Daniel Drake [Mon, 21 Nov 2011 15:05:56 +0000 (15:05 +0000)]
viafb: correct sync polarity for OLPC DCON
While the OLPC display appears to be able to handle either positive
or negative sync, the Display Controller only recognises positive sync.
This brings viafb (for XO-1.5) in line with lxfb (for XO-1) and
fixes a recent regression where the XO-1.5 DCON could no longer be
frozen. Thanks to Florian Tobias Schandinat for helping identify
the fix.
Test case: from a vt,
echo 1 > /sys/devices/platform/dcon/freeze
should cause the current screen contents to freeze, rather than garbage being
displayed.
video:da8xx-fb: Disable and reset sequence on version2 of LCDC
Patch follows the disable and software reset sequence specified
in version2 to LCDC functional specification.
Without this flicker is observed on re-enabling the LCDC.
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
VMLEN1/VMLEN2 needs blanking length which is calculated from
video image size.
The calculation methods are explained on
[SH MIPI] - [Video Mode] - [Blanking Packet setting]
But HFPLEN (= VMLEN2) is un-understandable.
For example, if SH-MIPI input was RGB888 (3byte),
output was RGB888 (3byte)
and 3lane connection, the date goes straight.
But if SH-MIPI input was RGB888 (3byte),
output was RGB565 (2byte)
and 4lane connection, it needs delay in HFPLEN.
Then (input cycle - output cycle) * lane is necessary the delay
Tomi Valkeinen [Tue, 1 Nov 2011 08:50:45 +0000 (10:50 +0200)]
OMAPDSS: DISPC: skip scaling calculations when not scaling
Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.
This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:
omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz
A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Tue, 8 Nov 2011 07:54:50 +0000 (09:54 +0200)]
OMAPFB: fix compilation warnings due to missing include
Fix warnings similar to this by including module.h:
drivers/video/omap/dispc.c:276:1: warning: data definition has no type
or storage class
drivers/video/omap/dispc.c:276:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL'
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 20 Oct 2011 10:36:59 +0000 (13:36 +0300)]
OMAPDSS: HDMI: fix returned HDMI pixel clock
hdmi_get_pixel_clock() returns the pixel clock in Hz, but the pck is
stored as kHz. This means the return value has to be multiplied by 1000,
not by 10000 as the code did.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Linus Torvalds [Tue, 15 Nov 2011 16:48:51 +0000 (14:48 -0200)]
Merge branch 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl
* 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl:
pinctrl: hide subsystem from the populace
pinctrl: fix "warning: 'struct pinctrl_dev' declared inside parameter list"
Linus Torvalds [Tue, 15 Nov 2011 16:45:50 +0000 (14:45 -0200)]
Merge branch 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: pca953x: propagate the errno from the chip_init functions
gpio: pca953x: remove unneeded check for chip type
gpio/omap: check return value from irq_alloc_generic_chip
gpio/omap: replace MOD_REG_BIT macro with static inline
Linus Torvalds [Tue, 15 Nov 2011 16:31:12 +0000 (14:31 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
blackfin: Fixup export.h includes
Blackfin: add serial TX IRQ in individual platform resource
Liu Gang [Fri, 11 Nov 2011 13:48:28 +0000 (21:48 +0800)]
fsl-rio: fix compile error
The "#include <linux/module.h>" was replaced by "#include <linux/export.h>"
in the patch "powerpc: various straight conversions from module.h --> export.h".
This will cause the following compile problem:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:296: error: implicit declaration of function 'search_exception_tables'.
The file fsl_rio.c needs the declaration of function "search_exception_tables"
in the header file "linux/module.h".
Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 8dc7a9c84 ("blackfin: Add export.h to files using
EXPORT_SYMBOL/THIS_MODULE") inserted some of the include statements into
sections protected by an unrelated #if CONFIG_... statement. This can cause,
depending on the configuration used, warnings like this one:
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: data definition has no type or storage class
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: parameter names (without types) in function declaration
This patch fixes it by moving the includes out of the #if protected sections.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bob Liu <lliubbo@gmail.com>
Linus Torvalds [Mon, 14 Nov 2011 08:47:04 +0000 (06:47 -0200)]
Merge branch 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
Commit 31a3ddda166cda86d2b5111e09ba4bda5239fae6 introduced
a use after free in virtio-pci. The main issue is
that the release method signals removal of the virtio device,
while remove signals removal of the pci device.
For example, on driver removal or hot-unplug,
virtio_pci_release_dev is called before virtio_pci_remove.
We then might get a crash as virtio_pci_remove tries to use the
device freed by virtio_pci_release_dev.
We allocate/free all resources together with the
pci device, so we can leave the release method empty.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org
After commit e978aa7d7d57 ("cpuidle: Move dev->last_residency update to
driver enter routine; remove dev->last_state") setting acpi_idle_suspend
to 1 by acpi_processor_suspend() causes the ACPI cpuidle routines to
return error codes continuously, which in turn causes cpuidle to lock up
(hard).
However, acpi_idle_suspend doesn't appear to be useful for any
particular purpose (it's racy and doesn't really provide any real
protection), so it can be removed, which makes the problem go away.
Reported-and-tested-by: Tomas M. <tmezzadra@gmail.com> Reported-and-tested-by: Ferenc Wagner <wferi@niif.hu> Tested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 4 Nov 2011 12:04:41 +0000 (20:04 +0800)]
[CPUFREQ] db8500: fix build error due to undeclared i variable
The variable i is removed by commit ded8433
"[CPUFREQ] db8500: remove unneeded for loop iteration over freq_table",
but current code to print available frequencies still uses the i variable.
Thus add the i variable back to fix below buld error:
CC drivers/cpufreq/db8500-cpufreq.o
drivers/cpufreq/db8500-cpufreq.c: In function 'db8500_cpufreq_init':
drivers/cpufreq/db8500-cpufreq.c:123: error: 'i' undeclared (first use in this function)
drivers/cpufreq/db8500-cpufreq.c:123: error: (Each undeclared identifier is reported only once
drivers/cpufreq/db8500-cpufreq.c:123: error: for each function it appears in.)
make[2]: *** [drivers/cpufreq/db8500-cpufreq.o] Error 1
make[1]: *** [drivers/cpufreq] Error 2
make: *** [drivers] Error 2
This patch also fixes using uninitialized i variable as array index.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dave Jones <davej@redhat.com>
Linus Torvalds [Sat, 12 Nov 2011 02:04:51 +0000 (00:04 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (29 commits)
m68k/mac: Remove mac_irq_{en,dis}able() wrappers
m68k/irq: Remove obsolete support for user vector interrupt fixups
m68k/irq: Remove obsolete m68k irq framework
m68k/q40: Convert Q40/Q60 to genirq
m68k/sun3: Convert Sun3/3x to genirq
m68k/sun3: Use the kstat_irqs_cpu() wrapper
m68k/apollo: Convert Apollo to genirq
m68k/vme: Convert VME to genirq
m68k/hp300: Convert HP9000/300 and HP9000/400 to genirq
m68k/mac: Optimize interrupts using chain handlers
m68k/mac: Convert Mac to genirq
m68k/amiga: Optimize interrupts using chain handlers
m68k/amiga: Convert Amiga to genirq
m68k/amiga: Refactor amiints.c
m68k/atari: Remove code and comments about different irq types
m68k/atari: Convert Atari to genirq
m68k/irq: Add genirq support
m68k/irq: Remove obsolete IRQ_FLG_* users
m68k/irq: Rename {,__}m68k_handle_int()
m68k/irq: Add m68k_setup_irq_controller()
...
Linus Torvalds [Sat, 12 Nov 2011 02:03:50 +0000 (00:03 -0200)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l2-ctrl: Send change events to all fh for auto cluster slave controls
[media] v4l2-event: Don't set sev->fh to NULL on unsubscribe
[media] v4l2-event: Remove pending events from fh event queue when unsubscribing
[media] v4l2-event: Deny subscribing with a type of V4L2_EVENT_ALL
[media] MAINTAINERS: add a maintainer for s5p-mfc driver
[media] v4l: s5p-mfc: fix reported capabilities
[media] media: vb2: reset queued list on REQBUFS(0) call
[media] media: vb2: set buffer length correctly for all buffer types
[media] media: vb2: add a check for uninitialized buffer
[media] mxl111sf: fix build warning
[media] mxl111sf: remove pointless if condition in mxl111sf_config_spi
[media] mxl111sf: check for errors after mxl111sf_write_reg in mxl111sf_idac_config
[media] mxl111sf: fix return value of mxl111sf_idac_config
[media] uvcvideo: GET_RES should only be checked for BITMAP type menu controls
Linus Torvalds [Sat, 12 Nov 2011 02:01:51 +0000 (00:01 -0200)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/kvm: Fix build failure with HV KVM and CBE
powerpc/ps3: Fix lv1_gpu_attribute hcall
powerpc/ps3: Fix PS3 repository build warnings
powerpc/ps3: irq: Remove IRQF_DISABLED
powerpc/irq: Remove IRQF_DISABLED
powerpc/numa: NUMA topology support for PowerNV
powerpc: Add System RAM to /proc/iomem
powerpc: Add KVM as module to defconfigs
powerpc/kvm: Fix build with older toolchains
powerpc, tqm5200: update tqm5200_defconfig to fit for charon board.
powerpc/5200: add support for charon board
William Douglas [Thu, 10 Nov 2011 13:50:38 +0000 (13:50 +0000)]
bma023: Add SFI translation for this device
This needed the sfi IRQ 0xFF fix to go in first. It simply plumbs in the
bma023 driver with the firmware naming of it.
Signed-off-by: William Douglas <william.douglas@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Feng Tang [Thu, 10 Nov 2011 13:23:39 +0000 (13:23 +0000)]
vrtc: change its year offset from 1960 to 1972
Real world year equals the value in vrtc YEAR register plus an offset.
We used 1960 as the offset to make leap year consistent, but for a
device's first use, its YEAR register is 0 and the system year will
be parsed as 1960 which is not a valid UNIX time and will cause many
applications to fail mysteriously. So we use 1972 instead to fix this
issue.
Updated patch which adds a sanity check suggested by Mathias
This isn't a change in behaviour for systems, because 1972 is the one we
actually use. It's the old version in upstream which is out of sync with
all devices.
Linus Torvalds [Sat, 12 Nov 2011 01:47:06 +0000 (23:47 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: rename the option to nospace_cache
Btrfs: handle bio_add_page failure gracefully in scrub
Btrfs: fix deadlock caused by the race between relocation
Btrfs: only map pages if we know we need them when reading the space cache
Btrfs: fix orphan backref nodes
Btrfs: Abstract similar code for btrfs_block_rsv_add{, _noflush}
Btrfs: fix unreleased path in btrfs_orphan_cleanup()
Btrfs: fix no reserved space for writing out inode cache
Btrfs: fix nocow when deleting the item
Btrfs: tweak the delayed inode reservations again
Btrfs: rework error handling in btrfs_mount()
Btrfs: close devices on all error paths in open_ctree()
Btrfs: avoid null dereference and leaks when bailing from open_ctree()
Btrfs: fix subvol_name leak on error in btrfs_mount()
Btrfs: fix memory leak in btrfs_parse_early_options()
Btrfs: fix our reservations for updating an inode when completing io
Btrfs: fix oops on NULL trans handle in btrfs_truncate
btrfs: fix double-free 'tree_root' in 'btrfs_mount()'
Linus Torvalds [Sat, 12 Nov 2011 01:45:42 +0000 (23:45 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Use kmemdup rather than duplicating its implementation
ALSA: hda - Re-enable the check NO_PRESENCE misc bit
ALSA: vmaster - Free slave-links when freeing the master element
ALSA: hda - Don't add elements of other codecs to vmaster slave
ALSA: intel8x0: improve virtual environment detection
ALSA: intel8x0: move virtual environment detection code into one place
ALSA: snd_usb_audio: add Logitech HD Webcam c510 to quirk-384
ALSA: hda - fix internal mic on Dell Vostro 3500 laptop
ALSA: HDA: Remove quirk for Toshiba T110
ALSA: usb-audio - Fix the missing volume quirks at delayed init
ALSA: hda - Mute unused capture sources for Realtek codecs
ALSA: intel8x0: Improve comments for VM optimization
ASoC: Ensure we get an impedence reported for WM8958 jack detect
ASoC: Don't use wm8994->control_data when requesting IRQs
ASoC: Don't use wm8994->control_data in wm8994_readable_register()
ASoC: Update git repository URL
Linus Torvalds [Sat, 12 Nov 2011 01:43:51 +0000 (23:43 -0200)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/radeon/kms/pm: switch to dynamically allocating clock mode array
drm/radeon/kms: optimize r600_pm_profile_init
drm/radeon/kms/pm: add a proper pm profile init function for fusion
drm/radeon/kms: remove extraneous calls to radeon_pm_compute_clocks()
drm/exynos: added padding to be 64-bit align.
drm: fix kconfig unmet dependency warning
drm: add some comments to drm_wait_vblank and drm_queue_vblank_event
drm/radeon/benchmark: signedness bug in radeon_benchmark_move()
drm: do not sleep on vblank while holding a mutex
MAINTAINERS: exynos: Add EXYNOS DRM maintainer entry
drm: try to restore previous CRTC config if mode set fails
drm/radeon/kms: make an aux failure debug only
drm: drop select of SLOW_WORK
drm: serialize access to list of debugfs files
drm/radeon/kms: fix use of vram scratch page on evergreen/ni
drm/radeon: Make sure CS mutex is held across GPU reset.
drm: Ensure string is null terminated.
vmwgfx: Only allow 64x64 cursors
vmwgfx: Initialize clip rect loop correctly in surface dirty
vmwgfx: Close screen object system
...
Linus Torvalds [Sat, 12 Nov 2011 01:37:17 +0000 (23:37 -0200)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix force shutdown handling in xfs_end_io
xfs: constify xfs_item_ops
xfs: Fix possible memory corruption in xfs_readlink
fbdev/cirrusfb: Add support for Picasso IV in Zorro II mode
In Zorro II mode, the Village Tronic Picasso IV graphics card shows up as
either 2 or 3 Zorro devices:
- One for the registers of the Cirrus Logic graphics chip,
- One for the first bank of 2 MiB of graphics memory,
- An optional one for the second bank of 2 MiB of graphics memory,
if there was enough free Zorro II address space.
Based on src/sys/arch/amiga/dev/grf_cl.c from NetBSD.
As indicated by commit a7f4d00a82feb5b311f765bf9522bc55bee0684f ("zorro:
Defer device_register() until all devices have been identified"), cirrusfb
crashes if zorro_find_device() cannot find an expected device.
Rewrite the Zorro device probe code to make it more robust, easier to
understand, and more extensible.
Other logical changes:
- For cards that show up as 2 Zorro devices, autoprobe graphics memory
sizes based on the size of the Zorro device containing the graphics
memory.
Acording to the NetBSD sources, this is safe.
Alexander Stein [Wed, 5 Oct 2011 07:59:58 +0000 (09:59 +0200)]
atmel_lcdfb: Use proper blanking on negative contrast polarity
If used with negative polarity the PWM unit cannot be disabled. This would
result in a full contrast screen.
Instead let the PWM unit enabled using 0x0 as compare value which darkens
the display.
In result no power saving is possible if inverted contrast polarity
is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Alexander Stein [Wed, 5 Oct 2011 07:59:57 +0000 (09:59 +0200)]
atmel_lcdfb: Adjust HFP calculation so it matches the manual.
In the AT91SAM9263 Manual the HFP part in LCDTIM2 is described as follows:
* HFP: Horizontal Front Porch
Number of idle LCDDOTCK cycles at the end of the line.
Idle period is (HFP+2) LCDDOTCK cycles.
It is only a minor issue. I also changed all boards using atmel_lcdfb
I found to respect the new calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This four year old subsystem does not have a single in-tree user
not even in staging and as far as I know also none out-of-tree.
I think that justifies removing it which cleans the config up.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Acked-by: James Simmons <jsimmons@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org>
Shawn Guo [Thu, 10 Nov 2011 08:39:32 +0000 (16:39 +0800)]
arm/imx: fix imx6q mmc error when mounting rootfs
The following error is seen in some case when mounting rootfs from
SD/MMC cards.
Waiting for root device /dev/mmcblk0p1...
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 SDC 3.74 GiB
mmcblk0: p1
mmc1: Timeout waiting for hardware interrupt.
mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 3678225
Buffer I/O error on device mmcblk0p1, logical block 458754
lost page write due to I/O error on mmcblk0p1
This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
Arne Jansen [Fri, 11 Nov 2011 13:17:10 +0000 (08:17 -0500)]
Btrfs: handle bio_add_page failure gracefully in scrub
Currently scrub fails with ENOMEM when bio_add_page fails. Unfortunately
dm based targets accept only one page per bio, thus making scrub always
fails. This patch just submits the current bio when an error is encountered
and starts a new one.
Signed-off-by: Arne Jansen <sensille@gmx.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 11 Nov 2011 11:17:43 +0000 (11:17 +0000)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: Fix bandwidth calculation for DisplayPort
drm/nouveau: by default use low bpp framebuffer on low memory cards
drm/nv10: Change the BO size threshold determining the memory placement range.
drm/nvc0: enable acceleration for nvc1 by default
drm/nvc0/gr: fixup the mmio list register writes for 0xc1
drm/nvc1: hacky workaround to fix accel issues
drm/nvc0/gr: fix some bugs in grctx generation
drm/nvc0: enable acceleration on 0xc8 by default
drm/nvc0/vram: skip disabled PBFB subunits
drm/nv40/pm: fix issues on igp chipsets, which don't have memory
drm/nouveau: testing the wrong variable
drm/nvc0/vram: storage type 0xc3 is not compressed
drm/nv50: fix stability issue on NV86.
drm/nouveau: initialize chan->fence.lock before use
drm/nv50/vram: fix incorrect detection of bank count on newer chipsets
drm/nv50/gr: typo fix, how about we not reset fifo during graph init?
drm/nv50/bios: fixup mpll programming from the init table parser
drm/nouveau: fix oops if i2c bus not found in nouveau_i2c_identify()
drm: make sure drm_vblank_init() has been called before touching vbl_lock
Ilija Hadzic [Mon, 31 Oct 2011 17:11:57 +0000 (13:11 -0400)]
drm: add some comments to drm_wait_vblank and drm_queue_vblank_event
during the review of the fix for locks problems in drm_wait_vblank,
a couple of false concerns were raised about how the drm_vblank_get
and drm_vblank_put are used in this function; it turned out that the
code is correct and that it cannot be simplified
add a few comments to explain non-obvious flows in the code,
to prevent "false alarms" in the future
v2: incorporate comments received from Daniel Vetter
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ilija Hadzic [Mon, 31 Oct 2011 21:46:18 +0000 (17:46 -0400)]
drm: do not sleep on vblank while holding a mutex
drm_wait_vblank must be DRM_UNLOCKED because otherwise it
will grab the drm_global_mutex and then go to sleep until the vblank
event it is waiting for. That can wreck havoc in the windowing system
because if one process issues this ioctl, it will block all other
processes for the duration of all vblanks between the current and the
one it is waiting for. In some cases it can block the entire windowing
system.
v2: incorporate comments received from Daniel Vetter and
Michel Daenzer.
v3/v4: after a lengty discussion with Daniel Vetter, it was concluded
that the only thing not yet protected with locks and atomic
ops is the write to dev->last_vblank_wait. It's only used in a
debug file in proc, and the current code already employs no
correct locking: the proc file only takes dev->struct_mutex,
whereas drm_wait_vblank implicitly took the drm_global_mutex.
Given all this, it's not worth bothering to try to fix
the locks at this time.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jesse Barnes [Mon, 7 Nov 2011 18:39:57 +0000 (10:39 -0800)]
drm: try to restore previous CRTC config if mode set fails
We restore the CRTC, encoder, and connector configurations, but if the
mode set failed, the attached display may have been turned off, so we
need to try set_config again to restore things to the way they were.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Paul Bolle [Wed, 9 Nov 2011 00:16:50 +0000 (01:16 +0100)]
drm: drop select of SLOW_WORK
slow-work got killed in commit 181a51f6e0. This means that since v2.6.36
there is no Kconfig symbol SLOW_WORK. Apparently selecting that symbol
is a nop. Drop that select.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Dave Airlie <airlied@redhat.com>
Marcin Slusarz [Wed, 9 Nov 2011 21:20:35 +0000 (22:20 +0100)]
drm: serialize access to list of debugfs files
Nouveau, when configured with debugfs, creates debugfs files for every
channel, so structure holding list of files needs to be protected from
simultaneous changes by multiple threads.
Without this patch it's possible to hit kernel oops in
drm_debugfs_remove_files just by running a couple of xterms with
looped glxinfo.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Thu, 10 Nov 2011 17:57:26 +0000 (18:57 +0100)]
drm/radeon: Make sure CS mutex is held across GPU reset.
This was only the case if the GPU reset was triggered from the CS ioctl,
otherwise other processes could happily enter the CS ioctl and wreak havoc
during the GPU reset.
This is a little complicated because the GPU reset can be triggered from the
CS ioctl, in which case we're already holding the mutex, or from other call
paths, in which case we need to lock the mutex. AFAICT the mutex API doesn't
allow recursive locking or finding out the mutex owner, so we need to handle
this with helper functions which allow recursive locking from the same
process.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
vmwgfx: Initialize clip rect loop correctly in surface dirty
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Magnus Damm [Fri, 11 Nov 2011 05:01:30 +0000 (14:01 +0900)]
ARM: mach-shmobile: cpuidle single/global and last_state fixes
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
projects / mv-sheeva.git / log