Huang Shijie [Tue, 28 May 2013 06:20:08 +0000 (14:20 +0800)]
ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.
In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.
The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Philipp Zabel [Tue, 4 Jun 2013 09:12:29 +0000 (11:12 +0200)]
ARM i.MX53: tqma53: rev 300 specific pin configuration
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.
ARM: dts: imx27-phytec-phycore-som: Add initial support for PCM970 RDK
Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.
UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.
Dirk Behme [Thu, 16 May 2013 06:51:34 +0000 (08:51 +0200)]
i.MX6: Documentation: update from fsl,card-wired to non-removable
With the commit 7f217794f (mmc: dt: Consolidate DT bindings),
the device tree properties used by various device drivers
for SD/MMC host controllers were standardized. One of the changes
was that the property "fsl,card-wired", previously used by the
Freescale driver, was replaced with "non-removable". Fix the example
documentation regarding this.
ARM: imx: move imx53-qsb audio codec clk lookup into DT
With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.
Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.
Philipp Zabel [Tue, 9 Apr 2013 17:18:47 +0000 (19:18 +0200)]
ARM i.MX53: dts: add i2c aliases
This allows to order the i2c character devices correctly,
so that /dev/i2c-0 corresponds to i2c1, /dev/i2c-1 corresponds
to i2c2, and so on. Currently they are ordered by register
address.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Mon, 17 Jun 2013 08:02:51 +0000 (16:02 +0800)]
Merge tag 'imx-soc-3.11' into imx/dt
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
Markus Pargmann [Thu, 6 Jun 2013 12:41:57 +0000 (14:41 +0200)]
ARM: imx: Remove mxc specific ulpi access ops
There are ulpi access ops implemented in drivers/usb/phy/phy-ulpi.c.
mxc access ops implement the same access operations within mach-imx. This
patch removes the mxc ulpi file and uses phy-ulpi instead for
imx_otg_ulpi_create.
phy-ulpi successfully tested with i.MX27 Phytec phyCARD-S (pca100).
Jingchang Lu [Tue, 28 May 2013 09:12:20 +0000 (17:12 +0800)]
ARM: imx: add VF610 clock support
Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.
Signed-off-by: Jingchang Lu <b35083@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Tue, 21 May 2013 01:58:51 +0000 (09:58 +0800)]
ARM: imx6: use common of_clk_init() call to initialize clocks
Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.
Philipp Zabel [Fri, 17 May 2013 13:49:03 +0000 (15:49 +0200)]
ARM i.MX5: Add S/PDIF clocks
This patch adds the S/PDIF clocks for i.MX51 and i.MX53. Tested on i.MX53.
The i.MX51 has a second set of spdif_root clock dividers, and on i.MX53
there is an additional input to the spdif_xtal mux.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Jiada Wang [Fri, 17 May 2013 08:40:44 +0000 (17:40 +0900)]
ARM: imx: disable pll8_mlb in mx6q_clks
The MLB PLL clock's operation doesn't fit for clock framework and
it should be handled internally in MLB driver.
Remove initialization of pll8_mlb clock device but leave its
declaration in mx6q_clks to avoid affecting imx6q clock numbering.
Shawn Guo [Fri, 3 May 2013 03:06:46 +0000 (11:06 +0800)]
ARM: imx: add clock support for imx6sl
Add clock support for i.MX6 SoloLite. It uses the dtc marco support to
define all clock IDs in imx6sl-clock.h, which will be included by both
clock driver and device tree sources, so that the data will stay sync
all the time between kernel and DT.
Shawn Guo [Fri, 10 May 2013 02:19:01 +0000 (10:19 +0800)]
ARM: imx: create mxc_arch_reset_init_dt() for DT boot
The mxc_arch_reset_init() uses static mapping and calls clk_get_sys() to
get clock. It's suitable for non-DT boot but not for DT boot where
dynamic mapping and of_clk_get() should be used instead. Create
mxc_arch_reset_init_dt() as the DT variant of mxc_arch_reset_init(),
and change DT platforms to use it.
Shawn Guo [Fri, 10 May 2013 01:13:44 +0000 (09:13 +0800)]
ARM: imx: move clk_prepare() out from mxc_restart()
It's inappropriate to call clk_prepare() in mxc_restart(), because the
restart routine could be called in atomic context. Move clk_get() and
clk_prepare() into mxc_arch_reset_init() and only have the atomic part
clk_enable() be called in mxc_restart().
As a result, mxc_arch_reset_init() needs to be called after clk gets
initialized.
While there, it also changes printk(KERN_ERR ...) to pr_err() and adds
__init annotation for mxc_arch_reset_init().
Dirk Behme [Fri, 3 May 2013 09:08:45 +0000 (11:08 +0200)]
ARM: i.MX6: clk: add i.MX6 DualLite differences
The CCM_CBCMR register (address 0x02C4018) has different meaning
between the i.MX6 Quad/Dual and the i.MX6 Solo/DualLite.
Compared to the i.MX6 Quad/Dual, the CCM_CBCMR register in the
i.MX6 Solo/DualLite doesn't have a gpu3d_shader configuration and
moves the gpu2_core configuration at that place.
Handle these i.MX6 Quad/Dual vs. i.MX6 Solo/DualLite clock differences
by using cpu_is_mx6dl().
Martin Fuzzey [Tue, 23 Apr 2013 12:16:59 +0000 (20:16 +0800)]
ARM: i.MX5: Allow DT clock providers
Currently clock providers defined in the DT are not registered
on i.MX5 platforms since of_clk_init() is not called.
This is not a problem for the SOC's own clocks, which are registered
in code, but prevents the DT being used to define clocks for external
hardware.
Fix this by calling of_clk_init() and actually using the DT to obtain
the 4 SOC fixed clocks.
These are already defined in the DT but were previously just used to
manually obtain the rate.
Fall back to the old scheme for non DT platforms.
Since the same method may be useful for other i.MX platforms
implement the imx_obtain_fixed_clock() function in common code.
Actually changing other i.MX platforms to use this should be done
later by someone with access to the appropriate hardware.
Linus Torvalds [Sat, 15 Jun 2013 21:49:48 +0000 (11:49 -1000)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703
1) Fix RTNL locking in batman-adv, from Matthias Schiffer.
2) Don't allow non-passthrough macvlan devices to set NOPROMISC via
netlink, otherwise we can end up with corrupted promisc counter
values on the device. From Michael S Tsirkin.
3) Fix stmmac driver build with debugging defines enabled, from Dinh
Nguyen.
4) Make sure name string we give in socket address in AF_PACKET is NULL
terminated, from Daniel Borkmann.
5) Fix leaking of two uninitialized bytes of memory to userspace in
l2tp, from Guillaume Nault.
6) Clear IPCB(skb) before tunneling otherwise we touch dangling IP
options state and crash. From Saurabh Mohan.
7) Fix suspend/resume for davinci_mdio by using suspend_late and
resume_early. From Mugunthan V N.
8) Don't tag ip_tunnel_init_net and ip_tunnel_delete_net with
__net_{init,exit}, they can be called outside of those contexts.
From Eric Dumazet.
9) Fix RX length error in sh_eth driver, from Yoshihiro Shimoda.
10) Fix missing sctp_outq initialization in some code paths of SCTP
stack, from Neil Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
tulip: Properly check dma mapping result
net: sh_eth: fix incorrect RX length error if R8A7740
ip_tunnel: remove __net_init/exit from exported functions
drivers: net: davinci_mdio: restore mdio clk divider in mdio resume
drivers: net: davinci_mdio: moving mdio resume earlier than cpsw ethernet driver
net/ipv4: ip_vti clear skb cb before tunneling.
tg3: Wait for boot code to finish after power on
l2tp: Fix sendmsg() return value
l2tp: Fix PPP header erasure and memory leak
bonding: fix igmp_retrans type and two related races
bonding: reset master mac on first enslave failure
packet: packet_getname_spkt: make sure string is always 0-terminated
net: ethernet: stmicro: stmmac: Fix compile error when STMMAC_XMIT_DEBUG used
be2net: Fix 32-bit DMA Mask handling
xen-netback: don't de-reference vif pointer after having called xenvif_put()
macvlan: don't touch promisc without passthrough
batman-adv: Don't handle address updates when bla is disabled
batman-adv: forward late OGMs from best next hop
...
Linus Torvalds [Sat, 15 Jun 2013 05:25:04 +0000 (19:25 -1000)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"So here are 3 fixes still for 3.10. Fixes are simple, bugs are nasty
(though not recent regressions, nasty enough) and all targeted at
stable"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
David Daney [Fri, 14 Jun 2013 18:13:59 +0000 (11:13 -0700)]
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
Thanks to commit f91eb62f71b3 ("init: scream bloody murder if interrupts
are enabled too early"), "bloody murder" is now being screamed.
With a MIPS OCTEON config, we use on_each_cpu() in our
irq_chip.irq_bus_sync_unlock() function. This gets called in early as a
result of the time_init() call. Because the !SMP version of
on_each_cpu() unconditionally enables irqs, we get:
WARNING: at init/main.c:560 start_kernel+0x250/0x410()
Interrupts were enabled early
CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.0-rc5-Cavium-Octeon+ #801
Call Trace:
show_stack+0x68/0x80
warn_slowpath_common+0x78/0xb0
warn_slowpath_fmt+0x38/0x48
start_kernel+0x250/0x410
Suggested fix: Do what we already do in the SMP version of
on_each_cpu(), and use local_irq_save/local_irq_restore. Because we
need a flags variable, make it a static inline to avoid name space
issues.
[ Change from v1: Convert on_each_cpu to a static inline function, add
#include <linux/irqflags.h> to avoid build breakage on some files.
on_each_cpu_mask() and on_each_cpu_cond() suffer the same problem as
on_each_cpu(), but they are not causing !SMP bugs for me, so I will
defer changing them to a less urgent patch. ]
Signed-off-by: David Daney <david.daney@cavium.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>