Imre Deak [Mon, 21 Nov 2016 19:15:04 +0000 (21:15 +0200)]
drm/i915/lspcon: Ensure AUX CH is awake while in DP Sleep state
Some LSPCON adaptors won't properly wake up in response to an AUX
request after the adaptor was placed to a DP Sink Sleep state (via
writing 0x2 to DP_SET_POWER). Based on the DP 1.4 specification 5.2.5,
the sink may place the AUX CH into a low-power state while in Sleep
state, but should wake it up in response to an AUX request within 1-20ms
(answering with AUX defers while waking it up). As opposed to this at
least the ParadTech PS175 adaptor won't fully wake in response to the
first I2C-over-AUX access and will occasionally ignore the offset in I2C
messages. This can result in accessing the DDC register at offset 0
regardless of the specified offset and the LSPCON detection failing.
To fix this do an initial dummy read from the DPCD area. The PS175 will
defer this access until it's fully woken (taking ~150ms) making sure the
following I2C-over-AUX accesses will work correctly.
Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=98353 Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-2-git-send-email-imre.deak@intel.com
Chris Wilson [Tue, 22 Nov 2016 14:41:21 +0000 (14:41 +0000)]
drm/i915: Stop the machine as we install the wedged submit_request handler
In order to prevent a race between the old callback submitting an
incomplete request and i915_gem_set_wedged() installing its nop handler,
we must ensure that the swap occurs when the machine is idle
(stop_machine).
Chris Wilson [Tue, 22 Nov 2016 14:41:20 +0000 (14:41 +0000)]
drm/i915: Complete requests in nop_submit_request
Since the submit/execute split in commit d55ac5bf97c6 ("drm/i915: Defer
transfer onto execution timeline to actual hw submission") the
global seqno advance was deferred until the submit_request callback.
After wedging the GPU, we were installing a nop_submit_request handler
(to avoid waking up the dead hw) but I had missed converting this over
to the new scheme. Under the new scheme, we have to explicitly call
i915_gem_submit_request() from the submit_request handler to mark the
request as on the hardware. If we don't the request is always pending,
and any waiter will continue to wait indefinitely and hangcheck will not
be able to resolve the lockup.
References: https://bugs.freedesktop.org/show_bug.cgi?id=98748
Testcase: igt/gem_eio/in-flight Fixes: d55ac5bf97c6 ("drm/i915: Defer transfer onto execution timeline to actual hw submission") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161122144121.7379-3-chris@chris-wilson.co.uk
Chris Wilson [Tue, 22 Nov 2016 14:41:19 +0000 (14:41 +0000)]
drm/i915: Disable hangcheck when wedged
If the gpu reset fails and the machine is terminally wedged, further
hangchecks achieve nothing but noise. Disable them, with a corollary
that we re-enable hangchecking after a successful GPU reset in case the
user is artificially bringing the machine back to life through the debug
interface.
Chris Wilson [Tue, 22 Nov 2016 14:41:18 +0000 (14:41 +0000)]
drm/i915: Don't deref context->file_priv ERR_PTR upon reset
When a user context is closed, it's file_priv backpointer is replaced by
ERR_PTR(-EBADF); be careful not to chase this invalid pointer after a
hang and a GPU reset.
Robert Bragg [Mon, 7 Nov 2016 19:49:57 +0000 (19:49 +0000)]
drm/i915: Add a kerneldoc summary for i915_perf.c
In particular this tries to capture for posterity some of the early
challenges we had with using the core perf infrastructure in case we
ever want to revisit adapting perf for device metrics.
Consistent with the kernel.perf_event_paranoid sysctl option that can
allow non-root users to access system wide cpu metrics, this can
optionally allow non-root users to access system wide OA counter metrics
from Gen graphics hardware.
Robert Bragg [Mon, 7 Nov 2016 19:49:53 +0000 (19:49 +0000)]
drm/i915: advertise available metrics via sysfs
Each metric set is given a sysfs entry like:
/sys/class/drm/card0/metrics/<guid>/id
This allows userspace to enumerate the specific sets that are available
for the current system. The 'id' file contains an unsigned integer that
can be used to open the associated metric set via
DRM_IOCTL_I915_PERF_OPEN. The <guid> is a globally unique ID for a
specific OA unit register configuration that can be reliably used by
userspace as a key to lookup corresponding counter meta data and
normalization equations.
The guid registry is currently maintained as part of gputop along with
the XML metric set descriptions and code generation scripts, ref:
Robert Bragg [Mon, 7 Nov 2016 19:49:52 +0000 (19:49 +0000)]
drm/i915: Enable i915 perf stream for Haswell OA unit
Gen graphics hardware can be set up to periodically write snapshots of
performance counters into a circular buffer via its Observation
Architecture and this patch exposes that capability to userspace via the
i915 perf interface.
v2:
Make sure to initialize ->specific_ctx_id when opening, without
relying on _pin_notify hook, in case ctx already pinned.
v3:
Revert back to pinning ctx upfront when opening stream, removing
need to hook in to pinning and to update OACONTROL on the fly.
Signed-off-by: Robert Bragg <robert@sixbynine.org> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Sourab Gupta <sourab.gupta@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161107194957.3385-7-robert@sixbynine.org
Robert Bragg [Mon, 7 Nov 2016 19:49:51 +0000 (19:49 +0000)]
drm/i915: Add 'render basic' Haswell OA unit config
Adds a static OA unit, MUX + B Counter configuration for basic render
metrics on Haswell. This is auto generated from an XML
description of metric sets, currently maintained in gputop, ref:
Robert Bragg [Tue, 8 Nov 2016 12:51:48 +0000 (12:51 +0000)]
drm/i915: don't whitelist oacontrol in cmd parser
Being able to program OACONTROL from a non-privileged batch buffer is
not sufficient to be able to configure the OA unit. This was originally
allowed to help enable Mesa to expose OA counters via the
INTEL_performance_query extension, but the current implementation based
on programming OACONTROL via a batch buffer isn't able to report useable
data without a more complete OA unit configuration. Mesa handles the
possibility that writes to OACONTROL may not be allowed and so only
advertises the extension after explicitly testing that a write to
OACONTROL succeeds. Based on this; removing OACONTROL from the whitelist
should be ok for userspace.
Removing this simplifies adding a new kernel api for configuring the OA
unit without needing to consider the possibility that userspace might
trample on OACONTROL state which we'd like to start managing within
the kernel instead. In particular running any Mesa based GL application
currently results in clearing OACONTROL when initializing which would
disable the capturing of metrics.
v2:
This bumps the command parser version from 8 to 9, as the change is
visible to userspace.
Robert Bragg [Mon, 7 Nov 2016 19:49:49 +0000 (19:49 +0000)]
drm/i915: return EACCES for check_cmd() failures
check_cmd() is checking whether a command adheres to certain
restrictions that ensure it's safe to execute within a privileged batch
buffer. Returning false implies a privilege problem, not that the
command is invalid.
The distinction makes the difference between allowing the buffer to be
executed as an unprivileged batch buffer or returning an EINVAL error to
userspace without executing anything.
In a case where userspace may want to test whether it can successfully
write to a register that needs privileges the distinction may be
important and an EINVAL error may be considered fatal.
In particular this is currently true for Mesa, which includes a test for
whether OACONTROL can be written too, but Mesa treats any error when
flushing a batch buffer as fatal, calling exit(1).
As it is currently Mesa can gracefully handle a failure to write to
OACONTROL if the command parser is disabled, but if we were to remove
OACONTROL from the parser's whitelist then the returned EINVAL would
break Mesa applications as they attempt an OACONTROL write.
This bumps the command parser version from 7 to 8, as the change is
visible to userspace.
Robert Bragg [Mon, 7 Nov 2016 19:49:48 +0000 (19:49 +0000)]
drm/i915: rename OACONTROL GEN7_OACONTROL
OACONTROL changes quite a bit for gen8, with some bits split out into a
per-context OACTXCONTROL register. Rename now before adding more gen7 OA
registers
Robert Bragg [Mon, 7 Nov 2016 19:49:47 +0000 (19:49 +0000)]
drm/i915: Add i915 perf infrastructure
Adds base i915 perf infrastructure for Gen performance metrics.
This adds a DRM_IOCTL_I915_PERF_OPEN ioctl that takes an array of uint64
properties to configure a stream of metrics and returns a new fd usable
with standard VFS system calls including read() to read typed and sized
records; ioctl() to enable or disable capture and poll() to wait for
data.
Records read all start with a common { type, size } header with
DRM_I915_PERF_RECORD_SAMPLE being of most interest. Sample records
contain an extensible number of fields and it's the
DRM_I915_PERF_PROP_SAMPLE_xyz properties given when opening that
determine what's included in every sample.
No specific streams are supported yet so any attempt to open a stream
will return an error.
v2:
use i915_gem_context_get() - Chris Wilson
v3:
update read() interface to avoid passing state struct - Chris Wilson
fix some rebase fallout, with i915-perf init/deinit
v4:
s/DRM_IORW/DRM_IOW/ - Emil Velikov
Mika Kuoppala [Fri, 18 Nov 2016 13:10:47 +0000 (15:10 +0200)]
drm/i915: Add per client max context ban limit
If we have a bad client submitting unfavourably across different
contexts, creating new ones, the per context scoring of badness
doesn't remove the root cause, the offending client.
To counter, keep track of per client context bans. Deny access if
client is responsible for more than 3 context bans in
it's lifetime.
v2: move ban check to context create ioctl (Chris)
v3: add commentary about hangs needed to reach client ban (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Mika Kuoppala [Wed, 16 Nov 2016 15:20:32 +0000 (17:20 +0200)]
drm/i915: Add bannable context parameter
Now when driver has per context scoring of 'hanging badness'
and also subsequent hangs during short windows are allowed,
if there is progress made in between, it does not make sense
to expose a ban timing window as a context parameter anymore.
Let the scoring be the sole indicator for ban policy and substitute
ban period context parameter as a boolean to get/set context
bannable property.
v2: allow non root to opt into being banned (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Mika Kuoppala [Wed, 16 Nov 2016 15:20:31 +0000 (17:20 +0200)]
drm/i915: Use request retirement as context progress
As hangcheck score was removed, the active decay of score
was removed also. This removed feature for hangcheck to detect
if the gpu client was accidentally or maliciously causing intermittent
hangs. Reinstate the scoring as a per context property, so that if
one context starts to act unfavourably, ban it.
v2: ban_period_secs as a gate to score check (Chris)
v3: decay in proper spot. scores as tunables (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Mika Kuoppala [Fri, 18 Nov 2016 13:09:04 +0000 (15:09 +0200)]
drm/i915: Decouple hang detection from hangcheck period
Hangcheck state accumulation has gained more steps
along the years, like head movement and more recently the
subunit inactivity check. As the subunit sampling is only
done if the previous state check showed inactivity, we
have added more stages (and time) to reach a hang verdict.
Asymmetric engine states led to different actual weight of
'one hangcheck unit' and it was demonstrated in some
hangs that due to difference in stages, simpler engines
were accused falsely of a hang as their scoring was much
more quicker to accumulate above the hang treshold.
To completely decouple the hangcheck guilty score
from the hangcheck period, convert hangcheck score to a
rough period of inactivity measurement. As these are
tracked as jiffies, they are meaningful also across
reset boundaries. This makes finding a guilty engine
more accurate across multi engine activity scenarios,
especially across asymmetric engines.
We lose the ability to detect cross batch malicious attempts
to hinder the progress. Plan is to move this functionality
to be part of context banning which is more natural fit,
later in the series.
v2: use time_before macros (Chris)
reinstate the pardoning of moving engine after hc (Chris)
v3: avoid global state for per engine stall detection (Chris)
v4: take timeline last retirement into account (Chris)
v5: do debug print on pardoning, split out retirement timestamp (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Mika Kuoppala [Wed, 16 Nov 2016 15:20:29 +0000 (17:20 +0200)]
drm/i915: Split up hangcheck phases
In order to simplify hangcheck state keeping, split hangcheck
per engine loop in three phases: state load, action, state save.
Add few more hangcheck actions to separate between seqno, head
and subunit movements. This helps to gather all the hangcheck
actions under a single switch umbrella.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
A.Sunil Kamath [Sun, 20 Nov 2016 17:50:26 +0000 (23:20 +0530)]
drm/i915: Use num_scalers instead of SKL_NUM_SCALERS in debugfs
Better to use num_scaler itself while printing scaler_info.
This fixes a bug of printing information for the missing
second scaler on pipe C for SKL platform.
Chris Wilson [Mon, 21 Nov 2016 11:07:59 +0000 (11:07 +0000)]
drm/i915: Add a warning on shutdown if signal threads still active
When unloading the module, it is expected that we have finished
executing all requests and so the signal threads should be idle. Add a
warning in case there are any residual requests in the signaler rbtrees
at that point.
Chris Wilson [Fri, 18 Nov 2016 21:17:47 +0000 (21:17 +0000)]
drm/i915: Skip final clflush if LLC is coherent
If the LLC is coherent with the object, we do not need to worry about
whether main memory and cache mismatch when we hand the object back to
the system.
Chris Wilson [Fri, 18 Nov 2016 21:17:46 +0000 (21:17 +0000)]
drm/i915: Always flush the dirty CPU cache when pinning the scanout
Currently we only clflush the scanout if it is in the CPU domain. Also
flush if we have a pending CPU clflush. We also want to treat the
dirtyfb path similar, and flush any pending writes there as well.
v2: Only send the fb flush message if flushing the dirt on flip
v3: Make flush-for-flip and dirtyfb look more alike since they serve
similar roles as end-of-frame marker.
Let's add a couple more BUG_ONs before this to ascertain that the request
did make it to hardware. The impossible part of this stacktrace is that
request must have been considered completed by the i915_request_wait()
before we tried to retire it.
Matthew Auld [Fri, 18 Nov 2016 17:02:16 +0000 (17:02 +0000)]
drm/i915: i915_pages_create_for_stolen should return err ptr
When gathering the pages from our backing storage we expect get_pages()
to either give us our sg_table or an err ptr. However when gathering our
fake pages for stolen memory we may return NULL in the event of a
failure. To prevent any funny business we should therefore return the
proper err ptr value.
Chris Wilson [Tue, 15 Nov 2016 16:46:20 +0000 (16:46 +0000)]
drm/i915: Be more careful to drop the GT wakeref
Since we can retire requests from multiple paths, we cannot assume that
i915_gem_retire_requests() is the sole path on which we can transition
to gt.active_requests == 0. A consequence of this is that we would skip
the function if we had already retired all the requests and not
scheduled the idle worker.
This is fallout from changing the routine from considering active_engines
(for which it was the only consumer) to active_requests.
v2: Move kicking the idle working to i915_gem_request_retire() otherwise
we could postpone the idle callback everytime we called retire_requests
even though we did no work.
v3: We only need to move the idle work kicking!
v4: Drop the BUG_ON(!awake) as we may be called from the shrinker in the
middle of constructing a request before we have marked the device awake.
v5: Add a BUG_ON() for active_requests underflow upon retirement (Joonas)
Chris Wilson [Wed, 16 Nov 2016 19:07:04 +0000 (19:07 +0000)]
drm/i915: Move frontbuffer CS write tracking from ggtt vma to object
I tried to avoid having to track the write for every VMA by only
tracking writes to the ggtt. However, for the purposes of frontbuffer
tracking this is insufficient as we need to invalidate around writes not
just to the the ggtt but all aliased ppgtt views of the framebuffer. By
moving the critical section to the object and only doing so for
framebuffer writes we can reduce the tracking even further by only
watching framebuffers and not vma.
Matthew Auld [Thu, 17 Nov 2016 21:04:10 +0000 (21:04 +0000)]
drm/i915: add i915_address_space_fini
We already have an i915_address_space_init, so for symmetry we should
also have a _fini, plus we already open code it twice. This then also
fixes a bug where we leak the timeline for the ggtt vm.
v2: don't forget about the struct_mutex for the ggtt path.
Chris Wilson [Thu, 17 Nov 2016 15:58:46 +0000 (15:58 +0000)]
drm/i915: Add a few more sanity checks for stolen handling
We should never be called via obj->ops->release() on anything other than
a fully formed stolen object, so raise that to an assert. In the process
tidy up a comment and variable no longer used outside of a conditional
BUG.
Chris Wilson [Wed, 16 Nov 2016 12:26:18 +0000 (12:26 +0000)]
drm/i915: Remove stolen object spam
We don't spam the debug when we create a normal object, nor when we
allocate their pages. Yet we do for stolen objects, and since these are
quite frequently used (at least once per context), the resulting spam
floods the dmesg in CI.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Chris Wilson [Wed, 9 Nov 2016 10:45:07 +0000 (10:45 +0000)]
drm/i915: Demote i915_gem_open() debugging from DRIVER to USER
We use DRM_DEBUG() when reporting on user actions, to try and keep
intentional errors out of the CI dmesg. Demote the debug from
i915_gem_open() similarly so that it is only apparent with drm.debug & 1
like its brethren.
Tvrtko Ursulin [Thu, 17 Nov 2016 10:00:05 +0000 (10:00 +0000)]
drm/i915: Make scaler updates less chatty
It looks to me skl_update_scaler will already log interesting
debug messages when the state transitions or there is an error.
In this case it feels we can remove the two unconditional
debug messages which happen immediately before calling
skl_update_scaler. This way we get rid of the sole debug
message when switching virtual terminals for example.
Daniel Vetter [Thu, 17 Nov 2016 13:46:39 +0000 (14:46 +0100)]
Merge tag 'gvt-next-2016-11-17' of https://github.com/01org/gvt-linux into drm-intel-next-queued
From Zhenyu Wang:
gvt-next-2016-11-17
- Fix lock order issue found in guest stress test
- Fix several MMIO handlers to correct behavior
- Fix crash for vgpu execlist reset and memleak
- Fix a possible conflict for unresolved vfio mdev dependency
- other misc fixes
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tvrtko Ursulin [Thu, 17 Nov 2016 09:02:43 +0000 (09:02 +0000)]
drm/i915: Fix gen9 forcewake range table
Commit 0dd356bb6ff5 ("drm/i915: Eliminate Gen9 special case")
accidentaly dropped a MMIO range between 0xc000 to 0xcfff out
of the blitter forcewake domain. Fix it.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: 0dd356bb6ff5 ("drm/i915: Eliminate Gen9 special case") Reported-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1479373363-16528-1-git-send-email-tvrtko.ursulin@linux.intel.com
drm/i915: set DIDL using the ACPI video output device _ADR method return.
which went out of its way to cater to a specific BIOS, setting up DIDL
based on _ADR method. Perhaps that approach worked on that specific
machine, but on the machines I checked the _ADR method invents the
device identifiers out of thin air if DIDL has not been set. The source
for _ADR is also supposed to be the DIDL set by the driver, not the
other way around.
With this, we'll also limit the number of outputs to what the driver
actually has.
A side effect of this change is that the DIDL, and by proxy CADL, will
be initialized in the order of the connector list. That, in turn, has
internal panels in front, ensuring they're included in the DIDL and CADL
lists. Hopefully this ensures the BIOS does not block backlight hotkey
events, thinking the internal panel is off.
v2: do not set ACPI_DEVICE_ID_SCHEME in the device id (Peter Wu)
v3: Rebase
Cc: Peter Wu <peter@lekensteyn.nl> Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com> Cc: Jan-Marek Glogowski <glogow@fbihome.de> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Cc: Paolo Stivanin <paolostivanin@fastmail.fm> Tested-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com> Tested-by: Paolo Stivanin <paolostivanin@fastmail.fm> Tested-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Reviewed-and-tested-by: Peter Wu <peter@lekensteyn.nl> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/9660d29cf310c17bbf4d58c0e09d5b047446e2d5.1479295490.git.jani.nikula@intel.com
Min He [Wed, 16 Nov 2016 14:05:04 +0000 (22:05 +0800)]
drm/i915: fix the dequeue logic for single_port_submission context
For a single_port_submission context, GVT expects that it can only be
submitted to port 0, and there shouldn't be any other context in port 1
at the same time. This is required by GVT-g context to have an opportunity
to save/restore some non-hw context render registers.
This patch is to workaround GVT-g.
v2: optimized code by following Chris's advice, and added more comments to
explain the patch.
v3: followed the coding style.
Instead of partially depending on vfio pin/unpin pages interface if
mdev is available, which would result in failure if vfio is not
on. But replace with a wrapper which need to be fixed till mdev
support got fully merged.
Cc: Jike Song <jike.song@intel.com> Cc: Xiaoguang Chen <xiaoguang.chen@intel.com> Reviewed-by: Xiaoguang Chen <Xiaoguang.chen@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Dave Airlie [Wed, 16 Nov 2016 22:02:46 +0000 (08:02 +1000)]
Merge tag 'drm-misc-next-2016-11-16' of git://anongit.freedesktop.org/git/drm-misc into drm-next
Another pile of misc:
- Explicit fencing for atomic! Big thanks to Gustavo, Sean, Rob 3x, Brian
and anyone else I've forgotten to make this happen.
- roll out fbdev helper ops to drivers (Stefan Christ)
- last bits of drm_crtc split-up&kerneldoc
- some drm_irq.c crtc functions cleanup
- prepare_fb helper for cma, works correctly with explicit fencing (Marek
Vasut)
- misc small patches all over
* tag 'drm-misc-next-2016-11-16' of git://anongit.freedesktop.org/git/drm-misc: (51 commits)
drm/fence: add out-fences support
drm/fence: add fence timeline to drm_crtc
drm/fence: add in-fences support
drm/bridge: analogix_dp: return error if transfer none byte
drm: drm_irq.h header cleanup
drm/irq: Unexport drm_vblank_on/off
drm/irq: Unexport drm_vblank_count
drm/irq: Make drm_vblank_pre/post_modeset internal
drm/nouveau: Use drm_crtc_vblank_off/on
drm/amdgpu: Use drm_crtc_vblank_on/off for dce6
drm/color: document NULL values and default settings better
drm: Drop externs from drm_crtc.h
drm: Move tile group code into drm_connector.c
drm: Extract drm_mode_config.[hc]
Revert "drm: Add aspect ratio parsing in DRM layer"
Revert "drm: Add and handle new aspect ratios in DRM layer"
drm/print: Move kerneldoc next to definition
drm: Consolidate dumb buffer docs
drm: Clean up kerneldoc for struct drm_driver
drm: Extract drm_drv.h
...
Jonas Pfeil [Mon, 7 Nov 2016 23:18:39 +0000 (00:18 +0100)]
drm/vc4: Add fragment shader threading support
FS threading brings performance improvements of 0-20% in glmark2.
The validation code checks for thread switch signals and ensures that
the registers of the other thread are not touched, and that our clamps
are not live across thread switches. It also checks that the
threading and branching instructions do not interfere.
(Original patch by Jonas, changes by anholt for style cleanup,
removing validation the kernel doesn't need to do, and adding the flag
for userspace).
v2: Minor style fixes from checkpatch.
Signed-off-by: Jonas Pfeil <pfeiljonas@gmx.de> Signed-off-by: Eric Anholt <eric@anholt.net>
Chris Wilson [Wed, 16 Nov 2016 15:27:21 +0000 (15:27 +0000)]
drm/i915/execlists: Use a local lock for dfs_link access
Avoid requiring struct_mutex for exclusive access to the temporary
dfs_link inside the i915_dependency as not all callers may want to touch
struct_mutex. So rather than force them to take a highly contended
lock, introduce a local lock for the execlists schedule operation.
Reported-by: David Weinehall <david.weinehall@linux.intel.com> Fixes: 9a151987d709 ("drm/i915: Add execution priority boosting for mmioflips") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161116152721.11053-1-chris@chris-wilson.co.uk Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Gustavo Padovan [Wed, 16 Nov 2016 13:00:21 +0000 (22:00 +0900)]
drm/fence: add out-fences support
Support DRM out-fences by creating a sync_file with a fence for each CRTC
that sets the OUT_FENCE_PTR property.
We use the out_fence pointer received in the OUT_FENCE_PTR prop to send
the sync_file fd back to userspace.
The sync_file and fd are allocated/created before commit, but the
fd_install operation only happens after we know that commit succeed.
v2: Comment by Rob Clark:
- Squash commit that adds DRM_MODE_ATOMIC_OUT_FENCE flag here.
Comment by Daniel Vetter:
- Add clean up code for out_fences
v3: Comments by Daniel Vetter:
- create DRM_MODE_ATOMIC_EVENT_MASK
- userspace should fill out_fences_ptr with the crtc_ids for which
it wants fences back.
v4: Create OUT_FENCE_PTR properties and remove old approach.
v5: Comments by Brian Starkey:
- Remove extra fence_get() in atomic_ioctl()
- Check ret before iterating on the crtc_state
- check ret before fd_install
- set fence_state to NULL at the beginning
- check fence_state->out_fence_ptr before put_user()
- change order of fput() and put_unused_fd() on failure
- Add access_ok() check to the out_fence_ptr received
- Rebase after fence -> dma_fence rename
- Store out_fence_ptr in the drm_atomic_state
- Split crtc_setup_out_fence()
- return -1 as out_fence with TEST_ONLY flag
v6: Comments by Daniel Vetter
- Add prepare/unprepare_crtc_signaling()
- move struct drm_out_fence_state to drm_atomic.c
- mark get_crtc_fence() as static
Comments by Brian Starkey
- proper set fence_ptr fence_state array
- isolate fence_idx increment
- improve error handling
v7: Comments by Daniel Vetter
- remove prefix from internal functions
- make out_fence_ptr an s64 pointer
- degrade DRM_INFO to DRM_DEBUG_ATOMIC when put_user fail
- fix doc issues
- filter out OUT_FENCE_PTR == NULL and do not fail in this case
- add complete_crtc_signalling()
- krealloc fence_state on demand
Comment by Brian Starkey
- remove unused crtc_state arg from get_out_fence()
v8: Comment by Brian Starkey
- cancel events before check for !fence_state
- convert a few lefovers u64 types for out_fence_ptr
- fix memleak by assign fence_state earlier after realloc
- proper accout num_fences in case of error
v9: Comment by Brian Starkey
- memset last position of fence_state after krealloc
Comments by Sean Paul
- pass install_fds in complete_crtc_signaling() instead of ret
- put_user(-1, fence_ptr) when decoding props
v10: Comment by Brian Starkey
- remove unneeded num_fences increment on error path
- kfree fence_state after installing fences fd
v11: rebase against latest drm-misc
v12: rebase again against latest drm-misc
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Reviewed-by: Brian Starkey <brian.starkey@arm.com> (v10) Reviewed-by: Sean Paul <seanpaul@chromium.org> Tested-by: Robert Foss <robert.foss@collabora.com> (v10)
[danvet: Appease checkpatch.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1479301221-13056-1-git-send-email-gustavo@padovan.org
Gustavo Padovan [Tue, 15 Nov 2016 14:37:08 +0000 (23:37 +0900)]
drm/fence: add fence timeline to drm_crtc
Create one timeline context for each CRTC to be able to handle out-fences
and signal them. It adds a few members to struct drm_crtc: fence_context,
where we store the context we get from fence_context_alloc(), the
fence seqno and the fence lock, that we pass in fence_init() to be
used by the fence.
v2: Comment by Daniel Stone:
- add BUG_ON() to fence_to_crtc() macro
v3: Comment by Ville Syrjälä
- Use more meaningful name as crtc timeline name
v4: Comments by Brian Starkey
- Use even more meaninful name for the crtc timeline
- add doc for timeline_name
Comment by Daniel Vetter
- use in-line style for comments
- rebase after fence -> dma_fence rename
v5: Comment by Daniel Vetter
- Add doc for drm_crtc_fence_ops
v6: Comment by Chris Wilson
- Move fence_to_crtc to drm_crtc.c
- Move export of drm_crtc_fence_ops to drm_crtc_internal.h
Praveen Paneri [Tue, 15 Nov 2016 17:19:20 +0000 (22:49 +0530)]
drm/i915/bxt: Broxton decoupled MMIO
Decoupled MMIO is an alternative way to access forcewake domain
registers, which requires less cycles for a single read/write and
avoids frequent software forcewake.
This certainly gives advantage over the forcewake as this new
mechanism “decouples” CPU cycles and allow them to complete even
when GT is in a CPD (frequency change) or C6 state.
This can co-exist with forcewake and we will continue to use forcewake
as appropriate. E.g. 64-bit register writes to avoid writing 2 dwords
separately and land into funny situations.
v2:
- Moved platform check out of the function and got rid of duplicate
functions to find out decoupled power domain (Chris)
- Added a check for forcewake already held and skipped decoupled
access (Chris)
- Skipped writing 64 bit registers through decoupled MMIO (Chris)
v3:
- Improved commit message with more info on decoupled mmio (Tvrtko)
- Changed decoupled operation to enum and used u32 instead of
uint_32 data type for register offset (Tvrtko)
- Moved HAS_DECOUPLED_MMIO to device info (Tvrtko)
- Added lookup table for converting fw_engine to pd_engine (Tvrtko)
- Improved __gen9_decoupled_read and __gen9_decoupled_write
routines (Tvrtko)
v4:
- Fixed alignment and variable names (Chris)
- Write GEN9_DECOUPLED_REG0_DW1 register in just one go (Zhe Wang)
v5:
- Changed HAS_DECOUPLED_MMIO() argument name to dev_priv (Tvrtko)
- Sanitize info->had_decoupled_mmio at init (Chris)
Gustavo Padovan [Tue, 15 Nov 2016 13:06:39 +0000 (22:06 +0900)]
drm/fence: add in-fences support
There is now a new property called IN_FENCE_FD attached to every plane
state that receives sync_file fds from userspace via the atomic commit
IOCTL.
The fd is then translated to a fence (that may be a fence_array
subclass or just a normal fence) and then used by DRM to fence_wait() for
all fences in the sync_file to signal. So it only commits when all
framebuffers are ready to scanout.
v2: Comments by Daniel Vetter:
- remove set state->fence = NULL in destroy phase
- accept fence -1 as valid and just return 0
- do not call fence_get() - sync_file_fences_get() already calls it
- fence_put() if state->fence is already set, in case userspace
set the property more than once.
v3: WARN_ON if fence is set but state has no FB
v4: Comment from Maarten Lankhorst
- allow set fence with no related fb
v5: rename FENCE_FD to IN_FENCE_FD
v6: Comments by Daniel Vetter:
- rename plane_state->in_fence back to "fence"
- re-introduce WARN_ON if fence set but no fb
- rebase after fence -> dma_fence rename
v7: Comments by Brian Starkey
- set state->fence to NULL when duplicating the state
- fail if IN_FENCE_FD was already set
v8: rebase against latest drm-misc
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Reviewed-by: Brian Starkey <brian.starkey@arm.com> Reviewed-by: Sean Paul <seanpaul@chromium.org> Tested-by: Robert Foss <robert.foss@collabora.com>
[danvet: Rebase onto extracted drm_mode_config.[hc].] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jianqun Xu [Wed, 16 Nov 2016 00:13:39 +0000 (08:13 +0800)]
drm/bridge: analogix_dp: return error if transfer none byte
Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that were transferred, or a negative error-code on failure. Helpers
propagate errors from the .transfer() function, with the exception of
the -EBUSY error, which causes a transaction to be retried. On a short,
helpers will return -EPROTO to make it simpler to check for failure.
The analogix_dp_transfer will return num_transferred, but if there is none
byte been transferred, the return value will be 0, which means success, we
should return error-code if transfer none byte.
for (retry = 0; retry < 32; retry++) {
err = aux->transfer(aux, &msg);
if (err < 0) {
if (err == -EBUSY)
continue;
Pei Zhang [Wed, 16 Nov 2016 11:05:50 +0000 (19:05 +0800)]
drm/i915/gvt: check workload empty before real scan
This patch will fix warning log print during command scan caused by
empty workload (ring head equals tail). This patch avoid going into
real scan process if workload is empty. It's guest's responsibility
to make sure if an empty workload is proper to submit to HW.
[v2] modify the patch description. It's a fix, not a w/a.
Signed-off-by: Pei Zhang <pei.zhang@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Dave Airlie [Tue, 15 Nov 2016 23:39:55 +0000 (09:39 +1000)]
Merge tag 'sunxi-drm-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next
sun4i-drm changes for 4.10
Support for the Allwinner A31 SoC display engine using the sun4i-drm
driver.
* tag 'sunxi-drm-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drm/sun4i: Add a few formats
drm/sun4i: Add compatible strings for A31/A31s display pipelines
drm/sun4i: Add compatible string for A31/A31s TCON (timing controller)
drm/sun4i: tcon: Move SoC specific quirks to a DT matched data structure
drm/sun4i: sun6i-drc: Support DRC on A31 and A31s
Daniel Vetter [Mon, 14 Nov 2016 09:02:53 +0000 (10:02 +0100)]
drm/irq: Unexport drm_vblank_count
No one outside of drm_irq.c should ever need this. The correct way to
implement get_vblank_count for hw lacking a vblank counter is
drm_vblank_no_hw_counter. Fix this up in mtk, which is the only
offender left over.
Daniel Vetter [Mon, 14 Nov 2016 09:02:52 +0000 (10:02 +0100)]
drm/irq: Make drm_vblank_pre/post_modeset internal
Now that all drivers are switched over to drm_crtc_vblank_on/off we
can relegate pre/post_modeset to the purely drm_irq.c internal role of
supporting old ums userspace.
As usual switch to the drm_legacy_ prefix to make it clear this is
for old drivers only.
v2: Rebase on top of Thierry's s/int crtc/unsigned int pipe/ changes.
Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Daniel Vetter [Tue, 15 Nov 2016 21:58:19 +0000 (22:58 +0100)]
drm/nouveau: Use drm_crtc_vblank_off/on
With atomic nv50+ is already converted over to them, but the old
display code is still using it. Found in a 2 year old patch I have
lying around to un-export these old helpers!
v2: Drop the hand-rolled versions from resume/suspend code. Now that
crtc callbacks do this, we don't need a special case for s/r anymore.
v3: Remove unused variables.
v4: Don't remove drm_crtc_vblank_off from suspend paths, non-atomic
nouveau still needs that. But still switch to drm_crtc_vblank_off
since drm_vblank_off will disappear.
Daniel Vetter [Mon, 14 Nov 2016 09:02:50 +0000 (10:02 +0100)]
drm/amdgpu: Use drm_crtc_vblank_on/off for dce6
This old code pattern was reintroduced in
Author: Ken Wang <Qingqing.Wang@amd.com>
Date: Tue Jan 19 14:03:24 2016 +0800
drm/amdgpu: add display controller implementation for si v10
Realign it with later display code. Tsk, tsk for massive copypasting
;-)
Cc: Christian König <christian.koenig@amd.com> Cc: Ken Wang <Qingqing.Wang@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Christian König <christian.koenig@amd.com> for the whole series. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161114090255.31595-1-daniel.vetter@ffwll.ch
Adding new mode flags willy nilly breaks existing userspace. We need to
coordinate this better, potentially with a new client cap that only
exposes the aspect ratio flags when userspace is prepared for them
(similar to what we do with stereo 3D modes).
This also broke things so that we would always send out VIC==0 in
the AVI infoframe unless the user specified an aspect ratio via
the mode flags. And the automagic RGB full vs. limited range
handling was similartly broken as the user mode would never match
any CEA mode.
Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Lin, Jia <lin.a.jia@intel.com> Cc: Akashdeep Sharma <akashdeep.sharma@intel.com> Cc: Jim Bride <jim.bride@linux.intel.com> Cc: Jose Abreu <Jose.Abreu@synopsys.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1478176304-6743-2-git-send-email-ville.syrjala@linux.intel.com
Adding new mode flags willy nilly breaks existing userspace. We need to
coordinate this better, potentially with a new client cap that only
exposes the aspect ratio flags when userspace is prepared for them
(similar to what we do with stereo 3D modes).
Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Lin, Jia <lin.a.jia@intel.com> Cc: Akashdeep Sharma <akashdeep.sharma@intel.com> Cc: Jim Bride <jim.bride@linux.intel.com> Cc: Jose Abreu <Jose.Abreu@synopsys.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1478176304-6743-1-git-send-email-ville.syrjala@linux.intel.com
dev_priv->hw_ddb is only used by skl_update_crtcs, but the ddb
allocation for each pipe is calculated in crtc_state.
We can rid of the global member by looking at crtc_state.
Do this by saving all active old ddb allocations from the old crtc_state
in an array, and then point them to the new allocation every time we update
a crtc.
This will allow us to keep track of the intermediate ddb allocations,
which is what hw_ddb was previously used for. With hw_ddb gone all
SKL-style watermark values are properly maintained only in crtc_state.
projects / linux-beck.git / log