse.com> Acked-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Reviewed-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- ensure maximum device limit in superblock
- rename DMPF_* (print flags) to CTR_FLAG_* (constructor flags)
and their respective struct raid_set member
- use strcasecmp() in raid10_format_to_md_layout() as in the constructor
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Reviewed-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Reviewed-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Mike Snitzer [Thu, 14 May 2015 15:28:37 +0000 (11:28 -0400)]
dm thin: cleanup schedule_zero() to read more logically
The overwrite has only ever about optimizing away the need to zero a
block if the entire block was being overwritten. As such it is only
relevant when zeroing is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Joe Thornber <ejt@redhat.com>
Mike Snitzer [Tue, 28 Apr 2015 15:50:29 +0000 (11:50 -0400)]
dm: factor out a common cleanup_mapped_device()
Introduce a single common method for cleaning up a DM device's
mapped_device. No functional change, just eliminates duplication of
delicate mapped_device cleanup code.
Mike Snitzer [Wed, 29 Apr 2015 16:07:12 +0000 (12:07 -0400)]
dm: cleanup methods that requeue requests
More often than not a request that is requeued _is_ mapped (meaning the
clone request is allocated and clone->q is initialized). Rename
dm_requeue_unmapped_original_request() to avoid potential confusion due
to function name containing "unmapped".
Also, remove dm_requeue_unmapped_request() since callers can easily call
the dm_requeue_original_request() directly.
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Mike Snitzer [Mon, 27 Apr 2015 20:37:50 +0000 (16:37 -0400)]
dm: do not allocate any mempools for blk-mq request-based DM
Do not allocate the io_pool mempool for blk-mq request-based DM
(DM_TYPE_MQ_REQUEST_BASED) in dm_alloc_rq_mempools().
Also refine __bind_mempools() to have more precise awareness of which
mempools each type of DM device uses -- avoids mempool churn when
reloading DM tables (particularly for DM_TYPE_REQUEST_BASED).
Joe Thornber [Fri, 29 May 2015 13:52:51 +0000 (14:52 +0100)]
dm: fix casting bug in dm_merge_bvec()
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org # 3.19+
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c205983 ("dm table: train hybrid target type detection to select blk-mq if appropriate") Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Mike Snitzer [Thu, 28 May 2015 19:12:52 +0000 (15:12 -0400)]
dm: fix false warning in free_rq_clone() for unmapped requests
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request") Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Mike Snitzer [Wed, 27 May 2015 19:25:27 +0000 (15:25 -0400)]
dm: requeue from blk-mq dm_mq_queue_rq() using BLK_MQ_RQ_QUEUE_BUSY
Use BLK_MQ_RQ_QUEUE_BUSY to requeue a blk-mq request directly from the
DM blk-mq device's .queue_rq. This cleans up the previous convoluted
handling of request requeueing that would return BLK_MQ_RQ_QUEUE_OK
(even though it wasn't) and then run blk_mq_requeue_request() followed
by blk_mq_kick_requeue_list().
Also, document that DM blk-mq ontop of old request_fn devices cannot
fail in clone_rq() since the clone request is preallocated as part of
the pdu.
Reported-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: e5863d9ad ("dm: allocate requests in target when stacking on blk-mq devices") Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org # 4.0+
Junichi Nomura [Wed, 27 May 2015 04:22:07 +0000 (04:22 +0000)]
dm: fix NULL pointer when clone_and_map_rq returns !DM_MAPIO_REMAPPED
When stacking request-based DM on blk_mq device, request cloning and
remapping are done in a single call to target's clone_and_map_rq().
The clone is allocated and valid only if clone_and_map_rq() returns
DM_MAPIO_REMAPPED.
The "IS_ERR(clone)" check in map_request() does not cover all the
!DM_MAPIO_REMAPPED cases that are possible (E.g. if underlying devices
are not ready or unavailable, clone_and_map_rq() may return
DM_MAPIO_REQUEUE without ever having established an ERR_PTR). Fix this
by explicitly checking for a return that is not DM_MAPIO_REMAPPED in
map_request().
Without this fix, DM core may call setup_clone() for a NULL clone
and oops like this:
Junichi Nomura [Tue, 26 May 2015 08:25:54 +0000 (08:25 +0000)]
dm: run queue on re-queue
Without kicking queue, requeued request may stay forever in
the queue if there are no other I/O activities to the device.
The original error had been in v2.6.39 with commit 7eaceaccab5f
("block: remove per-queue plugging"), which replaced conditional
plugging by periodic runqueue.
Commit 9d1deb83d489 in v4.1-rc1 removed the periodic runqueue
and the problem started to manifest.
Fixes: 9d1deb83d489 ("dm: don't schedule delayed run of the queue if nothing to do") Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Linus Torvalds [Sun, 24 May 2015 18:15:28 +0000 (11:15 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five fixes: Two MAINTAINER email updates (urgent
because the non-avagotech emails will start bouncing) an lpfc big
endian oops fix, a 256 byte sector hang fix (to eliminate 256 byte
sectors) and a storvsc fix which could cause test unit ready failures
on bringup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: Revise lpfc maintainers for Avago Technologies ownership of Emulex
MAINTAINERS, be2iscsi: change email domain
sd: Disable support for 256 byte/sector disks
lpfc: Fix breakage on big endian kernels
storvsc: Set the SRB flags correctly when no data transfer is needed
Linus Torvalds [Sat, 23 May 2015 18:28:25 +0000 (11:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two Ceph fixes from Sage Weil:
"These fix an issue with the RBD notifications when there are topology
changes in the cluster"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
libceph: request a new osdmap if lingering request maps to no osd
Linus Torvalds [Sat, 23 May 2015 18:14:10 +0000 (11:14 -0700)]
Merge branch 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I fixed up a regression from 4.0 where conversion between different
raid levels would sometimes bail out without converting.
Filipe tracked down a race where it was possible to double allocate
chunks on the drive.
Mark has a fix for fiemap. All three will get bundled off for stable
as well"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix regression in raid level conversion
Btrfs: fix racy system chunk allocation when setting block group ro
btrfs: clear 'ret' in btrfs_check_shared() loop
Linus Torvalds [Sat, 23 May 2015 00:34:24 +0000 (17:34 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Linus Torvalds [Fri, 22 May 2015 22:15:30 +0000 (15:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
Linus Torvalds [Fri, 22 May 2015 21:49:55 +0000 (14:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Problem here is that br_forward_delay_timer_expired() is a timer
handler, calling br_ifinfo_notify() which assumes either rcu_read_lock()
or RTNL are held.
Simplest fix seems to add rcu read lock section.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Reported-by: Dominick Grift <dac.override@gmail.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: core: 'ethtool' issue with querying phy settings
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com> Reviewed-by: Ray Jui <rjui@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.") Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:10 +0000 (09:22 -0500)]
net: macb: Disable half duplex gigabit on Zynq
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:09 +0000 (09:22 -0500)]
net: macb: Document zynq gem dt binding
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Fri, 22 May 2015 11:40:09 +0000 (13:40 +0200)]
ipv4: fill in table id when replacing a route
When replacing an IPv4 route, tb_id member of the new fib_alias
structure is not set in the replace code path so that the new route is
ignored.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 22 May 2015 11:15:22 +0000 (13:15 +0200)]
cdc_ncm: Fix tx_bytes statistics
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Reported-by: Florian Bruhin <me@the-compiler.org> Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 May 2015 04:51:19 +0000 (21:51 -0700)]
tcp: fix a potential deadlock in tcp_get_info()
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dm-multipath has to clone the bios for every request sent
to the lower devices, which wastes cpu cycles and ties down memory.
This patch instead adds a new REQ_CLONE flag that instructs req_bio_endio
to not complete bios attached to a request, which we set on clone
requests similar to bios in a flush sequence. With this change I/O
errors on a path failure only get propagated to dm-multipath, which
can then either resubmit the I/O or complete the bios on the original
request.
I've done some basic testing of this on a Linux target with ALUA support,
and it survives path failures during I/O nicely.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Mike Snitzer [Fri, 22 May 2015 13:14:03 +0000 (09:14 -0400)]
block: remove management of bi_remaining when restoring original bi_end_io
Commit c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for
non-chains") regressed all existing callers that followed this pattern:
1) saving a bio's original bi_end_io
2) wiring up an intermediate bi_end_io
3) restoring the original bi_end_io from intermediate bi_end_io
4) calling bio_endio() to execute the restored original bi_end_io
The regression was due to BIO_CHAIN only ever getting set if
bio_inc_remaining() is called. For the above pattern it isn't set until
step 3 above (step 2 would've needed to establish BIO_CHAIN). As such
the first bio_endio(), in step 2 above, never decremented __bi_remaining
before calling the intermediate bi_end_io -- leaving __bi_remaining with
the value 1 instead of 0. When bio_inc_remaining() occurred during step
3 it brought it to a value of 2. When the second bio_endio() was
called, in step 4 above, it should've called the original bi_end_io but
it didn't because there was an extra reference that wasn't dropped (due
to atomic operations being optimized away since BIO_CHAIN wasn't set
upfront).
Fix this issue by removing the __bi_remaining management complexity for
all callers that use the above pattern -- bio_chain() is the only
interface that _needs_ to be concerned with __bi_remaining. For the
above pattern callers just expect the bi_end_io they set to get called!
Remove bio_endio_nodec() and also remove all bio_inc_remaining() calls
that aren't associated with the bio_chain() interface.
Also, the bio_inc_remaining() interface has been moved local to bio.c.
Fixes: c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for non-chains") Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Dave Airlie [Fri, 22 May 2015 03:31:03 +0000 (13:31 +1000)]
Merge tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel into drm-fixes
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
crypto: s390/ghash - Fix incorrect ghash icv buffer handling.
Multitheaded tests showed that the icv buffer in the current ghash
implementation is not handled correctly. A move of this working ghash
buffer value to the descriptor context fixed this. Code is tested and
verified with an multithreaded application via af_alg interface.
Cc: stable@vger.kernel.org Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by: Gerald Schaefer <geraldsc@linux.vnet.ibm.com> Reported-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Fri, 22 May 2015 02:54:50 +0000 (19:54 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes.
Three for our crypto code, two for eBPF, and one memory management fix
to get machines with memory > 8TB working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: correct return value of pmd_pfn
s390/crypto: fix stckf loop
s390/zcrypt: Fix invalid domain handling during ap module unload
s390/bpf: Fix gcov stack space problem
s390/zcrypt: fixed ap poll timer behavior
s390/bpf: Adjust ALU64_DIV/MOD to match interpreter change
Linus Torvalds [Fri, 22 May 2015 00:54:00 +0000 (17:54 -0700)]
Merge tag 'sound-4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch became slightly large, just because I've been on vacation
for the last two weeks. Nothing to scare much here, all
device-specific fixes, mostly small patches.
Majority of patches are for HD-audio, especially Dell machines. The
rest are small ASoC fixes for various codecs, and a USB-audio quirk.
One PCM fix is included to ease the faulty condition checks in the
case of two periods PCM buffers"
* tag 'sound-4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable widget power-saving for ALC292 & co
ALSA: hda - Reduce verbs by node power-saves
ALSA: sound/atmel/ac97c.c: remove unused variable
ALSA: usb-audio: Add quirk for MS LifeCam Studio
ALSA: pcm: Modify double acknowledged interrupts check condition
ALSA: hda/realtek - ALC292 dock fix for Thinkpad L450
ALSA: hda - Add Conexant codecs CX20721, CX20722, CX20723 and CX20724
ALSA: hda - Fix headset mic and mic-in for a Dell desktop
ASoC: wm8994: correct BCLK DIV 348 to 384
ASoC: wm8960: fix "RINPUT3" audio route error
ASoC: dapm: Modify widget stream name according to prefix
ALSA: hda - Add headset mic quirk for Dell Inspiron 5548
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ASoC: rt5645: Add ACPI match ID
ALSA: hda/realtek - Add ALC298 alias name for Dell
ASoC: uda1380: Avoid accessing i2c bus when codec is disabled
ALSA: hda/realtek - Fix typo for ALC286/ALC288
ASoC: mc13783: Fix wrong mask value used in mc13xxx_reg_rmw() calls
ALSA: hda - Add headphone quirk for Lifebook E752
ASoC: davinci-mcasp: Correct pm status check in suspend callback
Linus Torvalds [Fri, 22 May 2015 00:36:23 +0000 (17:36 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull infiniband/rdma fixes from Doug Ledford:
"This should hopefully be the last request for 4.1-rc for the RDMA
stack. It contains some late ocrdma fixes that I'm including because
they are small and self contained. It also contains two bug fixes
that are simple and easily verified.
Summary:
- a number of small, well contained bug fixes for ocrdma driver
- a simple fix for the connection negotiation sequence on IB
- fix for broken AF_IB address on UD queue pair support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/cma: Fix broken AF_IB UD support
ib/cm: Change reject message type when destroying cm_id
RDMA/ocrdma: Update ocrdma version number
RDMA/ocrdma: Fail connection for MTU lesser than 512
RDMA/ocrdma: Fix dmac resolution for link local address
RDMA/ocrdma: Prevent allocation of DPP PDs if FW doesnt support it
RDMA/ocrdma: Fix the request length for RDMA_QUERY_QP mailbox command to FW.
RDMA/ocrdma: Use VID 0 if PFC is enabled and vlan is not configured
RDMA/ocrdma: Fix QP state transition in destroy_qp
RDMA/ocrdma: Report EQ full fatal error
RDMA/ocrdma: Fix EQ destroy failure during driver unload
Linus Torvalds [Fri, 22 May 2015 00:23:11 +0000 (17:23 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
Marek Vasut [Fri, 8 May 2015 05:25:49 +0000 (22:25 -0700)]
Input: smtpe-ts - wait 50mS until polling for pen-up
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Marek Vasut [Fri, 8 May 2015 05:24:58 +0000 (22:24 -0700)]
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Linus Torvalds [Thu, 21 May 2015 23:57:50 +0000 (16:57 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
Thomas Hellstrom [Wed, 20 May 2015 21:50:30 +0000 (14:50 -0700)]
Input: joydev - don't classify the vmmouse as a joystick
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Daniel Borkmann [Wed, 20 May 2015 15:13:33 +0000 (17:13 +0200)]
net: sched: fix call_rcu() race on classifier module unloads
Vijay reported that a loop as simple as ...
while true; do
tc qdisc add dev foo root handle 1: prio
tc filter add dev foo parent 1: u32 match u32 0 0 flowid 1
tc qdisc del dev foo root
rmmod cls_u32
done
... will panic the kernel. Moreover, he bisected the change
apparently introducing it to 78fd1d0ab072 ("netlink: Re-add
locking to netlink_lookup() and seq walker").
The removal of synchronize_net() from the netlink socket
triggering the qdisc to be removed, seems to have uncovered
an RCU resp. module reference count race from the tc API.
Given that RCU conversion was done after e341694e3eb5 ("netlink:
Convert netlink_lookup() to use RCU protected hash table")
which added the synchronize_net() originally, occasion of
hitting the bug was less likely (not impossible though):
When qdiscs that i) support attaching classifiers and,
ii) have at least one of them attached, get deleted, they
invoke tcf_destroy_chain(), and thus call into ->destroy()
handler from a classifier module.
After RCU conversion, all classifier that have an internal
prio list, unlink them and initiate freeing via call_rcu()
deferral.
Meanhile, tcf_destroy() releases already reference to the
tp->ops->owner module before the queued RCU callback handler
has been invoked.
Subsequent rmmod on the classifier module is then not prevented
since all module references are already dropped.
By the time, the kernel invokes the RCU callback handler from
the module, that function address is then invalid.
One way to fix it would be to add an rcu_barrier() to
unregister_tcf_proto_ops() to wait for all pending call_rcu()s
to complete.
synchronize_rcu() is not appropriate as under heavy RCU
callback load, registered call_rcu()s could be deferred
longer than a grace period. In case we don't have any pending
call_rcu()s, the barrier is allowed to return immediately.
Since we came here via unregister_tcf_proto_ops(), there
are no users of a given classifier anymore. Further nested
call_rcu()s pointing into the module space are not being
done anywhere.
Only cls_bpf_delete_prog() may schedule a work item, to
unlock pages eventually, but that is not in the range/context
of cls_bpf anymore.
Fixes: 25d8c0d55f24 ("net: rcu-ify tcf_proto") Fixes: 9888faefe132 ("net: sched: cls_basic use RCU") Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: John Fastabend <john.r.fastabend@intel.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Thomas Graf <tgraf@suug.ch> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Work [Tue, 19 May 2015 06:26:23 +0000 (23:26 -0700)]
md/raid0: fix restore to sector variable in raid0_make_request
The variable "sector" in "raid0_make_request()" was improperly updated
by a call to "sector_div()" which modifies its first argument in place.
Commit 47d68979cc968535cb87f3e5f2e6a3533ea48fbd restored this variable
after the call for later re-use. Unfortunetly the restore was done after
the referenced variable "bio" was advanced. This lead to the original
value and the restored value being different. Here we move this line to
the proper place.
One observed side effect of this bug was discarding a file though
unlinking would cause an unrelated file's contents to be discarded.
Signed-off-by: NeilBrown <neilb@suse.de> Fixes: 47d68979cc96 ("md/raid0: fix bug with chunksize not a power of 2.") Cc: stable@vger.kernel.org (any that received above backport)
URL: https://bugzilla.kernel.org/show_bug.cgi?id=98501
Shaohua Li [Wed, 13 May 2015 16:30:08 +0000 (09:30 -0700)]
raid5: fix broken async operation chain
ops_run_reconstruct6() doesn't correctly chain asyn operations. The tx returned
by async_gen_syndrome should be added as the dependent tx of next stripe.
Hans de Goede [Wed, 20 May 2015 21:37:41 +0000 (14:37 -0700)]
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=1025058
Matthew Finlay [Tue, 19 May 2015 07:11:48 +0000 (00:11 -0700)]
IB/cma: Fix broken AF_IB UD support
Support for using UD and AF_IB is currently broken. The
IB_CM_SIDR_REQ_RECEIVED message is not handled properly in
cma_save_net_info() and we end up falling into code that will try and
process the request as ipv4/ipv6, which will end up failing.
The resolution is to add a check for the SIDR_REQ and call
cma_save_ib_info() with a NULL path record. Change cma_save_ib_info()
to copy the src sib info from the listen_id when the path record is NULL.
Reported-by: Hari Shankar <Hari.Shankar@netapp.com> Signed-off-by: Matt Finlay <matt@mellanox.com> Acked-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Minghuan Lian [Wed, 20 May 2015 15:13:15 +0000 (10:13 -0500)]
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
When allocating a device table, if the requested allocation is smaller
than the default granule size of the ITS then, we need to round up to
the default size.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[ stuart: Added comments and massaged changelog ] Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Reviewed-by: Marc Zygnier <marc.zyngier@arm.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1432134795-661-1-git-send-email-stuart.yoder@freescale.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chris Mason [Wed, 20 May 2015 01:54:41 +0000 (18:54 -0700)]
Btrfs: fix regression in raid level conversion
Commit 2f0810880f082fa8ba66ab2c33b02e4ff9770a5e changed
btrfs_set_block_group_ro to avoid trying to allocate new chunks with the
new raid profile during conversion. This fixed failures when there was
no space on the drive to allocate a new chunk, but the metadata
reserves were sufficient to continue the conversion.
But this ended up causing a regression when the drive had plenty of
space to allocate new chunks, mostly because reduce_alloc_profile isn't
using the new raid profile.
Fixing btrfs_reduce_alloc_profile is a bigger patch. For now, do a
partial revert of 2f0810880, and don't error out if we hit ENOSPC.
Signed-off-by: Chris Mason <clm@fb.com> Tested-by: Dave Sterba <dsterba@suse.cz> Reported-by: Holger Hoffstaette <holger.hoffstaette@googlemail.com>
.. which introduced a regression that prevented all lingering requests
requeued in kick_requests() from ever being sent to the OSDs, resulting
in a lot of missed notifies. In retrospect it's pretty obvious that
r_req_lru_item item in the case of lingering requests can be used not
only for notarget, but also for unsent linkage due to how tightly
actual map and enqueue operations are coupled in __map_request().
The assertion that was being silenced is taken care of in the previous
("libceph: request a new osdmap if lingering request maps to no osd")
commit: by always kicking homeless lingering requests we ensure that
none of them ends up on the notarget list outside of the critical
section guarded by request_mutex.
Cc: stable@vger.kernel.org # 3.18+, needs b0494532214b "libceph: request a new osdmap if lingering request maps to no osd" Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com>
Ilya Dryomov [Mon, 11 May 2015 14:53:10 +0000 (17:53 +0300)]
libceph: request a new osdmap if lingering request maps to no osd
This commit does two things. First, if there are any homeless
lingering requests, we now request a new osdmap even if the osdmap that
is being processed brought no changes, i.e. if a given lingering
request turned homeless in one of the previous epochs and remained
homeless in the current epoch. Not doing so leaves us with a stale
osdmap and as a result we may miss our window for reestablishing the
watch and lose notifies.
MON=1 OSD=1:
# cat linger-needmap.sh
#!/bin/bash
rbd create --size 1 test
DEV=$(rbd map test)
ceph osd out 0
rbd map dne/dne # obtain a new osdmap as a side effect (!)
sleep 1
ceph osd in 0
rbd resize --size 2 test
# rbd info test | grep size -> 2M
# blockdev --getsize $DEV -> 1M
N.B.: Not obtaining a new osdmap in between "osd out" and "osd in"
above is enough to make it miss that resize notify, but that is a
bug^Wlimitation of ceph watch/notify v1.
Second, homeless lingering requests are now kicked just like those
lingering requests whose mapping has changed. This is mainly to
recognize that a homeless lingering request makes no sense and to
preserve the invariant that a registered lingering request is not
sitting on any of r_req_lru_item lists. This spares us a WARN_ON,
which commit ba9d114ec557 ("libceph: clear r_req_lru_item in
__unregister_linger_request()") tried to fix the _wrong_ way.
Ted Kim [Thu, 14 May 2015 19:49:01 +0000 (12:49 -0700)]
ib/cm: Change reject message type when destroying cm_id
Problem reported by: Ted Kim <ted.h.kim@oracle.com>:
We have a case where a Linux system and a non-Linux system are
trying to interoperate. The Linux host is the active side and
starts the connection establishment, but later decides to not go
through with the connection setup and does rdma_destroy_id().
The rdma_destroy_id() eventually works its way down to cm_destroy_id()
in core/cm.c, where a REJ is sent. The non-Linux system
has some trouble recognizing the REJ because of:
A. CM states which can't receive the REJ
B. Some issues about REJ formatting (missing comm ID)
ISSUE A: That part of the spec says, a Consumer Reject REJ can be
sent for a connection abort, but it goes further
and says: can send a REJ message with a "Consumer Reject"
Reason code if they are in a CM state (i.e. REP
Rcvd, MRA(REP) Sent, REQ Rcvd, MRA Sent) that allows
a REJ to be sent (lines 35-38).
Of the states listed there in that sentence, it would
seem to limit the active side to using the Consumer Reject
(for the abort case) in just the REP-Rcvd and MRA-REP-Sent
states. That is basically only after the active side
sees a REP (or alternatively goes down the state transitions
to timeout in which case a Timeout REJ is sent).
As a fix, in cm-destroy-id() move the IB-CM-MRA-REQ-RCVD case
to the same as REQ-SENT. Essentially, make a REJ sent after
getting an MRA on active side a timeout rather than Consumer-
Reject, which is arguably more correct with the CM state
diagrams previous to getting a REP.
Signed-off-by: Ted Kim <ted.h.kim@oracle.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Tim Beale [Mon, 18 May 2015 03:38:38 +0000 (15:38 +1200)]
net: phy: Make sure phy_start() always re-enables the phy interrupts
This is an alternative way of fixing:
commit db9683fb412d ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
(1) When adding a nexthop of a multipath route fails (e.g. because of a
conflict with an existing route), we are supposed to delete nexthops
already added. However, currently we try to also delete all nexthops we
haven't even tried to add yet so that a "ip route add" command can
actually remove pre-existing routes if it fails.
(2) Attempt to replace a multipath route results in a broken siblings
linked list. Following commands (like "ip route del") can then either
follow a link into freed memory or end in an infinite loop (if the slab
object has been reused).
v2: fix an omission in first patch
v3: change the semantics of replace operation to better match IPv4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 18 May 2015 18:54:00 +0000 (20:54 +0200)]
ipv6: fix ECMP route replacement
When replacing an IPv6 multipath route with "ip route replace", i.e.
NLM_F_CREATE | NLM_F_REPLACE, fib6_add_rt2node() replaces only first
matching route without fixing its siblings, resulting in corrupted
siblings linked list; removing one of the siblings can then end in an
infinite loop.
IPv6 ECMP implementation is a bit different from IPv4 so that route
replacement cannot work in exactly the same way. This should be a
reasonable approximation:
1. If the new route is ECMP-able and there is a matching ECMP-able one
already, replace it and all its siblings (if any).
2. If the new route is ECMP-able and no matching ECMP-able route exists,
replace first matching non-ECMP-able (if any) or just add the new one.
3. If the new route is not ECMP-able, replace first matching
non-ECMP-able route (if any) or add the new route.
We also need to remove the NLM_F_REPLACE flag after replacing old
route(s) by first nexthop of an ECMP route so that each subsequent
nexthop does not replace previous one.
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 18 May 2015 18:53:55 +0000 (20:53 +0200)]
ipv6: do not delete previously existing ECMP routes if add fails
If adding a nexthop of an IPv6 multipath route fails, comment in
ip6_route_multipath() says we are going to delete all nexthops already
added. However, current implementation deletes even the routes it
hasn't even tried to add yet. For example, running
ip route add 1234:5678::/64 \
nexthop via fe80::aa dev dummy1 \
nexthop via fe80::bb dev dummy1 \
nexthop via fe80::cc dev dummy1
twice results in removing all routes first command added.
Limit the second (delete) run to nexthops that succeeded in the first
(add) run.
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Wed, 6 May 2015 04:26:27 +0000 (12:26 +0800)]
block: replace trylock with mutex_lock in blkdev_reread_part()
The only possible problem of using mutex_lock() instead of trylock
is about deadlock.
If there aren't any locks held before calling blkdev_reread_part(),
deadlock can't be caused by this conversion.
If there are locks held before calling blkdev_reread_part(),
and if these locks arn't required in open, close handler and I/O
path, deadlock shouldn't be caused too.
Both user space's ioctl(BLKRRPART) and md_setup_drive() from
init/do_mounts_md.c belongs to the 1st case, so the conversion is safe
for the two cases.
For loop, the previous patches in this pathset has fixed the ABBA lock
dependency, so the conversion is OK.
For nbd, tx_lock is held when calling the function:
- both open and release won't hold the lock
- when blkdev_reread_part() is run, I/O thread has been stopped
already, so tx_lock won't be acquired in I/O path at that time.
- so the conversion won't cause deadlock for nbd
For dasd, both dasd_open(), dasd_release() and request function don't
acquire any mutex/semphone, so the conversion should be safe.
Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Jarod Wilson <jarod@redhat.com> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Jarod Wilson [Wed, 6 May 2015 04:26:22 +0000 (12:26 +0800)]
block: export blkdev_reread_part() and __blkdev_reread_part()
This patch exports blkdev_reread_part() for block drivers, also
introduce __blkdev_reread_part().
For some drivers, such as loop, reread of partitions can be run
from the release path, and bd_mutex may already be held prior to
calling ioctl_by_bdev(bdev, BLKRRPART, 0), so introduce
__blkdev_reread_part for use in such cases.
CC: Christoph Hellwig <hch@lst.de> CC: Jens Axboe <axboe@kernel.dk> CC: Tejun Heo <tj@kernel.org> CC: Alexander Viro <viro@zeniv.linux.org.uk> CC: Markus Pargmann <mpa@pengutronix.de> CC: Stefan Weinhuber <wein@de.ibm.com> CC: Stefan Haberland <stefan.haberland@de.ibm.com> CC: Sebastian Ott <sebott@linux.vnet.ibm.com> CC: Fabian Frederick <fabf@skynet.be> CC: Ming Lei <ming.lei@canonical.com> CC: David Herrmann <dh.herrmann@gmail.com> CC: Andrew Morton <akpm@linux-foundation.org> CC: Peter Zijlstra <peterz@infradead.org> CC: nbd-general@lists.sourceforge.net CC: linux-s390@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com>
netfilter: nfnetlink_{log,queue}: Register pernet in first place
nfnetlink_{log,queue}_init() register the netlink callback nf*_rcv_nl_event
before registering the pernet_subsys, but the callback relies on data
structures allocated by pernet init functions.
When nfnetlink_{log,queue} is loaded, if a netlink message is received after
the netlink callback is registered but before the pernet_subsys is registered,
the kernel will panic in the sequence
nfulnl_rcv_nl_event
nfnl_log_pernet
net_generic
BUG_ON(id == 0) where id is nfnl_log_net_id.
The panic can be easily reproduced in 4.0.3 by:
while true ;do modprobe nfnetlink_log ; rmmod nfnetlink_log ; done &
while true ;do ip netns add dummy ; ip netns del dummy ; done &
This patch moves register_pernet_subsys to earlier in nfnetlink_log_init.
Notice that the BUG_ON hit in 4.0.3 was recently removed in 2591ffd308
["netns: remove BUG_ONs from net_generic()"].
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liang Li [Wed, 20 May 2015 20:41:25 +0000 (04:41 +0800)]
kvm/fpu: Enable eager restore kvm FPU for MPX
The MPX feature requires eager KVM FPU restore support. We have verified
that MPX cannot work correctly with the current lazy KVM FPU restore
mechanism. Eager KVM FPU restore should be enabled if the MPX feature is
exposed to VM.
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com> Signed-off-by: Liang Li <liang.z.li@intel.com>
[Also activate the FPU on AMD processors. - Paolo] Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm: fix crash in kvm_vcpu_reload_apic_access_page
memslot->userfault_addr is set by the kernel with a mmap executed
from the kernel but the userland can still munmap it and lead to the
below oops after memslot->userfault_addr points to a host virtual
address that has no vma or mapping.
Ping Cheng [Wed, 20 May 2015 00:42:02 +0000 (17:42 -0700)]
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
We assumed all touch interfaces report touch data. But, Bamboo
and Intuos non-touch devices report express keys on touch
interface. We need to check touch_max before counting touches.
Takashi Iwai [Wed, 20 May 2015 04:56:23 +0000 (06:56 +0200)]
ALSA: hda - Disable widget power-saving for ALC292 & co
We've got reports that ALC3226 (a Dell variant of ALC292) gives click
noises at transition from D3 to D0 when the widget power-saving is
enabled. Further debugging session showed that avoiding it isn't
trivial, unfortunately, since paths are basically activated
dynamically while the pins have been already enabled.
This patch disables the widget power-saving for such codecs.
Reported-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 20 May 2015 04:49:37 +0000 (06:49 +0200)]
ALSA: hda - Reduce verbs by node power-saves
The widget (node) power-saves restore the widget states at each
transition from D3 to D0 on each node. This was added in the commit
[d545a57c5f84:ALSA: hda - Sync node attributes at resume from widget
power saving]. However, the test was rater false-positive; this
wasn't needed for any codecs.
Since the resync may take significant number of additional verbs to be
executed, it's better to reduce it. Let's disable it for now again.
Filipe Manana [Mon, 18 May 2015 18:11:40 +0000 (19:11 +0100)]
Btrfs: fix racy system chunk allocation when setting block group ro
If while setting a block group read-only we end up allocating a system
chunk, through check_system_chunk(), we were not doing it while holding
the chunk mutex which is a problem if a concurrent chunk allocation is
happening, through do_chunk_alloc(), as it means both block groups can
end up using the same logical addresses and physical regions in the
device(s). So make sure we hold the chunk mutex.
Cc: stable@vger.kernel.org # 4.0+ Fixes: 2f0810880f08 ("btrfs: delete chunk allocation attemp when
setting block group ro")
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
Mark Fasheh [Tue, 19 May 2015 19:49:50 +0000 (12:49 -0700)]
btrfs: clear 'ret' in btrfs_check_shared() loop
btrfs_check_shared() is leaking a return value of '1' from
find_parent_nodes(). As a result, callers (in this case, extent_fiemap())
are told extents are shared when they are not. This in turn broke fiemap on
btrfs for kernels v3.18 and up.
The fix is simple - we just have to clear 'ret' after we are done processing
the results of find_parent_nodes().
It wasn't clear to me at first what was happening with return values in
btrfs_check_shared() and find_parent_nodes() - thanks to Josef for the help
on irc. I added documentation to both functions to make things more clear
for the next hacker who might come across them.
If we could queue this up for -stable too that would be great.
Signed-off-by: Mark Fasheh <mfasheh@suse.de> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com>
Dave Airlie [Tue, 19 May 2015 23:22:00 +0000 (09:22 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Summary:
- Use generic function to get buffer count instead of specific one.
In case of Exynos DRM, There was a special case which decides pixel
format of a given buffer according to planer types, which is NV12M and NV12.
However, NV12M doesn't exist in drm fourcc so it removes
exynos_drm_format_num_buffers() specific to Exynos DRM and use a generic function,
drm_format_num_planes() instead.
- Allow mixer driver to support NV21 format for Video processor.
This format was already supported but we just missed DRM_FORMAT_NV21 case
so this patch considers the case so that Mixer driver can handle it correctly.
- Add regression fix and some code cleanups.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
Yuchung Cheng [Mon, 18 May 2015 19:31:45 +0000 (12:31 -0700)]
tcp: don't over-send F-RTO probes
After sending the new data packets to probe (step 2), F-RTO may
incorrectly send more probes if the next ACK advances SND_UNA and
does not sack new packet. However F-RTO RFC 5682 probes at most
once. This bug may cause sender to always send new data instead of
repairing holes, inducing longer HoL blocking on the receiver for
the application.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Mon, 18 May 2015 19:31:44 +0000 (12:31 -0700)]
tcp: only undo on partial ACKs in CA_Loss
Undo based on TCP timestamps should only happen on ACKs that advance
SND_UNA, according to the Eifel algorithm in RFC 3522:
Section 3.2:
(4) If the value of the Timestamp Echo Reply field of the
acceptable ACK's Timestamps option is smaller than the
value of RetransmitTS, then proceed to step (5),
Section Terminology:
We use the term 'acceptable ACK' as defined in [RFC793]. That is an
ACK that acknowledges previously unacknowledged data.
This is because upon receiving an out-of-order packet, the receiver
returns the last timestamp that advances RCV_NXT, not the current
timestamp of the packet in the DUPACK. Without checking the flag,
the DUPACK will cause tcp_packet_delayed() to return true and
tcp_try_undo_loss() will revert cwnd reduction.
Note that we check the condition in CA_Recovery already by only
calling tcp_try_undo_partial() if FLAG_SND_UNA_ADVANCED is set or
tcp_try_undo_recovery() if snd_una crosses high_seq.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log