Gavin Shan [Thu, 8 Oct 2015 03:58:53 +0000 (14:58 +1100)]
powerpc/eeh: More relaxed hotplug criterion
Currently, we rely on the existence of struct pci_driver::err_handler
to decide if the corresponding PCI device should be unplugged during
EEH recovery (partially hotplug case). However that check is not
sufficient. Some device drivers implement only some of the EEH error
handlers to collect diag-data. That means the driver still expects a
hotplug to recover from the EEH error.
This makes the hotplug criterion more relaxed: if the device driver
doesn't provide all necessary EEH error handlers, it will experience
hotplug during EEH recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
[mpe: Minor change log rewording] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 8 Oct 2015 03:58:52 +0000 (14:58 +1100)]
powerpc/eeh: Don't unfreeze PHB PE after reset
On PowerNV platform, the PE is kept in frozen state until the PE
reset is completed to avoid recursive EEH error caused by MMIO
access during the period of EEH reset. The PE's frozen state is
cleared after BARs of PCI device included in the PE are restored
and enabled. However, we needn't clear the frozen state for PHB PE
explicitly at this point as there is no real PE for PHB PE. As the
PHB PE is always binding with PE#0, we actually clear PE#0, which
is wrong. It doesn't incur any problem though.
This checks if the PE is PHB PE and doesn't clear the frozen state
if it is.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/prom: Avoid reference to potentially freed memory
of_get_property() is used inside the loop, but then the reference to the
node is dropped before dereferencing the prop pointer, which could by then
point to junk if the node has been freed.
Instead use of_property_read_u32() to actually read the property
value before dropping the reference.
of_property_read_u32() requires at least one cell (u32) to be present,
which is stricter than the old logic which would happily dereference a
property of any size. However we believe all device trees in the wild
have at least one cell.
Skiboot may produce memory nodes with more than one cell, but that is
OK, of_property_read_u32() will return the first one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[mpe: Expand change log with device tree details] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Tue, 13 Oct 2015 08:17:07 +0000 (19:17 +1100)]
powerpc/cell: Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU
The TUNE_CELL option allows you to build a kernel that runs on multiple
CPUs but is tuned (ie. optimised) to run on Cell CPUs. Now days no one
is building a distro in that fashion, and any users who are building
custom kernels for their Cell machines are better off building with
CONFIG_CELL_CPU, which builds a kernel that only runs on Cell and
therefore can be optimised even more aggresively.
Dropping the option also avoids confusing other users, who are presented
with an option to tune for Cell when they are not building for a Cell
CPU at all.
Suggested-by: Thomas Huth <thuth@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Wed, 14 Oct 2015 05:58:36 +0000 (16:58 +1100)]
powerpc/xmon: Add some more elements to the existing PACA dump list
This patch adds a set of new elements to the existing PACA dump list
inside an xmon session which can be listed below improving the overall
xmon debug support.
With this patch, a typical xmon PACA dump looks something like this.
Sam bobroff [Thu, 8 Oct 2015 00:50:23 +0000 (11:50 +1100)]
powerpc/xmon: Paged output for paca display
The paca display is already more than 24 lines, which can be problematic
if you have an old school 80x24 terminal, or more likely you are on a
virtual terminal which does not scroll for whatever reason.
This patch adds a new command "#", which takes a single (hex) numeric
argument: lines per page. It will cause the output of "dp" and "dpa"
to be broken into pages, if necessary.
Paul Gortmaker [Tue, 13 Oct 2015 23:20:51 +0000 (19:20 -0400)]
powerpc: Delete old orphaned PrPMC 280/2800 DTS and boot file.
In commit 3c8464a9b12bf83807b6e2c896d7e7b633e1cae7 ("powerpc:
Delete old PrPMC 280/2800 support") we got rid of most of the C
code, and the Makefile/Kconfig hooks, but it seems I left the
platform's DTS file orphaned in the tree as well as the boot code.
Here we get rid of them both.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
.exit.text is discarded at run time and there are some references from
that to .exit.data, so we need to discard .exit.data at run time as well.
Fixes these errors:
`.exit.data' referenced in section `.exit.text' of drivers/built-in.o: defined in discarded section `.exit.data' of drivers/built-in.o
`.exit.data' referenced in section `.exit.text' of drivers/built-in.o: defined in discarded section `.exit.data' of drivers/built-in.o
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrew Donnellan [Tue, 13 Oct 2015 04:09:44 +0000 (15:09 +1100)]
cxl: Free virtual PHB when removing
When adding a vPHB in cxl_pci_vphb_add(), we allocate a pci_controller
struct using pcibios_alloc_controller(). However, we don't free it in
cxl_pci_vphb_remove(), causing a leak.
Call pcibios_free_controller() in cxl_pci_vphb_remove() to free the vPHB
data structure correctly.
Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sam bobroff [Tue, 13 Oct 2015 01:49:28 +0000 (12:49 +1100)]
powerpc: Individual System V IPC system calls
This patch provides individual system call numbers for the following
System V IPC system calls, on PowerPC, so that they do not need to be
multiplexed:
* semop, semget, semctl, semtimedop
* msgsnd, msgrcv, msgget, msgctl
* shmat, shmdt, shmget, shmctl
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Drop always true CONFIG_PSERIES_MSI
Now that pseries selects PCI_MSI && PCI, EEH will always be true, and
therefore CONFIG_PSERIES_MSI will always be true. So drop it, and move
msi.o to obj-y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pseries build with PCI=n looks to have been broken for at least 5
years, and no one's noticed or cared.
Following the obvious breakages backward, the first commit I can find
that builds is the parent of 2eb4afb69ff3 ("powerpc/pci: Move pseries
code into pseries platform specific area") from April 2009.
A distro would never ship a PCI=n kernel, so it is only useful for folks
building custom kernels. Also on KVM the virtio devices appear on PCI,
so it would only be useful if you were building kernels specifically to
run on PowerVM and with no PCI devices.
The added code complexity, and testing load (which we've clearly not
been doing), is not justified by the small reduction in kernel size for
such a niche use case.
So just make PCI non-optional on pseries.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 15 Oct 2015 03:33:57 +0000 (14:33 +1100)]
scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O=
My recent commit d2036f30cfe1 ("scripts/kconfig/Makefile: Allow
KBUILD_DEFCONFIG to be a target"), contained a bug in that when it
checks if KBUILD_DEFCONFIG is a file it forgets to prepend $(srctree) to
the path.
This causes the build to fail when building out of tree (with O=), and
when the value of KBUILD_DEFCONFIG is 'defconfig'. In that case we will
fail to find the 'defconfig' file, because we look in the build
directory not $(srctree), and so we will call Make again with
'defconfig' as the target. From there we loop infinitely calling 'make
defconfig' again and again.
The fix is simple, we need to look for the file under $(srctree).
Fixes: d2036f30cfe1 ("scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target") Reported-by: Olof Johansson <olof@lixom.net> Acked-by: Michal Marek <mmarek@suse.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Differentiate between hugetlb and THP during page walk
We need to properly identify whether a hugepage is an explicit or
a transparent hugepage in follow_huge_addr(). We used to depend
on hugepage shift argument to do that. But in some case that can
result in wrong results. For ex:
On finding a transparent hugepage we set hugepage shift to PMD_SHIFT.
But we can end up clearing the thp pte, via pmdp_huge_get_and_clear.
We do prevent reusing the pfn page via the usage of
kick_all_cpus_sync(). But that happens after we updated the pte to 0.
Hence in follow_huge_addr() we can find hugepage shift set, but transparent
huge page check fail for a thp pte.
NOTE: We fixed a variant of this race against thp split in commit 691e95fd7396905a38d98919e9c150dbc3ea21a3
("powerpc/mm/thp: Make page table walk safe against thp split/collapse")
Without this patch, we may hit the BUG_ON(flags & FOLL_GET) in
follow_page_mask occasionally.
In the long term, we may want to switch ppc64 64k page size config to
enable CONFIG_ARCH_WANT_GENERAL_HUGETLB
Reported-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After commit e2b3d202d1dba8f3546ed28224ce485bc50010be
("powerpc: Switch 16GB and 16MB explicit hugepages to a
different page table format"), we don't need to support
is_hugepd() for 64K page size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andy Shevchenko [Thu, 1 Oct 2015 09:46:10 +0000 (12:46 +0300)]
powerpc/pseries: re-use code from of_helpers module
The derive_parent() has similar semantics to what we have in newly introduced
of_helpers module. The replacement reduces code base and propagates the actual
error code to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andy Shevchenko [Thu, 1 Oct 2015 09:46:09 +0000 (12:46 +0300)]
powerpc/pseries: handle nodes without '/'
In case we have node without '/' strrchr() returns NULL which might lead to
crash. Replace strrchr() by kbasename() and modify condition to avoid such
behaviour.
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Wed, 23 Sep 2015 05:40:34 +0000 (15:40 +1000)]
scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target
Arch Makefiles can set KBUILD_DEFCONFIG to tell kbuild the name of the
defconfig that should be built by default.
However currently there is an assumption that KBUILD_DEFCONFIG points to
a file at arch/$(SRCARCH)/configs/$(KBUILD_DEFCONFIG).
We would like to use a target, using merge_config, as our defconfig, so
adapt the logic in scripts/kconfig/Makefile to allow that.
To minimise the chance of breaking anything, we first check if
KBUILD_DEFCONFIG is a file, and if so we do the old logic. If it's not a
file, then we call the top-level Makefile with KBUILD_DEFCONFIG as the
target.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Michal Marek <mmarek@suse.com>
Michael Neuling [Fri, 25 Sep 2015 04:01:40 +0000 (14:01 +1000)]
powerpc/vdso: Avoid link stack corruption in __get_datapage()
powerpc has a link register (lr) used for calling functions. We "bl
<func>" to call a function, and "blr" to return back to the call site.
The lr is only a single register, so if we call another function from
inside this function (ie. nested calls), software must save away the
lr on the software stack before calling the new function. Before
returning (ie. before the "blr"), the lr is restored by software from
the software stack.
This makes branch prediction quite difficult for the processor as it
will only know the branch target just before the "blr".
To help with this, modern powerpc processors keep a (non-architected)
hardware stack of lr called a "link stack". When a "bl <func>" is
run, the lr is pushed onto this stack. When a "blr" is called, the
branch predictor pops the lr value from the top of the link stack, and
uses it to predict the branch target. Hence the processor pipeline
knows a lot earlier the branch target.
This works great but there are some cases where you call "bl" but
without a matching "blr". Once such case is when trying to determine
the program counter (which can't be read directly). Here you "bl+4;
mflr" to get the program counter. If you do this, the link stack will
get out of sync with reality, causing the branch predictor to
mis-predict subsequent function returns.
To avoid this, modern micro-architectures have a special case of bl.
Using the form "bcl 20,31,+4", ensures the processor doesn't push to
the link stack.
The 32 and 64 bit variants of __get_datapage() use a "bl; mflr" to
determine the loaded address of the VDSO. The current versions of
these attempt to use this special bl variant.
Unfortunately they use +8 rather than the required +4. Hence the
current code results in the link stack getting out of sync with
reality and hence the resulting performance degradation.
This patch moves it to bcl+4 by moving __kernel_datapage_offset out of
__get_datapage().
With this patch, running a gettimeofday() (which uses
__get_datapage()) microbenchmark we get a decent bump in performance
on POWER7/8.
For the benchmark in tools/testing/selftests/powerpc/benchmarks/gettimeofday.c
POWER8:
64bit gets ~4% improvement
32bit gets ~9% improvement
POWER7:
64bit gets ~7% improvement
Signed-off-by: Michael Neuling <mikey@neuling.org> Reported-by: Aaron Sawdey <sawdey@us.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Fri, 25 Sep 2015 04:01:39 +0000 (14:01 +1000)]
powerpc/selftest: Add gettimeofday() benchmark
This adds a benchmark directory to the powerpc selftests and adds a
gettimeofday() benchmark to it.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some dynamic loaders may be slightly faster if a GNU hash is
available.
This is unlikely to have any measurable effect on the time it takes
to resolve vdso symbols (since there are so few of them). In some
contexts, it can be a win for a different reason: if every DSO has a
GNU hash section, then libc can avoid calculating SysV hashes at
all. Both musl and glibc appear to have this optimization.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Colin King [Mon, 14 Sep 2015 19:35:04 +0000 (19:35 +0000)]
drivers/ps3: Fix ps3-vuart null dereference
On the unlikely event that drv is null, the current code will
perform a null pointer dereference with it when printing a dev_dbg
message. Instead, the BUG_ON check on drv should be performed
before we emit the dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Geoff Levand <geoff@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc: Kconfig: remove BE-only platforms from LE kernel build
Currently, little endian is only supported on powernv and pseries,
however, Kconfigs still allow us to include other platforms in a LE
kernel, this may result in space wasting or even build error if some
BE-only platforms always assume they are built for a BE kernel. So just
modify the Kconfigs of BE-only platforms to remove them from being built
for a LE kernel.
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two bugfixes from Andy addressing at least some of the subtle NMI
related wreckage which has been reported by Sasha Levin"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
x86/paravirt: Replace the paravirt nop with a bona fide empty function
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first real batch of fixes this release cycle. Nothing really
concerning, and diffstat is a bit inflated due to some DT contents
moving around on STi platforms.
There's a collection of them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in
QCOM SCM firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge
window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting
to see a few more users in the wild"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
ARM: dts: fix omap2+ address translation for pbias
firmware: qcom: scm: Add function stubs for ARM64
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
ARM: pxa: balloon3: Fix build error
ARM: dts: Fixup model name for HP t410 dts
ARM: dts: DRA7: fix a typo in ethernet
ARM: omap2plus_defconfig: make PCF857x built-in
ARM: dts: Use ti,pbias compatible string for pbias
ARM: OMAP5: Cleanup options for SoC only build
ARM: DRA7: Select missing options for SoC only build
ARM: OMAP2+: board-generic: Remove stale of_irq macros
ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
ARM: dts: am335x-phycore-som: Fix mpu voltage
...
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Four fixes from testing at the recent SMB3 Plugfest including two
important authentication ones (one fixes authentication problems to
some popular servers when clock times differ more than two hours
between systems, the other fixes Kerberos authentication for SMB3)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
fix encryption error checks on mount
[SMB3] Fix sec=krb5 on smb3 mounts
cifs: use server timestamp for ntlmv2 authentication
disabling oplocks/leases via module parm enable_oplocks broken for SMB3
Olof Johansson [Sun, 27 Sep 2015 05:22:31 +0000 (22:22 -0700)]
Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.3-rc cycle:
- Two more patches to fix most of the MMC regressions with the
PBIAS regulator changes. At least two MMC driver related issues
still seems to remain for omap3 legacy booting and omap4 duovero.
Note that the dts changes depend on a recent regulator fix, and
are based on the regulator commit now in mainline kernel
- Enable autoidle for am43xx clocks to prevent clocks from staying
always on
- Fix i2c5 pinctrl offsets for omap5-uevm
- Enable PCA953X as that's needed for HDMI to work on omap5
- Update phy supplies for beagle x15 beta board
- Use palmas-usb for on beagle x15 to start using the related
driver that recently got merged
* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: fix omap2+ address translation for pbias
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
regulator: pbias: program pbias register offset in pbias driver
ARM: omap2plus_defconfig: Enable MUSB DMA support
ARM: DRA752: Add ID detect for ES2.0
ARM: OMAP3: vc: fix 'or' always true warning
ARM: OMAP2+: Fix booting if no timer parent clock is available
ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Pull SCSI target fixes from Nicholas Bellinger:
"This includes a iser-target series from Jenny + Sagi @ Mellanox that
addresses the few remaining active I/O shutdown bugs, along with a
patch to support zero-copy for immediate data payloads that gives a
nice performance improvement for small block WRITEs.
Also included are some recent >= v4.2 regression bug-fixes. The most
notable is a RCU conversion regression for SPC-3 PR registrations, and
recent removal of obsolete RFC-3720 markers that introduced a login
regression bug with MSFT iSCSI initiators.
Thanks to everyone who has been testing + reporting bugs for v4.x"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Avoid OFMarker + IFMarker negotiation
target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
target: Fix target_sense_desc_format NULL pointer dereference
target: Propigate backend read-only to core_tpg_add_lun
target: Fix PR registration + APTPL RCU conversion regression
iser-target: Skip data copy if all the command data comes as immediate
iser-target: Change the recv buffers posting logic
iser-target: Fix pending connections handling in target stack shutdown sequnce
iser-target: Remove np_ prefix from isert_np members
iser-target: Remove unused variables
iser-target: Put the reference on commands waiting for unsol data
iser-target: remove command with state ISTATE_REMOVE
Merge tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver fixes for 4.3-rc3.
There's the usual assortment of new device ids, combined with xhci and
gadget driver fixes. Full details in the shortlog. All of these have
been in linux-next with no reported problems"
* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
MAINTAINERS: remove amd5536udc USB gadget driver maintainer
USB: whiteheat: fix potential null-deref at probe
xhci: init command timeout timer earlier to avoid deleting it uninitialized
xhci: change xhci 1.0 only restrictions to support xhci 1.1
usb: xhci: exit early in xhci_setup_device() if we're halted or dying
usb: xhci: stop everything on the first call to xhci_stop
usb: xhci: Clear XHCI_STATE_DYING on start
usb: xhci: lock mutex on xhci_stop
xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
xhci: give command abortion one more chance before killing xhci
usb: Use the USB_SS_MULT() macro to get the burst multiplier.
usb: dwc3: gadget: Fix BUG in RT config
usb: musb: fix cppi channel teardown for isoch transfer
usb: phy: isp1301: Export I2C module alias information
usb: gadget: drop null test before destroy functions
usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
usb: gadget: dummy_hcd: fix rescan logic for transfer
usb: gadget: dummy_hcd: fix unneeded else-if condition
usb: gadget: dummy_hcd: emulate sending zlp in packet logic
usb: musb: dsps: fix polling in device-only mode
...
Merge tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"Here is one serial driver fix for 4.3-rc3 that resolves a module
loading issue due to splitting up of the 8250 driver into smaller
pieces. It's been in linux-next with no reported problems"
* tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: Add missing module license for 8250_base.ko
Merge tag 'char-misc-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here's some tiny char and misc driver fixes that resolve some reported
errors for 4.3-rc3.
All of these have been in linux-next with no problems for a while"
* tag 'char-misc-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
extcon: Fix attached value returned by is_extcon_changed
Drivers: hv: vmbus: fix init_vp_index() for reloading hv_netvsc
mei: fix debugfs files leak on error path
thunderbolt: Allow loading of module on recent Apple MacBooks with thunderbolt 2 controller
1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
instead of cloning them. From Daniel Borkmann.
2) When converting classical BPF into eBPF, fix the setting of the
source reg to BPF_REG_X. From Tycho Andersen.
3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
Linus Lussing.
4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.
5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
Roopa Prabhu.
6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.
7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
Florian Westphal.
8) Check DMA mapping errors in bna driver, from Ivan Vecera.
9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
misclearing of interrupt status in TX timeout handler, etc.) from
David Woodhouse.
10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
Hugne.
11) Fix autobind races et al. in netlink code, from Herbert Xu with
help from Tejun Heo and others.
12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.
13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
Eric Dumazet.
14) Fix array overruns in mac80211, from Johannes Berg and Dan
Carpenter.
15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.
16) Fix race between poll_one_napi and napi_disable, from Neil Horman.
17) Fix byte order in geneve tunnel port config, from John W Linville.
18) Fix handling of ARP replies over lightweight tunnels, from Jiri
Benc.
19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
Kok and Roopa Prabhu.
20) Several reference count handling bug fixes in the PHY/MDIO layer
from Russel King.
21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.
22) Fix crash in icmp_route_lookup(), from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: Fix panic in icmp_route_lookup
net: update docbook comment for __mdiobus_register()
ppp: fix lockdep splat in ppp_dev_uninit()
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
phy: marvell: add link partner advertised modes
net: fix net_device refcounting
phy: add phy_device_remove()
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
net: fix phy refcounting in a bunch of drivers
of_mdio: fix MDIO phy device refcounting
phy: add proper phy struct device refcounting
phy: fix mdiobus module safety
net: dsa: fix of_mdio_find_bus() device refcount leak
phy: fix of_mdio_find_bus() device refcount leak
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
ip6_gre: Reduce log level in ip6gre_err() to debug
fib_rules: fix fib rule dumps across multiple skbs
bnx2x: byte swap rss_key to comply to Toeplitz specs
net: revert "net_sched: move tp->root allocation into fw_init()"
lwtunnel: remove source and destination UDP port config option
...
Prior to the VRF change the oif was not set in the flow struct, so the
VRF support should really have only added the vrf_master_ifindex lookup.
Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX") Cc: Andrey Melnikov <temnota.am@gmail.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MAINTAINERS: remove amd5536udc USB gadget driver maintainer
Thomas can no longer work on the driver, so he asked me to mark the
MAINTAINER entry as "Orphan" with the hope that someone else would
someday pick it up.
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge branch 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull another cgroup fix from Tejun Heo:
"The cgroup writeback support got inadvertently enabled for traditional
hierarchies revealing two regressions which are currently being worked
on. It shouldn't have been enabled on traditional hierarchies, so
disable it on them. This is enough to make the regressions go away
for people who aren't experimenting with cgroup"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup, writeback: don't enable cgroup writeback on traditional hierarchies
ppp_dev_uninit() locks all_ppp_mutex while under rtnl mutex protection.
ppp_create_interface() must then lock these mutexes in that same order
to avoid possible deadlock.
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
The builds of allmodconfig of avr32 is failing with:
drivers/net/ethernet/via/via-rhine.c:1098:2: error: implicit declaration
of function 'pci_iomap' [-Werror=implicit-function-declaration]
drivers/net/ethernet/via/via-rhine.c:1119:2: error: implicit declaration
of function 'pci_iounmap' [-Werror=implicit-function-declaration]
The generic empty pci_iomap and pci_iounmap is used only if CONFIG_PCI
is not defined and CONFIG_GENERIC_PCI_IOMAP is defined.
Add GENERIC_PCI_IOMAP in the dependency list for VIA_RHINE as we are
getting build failure when CONFIG_PCI and CONFIG_GENERIC_PCI_IOMAP both
are not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 23 Sep 2015 23:07:17 +0000 (00:07 +0100)]
phy: marvell: add link partner advertised modes
Read the standard link partner advertisment registers and store it in
phydev->lp_advertising, so ethtool can report this information to
userspace via ethtool. Zero it as per genphy if autonegotiation is
disabled. Tested with a Marvell 88E1512 PHY.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is an assorted set I've been queuing up:
Jeff Mahoney tracked down a tricky one where we ended up starting IO
on the wrong mapping for special files in btrfs_evict_inode. A few
people reported this one on the list.
Filipe found (and provided a test for) a difficult bug in reading
compressed extents, and Josef fixed up some quota record keeping with
snapshot deletion. Chandan killed off an accounting bug during DIO
that lead to WARN_ONs as we freed inodes"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: keep dropped roots in cache until transaction commit
Btrfs: Direct I/O: Fix space accounting
btrfs: skip waiting on ordered range for special files
Btrfs: fix read corruption of compressed and shared extents
Btrfs: remove unnecessary locking of cleaner_mutex to avoid deadlock
Btrfs: don't initialize a space info as full to prevent ENOSPC
Merge tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- fix v4.2 SEEK on files over 2 gigs
- Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
- Fix recovery of recalled read delegations
Bugfixes:
- Fix a case where NFSv4 fails to send CLOSE after a server reboot
- Fix sunrpc to wait for connections to complete before retrying
- Fix sunrpc races between transport connect/disconnect and shutdown
- Fix an infinite loop when layoutget fail with BAD_STATEID
- nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
- Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
- Fix layoutreturn/close ordering issues"
* tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS41: make close wait for layoutreturn
NFS: Skip checking ds_cinfo.buckets when lseg's commit_through_mds is set
NFSv4.x/pnfs: Don't try to recover stateids twice in layoutget
NFSv4: Recovery of recalled read delegations is broken
NFS: Fix an infinite loop when layoutget fail with BAD_STATEID
NFS: Do cleanup before resetting pageio read/write to mds
SUNRPC: xs_sock_mark_closed() does not need to trigger socket autoclose
SUNRPC: Lock the transport layer on shutdown
nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
SUNRPC: Ensure that we wait for connections to complete before retrying
SUNRPC: drop null test before destroy functions
nfs: fix v4.2 SEEK on files over 2 gigs
SUNRPC: Fix races between socket connection and destroy code
nfs: fix pg_test page count calculation
Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount
Merge tag 'sound-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This ended up with a larger set of fixes than wished, unfortunately.
As diffstat shows, the majority of changes are for various ASoC
drivers (Realtek, Wolfson codec drivers, etc), in addition to a couple
of HD-audio regression fixes. All these are reasonably small and
nothing to scare much"
* tag 'sound-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
ALSA: hda - Disable power_save_node for Thinkpads
ALSA: hda/tegra - async probe for avoiding module loading deadlock
ASoC: rt5645: Prevent the pop sound in case of playback and the jack is plugging
ASoC: rt5645: Increase the delay time to remove the pop sound
ASoC: rt5645: Use the type SOC_DAPM_SINGLE_AUTODISABLE to prevent the weird sound in runtime of power up
ASoC: pxa: pxa2xx-ac97: fix dma requestor lines
MAINTAINERS: Update website and git repo for Wolfson Microelectronics
ASoC: fsl_ssi: Fix checking of dai format for AC97 mode
ASoC: wm0010: fix error path
ASoC: wm0010: fix memory leak
ASoC: wm8960: correct the max register value of mic boost pga
ASoC: wm8962: remove 64k sample rate support
ASoC: davinci-mcasp: Fix devm_kasprintf format string
ASoC: fix broken pxa SoC support
ASoC: davinci-mcasp: Set .symmetric_rates = 1 in snd_soc_dai_driver
ASoC: au1x: psc-i2s: Fix unused variable 'ret' warning
ASoC: SPEAr: Make SND_SPEAR_SOC select SND_SOC_GENERIC_DMAENGINE_PCM
ASoC: mediatek: Increase periods_min in capture
ASoC: davinci-mcasp: Revise the FIFO threshold calculation
ASoC: wm8960: correct gain value for input PGA and add microphone PGA
...
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"AMD fixes for bugs introduced in the 4.2 merge window, and a few PPC
bug fixes too"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: disable halt_poll_ns as default for s390x
KVM: x86: fix off-by-one in reserved bits check
KVM: x86: use correct page table format to check nested page table reserved bits
KVM: svm: do not call kvm_set_cr0 from init_vmcb
KVM: x86: trap AMD MSRs for the TSeg base and mask
KVM: PPC: Book3S: Take the kvm->srcu lock in kvmppc_h_logical_ci_load/store()
KVM: PPC: Book3S HV: Pass the correct trap argument to kvmhv_commence_exit
KVM: PPC: Book3S HV: Fix handling of interrupted VCPUs
kvm: svm: reset mmu on VCPU reset
Merge tag 'powerpc-4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up sys_membarrier()
- cxl: Fix lockdep warning while creating afu_err_buff from Vaibhav
* tag 'powerpc-4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
cxl: Fix lockdep warning while creating afu_err_buff attribute
powerpc: Wire up sys_membarrier()
We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.
Architectures are now free to set their own halt_poll_ns
default value.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 22 Sep 2015 08:15:59 +0000 (10:15 +0200)]
KVM: x86: fix off-by-one in reserved bits check
29ecd6601904 ("KVM: x86: avoid uninitialized variable warning",
2015-09-06) introduced a not-so-subtle problem, which probably
escaped review because it was not part of the patch context.
Before the patch, leaf was always equal to iterator.level. After,
it is equal to iterator.level - 1 in the call to is_shadow_zero_bits_set,
and when is_shadow_zero_bits_set does another "-1" the check on
reserved bits becomes incorrect. Using "iterator.level" in the call
fixes this call trace:
Paolo Bonzini [Tue, 22 Sep 2015 21:02:14 +0000 (23:02 +0200)]
KVM: x86: use correct page table format to check nested page table reserved bits
Intel CPUID on AMD host or vice versa is a weird case, but it can
happen. Handle it by checking the host CPU vendor instead of the
guest's in reset_tdp_shadow_zero_bits_mask. For speed, the
check uses the fact that Intel EPT has an X (executable) bit while
AMD NPT has NX.
Paolo Bonzini [Mon, 21 Sep 2015 05:46:55 +0000 (07:46 +0200)]
KVM: svm: do not call kvm_set_cr0 from init_vmcb
kvm_set_cr0 may want to call kvm_zap_gfn_range and thus access the
memslots array (SRCU protected). Using a mini SRCU critical section
is ugly, and adding it to kvm_arch_vcpu_create doesn't work because
the VMX vcpu_create callback calls synchronize_srcu.
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-i38/17000:
#0: (&(&kvm->mmu_lock)->rlock){+.+...}, at: kvm_zap_gfn_range+0x24/0x1a0 [kvm]
This patch fixes a v4.2+ regression introduced by commit c04a6091
that removed support for obsolete sync-and-steering markers usage
as originally defined in RFC-3720.
The regression would involve attempting to send OFMarker=No +
IFMarker=No keys during opertional negotiation login phase,
including when initiators did not actually propose these keys.
The result for MSFT iSCSI initiators would be random junk in
TCP stream after the last successful login request was been sent
signaling the move to full feature phase (FFP) operation.
To address this bug, go ahead and avoid negotiating these keys
by default unless the initiator explicitly proposes them, but
still respond to them with 'No' if they are proposed.
This patch allows target_sense_desc_format() to be called without a
valid se_device pointer, which can occur during an early exception
ahead of transport_lookup_cmd_lun() setting up se_cmd->se_device.
This addresses a v4.3-rc1 specific NULL pointer dereference
regression introduced by commit 4e4937e8.
Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Propigate backend read-only to core_tpg_add_lun
This patch adds a DF_READ_ONLY flag that is used by IBLOCK to
signal when a backend has been set to read-only mode, in order
to propigate read-only status up to core_tpg_add_lun() for all
future LUN fabric exports.
With this is place, existing emulation for reporting read-only
in spc_emulate_modesense() and normal transport_lookup_cmd_lun()
TCM_WRITE_PROTECTED status checking just works as expected.
Reported-by: Joeue Deng <joeue404@gmail.com> Reported-by: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a v4.2+ regression introduced by commit 79dc9c9e86
where lookup of t10_pr_registration->pr_reg_deve and associated
->pr_kref get was missing from __core_scsi3_do_alloc_registration(),
which is responsible for setting DEF_PR_REG_ACTIVE.
This would result in REGISTER operations completing successfully,
but subsequent core_scsi3_pr_seq_non_holder() checking would fail
with !DEF_PR_REG_ACTIVE -> RESERVATION CONFLICT status.
Update __core_scsi3_add_registration() to drop ->pr_kref reference
after registration and any optional ALL_TG_PT=1 processing has
completed. Update core_scsi3_decode_spec_i_port() to release
the new parent local_pr_reg->pr_kref as well.
Also, update __core_scsi3_check_aptpl_registration() to perform
the same target_nacl_find_deve() lookup + ->pr_kref get, now that
__core_scsi3_add_registration() expects to drop the reference.
Finally, since there are cases when se_dev_entry->se_lun_acl can
still be dereferenced in core_scsi3_lunacl_undepend_item() while
holding ->pr_kref, go ahead and move explicit rcu_assign_pointer()
NULL assignments within core_disable_device_list_for_node() until
after orig->pr_comp finishes.
Reported-by: Scott L. Lykens <scott@lykens.org> Tested-by: Scott L. Lykens <scott@lykens.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Lee Duncan <lduncan@suse.com> Cc: <stable@vger.kernel.org> # v4.2+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
David S. Miller [Fri, 25 Sep 2015 06:04:53 +0000 (23:04 -0700)]
Merge branch 'phy-mdio-refcnt'
Russell King says:
====================
Phy, mdiobus, and netdev struct device fixes
The third version of this series fixes the build error which David
identified, and drops the broken changes for the Cavium Thunger BGX
ethernet driver as this driver requires some complex changes to
resolve the leakage - and this is best done by people who can test
the driver.
Compared to v2, the only patch which has changed is patch 6
"net: fix phy refcounting in a bunch of drivers"
I _think_ I've been able to build-test all the drivers touched by
that patch to some degree now, though several of them needed the
Kconfig hacked to allow it (not all had || COMPILE_TEST clause on
their dependencies.)
Previous cover letters below:
This is the second version of the series, with the comments David had
on the first patch fixed up. Original series description with updated
diffstat below.
While looking at the DSA code, I noticed we have a
of_find_net_device_by_node(), and it looks like users of that are
similarly buggy - it looks like net/dsa/dsa.c is the only user. Fix
that too.
Hi,
While looking at the phy code, I identified a number of weaknesses
where refcounting on device structures was being leaked, where
modules could be removed while in-use, and where the fixed-phy could
end up having unintended consequences caused by incorrect calls to
fixed_phy_update_state().
This patch series resolves those issues, some of which were discovered
with testing on an Armada 388 board. Not all patches are fully tested,
particularly the one which touches several network drivers.
When resolving the struct device refcounting problems, several different
solutions were considered before settling on the implementation here -
one of the considerations was to avoid touching many network drivers.
The solution here is:
phy_attach*() - takes a refcount
phy_detach*() - drops the phy_attach refcount
Provided drivers always attach and detach their phys, which they should
already be doing, this should change nothing, even if they leak a refcount.
of_phy_find_device() and of_* functions which use that take
a refcount. Arrange for this refcount to be dropped once
the phy is attached.
This is the reason why the previous change is important - we can't drop
this refcount taken by of_phy_find_device() until something else holds
a reference on the device. This resolves the leaked refcount caused by
using of_phy_connect() or of_phy_attach().
Even without the above changes, these drivers are leaking by calling
of_phy_find_device(). These drivers are addressed by adding the
appropriate release of that refcount.
The mdiobus code also suffered from the same kind of leak, but thankfully
this only happened in one place - the mdio-mux code.
I also found that the try_module_get() in the phy layer code was utterly
useless: phydev->dev.driver was guaranteed to always be NULL, so
try_module_get() was always being called with a NULL argument. I proved
this with my SFP code, which declares its own MDIO bus - the module use
count was never incremented irrespective of how I set the MDIO bus up.
This allowed the MDIO bus code to be removed from the kernel while there
were still PHYs attached to it.
One other bug was discovered: while using in-band-status with mvneta, it
was found that if a real phy is attached with in-band-status enabled,
and another ethernet interface is using the fixed-phy infrastructure, the
interface using the fixed-phy infrastructure is configured according to
the other interface using the in-band-status - which is caused by the
fixed-phy code not verifying that the phy_device passed in is actually
a fixed-phy device, rather than a real MDIO phy.
Lastly, having mdio_bus reversing phy_device_register() internals seems
like a layering violation - it's trivial to move that code to the phy
device layer.
====================
Tested-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:33 +0000 (20:36 +0100)]
net: fix net_device refcounting
of_find_net_device_by_node() uses class_find_device() internally to
lookup the corresponding network device. class_find_device() returns
a reference to the embedded struct device, with its refcount
incremented.
Add a comment to the definition in net/core/net-sysfs.c indicating the
need to drop this refcount, and fix the DSA code to drop this refcount
when the OF-generated platform data is cleaned up and freed. Also
arrange for the ref to be dropped when handling errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:28 +0000 (20:36 +0100)]
phy: add phy_device_remove()
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:23 +0000 (20:36 +0100)]
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
Validate that the phy_device passed into fixed_phy_update_state() is a
fixed-phy device before walking the list of phys for a fixed phy at the
same address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:18 +0000 (20:36 +0100)]
net: fix phy refcounting in a bunch of drivers
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d790a ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:13 +0000 (20:36 +0100)]
of_mdio: fix MDIO phy device refcounting
bus_find_device() is defined as:
* This is similar to the bus_for_each_dev() function above, but it
* returns a reference to a device that is 'found' for later use, as
* determined by the @match callback.
and it does indeed return a reference-counted pointer to the device:
while ((dev = next_device(&i)))
if (match(dev, data) && get_device(dev))
^^^^^^^^^^^^^^^
break;
klist_iter_exit(&i);
return dev;
What that means is that when we're done with the struct device, we must
drop that reference. Neither of_phy_connect() nor of_phy_attach() did
this when phy_connect_direct() or phy_attach_direct() failed.
With our previous patch, phy_connect_direct() and phy_attach_direct()
take a new refcount on the phy device when successful, so we can drop
our local reference immediatley after these functions, whether or not
they succeeded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:08 +0000 (20:36 +0100)]
phy: add proper phy struct device refcounting
Take a refcount on the phy struct device when the phy device is attached
to a network device, and drop it after it's detached. This ensures that
a refcount is held on the phy device while the device is being used by
a network device, thereby preventing the phy_device from being
unexpectedly kfree()'d by phy_device_release().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:02 +0000 (20:36 +0100)]
phy: fix mdiobus module safety
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Current users of of_mdio_find_bus() leak a struct device refcount, as
they fail to clean up the reference obtained inside class_find_device().
Fix the DSA code to properly refcount the returned MDIO bus by:
1. taking a reference on the struct device whenever we assign it to
pd->chip[x].host_dev.
2. dropping the reference when we overwrite the existing reference.
3. dropping the reference when we free the data structure.
4. dropping the initial reference we obtained after setting up the
platform data structure, or on failure.
In step 2 above, where we obtain a new MDIO bus, there is no need to
take a reference on it as we would only have to drop it immediately
after assignment again, iow:
put_device(cd->host_dev); /* drop original assignment ref */
cd->host_dev = get_device(&mdio_bus_switch->dev); /* get our ref */
put_device(&mdio_bus_switch->dev); /* drop of_mdio_find_bus ref */
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log