James Smart [Fri, 24 Mar 2017 03:41:27 +0000 (20:41 -0700)]
nvme_fc: Clean up host fcpio done status handling
As Dan Carpenter pointed out: mixing 16-bit nvme status with 32-bit
error status from driver. Corrected comment on fcp request struct
status field, and converted done routine to explicitly set nvme status
codes for nvme status.
Signed-off-by: James Smart <james.smart@broadcom.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
James Smart [Fri, 24 Mar 2017 03:41:22 +0000 (20:41 -0700)]
nvme_fc: Sync FC-NVME header with standard
Update FC-NVME definitions to match FC-NVME r1.14 (16-020vB) plus
change voted in by 2/22 FC-NVME Adhoc (see HOSTID below).
Includes the following:
- Addition of "status_code" field to ERSP IU
- Addition of FC-NVME LS RJT reason_codes and reason_explanations
- CreateAssociation payload, HostID field shortened to 16 bytes
Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
Sagi Grimberg [Sat, 18 Mar 2017 18:58:29 +0000 (20:58 +0200)]
nvme-rdma: Support ctrl_loss_tmo
Before scheduling a reconnect attempt, check
nr_reconnects against max_reconnects, if not
exhausted (or max_reconnects is not -1), schedule
a reconnect attempts, otherwise schedule ctrl
removal.
Sagi Grimberg [Sat, 18 Mar 2017 18:52:36 +0000 (20:52 +0200)]
nvme-fabrics: Allow ctrl loss timeout configuration
When a host sense that its controller session is damaged,
it tries to re-establish it periodically (reconnect every
reconnect_delay). It may very well be that the controller
is gone and never coming back, in this case the host will
try to reconnect forever.
Add a ctrl_loss_tmo to bound the number of reconnect attempts
to a specific controller (default to a reasonable 10 minutes).
The timeout configuration is actually translated into number of
reconnect attempts and not a schedule on its own but rather
divided with reconnect_delay. This is useful to prevent
racing flows of remove and reconnect, and it doesn't really
matter if we remove slightly sooner than what the user requested.
Parav Pandit [Tue, 28 Feb 2017 05:21:33 +0000 (23:21 -0600)]
nvmet: Introduced helper routine for controller status check.
This patch introduces helper function for checking controller
status during admin and io command processing which returns u16
status. As to bring consistency on returning status, other
friend functions also now return u16 status instead of int
to match the spec.
As part of the theseerror log prints in also prints qid on
which command error occured.
Sagi Grimberg [Sun, 5 Feb 2017 19:47:22 +0000 (21:47 +0200)]
net/utils: generic inet_pton_with_scope helper
Several locations in the stack need to handle ipv4/ipv6
(with scope) and port strings conversion to sockaddr.
Add a helper that takes either AF_INET, AF_INET6 or
AF_UNSPEC (for wildcard) to centralize this handling.
Suggested-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
If we are attacked with establishments/teradowns we need to
make sure we do not consume too much system memory. Thus
let ongoing controller teardowns complete before accepting
new controller establishments.
Sagi Grimberg [Thu, 9 Mar 2017 11:26:07 +0000 (13:26 +0200)]
nvme-rdma: handle cpu unplug when re-establishing the controller
If a cpu unplug event has occured, we need to take the minimum
of the provided nr_io_queues and the number of online cpus,
otherwise we won't be able to connect them as blk-mq mapping
won't dispatch to those queues.
Sagi Grimberg [Thu, 9 Mar 2017 11:45:52 +0000 (13:45 +0200)]
nvmet-rdma: Fix a possible uninitialized variable dereference
When handling a new recv command, we grab a new rsp resource and
check for the queue state being live. In case the queue is not in
live state, we simply restore the rsp back to the free list. However
in this flow we didn't set rsp->queue yet, so we cannot dereference it.
Instead, make sure to initialize rsp->queue (and other rsp members)
as soon as possible so we won't reference uninitialized variables.
Sagi Grimberg [Mon, 13 Mar 2017 11:27:51 +0000 (13:27 +0200)]
nvme-loop: handle cpu unplug when re-establishing the controller
If a cpu unplug event has occured, we need to take the minimum
of the provided nr_io_queues and the number of online cpus,
otherwise we won't be able to connect them as blk-mq mapping
won't dispatch to those queues.
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Jens Axboe [Thu, 30 Mar 2017 19:44:26 +0000 (13:44 -0600)]
null_blk: add blocking mode
This adds a new module parameter to null_blk, blocking. If set, null_blk
will set the BLK_MQ_F_BLOCKING flag, indicating that it sometimes/always
needs to block in its ->queue_rq() function. The intent is to help find
regressions in blocking drivers, since not many of them exist.
If null_blk is loaded with submit_queues > 1 and blocking=1, this
shows the regression recently fixed by bf4907c05e61.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Jens Axboe [Thu, 30 Mar 2017 18:30:39 +0000 (12:30 -0600)]
blk-mq: fix schedule-under-preempt for blocking drivers
Commit a4d907b6a33b unified the single and multi queue request handlers,
but in the process, it also screwed up the locking balance and calls
blk_mq_try_issue_directly() with the ctx preempt lock held. This is a
problem for drivers that have set BLK_MQ_F_BLOCKING, since now they
can't reliably sleep.
While in there, protect against similar issues in the future, by adding
a might_sleep() trigger in the BLOCKING path for direct issue or queue
run.
Reported-by: Josef Bacik <josef@toxicpanda.com> Tested-by: Josef Bacik <josef@toxicpanda.com> Fixes: a4d907b6a33b ("blk-mq: streamline blk_mq_make_request") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Minchan Kim [Thu, 30 Mar 2017 05:20:45 +0000 (14:20 +0900)]
block: do not put mq context in blk_mq_alloc_request_hctx
In blk_mq_alloc_request_hctx, blk_mq_sched_get_request doesn't
get sw context so we don't need to put the context with
blk_mq_put_ctx. Unless, we will see preempt counter underflow.
Jens Axboe [Fri, 24 Mar 2017 18:04:19 +0000 (12:04 -0600)]
blk-mq: include errors in did_work calculation
Currently we return true in blk_mq_dispatch_rq_list() if we queued IO
successfully, but we really want to return whether or not the we made
progress. Progress includes if we got an error return. If we don't,
this can lead to a hang in blk_mq_sched_dispatch_requests() when a
driver is draining IO by returning BLK_MQ_QUEUE_ERROR instead of
manually ending the IO in error and return BLK_MQ_QUEUE_OK.
Tested-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Josef Bacik [Tue, 28 Mar 2017 20:37:52 +0000 (16:37 -0400)]
block-mq: don't re-queue if we get a queue error
When try to issue a request directly and we fail we will requeue the
request, but call blk_mq_end_request() as well. This leads to the
completed request being on a queuelist and getting ended twice, which
causes list corruption in schedulers and other shenanigans.
Signed-off-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_conf_prep() currently calls blkg_lookup_create() while holding
request queue spinlock. This means allocating memory for struct
blkcg_gq has to be made non-blocking. This causes occasional -ENOMEM
failures in call paths like below:
In the code path above, percpu allocator cannot call vmalloc() due to
queue spinlock.
A failure in this call path gives grief to tools which are trying to
configure io weights. We see occasional failures happen shortly after
reboots even when system is not under any memory pressure. Machines
with a lot of cpus are more vulnerable to this condition.
Do struct blkcg_gq allocations outside the queue spinlock to allow
blocking during memory allocations.
Omar Sandoval [Tue, 28 Mar 2017 23:12:17 +0000 (16:12 -0700)]
block: fix leak of q->rq_wb
CONFIG_DEBUG_TEST_DRIVER_REMOVE found a possible leak of q->rq_wb when a
request queue is reregistered. This has been a problem since wbt was
introduced, but the WARN_ON(!list_empty(&stats->callbacks)) in the
blk-stat rework exposed it. Fix it by cleaning up wbt when we unregister
the queue.
Omar Sandoval [Tue, 28 Mar 2017 23:12:15 +0000 (16:12 -0700)]
block: warn if sharing request queue across gendisks
Now that the remaining drivers have been converted to one request queue
per gendisk, let's warn if a request queue gets registered more than
once. This will catch future drivers which might do it inadvertently or
any old drivers that I may have missed.
Ming Lei [Mon, 27 Mar 2017 12:06:58 +0000 (20:06 +0800)]
block: block new I/O just after queue is set as dying
Before commit 780db2071a(blk-mq: decouble blk-mq freezing
from generic bypassing), the dying flag is checked before
entering queue, and Tejun converts the checking into .mq_freeze_depth,
and assumes the counter is increased just after dying flag
is set. Unfortunately we doesn't do that in blk_set_queue_dying().
This patch calls blk_freeze_queue_start() in blk_set_queue_dying(),
so that we can block new I/O coming once the queue is set as dying.
Given blk_set_queue_dying() is always called in remove path
of block device, and queue will be cleaned up later, we don't
need to worry about undoing the counter.
Cc: Tejun Heo <tj@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Mon, 27 Mar 2017 12:06:57 +0000 (20:06 +0800)]
block: rename blk_mq_freeze_queue_start()
As the .q_usage_counter is used by both legacy and
mq path, we need to block new I/O if queue becomes
dead in blk_queue_enter().
So rename it and we can use this function in both
paths.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Mon, 27 Mar 2017 12:06:56 +0000 (20:06 +0800)]
block: add a read barrier in blk_queue_enter()
Without the barrier, reading DEAD flag of .q_usage_counter
and reading .mq_freeze_depth may be reordered, then the
following wait_event_interruptible() may never return.
Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Mon, 27 Mar 2017 12:06:55 +0000 (20:06 +0800)]
blk-mq: comment on races related with timeout handler
This patch adds comment on two races related with
timeout handler:
- requeue from queue busy vs. timeout
- rq free & reallocation vs. timeout
Both the races themselves and current solution aren't
explicit enough, so add comments on them.
Cc: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Wed, 22 Mar 2017 02:14:43 +0000 (10:14 +0800)]
blk-mq: don't complete un-started request in timeout handler
When iterating busy requests in timeout handler,
if the STARTED flag of one request isn't set, that means
the request is being processed in block layer or driver, and
isn't submitted to hardware yet.
In current implementation of blk_mq_check_expired(),
if the request queue becomes dying, un-started requests are
handled as being completed/freed immediately. This way is
wrong, and can cause rq corruption or double allocation[1][2],
when doing I/O and removing&resetting NVMe device at the sametime.
This patch fixes several issues reported by Yi Zhang.
Cc: stable@vger.kernel.org Reported-by: Yi Zhang <yizhan@redhat.com> Tested-by: Yi Zhang <yizhan@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_conf_prep() currently calls blkg_lookup_create() while holding
request queue spinlock. This means allocating memory for struct
blkcg_gq has to be made non-blocking. This causes occasional -ENOMEM
failures in call paths like below:
In the code path above, percpu allocator cannot call vmalloc() due to
queue spinlock.
A failure in this call path gives grief to tools which are trying to
configure io weights. We see occasional failures happen shortly after
reboots even when system is not under any memory pressure. Machines
with a lot of cpus are more vulnerable to this condition.
Update blkg_create() function to temporarily drop the rcu and queue
locks when it is allowed by gfp mask.
Shaohua Li [Mon, 27 Mar 2017 22:19:43 +0000 (15:19 -0700)]
blk-throttle: add latency target support
One hard problem adding .low limit is to detect idle cgroup. If one
cgroup doesn't dispatch enough IO against its low limit, we must have a
mechanism to determine if other cgroups dispatch more IO. We added the
think time detection mechanism before, but it doesn't work for all
workloads. Here we add a latency based approach.
We already have mechanism to calculate latency threshold for each IO
size. For every IO dispatched from a cgorup, we compare its latency
against its threshold and record the info. If most IO latency is below
threshold (in the code I use 75%), the cgroup could be treated idle and
other cgroups can dispatch more IO.
Currently this latency target check is only for SSD as we can't
calcualte the latency target for hard disk. And this is only for cgroup
leaf node so far.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 22:19:42 +0000 (15:19 -0700)]
blk-throttle: add a mechanism to estimate IO latency
User configures latency target, but the latency threshold for each
request size isn't fixed. For a SSD, the IO latency highly depends on
request size. To calculate latency threshold, we sample some data, eg,
average latency for request size 4k, 8k, 16k, 32k .. 1M. The latency
threshold of each request size will be the sample latency (I'll call it
base latency) plus latency target. For example, the base latency for
request size 4k is 80us and user configures latency target 60us. The 4k
latency threshold will be 80 + 60 = 140us.
To sample data, we calculate the order base 2 of rounded up IO sectors.
If the IO size is bigger than 1M, it will be accounted as 1M. Since the
calculation does round up, the base latency will be slightly smaller
than actual value. Also if there isn't any IO dispatched for a specific
IO size, we will use the base latency of smaller IO size for this IO
size.
But we shouldn't sample data at any time. The base latency is supposed
to be latency where disk isn't congested, because we use latency
threshold to schedule IOs between cgroups. If disk is congested, the
latency is higher, using it for scheduling is meaningless. Hence we only
do the sampling when block throttling is in the LOW limit, with
assumption disk isn't congested in such state. If the assumption isn't
true, eg, low limit is too high, calculated latency threshold will be
higher.
Hard disk is completely different. Latency depends on spindle seek
instead of request size. Currently this feature is SSD only, we probably
can use a fixed threshold like 4ms for hard disk though.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 22:19:41 +0000 (15:19 -0700)]
block: track request size in blk_issue_stat
Currently there is no way to know the request size when the request is
finished. Next patch will need this info. We could add extra field to
record the size, but blk_issue_stat has enough space to record it, so
this patch just overloads blk_issue_stat. With this, we will have 49bits
to track time, which still is very long time.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:44 +0000 (10:51 -0700)]
blk-throttle: add interface for per-cgroup target latency
Here we introduce per-cgroup latency target. The target determines how a
cgroup can afford latency increasement. We will use the target latency
to calculate a threshold and use it to schedule IO for cgroups. If a
cgroup's bandwidth is below its low limit but its average latency is
below the threshold, other cgroups can safely dispatch more IO even
their bandwidth is higher than their low limits. On the other hand, if
the first cgroup's latency is higher than the threshold, other cgroups
are throttled to their low limits. So the target latency determines how
we efficiently utilize free disk resource without sacifice of worload's
IO latency.
For example, assume 4k IO average latency is 50us when disk isn't
congested. A cgroup sets the target latency to 30us. Then the cgroup can
accept 50+30=80us IO latency. If the cgroupt's average IO latency is
90us and its bandwidth is below low limit, other cgroups are throttled
to their low limit. If the cgroup's average IO latency is 60us, other
cgroups are allowed to dispatch more IO. When other cgroups dispatch
more IO, the first cgroup's IO latency will increase. If it increases to
81us, we then throttle other cgroups.
User will configure the interface in this way:
echo "8:16 rbps=2097152 wbps=max latency=100 idle=200" > io.low
latency is in microsecond unit
By default, latency target is 0, which means to guarantee IO latency.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:43 +0000 (10:51 -0700)]
blk-throttle: ignore idle cgroup limit
Last patch introduces a way to detect idle cgroup. We use it to make
upgrade/downgrade decision. And the new algorithm can detect completely
idle cgroup too, so we can delete the corresponding code.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:41 +0000 (10:51 -0700)]
blk-throttle: add a simple idle detection
A cgroup gets assigned a low limit, but the cgroup could never dispatch
enough IO to cross the low limit. In such case, the queue state machine
will remain in LIMIT_LOW state and all other cgroups will be throttled
according to low limit. This is unfair for other cgroups. We should
treat the cgroup idle and upgrade the state machine to lower state.
We also have a downgrade logic. If the state machine upgrades because of
cgroup idle (real idle), the state machine will downgrade soon as the
cgroup is below its low limit. This isn't what we want. A more
complicated case is cgroup isn't idle when queue is in LIMIT_LOW. But
when queue gets upgraded to lower state, other cgroups could dispatch
more IO and this cgroup can't dispatch enough IO, so the cgroup is below
its low limit and looks like idle (fake idle). In this case, the queue
should downgrade soon. The key to determine if we should do downgrade is
to detect if cgroup is truely idle.
Unfortunately it's very hard to determine if a cgroup is real idle. This
patch uses the 'think time check' idea from CFQ for the purpose. Please
note, the idea doesn't work for all workloads. For example, a workload
with io depth 8 has disk utilization 100%, hence think time is 0, eg,
not idle. But the workload can run higher bandwidth with io depth 16.
Compared to io depth 16, the io depth 8 workload is idle. We use the
idea to roughly determine if a cgroup is idle.
We treat a cgroup idle if its think time is above a threshold (by
default 1ms for SSD and 100ms for HD). The idea is think time above the
threshold will start to harm performance. HD is much slower so a longer
think time is ok.
The patch (and the latter patches) uses 'unsigned long' to track time.
We convert 'ns' to 'us' with 'ns >> 10'. This is fast but loses
precision, should not a big deal.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:40 +0000 (10:51 -0700)]
blk-throttle: make bandwidth change smooth
When cgroups all reach low limit, cgroups can dispatch more IO. This
could make some cgroups dispatch more IO but others not, and even some
cgroups could dispatch less IO than their low limit. For example, cg1
low limit 10MB/s, cg2 limit 80MB/s, assume disk maximum bandwidth is
120M/s for the workload. Their bps could something like this:
cg1/cg2 bps: T1: 10/80 -> T2: 60/60 -> T3: 10/80
At T1, all cgroups reach low limit, so they can dispatch more IO later.
Then cg1 dispatch more IO and cg2 has no room to dispatch enough IO. At
T2, cg2 only dispatches 60M/s. Since We detect cg2 dispatches less IO
than its low limit 80M/s, we downgrade the queue from LIMIT_MAX to
LIMIT_LOW, then all cgroups are throttled to their low limit (T3). cg2
will have bandwidth below its low limit at most time.
The big problem here is we don't know the maximum bandwidth of the
workload, so we can't make smart decision to avoid the situation. This
patch makes cgroup bandwidth change smooth. After disk upgrades from
LIMIT_LOW to LIMIT_MAX, we don't allow cgroups use all bandwidth upto
their max limit immediately. Their bandwidth limit will be increased
gradually to avoid above situation. So above example will became
something like:
In this way cgroups bandwidth will be above their limit in majority
time, this still doesn't fully utilize disk bandwidth, but that's
something we pay for sharing.
Scale up is linear. The limit scales up 1/2 .low limit every
throtl_slice after upgrade. The scale up will stop if the adjusted limit
hits .max limit. Scale down is exponential. We cut the scale value half
if a cgroup doesn't hit its .low limit. If the scale becomes 0, we then
fully downgrade the queue to LIMIT_LOW state.
Note this doesn't completely avoid cgroup running under its low limit.
The best way to guarantee cgroup doesn't run under its limit is to set
max limit. For example, if we set cg1 max limit to 40, cg2 will never
run under its low limit.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:39 +0000 (10:51 -0700)]
blk-throttle: detect completed idle cgroup
cgroup could be assigned a limit, but doesn't dispatch enough IO, eg the
cgroup is idle. When this happens, the cgroup doesn't hit its limit, so
we can't move the state machine to higher level and all cgroups will be
throttled to their lower limit, so we waste bandwidth. Detecting idle
cgroup is hard. This patch handles a simple case, a cgroup doesn't
dispatch any IO. We ignore such cgroup's limit, so other cgroups can use
the bandwidth.
Please note this will be replaced with a more sophisticated algorithm
later, but this demonstrates the idea how we handle idle cgroups, so I
leave it here.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:38 +0000 (10:51 -0700)]
blk-throttle: choose a small throtl_slice for SSD
The throtl_slice is 100ms by default. This is a long time for SSD, a lot
of IO can run. To make cgroups have smoother throughput, we choose a
small value (20ms) for SSD.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:37 +0000 (10:51 -0700)]
blk-throttle: make throtl_slice tunable
throtl_slice is important for blk-throttling. It's called slice
internally but it really is a time window blk-throttling samples data.
blk-throttling will make decision based on the samplings. An example is
bandwidth measurement. A cgroup's bandwidth is measured in the time
interval of throtl_slice.
A small throtl_slice meanse cgroups have smoother throughput but burn
more CPUs. It has 100ms default value, which is not appropriate for all
disks. A fast SSD can dispatch a lot of IOs in 100ms. This patch makes
it tunable.
Since throtl_slice isn't a time slice, the sysfs name
'throttle_sample_time' reflects its character better.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:36 +0000 (10:51 -0700)]
blk-throttle: make sure expire time isn't too big
cgroup could be throttled to a limit but when all cgroups cross high
limit, queue enters a higher state and so the group should be throttled
to a higher limit. It's possible the cgroup is sleeping because of
throttle and other cgroups don't dispatch IO any more. In this case,
nobody can trigger current downgrade/upgrade logic. To fix this issue,
we could either set up a timer to wakeup the cgroup if other cgroups are
idle or make sure this cgroup doesn't sleep too long. Setting up a timer
means we must change the timer very frequently. This patch chooses the
latter. Making cgroup sleep time not too big wouldn't change cgroup
bps/iops, but could make it wakeup more frequently, which isn't a big
issue because throtl_slice * 8 is already quite big.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:35 +0000 (10:51 -0700)]
blk-throttle: add downgrade logic
When queue state machine is in LIMIT_MAX state, but a cgroup is below
its low limit for some time, the queue should be downgraded to lower
state as one cgroup's low limit isn't met.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:34 +0000 (10:51 -0700)]
blk-throttle: add upgrade logic for LIMIT_LOW state
When queue is in LIMIT_LOW state and all cgroups with low limit cross
the bps/iops limitation, we will upgrade queue's state to
LIMIT_MAX. To determine if a cgroup exceeds its limitation, we check if
the cgroup has pending request. Since cgroup is throttled according to
the limit, pending request means the cgroup reaches the limit.
If a cgroup has limit set for both read and write, we consider the
combination of them for upgrade. The reason is read IO and write IO can
interfere with each other. If we do the upgrade based in one direction
IO, the other direction IO could be severly harmed.
For a cgroup hierarchy, there are two cases. Children has lower low
limit than parent. Parent's low limit is meaningless. If children's
bps/iops cross low limit, we can upgrade queue state. The other case is
children has higher low limit than parent. Children's low limit is
meaningless. As long as parent's bps/iops (which is a sum of childrens
bps/iops) cross low limit, we can upgrade queue state.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:33 +0000 (10:51 -0700)]
blk-throttle: configure bps/iops limit for cgroup in low limit
each queue will have a state machine. Initially queue is in LIMIT_LOW
state, which means all cgroups will be throttled according to their low
limit. After all cgroups with low limit cross the limit, the queue state
gets upgraded to LIMIT_MAX state.
For max limit, cgroup will use the limit configured by user.
For low limit, cgroup will use the minimal value between low limit and
max limit configured by user. If the minimal value is 0, which means the
cgroup doesn't configure low limit, we will use max limit to throttle
the cgroup and the cgroup is ready to upgrade to LIMIT_MAX
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaohua Li [Mon, 27 Mar 2017 17:51:32 +0000 (10:51 -0700)]
blk-throttle: add .low interface
Add low limit for cgroup and corresponding cgroup interface. To be
consistent with memcg, we allow users configure .low limit higher than
.max limit. But the internal logic always assumes .low limit is lower
than .max limit. So we add extra bps/iops_conf fields in throtl_grp for
userspace configuration. Old bps/iops fields in throtl_grp will be the
actual limit we use for throttling.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Dan Carpenter [Thu, 23 Mar 2017 10:24:55 +0000 (13:24 +0300)]
block: make nr_iovecs unsigned in bio_alloc_bioset()
There isn't a bug here, but Smatch is not smart enough to know that
"nr_iovecs" can't be negative so it complains about underflows.
Really, it's slightly cleaner to make this parameter unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Turn the different ways of merging or issuing I/O into a series of if/else
statements instead of the current maze of gotos. Note that this means we
pin the CPU a little longer for some cases as the CTX put is moved to
common code at the end of the function.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Rename blk_mq_try_issue_directly to __blk_mq_try_issue_directly and add a
new wrapper that takes care of RCU / SRCU locking to avoid having
boileplate code in the caller which would get duplicated with new callers.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Jens Axboe <axboe@fb.com>
As you can see RAX value is already poisoned showing that gendisk we got
is already freed. The problem is that get_gendisk() looks up device
number in ext_devt_idr and then does get_disk() which does kobject_get()
on the disks kobject. However the disk gets removed from ext_devt_idr
only in disk_release() (through blk_free_devt()) at which moment it has
already 0 refcount and is already on its way to be freed. Indeed we've
got a warning from kobject_get() about 0 refcount shortly before the
oops.
We fix the problem by using kobject_get_unless_zero() in get_disk() so
that get_disk() cannot get reference on a disk that is already being
freed.
Tested-by: Lekshmi Pillai <lekshmicpillai@in.ibm.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:37:00 +0000 (01:37 +0100)]
block: Fix oops in locked_inode_to_wb_and_lock_list()
When block device is closed, we call inode_detach_wb() in __blkdev_put()
which sets inode->i_wb to NULL. That is contrary to expectations that
inode->i_wb stays valid once set during the whole inode's lifetime and
leads to oops in wb_get() in locked_inode_to_wb_and_lock_list() because
inode_to_wb() returned NULL.
The reason why we called inode_detach_wb() is not valid anymore though.
BDI is guaranteed to stay along until we call bdi_put() from
bdev_evict_inode() so we can postpone calling inode_detach_wb() to that
moment.
Also add a warning to catch if someone uses inode_detach_wb() in a
dangerous way.
Reported-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:59 +0000 (01:36 +0100)]
bdi: Rename cgwb_bdi_destroy() to cgwb_bdi_unregister()
Rename cgwb_bdi_destroy() to cgwb_bdi_unregister() as it gets called
from bdi_unregister() which is not necessarily called from bdi_destroy()
and thus the name is somewhat misleading.
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:58 +0000 (01:36 +0100)]
bdi: Do not wait for cgwbs release in bdi_unregister()
Currently we wait for all cgwbs to get released in cgwb_bdi_destroy()
(called from bdi_unregister()). That is however unnecessary now when
cgwb->bdi is a proper refcounted reference (thus bdi cannot get
released before all cgwbs are released) and when cgwb_bdi_destroy()
shuts down writeback directly.
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:57 +0000 (01:36 +0100)]
bdi: Shutdown writeback on all cgwbs in cgwb_bdi_destroy()
Currently we waited for all cgwbs to get freed in cgwb_bdi_destroy()
which also means that writeback has been shutdown on them. Since this
wait is going away, directly shutdown writeback on cgwbs from
cgwb_bdi_destroy() to avoid live writeback structures after
bdi_unregister() has finished. To make that safe with concurrent
shutdown from cgwb_release_workfn(), we also have to make sure
wb_shutdown() returns only after the bdi_writeback structure is really
shutdown.
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:56 +0000 (01:36 +0100)]
bdi: Unify bdi->wb_list handling for root wb_writeback
Currently root wb_writeback structure is added to bdi->wb_list in
bdi_init() and never removed. That is different from all other
wb_writeback structures which get added to the list when created and
removed from it before wb_shutdown().
So move list addition of root bdi_writeback to bdi_register() and list
removal of all wb_writeback structures to wb_shutdown(). That way a
wb_writeback structure is on bdi->wb_list if and only if it can handle
writeback and it will make it easier for us to handle shutdown of all
wb_writeback structures in bdi_unregister().
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:55 +0000 (01:36 +0100)]
bdi: Make wb->bdi a proper reference
Make wb->bdi a proper refcounted reference to bdi for all bdi_writeback
structures except for the one embedded inside struct backing_dev_info.
That will allow us to simplify bdi unregistration.
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:54 +0000 (01:36 +0100)]
bdi: Mark congested->bdi as internal
congested->bdi pointer is used only to be able to remove congested
structure from bdi->cgwb_congested_tree on structure release. Moreover
the pointer can become NULL when we unregister the bdi. Rename the field
to __bdi and add a comment to make it more explicit this is internal
stuff of memcg writeback code and people should not use the field as
such use will be likely race prone.
We do not bother with converting congested->bdi to a proper refcounted
reference. It will be slightly ugly to special-case bdi->wb.congested to
avoid effectively a cyclic reference of bdi to itself and the reference
gets cleared from bdi_unregister() making it impossible to reference
a freed bdi.
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Thu, 23 Mar 2017 00:36:53 +0000 (01:36 +0100)]
block: Fix bdi assignment to bdev inode when racing with disk delete
When disk->fops->open() in __blkdev_get() returns -ERESTARTSYS, we
restart the process of opening the block device. However we forget to
switch bdev->bd_bdi back to noop_backing_dev_info and as a result bdev
inode will be pointing to a stale bdi. Fix the problem by setting
bdev->bd_bdi later when __blkdev_get() is already guaranteed to succeed.
Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
Jens Axboe [Tue, 21 Mar 2017 23:20:01 +0000 (17:20 -0600)]
block: fix stacked driver stats init and free
If a driver allocates a queue for stacked usage, then it does
not currently get stats allocated. This causes the later init
of, eg, writeback throttling to blow up. Move the init to the
queue allocation instead.
Additionally, allow a NULL callback unregistration. This avoids
having the caller check for that, fixing another oops on
removal of a block device that doesn't have poll stats allocated.
Omar Sandoval [Tue, 21 Mar 2017 15:56:08 +0000 (08:56 -0700)]
blk-stat: convert to callback-based statistics reporting
Currently, statistics are gathered in ~0.13s windows, and users grab the
statistics whenever they need them. This is not ideal for both in-tree
users:
1. Writeback throttling wants its own dynamically sized window of
statistics. Since the blk-stats statistics are reset after every
window and the wbt windows don't line up with the blk-stats windows,
wbt doesn't see every I/O.
2. Polling currently grabs the statistics on every I/O. Again, depending
on how the window lines up, we may miss some I/Os. It's also
unnecessary overhead to get the statistics on every I/O; the hybrid
polling heuristic would be just as happy with the statistics from the
previous full window.
This reworks the blk-stats infrastructure to be callback-based: users
register a callback that they want called at a given time with all of
the statistics from the window during which the callback was active.
Users can dynamically bucketize the statistics. wbt and polling both
currently use read vs. write, but polling can be extended to further
subdivide based on request size.
The callbacks are kept on an RCU list, and each callback has percpu
stats buffers. There will only be a few users, so the overhead on the
I/O completion side is low. The stats flushing is also simplified
considerably: since the timer function is responsible for clearing the
statistics, we don't have to worry about stale statistics.
wbt is a trivial conversion. After the conversion, the windowing problem
mentioned above is fixed.
For polling, we register an extra callback that caches the previous
window's statistics in the struct request_queue for the hybrid polling
heuristic to use.
Since we no longer have a single stats buffer for the request queue,
this also removes the sysfs and debugfs stats entries. To replace those,
we add a debugfs entry for the poll statistics.
projects / karo-tx-linux.git / log