* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
drivers/media/usb/dvb-usb-v2/anysee.c: In function ‘anysee_frontend_attach’:
drivers/media/usb/dvb-usb-v2/anysee.c:641: warning: ‘ret’ may be used uninitialized in this function
And gcc is right (see the ANYSEE_HW_507T case), so initialize ret to zero
to fix this.
[media] media: videobuf2: fix the length check for mmap
Memory maps typically require that the buffer size to be page
aligned. Currently, two memops drivers do such alignment
internally, but videobuf-vmalloc doesn't.
Also, the buffer overflow check doesn't take it into account.
So, instead of doing it at each memops driver, enforce it at
VB2 core.
Frank Schaefer [Mon, 8 Apr 2013 16:06:59 +0000 (13:06 -0300)]
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 17 Apr 2013 06:04:10 +0000 (03:04 -0300)]
[media] mem2mem_testdev: set timestamp_type and add debug param
While testing v4l2-ctl I noticed that this m2m driver didn't set timestamp_type
and that it spammed the kernel log with debug messages. Set timestamp_type
correctly and add debug module option to enable debug messages.
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
[media] m2m-deinterlace: Add copy time stamp handling
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
[media] exynos4-is: Copy timestamps from M2M OUTPUT to CAPTURE buffer queue
Add copying of buffer timestamps and set the timestamp_type to
V4L2_BUF_FLAG_TIMESTAMP_COPY to avoid warnings about UNDEFINED
timestamp type like:
WARNING: at drivers/media/v4l2-core/videobuf2-core.c:2042 vb2_queue_init+0xe0/0x18c()
Modules linked in:
[<c0016ef0>] (unwind_backtrace+0x0/0x13c) from [<c0029b3c>] (warn_slowpath_common+0x54/0x64)
[<c0029b3c>] (warn_slowpath_common+0x54/0x64) from [<c0029b68>] (warn_slowpath_null+0x1c/0x24)
[<c0029b68>] (warn_slowpath_null+0x1c/0x24) from [<c03b7018>] (vb2_queue_init+0xe0/0x18c)
[<c03b7018>] (vb2_queue_init+0xe0/0x18c) from [<c03b4e08>] (v4l2_m2m_ctx_init+0xa0/0xc4)
[<c03b4e08>] (v4l2_m2m_ctx_init+0xa0/0xc4) from [<c03ca6c4>] (fimc_m2m_open+0x130/0x1f8)
[<c03ca6c4>] (fimc_m2m_open+0x130/0x1f8) from [<c03a5dd4>] (v4l2_open+0xac/0xe8)
[<c03a5dd4>] (v4l2_open+0xac/0xe8) from [<c0113920>] (chrdev_open+0x9c/0x158)
[<c0113920>] (chrdev_open+0x9c/0x158) from [<c010e488>] (do_dentry_open+0x1f8/0x280)
[<c010e488>] (do_dentry_open+0x1f8/0x280) from [<c010e600>] (finish_open+0x34/0x50)
[<c010e600>] (finish_open+0x34/0x50) from [<c011cc58>] (do_last+0x5bc/0xc00)
[<c011cc58>] (do_last+0x5bc/0xc00) from [<c011d34c>] (path_openat+0xb0/0x484)
[<c011d34c>] (path_openat+0xb0/0x484) from [<c011d824>] (do_filp_open+0x30/0x84)
[<c011d824>] (do_filp_open+0x30/0x84) from [<c010e0f8>] (do_sys_open+0xe8/0x170)
[<c010e0f8>] (do_sys_open+0xe8/0x170) from [<c000f040>] (ret_fast_syscall+0x0/0x30)
[media] exynos4-is: Fix TRY format propagation at MIPI-CSIS subdev
Ensure TRY format is propagated from the sink to source pad.
The format at both pads is always same so the TRY format buffer
for pad 0 is used to hold format for both pads.
While at it remove redundant fmt->pad checking.
[media] exynos4-is: Fix driver name reported in vidioc_querycap
Originally struct v4l2_capability driver and card name was filled
with name of the platform device. After switching to the device tree
the device names have changed and now are 4 different driver names
reported, depending on the video device opened. So instead of e.g.
"exynos4-fimc" there is now one of: 11800000.fimc, 11810000.fimc, 11820000.fimc, 11830000.fimc.
Fix this by using dev->driver_name, rather than platform device name.
A common vidioc_querycap function is created for both M2M and capture
video node.
This fixes any breakage at user space should any application/library
rely on the driver's name.
[media] exynos4-is: Remove redundant module_put() for MIPI-CSIS module
Currently there is unbalanced module_put() on the s5p-csis module
which prevents it from being unloaded. The subdev's owner module
has reference count decremented in v4l2_device_unregister_subdev()
so just remove this erroneous call.
[media] exynos4-is: Set fimc-lite subdev owner module
The FIMC-LITE.n subdevs have currently sd->owner field not set,
the exynos-fimc-lite module can be removed at any time, regardless
it is in use by other modules. When this module is unloaded the
kernel can crash easily by accessing video or media device nodes.
[media] exynos4-is: Unregister fimc-is subdevs from the media device properly
Add missing v4l2_device_unregister_subdev() call for the FIMC-IS subdevs
(currently there is only the FIMC-IS-ISP subdev) so corresponding resources
are properly freed upon the media device driver module removal.
[media] exynos4-is: Don't overwrite subdevdata in the fimc-is sensor driver
It's an I2C client driver and it must not overwrite the struct v4l2_subdev
dev_priv field, which is used by the v4l2 core to store a pointer to
struct i2c_client.
[media] exynos4-is: Fix regulator/gpio resource releasing on the driver removal
Remove regulator_bulk_free() calls as devm_regulator_bulk_get() function
is used to get the regulators so those will be freed automatically while
the driver is removed.
Missing gpio free is fixed by requesting a gpio with the devm_* API.
All that is done now in the I2C client driver remove() callback is the
media entity cleanup call.
Remove unneeded MODULE_DEVICE_TABLE(of,...) instances from files that
are linked into same module. This fixes following error when building
as a module:
LD [M] drivers/media/platform/exynos4-is/s5p-fimc.o
drivers/media/platform/exynos4-is/fimc-is-sensor.o: In function `.LANCHOR1':
fimc-is-sensor.c:(.rodata+0x48): multiple definition of `__mod_of_device_table'
drivers/media/platform/exynos4-is/fimc-is.o:fimc-is.c:(.rodata+0x174): first defined here
drivers/media/platform/exynos4-is/fimc-is-i2c.o:(.rodata+0x5c): multiple definition of `__mod_of_device_table'
drivers/media/platform/exynos4-is/fimc-is.o:fimc-is.c:(.rodata+0x174): first defined here
make[4]: *** [drivers/media/platform/exynos4-is/exynos-fimc-is.o] Error 1
Also remove exporting fimc_is_(un)register_i2c_driver functions, it
is not needed since these functions should be called only from our
module.
Kevin Baradon [Mon, 22 Apr 2013 19:09:44 +0000 (16:09 -0300)]
[media] imon: Use large delays earlier
send_packet() is used during initialization, before send_packet_delay
is set. So, move ictx->send_packet_delay to happen earlier.
[mchehab@redhat.com: fold two patches into one to make git history clearer] Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Olivier Grenie [Mon, 31 Dec 2012 12:51:17 +0000 (09:51 -0300)]
[media] dib7090p: improve the support of the dib7090 and dib7790
The intend of this patch is to improve the support of the dib7090 and
dib7790. The AGC1 min value is set to 32768 by default. The actual AGC1 min
and the external attenuation are controled depending on the received RF
level.
Olivier Grenie [Mon, 31 Dec 2012 12:47:10 +0000 (09:47 -0300)]
[media] dib7090p: remove the support for the dib7090E
The intend of this patch is to remove the support for the dib7090E. The
DiB7090E-package has never left prototype state and never made it to
mass-prod-state.
Olivier Grenie [Mon, 31 Dec 2012 13:17:44 +0000 (10:17 -0300)]
[media] dib8096: enhancement
The intend of this patch is to improve the support of the dib8096. The PLL
parameters are not automatically computed. The limit to set/unset external
diode for attenuation has been updated. The TFE8096P board is using the
new I2C API.
Olivier Grenie [Mon, 31 Dec 2012 13:38:44 +0000 (10:38 -0300)]
[media] dib0090: enhancement
The intend of this patch is to improve the support of the dib0090 tuner.
The ramp tables have been updated. Also some minor enhancements has been
added (EFUSE and reset).
Olivier Grenie [Mon, 31 Dec 2012 12:23:26 +0000 (09:23 -0300)]
[media] dib7000p: enhancement
The intend of this patch is to improve the support of the dib7000p. It is
now possible to set the minimum value for the AGC1. Also, the driver takes
into account the frequency offset introduced in the tuned frequency.
Dan Carpenter [Wed, 17 Apr 2013 06:20:30 +0000 (03:20 -0300)]
[media] go7007: dubious one-bit signed bitfields
Because they're signed, "is_video" and "is_audio" can be 0 and -1
instead of 0 and 1 as intended. It doesn't cause a bug, but it makes
Sparse complain:
drivers/staging/media/go7007/go7007-priv.h:94:31: error: dubious one-bit signed bitfield
drivers/staging/media/go7007/go7007-priv.h:95:31: error: dubious one-bit signed bitfield
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] cx88: Fix unsafe locking in suspend-resume
Legacy PCI suspend-resume handlers are called with interrupts enabled.
But cx8800_suspend/cx8800_resume and
cx8802_suspend_common/cx8802_resume_common use spin_lock/spin_unlock
functions to acquire dev->slock, while the same lock is acquired in the
corresponding irq-handlers: cx8800_irq and cx8802_irq.
That means a deadlock is possible if an interrupt happens while suspend
or resume owns the lock. The patch replaces spin_lock/spin_unlock with
spin_lock_irqsave/spin_unlock_irqrestore.
Found by Linux Driver Verification project (linuxtesting.org).
This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
[mchehab@redhat.com: change it to depends on MFD_SI476X_CORE instead of
selecting it; vidioc_s_register now uses const struct] Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] DT: export of_get_next_parent() for use by modules: fix modular V4L2
Currently modular V4L2 build with enabled OF is broken dur to the
of_get_next_parent() function being unavailable to modules. Export it to
fix the build.
There are a few errors at the PLL calculus, causing the device
to use wrong values.
While here, change the calculus to use 32 bits, as there's no
need for 64 bits there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
The rtl-sdr library disabled IMR callibration. While I'm not sure
yet why, it could be a good idea to add a modprobe parameter here,
to allow to also disable it. There are two rationale behind it:
- It helps to compare USB dumps between rtl-sdr and the Kernel module;
- If rtl-sdr disabled it, perhaps there's a good reason (e. g. it
might not be actually working, or it might be causing some trouble).
For both cases, it seems useful to add a modprobe parameter to allow
testing the device with both configurations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
Add the code to set the GPIO for this tuner. This code is
currently unused, so it is kept there only for completeness.
With this patch there are just two things that got left from
the original driver:
- At standby, there's another mode, not used by rtl2832u.
Not sure if it might be needed in the future, but I suspect
it is not used at all;
- There is a "fast tune" mode. As nor DVB or V4L API supports
it, it seems an overkill to implement it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
This code seems to calibrate I/Q phase and gain during the
device initialization.
This is done only once, and it doesn't seem to be needed to
happen after resuming.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
The rtl-sdr library, from where this driver was initially
based, doesn't use half PLL clock, but this is used on
the Realtek Kernel driver. So, also do the same here.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
This tuner works with 2 modes: automatic gain mode and manual
gain mode. Put it into automatic mode, as we currently don't
have any API for manual gain adjustment.
The logic to allow setting the manual mode is there, as it is
just a few extra code. This way, if/when we latter add support
for setting the gain mode, the code is already there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
[media] r820t: Add a tuner driver for Rafael Micro R820T silicon tuner
This driver was written from scratch, based on an existing driver
that it is part of rtl-sdr git tree, released under GPLv2:
https://groups.google.com/forum/#!topic/ultra-cheap-sdr/Y3rBEOFtHug
https://github.com/n1gp/gr-baz
http://cgit.osmocom.org/rtl-sdr/plain/src/tuner_r820t.c
(there are also other variants of it out there)
>From what I understood from the threads, the original driver was converted
to userspace from a Realtek tree. I couldn't find the original tree.
However, the original driver look awkward on my eyes. So, I decided to
write a new version from it from the scratch, while trying to reproduce
everything found there.
TODO:
- After locking, the original driver seems to have some routines to
improve reception. This was not implemented here yet.
- RF Gain set/get is not implemented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Antti Palosaari <crope@iki.fi>
[media] sta2x11_vip: Fix compilation if I2C is not set
From Fengguang Wu <fengguang.wu@intel.com>:
> drivers/media/pci/sta2x11/sta2x11_vip.c: In function 'sta2x11_vip_init_one':
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:2: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:15: warning: assignment makes pointer from integer without a cast [enabled by default]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1330:2: error: implicit declaration of function 'i2c_put_adapter' [-Werror=implicit-function-declaration]
And also:
> warning: (STA2X11_VIP) selects VIDEO_ADV7180 which has unmet direct dependencies (MEDIA_SUPPORT && VIDEO_V4L2 && I2C)
> drivers/media/i2c/adv7180.c: In function '__adv7180_status':
> drivers/media/i2c/adv7180.c:194:2: error: implicit declaration of function 'i2c_smbus_read_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_s_routing':
> drivers/media/i2c/adv7180.c:251:2: error: implicit declaration of function 'i2c_smbus_write_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_probe':
> drivers/media/i2c/adv7180.c:551:2: error: implicit declaration of function 'i2c_check_functionality' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c:554:2: error: implicit declaration of function 'i2c_adapter_id' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: At top level:
> drivers/media/i2c/adv7180.c:663:1: warning: data definition has no type or storage class [enabled by default]
> drivers/media/i2c/adv7180.c:663:1: warning: type defaults to 'int' in declaration of 'module_i2c_driver' [-Wimplicit-int]
> drivers/media/i2c/adv7180.c:663:1: warning: parameter names (without types) in function declaration [enabled by default]
> drivers/media/i2c/adv7180.c:649:26: warning: 'adv7180_driver' defined but not used [-Wunused-variable]
[media] it913x: rename its tuner driver to tuner_it913x
There are three drivers with *it913x name on it, and they all
belong to the same device:
a tuner, at it913x.c;
a frontend: it913x-fe.c;
a bridge: it913x.c, renamed to dvb_usb_it913x by the
building system.
This is confusing. Even more confusing are the two .c files with
the same name under different directories, with different contents
and different functions. So, prepend the tuner one.
This also breaks the out-of-tree compilation system.
Reported-by: Frederic Fays <frederic.fays@gmail.com> Acked-by: Antti Palosaari <crope@iki.fi> Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix mceusb_cmdsize() which returns incorrect datasize=0 for
sub-commands MCE_RSP_GETPORTSTATUS, MCE_RSP_GETWAKESOURCE,
MCE_RSP_EQDEVDETAILS, MCE_RSP_EQEMVER, and MCE_RSP_EQIRNUMPORTS.
While here, change mceusb_cmdsize() name to reflect that it returns
data size not cmd size.
Signed-off-by: William Steidtmann <billstei@hbci.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap [Tue, 16 Apr 2013 14:33:22 +0000 (11:33 -0300)]
[media] staging/media: fix go7007 dependencies and build
VIDEO_GO7007 uses usb interfaces so it should depend on USB.
It also selects CYPRESS_FIRMWARE, which depends on USB.
Fixes build errors and a kconfig warning:
go7007-loader.c:(.text+0xcc7d0): undefined reference to `usb_get_dev'
go7007-loader.c:(.init.text+0x49f0): undefined reference to `usb_register_driver'
go7007-loader.c:(.exit.text+0x17ce): undefined reference to `usb_deregister'
warning: (DVB_USB_AZ6007 && VIDEO_GO7007) selects CYPRESS_FIRMWARE which has unmet direct dependencies (MEDIA_SUPPORT && USB)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michal Marek [Tue, 16 Apr 2013 11:06:30 +0000 (08:06 -0300)]
[media] em28xx: Put remaining .vidioc_g_chip_info instance under ADV_DEBUG
Commit cd634f1 ("[media] v4l2: put VIDIOC_DBG_G_CHIP_NAME under
ADV_DEBUG") missed the initializer of radio_ioctl_ops:
drivers/media/usb/em28xx/em28xx-video.c:1830:2: error: unknown field 'vidioc_g_chip_info' specified in initializer
drivers/media/usb/em28xx/em28xx-video.c:1830:26: error: 'vidioc_g_chip_info' undeclared here (not in a function)
Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 14 Apr 2013 15:10:32 +0000 (12:10 -0300)]
[media] cx25821: drop cx25821-video-upstream-ch2.c/h
cx25821-video-upstream_ch2.c/h is practically identical to cx25821-video-upstream.c/h
so add support for ch2 into cx25821-video-upstream.c instead.
After this we can replace the custom ioctls with a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / karo-tx-linux.git / log