of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC. Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage. Anyone wishing to use any of those modes
will have to modify the driver.
Tested on sh73a0-based kzm9g board. Only one mode has been tested and
is enabled. That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Acked-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 22 Feb 2013 00:43:53 +0000 (16:43 -0800)]
drivers/video/backlight/l4f00242t03.c: convert to devm_regulator_get()
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Jingoo Han <jg1.han@samsung.com> Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:51 +0000 (16:43 -0800)]
backlight: corgi_lcd: use lcd_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using lcd_device
instead of using dev_get_drvdata with &ld->dev, so we can directly pass a
struct lcd_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:50 +0000 (16:43 -0800)]
backlight: omap1: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:49 +0000 (16:43 -0800)]
backlight: tosa: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:48 +0000 (16:43 -0800)]
backlight: corgi_lcd: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:47 +0000 (16:43 -0800)]
backlight: ams369fg06: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:46 +0000 (16:43 -0800)]
pwm_backlight: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Cc: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:44 +0000 (16:43 -0800)]
backlight: aat2870: use bl_get_data instead of dev_get_drvdata
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:43 +0000 (16:43 -0800)]
backlight: lms501kf03: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:42 +0000 (16:43 -0800)]
backlight: corgi_lcd: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:41 +0000 (16:43 -0800)]
backlight: tosa: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:40 +0000 (16:43 -0800)]
backlight: vgg2432a4: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:39 +0000 (16:43 -0800)]
backlight: ams369fg06: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:38 +0000 (16:43 -0800)]
backlight: lms283gf05: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:37 +0000 (16:43 -0800)]
backlight: tdo24m: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:36 +0000 (16:43 -0800)]
backlight: ltv350qv: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:35 +0000 (16:43 -0800)]
backlight: s6e63m0: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:33 +0000 (16:43 -0800)]
backlight: ld9040: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:43:32 +0000 (16:43 -0800)]
backlight: l4f00242t03: use spi_get_drvdata and spi_set_drvdata
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'before_power' was used to check the previous status when resume() is
called. However, FB_BLANK_POWERDOWN was used in suspend() all the time,
so there is no need to check the previous status. Also, redundant return
variables are removed to reduce the code.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unnecessary NULL deference check, because it was already checked in
ams369fg06_probe(). Also, unnecessary parentheses are removed in
ams369fg06_power_is_on().
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'before_power' was used to check the previous status when resume() is
called. However, FB_BLANK_POWERDOWN was used in suspend() all the time,
so there is no need to check the previous status. Also, redundant return
variables are removed to reduce the code.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cody P Schafer [Fri, 22 Feb 2013 00:43:13 +0000 (16:43 -0800)]
MAINTAINERS: mm: add additional include files to listing
Add gfp.h, mmzone.h, memory_hotplug.h & vmalloc.h to the "MEMORY
MANAGMENT" section so scripts/get_maintainer.pl can do a better job of
making recommendations.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_maintainer.pl: find maintainers for removed files
For removed files, get_maintainer.pl doesn't find any maintainers (besides
the default linux-kernel@vger.kernel.org), as it only looks at the "+++"
lines, which are "/dev/null" for removals. Fix this by extending the
parsing to the "---" lines.
E.g. for the two line test patch below the real score maintainers will now
be found:
lib/vsprintf.c: add %pa format specifier for phys_addr_t types
Add the %pa format specifier for printing a phys_addr_t type and its
derivative types (such as resource_size_t), since the physical address
size on some platforms can vary based on build options, regardless of
the native integer type.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org> Cc: Rob Landley <rob@landley.net> Cc: George Spelvin <linux@horizon.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian Kujau [Fri, 22 Feb 2013 00:43:05 +0000 (16:43 -0800)]
sun.com documentation fixes
After I came across a help text for SUNGEM mentioning a broken sun.com
URL, I felt like fixing those up, as they are now pointing to oracle.com
URLs.
Signed-off-by: Christian Kujau <lists@nerdbynature.de> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Fri, 22 Feb 2013 00:43:03 +0000 (16:43 -0800)]
smp: make smp_call_function_many() use logic similar to smp_call_function_single()
I'm testing swapout workload in a two-socket Xeon machine. The workload
has 10 threads, each thread sequentially accesses separate memory
region. TLB flush overhead is very big in the workload. For each page,
page reclaim need move it from active lru list and then unmap it. Both
need a TLB flush. And this is a multthread workload, TLB flush happens
in 10 CPUs. In X86, TLB flush uses generic smp_call)function. So this
workload stress smp_call_function_many heavily.
swapout throughput is around 1400M/s. So there is around a 7%
improvement, and total cpu utilization doesn't change.
Without the patch, cfd_data is shared by all CPUs.
generic_smp_call_function_interrupt does read/write cfd_data several times
which will create a lot of cache ping-pong. With the patch, the data
becomes per-cpu. The ping-pong is avoided. And from the perf data, this
doesn't make call_single_queue lock contend.
Next step is to remove generic_smp_call_function_interrupt() from arch
code.
Signed-off-by: Shaohua Li <shli@fusionio.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the alpha arch_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
Signed-off-by: Michel Lespinasse <walken@google.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Fri, 22 Feb 2013 00:42:59 +0000 (16:42 -0800)]
ubifs: wait for page writeback to provide stable pages
When stable pages are required, we have to wait if the page is just
going to disk and we want to modify it. Add proper callback to
ubifs_vm_page_mkwrite().
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Cc: Artem Bityutskiy <dedekind1@gmail.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Fri, 22 Feb 2013 00:42:57 +0000 (16:42 -0800)]
ocfs2: wait for page writeback to provide stable pages
When stable pages are required, we have to wait if the page is just
going to disk and we want to modify it. Add proper callback to
ocfs2_grab_pages_for_write().
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Artem Bityutskiy <dedekind1@gmail.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 22 Feb 2013 00:42:55 +0000 (16:42 -0800)]
block: optionally snapshot page contents to provide stable pages during write
This provides a band-aid to provide stable page writes on jbd without
needing to backport the fixed locking and page writeback bit handling
schemes of jbd2. The band-aid works by using bounce buffers to snapshot
page contents instead of waiting.
For those wondering about the ext3 bandage -- fixing the jbd locking
(which was done as part of ext4dev years ago) is a lot of surgery, and
setting PG_writeback on data pages when we actually hold the page lock
dropped ext3 performance by nearly an order of magnitude. If we're
going to migrate iscsi and raid to use stable page writes, the
complaints about high latency will likely return. We might as well
centralize their page snapshotting thing to one place.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Tested-by: Andy Lutomirski <luto@amacapital.net> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Artem Bityutskiy <dedekind1@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 22 Feb 2013 00:42:53 +0000 (16:42 -0800)]
9pfs: fix filesystem to wait for stable page writeback
Fix up the ->page_mkwrite handler to provide stable page writes if necessary.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Artem Bityutskiy <dedekind1@gmail.com> Cc: Jan Kara <jack@suse.cz> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 22 Feb 2013 00:42:51 +0000 (16:42 -0800)]
mm: only enforce stable page writes if the backing device requires it
Create a helper function to check if a backing device requires stable
page writes and, if so, performs the necessary wait. Then, make it so
that all points in the memory manager that handle making pages writable
use the helper function. This should provide stable page write support
to most filesystems, while eliminating unnecessary waiting for devices
that don't require the feature.
Before this patchset, all filesystems would block, regardless of whether
or not it was necessary. ext3 would wait, but still generate occasional
checksum errors. The network filesystems were left to do their own
thing, so they'd wait too.
After this patchset, all the disk filesystems except ext3 and btrfs will
wait only if the hardware requires it. ext3 (if necessary) snapshots
pages instead of blocking, and btrfs provides its own bdi so the mm will
never wait. Network filesystems haven't been touched, so either they
provide their own stable page guarantees or they don't block at all.
The blocking behavior is back to what it was before 3.0 if you don't
have a disk requiring stable page writes.
Here's the result of using dbench to test latency on ext2:
Throughput 55.4496 MB/sec 4 clients 4 procs max_latency=298.650 ms
As you can see, the maximum write latency drops considerably with this
patch enabled. The other filesystems (ext3/ext4/xfs/btrfs) behave
similarly, but see the cover letter for those results.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Steven Whitehouse <swhiteho@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Artem Bityutskiy <dedekind1@gmail.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 22 Feb 2013 00:42:48 +0000 (16:42 -0800)]
bdi: allow block devices to say that they require stable page writes
This patchset ("stable page writes, part 2") makes some key
modifications to the original 'stable page writes' patchset. First, it
provides creators (devices and filesystems) of a backing_dev_info a flag
that declares whether or not it is necessary to ensure that page
contents cannot change during writeout. It is no longer assumed that
this is true of all devices (which was never true anyway). Second, the
flag is used to relaxed the wait_on_page_writeback calls so that wait
only occurs if the device needs it. Third, it fixes up the remaining
disk-backed filesystems to use this improved conditional-wait logic to
provide stable page writes on those filesystems.
It is hoped that (for people not using checksumming devices, anyway)
this patchset will give back unnecessary performance decreases since the
original stable page write patchset went into 3.0. Sorry about not
fixing it sooner.
Complaints were registered by several people about the long write
latencies introduced by the original stable page write patchset.
Generally speaking, the kernel ought to allocate as little extra memory
as possible to facilitate writeout, but for people who simply cannot
wait, a second page stability strategy is (re)introduced: snapshotting
page contents. The waiting behavior is still the default strategy; to
enable page snapshotting, a superblock flag (MS_SNAP_STABLE) must be
set. This flag is used to bandaid^Henable stable page writeback on
ext3[1], and is not used anywhere else.
Given that there are already a few storage devices and network FSes that
have rolled their own page stability wait/page snapshot code, it would
be nice to move towards consolidating all of these. It seems possible
that iscsi and raid5 may wish to use the new stable page write support
to enable zero-copy writeout.
Thank you to Jan Kara for helping fix a couple more filesystems.
Per Andrew Morton's request, here are the result of using dbench to measure
latencies on ext2:
Throughput 55.4496 MB/sec 4 clients 4 procs max_latency=298.650 ms
As you can see, for ext2 the maximum write latency decreases from ~60ms
on a laptop hard disk to ~4ms. I'm not sure why the flush latencies
increase, though I suspect that being able to dirty pages faster gives
the flusher more work to do.
On ext4, the average write latency decreases as well as all the maximum
latencies:
Throughput 34.0795 MB/sec 4 clients 4 procs max_latency=219.044 ms
Before this patchset, all filesystems would block, regardless of whether
or not it was necessary. ext3 would wait, but still generate occasional
checksum errors. The network filesystems were left to do their own
thing, so they'd wait too.
After this patchset, all the disk filesystems except ext3 and btrfs will
wait only if the hardware requires it. ext3 (if necessary) snapshots
pages instead of blocking, and btrfs provides its own bdi so the mm will
never wait. Network filesystems haven't been touched, so either they
provide their own wait code, or they don't block at all. The blocking
behavior is back to what it was before 3.0 if you don't have a disk
requiring stable page writes.
This patchset has been tested on 3.8.0-rc3 on x64 with ext3, ext4, and
xfs. I've spot-checked 3.8.0-rc4 and seem to be getting the same
results as -rc3.
[1] The alternative fixes to ext3 include fixing the locking order and
page bit handling like we did for ext4 (but then why not just use
ext4?), or setting PG_writeback so early that ext3 becomes extremely
slow. I tried that, but the number of write()s I could initiate dropped
by nearly an order of magnitude. That was a bit much even for the
author of the stable page series! :)
This patch:
Creates a per-backing-device flag that tracks whether or not pages must
be held immutable during writeout. Eventually it will be used to waive
wait_for_page_writeback() if nothing requires stable pages.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Artem Bityutskiy <dedekind1@gmail.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
which is clearly bogus. If lockdep is disabled in the config this would
cause a compile failure, if it is enabled then it compiles and causes a
puzzling warning about dereferencing without the correct protection.
Wrap the macro in "do { ... } while (0)" to also fail compile for this
when lockdep is enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill Tkhai [Fri, 22 Feb 2013 00:42:42 +0000 (16:42 -0800)]
scripts/tags.sh: add ctags magic for declarations of popular kernel type
- Add magic for declarations of variables of popular kernel type like
spinlock_t, list_head, wait_queue_head_t and other.
- Add a set of specially handled declaration extentions like
__attribute, __aligned and other.
- Simplify pci_bus_* magic
Signed-off-by: Kirill V Tkhai <tkhai@yandex.ru> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
How is the compiler even handling exported functions that are marked
inline? Anyway, these shouldn't be inline because of that, so remove
that marking.
Based on a larger patch by Mark Charlebois to get LLVM to build the
kernel.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Charlebois <mcharleb@qualcomm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: hank <pyu@redhat.com> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Fri, 22 Feb 2013 00:42:37 +0000 (16:42 -0800)]
video: exynos_dp: add missing of_node_put()
of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Jingoo Han [Fri, 22 Feb 2013 00:42:31 +0000 (16:42 -0800)]
video: s3c-fb: remove duplicated S3C_FB_MAX_WIN
S3C_FB_MAX_WIN is already defined in 'plat-samsung/include/plat/fb.h'.
So, this definition in 'include/video/samsung_fimd.h' should be removed to
avoid the duplication.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Tomasz Figa <t.figa@samsung.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhou Zhu [Fri, 22 Feb 2013 00:42:18 +0000 (16:42 -0800)]
video: mmpdisp: add spi port in display controller
Add spi port support in mmp display controller. This port is from display
controller and for panel usage. This driver implemented and registered as
a spi master.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Lisa Du <cldu@marvell.com> Cc: Guoqing Li <ligq@marvell.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lisa Du [Fri, 22 Feb 2013 00:42:17 +0000 (16:42 -0800)]
video: mmp: add tpo hvga panel supported
Add tpo hvga panel support in marvell display framework. This panel
driver implements modes query and power on/off.
This panel driver gets panel config/ plat power on/off/ connected path
name from machine-info and registered as a spi device. This panel
driver uses mmp_disp supplied register_panel function to register panel
to path as machine-info defined.
Signed-off-by: Lisa Du <cldu@marvell.com> Signed-off-by: Zhou Zhu <zzhu3@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Guoqing Li <ligq@marvell.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guoqing Li [Fri, 22 Feb 2013 00:42:15 +0000 (16:42 -0800)]
video: mmp display controller support
Marvell mmp series display controller support in mmpdisp subsystem.
This driver focus on implementation of hardware operations of
path/overlay, which is defined in mmp display subsystem interface. This
driver registers all pathes to mmp display framework.
Signed-off-by: Guoqing Li <ligq@marvell.com> Signed-off-by: Lisa Du <cldu@marvell.com> Signed-off-by: Zhou Zhu <zzhu3@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 22 Feb 2013 00:42:14 +0000 (16:42 -0800)]
fb: mmp: include linux/platform_device.h
Commit 16559ae48c76 ("kgdb: remove #include <linux/serial_8250.h> from
kgdb.h") changes the kgdb.h file so that drivers including it do not
implicitly include linux/platform_device.h. The mmp framebuffer driver
is new, so Greg did not have a chance to fix it up when introducing his
change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Zhou Zhu <zzhu3@marvell.com> Cc: Lisa Du <cldu@marvell.com> Cc: Guoqing Li <ligq@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhou Zhu [Fri, 22 Feb 2013 00:42:12 +0000 (16:42 -0800)]
video: mmp fb support
Add fb support for Marvell mmp display subsystem. This driver is
configured using "buffer driver mach info". With configured name of path,
this driver get path using using exported interface of mmp display driver.
Then this driver get overlay using configured id and operates on this
overlay to show buffers on display devices.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com> Signed-off-by: Lisa Du <cldu@marvell.com> Cc: Guoqing Li <ligq@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. fb folder contains implementation of fb. fb get path and overlay
from common interface and operates on these structures.
2. core.c provides common interface for a hardware abstraction. Major
parts of this interface are:
a) Path: path is a output device connected to a panel or HDMI TV. Main
operations of the path is set/get timing/output color. fb operates
output device through path structure.
b) Ovly: Ovly is a buffer shown on the path.
Ovly describes frame buffer and its source/destination size, offset,
input color, buffer address, z-order, and so on. Each fb device maps
to one overlay.
3. hw folder contains implementation of hardware operations defined by
core.c. It registers paths for fb use.
4. panel folder contains implementation of panels. It's connected to
path. Panel drivers would also regiester panels and linked to path
when probe.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com> Signed-off-by: Lisa Du <cldu@marvell.com> Cc: Guoqing Li <ligq@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arve Hjønnevåg [Fri, 22 Feb 2013 00:42:09 +0000 (16:42 -0800)]
goldfish: framebuffer driver
Framebuffer support for the Goldfish emulator. This takes the Google
emulator and applies the x86 cleanups as well as moving the blank
methods to the usual Linux place and dropping the Android early suspend
logic (for now at least, that can be looked at as Android and upstream
converge). Dropped various oddities like setting MTRRs on a virtual
frame buffer emulation...
With the drivers so far you can now boot a Linux initrd and have fun.
[sheng@linux.intel.com: cleaned up to handle x86]
[thomas.keel@intel.com: ported to 3.4]
[alan@linux.intel.com: cleaned up for style and 3.7, moved blank methods]
[akpm@linux-foundation.org: fix (silly) sparse warnings] Signed-off-by: Mike A. Chan <mikechan@google.com> Signed-off-by: Arve Hjønnevåg <arve@android.com> Signed-off-by: Sheng Yang <sheng@linux.intel.com> Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com> Signed-off-by: Xiaohui Xin <xiaohui.xin@intel.com> Signed-off-by: Jun Nakajima <jun.nakajima@intel.com> Signed-off-by: Bruce Beare <bruce.j.beare@intel.com> Signed-off-by: Tom Keel <thomas.keel@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pcmcia: move unbind/rebind into dev_pm_ops.complete
Move the device rebind procedures for cardbus devices from the pm.resume
into the pm.complete callback.
The reason for moving the code is: "[...] The PM code needs to send
suspend and resume messages to every device in the right order, and it
can't do that if new devices are being added at the same time. [...]"
However the situation really isn't quite that rigid. In particular,
adding new children during a resume callback shouldn't cause much of
problem because the children don't need to be resumed anyway (since they
were never suspended). On the other hand, if you do it you will get a
dev_warn() from the PM core, something like 'parent should not be
sleeping'.
Still, it is considered bad form and should be avoided if possible."
(Alan Stern's full comment about the topic can
be found here: <https://lkml.org/lkml/2012/7/10/254>)
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Greg KH <greg@kroah.com> Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On cris-linux-gcc, __SIZE_TYPE__ expands to "unsigned int", as
gcc-4.6.3-nolibc/cris-linux/lib/gcc/cris-linux/4.6.3/plugin/include/config/cris/linux.h
has
#define SIZE_TYPE "unsigned int"
Hence __kernel_size_t is also "unsigned int". But __kernel_ssize_t is
"long", which has a different base type, causing compiler warnings like:
fs/quota/quota_tree.c:372:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'ssize_t' [-Wformat]
To fix this, __kernel_ssize_t should be changed to "int". Hence cris can
just use the generic 32-bit versions from include/asm-generic/posix_types.h
for all size-related types.
MITSUNARI Shigeo [Fri, 22 Feb 2013 00:42:01 +0000 (16:42 -0800)]
fs/block_dev.c: page cache wrongly left invalidated after revalidate_disk()
We found that bdev->bd_invalidated was left set once revalidate_disk()
is called, which results in page cache flush every time that device is
open.
Specifically, we found this problem in MD block device. Once we resize
a MD device, mdadm --monitor periodically flush all page cache for that
device every 60 or 1000 seconds when it opens the device.
This bug lies since at least 3.2.0 till the latest kernel(3.6.2). Patch
is attached.
Jim Somerville [Fri, 22 Feb 2013 00:41:59 +0000 (16:41 -0800)]
inotify: remove broken mask checks causing unmount to be EINVAL
Running the command:
inotifywait -e unmount /mnt/disk
immediately aborts with a -EINVAL return code. This is however a valid
parameter. This abort occurs only if unmount is the sole event
parameter. If other event parameters are supplied, then the unmount
event wait will work.
The problem was introduced by commit 44b350fc23e ("inotify: Fix mask
checks"). In that commit, it states:
The mask checks in inotify_update_existing_watch() and
inotify_new_watch() are useless because inotify_arg_to_mask()
sets FS_IN_IGNORED and FS_EVENT_ON_CHILD bits anyway.
But instead of removing the useless checks, it did this:
mask = inotify_arg_to_mask(arg);
- if (unlikely(!mask))
+ if (unlikely(!(mask & IN_ALL_EVENTS)))
return -EINVAL;
The problem is that IN_ALL_EVENTS doesn't include IN_UNMOUNT, and other
parts of the code keep IN_UNMOUNT separate from IN_ALL_EVENTS. So the
check should be:
if (unlikely(!(mask & (IN_ALL_EVENTS | IN_UNMOUNT))))
But inotify_arg_to_mask(arg) always sets the IN_UNMOUNT bit in the mask
anyway, so the check is always going to pass and thus should simply be
removed. Also note that inotify_arg_to_mask completely controls what
mask bits get set from arg, there's no way for invalid bits to get
enabled there.
Lets fix it by simply removing the useless broken checks.
Signed-off-by: Jim Somerville <Jim.Somerville@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: John McCutchan <john@johnmccutchan.com> Cc: Robert Love <rlove@rlove.org> Cc: Eric Paris <eparis@parisplace.org> Cc: <stable@vger.kernel.org> [2.6.37+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce compiletime_assert to compiler.h, which moves the details of
how to break a build and emit an error message for a specific compiler
to the headers where these details should be. Following in the
tradition of the POSIX assert macro, compiletime_assert creates a
build-time error when the supplied condition is *false*.
Next, we add BUILD_BUG_ON_MSG to bug.h which simply wraps
compiletime_assert, inverting the logic, so that it fails when the
condition is *true*, consistent with the language "build bug on." This
macro allows you to specify the error message you want emitted when the
supplied condition is true.
Finally, we remove all other code from bug.h that mucks with these
details (BUILD_BUG & BUILD_BUG_ON), and have them all call
BUILD_BUG_ON_MSG. This not only reduces source code bloat, but also
prevents the possibility of code being changed for one macro and not for
the other (which was previously the case for BUILD_BUG and
BUILD_BUG_ON).
Since __compiletime_error_fallback is now only used in compiler.h, I'm
considering it a private macro and removing the double negation that's
now extraneous.
[akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David Rientjes <rientjes@google.com> Cc: Joe Perches <joe@perches.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Santos [Fri, 22 Feb 2013 00:41:54 +0000 (16:41 -0800)]
compiler.h, bug.h: prevent double error messages with BUILD_BUG{,_ON}
Prior to the introduction of __attribute__((error("msg"))) in gcc 4.3,
creating compile-time errors required a little trickery.
BUILD_BUG{,_ON} uses this attribute when available to generate
compile-time errors, but also uses the negative-sized array trick for
older compilers, resulting in two error messages in some cases. The
reason it's "some" cases is that as of gcc 4.4, the negative-sized array
will not create an error in some situations, like inline functions.
This patch replaces the negative-sized array code with the new
__compiletime_error_fallback() macro which expands to the same thing
unless the the error attribute is available, in which case it expands to
do{}while(0), resulting in exactly one compile-time error on all
versions of gcc.
Note that we are not changing the negative-sized array code for the
unoptimized version of BUILD_BUG_ON, since it has the potential to catch
problems that would be disabled in later versions of gcc were
__compiletime_error_fallback used. The reason is that that an
unoptimized build can't always remove calls to an error-attributed
function call (like we are using) that should effectively become dead
code if it were optimized. However, using a negative-sized array with a
similar value will not result in an false-positive (error). The only
caveat being that it will also fail to catch valid conditions, which we
should be expecting in an unoptimized build anyway.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David Rientjes <rientjes@google.com> Cc: Joe Perches <joe@perches.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Santos [Fri, 22 Feb 2013 00:41:52 +0000 (16:41 -0800)]
bug.h: make BUILD_BUG_ON generate compile-time error
Negative sized arrays wont create a compile-time error in some cases
starting with gcc 4.4 (e.g., inlined functions), but gcc 4.3 introduced
the error function attribute that will.
This patch modifies BUILD_BUG_ON to behave like BUILD_BUG already does,
using the error function attribute so that you don't have to build the
entire kernel to discover that you have a problem, and then enjoy trying
to track it down from a link-time error.
Also, we are only including asm/bug.h and then expecting that
linux/compiler.h will eventually be included to define __linktime_error
(used in BUILD_BUG_ON). This patch includes it directly for clarity and
to avoid the possibility of changes in <arch>/*/include/asm/bug.h being
changed or not including linux/compiler.h for some reason.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Acked-by: Borislav Petkov <bp@alien8.de> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Joe Perches <joe@perches.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Santos [Fri, 22 Feb 2013 00:41:45 +0000 (16:41 -0800)]
bug.h: prevent double evaulation of `condition' in BUILD_BUG_ON
When calling BUILD_BUG_ON in an optimized build using gcc 4.3 and later,
the condition will be evaulated twice, possibily with side-effects. This
patch eliminates that error.
[akpm@linux-foundation.org: tweak code layout] Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David Rientjes <rientjes@google.com> Cc: Joe Perches <joe@perches.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Santos [Fri, 22 Feb 2013 00:41:44 +0000 (16:41 -0800)]
bug.h: fix BUILD_BUG_ON macro in __CHECKER__
When __CHECKER__ is defined, we disable all of the BUILD_BUG.* macros.
However, both BUILD_BUG_ON_NOT_POWER_OF_2 and BUILD_BUG_ON was evaluating
to nothing in this case, and we want (0) since this is a function-like
macro that will be followed by a semicolon.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Acked-by: Borislav Petkov <bp@alien8.de> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Joe Perches <joe@perches.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__linktime_error() does the same thing as __compiletime_error() and is
only used in bug.h. Since the macro defines a function attribute that
will cause a failure at compile-time (not link-time), it makes more sense
to keep __compiletime_error(), which is also neatly mated with
__compiletime_warning().
Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Borislav Petkov <bp@alien8.de> Cc: Andi Kleen <ak@linux.intel.com> Cc: Joe Perches <joe@perches.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log