ath6kl: handle probe response from P2P device in P2P GO mode
When the device is in P2P GO mode and in listen state, the correct behavior is
to see two different probe response frames - one from P2P device and the other
from GO. wpa_supplicant uses the same mechanism to send the frame in both cases
(ath6kl_mgmt_tx). For GO probe response, ath6kl needs to call
ath6kl_send_go_probe_resp (this will add only WSC/P2P IEs and the rest of the
IEs are filled in by the firmware). That was done based on the nw_type ==
AP_NETWORK which would work if P2P Device role were in a separate netdev. When
P2P Device and GO use the same netdev, ath6kl needs to use the special GO probe
response case only if SSID is longer than P2P wildcard SSID.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com> Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Mon, 12 Mar 2012 11:22:54 +0000 (13:22 +0200)]
ath6kl: fix regression in ath6kl_upload_board_file()
My patch 24fc32b3 ("ath6kl: add ath6kl_bmi_write_hi32()") caused a regression
in ath6kl_upload_board_file() and the board_address variable was not
properly initialised in some cases:
ath6kl/init.c:1068:6: warning: ‘board_address’ may be used uninitialized
in this function
Most likely this broke ar6004 support but I can't test that right now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Portion of the commit id 080eec4fb4 ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.
kvalo: more details to the commit log
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Wed, 7 Mar 2012 18:04:00 +0000 (20:04 +0200)]
ath6kl: fix too long lines
Found by checkpatch:
drivers/net/wireless/ath/ath6kl/init.c:78: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/init.c:397: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/init.c:407: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:189: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:704: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:2452: WARNING: line over 80 characters
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error handling in ath6kl_target_config_wlan_params() was just weird,
fix that. This also fixes some of the open parenthesis alignment issues
reported by checkpatch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Wed, 7 Mar 2012 18:03:59 +0000 (20:03 +0200)]
ath6kl: add ath6kl_bmi_read_hi32()
There are few 32 bit reads from the host interest area. Add
ath6kl_bmi_read_hi32() to make it easier to do that. As code is cleaner
this also fixes few checkpatch warnings.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Wed, 7 Mar 2012 18:03:58 +0000 (20:03 +0200)]
ath6kl: remove multiple assignments
Found by checkpatch:
drivers/net/wireless/ath/ath6kl/cfg80211.c:1295: CHECK: multiple assignments should be avoided
drivers/net/wireless/ath/ath6kl/cfg80211.c:3000: CHECK: multiple assignments should be avoided
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 20 Feb 2012 13:38:08 +0000 (19:08 +0530)]
ath6kl: Set optimal listen intvl,bmiss,scan params while going to wow suspend
* In order to save the target power in WOW suspend state,
configure the best optimal values for the below parameters,
- listen interval.
- beacon miss interval.
- scan parameters.
Default values for above attributes are reverted in
wow resume operation.
* The default listen interval is set before the host issue
connect request.
* New function is added to configure beacon miss count.
kvalo: minor changes to fix open parenthesis alignment
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 20 Feb 2012 13:38:07 +0000 (19:08 +0530)]
ath6kl: Maintain the listen interval per VIF specific
Firmware has the option to support the listen interval
per vif specific. Fix this.
Listen interval can be set by the TUs or by the number
of beacons. Current code enables the user to configure
the listen interval in the unit of 'number of beacons'
using debugfs entry "listen_interval". Going forward,
we need to alter the listen interval in the unit of TUs
to get good power numbers while going to WOW suspend/resume.
Allowing the user to change the listen interval in
the unit of "number of beacons" in debugfs and changing
listen interval in wow suspend/resume in the unit of
time (TUs) would lead us to confuse.
This patch make sures the listen interval is changed only
in the unit of time (TUs).
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Wed, 7 Mar 2012 06:05:04 +0000 (11:35 +0530)]
ath6kl: Check wow state before sending control and data pkt
Below two scenarios are taken care in this patch which helped
to fix the firmware crash during wow suspend/resume.
* TX operation (ctrl tx and data tx) has to be controlled based
on suspend state. i.e, with respect to WOW mode, control packets
are allowed to send from the host until the suspend state goes
ATH6KL_STATE_WOW and the data packets are allowed until WOW
suspend operation starts.
* Similarly, wow resume is NOT allowed if WOW suspend is in progress.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Tue, 6 Mar 2012 09:33:59 +0000 (15:03 +0530)]
ath6kl: Add provision to define suspend policy in disconnected state.
It gives flexibility to the user to define suspend policy
when the suspend mode is set to WOW and the device is in
disconnected state at the time of suspend.
New module parameter wow_mode is added to get the choice
from the user. This parameter is valid only if the module
parameter suspend_mode is set to WOW.
To force WOW in connected state and cut power
in disconnected state:
suspend_mode=0x3 wow_mode=0x1
To force WOW in connected state and deep sleep
in disconnected state (this is also the default wow_mode):
suspend_mode=0x3 wow_mode=0x2
If there is no value specified to wow_mode during insmod,
deep sleep mode will be tried in the disconnected state.
kvalo: clarified commit log
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Fix kernel panic while receiving fwlog during boot
"ath6kl: Defer wiphy and netdev registration till the end of ath6kl_core_init()"
causes kernel panic by accessing the unallocated debug resources during
boot time. To fix this, split the debug initialization funtion into two,
one initializes the debug resource and the other takes care of debugfs
initialization. When this issue shows up the kernel crash dump would
look like
kvalo: rename new function to ath6kl_debug_init_fs() and add a comment
why it's needed
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Thu, 9 Feb 2012 07:27:12 +0000 (12:57 +0530)]
ath6kl: Fix random system lockup
The commit "ath6kl: Use a mutex_lock to avoid
race in diabling and handling irq" introduces a
state where ath6kl_sdio_irq_handler() would be waiting
to claim the sdio function for receive indefinitely
when things happen in the following order.
ath6kl_sdio_irq_handler()
- aquires mtx_irq
- sdio_release_host()
ath6kl_sdio_irq_disable()
- sdio_claim_host()
- sleep on mtx_irq
ath6kl_hif_intr_bh_handler()
- (indefinitely) wait for the sdio
function to be released to exclusively claim
it again for receive operation.
Fix this by replacing the mtx_irq with an atomic
variable and a wait_queue.
kvalo: add ath6kl_sdio_is_on_irq() due to open parenthesis alignment
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Etay Luz [Wed, 29 Feb 2012 01:18:04 +0000 (17:18 -0800)]
ath6kl: Collect residue firmware logs
Collect residue firmware logs following firmware assert.
Firmware sends logs to host once the 1500 byte log buffer
has been filled. At time of assert, there could be residue
logs lying in the firmware. This patch pulls those residue
logs. This would give the full picture of the firmware.
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove check so that IE in firmware is cleared if not set. Without this fix, any
previously set IE will be used incorrectly in the next frame. For example,
consider the scenario where a P2P device scan is followed by a regular station
scan. The P2P IE set by the P2P scan needs to be cleared, otherwise the station
scan will contain the P2P IE.
kvalo: indentation fixes
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Defer wiphy and netdev registration till the end of ath6kl_core_init()
This makes the wiphy and initial netdev registration the last step
in dev initialization. Apart from the fact that this looks right,
it can also be used to setup wiphy with the regulatory information
received from firmware after uploading the firmware. Also it fixes
a FIXME in ath6kl_core_init() where mac address is copied into
netdev->dev_addr, ath6kl_interface_add() takes care of this as well.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Skip vif index validation in ath6kl_rx() for wmi events
When the wmi event is vif specific, the validation of vif index
is taken care in ath6kl_wmi_proc_events_iface(). This also avoids
the need for a netdev to be registered while receiving initial events
like "target_ready" and "regulatory domain".
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wmi event processing into the one which needs to be
vif specific and the reset. This is a step towards avoiding
the need for wiphy and a netdev registration before getting
any message from firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville [Wed, 29 Feb 2012 20:08:33 +0000 (15:08 -0500)]
carl9170: fix breakage from "mac80211: handle non-bufferable MMPDUs correctly"
That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as
IEEE80211_TX_CTL_NO_PS_BUFFER. Meanwhile, "carl9170: fix frame delivery
if sta is in powersave mode" added a reference to
IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3. This simple
patch fixes that merge boo-boo.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Mon, 27 Feb 2012 11:52:06 +0000 (12:52 +0100)]
ath9k: decouple RX error checking for DFS
Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.
This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Mon, 27 Feb 2012 18:25:32 +0000 (12:25 -0600)]
iwlegacy: remove enum iw_calib and related code
Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX.
Remove the function il4965_calib_free_results. It was doing nothing
because IL_CALIB_MAX is zero. Next, remove calib_results from the
il_priv structure and also remove the associated return
type/struct il_calib_result.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Mon, 27 Feb 2012 18:25:31 +0000 (12:25 -0600)]
iwlegacy: Kconfig: Change Debug Option to be more clear
Since the menuconfig system doesn't indent the debug options
for the 3945 /4965, add some text to make it clear which
debug options are being configured.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 27 Feb 2012 11:18:30 +0000 (12:18 +0100)]
mac80211: handle non-bufferable MMPDUs correctly
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of defining an 'enum', we can simply use 'u8' flag for WEP
status. Rename 'wep_status' to 'wep_enabled' to match with
'wpa_enabled' and 'wpa2_enabled'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 25 Feb 2012 05:35:36 +0000 (21:35 -0800)]
mwifiex: remove redundant scan operation
It should have been removed by commit "mwifiex: use cfg80211 dynamic
scan..." (7c6fa2a843..) after adding code to avoid an extra scan
during association because scan entries are valid for 15 seconds in
cfg80211 stack.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Feb 2012 12:50:54 +0000 (13:50 +0100)]
mac80211: make deauth/disassoc sequence more natural
The association sequence looks (roughly) like
this now:
* set BSSID
* set station to EXIST state
* send auth
* set station to AUTH state
* send assoc
* set station to ASSOC state
* set BSS info to associated
In contrast, the deauth/disassoc sequence is
the other way around:
* clear BSSID/BSS info state
* remove station
* send deauth/disassoc
(in some cases the last two steps are reversed.)
This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
* send deauth/disassoc
* flush
* remove station
* clear BSSID/BSS info state
At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Feb 2012 12:50:52 +0000 (13:50 +0100)]
mac80211: dont call cfg80211 from ieee80211_send_deauth_disassoc
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Feb 2012 12:50:51 +0000 (13:50 +0100)]
cfg80211: remove cookies from callbacks
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
A second ifconfig wlan0 up brings the interface up without problems.
After a bit more debugging, the call trace is the following:
[10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error
ioread32(CR_REG1): -110
[10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs
[10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on
Adding a 10 milliseconds delay between the call to set_mc_hash() and
zd_chip_switch_radio_on() allows successful interface bringups in all
cases and matches what the vendor driver did.
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 25 Feb 2012 05:35:35 +0000 (21:35 -0800)]
mwifiex: reset encryption mode flag before association
Recent commit
"mwifiex: clear previous security setting during association"
fixes association failure problems observed in some corner cases
by clearing previous security setting before each association.
We should reset encryption mode flag as well. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: fix frame delivery if sta is in powersave mode
Nicolas Cavallari discovered that carl9170 has some
serious problems delivering data to sleeping stations.
It turns out that the driver was not honoring two
important flags (IEEE80211_TX_CTL_POLL_RESPONSE and
IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on
frames that should be sent although the receiving
station is still in powersave mode.
Cc: stable <stable@vger.kernel.org> Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: Fix memory accounting when sta is in power-save mode.
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory. Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.
This undo the allocation done in the TX path when the station is in
power-save mode.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Raja Mani [Wed, 22 Feb 2012 06:33:51 +0000 (12:03 +0530)]
ath6kl: Lower SDIO pad drive strength for hw2.1.1 board
Without this change, SDIO shuts down due to CRC error during
data communication to the firmware in some of the platform.
for example, scan request issued to the firmware doesn't
return scan completed events and cause the socket interface
to always return -16 (device busy).
SDIO pad drive strength should be reduced for hw2.1.1 board
to avoid such errors.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes the device get into scan state as soon as a
scan request is received, instead of blocking the scan
request till the traffic comes down. It is necessary
for the deterministic foreground scan particularly when
having multiple vif operating where, if the scan is non-
deterministic, scan on one interface will not start
as long as there are traffic on the other interface. This
change passes 50 msec as foreground scan interval to fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Fix memory leak of rx packets in endpoint 0
htc_packet and htc_packet->buf_start are separately allocated
for endpoint 0. This is different for other endpoints where
packets are allocated as skb where htc_packet is skb->head
and they are freed properly. Free htc_packet and htc_packet->buf_start
separatly for endpoint 0.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Make sure to allocate rx buffers after the endpoint connection
Rx buffers should be allocated for control and best effort endpoints only
after the enpoints connection is esablished. But this is done before the
endpoint connection is complete, we don't even the control and BE endpoints
that time. Move the buffer allocation after endpoint connection is over,
after ath6kl_init_hw_start(). Found in review, never seen any real issue
with this.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This handler allows the transport layer to free an skb from the
op_mode. This can happen when the driver is stopped while Tx
packets are pending in the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Define the op_mode as an interface with its ops. All the functions
of the op_mode are "private", but its ops is made public in
iwl-op-mode.h.
The drv object starts the op_mode by using the start function in the
public ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: rename iwl_remove to iwl_op_mode_dvm_stop
iwl_remove stops the wifi flows, so rename.
Moreover, we can possibly stop the wifi flows even if the driver
is statically compiled in the kernel, so remove the __devexit pragma.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fetch the fw and spawn the op_mode. The op_mode that we need
to fetch is determined from the fw file.
Since the fw is fetched very early in the init flow, we can
determine what op_mode to spawn.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Tue, 21 Feb 2012 16:31:06 +0000 (18:31 +0200)]
iwlwifi: move uCode flags handling to op_mode
The uCode flags modification is op_mode dependent
since the P2P config is an op-mode config.
This also fixes P2P enabling: due to the uCode
loading code shuffle moving the SKU check before
the EEPROM was read it was always false and would
always disable PAN/P2P.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: move content of iwl_probe to post fetch_fw
This will allow to have different behavior depending on the fw.
Different fw APIs require completely different implementation
of the mac80211 APIs. Each of these implementations is called an
op_mode.
The current op_mode is called DVM which states for dual virtual MAC.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: parse_tlv functions set the fw_version string
struct iwl_fw contains a string that describe the fw. This string
is now set by the iwl_parse_*_firmware.
This string is later used to update the cfg80211 data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Jakub Kicinski [Wed, 22 Feb 2012 20:58:58 +0000 (21:58 +0100)]
rt2800pci: Fix 'Error - MCU request failed' during initialization
Bring MCU operations during device initialization to sync
with legacy driver.
This should fix following error:
phy0 -> rt2800pci_mcu_status: Error - MCU request failed,
no response from hardware
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Wed, 22 Feb 2012 20:58:57 +0000 (21:58 +0100)]
rt2800: Add documentation on MCU requests
Add documentation on MCU communication, some of known commands and
their arguments. Supplement command ids.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Danny Kukawka [Wed, 15 Feb 2012 17:55:16 +0000 (18:55 +0100)]
iwlwifi: iwl-agn.h included twice
drivers/net/wireless/iwlwifi/iwl-core.c included 'iwl-agn.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Feb 2012 20:40:46 +0000 (21:40 +0100)]
mac80211: fix sta_info_flush() return value
The comment for sta_info_flush() states
"Returns the number of removed STA entries"
but that isn't actually true. Consequently,
the warning when a station is still around
on interface removal can never trigger and
this delayed finding the timer issue the
previous patch fixed. Fix the return value
here to make that warning useful again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Feb 2012 20:48:08 +0000 (21:48 +0100)]
mac80211: fix auth/assoc data & timer leak
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.
Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 24 Feb 2012 06:22:51 +0000 (07:22 +0100)]
brcm80211: fmac: use correct firmware filename
Also don't use so generic BRCMF_USB_FW_NAME as we may need different
firmwares in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 24 Feb 2012 06:22:27 +0000 (09:22 +0300)]
brcm80211: fmac: fix a couple checking after dereference bugs
There were two dereferencing before checking for NULL static checker
complaints in this new file. The list cursor is never NULL so that
check can be removed. I moved the other dereference after the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Thu, 23 Feb 2012 01:17:48 +0000 (02:17 +0100)]
mac80211: use proper sub_if_data on suspend path
Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log