Johannes Berg [Wed, 5 May 2010 13:25:02 +0000 (15:25 +0200)]
cfg80211/mac80211: better channel handling
Currently (all tested with hwsim) you can do stupid
things like setting up an AP on a certain channel,
then adding another virtual interface and making
that associate on another channel -- this will make
the beaconing to move channel but obviously without
the necessary IEs data update.
In order to improve this situation, first make the
configuration APIs (cfg80211 and nl80211) aware of
multi-channel operation -- we'll eventually need
that in the future anyway. There's one userland API
change and one API addition. The API change is that
now SET_WIPHY must be called with virtual interface
index rather than only wiphy index in order to take
effect for that interface -- luckily all current
users (hostapd) do that. For monitor interfaces, the
old setting is preserved, but monitors are always
slaved to other devices anyway so no guarantees.
The second userland API change is the introduction
of a per virtual interface SET_CHANNEL command, that
hostapd should use going forward to make it easier
to understand what's going on (it can automatically
detect a kernel with this command).
Other than mac80211, no existing cfg80211 drivers
are affected by this change because they only allow
a single virtual interface.
mac80211, however, now needs to be aware that the
channel settings are per interface now, and needs
to disallow (for now) real multi-channel operation,
which is another important part of this patch.
One of the immediate benefits is that you can now
start hostapd to operate on a hardware that already
has a connection on another virtual interface, as
long as you specify the same channel.
Note that two things are left unhandled (this is an
improvement -- not a complete fix):
* different HT/no-HT modes
currently you could start an HT AP and then
connect to a non-HT network on the same channel
which would configure the hardware for no HT;
that can be fixed fairly easily
* CSA
An AP we're connected to on a virtual interface
might indicate switching channels, and in that
case we would follow it, regardless of how many
other interfaces are operating; this requires
more effort to fix but is pretty rare after all
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 May 2010 07:44:02 +0000 (09:44 +0200)]
mac80211: fix BSS info reconfiguration
When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.
Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Tue, 4 May 2010 21:54:41 +0000 (22:54 +0100)]
orinoco: refactor xmit path
... so orinoco_usb can share some common functionality.
Handle 802.2 encapsulation and MIC calculation in that function.
The 802.3 header is prepended to the SKB. The calculated MIC is written
to a specified buffer. Also modify the transmit control word that will
be passed onto the hardware to specify whether the MIC is present, and
the key used.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 4 May 2010 07:58:57 +0000 (09:58 +0200)]
ath9k: fix another source of corrupt frames
Atheros hardware supports receiving frames that span multiple
descriptors and buffers. In this case, the rx status of every
descriptor except for the last one is invalid and may contain random
data. Because the driver does not support this, it needs to drop such
frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the incomplete AMPDU implementation in ar9170usb.
The code in question is:
* too big and complex (more than 550 SLOC.)
This is enough to qualify for a new separate code file!
* unbalanced quantity & quality
over-engineered areas like:
* xmit scheduling and queuing frames for multiple HT peers
* redundant frame sorting
are confronted by gaping holes:
* accurate transmission feedback
* firmware error-handling and device reset
* HT rate control algorithm
* error-prone
Since its inclusion, hardly anything was done to fix
any of the outlined flaws from the initial commit message.
=> This also indicates poor maintainability.
* relies heavily on several spinlocks.
As a result of this shortcomings, the code is slow and does not
even support the most basic 11n requirement: HT station mode.
Therefore, I request to purge my heap of **** from the kernel:
"ar9170: implement transmit aggregation".
The next item on the agenda is: (re-)start from scratch with
an adequate design to accommodate the special requirements
and features of the available frameworks and tools.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inspection of the Ralink vendor driver shows that the TX_BAND_CFG register
and BBP register 3 are about HT40- indication, not about HT40+ indication.
Inverse the meaning of these fields in the code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Mon, 3 May 2010 17:55:07 +0000 (10:55 -0700)]
iwlwifi: recalculate average tpt if not current
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: rt2x00: rt2800usb: be in sync with latest windows drivers.
0x07d1,0x3c17 D-Link Wireless N 150 USB Adapter DWA-125
0x1b75,0x3071 Ovislink Airlive WN-301USB
0x1d4d,0x0011 Pegatron Ralink RT3072 802.11b/g/n Wireless Lan USB Device
0x083a,0xf511 Arcadyan 802.11 USB Wireless LAN Card
0x13d3,0x3322 AzureWave 802.11 n/g/b USB Wireless LAN Card
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 3 May 2010 06:49:48 +0000 (08:49 +0200)]
mac80211: improve IBSS scanning
When IBSS is fixed to a frequency, it can still
scan to try to find the right BSSID. This makes
sense if the BSSID isn't also fixed, but it need
not scan all channels -- just one is sufficient.
Make it do that by moving the scan setup code to
ieee80211_request_internal_scan() and include
a channel variable setting.
Note that this can be further improved to start
the IBSS right away if both frequency and BSSID
are fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 1 May 2010 16:53:51 +0000 (18:53 +0200)]
mac80211: allow controlling aggregation manually
This allows enabling TX and disabling both TX and
RX aggregation sessions manually in debugfs. It is
very useful for debugging session initiation and
teardown problems since with this you don't have
to force a lot of traffic to get aggregation and
thus have less data to analyse.
Also, to debug mac80211 code itself, make hwsim
"support" aggregation sessions. It will still just
transfer the frame, but go through the setup and
teardown handshakes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Sat, 1 May 2010 13:05:41 +0000 (14:05 +0100)]
orinoco: add orinoco_usb driver
This driver uses the core orinoco modules for the bulk of
the functionality. The low level hermes routines (for local bus
cards) are replaced, the driver supplies its own ndo_xmit_start
function, and locking is done with the _bh variant.
Some recent functionality is not available to the USB cards yet
(firmware loading and WPA).
Out-of-tree driver originally written by Manuel Estrada Sainz.
Thanks to Mark Davis for supplying hardware to test the updates.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Sat, 1 May 2010 13:05:40 +0000 (14:05 +0100)]
orinoco: encapsulate driver locking
Local bus and USB drivers will need to do locking differently.
The original orinoco_usb patches had a boolean variable controlling
whether spin_lock_bh was used, or irq based locking. This version
provides wrappers for the lock functions and the drivers specify the
functions pointers needed.
This will introduce a performance penalty, but I'm not expecting it to
be noticable.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Sat, 1 May 2010 13:05:39 +0000 (14:05 +0100)]
orinoco: allow driver to specify netdev_ops
Allow the main drivers to specify a custom version of the net_device_ops
structure. This is required by orinoco_usb to supply a separate transmit
function.
Export existing net_device_ops callbacks so that the drivers can reuse
some of the existing code.
Signed-off-by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 30 Apr 2010 11:48:36 +0000 (13:48 +0200)]
mac80211: fix ieee80211_find_sta[_by_hw]
Both of these functions can currently return
a station pointer that, to the driver, is
invalid (in IBSS mode only) because adding
the station failed. Check for that, and also
make ieee80211_find_sta() properly use the
per interface station search.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwl: cleanup: remove unneeded error handling" missed the one in
if_sdio_debugfs_init().
I don't think we even need to check -ENODEV ourselves because if
DEBUG_FS is not compiled in, all the debugfs utility functions will
become no-op.
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Tue, 20 Apr 2010 01:49:40 +0000 (18:49 -0700)]
iwlwifi: set hw parameters based on device type
Separate the hw_set_hw_params() function to per device based; different
devices can have different hardware parameters set, when separate the
function based on device type can avoid mistakes, give more flexibilities and
easier to read.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Daniel Halperin [Sun, 18 Apr 2010 16:27:58 +0000 (09:27 -0700)]
iwlwifi: set AMPDU status variables correctly
The TX status code is currently abusing the ampdu_ack_map field (a bitmap) to
count the number of successfully received frames. The comments in mac80211.h
show there are actually three different, relevant variables, of which we are
currently using two, both incorrectly. Fix this by making
- ampdu_ack_len -> the number of ACKed frames (i.e. successes)
- ampdu_ack_map -> the bitmap
- ampdu_len -> the total number of frames sent (i.e., attempts)
to match the header file (and verified with ath9k's usage) and updating Intel's
RS code to match.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When starting an aggregation session, the swq_id is generated in function
iwl_virtual_agg_queue_num() where the first parameter is supposed to be
the Access Class, but it used the tx fifo ID instead. This means the AC
value stored in swq_id is incorrect. To test this, look at the tx_queue
file in debugfs while transmitting Best Effort flow (ac=2), it shows:
hwq 10: read=0 write=0 stop=0 swq_id=0xa9 (ac 1/hwq 10)
After this fix, it will show:
hwq 10: read=0 write=0 stop=0 swq_id=0xaa (ac 2/hwq 10)
We removed resetting of PCI_RETRY_TIMEOUT register
in merge of suspend resume work.
'Suspend and resume' resets the PCI configuration space, so we
have to disable the RETRY_TIMEOUT register again here.
Wey-Yi Guy [Tue, 13 Apr 2010 18:28:52 +0000 (11:28 -0700)]
iwlwifi: remove get_stats callback function
The low level transmission function is performed at uCode layer
for all the "agn" NICs, there is no statistics information available
for mac80211 get_stats() call. Remove the callback function to
avoid misleading information that returned success when indeed it is not
supported. Now return "not supported".
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Merge branch 'wireless-2.6' into wireless-next-2.6
Patch "iwlwifi: work around passive scan issue" was merged into
wireless-2.6, but touched a lot of code since modified (and moved)
in wireless-next-2.6. This caused some conflicts.
Johannes Berg [Fri, 30 Apr 2010 21:42:15 +0000 (14:42 -0700)]
iwlwifi: work around passive scan issue
Some firmware versions don't behave properly when
passive scanning is requested on radar channels
without enabling active scanning on receiving a
good frame. Work around that issue by asking the
firmware to only enable the active scanning after
receiving a huge number of good frames, a number
that can never be reached during our dwell time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 19:34:01 +0000 (21:34 +0200)]
mac80211: tell driver about IBSS merge
My previous patch "mac80211: notify driver about
IBSS status" left a problem -- when we merge with
a new BSSID, we never tell the driver that we left
the old one. Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 28 Apr 2010 09:01:15 +0000 (11:01 +0200)]
iwl: cleanup: remove unneeded error handling
This is just a cleanup and doesn't change how the code works.
debugfs_create_dir() and debugfs_create_file() return an error pointer
(-ENODEV) if CONFIG_DEBUG_FS is not enabled, otherwise if an error occurs
they return NULL. This is how they are implemented and what it says in
the DebugFS documentation. DebugFS can not be compiled as a module.
As a result, we only need to check for error pointers and particularly
-ENODEV one time to know that DebugFS is enabled. This patch keeps the
first check for error pointers and removes the rest.
The other reason for this patch, is that it silences some Smatch warnings.
Smatch sees the condition "(result != -ENODEV)" and assumes that it's
possible for "result" to equal -ENODEV. If it were possible it would lead
to an error pointer dereference. But since it's not, we can just remove
the check.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rfcsr and bbp init code for SoC devices to match with the
latest Ralink driver.
To have better control over which values are used for the register
initialization create a new function rt2800_is_305x_soc which checks
for SoC interface type, the correct RT chipset and the correct RF
chipset. This is based on the assumption that all rt305x SoC devices
use a rt2872 and rf3020/rf3021/rf3022.
In case an unknown RF chipset is found on a SoC device with a rt2872
don't treat it as rt305x and just print a message.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
A couple of sparse warnings in some rate settings (missing cpu_to_le32) were
fixed. Changed the conf_sg_settings struct from le to native endianess. The
values are converted to le when copying them to the acx command instead.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver had a join command without keep-alive restart procedures in the
channel changing code. After associated scans, the mac80211 does re-set the
current channel, causing the join to occur. This would stop the hardware
keep alive.
To make the joins safer in this respect, this patch adds a join function that
does the hardware-keep-alive magic along the join. This is now invoked in the
above mentioned scenario, and also other scenarios.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In testing I noticed that the wl1271 commands fall into two categories. In the
first category are "fast" commands, these mostly take only 0 or 1 polls to
complete, but occasionally upto 50 (giving a 0.5ms execution time.) In the
second category, the command completion takes well more than 0.5ms (from
1.5ms upwards.)
This patch fixes command polling such that it is optimal for the fast commands,
but also allows sleep for the longer ones.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently whenever rts thresold is set, every packet will use RTS
protection no matter its size exceeds the threshold or not. This is
due to a bug in the rts threshold check.
if (len > tx->local->hw.wiphy->rts_threshold) {
txrc.rts = rts = true;
}
Basically it is comparing an int (len) and a u32 (rts_threshold),
and the variable len is assigned as:
len = min_t(int, tx->skb->len + FCS_LEN,
tx->local->hw.wiphy->frag_threshold);
However, when frag_threshold is "-1", len is always "-1", which is
0xffffffff therefore rts is always set to true.
CC: stable@kernel.org Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 27 Apr 2010 09:59:34 +0000 (11:59 +0200)]
mac80211: give virtual interface to hw_scan
When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the mac80211 is choosing dynamic ps timeouts based on the ps-qos
network latency configuration, configure a default value of -1 as the dynamic
ps timeout in cfg80211. This value allows the mac80211 to determine the value
to be used.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Determine dynamic PS timeout based on ps-qos network latency
Determine the dynamic PS timeout based on the configured ps-qos network
latency. For backwards wext compatibility, allow the dynamic PS timeout
configured by the cfg80211 to overrule the automatically determined value.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Avoid corrupt frames being forwarded to mac80211.
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Cc: stable@kernel.org Reported-by: Johan Hovold <johan.hovold@lundinova.se> Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX interrupt mitigation reduces the number of interrupts
by addressing several interrupt actions (AR_IMR_TXOK,
AR_IMR_TXDESC) all in one interrupt so when enabling
it discard setting the other interrupts.
Without this TX interrupt mitigation would actually
increase the number of interrupts two-fold. We still
leave TX interrupt mitigation disabled as it is still
being tested.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 26 Apr 2010 19:04:40 +0000 (15:04 -0400)]
ath9k_hw: fix noisefloor timeout handling on AR9003
When the noisefloor calibration times out, do not load -50 into
the registers, since this might cause rx issues. Instead, leave
enough time for the noise floor calibration to complete until
the next check.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 26 Apr 2010 19:04:37 +0000 (15:04 -0400)]
ath9k_hw: use the configured power limit for AR9003
Since the new AR9003 EEPROM code does tune the card for the configured
tx power level, we need to fill in the correct power limits in the TPC
part of the DMA descriptor.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable TX IQ calibration, it was prematurely enabled in
previous versions.
Cc: Paul Shaw <Paul.Shaw@Atheros.com> Cc: Thomas Hammel <Thomas.Hammel@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 26 Apr 2010 19:04:29 +0000 (15:04 -0400)]
ath9k_hw: update initvals for AR9003
This synchs up the initvals to the values used on the
Atheros HAL for AR9003. This specific change adds support
for a new high power module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 26 Apr 2010 22:26:34 +0000 (00:26 +0200)]
mac80211: fix handling of 4-address-mode in ieee80211_change_iface
A misplaced interface type check bails out too early if the interface
is not in monitor mode. This patch moves it to the right place, so that
it only covers changes to the monitor flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of validation and processing in the RX IRQ handler
can be moved to the RX tasklet. The IRQ handler is
already heavy, with the memory allocation for handling
stream mode. Also, a memcpy of 40 bytes for every packet
can be avoided in the handler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Steve deRosier [Sun, 25 Apr 2010 21:40:46 +0000 (14:40 -0700)]
libertastf: add configurable debug messages
Add the same type of configurable debug messages to libertas_tf as
already exist in the libertas driver. This has facilitated creation
of a interface specification and will facilitate future development
of this driver.
Signed-off-by: Steve deRosier <steve@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 26 Apr 2010 08:18:08 +0000 (10:18 +0200)]
rt2x00: fix typo in rt2800.h
Fix a typo in a comment in rt2800.h. Instead of replacing the wrong
hexvalue (0x171c) with the correct one (0x1718) just use the appropriate
readable define.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 23 Apr 2010 18:17:21 +0000 (13:17 -0500)]
ssb: Make bus registration failure not be silent
In kernel Bugzilla #15825, a case where routine ssb_bus_pcibus_register()
fails silently is reported. The cause for the failure is still being
investigated; however, the diagnosis would be easier if the failure
had been reported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 23 Apr 2010 13:54:43 +0000 (15:54 +0200)]
rt2x00: rt2800: use tx_power2 in rt2800_config_channel_rf3xxx
Get closer to what the ralink driver does by setting the rf register 13
to tx_power2 during channel switch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 23 Apr 2010 13:05:29 +0000 (15:05 +0200)]
rt2x00: rt2800lib: disable HT40 for now as it causes reception problems
Disable HT40 support for now as it causes rx problems with HT40 capable
11n APs (when mac80211 enables HT40, rx is completely disfunctional).
Once the rt2800 HT code is capable of using HT40 we should enable the
flag again.
I only tested this patch with a rt305x SoC device, nevertheless the
patch disables HT40 also on PCI and USB rt2800 devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
All commands to the target are disabled when the device
is unplugged, but a normal module unload has to be
differentiated from this case, as we could still receive
data in the RX endpoint. Fix this by checking if the
device is attached or not.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log