Duane Griffin [Thu, 9 Oct 2008 03:28:31 +0000 (23:28 -0400)]
jbd2: abort instead of waiting for nonexistent transaction
The __jbd2_log_wait_for_space function sits in a loop checkpointing
transactions until there is sufficient space free in the journal.
However, if there are no transactions to be processed (e.g. because the
free space calculation is wrong due to a corrupted filesystem) it will
never progress.
Check for space being required when no transactions are outstanding and
abort the journal instead of endlessly looping.
This patch fixes the bug reported by Sami Liedes at:
http://bugzilla.kernel.org/show_bug.cgi?id=10976
Signed-off-by: Duane Griffin <duaneg@dghda.com> Cc: Sami Liedes <sliedes@cc.hut.fi> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Frederic Bohe [Fri, 10 Oct 2008 12:09:18 +0000 (08:09 -0400)]
ext4: fix initialization of UNINIT bitmap blocks
This fixes a bug which caused on-line resizing of filesystems with a
1k blocksize to fail. The root cause of this bug was the fact that if
an uninitalized bitmap block gets read in by userspace (which
e2fsprogs does try to avoid, but can happen when the blocksize is less
than the pagesize and an adjacent blocks is read into memory)
ext4_read_block_bitmap() was erroneously depending on the buffer
uptodate flag to decide whether it needed to initialize the bitmap
block in memory --- i.e., to set the standard set of blocks in use by
a block group (superblock, bitmaps, inode table, etc.). Essentially,
ext4_read_block_bitmap() assumed it was the only routine that might
try to read a block containing a block bitmap, which is simply not
true.
To fix this, ext4_read_block_bitmap() and ext4_read_inode_bitmap()
must always initialize uninitialized bitmap blocks. Once a block or
inode is allocated out of that bitmap, it will be marked as
initialized in the block group descriptor, so in general this won't
result any extra unnecessary work.
Theodore Ts'o [Fri, 10 Oct 2008 03:53:47 +0000 (23:53 -0400)]
ext4: Use readahead when reading an inode from the inode table
With modern hard drives, reading 64k takes roughly the same time as
reading a 4k block. So request readahead for adjacent inode table
blocks to reduce the time it takes when iterating over directories
(especially when doing this in htree sort order) in a cold cache case.
With this patch, the time it takes to run "git status" on a kernel
tree after flushing the caches via "echo 3 > /proc/sys/vm/drop_caches"
is reduced by 21%.
ext4: Combine proc file handling into a single set of functions
Previously mballoc created a separate set of functions for each proc
file. This combines the tunables into a single set of functions which
gets used for all of the per-superblock proc files, saving
approximately 2k of compiled object code.
ext4: Don't use 'struct dentry' for internal lookups
This is a port of a patch from Linus which fixes a 200+ byte stack
usage problem in ext4_get_parent().
It's more efficient to pass down only the actual parts of the dentry
that matter: the parent inode and the name, instead of allocating a
struct dentry on the stack.
Eric Sandeen [Sat, 13 Sep 2008 19:23:29 +0000 (15:23 -0400)]
ext4: use percpu data structures for lg_prealloc_list
lg_prealloc_list seems to cry out for a per-cpu data structure; on a large
smp system I think this should be better. I've lightly tested this change
on a 4-cpu system.
Pick an ioctl number for EXT4_IOC_MIGRATE that won't conflict with
other ext4 ioctl's. Since there haven't been any major userspace
users of this ioctl, we can afford to change this now, to avoid
potential problems later.
Also, reorder the ioctl numbers in ext4.h to avoid this sort of
mistake in the future.
ext4: hook the ext3 migration interface to the EXT4_IOC_SETFLAGS ioctl
This patch hooks the ext3 to ext4 migrate interface to
EXT4_IOC_SETFLAGS ioctl. The userspace interface is via chattr +e. We
only allow setting extent flags. Clearing extent flag (migrating from
ext4 to ext3) is not supported.
Li Zefan [Mon, 8 Sep 2008 14:47:19 +0000 (10:47 -0400)]
ext4: add missing unlock in ext4_check_descriptors() on error path
If there group descriptors are corrupted we need unlock the block
group lock before returning from the function; else we will oops when
freeing a spinlock which is still being held.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
jbd2: clean up how the journal device name is printed
Calculate the journal device name once and stash it away in the
journal_s structure. This avoids needing to call bdevname()
everywhere and reduces stack usage by not needing to allocate an
on-stack buffer. In addition, we eliminate the '/' that can appear in
device names (e.g. "cciss/c0d0p9" --- see kernel bugzilla #11321) that
can cause problems when creating proc directory names, and include the
inode number to support ocfs2 which creates multiple journals with
different inode numbers.
Eric Sandeen [Thu, 9 Oct 2008 15:15:52 +0000 (11:15 -0400)]
ext4: Avoid printk floods in the face of directory corruption
Note: some people thinks this represents a security bug, since it
might make the system go away while it is printing a large number of
console messages, especially if a serial console is involved. Hence,
it has been assigned CVE-2008-3528, but it requires that the attacker
either has physical access to your machine to insert a USB disk with a
corrupted filesystem image (at which point why not just hit the power
button), or is otherwise able to convince the system administrator to
mount an arbitrary filesystem image (at which point why not just
include a setuid shell or world-writable hard disk device file or some
such). Me, I think they're just being silly. --tytso
With delayed allocation we use i_data_sem to update i_disksize. We need
to update i_disksize only if the new size specified is greater than the
current value and we need to make sure we don't race with other
i_disksize update. With delayed allocation we will switch to the
write_begin function for non-delayed allocation if we are low on free
blocks. This means the write_begin function for non-delayed allocation
also needs to use the same locking.
We also need to check and update i_disksize even if the new size is less
that inode.i_size because of delayed allocation.
ext4: truncate block allocated on a failed ext4_write_begin
For blocksize < pagesize we need to remove blocks that got allocated in
block_write_begin() if we fail with ENOSPC for later blocks.
block_write_begin() internally does this if it allocated pages locally.
This makes sure we don't have blocks outside inode.i_size during ENOSPC.
ext4: Retry block allocation if we have free blocks left
When we truncate files, the meta-data blocks released are not reused
untill we commit the truncate transaction. That means delayed get_block
request will return ENOSPC even if we have free blocks left. Force a
journal commit and retry block allocation if we get ENOSPC with free
blocks left.
ext4: Don't add the inode to journal handle until after the block is allocated
Make sure we don't add the inode to the journal handle until after the
block allocation, so that a journal commit will not include the inode in
case of block allocation failure.
We run into ENOSPC error on nonmballoc ext4, even when there is free blocks
on the filesystem.
The patch includes two changes:
a) Set reservation to NULL if we trying to allocate near group_target_block
from the goal group if the free block in the group is less than windows.
This should give us a better chance to allocate near group_target_block.
This also ensures that if we are not allocating near group_target_block
then we don't trun off reservation. This should enable us to allocate
with reservation from other groups that have large free blocks count.
b) we don't need to check the window size if the block reservation is off.
ext4: Switch to non delalloc mode when we are low on free blocks count.
The delayed allocation code allocates blocks during writepages(), which
can not handle block allocation failures. To deal with this, we switch
away from delayed allocation mode when we are running low on free
blocks. This also allows us to avoid needing to reserve a large number
of meta-data blocks in case all of the requested blocks are
discontiguous.
This patch adds dirty block accounting using percpu_counters. Delayed
allocation block reservation is now done by updating dirty block
counter. In a later patch we switch to non delalloc mode if the
filesystem free blocks is greater than 150% of total filesystem dirty
blocks
During block reservation if we don't have enough blocks left, retry
block reservation with smaller block counts. This makes sure we try
fallocate and DIO with smaller request size and don't fail early. The
delayed allocation reservation cannot try with smaller block count. So
retry block reservation to handle temporary disk full conditions. Also
print free blocks details if we fail block allocation during writepages.
ext4: Make sure all the block allocation paths reserve blocks
With delayed allocation we need to make sure block are reserved before
we attempt to allocate them. Otherwise we get block allocation failure
(ENOSPC) during writepages which cannot be handled. This would mean
silent data loss (We do a printk stating data will be lost). This patch
updates the DIO and fallocate code path to do block reservation before
block allocation. This is needed to make sure parallel DIO and fallocate
request doesn't take block out of delayed reserve space.
When free blocks count go below a threshold we switch to a slow patch
which looks at other CPU's accumulated percpu counter values.
ext4: invalidate pages if delalloc block allocation fails.
We are a bit agressive in invalidating all the pages. But
it is ok because we really don't know why the block allocation
failed and it is better to come of the writeback path
so that user can look for more info.
Mingming Cao [Thu, 9 Oct 2008 16:50:59 +0000 (12:50 -0400)]
percpu counter: clean up percpu_counter_sum_and_set()
percpu_counter_sum_and_set() and percpu_counter_sum() is the same except
the former updates the global counter after accounting. Since we are
taking the fbc->lock to calculate the precise value of the counter in
percpu_counter_sum() anyway, it should simply set fbc->count too, as the
percpu_counter_sum_and_set() does.
This patch merges these two interfaces into one.
Signed-off-by: Mingming Cao <cmm@us.ibm.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Linus Torvalds [Thu, 9 Oct 2008 21:04:54 +0000 (14:04 -0700)]
Don't allow splice() to files opened with O_APPEND
This is debatable, but while we're debating it, let's disallow the
combination of splice and an O_APPEND destination.
It's not entirely clear what the semantics of O_APPEND should be, and
POSIX apparently expects pwrite() to ignore O_APPEND, for example. So
we could make up any semantics we want, including the old ones.
But Miklos convinced me that we should at least give it some thought,
and that accepting writes at arbitrary offsets is wrong at least for
IS_APPEND() files (which always have O_APPEND set, even if the reverse
isn't true: you can obviously have O_APPEND set on a regular file).
So disallow O_APPEND entirely for now. I doubt anybody cares, and this
way we have one less gray area to worry about.
Matt Mackall [Wed, 8 Oct 2008 19:51:57 +0000 (14:51 -0500)]
SLOB: fix bogus ksize calculation fix
This fixes the previous fix, which was completely wrong on closer
inspection. This version has been manually tested with a user-space
test harness and generates sane values. A nearly identical patch has
been boot-tested.
The problem arose from changing how kmalloc/kfree handled alignment
padding without updating ksize to match. This brings it in sync.
Signed-off-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hwmon: (abituguru3) Enable DMI probing feature on Abit AT8 32X
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Daniel Exner <dex@dragonslave.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
hwmon: (abituguru3) Enable reading from AUX3 fan on Abit AT8 32X
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Daniel Exner <dex@dragonslave.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Thu, 9 Oct 2008 13:33:58 +0000 (15:33 +0200)]
hwmon: (it87) Prevent power-off on Shuttle SN68PT
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Corentin Chary [Thu, 9 Oct 2008 13:33:57 +0000 (15:33 +0200)]
eeepc-laptop: Fix hwmon interface
Creates a name file in the sysfs directory, that
is needed for the libsensors library to work.
Also rename fan1_pwm to pwm1 and scale its value as needed.
This fixes bug #11520:
http://bugzilla.kernel.org/show_bug.cgi?id=11520
Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd.
net: Fix netdev_run_todo dead-lock
tcp: Fix possible double-ack w/ user dma
net: only invoke dev->change_rx_flags when device is UP
netrom: Fix sock_orphan() use in nr_release
ax25: Quick fix for making sure unaccepted sockets get destroyed.
Revert "ax25: Fix std timer socket destroy handling."
[Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
[Bluetooth] Add reset quirk for new Targus and Belkin dongles
[Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd.
Because of rounding, in certain conditions, i.e. when in congestion
avoidance state rho is smaller than 1/128 of the current cwnd, TCP
Hybla congestion control starves and the cwnd is kept constant
forever.
This patch forces an increment by one segment after #send_cwnd calls
without increments(newreno behavior).
Signed-off-by: Daniele Lacamera <root@danielinux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 7 Oct 2008 22:50:03 +0000 (15:50 -0700)]
net: Fix netdev_run_todo dead-lock
Benjamin Thery tracked down a bug that explains many instances
of the error
unregister_netdevice: waiting for %s to become free. Usage count = %d
It turns out that netdev_run_todo can dead-lock with itself if
a second instance of it is run in a thread that will then free
a reference to the device waited on by the first instance.
The problem is really quite silly. We were trying to create
parallelism where none was required. As netdev_run_todo always
follows a RTNL section, and that todo tasks can only be added
with the RTNL held, by definition you should only need to wait
for the very ones that you've added and be done with it.
There is no need for a second mutex or spinlock.
This is exactly what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ali Saidi [Tue, 7 Oct 2008 22:31:19 +0000 (15:31 -0700)]
tcp: Fix possible double-ack w/ user dma
From: Ali Saidi <saidi@engin.umich.edu>
When TCP receive copy offload is enabled it's possible that
tcp_rcv_established() will cause two acks to be sent for a single
packet. In the case that a tcp_dma_early_copy() is successful,
copied_early is set to true which causes tcp_cleanup_rbuf() to be
called early which can send an ack. Further along in
tcp_rcv_established(), __tcp_ack_snd_check() is called and will
schedule a delayed ACK. If no packets are processed before the delayed
ack timer expires the packet will be acked twice.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 7 Oct 2008 22:26:48 +0000 (15:26 -0700)]
net: only invoke dev->change_rx_flags when device is UP
Jesper Dangaard Brouer <hawk@comx.dk> reported a bug when setting a VLAN
device down that is in promiscous mode:
When the VLAN device is set down, the promiscous count on the real
device is decremented by one by vlan_dev_stop(). When removing the
promiscous flag from the VLAN device afterwards, the promiscous
count on the real device is decremented a second time by the
vlan_change_rx_flags() callback.
The root cause for this is that the ->change_rx_flags() callback is
invoked while the device is down. The synchronization is meant to mirror
the behaviour of the ->set_rx_mode callbacks, meaning the ->open function
is responsible for doing a full sync on open, the ->close() function is
responsible for doing full cleanup on ->stop() and ->change_rx_flags()
is meant to do incremental changes while the device is UP.
Only invoke ->change_rx_flags() while the device is UP to provide the
intended behaviour.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Mackall [Tue, 7 Oct 2008 16:37:35 +0000 (11:37 -0500)]
SLOB: fix bogus ksize calculation
SLOB's ksize calculation was braindamaged and generally harmlessly
underreported the allocation size. But for very small buffers, it could
in fact overreport them, leading code depending on krealloc to overrun
the allocation and trample other data.
Signed-off-by: Matt Mackall <mpm@selenic.com> Tested-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Theodore Ts'o (tytso@mit.edu) wrote:
>
> I've been playing with adding some markers into ext4 to see if they
> could be useful in solving some problems along with Systemtap. It
> appears, though, that as of 2.6.27-rc8, markers defined in code which is
> compiled directly into the kernel (i.e., not as modules) don't show up
> in Module.markers:
>
> kvm_trace_entryexit arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_entryexit arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
>
> (Note the lack of any of the kernel_sched_* markers, and the markers I
> added for ext4_* and jbd2_* are missing as wel.)
>
> Systemtap apparently depends on in-kernel trace_mark being recorded in
> Module.markers, and apparently it's been claimed that it used to be
> there. Is this a bug in systemtap, or in how Module.markers is getting
> built? And is there a file that contains the equivalent information
> for markers located in non-modules code?
Linus Torvalds [Mon, 6 Oct 2008 21:29:16 +0000 (14:29 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: gart iommu have direct mapping when agp is present too
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
Linus Torvalds [Mon, 6 Oct 2008 21:27:39 +0000 (14:27 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP27: Fix build errors if CONFIG_MAPPED_KERNEL=y
[MIPS] Fix CMP Kconfig configuration and mark as broken.
Linus Torvalds [Mon, 6 Oct 2008 21:27:15 +0000 (14:27 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
atmel-mci: Initialize BLKR before sending data transfer command
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Jarek Poplawski [Mon, 6 Oct 2008 19:54:57 +0000 (12:54 -0700)]
netrom: Fix sock_orphan() use in nr_release
While debugging another bug it was found that NetRom socks
are sometimes seen unorphaned in sk_free(). This patch moves
sock_orphan() in nr_release() to the beginning (like in ax25,
or rose).
Reported-and-tested-by: Bernard Pidoux f6bvp <f6bvp@free.fr> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Oct 2008 19:53:50 +0000 (12:53 -0700)]
ax25: Quick fix for making sure unaccepted sockets get destroyed.
Since we reverted 30902dc3cb0ea1cfc7ac2b17bcf478ff98420d74 ("ax25: Fix
std timer socket destroy handling.") we have to put some kind of fix
in to cure the issue whereby unaccepted connections do not get destroyed.
The approach used here is from Tihomir Heidelberg - 9a4gl
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wessel [Mon, 6 Oct 2008 18:50:59 +0000 (13:50 -0500)]
kgdb: call touch_softlockup_watchdog on resume
The softlockup watchdog needs to be touched when resuming the from the
kgdb stopped state to avoid the printk that a CPU is stuck if the
debugger was active for longer than the softlockup threshold.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Jan Kiszka [Mon, 6 Oct 2008 18:50:59 +0000 (13:50 -0500)]
kgdb, x86: Avoid invoking kgdb_nmicallback twice per NMI
Stress-testing KVM's latest NMI support with kgdbts inside an SMP guest,
I came across spurious unhandled NMIs while running the singlestep test.
Looking closer at the code path each NMI takes when KGDB is enabled, I
noticed that kgdb_nmicallback is called twice per event: One time via
DIE_NMI_IPI notification, the second time on DIE_NMI. Removing the first
invocation cures the unhandled NMIs here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
x86 ACPI: Blacklist two HP machines with buggy BIOSes
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcel Holtmann [Mon, 6 Oct 2008 10:22:52 +0000 (12:22 +0200)]
[Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.
Marcel Holtmann [Mon, 6 Oct 2008 10:22:51 +0000 (12:22 +0200)]
[Bluetooth] Add reset quirk for new Targus and Belkin dongles
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.
Marcel Holtmann [Mon, 6 Oct 2008 10:22:51 +0000 (12:22 +0200)]
[Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.
Ralf Baechle [Sun, 5 Oct 2008 16:23:28 +0000 (18:23 +0200)]
IDE: Fix platform device registration in Swarm IDE driver (v2)
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov [Sun, 5 Oct 2008 16:23:27 +0000 (18:23 +0200)]
ide-cd: temporary tray close fix
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com> Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
Correct firmware type to MTS
Correct audio routing for composite/s-video
Add DVB-T detection.
This patch uses the eeprom hash method for detection as the vendor/product
ids are also used for the DIGIVOX_AD. This may be a clone of the same
product. Explanatory text has been added prior to the hask look-up in
anticipation that it may help others.
The following has been tested to work:
Analogue TV (PAL-I)
Composite In
DVB-T (UK Crystal Palace)
USB AUDIO
The following has not been tested but probably works:
S-Video In
Ralph Loader [Tue, 23 Sep 2008 00:06:48 +0000 (21:06 -0300)]
V4L/DVB (9053): fix buffer overflow in uvc-video
There is a buffer overflow in drivers/media/video/uvc/uvc_ctrl.c:
INFO: 0xf2c5ce08-0xf2c5ce0b. First byte 0xa1 instead of 0xcc
INFO: Allocated in uvc_query_v4l2_ctrl+0x3c/0x239 [uvcvideo] age=13 cpu=1 pid=4975
...
A fixed size 8-byte buffer is allocated, and a variable size field is read
into it; there is no particular bound on the size of the field (it is
dependent on hardware and configuration) and it can overflow [also
verified by inserting printk's.]
The patch attempts to size the buffer to the correctly.
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
Different backends have different input busses (saa7146, flexcop).
To reflect that a config-option to the s5h1420-driver was added which makes
the output mode selectable.
Furthermore the s5h1420-driver is now doing the same i2c-method as it was done
before adding support for other i2c-users.
This patch needs to go into the current release of the kernel, as this driver
is currently broken.
(Thanks to Eberhard Kaltenhaeuser for helping out to debug this issue.)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions dvb_dmxdev_section_callback, dvb_dmxdev_ts_callback,
dvb_dmx_swfilter_packet, dvb_dmx_swfilter_packets, dvb_dmx_swfilter and
dvb_dmx_swfilter_204 may be called from both interrupt and process
context. Therefore they need to be protected by spin_lock_irqsave()
instead of spin_lock().
This fixes a deadlock discovered by lockdep.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Fri, 5 Sep 2008 13:39:27 +0000 (10:39 -0300)]
V4L/DVB (8961): zr36067: Fix RGBR pixel format
The zr36067 driver is improperly declaring pixel format RGBP twice,
once as "16-bit RGB LE" and once as "16-bit RGB BE". The latter is
actually RGBR. Fix the code to properly map both pixel formats.
drivers/media/video/cafe_ccic.c: In function 'cafe_setup_siobuf':
drivers/media/video/cafe_ccic.c:1192: error: implicit declaration of function 'PAGE_ALIGN'
drivers/media/video/cafe_ccic.c: At top level:
drivers/media/video/cafe_ccic.c:1430: error: variable 'cafe_v4l_vm_ops' has initializer but incomplete type
drivers/media/video/cafe_ccic.c:1431: error: unknown field 'open' specified in initializer
drivers/media/video/cafe_ccic.c:1431: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1431: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c:1432: error: unknown field 'close' specified in initializer
drivers/media/video/cafe_ccic.c:1433: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1433: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c: In function 'cafe_v4l_mmap':
drivers/media/video/cafe_ccic.c:1444: error: 'VM_WRITE' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1444: error: (Each undeclared identifier is reported only once
drivers/media/video/cafe_ccic.c:1444: error: for each function it appears in.)
drivers/media/video/cafe_ccic.c:1444: error: 'VM_SHARED' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1461: error: 'VM_DONTEXPAND' undeclared (first use in this function)
This build breakage is caused by some header file shuffle in linux-next. But
I suggest that this patch be merged ahead of linux-next to avoid bisection
breakage.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Sun, 7 Sep 2008 08:56:55 +0000 (05:56 -0300)]
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
The zr36067 driver should return the actual bytes-per-line value when
queried with ioctl VIDIOC_G_FMT, instead of 0. Otherwise user-space
applications can get confused.
Likewise, with ioctl VIDIOC_S_FMT, we are supposed to fill the
bytes-per-line value. And we shouldn't fail if the caller sets the
initial value to something different from 0. This is perfectly valid
for applications to pre-fill this field with the value they expect.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Sun, 7 Sep 2008 08:21:34 +0000 (05:21 -0300)]
V4L/DVB (8957): zr36067: Restore the default pixel format
Restore the default pixel format to YUYV as it used to be before
kernel 2.6.23. It was accidentally changed to BGR3 by commit 603d6f2c8f9f3604f9c6c1f8903efc2df30a000f.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This happens because radio_open assumes that all present bttv devices
have a radio function. If a bttv device without radio and one with
radio are installed on the same system, and the one without radio is
registered first, then radio_open checks for the radio device number
of a bttv device that has no radio function, and this breaks. All we
have to do to fix it is to skip bttv devices without a radio function.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mv-sheeva.git / log