Roland Dreier [Mon, 5 Mar 2012 18:05:28 +0000 (10:05 -0800)]
mlx4_core: Scale size of MTT table with system RAM
The current driver defaults to 1M MTT segments, where each segment holds
8 MTT entries. This limits the total memory registered to 8M * PAGE_SIZE
which is 32GB with 4K pages. Since systems that have much more memory
are pretty common now (at least among systems with InfiniBand hardware),
this limit ends up getting hit in practice quite a bit.
Handle this by having the driver allocate at least enough MTT entries to
cover 2 * totalram pages.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Wed, 11 Jan 2012 17:02:17 +0000 (19:02 +0200)]
mlx4_core: Allow dynamic MTU configuration for IB ports
Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB). Allow for dynamic mtu
configuration through a new, per-port sysfs entry.
Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.
For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode. To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Wed, 11 Jan 2012 17:00:29 +0000 (19:00 +0200)]
IB/mlx4: Fix info returned when querying IBoE ports
To issue a port query, use the QUERY_(Ethernet)_PORT command instead
of the MAD_IFC command, since MAD_IFC attempts to query the firmware
IB SMA, which is irrelevant for IBoE ports.
This allows us to handle both 10Gb/s and 40Gb/s rates (e.g in sysfs),
using QDR speed (10Gb/s) and width of 1X or 4X.
Signed-off-by: Dotan Barak <dotanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Eli Cohen [Tue, 6 Mar 2012 13:50:51 +0000 (15:50 +0200)]
IB/mlx4: Fix possible missed completion event
If an erroneous CQE is polled in the first iteration (i.e. npolled ==
0), we don't update the consumer index and hence the hardware could
get a wrong notion of how many CQEs software polled. Fix this by
unconditionally updating the doorbell record. We could change the
check to be something like
if (npolled || err != -EAGAIN)
...
but it does not seem worth the effort since a posted write to memory
should not cost too much.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Roland Dreier [Sun, 26 Feb 2012 09:48:12 +0000 (01:48 -0800)]
mlx4_core: Fix one more static exported function
Commit 22c8bff6face ("mlx4_core: Exported functions can't be static")
fixed most of this up, but forgot about mlx4_is_slave_active(). Fix
this one too.
Cc: <stable@vger.kernel.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Wed, 11 Jan 2012 17:03:51 +0000 (19:03 +0200)]
IB: Change CQE "csum_ok" field to a bit flag
Use a bit in wc_flags rather then a whole integer to hold the
"checksum OK" flag. By itself, this change doesn't reduce the size of
struct ib_wc on 64bit machines -- it stays on 56 bytes because of
padding. However, it will allow to add more fields in the future
without enlarging the struct. Also, it will let us have a unified
approach with future libibverbs checksum offload reporting, because a
bit flag doesn't break the library ABI.
This patch was suggested during conversation with Liran Liss
<liranl@mellanox.com>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Steve Wise [Wed, 7 Mar 2012 22:48:11 +0000 (16:48 -0600)]
RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
When destroying a listening cmid, the iwcm first marks the state of
the cmid as DESTROYING, then releases the lock and calls into the
iWARP provider to destroy the endpoint. Since the cmid is not locked,
its possible for the iWARP provider to pass a connection request event
to the iwcm, which will be silently dropped by the iwcm. This causes
the iWARP provider to never free up the resources from this connection
because the assumption is the iwcm will accept or reject this connection.
The solution is to reject these connection requests.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Tue, 6 Mar 2012 13:50:50 +0000 (15:50 +0200)]
mlx4_core: Get rid of redundant ext_port_cap flags
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).
This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Hefty, Sean [Fri, 2 Mar 2012 00:01:19 +0000 (00:01 +0000)]
RDMA/ucma: Fix AB-BA deadlock
When we destroy a cm_id, we must purge associated events from the
event queue. If the cm_id is for a listen request, we also purge
corresponding pending connect requests. This requires destroying
the cm_id's associated with the connect requests by calling
rdma_destroy_id(). rdma_destroy_id() blocks until all outstanding
callbacks have completed.
The issue is that we hold file->mut while purging events from the
event queue. We also acquire file->mut in our event handler. Calling
rdma_destroy_id() while holding file->mut can lead to a deadlock,
since the event handler callback cannot acquire file->mut, which
prevents rdma_destroy_id() from completing.
Fix this by moving events to purge from the event queue to a temporary
list. We can then release file->mut and call rdma_destroy_id()
outside of holding any locks.
Bug report by Or Gerlitz <ogerlitz@mellanox.com>:
[ INFO: possible circular locking dependency detected ] 3.3.0-rc5-00008-g79f1e43-dirty #34 Tainted: G I
tgtd/9018 is trying to acquire lock:
(&id_priv->handler_mutex){+.+.+.}, at: [<ffffffffa0359a41>] rdma_destroy_id+0x33/0x1f0 [rdma_cm]
but task is already holding lock:
(&file->mut){+.+.+.}, at: [<ffffffffa02470fe>] ucma_free_ctx+0xb6/0x196 [rdma_ucm]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Or Gerlitz [Tue, 28 Feb 2012 16:49:50 +0000 (18:49 +0200)]
IB: Use central enum for speed instead of hard-coded values
The kernel IB stack uses one enumeration for IB speed, which wasn't
explicitly specified in the verbs header file. Add that enum, and use
it all over the code.
The IB speed/width notation is also used by iWARP and IBoE HW drivers,
which use the convention of rate = speed * width to advertise their
port link rate.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Or Gerlitz [Mon, 5 Mar 2012 16:21:44 +0000 (18:21 +0200)]
IB/iser: Post initial receive buffers before sending the final login request
An iser target may send iscsi NO-OP PDUs as soon as it marks the iSER
iSCSI session as fully operative. This means that there is window
where there are no posted receive buffers on the initiator side, so
it's possible for the iSER RC connection to break because of RNR NAK /
retry errors. To fix this, rely on the flags bits in the login
request to have FFP (0x3) in the lower nibble as a marker for the
final login request, and post an initial chunk of receive buffers
before sending that login request instead of after getting the login
response.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Cc: <stable@vger.kernel.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
Doug Ledford [Thu, 1 Mar 2012 17:55:21 +0000 (19:55 +0200)]
IB/iser: Free IB connection resources in the proper place
We allocate the login dma buffers in iser_verbs.c as part of
alloc_ib_conn_resources(), however we are freeing them in
iser_initiator.c as part of iser_free_rx_descriptors(). This is
needlessly confusing. We have an alloc_rx_descriptors() and it
doesn't alloc something that the free_rx_descriptors() frees, and we
have an alloc_ib_conn_resources() that allocs something not freed by
free_ib_conn_resources(). Clean that up.
Signed-off-by: Doug Ledford <dledford@redhat.com>
[ Fix build error in iser_free_ib_conn_res(). - Or ]
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Bart Van Assche [Sat, 14 Jan 2012 12:40:44 +0000 (12:40 +0000)]
IB/srp: Consolidate repetitive sysfs code
Remove sysfs attributes before removing a target instead of testing
the target state in every sysfs attribute callback method. Note: it is
safe to invoke a sysfs attribute removal method like
device_remove_file() twice on the same attribute.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Roland Dreier <roland@purestorage.com>
Roland Dreier [Mon, 27 Feb 2012 17:15:08 +0000 (09:15 -0800)]
IB/core: Fix SDR rates in sysfs
Commit 71eeba16 ("IB: Add new InfiniBand link speeds") introduced a bug
where eg the rate for IB 4X SDR links iss displayed as "8.5 Gb/sec"
instead of "10 Gb/sec" as it used to be. Fix that.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Eli Cohen [Thu, 9 Feb 2012 16:10:06 +0000 (18:10 +0200)]
mlx4: Enforce device max FMR maps in FMR alloc
ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt. The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.
Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Mike Marciniszyn [Sun, 26 Feb 2012 01:45:50 +0000 (17:45 -0800)]
IB/qib: Avoid filtering LID on SMA portinfo
The current get portinfo handling filters the LID being sent,
changing zero to 0xffff.
This causes OpenSM to log excessive warning messages.
Reviewed-by: Edward Mascarenhas <edward.mascarenhas@qlogic.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Mike Marciniszyn [Sun, 26 Feb 2012 01:45:49 +0000 (17:45 -0800)]
IB/qib: Add logic for affinity hint
Call irq_set_affinity_hint() to give userspace programs such as
irqbalance the information to be able to distribute qib interrupts
appropriately.
The logic allocates all non-receive interrupts to the first CPU local
to the HCA. Receive interrupts are allocated round robin starting
with the second CPU local to the HCA with potential wrap back to the
second CPU.
This patch also adds a refinement to the name registered for MSI-X
interrupts so that user level scripts can determine the device
associated with the IRQs when there are multiple HCAs with a
potentially different set of local CPUs.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Linus Torvalds [Sat, 25 Feb 2012 20:12:08 +0000 (12:12 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Couple of minor driver fixes.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max34440) Fix resetting temperature history
hwmon: (f75375s) Fix register write order when setting fans to full speed
hwmon: (ads1015) Fix file leak in probe function
hwmon: (max6639) Fix PPR register initialization to set both channels
hwmon: (max6639) Fix FAN_FROM_REG calculation
Linus Torvalds [Sat, 25 Feb 2012 20:11:25 +0000 (12:11 -0800)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
three kbuild fixes for 3.3:
- make deb-pkg symlink race fix.
- make coccicheck fix.
- Dropping the check for modutils. This is not a regression, but
allows the module-init-tools replacement kmod work with the 3.3
kernel.
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
coccicheck: change handling of C={1,2} when M= is set
builddeb: Don't create files in /tmp with predictable names
kbuild: do not check for ancient modutils tools
Ian Kent [Wed, 22 Feb 2012 12:45:44 +0000 (20:45 +0800)]
autofs: work around unhappy compat problem on x86-64
When the autofs protocol version 5 packet type was added in commit 5c0a32fc2cd0 ("autofs4: add new packet type for v5 communications"), it
obvously tried quite hard to be word-size agnostic, and uses explicitly
sized fields that are all correctly aligned.
However, with the final "char name[NAME_MAX+1]" array at the end, the
actual size of the structure ends up being not very well defined:
because the struct isn't marked 'packed', doing a "sizeof()" on it will
align the size of the struct up to the biggest alignment of the members
it has.
And despite all the members being the same, the alignment of them is
different: a "__u64" has 4-byte alignment on x86-32, but native 8-byte
alignment on x86-64. And while 'NAME_MAX+1' ends up being a nice round
number (256), the name[] array starts out a 4-byte aligned.
End result: the "packed" size of the structure is 300 bytes: 4-byte, but
not 8-byte aligned.
As a result, despite all the fields being in the same place on all
architectures, sizeof() will round up that size to 304 bytes on
architectures that have 8-byte alignment for u64.
Note that this is *not* a problem for 32-bit compat mode on POWER, since
there __u64 is 8-byte aligned even in 32-bit mode. But on x86, 32-bit
and 64-bit alignment is different for 64-bit entities, and as a result
the structure that has exactly the same layout has different sizes.
So on x86-64, but no other architecture, we will just subtract 4 from
the size of the structure when running in a compat task. That way we
will write the properly sized packet that user mode expects.
Not pretty. Sadly, this very subtle, and unnecessary, size difference
has been encoded in user space that wants to read packets of *exactly*
the right size, and will refuse to touch anything else.
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 25 Feb 2012 00:08:51 +0000 (16:08 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes on 20120224:
"This is a set of assorted bug fixes for power management, mpt2sas,
ipr, the rdac device handler and quite a big chunk for qla2xxx (plus a
use after free of scsi_host in scsi_scan.c). "
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_dh_rdac: Fix for unbalanced reference count
[SCSI] scsi_pm: Fix bug in the SCSI power management handler
[SCSI] scsi_scan: Fix 'Poison overwritten' warning caused by using freed 'shost'
[SCSI] qla2xxx: Update version number to 8.03.07.13-k.
[SCSI] qla2xxx: Proper detection of firmware abort error code for ISP82xx.
[SCSI] qla2xxx: Remove resetting memory during device initialization for ISP82xx.
[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.
[SCSI] qla2xxx: Remove check for null fcport from host reset handler.
[SCSI] qla2xxx: Correct out of bounds read of ISP2200 mailbox registers.
[SCSI] qla2xxx: Remove errant clearing of MBX_INTERRUPT flag during CT-IOCB processing.
[SCSI] qla2xxx: Clear options-flags while issuing stop-firmware mbx command.
[SCSI] qla2xxx: Add an "is reset active" helper.
[SCSI] qla2xxx: Add check for null fcport references in qla2xxx_queuecommand.
[SCSI] qla2xxx: Propagate up abort failures.
[SCSI] isci: Fix NULL ptr dereference when no firmware is being loaded
[SCSI] ipr: fix eeh recovery for 64-bit adapters
[SCSI] mpt2sas: Fix mismatch in mpt2sas_base_hard_reset_handler() mutex lock-unlock
Linus Torvalds [Fri, 24 Feb 2012 20:32:51 +0000 (12:32 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
Oleg Nesterov [Fri, 24 Feb 2012 19:07:29 +0000 (20:07 +0100)]
epoll: ep_unregister_pollwait() can use the freed pwq->whead
signalfd_cleanup() ensures that ->signalfd_wqh is not used, but
this is not enough. eppoll_entry->whead still points to the memory
we are going to free, ep_unregister_pollwait()->remove_wait_queue()
is obviously unsafe.
Change ep_poll_callback(POLLFREE) to set eppoll_entry->whead = NULL,
change ep_unregister_pollwait() to check pwq->whead != NULL under
rcu_read_lock() before remove_wait_queue(). We add the new helper,
ep_remove_wait_queue(), for this.
This works because sighand_cachep is SLAB_DESTROY_BY_RCU and because
->signalfd_wqh is initialized in sighand_ctor(), not in copy_sighand.
ep_unregister_pollwait()->remove_wait_queue() can play with already
freed and potentially reused ->sighand, but this is fine. This memory
must have the valid ->signalfd_wqh until rcu_read_unlock().
Oleg Nesterov [Fri, 24 Feb 2012 19:07:11 +0000 (20:07 +0100)]
epoll: introduce POLLFREE to flush ->signalfd_wqh before kfree()
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
Linus Torvalds [Fri, 24 Feb 2012 17:02:53 +0000 (09:02 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Quoth Chris:
"This is later than I wanted because I got backed up running through
btrfs bugs from the Oracle QA teams. But they are all bug fixes that
we've queued and tested since rc1.
Nothing in particular stands out, this just reflects bug fixing and QA
done in parallel by all the btrfs developers. The most user visible
of these is:
Btrfs: clear the extent uptodate bits during parent transid failures
Because that helps deal with out of date drives (say an iscsi disk
that has gone away and come back). The old code wasn't always
properly retrying the other mirror for this type of failure."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (24 commits)
Btrfs: fix compiler warnings on 32 bit systems
Btrfs: increase the global block reserve estimates
Btrfs: clear the extent uptodate bits during parent transid failures
Btrfs: add extra sanity checks on the path names in btrfs_mksubvol
Btrfs: make sure we update latest_bdev
Btrfs: improve error handling for btrfs_insert_dir_item callers
Btrfs: be less strict on finding next node in clear_extent_bit
Btrfs: fix a bug on overcommit stuff
Btrfs: kick out redundant stuff in convert_extent_bit
Btrfs: skip states when they does not contain bits to clear
Btrfs: check return value of lookup_extent_mapping() correctly
Btrfs: fix deadlock on page lock when doing auto-defragment
Btrfs: fix return value check of extent_io_ops
btrfs: honor umask when creating subvol root
btrfs: silence warning in raid array setup
btrfs: fix structs where bitfields and spinlock/atomic share 8B word
btrfs: delalloc for page dirtied out-of-band in fixup worker
Btrfs: fix memory leak in load_free_space_cache()
btrfs: don't check DUP chunks twice
Btrfs: fix trim 0 bytes after a device delete
...
Linus Torvalds [Fri, 24 Feb 2012 17:01:46 +0000 (09:01 -0800)]
Merge tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming
This is the arch/c6x part of commit 7c43185138cf ("Kbuild: Use dtc's -d
(dependency) option") which was dropped because c6x had not yet been
merged at the time.
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
Kbuild: Use dtc's -d (dependency) option
Kyle McMartin [Fri, 24 Feb 2012 15:36:16 +0000 (10:36 -0500)]
MAINTAINERS: drop me from PA-RISC maintenance
I don't even live in the same country as any of my PA-RISC hardware
these days, so the odds of me touching the code are pretty low.
(Also re-order things to ensure jejb gets CC'd since he's been the
primary maintainer for the last few years.)
David Howells [Thu, 23 Feb 2012 13:50:35 +0000 (13:50 +0000)]
NOMMU: Lock i_mmap_mutex for access to the VMA prio list
Lock i_mmap_mutex for access to the VMA prio list to prevent concurrent
access. Currently, certain parts of the mmap handling are protected by
the region mutex, but not all.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk>
cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 24 Feb 2012 16:56:51 +0000 (08:56 -0800)]
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
SuperH fixes for 3.3-rc5
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix sh2a build error for CONFIG_CACHE_WRITETHROUGH
sh: modify a resource of sh_eth_giga1_resources in board-sh7757lcr
arch/sh: remove references to cpu_*_map.
sh: Fix typo in pci-sh7780.c
sh: add platform_device for SPI1 in setup-sh7757
sh: modify resource for SPI0 in setup-sh7757
sh: se7724: fix compile breakage
sh: clkfwk: bugfix: use clk_reparent() for div6 clocks
sh: clock-sh7724: fixup sh_fsi clock settings
sh: sh7757lcr: update to the new MMCIF DMA configuration
sh: fix the sh_mmcif_plat_data in board-sh7757lcr
video: pvr2fb: Fix up spurious section mismatch warnings.
sh: Defer to asm-generic/device.h.
Anton Vorontsov [Fri, 24 Feb 2012 01:14:46 +0000 (05:14 +0400)]
mm: memcg: Correct unregistring of events attached to the same eventfd
There is an issue when memcg unregisters events that were attached to
the same eventfd:
- On the first call mem_cgroup_usage_unregister_event() removes all
events attached to a given eventfd, and if there were no events left,
thresholds->primary would become NULL;
- Since there were several events registered, cgroups core will call
mem_cgroup_usage_unregister_event() again, but now kernel will oops,
as the function doesn't expect that threshold->primary may be NULL.
That's a good question whether mem_cgroup_usage_unregister_event()
should actually remove all events in one go, but nowadays it can't
do any better as cftype->unregister_event callback doesn't pass
any private event-associated cookie. So, let's fix the issue by
simply checking for threshold->primary.
FWIW, w/o the patch the following oops may be observed:
Rusty Russell [Wed, 15 Feb 2012 04:58:04 +0000 (15:28 +1030)]
arch/sh: remove references to cpu_*_map.
This has been obsolescent for a while; time for the final push.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Paul Mundt <lethal@linux-sh.org> Cc: linux-sh@vger.kernel.org Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With kernel 3.1, Christoph removed i_alloc_sem and replaced it with
calls (namely inode_dio_wait() and inode_dio_done()) which are
EXPORT_SYMBOL_GPL() thus they cannot be used by non-GPL file systems and
further inode_dio_wait() was pushed from notify_change() into the file
system ->setattr() method but no non-GPL file system can make this call.
That means non-GPL file systems cannot exist any more unless they do not
use any VFS functionality related to reading/writing as far as I can
tell or at least as long as they want to implement direct i/o.
Both Linus and Al (and others) have said on LKML that this breakage of
the VFS API should not have happened and that the change was simply
missed as it was not documented in the change logs of the patches that
did those changes.
This patch changes the two function exports in question to be
EXPORT_SYMBOL() thus restoring the VFS API as it used to be - accessible
for all modules.
Christoph, who introduced the two functions and exported them GPL-only
is CC-ed on this patch to give him the opportunity to object to the
symbols being changed in this manner if he did indeed intend them to be
GPL-only and does not want them to become available to all modules.
Signed-off-by: Anton Altaparmakov <anton@tuxera.com> CC: Christoph Hellwig <hch@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 23 Feb 2012 23:38:57 +0000 (15:38 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
A fix from Jesper Juhl removes an assignment in an ASSERT when a compare
is intended. Two fixes from Mitsuo Hayasaka address off-by-ones in XFS
quota enforcement.
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: make inode quota check more general
xfs: change available ranges of softlimit and hardlimit in quota check
XFS: xfs_trans_add_item() - don't assign in ASSERT() when compare is intended
Linus Torvalds [Thu, 23 Feb 2012 19:48:36 +0000 (11:48 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
BenH says:
'Here are a few more powerpc bits for you. A stupid regression I
introduced with my previous commit to "fix" program check exceptions
(brown paper bag for me), fix the cpuidle default, a bug fix for
something that isn't strictly speaking a regression but some upstream
changes causes it to show in lockdep now while it didn't before, and
finally a trivial one for rusty to make his life easier later on
removing the old cpumask cruft. '
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix various issues with return to userspace
cpuidle: Default y on powerpc pSeries
powerpc: Fix program check handling when lockdep is enabled
powerpc: Remove references to cpu_*_map
Chris Mason [Wed, 22 Feb 2012 17:36:24 +0000 (12:36 -0500)]
Btrfs: clear the extent uptodate bits during parent transid failures
If btrfs reads a block and finds a parent transid mismatch, it clears
the uptodate flags on the extent buffer, and the pages inside it. But
we only clear the uptodate bits in the state tree if the block straddles
more than one page.
This is from an old optimization from to reduce contention on the extent
state tree. But it is buggy because the code that retries a read from
a different copy of the block is going to find the uptodate state bits
set and skip the IO.
The end result of the bug is that we'll never actually read the good
copy (if there is one).
The fix here is to always clear the uptodate state bits, which is safe
because this code is only called when the parent transid fails.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Nikolaus Schulz [Wed, 22 Feb 2012 22:18:44 +0000 (23:18 +0100)]
hwmon: (f75375s) Fix register write order when setting fans to full speed
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Guenter Roeck [Wed, 22 Feb 2012 16:13:52 +0000 (08:13 -0800)]
hwmon: (ads1015) Fix file leak in probe function
An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Doug Ledford [Mon, 20 Feb 2012 17:19:03 +0000 (12:19 -0500)]
mlx4_core: Exported functions can't be static
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Linus Torvalds [Wed, 22 Feb 2012 19:58:30 +0000 (11:58 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Intel, radeon, exynos fixes.
Intel: fixes a few Ivybridge hangs, along with fixing RC6 on SNB (still
not on, but at least allows for distros to patch it on easily).
radeon: oops reading some files in debugfs that weren't meant to appear,
a fix that touches a lot of files, so looks worse than it is, it fixes
an oops if a GPU reset fails and userspace keeps submitting more data,
along with a minor BIOS fix for newer boards.
exynos: a group of fixes for exynos, they've sent me a few more but
these were all I got through, and its no hw vanilla kernel users see a
lot off yet.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: dpms bios scratch reg updates
drm/radeon/kms: properly set accel working flag and bailout when false
drm/radeon: Only create additional ring debugfs files on Cayman or newer.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
Moger, Babu [Thu, 2 Feb 2012 15:21:54 +0000 (15:21 +0000)]
[SCSI] scsi_dh_rdac: Fix for unbalanced reference count
This patch fixes an unbalanced refcount issue.
Elevating the lock for both kref_put and also for controller node deletion.
Previously, controller deletion was protected but the not the kref_put. This
was causing the other thread to pick up the controller structure which was
already kref'd zero.
This was causing the following WARN_ON and also sometimes panic.
Linus Torvalds [Wed, 22 Feb 2012 16:45:08 +0000 (08:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
It contains 3 important fixes for ColdFire based machines:
- fix processes getting stuck when running from strace
- fix kernel vmalloced pages not being visible in all kernel contexts
- fix shared user pages sometimes being visible in another process
context
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: Do not set global share for non-kernel shared pages
m68k: Add shared bit to Coldfire kernel page entries
m68knommu: fix syscall tracing stuck process
Linus Torvalds [Wed, 22 Feb 2012 16:43:35 +0000 (08:43 -0800)]
Merge tag 'nfs-for-3.3-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Bugfixes for the NFS client.
Fix a nasty Oops in the NFSv4 getacl code, another source of infinite
loops in the NFSv4 state recovery code, and a regression in NFSv4.1
session initialisation.
Also deal with an NFSv4.1 memory leak.
* tag 'nfs-for-3.3-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: fix server_scope memory leak
NFSv4.1: Fix a NFSv4.1 session initialisation regression
NFSv4: Ensure we throw out bad delegation stateids on NFS4ERR_BAD_STATEID
NFSv4: Fix an Oops in the NFSv4 getacl code
Jerome Glisse [Mon, 20 Feb 2012 22:57:20 +0000 (17:57 -0500)]
drm/radeon/kms: properly set accel working flag and bailout when false
If accel is not working many subsystem such as the ib pool might not be
initialized properly that can lead to segfault inside kernel when cs
ioctl is call with non working acceleration. To avoid this make sure
the accel working flag is false when an error in GPU startup happen and
return EBUSY from cs ioctl if accel is not working.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested with a Cayman card in a Llano system: The additional files are created
and working for the Cayman card but not created for the CPU's built-in GPU.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 22 Feb 2012 08:02:17 +0000 (08:02 +0000)]
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
powerpc: Fix various issues with return to userspace
We have a few problems when returning to userspace. This is a
quick set of fixes for 3.3, I'll look into a more comprehensive
rework for 3.4. This fixes:
- We kept interrupts soft-disabled when schedule'ing or calling
do_signal when returning to userspace as a result of a hardware
interrupt.
- Rename do_signal to do_notify_resume like all other archs (and
do_signal_pending back to do_signal, which it was before Roland
changed it).
- Add the missing call to key_replace_session_keyring() to
do_notify_resume().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Michael Ellerman [Mon, 20 Feb 2012 21:32:30 +0000 (21:32 +0000)]
powerpc: Fix program check handling when lockdep is enabled
In commit 54321242afe ("Disable interrupts early in Program Check"), we
switched from enabling to disabling interrupts in program_check_common.
Whereas ENABLE_INTS leaves r3 untouched, if lockdep is enabled DISABLE_INTS
calls into lockdep code and will clobber r3. That means we pass a bogus
struct pt_regs* into program_check_exception() and all hell breaks loose.
So load our regs pointer into r3 after we call DISABLE_INTS.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Wed, 22 Feb 2012 02:24:42 +0000 (18:24 -0800)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
A few more things this time around. The only thing warranting some
commentry is the modpost change, which allows folk building a Thumb2
enabled kernel to see section mismatch warnings. This is why many
weren't noticed with OMAP.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM/audit: include audit header and fix audit arch
ARM: OMAP: fix voltage domain build errors with PM_OPP disabled
ARM/PCI: Remove ARM's duplicate definition of 'pcibios_max_latency'
ARM: 7336/1: smp_twd: Don't register CPUFREQ notifiers if local timers are not initialised
ARM: 7327/1: need to include asm/system.h in asm/processor.h
ARM: 7326/2: PL330: fix null pointer dereference in pl330_chan_ctrl()
ARM: 7164/3: PL330: Fix the size of the dst_cache_ctrl field
ARM: 7325/1: fix v7 boot with lockdep enabled
ARM: 7324/1: modpost: Fix section warnings for ARM for many compilers
ARM: 7323/1: Do not allow ARM_LPAE on pre-ARMv7 architectures
Linus Torvalds [Wed, 22 Feb 2012 01:24:20 +0000 (17:24 -0800)]
sys_poll: fix incorrect type for 'timeout' parameter
The 'poll()' system call timeout parameter is supposed to be 'int', not
'long'.
Now, the reason this matters is that right now 32-bit compat mode is
broken on at least x86-64, because the 32-bit code just calls
'sys_poll()' directly on x86-64, and the 32-bit argument will have been
zero-extended, turning a signed 'int' into a large unsigned 'long'
value.
We could just introduce a 'compat_sys_poll()' function for this, and
that may eventually be what we have to do, but since the actual standard
poll() semantics is *supposed* to be 'int', and since at least on x86-64
glibc sign-extends the argument before invocing the system call (so
nobody can actually use a 64-bit timeout value in user space _anyway_,
even in 64-bit binaries), the simpler solution would seem to be to just
fix the definition of the system call to match what it should have been
from the very start.
If it turns out that somebody somehow circumvents the user-level libc
64-bit sign extension and actually uses a large unsigned 64-bit timeout
despite that not being how poll() is supposed to work, we will need to
do the compat_sys_poll() approach.
Reported-by: Thomas Meyer <thomas@m3y3r.de> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hitoshi Mitake [Tue, 7 Feb 2012 02:45:33 +0000 (11:45 +0900)]
asm-generic: architecture independent readq/writeq for 32bit environment
This provides unified readq()/writeq() helper functions for 32-bit
drivers.
For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.
- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address
- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order
This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0affd5 ("x86:
remove 32-bit versions of readq()/writeq()")
The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:
#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */
But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access
This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.
Cc: Kashyap Desai <Kashyap.Desai@lsi.com> Cc: Len Brown <lenb@kernel.org> Cc: Ravi Anand <ravi.anand@qlogic.com> Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Jason Uhlenkott <juhlenko@akamai.com> Cc: James Bottomley <James.Bottomley@parallels.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Roland Dreier <roland@purestorage.com> Cc: James Bottomley <jbottomley@parallels.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Matthew Wilcox <matthew.r.wilcox@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Stern [Tue, 21 Feb 2012 18:16:32 +0000 (13:16 -0500)]
usb-storage: fix freezing of the scanning thread
This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
Merge tag 'for-usb-linus-2012-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Hi Greg,
Here's three bug fixes that should be queued for 3.3.
The first fixes an issue we saw with an Intel Panther Point xHCI host,
where a certain OSV's custom BIOS would disable the PCI device during
boot. It changes the generic PCI quirks handler for all USB host
controllers, but in a way both Jesse Barnes and Oliver Neukum have
agreed is safe.
The second patch is Elric Fu's first kernel patch! Congrats! It fixes
a bug in the USB 3.0 hub reset handling.
The last patch fixes a bug in the xHCI driver that feeds invalid input
to the xHC host. Only the VIA host controller seems to have issues with
it. Thanks to Felipe Contreras for testing this patch on his VIA host,
and Andiry Xu for suggesting the fix.
Sarah Sharp [Mon, 13 Feb 2012 22:42:11 +0000 (14:42 -0800)]
xhci: Fix encoding for HS bulk/control NAK rate.
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Felipe Contreras <felipe.contreras@gmail.com> Suggested-by: Andiry Xu <andiry.xu@amd.com> Cc: stable@vger.kernel.org
Elric Fu [Sat, 18 Feb 2012 05:32:27 +0000 (13:32 +0800)]
USB: Set hub depth after USB3 hub reset
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org
Sarah Sharp [Tue, 7 Feb 2012 23:11:46 +0000 (15:11 -0800)]
USB: Fix handoff when BIOS disables host PCI device.
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Oliver Neukum <oneukum@suse.de> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: stable@vger.kernel.org
Chris D Schimp [Mon, 20 Feb 2012 22:44:59 +0000 (17:44 -0500)]
hwmon: (max6639) Fix PPR register initialization to set both channels
Initialize PPR register for both channels, and set correct PPR register bits.
Also remove unnecessary variable initializations.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: Merged two patches into one] Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: stable@vger.kernel.org # 3.0+ Acked-by: Roland Stigge <stigge@antcom.de>
Chris D Schimp [Mon, 20 Feb 2012 21:59:24 +0000 (16:59 -0500)]
hwmon: (max6639) Fix FAN_FROM_REG calculation
RPM calculation from tachometer value does not depend on PPR.
Also, do not report negative RPM values.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: do not report negative RPM values] Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: stable@vger.kernel.org # 3.0+ Acked-by: Roland Stigge <stigge@antcom.de>
CC arch/arm/kernel/ptrace.o
arch/arm/kernel/ptrace.c: In function 'syscall_trace':
arch/arm/kernel/ptrace.c:919: error: implicit declaration of function 'audit_syscall_exit'
arch/arm/kernel/ptrace.c:921: error: implicit declaration of function 'audit_syscall_entry'
arch/arm/kernel/ptrace.c:921: error: 'AUDIT_ARCH_ARMEB' undeclared (first use in this function)
arch/arm/kernel/ptrace.c:921: error: (Each undeclared identifier is reported only once
arch/arm/kernel/ptrace.c:921: error: for each function it appears in.)
make[1]: *** [arch/arm/kernel/ptrace.o] Error 1
make: *** [arch/arm/kernel] Error 2
This part of the patch is: Reported-by: Axel Lin <axel.lin@gmail.com> Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
(They both provided patches to fix it)
This patch also (at the request of the list) fixes the fact that
ARM has both LE and BE versions however the audit code was called as if
it was always BE. If audit userspace were to try to interpret the bits
it got from a LE system it would obviously do so incorrectly. Fix this
by using the right arch flag on the right system.
This part of the patch is: Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-beck.git / log