Commit 50ac23be ("staging:iio:adc:ad7606 add local define for chan_spec
structures.") accidentally removed the scale info_mask flag. This patch
adds it back again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- info_mask was completely gone rather than set to another flag
- IIO_CHAN_INFO_SCALE_SHARED_BIT was not defined; write it out as a shift] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Minchan Kim reports that when a system has many swap areas, and tmpfs
swaps out to the ninth or more, shmem_getpage_gfp()'s attempts to read
back the page cannot locate it, and the read fails with -ENOMEM.
Whoops. Yes, I blindly followed read_swap_header()'s pte_to_swp_entry(
swp_entry_to_pte()) technique for determining maximum usable swap
offset, without stopping to realize that that actually depends upon the
pte swap encoding shifting swap offset to the higher bits and truncating
it there. Whereas our radix_tree swap encoding leaves offset in the
lower bits: it's swap "type" (that is, index of swap area) that was
truncated.
Fix it by reducing the SWP_TYPE_SHIFT() in swapops.h, and removing the
broken radix_to_swp_entry(swp_to_radix_entry()) from read_swap_header().
This does not reduce the usable size of a swap area any further, it
leaves it as claimed when making the original commit: no change from 3.0
on x86_64, nor on i386 without PAE; but 3.0's 512GB is reduced to 128GB
per swapfile on i386 with PAE. It's not a change I would have risked
five years ago, but with x86_64 supported for ten years, I believe it's
appropriate now.
Hmm, and what if some architecture implements its swap pte with offset
encoded below type? That would equally break the maximum usable swap
offset check. Happily, they all follow the same tradition of encoding
offset above type, but I'll prepare a check on that for next.
Reported-and-Reviewed-and-Tested-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.
The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.
In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.
Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-by: bEN <ml_all@circa.be> Reported-by: Ivan Perrone <ivanperrone@hotmail.com> Tested-by: ivan perrone <ivanperrone@hotmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently CDC-ACM devices stay throttled when their TTY is closed while
throttled, stalling further communication attempts after the next open.
Unthrottling during open/activate got lost starting with kernel
3.0.0 and this patch reintroduces it.
Signed-off-by: Otto Meta <otto.patches@sister-shadow.de> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
After commit aaa0ef289afe9186f81e2340114ea413eef0492a "PS3 EHCI QH
read work-around", Terratec Grabby (em28xx) stopped working with AMD
Geode LX 800 (USB controller AMD CS5536). Since this is a PS3 only
fix, the following patch adds a conditional block around it.
Signed-off-by: Ricardo Martins <rasm@fe.up.pt> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
PS3 EHCI HC errata fix 244. The SCC EHCI HC will not correctly perform QH
reads that occur near or span a micro-frame boundry. This is due to a problem
in the Nak Count Reload Control logic (EHCI Specification 1.0 Section 4.9.1).
The work-around for this problem is for the HC driver to set I=1 (inactive) for
QHs with H=1 (list head).
Signed-off-by: Geoff Levand <geoff@infradead.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.
xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.
Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.
This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation"
Signed-off-by: Andiry Xu <andiry.xu@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Ming Lei <ming.lei@canonical.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes a few issues introduced in the recent fix
[f8a9e72d: USB: fix resource leak in xhci power loss path]
- The endpoints listed in bw table are just links and each entry is an
array member of dev->eps[]. But the commit above adds a kfree() call
to these instances, and thus it results in memory corruption.
- It clears only the first entry of rh_bw[], but there can be multiple
ports.
- It'd be safer to clear the list_head of ep as well, not only
removing from the list, as it's checked in
xhci_discover_or_reset_device().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reviewed-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
xhci_free_tt_info() may access the invalid memory when it removes the
last entry but the list is not empty. Then tt_next reaches to the
list head but it still tries to check the tt_info of that entry.
This patch fixes the bug and cleans up the messy code by rewriting
with a simple list_for_each_entry_safe().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce67178ca3c7c7ad534c571bba1e69ebe "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reviewed-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We need to make sure that the USB serial driver we find
matches the USB driver whose probe we are currently
executing. Otherwise we will end up with USB serial
devices bound to the correct serial driver but wrong
USB driver.
An example of such cross-probing, where the usbserial_generic
USB driver has found the sierra serial driver:
May 29 18:26:15 nemi kernel: [ 4442.559246] usbserial_generic 4-4:1.0: Sierra USB modem converter detected
May 29 18:26:20 nemi kernel: [ 4447.556747] usbserial_generic 4-4:1.2: Sierra USB modem converter detected
May 29 18:26:25 nemi kernel: [ 4452.557288] usbserial_generic 4-4:1.3: Sierra USB modem converter detected
sysfs view of the same problem:
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/sierra
-rw-r--r-- 1 root root 4096 May 29 18:23 new_id
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0/ttyUSB0
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB1 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2/ttyUSB1
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3/ttyUSB2
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/usbserial_generic/
total 0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.3 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/generic/
total 0
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
-rw-r--r-- 1 root root 4096 May 29 18:33 new_id
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
So we end up with a mismatch between the USB driver and the
USB serial driver. The reason for the above is simple: The
USB driver probe will succeed if *any* registered serial
driver matches, and will use that serial driver for all
serial driver functions.
This makes ref counting go wrong. We count the USB driver
as used, but not the USB serial driver. This may result
in Oops'es as demonstrated by Johan Hovold <jhovold@gmail.com>:
Fix by only evaluating serial drivers pointing back to the
USB driver we are currently probing. This still allows two
or more drivers to match the same device, running their
serial driver probes to sort out which one to use.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Reviewed-by: Felipe Balbi <balbi@ti.com> Tested-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit 151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Dâniel Fraga <fragabr@gmail.com> Tested-by: Andrey Rahmatullin <wrar@wrar.name> Tested-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The error paths in target_emulate_set_target_port_groups() are all
essentially "rc = -EINVAL; goto out;" but the code at "out:" ignores
rc and always returns success. This means that even if eg explicit
ALUA is turned off, the initiator will always see a good SCSI status
for SET TARGET PORT GROUPS.
Fix this by returning rc as is intended. It appears this bug was
added by the following patch:
Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: we have transport_complete_task()
and not target_complete_cmd()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix memory leak introduced by commit 383cedc3bb435de7a2 ("USB: serial:
full autosuspend support for the option driver") which allocates
usb-serial data but never frees it.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 8b4c6a3ab596961b78465 ("USB: option: Use generic USB wwan code")
moved option port-data allocation to usb_wwan_startup but still cast the
port data to the old struct...
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The low level helper returns 1 on success. The ioctl should however return
0. As this is the only user of the helper return, make the helper return 0 or
an error code.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43009 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Later firmwares for this device now have proper subclass and
protocol info so we can identify it nicely without needing to use
the blacklist. I'm not removing the old 0xff matching as there
may be devices in the field that still need that.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[v2: Editorial changes suggested by Sergei Shtylyov]
These modems use the Qualcomm MSM Interface (QMI) protocol for
management of their CDC ECM like wwan interface. This driver
is perfect for exporting the protocol to userspace.
The created character device will be indistinguishable from a
common AT command based Device Management interface, so
userspace applications must do some intelligent matching
on the USB device.
Cc: Sergei Shtylyov <sshtylyov@mvista.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Oliver Neukum <oneukum@suse.de> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.
BugLink: https://bugs.launchpad.net/bugs/993162 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A few machines with ALC861 & co are reported not to work properly with
the auto-mute feature in software. The auto-mute feature is implemented
in the hardware level, and the jack-detection never works with them.
Also, rename the fixup index as ALC861_FIXUP_* to follow the standard.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add a new flag to indicate that the codec has no jack-detection cap.
This flag should be set for hardwares that have no jack-detect
implementation although the codec chip itself supports it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust filename and context for is_jack_detectable()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2 as instructed: pass bus(trans) to iwl_write_prph()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
did not correctly report supported firmware
for the 6035 device. This patch fixes it. The
minimum supported firmware version for 6035
is v6.
Also correct the minimum supported firmware
version for the 6000g2 series of devices.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2:
- adjust context
- make IWL_DEVICE_6035 identical for IWL_DEVICE_6030 except for the
ucode_api_* fields] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While nfs4_do_open() expects the fmode argument to be restricted to
combinations of FMODE_READ and FMODE_WRITE, both nfs4_atomic_open()
and nfs4_proc_create will pass the nfs_open_context->mode,
which contains the full fmode_t.
This patch ensures that nfs4_do_open strips the other fmode_t bits,
fixing a problem in which the nfs4_do_open call would result in an
unnecessary delegation return.
Reported-by: Fred Isaman <iisaman@netapp.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The statically defined I/O memory regions for the i.MX21 on chip
peripherals and the on board I/O peripherals of the i.MX21ADS board
overlap. This results in a kernel crash during startup. This is fixed
by reducing the memory range for the on board I/O peripherals to the
actually required range.
There is a system hang issue on imx6q which can easily be seen with
running a cpu hotplug stress testing (hotplug secondary cores from
user space via sysfs interface for thousands iterations).
It turns out that the issue is caused by coherency of the cpu that
is being shut down. When shutting down a cpu, we need to have the
cpu exit coherency to prevent it from receiving cache, TLB, or BTB
maintenance operations broadcast by other CPUs in the cluster.
Copy cpu_enter_lowpower() and cpu_leave_lowpower() from mach-vexpress
to have coherency properly handled in platform_cpu_die(), thus fix
the issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id().
This is because smp_processor_id() is not called in preempt safe condition.
To fix this issue, use raw_smp_processor_id instead of smp_processor_id.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Volume updates may not be acted upon if there is no clock applied when
the volume update is written. Ensure this doesn't happen by writing out
registers with volume updates after we enable each of the clocks.
There are more registers updated than before as previously we were
relying on wm_hubs to set those for controls it manages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
usb_ep_ops.disable must clear external copy of the endpoint descriptor,
otherwise musb crashes after loading/unloading several gadget modules
in a row:
Unable to handle kernel paging request at virtual address bf013730
pgd = c0004000
[bf013730] *pgd=8f26d811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1]
Modules linked in: g_cdc [last unloaded: g_file_storage]
CPU: 0 Not tainted (3.2.17 #647)
PC is at musb_gadget_enable+0x4c/0x24c
LR is at _raw_spin_lock_irqsave+0x4c/0x58
[<c027c030>] (musb_gadget_enable+0x4c/0x24c) from [<bf01b760>] (gether_connect+0x3c/0x19c [g_cdc])
[<bf01b760>] (gether_connect+0x3c/0x19c [g_cdc]) from [<bf01ba1c>] (ecm_set_alt+0x15c/0x180 [g_cdc])
[<bf01ba1c>] (ecm_set_alt+0x15c/0x180 [g_cdc]) from [<bf01ecd4>] (composite_setup+0x85c/0xac4 [g_cdc])
[<bf01ecd4>] (composite_setup+0x85c/0xac4 [g_cdc]) from [<c027b744>] (musb_g_ep0_irq+0x844/0x924)
[<c027b744>] (musb_g_ep0_irq+0x844/0x924) from [<c027a97c>] (musb_interrupt+0x79c/0x864)
[<c027a97c>] (musb_interrupt+0x79c/0x864) from [<c027aaa8>] (generic_interrupt+0x64/0x7c)
[<c027aaa8>] (generic_interrupt+0x64/0x7c) from [<c00797cc>] (handle_irq_event_percpu+0x28/0x178)
...
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Xen PV kernels allow access to the APERF/MPERF registers to read the
effective frequency. Access to the MSRs is however redirected to the
currently scheduled physical CPU, making consecutive read and
compares unreliable. In addition each rdmsr traps into the hypervisor.
So to avoid bogus readouts and expensive traps, disable the kernel
internal feature flag for APERF/MPERF if running under Xen.
This will
a) remove the aperfmperf flag from /proc/cpuinfo
b) not mislead the power scheduler (arch/x86/kernel/cpu/sched.c) to
use the feature to improve scheduling (by default disabled)
c) not mislead the cpufreq driver to use the MSRs
This does not cover userland programs which access the MSRs via the
device file interface, but this will be addressed separately.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The 32 bit variant of cbc(aes) decrypt is using instructions requiring
128 bit aligned memory locations but fails to ensure this constraint in
the code. Fix this by loading the data into intermediate registers with
load unaligned instructions.
This fixes reported general protection faults related to aesni.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43223 Reported-by: Daniel <garkein@mailueberfall.de> Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Data valid gets cleared by reading the ISR (status register) and NOT from
reading ODATA (data register). A new data word can become available between
checking ISR and reading ODATA, causing us to reuse the same data word next
time atmel_trng_read() gets called, if that happens before the following
data word is ready.
With this fixed, rngtest no longer complains of 'Continous run' errors.
Before:
rngtest -c 1000 < /dev/hwrng
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 923
rngtest: FIPS 140-2 failures: 77
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 76
rngtest: input channel speed: (min=721.402; avg=46003.510; max=49321.338)Kibitss
rngtest: FIPS tests speed: (min=11.442; avg=12.714; max=12.801)Mibits/s
rngtest: Program run time: 1931860 microseconds
After:
rngtest -c 1000 < /dev/hwrng
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 1000
rngtest: FIPS 140-2 failures: 0
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 0
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=777.518; avg=36988.482; max=43115.342)Kibitss
rngtest: FIPS tests speed: (min=11.951; avg=12.715; max=12.887)Mibits/s
rngtest: Program run time: 2035543 microseconds
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Reported-by: George Pontis <GPontis@z9.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It does not get processed because sched_domain_level_max is 0 at the
time that setup_relax_domain_level() is run.
Simply accept the value as it is, as we don't know the value of
sched_domain_level_max until sched domain construction is completed.
Fix sched_relax_domain_level in cpuset. The build_sched_domain() routine calls
the set_domain_attribute() routine prior to setting the sd->level, however,
the set_domain_attribute() routine relies on the sd->level to decide whether
idle load balancing will be off/on.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20120605184436.GA15668@sgi.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust the filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Andre Przywara [Fri, 23 Mar 2012 09:02:17 +0000 (10:02 +0100)]
hwmon: (fam15h_power) Increase output resolution
On high CPU load the accumulating values in the running_avg_cap
register are very low (below 10), so averaging them too early leads
to unnecessary poor output resolution. Since we pretend to output
micro-Watt we better keep all the bits we have as long as possible.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
(cherry picked from commit 941a956b0e387b21f385f486c34ef67576775cfc)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it
BIOS will switch off the corresponding feature flag on family
15h models 10h-1fh non-desktop CPUs.
The topology extension CPUID leafs are required to detect which
cores belong to the same compute unit. (thread siblings mask is
set accordingly and also correct information about L1i and L2
cache sharing depends on this).
W/o this patch we wouldn't see which cores belong to the same
compute unit and also cache sharing information for L1i and L2
would be incorrect on such systems.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
(cherry picked from commit f7f286a910221ae18b21c18d9d0f4cd88965829f)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently, the APIC LVT interrupt for error thresholding is implicitly
enabled. However, there are models in the F15h range which do not enable
it. Make the code machinery which sets up the APIC interrupt support
an optional setting and add an ->interrupt_capable member to the bank
representation mirroring that capability and enable the interrupt offset
programming only if it is true.
Simplify code and fixup comment style while at it.
This patch is for stable kernels v3.0 to v3.2.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Now we store attr->ino at inode->i_ino, return attr->ino at the
first time and then return inode->i_ino if the attribute timeout
isn't expired. That's wrong on 32 bit platforms because attr->ino
is 64 bit and inode->i_ino is 32 bit in this case.
Fix this by saving 64 bit ino in fuse_inode structure and returning
it every time we call getattr. Also squash attr->ino into inode->i_ino
explicitly.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
[Maarten Lankhorst backported to 3.2,
changing nv_connector->type to nv_connector->dcb->type] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This fixes a problem which can causes kernel oopses while loading
a kernel module.
According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.
This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.
The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code. According to the statements from Freescale, this is
safe from an EABI perspective.
I've tested the fix for kernel 2.6.33 on MPC8541.
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description] Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The SGI Altix UV2 BAU (Broadcast Assist Unit) as used for
tlb-shootdown (selective broadcast mode) always uses UV2
broadcast descriptor format. There is no need to clear the
'legacy' (UV1) mode, because the hardware always uses UV2 mode
for selective broadcast.
But the BIOS uses general broadcast and legacy mode, and the
hardware pays attention to the legacy mode bit for general
broadcast. So the kernel must not clear that mode bit.
Or at least plug another gapping hole. Apparrently hw desingers only
moved the bit field, but did not bother ot re-enumerate the planes
when adding support for a 3rd pipe.
Discovered by i-g-t/flip_test.
This may or may not fix the reference bugzilla, because that one
smells like we have still larger fish to fry.
v2: Fixup the impossible case to catch programming errors, noticed by
Chris Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069 Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- adjust context
- we don't have intel_unpin_fb_obj(); use i915_gem_object_unpin()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Empirical evidence suggests that we need to: On at least one ivb
machine when running the hangman i-g-t test, the rings don't properly
initialize properly - the RING_START registers seems to be stuck at
all zeros.
Holding forcewake around this register init sequences makes chip reset
reliable again. Note that this is not the first such issue:
added delay loops to make RING_START and RING_CTL initialization
reliable on the blt ring at boot-up. So I guess it won't hurt if we do
this unconditionally for all force_wake needing gpus.
To avoid copy&pasting of the HAS_FORCE_WAKE check I've added a new
intel_info bit for that.
v2: Fixup missing commas in static struct and properly handling the
error case in init_ring_common, both noticed by Jani Nikula.
Reported-and-tested-by: Yang Guang <guang.a.yang@intel.com> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522 Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- drop changes to Haswell device information
- NEEDS_FORCE_WAKE didn't refer to Valley View anyway] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
By correctly describing the rinbuffers as being in the GTT domain, it
appears that we are more careful with the management of the CPU cache
upon resume and so prevent some coherency issue when submitting commands
to the GPU later. A secondary effect is that the debug logs are then
consistent with the actual usage (i.e. they no longer describe the
ringbuffers as being in the CPU write domain when we are accessing them
through an wc iomapping.)
Reported-and-tested-by: Daniel Gnoutcheff <daniel@gnoutcheff.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41092 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ext3 filesystems that are converted to use as many ext4 file system
features as possible will enable uninit_bg to speed up e2fsck times.
These file systems will have a native ext3 layout of inode tables and
block allocation bitmaps (as opposed to ext4's flex_bg layout).
Unfortunately, in these cases, when first allocating a block in an
uninitialized block group, ext4 would incorrectly calculate the number
of free blocks in that block group, and then errorneously report that
the file system was corrupt:
EXT4-fs error (device vdd): ext4_mb_generate_buddy:741: group 30, 32254 clusters in bitmap, 32258 in gd
Commit 7990696 uses the ext4_{set,clear}_inode_flags() functions to
change the i_flags automatically but fails to remove the error setting
of i_flags. So we still have the problem of trashing state flags.
Fix this by removing the assignment.
Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In commit 353eb83c we removed i_state_flags with 64-bit longs, But
when handling the EXT4_IOC_SETFLAGS ioctl, we replace i_flags
directly, which trashes the state flags which are stored in the high
32-bits of i_flags on 64-bit platforms. So use the the
ext4_{set,clear}_inode_flags() functions which use atomic bit
manipulation functions instead.
Reported-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
asix driver drops 8021Q full size frames because it doesn't take into
account VLAN header size.
Tested on AX88772 adapter.
Signed-off-by: Eric Dumazet <edumazet@google.com> CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> CC: Allan Chou <allan@asix.com.tw> CC: Trond Wuellner <trond@chromium.org> CC: Grant Grundler <grundler@chromium.org> CC: Paul Stewart <pstew@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: no offset used in asix_rx_fixup()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Programs using /proc/kpageflags need to know about the various flags. The
<linux/kernel-page-flags.h> provides them and the comments in the file
indicate that it is supposed to be used by user-level code. But the file
is not installed.
Install the headers and mark the unstable flags as out-of-bounds. The
page-type tool is also adjusted to not duplicate the definitions
Signed-off-by: Ulrich Drepper <drepper@gmail.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context; drop change to missing tools/vm/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The memory the parameter __key points to is used as an iterator in
btree_get_prev(), so if we save off a bkey() pointer in retry_key and
then assign that to __key, we'll end up corrupting the btree internals
when we do eg
longcpy(__key, bkey(geo, node, i), geo->keylen);
to return the key value. What we should do instead is use longcpy() to
copy the key value that retry_key points to __key.
This can cause a btree to get corrupted by seemingly read-only
operations such as btree_for_each_safe.
[akpm@linux-foundation.org: avoid the double longcpy()] Signed-off-by: Roland Dreier <roland@purestorage.com> Acked-by: Joern Engel <joern@logfs.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
At some point pci_get_bus_and_slot started to enable
interrupts. Since this function is used in the
amd_iommu_resume path it will enable interrupts on resume
which causes a warning. The fix will use a cached pointer
to the root-bridge to re-enable the IOMMU in case the BIOS
is broken.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Convert to use O_DSYNC for all cases at FILEIO backend creation time to
avoid the extra syncing of pure timestamp updates with legacy O_SYNC during
default operation as recommended by hch. Continue to do this independently of
Write Cache Enable (WCE) bit, as WCE=0 is currently the default for all backend
devices and enabled by user on per device basis via attrib/emulate_write_cache.
This patch drops the now unnecessary fd_buffered_io= token usage that was
originally signalling when to explictly disable O_SYNC at backend creation
time for buffered I/O operation. This can end up being dangerous for a number
of reasons during physical node failure, so go ahead and drop this option
for now when O_DSYNC is used as the default.
Also allow explict FUA WRITEs -> vfs_fsync_range() call to function in
fd_execute_cmd() independently of WCE bit setting.
Reported-by: Christoph Hellwig <hch@lst.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[bwh: Backported to 3.2:
- We have fd_do_task() and not fd_execute_cmd()
- Various fields are in struct se_task rather than struct se_cmd
- fd_create_virtdevice() flags initialisation hasn't been cleaned up]
We only need to regenerate the sysfs files when the capacity units
change, avoid the update otherwise.
The origin of this issue is dates way back to 2.6.38: da8aeb92d4853f37e281f11fddf61f9c7d84c3cd
(ACPI / Battery: Update information on info notification and resume)
Signed-off-by: Andy Whitcroft <apw@canonical.com> Tested-by: Ralf Jung <post@ralfj.de> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Corrects the function that determines the esp payload size. The calculations
done in esp{4,6}_get_mtu() lead to overlength frames in transport mode for
certain mtu values and suboptimal frames for others.
According to what is done, mainly in esp{,6}_output() and tcp_mtu_to_mss(),
net_header_len must be taken into account before doing the alignment
calculation.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
At the beginning of __skb_cow, headroom gets set to a minimum of
NET_SKB_PAD. This causes unnecessary reallocations if the buffer was not
cloned and the headroom is just below NET_SKB_PAD, but still more than the
amount requested by the caller.
This was showing up frequently in my tests on VLAN tx, where
vlan_insert_tag calls skb_cow_head(skb, VLAN_HLEN).
Locally generated packets should have enough headroom, and for forward
paths, we already have NET_SKB_PAD bytes of headroom, so we don't need to
add any extra space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Vlad Yaseivch <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
The r8169 may get stuck or show bad behaviour after activating TSO :
the net_device is not stopped when it has no more TX descriptors.
This problem comes from TX_BUFS_AVAIL which may reach -1 when all
transmit descriptors are in use. The patch simply tries to keep positive
values.
Tested with 8111d(onboard) on a D510MO, and with 8111e(onboard) on a
Zotac 890GXITX.
Signed-off-by: Julien Ducourthial <jducourt@free.fr> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
With infinite gratitude to Eric Dumazet for allowing me to identify
the error.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hayes Wang <hayeswang@realtek.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An application may call connect() to disconnect a socket using an
address with family AF_UNSPEC. The L2TP IP sockets were not handling
this case when the socket is not bound and an attempt to connect()
using AF_UNSPEC in such cases would result in an oops. This patch
addresses the problem by protecting the sk_prot->disconnect() call
against trying to unhash the socket before it is bound.
The patch also adds more checks that the sockaddr supplied to bind()
and connect() calls is valid.
Since commit ad0081e43a
"ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed"
the fragment of packets is incorrect.
because tunnel mode needs IPsec headers and trailer for all fragments,
while on transport mode it is sufficient to add the headers to the
first fragment and the trailer to the last.
so modify mtu and maxfraglen base on ipsec mode and if fragment is first
or last.
with my test,it work well(every fragment's size is the mtu)
and does not trigger slow fragment path.
Changes from v1:
though optimization, mtu_prev and maxfraglen_prev can be delete.
replace xfrm mode codes with dst_entry's new frag DST_XFRM_TUNNEL.
add fuction ip6_append_data_mtu to make codes clearer.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
bridge: set fake_rtable's dst to NULL to avoid kernel Oops
when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.
v4 reformat, change br_drop_fake_rtable(skb) to {}
v3 enrich commit header
v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.
[ Use "do { } while (0)" for nop br_drop_fake_rtable()
implementation -DaveM ]
Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Peter Huang <peter.huangpeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
<3>[23898.789643] BUG: sleeping function called from invalid context at
/data/buildbot/workdir/ics/hardware/intel/linux-2.6/arch/x86/mm/fault.c:1103
<3>[23898.862215] in_atomic(): 0, irqs_disabled(): 0, pid: 10526, name:
Thread-6683
<4>[23898.967805] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.258526] Pid: 10526, comm: Thread-6683 Tainted: G W 3.0.8-137685-ge7742f9 #1
<4>[23899.357404] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.904225] Call Trace:
<4>[23899.989209] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.000416] [<c1238c2a>] __might_sleep+0x10a/0x110
<4>[23900.007357] [<c1228021>] do_page_fault+0xd1/0x3c0
<4>[23900.013764] [<c18e9ba9>] ? restore_all+0xf/0xf
<4>[23900.024024] [<c17c007b>] ? napi_complete+0x8b/0x690
<4>[23900.029297] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.123739] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.128955] [<c18ea0c3>] error_code+0x5f/0x64
<4>[23900.133466] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.138450] [<c17f6298>] ? __ip_route_output_key+0x698/0x7c0
<4>[23900.144312] [<c17f5f8d>] ? __ip_route_output_key+0x38d/0x7c0
<4>[23900.150730] [<c17f63df>] ip_route_output_flow+0x1f/0x60
<4>[23900.156261] [<c181de58>] ip4_datagram_connect+0x188/0x2b0
<4>[23900.161960] [<c18e981f>] ? _raw_spin_unlock_bh+0x1f/0x30
<4>[23900.167834] [<c18298d6>] inet_dgram_connect+0x36/0x80
<4>[23900.173224] [<c14f9e88>] ? _copy_from_user+0x48/0x140
<4>[23900.178817] [<c17ab9da>] sys_connect+0x9a/0xd0
<4>[23900.183538] [<c132e93c>] ? alloc_file+0xdc/0x240
<4>[23900.189111] [<c123925d>] ? sub_preempt_count+0x3d/0x50
Function free_fib_info resets nexthop_nh->nh_dev to NULL before releasing
fi. Other cpu might be accessing fi. Fixing it by delaying the releasing.
With the patch, we ran MTBF testing on Android mobile for 12 hours
and didn't trigger the issue.
Thank Eric for very detailed review/checking the issue.
Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com> Signed-off-by: Kun Jiang <kunx.jiang@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Enabling FBC is causing the BLT ring to run between 10-100x slower than
normal and frequently lockup. The interim solution is disable FBC once
more until we know why.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to
the blacklist of btusb module and add it to the ath3k module to properly
load the firmware in Kernel 3.3.4
The device is integrated in e.g. some Acer Aspire 7750G.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
I was trying to backport the following commit to RHEL-6
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.
Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads
correctly.
Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: João Paulo Rechi Vita <jprvita@openbossa.org> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / karo-tx-linux.git / log