The parallel-port code of the drivers used a stack allocated
control-request buffer for asynchronous (and possibly deferred) control
requests. This not only violates the no-DMA-from-stack requirement but
could also lead to corrupt control requests being submitted.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bug in device-type detection on big-endian machines originally
introduced by commit 0eafe4de ("USB: serial: mos7840: add support for
MCS7810 devices") which always matched on little-endian product ids.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix endianess bugs in firmware handling introduced by commits cb7a7c6a
("ti_usb_3410_5052: add Multi-Tech modem support") and 05a3d905
("ti_usb_3410_5052: support alternate firmware") which made the driver
use the wrong firmware for certain devices on big-endian machines.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is similar to the race Linus had reported, but in this case
it's an older bug: nl80211_prepare_wdev_dump() uses the wiphy
index in cb->args[0] as it is and thus parses the message over
and over again instead of just once because 0 is the first valid
wiphy index. Similar code in nl80211_testmode_dump() correctly
offsets the wiphy_index by 1, do that here as well.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've added a fake mute control (setting the amp volume to zero) for
CX5051 at commit [3868137e: ALSA: hda - Add a fake mute feature], but
this feature was overlooked in the generic parser implementation. Now
the driver lacks of mute controls on these codecs.
The fix is just to check both AC_AMPCAP_MUTE and AC_AMPCAP_MIN_MUTE
bits in each place checking the amp capabilities.
Add the volume control quirk for avoiding the kernel warning
for the Logitech HD Webcam C525
as in the similar commit 36691e1be6ec551eef4a5225f126a281f8c051c2
for the Logitech HD Webcam C310.
Reported-by: Maksim Boyko <maksim.a.boyko@gmail.com> Tested-by: Maksim Boyko <maksim.a.boyko@gmail.com> Signed-off-by: Maksim Boyko <maksim.a.boyko@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra30 I2S driver was writing the AHUB interface parameters to the
playback path register rather than the capture path register. This
caused the capture parameters not to be configured at all, so if
capturing using non-HW-default parameters (e.g. 16-bit stereo rather
than 8-bit mono) the audio would be corrupted.
With this fixed, audio capture from an analog microphone works correctly
on the Cardhu board.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Beep Volume Min/Max was backwards.
Change to SOC_SONGLE_SX_TLV for correct volume representation
Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_first_entry() will always return a valid pointer, even if the list is
empty. So the check whether path is NULL will always be false. So we end up
calling dapm_create_or_share_mixmux_kcontrol() with a path struct that points
right in the middle of the widget struct and by trying to modify the path the
widgets memory will become corrupted. Fix this by using list_emtpy() to check if
the widget doesn't have any paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a P2P GO interface goes down, cfg80211 doesn't properly
tear it down, leading to warnings later. Add the GO interface
type to the enumeration to tear it down like AP interfaces.
Otherwise, we leave it pending and mac80211's state can get
very confused, leading to warnings later.
Reported-by: Ilan Peer <ilan.peer@intel.com> Tested-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dumping generic netlink families, only the first dump call
is locked with genl_lock(), which protects the list of families,
and thus subsequent calls can access the data without locking,
racing against family addition/removal. This can cause a crash.
Fix it - the locking needs to be conditional because the first
time around it's already locked.
A similar bug was reported to me on an old kernel (3.4.47) but
the exact scenario that happened there is no longer possible,
on those kernels the first round wasn't locked either. Looking
at the current code I found the race described above, which had
also existed on the old kernel.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix possibly wrong memcpy() bytes length since some CAN records received from
PCAN-USB could define a DLC field in range [9..15].
In that case, the real DLC value MUST be used to move forward the record pointer
but, only 8 bytes max. MUST be copied into the data field of the struct
can_frame object of the skb given to the network core.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.
Reported-by: Chris Wright <chrisw@sous-sol.org> Tested-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "3d9646d mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop. When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely. Replace goto with
break and carry on. This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking. Thanks to Derek Atkins
as an extra pair of debugging eyes.
Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.
Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.
Work around this by ignoring the HT primary channel information in
beacons if we're already connected.
Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.
Acked-by: Andy Isaacson <adi@hexapodia.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using rfkill switch can make firmware unstable, what cause various
Microcode errors and kernel warnings. Reseting firmware just after
rfkill off (radio on) helped with that.
If device was put into a sleep and system was restarted or module
reloaded, we have to wake device up before sending other commands.
Otherwise it will fail to start with Microcode error.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not saving PAR is an unfortunate oversight. If the guest performs
an AT* operation and gets scheduled out before reading the result
of the translation from PAR, it could become corrupted by another
guest or the host.
Saving this register is made slightly more complicated as KVM also
uses it on the permission fault handling path, leading to an ugly
"stash and restore" sequence. Fortunately, this is already a slow
path so we don't really care. Also, Linux doesn't do any AT*
operation, so Linux guests are not impacted by this bug.
[ Slightly tweaked to use an even register as first operand to ldrd
and strd operations in interrupts_head.S - Christoffer ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a race between elevator switching and normal io operation.
Because the allocation of struct elevator_queue and struct elevator_data
don't in a atomic operation.So there are have chance to use NULL
->elevator_data.
For example:
Thread A: Thread B
blk_queu_bio elevator_switch
spin_lock_irq(q->queue_block) elevator_alloc
elv_merge elevator_init_fn
Because call elevator_alloc, it can't hold queue_lock and the
->elevator_data is NULL.So at the same time, threadA call elv_merge and
nedd some info of elevator_data.So the crash happened.
Move the elevator_alloc into func elevator_init_fn, it make the
operations in a atomic operation.
Using the follow method can easy reproduce this bug
1:dd if=/dev/sdb of=/dev/null
2:while true;do echo noop > scheduler;echo deadline > scheduler;done
We typically update a task_group's shares within the dequeue/enqueue
path. However, continuously running tasks sharing a CPU are not
subject to these updates as they are only put/picked. Unfortunately,
when we reverted f269ae046 (in 17bc14b7), we lost the augmenting
periodic update that was supposed to account for this; resulting in a
potential loss of fairness.
To fix this, re-introduce the explicit update in
update_cfs_rq_blocked_load() [called via entity_tick()].
Reported-by: Max Hailperin <max@gustavus.edu> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Reviewed-by: Paul Turner <pjt@google.com> Link: http://lkml.kernel.org/n/tip-9545m3apw5d93ubyrotrj31y@git.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently we met quite a lot of random kernel panic issues after enabling
CONFIG_PROC_PAGE_MONITOR. After debuggind we found this has something
to do with following bug in pagemap:
pos is number of PM_ENTRY_BYTES in buffer, but len is the size of
buffer, it is a mistake to compare pos and len in add_page_map() for
checking buffer is full or not, and this can lead to buffer overflow and
random kernel panic issue.
Correct len to be total number of PM_ENTRY_BYTES in buffer.
When the stack is set to unlimited, the bottomup direction is used for
mmap-ings but the mmap_base is not used and thus effectively renders
ASLR for mmapings along with PIE useless.
Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Michel Lespinasse <walken@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: Adrian Sendroiu <molecula2788@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix inadvertent breakage in the clone syscall ABI for Microblaze that
was introduced in commit f3268edbe6fe ("microblaze: switch to generic
fork/vfork/clone").
The Microblaze syscall ABI for clone takes the parent tid address in the
4th argument; the third argument slot is used for the stack size. The
incorrectly-used CLONE_BACKWARDS type assigned parent tid to the 3rd
slot.
This commit restores the original ABI so that existing userspace libc
code will work correctly.
All kernel versions from v3.8-rc1 were affected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct memcg_cache_params has a union. Different parts of this union
are used for root and non-root caches. A part with destroying work is
used only for non-root caches.
I fixed the same problem in another place v3.9-rc1-16204-gf101a94, but
didn't notice this one.
John McCalpin reports that the "drs_data" and "ncb_data" QPI
uncore events are missing the "extra bit" and always return zero
values unless the bit is properly set.
More details from him:
According to the Xeon E5-2600 Product Family Uncore Performance
Monitoring Guide, Table 2-94, about 1/2 of the QPI Link Layer events
(including the ones that "perf" calls "drs_data" and "ncb_data") require
that the "extra bit" be set.
This was confusing for a while -- a note at the bottom of page 94 says
that the "extra bit" is bit 16 of the control register.
Unfortunately, Table 2-86 clearly says that bit 16 is reserved and must
be zero. Looking around a bit, I found that bit 21 appears to be the
correct "extra bit", and further investigation shows that "perf" actually
agrees with me:
[root@c560-003.stampede]# cat /sys/bus/event_source/devices/uncore_qpi_0/format/event
config:0-7,21
So the command
# perf -e "uncore_qpi_0/event=drs_data/"
Is the same as
# perf -e "uncore_qpi_0/event=0x02,umask=0x08/"
While it should be
# perf -e "uncore_qpi_0/event=0x102,umask=0x08/"
I confirmed that this last version gives results that agree with the
amount of data that I expected the STREAM benchmark to move across the QPI
link in the second (cross-chip) test of the original script.
Reported-by: John McCalpin <mccalpin@tacc.utexas.edu> Signed-off-by: Vince Weaver <vincent.weaver@maine.edu> Cc: zheng.z.yan@intel.com Cc: Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: Paul Mackerras <paulus@samba.org> Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1308021037280.26119@vincent-weaver-1.um.maine.edu Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENERIC_PCI_IOMAP does not depend on CONFIG_PCI so move
it to the CONFIG_MIPS symbol so it's always selected for MIPS.
This fixes the missing pci_iomap declaration for MIPS.
Moreover, the pci_iounmap function was not defined in the
io.h header file if the CONFIG_PCI symbol is not set,
but it should since MIPS is not using CONFIG_GENERIC_IOMAP.
This fixes the following problem on a allyesconfig:
drivers/net/ethernet/3com/3c59x.c:1031:2: error: implicit declaration of
function 'pci_iomap' [-Werror=implicit-function-declaration]
drivers/net/ethernet/3com/3c59x.c:1044:3: error: implicit declaration of
function 'pci_iounmap' [-Werror=implicit-function-declaration]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/5478/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The omap2 nand device driver calls into the the elm code, which can
be a loadable module, and in that case it cannot be built-in itself.
I can see no reason why the omap2 driver cannot also be a module,
so let's make the option "tristate" in Kconfig to fix this allmodconfig
build error:
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ rebased for 3.10 and dropped the drivers/gpu/drm/radeon/cik.c
bit as it's 3.11 specific code / tmb ] Signed-off-by: Thomas Backlund <tmb@mageia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
v2: rebased for 3.10-stable tree
Signed-off-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
v2: rebased on 3.10-stable tree
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since remove_proc_entry() started to wait for IO in progress (i.e.
since 2007 or so), the locking in fs/reiserfs/proc.c became wrong;
if procfs read happens between the moment when umount() locks the
victim superblock and removal of /proc/fs/reiserfs/<device>/*,
we'll get a deadlock - read will wait for s_umount (in sget(),
called by r_start()), while umount will wait in remove_proc_entry()
for that read to finish, holding s_umount all along.
Fortunately, the same change allows a much simpler race avoidance -
all we need to do is remove the procfs entries in the very beginning
of reiserfs ->kill_sb(); that'll guarantee that pointer to superblock
will remain valid for the duration for procfs IO, so we don't need
sget() to keep the sucker alive. As the matter of fact, we can
get rid of the home-grown iterator completely, and use single_open()
instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. it wrongly assumes that !list_empty(d_subdirs) means that this
dir should be removed.
This is not that bad by itself, but:
2. if d_subdirs does not becomes empty after __debugfs_remove()
it gives up and silently fails, it doesn't even try to remove
other entries.
However ->d_subdirs can be non-empty because it still has the
already deleted !debugfs_positive() entries.
3. simple_release_fs() is called even if __debugfs_remove() fails.
Suppose we have
dir1/
dir2/
file2
file1
and someone opens dir1/dir2/file2.
Now, debugfs_remove_recursive(dir1/dir2) succeeds, and dir1/dir2 goes
away.
But debugfs_remove_recursive(dir1) silently fails and doesn't remove
this directory. Because it tries to delete (the already deleted)
dir1/dir2/file2 again and then fails due to "Avoid infinite loop"
logic.
And after that it is not possible to create another probe entry.
With this patch debugfs_remove_recursive() skips !debugfs_positive()
files although this is not strictly needed. The most important change
is that it does not try to make ->d_subdirs empty, it simply scans
the whole list(s) recursively and removes as much as possible.
The USB hub driver's event handler contains a check to catch SuperSpeed
devices that transitioned into the SS.Inactive state and tries to fix
them with a reset. It decides whether to do a plain hub port reset or
call the usb_reset_device() function based on whether there was a device
attached to the port.
However, there are device/hub combinations (found with a JetFlash
Transcend mass storage stick (8564:1000) on the root hub of an Intel
LynxPoint PCH) which can transition to the SS.Inactive state on
disconnect (and stay there long enough for the host to notice). In this
case, above-mentioned reset check will call usb_reset_device() on the
stale device data structure. The kernel will send pointless LPM control
messages to the no longer connected device address and can even cause
several 5 second khubd stalls on some (buggy?) host controllers, before
finally accepting the device's fate amongst a flurry of error messages.
This patch makes the choice of reset dependent on the port status that
has just been read from the hub in addition to the existence of an
in-kernel data structure for the device, and only proceeds with the more
extensive reset if both are valid.
Signed-off-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David reported that commit c2b93e06 (cifs: only set ops for inodes in
I_NEW state) caused a regression with mfsymlinks. Prior to that patch,
if a mfsymlink dentry was instantiated at readdir time, the inode would
get a new set of ops when it was revalidated. After that patch, this
did not occur.
This patch addresses this by simply skipping instantiating dentries in
the readdir codepath when we know that they will need to be immediately
revalidated. The next attempt to use that dentry will cause a new lookup
to occur (which is basically what we want to happen anyway).
Reported-and-Tested-by: David McBride <dwm37@cam.ac.uk> Cc: "Stefan (metze) Metzmacher" <metze@samba.org> Cc: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For cifs_set_cifscreds() in "fs/cifs/connect.c", 'desc' buffer length
is 'CIFSCREDS_DESC_SIZE' (56 is less than 256), and 'ses->domainName'
length may be "255 + '\0'".
The related sprintf() may cause memory overflow, so need extend related
buffer enough to hold all things.
It is also necessary to be sure of 'ses->domainName' must be less than
256, and define the related macro instead of hard code number '256'.
Signed-off-by: Chen Gang <gang.chen@asianux.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Reviewed-by: Scott Lovenberg <scott.lovenberg@gmail.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously we weren't swapping only some of the extent_status LRU
fields during the processing of the EXT4_IOC_SWAP_BOOT ioctl. The
much safer thing to do is to just completely flush the extent status
tree when doing the swap.
Commit 5688978 ("ext4: improve handling of conflicting mount options")
introduced incorrect messages shown while choosing wrong mount options.
First of all, both cases of incorrect mount options,
"data=journal,delalloc" and "data=journal,dioread_nolock" result in
the same error message.
Secondly, the problem above isn't solved for remount option: the
mismatched parameter is simply ignored. Moreover, ext4_msg states
that remount with options "data=journal,delalloc" succeeded, which is
not true.
To fix it up, I added a simple check after parse_options() call to
ensure that data=journal and delalloc/dioread_nolock parameters are
not present at the same time.
Signed-off-by: Piotr Sarna <p.sarna@partner.samsung.com> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 26092bf ("ext4: use a table-driven handler for mount options")
wrongly disallows the specifying the mount options nodelalloc and
data=journal simultaneously. This is incorrect; it should have only
disallowed the combination of delalloc and data=journal
simultaneously.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two audio dtos on radeon asics that you can
select between. Normally, dto0 is used for hdmi and
dto1 for DP, but it seems that the dto is somehow
tied to the encoders on DCE3 asics.
It takes an unsigned value. This happens not to blow up on 64-bit
architectures, but it does on 32-bit, causing
drm_calc_vbltimestamp_from_scanoutpos() to calculate totally bogus
timestamps for vblank events. Which in turn causes e.g. gnome-shell to
hang after a DPMS off cycle with current xf86-video-ati Git.
[airlied: regression introduced in drm: use monotonic time in drm_calc_vbltimestamp_from_scanoutpos]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59836 Tested-by: shui yangwei <yangweix.shui@intel.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a BO gets pinned the placement may get changed. If the memory is
mapped into user space and user space has already accessed the mapped
range the page tables are set up but now point to the wrong memory.
Set bo.mdev->dev_mapping in mgag200_bo_create() to make sure that
ttm_bo_unmap_virtual() called from ttm_bo_handle_move_mem() will take
care of this.
v2: Don't call ttm_bo_unmap_virtual() in mgag200_bo_pin(), fix comment.
This is a cirrus version of Egbert Eich's patch for mgag200.
Without bo.bdev->dev_mapping set, the ttm_bo_unmap_virtual_locked
called from ttm_bo_handle_move_mem returns with no effect. If any
application accessed the memory before it was moved, it will
access wrong memory next time. This causes crashes when changing
resolution down.
Signed-off-by: Michal Srb <msrb@suse.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port gets unplugged while a user is blocked on read(), -ENODEV is
returned. However, subsequent read()s returned 0, indicating there's no
host-side connection (but not indicating the device went away).
This also happened when a port was unplugged and the user didn't have
any blocking operation pending. If the user didn't monitor the SIGIO
signal, they won't have a chance to find out if the port went away.
Fix by returning -ENODEV on all read()s after the port gets unplugged.
write() already behaves this way.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SIGIO should be sent when a port gets unplugged. It should only be sent
to prcesses that have the port opened, and have asked for SIGIO to be
delivered. We were clearing out guest_connected before calling
send_sigio_to_port(), resulting in a sigio not getting sent to
processes.
Fix by setting guest_connected to false after invoking the sigio
function.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to keep the port's char device structs and the /sys entries
around till the last reference to the port was dropped. This is
actually unnecessary, and resulted in buggy behaviour:
1. Open port in guest
2. Hot-unplug port
3. Hot-plug a port with the same 'name' property as the unplugged one
This resulted in hot-plug being unsuccessful, as a port with the same
name already exists (even though it was unplugged).
This behaviour resulted in a warning message like this one:
Instead of relying on guest applications to release all references to
the ports, we should go ahead and unregister the port from all the core
layers. Any open/read calls on the port will then just return errors,
and an unplug/plug operation on the host will succeed as expected.
This also caused buggy behaviour in case of the device removal (not just
a port): when the device was removed (which means all ports on that
device are removed automatically as well), the ports with active
users would clean up only when the last references were dropped -- and
it would be too late then to be referencing char device pointers,
resulting in oopses:
Between open() being called and processed, the port can be unplugged.
Check if this happened, and bail out.
A simple test script to reproduce this is:
while true; do for i in $(seq 1 100); do echo $i > /dev/vport0p3; done; done;
This opens and closes the port a lot of times; unplugging the port while
this is happening triggers the bug.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a window between find_port_by_devt() returning a port and us
taking a kref on the port, where the port could get unplugged. Fix it
by taking the reference in find_port_by_devt() itself.
Problem reported and analyzed by Mateusz Guzik.
Reported-by: Mateusz Guzik <mguzik@redhat.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pipe_lock/unlock for splice_write to avoid oops by following competition:
(1) An application gets fds of a trace buffer, virtio-serial, pipe.
(2) The application does fork()
(3) The processes execute splice_read(trace buffer) and
splice_write(virtio-serial) via same pipe.
<parent> <child>
get fds of a trace buffer,
virtio-serial, pipe
|
fork()----------create--------+
| |
splice(read) | ---+
splice(write) | +-- no competition
| splice(read) |
| splice(write) ---+
| |
splice(read) |
splice(write) splice(read) ------ competition
| splice(write)
Two processes share a pipe_inode_info structure. If the child execute
splice(read) when the parent tries to execute splice(write), the
structure can be broken. Existing virtio-serial driver does not get
lock for the structure in splice_write, so this competition will induce
oops.
Quit from splice_write if pipe->nrbufs is 0 for avoiding oops in virtio-serial.
When an application was doing splice from a kernel buffer to virtio-serial on
a guest, the application received signal(SIGINT). This situation will normally
happen, but the kernel executed a kernel panic by oops as follows:
It seems to induce pagefault in sg_init_tabel() when pipe->nrbufs is equal to
zero. This may happen in a following situation:
(1) The application normally does splice(read) from a kernel buffer, then does
splice(write) to virtio-serial.
(2) The application receives SIGINT when is doing splice(read), so splice(read)
is failed by EINTR. However, the application does not finish the operation.
(3) The application tries to do splice(write) without pipe->nrbufs.
(4) The virtio-console driver tries to touch scatterlist structure sgl in
sg_init_table(), but the region is out of bound.
To avoid the case, a kernel should check whether pipe->nrbufs is empty or not
when splice_write is executed in the virtio-console driver.
V3: Add Reviewed-by lines and stable@ line in sign-off area.
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Amit Shah <amit.shah@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If rpcbind causes our connection to the AF_LOCAL socket to close after
we've registered a service, then we want to be careful about reconnecting
since the mount namespace may have changed.
By simply refusing to reconnect the AF_LOCAL socket in the case of
unregister, we avoid the need to somehow save the mount namespace. While
this may lead to some services not unregistering properly, it should
be safe.
There is no need for the kernel to time out the AF_LOCAL connection to
the rpcbind socket, and doing so is problematic because when it is
time to reconnect, our process may no longer be using the same mount
namespace.
Firstly, nlmclnt_setlockargs can be called from a reclaimer thread, in
which case we're in entirely the wrong namespace.
Secondly, commit 8aac62706adaaf0fab02c4327761561c8bda9448 (move
exit_task_namespaces() outside of exit_notify()) now means that
exit_task_work() is called after exit_task_namespaces(), which
triggers an Oops when we're freeing up the locks.
Fix this by ensuring that we initialise the nlm_host's rpc_client at mount
time, so that the cl_nodename field is initialised to the value of
utsname()->nodename that the net namespace uses. Then replace the
lockd callers of utsname()->nodename.
The ceph guys tripped over this bug where we were still holding onto the
original path that we used to copy the inode with when logging. This is based
on Chris's fix which was reported to fix the problem. We need to drop the paths
in two cases anyway so just move the drop up so that we don't have duplicate
code. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fixes 6fire not to use stack as URB transfer_buffer. URB buffers need to
be DMA-able, which stack is not. Furthermore, transfer_buffer should not be
allocated as part of larger device structure because DMA coherency issues and
patch fixes this issue too.
The driver used to assume that the streaming endpoint's wMaxPacketSize
value would be an indication of how much data the endpoint expects or
sends, and compute the number of packets per URB using this value.
However, the Focusrite Scarlett 2i4 declares a value of 1024 bytes,
while only about 88 or 44 bytes are be actually used. This discrepancy
would result in URBs with far too few packets, which would not work
correctly on the EHCI driver.
To get correct URBs, use wMaxPacketSize only as an upper limit on the
packet size.
Reported-by: James Stone <jamesmstone@gmail.com> Tested-by: James Stone <jamesmstone@gmail.com> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed two issues with changing the timestamp clock with trace_clock:
- The global buffer was reset on instance clock changes. Change this to pass
the correct per-instance buffer
- ftrace_now() is used to set buf->time_start in tracing_reset_online_cpus().
This was incorrect because ftrace_now() used the global buffer's clock to
return the current time. Change this to use buffer_ftrace_now() which
returns the current time for the correct per-instance buffer.
Also removed tracing_reset_current() because it is not used anywhere
Link: http://lkml.kernel.org/r/1375493777-17261-2-git-send-email-azl@google.com Signed-off-by: Alexander Z Lam <azl@google.com> Cc: Vaibhav Nagarnaik <vnagarnaik@google.com> Cc: David Sharp <dhsharp@google.com> Cc: Alexander Z Lam <lambchop468@gmail.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ring buffer is disabled and the irqsoff tracer records a trace it
will clear out its buffer and lose the data it had previously recorded.
Currently there's a callback when writing to the tracing_of file, but if
tracing is disabled via the function tracer trigger, it will not inform
the irqsoff tracer to stop recording.
By using the "mirror" flag (buffer_disabled) in the trace_array, that keeps
track of the status of the trace_array's buffer, it gives the irqsoff
tracer a fast way to know if it should record a new trace or not.
The flag may be a little behind the real state of the buffer, but it
should not affect the trace too much. It's more important for the irqsoff
tracer to be fast.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Releasing the free_buffer file in an instance causes the global buffer
to be stopped when TRACE_ITER_STOP_ON_FREE is enabled. Operate on the
correct buffer.
Link: http://lkml.kernel.org/r/1375493777-17261-1-git-send-email-azl@google.com Signed-off-by: Alexander Z Lam <azl@google.com> Cc: Vaibhav Nagarnaik <vnagarnaik@google.com> Cc: David Sharp <dhsharp@google.com> Cc: Alexander Z Lam <lambchop468@gmail.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tracing_read_pipe zeros all fields bellow "seq". The declaration contains
a comment about that, but it doesn't help.
The first field is "snapshot", it's true when current open file is
snapshot. Looks obvious, that it should not be zeroed.
The second field is "started". It was converted from cpumask_t to
cpumask_var_t (v2.6.28-4983-g4462344), in other words it was
converted from cpumask to pointer on cpumask.
Currently the reference on "started" memory is lost after the first read
from tracing_read_pipe and a proper object will never be freed.
The "started" is never dereferenced for trace_pipe, because trace_pipe
can't have the TRACE_FILE_ANNOTATE options.
The list of physical devices corresponding to an ACPI device
object is walked by acpi_system_wakeup_device_seq_show() and
physical_device_enable_wakeup() without taking that object's
physical_node_lock mutex. Since each of those functions may be
run at any time as a result of a user space action, the lack of
appropriate locking in them may lead to a kernel crash if that
happens during device hot-add or hot-remove involving the device
object in question.
Fix the issue by modifying acpi_system_wakeup_device_seq_show() and
physical_device_enable_wakeup() to use physical_node_lock as
appropriate.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This sysfs file was called ignore_nice_load earlier and commit 4d5dcc4 (cpufreq: governor: Implement per policy instances of
governors) changed its name to ignore_nice by mistake.
Lets get it renamed back to its original name.
Reported-by: Martin von Gagern <Martin.vGagern@gmx.net> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 42913c799 (MIPS: Loongson2: Use clk API instead of direct
dereferences) broke the cpufreq functionality on Loongson2 boards:
clk_set_rate() is called before the CPU frequency table is
initialized, and therefore will always fail.
Fix by moving the clk_set_rate() after the table initialization.
Tested on Lemote FuLoong mini-PC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the config structure pointer to the eeprom data pointer (data,
here eedata dereferenced) not the pointer to the pointer to
the eeprom data (eedata itself).
Signed-off-by: Alban Browaeys <prahal@yahoo.com> Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 835f2f5 ("staging: zcache: enable zcache to be built/loaded as
a module") introduced an incorrect handling of "zcache=" parameter.
Inside zcache_comp_init() function, zcache_comp_name variable is
checked for being empty. If not empty, the above variable is tested
for being compatible with Crypto API. Unfortunately, after that
function ends unconditionally (by the "goto out" directive) and returns:
- non-zero value if verification succeeded, wrongly indicating an error
- zero value if verification failed, falsely informing that function
zcache_comp_init() ended properly.
A solution to this problem is as following:
1. Move the "goto out" directive inside the "if (!ret)" statement
2. In case that crypto_has_comp() returned 0, change the value of ret
to non-zero before "goto out" to indicate an error.
This patch replaces an earlier one from Michal Hocko (based on report
from Cristian Rodriguez):
It also addressed the same issue but didn't fix the zcache_comp_init()
for case when the compressor data passed to "zcache=" option was invalid
or unsupported.
Signed-off-by: Piotr Sarna <p.sarna@partner.samsung.com>
[bzolnier: updated patch description] Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Cristian Rodriguez <crrodriguez@opensuse.org> Cc: Bob Liu <bob.liu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In adt7470_write_word_data(), which writes two bytes using
i2c_smbus_write_byte_data(), the return codes are incorrectly AND-ed
together when they should be OR-ed together.
The return code of i2c_smbus_write_byte_data() is zero for success.
The upshot is only the first byte was ever written to the hardware.
The 2nd byte was never written out.
I noticed that trying to set the fan speed limits was not working
correctly on my system. Setting the fan speed limits is the only
code that uses adt7470_write_word_data(). After making the change
the limit settings work and the alarms work also.
regmap.h requires linux/err.h if CONFIG_REGMAP is not defined. Without it I get
error.
CC drivers/media/platform/exynos4-is/fimc-reg.o
In file included from drivers/media/platform/exynos4-is/fimc-reg.c:14:0:
include/linux/regmap.h: In function ‘regmap_write’:
include/linux/regmap.h:525:10: error: ‘EINVAL’ undeclared (first use in this function)
include/linux/regmap.h:525:10: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regcache_sync_block_raw_flush() expects the address of the register after last
register that needs to be synced as its parameter. But the last call to
regcache_sync_block_raw_flush() in regcache_sync_block_raw() passes the address
of the last register in the block. This effectively always skips over the last
register in a block, even if it needs to be synced. In order to fix it increase
the address by one register.
The issue was introduced in commit 75a5f89 ("regmap: cache: Write consecutive
registers in a single block write").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we try to allocate an inode, and there is a race between two
CPU's trying to grab the same inode, _and_ this inode is the last free
inode in the block group, make sure the group number is bumped before
we continue searching the rest of the block groups. Otherwise, we end
up searching the current block group twice, and we end up skipping
searching the last block group. So in the unlikely situation where
almost all of the inodes are allocated, it's possible that we will
return ENOSPC even though there might be free inodes in that last
block group.
If a transaction is rolled back, the Target Address Register (TAR), Processor
Priority Register (PPR) and Data Stream Control Register (DSCR) should be
restored to the checkpointed values before the transaction began. Any changes
to these SPRs inside the transaction should not be visible in the abort
handler.
Currently Linux doesn't save or restore the checkpointed TAR, PPR or DSCR. If
we preempt a processes inside a transaction which has modified any of these, on
process restore, that same transaction may be aborted we but we won't see the
checkpointed versions of these SPRs.
This adds checkpointed versions of these SPRs to the thread_struct and adds the
save/restore of these three SPRs to the treclaim/trechkpt code.
Without this if any of these SPRs are modified during a transaction, users may
incorrectly see a speculated SPR value even if the transaction is aborted.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves us to save the Target Address Register (TAR) a earlier in
__switch_to. It introduces a new function save_tar() to do this.
We need to save the TAR earlier as we will overwrite it in the transactional
memory reclaim/recheckpoint path. We are going to do this in a subsequent
patch which will fix saving the TAR register when it's modified inside a
transaction.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
POWER8 allows the DSCR to be accessed directly from userspace via a new SPR
number 0x3 (Rather than 0x11. DSCR SPR number 0x11 is still used on POWER8 but
like POWER7, is only accessible in HV and OS modes). Currently, we allow this
by setting H/FSCR DSCR bit on boot.
Unfortunately this doesn't work, as the kernel needs to see the DSCR change so
that it knows to no longer restore the system wide version of DSCR on context
switch (ie. to set thread.dscr_inherit).
This clears the H/FSCR DSCR bit initially. If a process then accesses the DSCR
(via SPR 0x3), it'll trap into the kernel where we set thread.dscr_inherit in
facility_unavailable_exception().
We also change _switch() so that we set or clear the H/FSCR DSCR bit based on
the thread.dscr_inherit.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reworks the Facility Status and Control Regsiter (FSCR) config bit
definitions so that we can access the bit numbers. This is needed for a
subsequent patch to fix the userspace DSCR handling.
HFSCR and FSCR bit definitions are the same, so reuse them.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if we take hypervisor facility unavaliable (from 0xf80/0x4f80) we
mark it as an OS facility unavaliable (0xf60) as the two share the same code
path.
The becomes a problem in facility_unavailable_exception() as we aren't able to
see the hypervisor facility unavailable exceptions.
Below fixes this by duplication the required macros.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vscsi->num_queues counts the number of request virtqueue which does not
include the control and event virtqueue. It is wrong to subtract
VIRTIO_SCSI_VQ_BASE from vscsi->num_queues.
Problem: When Hardware IOMMU is on, megaraid_sas driver initialization fails
in kdump kernel with LSI MegaRAID controller(device id-0x73).
Actually this issue needs fix in firmware, but for firmware running in field,
this driver fix is proposed to resolve the issue. At firmware initialization
time, if firmware does not come to ready state, driver will reset the adapter
and retry for firmware transition to ready state unconditionally(not only
executed for kdump kernel).
If a device has the skip_vpd_pages flag set we should simply fail the
scsi_get_vpd_page() call.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Stuart Foster <smf.linux@ntlworld.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BT_CONFIG command that is sent to the device during
startup will enable BT coex unless the module parameter
turns it off, but on devices without Bluetooth this may
cause problems, as reported in Redhat BZ 885407.
Fix this by sending the BT_CONFIG command only when the
device has Bluetooth.
Set SSID bitmap for direct scan even on passive channels,
for the passive-to-active feature. Without this patch only
the SSID from probe request template is sent on passive
channels, after passive-to-active switching, causing us to
not find all desired networks.
Remove the unused passive scan mask constant.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slaves get the 64B CQE/EQE state from QUERY_HCA, not from the module parameter.
If the parameter is set to zero, the slave outputs an incorrect/irrelevant
warning message that 64B CQEs/EQEs are supported but not enabled (even if the
hypervisor has enabled 64B CQEs/EQEs).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user has not assigned a MAC address to a VM, then don't give it MAC which
is based on the PF one. The current derivation scheme is wrong and leads to VM
MAC collisions when the number of cards/hypervisors becomes big enough.
Instead, just give it zeros and let them figure out what to do with that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log