Nicolin Chen [Fri, 15 Nov 2013 06:31:11 +0000 (14:31 +0800)]
ARM: dts: imx: specify the value of audmux pinctrl instead of 0x80000000
We must specify the value of audmux pinctrl if we want to use pinctrl_pm().
Thus change bypass value 0x80000000 to what we exactly need.
This patch also seperately unset PUE bit for TXD so that IOMUX won't pull
up/down the pin after turning into tristate. When we use SSI normal mode to
playback monaural audio via I2S signal, there'd be a pulled curve occur to
its signal at the second slot if setting PUE bit for TXD. And it will make
the second channel to play a constant noise. So by keeping the signal level
in the second slot, we can get a constant high level signal (-1) or a low
level one (0).
This patch updates i.MX51 CPU node:
- Alias for CPU is added to allow using this node in the parent DTS files.
- Removed useless "clock_names" property.
- "clock-latency" value increased to safe using with 32 kHz OSC.
- Defined operating points voltages and "voltage tolerance" properties.
Values are safe for both commercial and industrial CPU variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Wed, 6 Nov 2013 07:55:46 +0000 (15:55 +0800)]
ARM: dts: imx: use generic node name for fixed regulator
The device tree specification recommends that generic name should be
used for nodes. So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.
Shawn Guo [Mon, 4 Nov 2013 08:24:32 +0000 (16:24 +0800)]
ARM: dts: imx50: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Mon, 4 Nov 2013 08:05:37 +0000 (16:05 +0800)]
ARM: dts: imx51: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Mon, 4 Nov 2013 06:45:46 +0000 (14:45 +0800)]
ARM: dts: imx53: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Mon, 4 Nov 2013 02:49:04 +0000 (10:49 +0800)]
ARM: dts: imx6sl: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Shawn Guo [Wed, 23 Oct 2013 07:36:09 +0000 (15:36 +0800)]
ARM: dts: imx6qdl: make pinctrl nodes board specific
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts. However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected. This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board. It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.
The patch provides a solution to avoid this device tree bloating problem
while still keeping boards share the common pinctrl setting data by
using DTC macro support. It creates <soc>-pingrp.h and move all those
pinctrl setting data into there as macro definitions. The <board>.dts
will instead define the pinctrl setting nodes that are necessary for the
board by referring to the macros in <soc>-pingrp.h, so that only the
pinctrl setting data that will be used by the board will get compiled
into the DTB for the board.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral. Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Valentin Raevsky [Tue, 29 Oct 2013 12:11:43 +0000 (14:11 +0200)]
ARM: dts: Add initial support for cm-fx6.
Add initial support for cm-fx6 module.
cm-fx6 is a module based on mx6q SoC with the following features:
- Up to 4GB of DDR3
- 1 LCD/DVI output port
- 1 HDMI output port
- 2 LVDS LCD ports
- Gigabit Ethernet
- Analog Audio
- CAN
- SATA
- NAND
- PCIE
This patch allows to boot up the module, configures the serial console,
the Ethernet adapter and the heartbeat led.
Denis Carikli [Wed, 23 Oct 2013 09:09:53 +0000 (11:09 +0200)]
ARM: dts: Add support for the cpuimx51 board from Eukrea and its baseboard.
The following devices/functionalities were added:
* Main and secondary UARTs.
* i2c and the pcf8563 device.
* Ethernet.
* NAND.
* The BP1 button.
* The LED.
* Watchdog
* SD.
Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: devicetree@vger.kernel.org Cc: Sascha Hauer <kernel@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: Eric Bénard <eric@eukrea.com> Signed-off-by: Denis Carikli <denis@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tim Harvey [Wed, 23 Oct 2013 04:51:26 +0000 (21:51 -0700)]
ARM: dts: add Gateworks Ventana support
The Gateworks Ventana product family consists of several baseboard designs
based on the Freescale i.MX6 family of processors. Each baseboard has a
different set of possible features.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Marek Vasut [Fri, 22 Nov 2013 11:05:02 +0000 (12:05 +0100)]
ARM: imx: imx53: Add SATA PHY clock
Add SATA PHY clock which are derived from the USB PHY1 clock. Note that this
patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA
driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to
work correctly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Richard Zhu <r65037@freescale.com> Cc: Tejun Heo <tj@kernel.org> Cc: Linux-IDE <linux-ide@vger.kernel.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Anson Huang [Fri, 15 Nov 2013 18:14:18 +0000 (13:14 -0500)]
ARM: imx: clk: correct arm clock usecount
ARM clock is sourcing from pll1_sw, and pll1_sw can be either from
pll1_sys or step, so we should enable arm clock during clock
initialization instead of pll1_sys, otherwise, arm clock's usecount
would be incorrect and PLL1 will never be disabled even it is not
used.
Fabio Estevam [Tue, 12 Nov 2013 22:39:12 +0000 (20:39 -0200)]
ARM: imx_v6_v7_defconfig: Select CONFIG_HIGHMEM
Booting a mx6q wandboard with 2GB of RAM we see the following on boot:
Booting Linux on physical CPU 0x0
Linux version 3.12.0-next-20131112+ (fabio@fabio-Latitude-E6410) (gcc version 43
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Wandboard i.MX6 Quad Board
Truncating RAM at 10000000-8fffffff to -7f7fffff (vmalloc region overlap)
...
Select CONFIG_HIGHMEM to avoid the vmalloc region overlap.
Greg Ungerer [Mon, 4 Nov 2013 00:13:40 +0000 (10:13 +1000)]
ARM: imx: add support code for IMX50 based machines
Add machine support code for the Freescale IMX50 SoC.
The IMX50 is quite similar to the Freescale IMX53, and contains many of the
same periperhal hardware modules, at the same address offsets as the IMX53.
(Notable exceptions are that the IMX50 contains no CAN bus hardware, less
GPIO, no VPU, it does contain an Electrophoretic display controller though).
This support code uses some of the IMX53 setup code to reduce duplication
of what would be identical init IO setup.
The code for irq priorisation support doesn't have any in-tree users and
the Kconfig description does wrong promises because nowadays irq
handlers are called with irqs disabled, so no high prioritized irq can
interrupt a lower prioritized handler.
Shawn Guo [Fri, 1 Nov 2013 08:39:28 +0000 (16:39 +0800)]
ARM: imx: remove mxc_iomux_v3_init() call from imx53_init_early()
Today, imx53 handles iomux configuration using pinctrl driver, so
mxc_iomux_v3_init() call in imx53_init_early() is there for nothing.
Remove the call from there.
Tim Harvey [Wed, 23 Oct 2013 04:51:28 +0000 (21:51 -0700)]
ARM: imx: add PCI fixup for PEX860X on Gateworks board
The PEX860X has GPIO's which are used for PCI Reset lines on the
Gateworks Ventana boards. The GPIO's need to be set as output
level high so as to allow the PCIe devices to come out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Linus Torvalds [Fri, 6 Dec 2013 16:34:16 +0000 (08:34 -0800)]
Merge tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"A regression showed up that there's a large delay when enabling all
events. This was prevalent when FTRACE_SELFTEST was enabled which
enables all events several times, and caused the system bootup to
pause for over a minute.
This was tracked down to an addition of a synchronize_sched()
performed when system call tracepoints are unregistered.
The synchronize_sched() is needed between the unregistering of the
system call tracepoint and a deletion of a tracing instance buffer.
But placing the synchronize_sched() in the unreg of *every* system
call tracepoint is a bit overboard. A single synchronize_sched()
before the deletion of the instance is sufficient"
* tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Only run synchronize_sched() at instance deletion time
Linus Torvalds [Fri, 6 Dec 2013 16:30:18 +0000 (08:30 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of nine fixes (and one author update).
The libsas one should fix discovery in eSATA devices, the WRITE_SAME
one is the largest, but it should fix a lot of problems we've been
getting with the emulated RAID devices (they've been effectively lying
about support and then firmware has been choking on the commands).
The rest are various crash, hang or warn driver fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bfa: Fix crash when symb name set for offline vport
[SCSI] enclosure: fix WARN_ON in dual path device removing
[SCSI] pm80xx: Tasklets synchronization fix.
[SCSI] pm80xx: Resetting the phy state.
[SCSI] pm80xx: Fix for direct attached device.
[SCSI] pm80xx: Module author addition
[SCSI] hpsa: return 0 from driver probe function on success, not 1
[SCSI] hpsa: do not discard scsi status on aborted commands
[SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
[SCSI] libsas: fix usage of ata_tf_to_fis
Linus Torvalds [Fri, 6 Dec 2013 16:28:35 +0000 (08:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull IMA fixes from James Morris:
"Here are two more fixes for IMA"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: properly free ima_template_entry structures
ima: Do not free 'entry' before it is initialized
Linus Torvalds [Fri, 6 Dec 2013 16:27:47 +0000 (08:27 -0800)]
Merge tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Various DT binding documentation updates
- Add Kumar Gala and remove Stephen Warren as DT binding maintainers
* tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt: binding: reword PowerPC 8xxx GPIO documentation
ARM: tegra: delete nvidia,tegra20-spi.txt binding
hwmon: ntc_thermistor: Fix typo (pullup-uV -> pullup-uv)
of: add vendor prefix for GMT
clk: exynos: Fix typos in DT bindings documentation
of: Add vendor prefix for LG Corporation
Documentation: net: fsl-fec.txt: Add phy-supply entry
ARM: dts: doc: Document missing binding for omap5-mpu
dt-bindings: add ARMv8 PMU binding
MAINTAINERS: remove swarren from DT bindings
MAINTAINERS: Add Kumar to Device Tree Binding maintainers group
Gu Zheng [Wed, 4 Dec 2013 10:19:06 +0000 (18:19 +0800)]
aio: clean up aio ring in the fail path
Clean up the aio ring file in the fail path of aio_setup_ring
and ioctx_alloc. And maybe it can fix the GPF issue reported by
Dave Jones:
https://lkml.org/lkml/2013/11/25/898
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Linus Torvalds [Fri, 6 Dec 2013 02:26:40 +0000 (18:26 -0800)]
Merge tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to avoid
garbage sysfs files from being left behind in case of a suspend error
- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.
- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled from
the kernel command line. From Konrad Rzeszutek Wilk.
- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.
- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.
- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.
- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.
* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PowerCap: Fix mode for energy counter
PNP: fix restoring devices after hibernation
cpuidle: Check for dev before deregistering it.
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
intel_idle: Fixed C6 state on Avoton/Rangeley processors
Linus Torvalds [Thu, 5 Dec 2013 23:33:27 +0000 (15:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. It contains:
- A fix for a use-after-free of a request in blk-mq. From Ming Lei
- A fix for a blk-mq bug that could attempt to dereference a NULL rq
if allocation failed
- Two xen-blkfront small fixes
- Cleanup of submit_bio_wait() type uses in the kernel, unifying
that. From Kent
- A fix for 32-bit blkg_rwstat reading. I apologize for this one
looking mangled in the shortlog, it's entirely my fault for missing
an empty line between the description and body of the text"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix use-after-free of request
blk-mq: fix dereference of rq->mq_ctx if allocation fails
block: xen-blkfront: Fix possible NULL ptr dereference
xen-blkfront: Silence pfn maybe-uninitialized warning
block: submit_bio_wait() conversions
Update of blkg_stat and blkg_rwstat may happen in bh context
Linus Torvalds [Thu, 5 Dec 2013 21:05:48 +0000 (13:05 -0800)]
Merge tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for a NFSv4.1 delegation and state recovery deadlock
- Stable fix for a loop on irrecoverable errors when returning
delegations
- Fix a 3-way deadlock between layoutreturn, open, and state recovery
- Update the MAINTAINERS file with contact information for Trond
Myklebust
- Close needs to handle NFS4ERR_ADMIN_REVOKED
- Enabling v4.2 should not recompile nfsd and lockd
- Fix a couple of compile warnings
* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix do_div() warning by instead using sector_div()
MAINTAINERS: Update contact information for Trond Myklebust
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
SUNRPC: do not fail gss proc NULL calls with EACCES
NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
NFSv4: Update list of irrecoverable errors on DELEGRETURN
NFSv4 wait on recovery for async session errors
NFS: Fix a warning in nfs_setsecurity
NFS: Enabling v4.2 should not recompile nfsd and lockd
Tony Lu [Thu, 5 Dec 2013 20:36:54 +0000 (15:36 -0500)]
ftrace: default to tilegx if ARCH=tile is specified
This matches the existing behavior in arch/tile/Makefile for defconfig.
Reported-by: fengguang.wu@intel.com Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Tony Lu <zlu@tilera.com> Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Steven Rostedt [Tue, 3 Dec 2013 17:41:20 +0000 (12:41 -0500)]
tracing: Only run synchronize_sched() at instance deletion time
It has been reported that boot up with FTRACE_SELFTEST enabled can take a
very long time. There can be stalls of over a minute.
This was tracked down to the synchronize_sched() called when a system call
event is disabled. As the self tests enable and disable thousands of events,
this makes the synchronize_sched() get called thousands of times.
The synchornize_sched() was added with d562aff93bfb53 "tracing: Add support
for SOFT_DISABLE to syscall events" which caused this regression (added
in 3.13-rc1).
The synchronize_sched() is to protect against the events being accessed
when a tracer instance is being deleted. When an instance is being deleted
all the events associated to it are unregistered. The synchronize_sched()
makes sure that no more users are running when it finishes.
Instead of calling synchronize_sched() for all syscall events, we only
need to call it once, after the events are unregistered and before the
instance is deleted. The event_mutex is held during this action to
prevent new users from enabling events.
Link: http://lkml.kernel.org/r/20131203124120.427b9661@gandalf.local.home Reported-by: Petr Mladek <pmladek@suse.cz> Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Acked-by: Petr Mladek <pmladek@suse.cz> Tested-by: Petr Mladek <pmladek@suse.cz> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Thu, 5 Dec 2013 17:55:20 +0000 (09:55 -0800)]
Merge tag 'fbdev-fixes-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull minor fbdev fixes from Tomi Valkeinen.
* tag 'fbdev-fixes-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: vt8500: fix error handling in probe()
atmel_lcdfb: fix module autoload
fbdev: sh_mobile_meram: Fix defined but not used compiler warnings
video: kyro: fix incorrect sizes when copying to userspace
ARM: OMAPFB: panel-sony-acx565akm: fix bad unlock balance
Linus Torvalds [Thu, 5 Dec 2013 17:54:35 +0000 (09:54 -0800)]
Merge tag 'sound-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A usual pattern of half ASoC and half HD-audio fixes, although
HD-audio fixups have more volumes, in addition to a couple of trivial
fixes. Nothing to worry much is found here.
For ASoC side: a few fixes for PCM rate constraints calculations,
regmap byte-order fix, the rest driver specific fixes (atmel, fsl,
omap, kirkwood, wm codecs).
For HD-audio: Dell headset and mono out fix, ELD update in polling
mode, ALC283 Chromebook fixes, a few fixes for old AD codecs and
MBA2, one regression fix"
* tag 'sound-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: hda - Fix silent output on MacBook Air 2,1
ALSA: hda - Fix missing ELD info when using jackpoll_ms parameter
ALSA: hda/realtek - remove hp_automute_hook from alc283_fixup_chromebook
ASoC: wm8731: fix dsp mode configuration
ALSA: hda/realtek - Independent of model for HP
ALSA: hda - Fix headset mic input after muted internal mic (Dell/Realtek)
ALSA: hda - Use always amps for auto-mute on AD1986A codec
ALSA: hda/analog - Handle inverted EAPD properly in vmaster hook
ALSA: hda - Another fixup for ASUS laptop with ALC660 codec
ALSA: atmel: Fix possible array overflow
ALSA: hda - Fix complete_all() timing in deferred probes
ALSA: hda - Fix bad EAPD setup for HP machines with AD1984A
ASoC: core: fix devres parameter in devm_snd_soc_register_card()
ASoC: omap: n810: Convert to clk_prepare_enable/clk_disable_unprepare
ASoC: fsl: set correct platform drvdata in pcm030_fabric_probe()
ASoC: fsl: imx-pcm-fiq: Remove unused 'runtime' variable
ASoC: fsl: imx-pcm-fiq: remove bogus period delta calculation
ALSA: hda - Fix silent output on ASUS W7J laptop
ASoC: core: Use consistent byte ordering in snd_soc_bytes_get
ALSA: dice: fix array limits in dice_proc_read()
...
Linus Torvalds [Thu, 5 Dec 2013 05:45:21 +0000 (21:45 -0800)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 and EFI fixes from Peter Anvin:
"Half of these are EFI-related:
The by far biggest change is the change to hold off the deletion of a
sysfs entry while a backend scan is in progress. This is to avoid
calling kmemdup() while under a spinlock.
The other major change is for each entry in the EFI pstore backend to
get a unique identifier, as required by the pstore filesystem proper.
The other changes are:
A fix to the recent consolidation and optimization of using "asm goto"
with read-modify-write operation, which broke the bitops; specifically
in such a way that we could end up generating invalid code.
A build hack to make sure we compile with -mno-sse. icc, and most
likely future versions of gcc, can generate SSE instructions unless we
tell it not to.
A comment-only patch to a change the was due in part to an unpublished
erratum; now when the erratum is published we want to add a comment
explaining why"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic, doc: Justification for disabling IO APIC before Local APIC
x86, bitops: Correct the assembly constraints to testing bitops
x86-64, build: Always pass in -mno-sse
efi-pstore: Make efi-pstore return a unique id
x86/efi: Fix earlyprintk off-by-one bug
efivars, efi-pstore: Hold off deletion of sysfs entry until the scan is completed
Fenghua Yu [Thu, 5 Dec 2013 00:07:49 +0000 (16:07 -0800)]
x86/apic, doc: Justification for disabling IO APIC before Local APIC
Since erratum AVR31 in "Intel Atom Processor C2000 Product Family
Specification Update" is now published, I added a justification
comment for disabling IO APIC before Local APIC, as changed in commit:
522e66464467 x86/apic: Disable I/O APIC before shutdown of the local APIC
As per the documentation of powercap sysfs, energy_uj field is read only,
if it can't be reset. Currently it always allows write but will fail,
if there is no reset callback.
Changing mode field, to read only if there is no reset callback.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reported-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
H. Peter Anvin [Wed, 4 Dec 2013 22:31:28 +0000 (14:31 -0800)]
x86, bitops: Correct the assembly constraints to testing bitops
In checkin:
0c44c2d0f459 x86: Use asm goto to implement better modify_and_test() functions
the various functions which do modify and test were unified and
optimized using "asm goto". However, this change missed the detail
that the bitops require an "Ir" constraint rather than an "er"
constraint ("I" = integer constant from 0-31, "e" = signed 32-bit
integer constant). This would cause code to miscompile if these
functions were used on constant bit positions 32-255 and the build to
fail if used on constant bit positions above 255.
Add the constraints as a parameter to the GEN_BINARY_RMWcc() macro to
avoid this problem.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/529E8719.4070202@zytor.com
Helge Deller [Mon, 2 Dec 2013 18:59:31 +0000 (19:59 +0100)]
nfs: fix do_div() warning by instead using sector_div()
When compiling a 32bit kernel with CONFIG_LBDAF=n the compiler complains like
shown below. Fix this warning by instead using sector_div() which is provided
by the kernel.h header file.
fs/nfs/blocklayout/extents.c: In function ‘normalize’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast [enabled by default]
fs/nfs/blocklayout/extents.c:47:13: note: in expansion of macro ‘do_div’
nfs/blocklayout/extents.c:47:2: warning: right shift count >= width of type [enabled by default]
fs/nfs/blocklayout/extents.c:47:2: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected ‘uint64_t *’ but argument is of type ‘sector_t *’
extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
Trond Myklebust [Wed, 4 Dec 2013 17:09:45 +0000 (12:09 -0500)]
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
Andy Adamson reports:
The state manager is recovering expired state and recovery OPENs are being
processed. If kswapd is pruning inodes at the same time, a deadlock can occur
when kswapd calls evict_inode on an NFSv4.1 inode with a layout, and the
resultant layoutreturn gets an error that the state mangager is to handle,
causing the layoutreturn to wait on the (NFS client) cl_rpcwaitq.
At the same time an open is waiting for the inode deletion to complete in
__wait_on_freeing_inode.
If the open is either the open called by the state manager, or an open from
the same open owner that is holding the NFSv4 sequence id which causes the
OPEN from the state manager to wait for the sequence id on the Seqid_waitqueue,
then the state is deadlocked with kswapd.
The fix is simply to have layoutreturn ignore all errors except NFS4ERR_DELAY.
We already know that layouts are dropped on all server reboots, and that
it has to be coded to deal with the "forgetful client model" that doesn't
send layoutreturns.