John Fastabend [Thu, 15 Dec 2016 20:13:24 +0000 (12:13 -0800)]
virtio_net: Add XDP support
This adds XDP support to virtio_net. Some requirements must be
met for XDP to be enabled depending on the mode. First it will
only be supported with LRO disabled so that data is not pushed
across multiple buffers. Second the MTU must be less than a page
size to avoid having to handle XDP across multiple pages.
If mergeable receive is enabled this patch only supports the case
where header and data are in the same buf which we can check when
a packet is received by looking at num_buf. If the num_buf is
greater than 1 and a XDP program is loaded the packet is dropped
and a warning is thrown. When any_header_sg is set this does not
happen and both header and data is put in a single buffer as expected
so we check this when XDP programs are loaded. Subsequent patches
will process the packet in a degraded mode to ensure connectivity
and correctness is not lost even if backend pushes packets into
multiple buffers.
If big packets mode is enabled and MTU/LRO conditions above are
met then XDP is allowed.
This patch was tested with qemu with vhost=on and vhost=off where
mergeable and big_packet modes were forced via hard coding feature
negotiation. Multiple buffers per packet was forced via a small
test patch to vhost.c in the vhost=on qemu mode.
Suggested-by: Shrijeet Mukherjee <shrijeet@gmail.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 15 Dec 2016 20:12:54 +0000 (12:12 -0800)]
net: xdp: add invalid buffer warning
This adds a warning for drivers to use when encountering an invalid
buffer for XDP. For normal cases this should not happen but to catch
this in virtual/qemu setups that I may not have expected from the
emulation layer having a standard warning is useful.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 15 Dec 2016 15:05:52 +0000 (23:05 +0800)]
sctp: sctp_transport_lookup_process should rcu_read_unlock when transport is null
Prior to this patch, sctp_transport_lookup_process didn't rcu_read_unlock
when it failed to find a transport by sctp_addrs_lookup_transport.
This patch is to fix it by moving up rcu_read_unlock right before checking
transport and also to remove the out path.
Fixes: 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 15 Dec 2016 15:00:55 +0000 (23:00 +0800)]
sctp: sctp_epaddr_lookup_transport should be protected by rcu_read_lock
Since commit 7fda702f9315 ("sctp: use new rhlist interface on sctp transport
rhashtable"), sctp has changed to use rhlist_lookup to look up transport, but
rhlist_lookup doesn't call rcu_read_lock inside, unlike rhashtable_lookup_fast.
It is called in sctp_epaddr_lookup_transport and sctp_addrs_lookup_transport.
sctp_addrs_lookup_transport is always in the protection of rcu_read_lock(),
as __sctp_lookup_association is called in rx path or sctp_lookup_association
which are in the protection of rcu_read_lock() already.
But sctp_epaddr_lookup_transport is called by sctp_endpoint_lookup_assoc, it
doesn't call rcu_read_lock, which may cause "suspicious rcu_dereference_check
usage' in __rhashtable_lookup.
This patch is to fix it by adding rcu_read_lock in sctp_endpoint_lookup_assoc
before calling sctp_epaddr_lookup_transport.
Fixes: 7fda702f9315 ("sctp: use new rhlist interface on sctp transport rhashtable") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Dec 2016 16:43:05 +0000 (11:43 -0500)]
Merge branch 'dpaa_eth-fixes'
Madalin Bucur says:
====================
dpaa_eth: a couple of fixes
This patch set introduces big endian accessors in the dpaa_eth driver
making sure accesses to the QBMan HW are correct on little endian
platforms. Removing a redundant Kconfig dependency on FSL_SOC.
Adding myself as maintainer of the dpaa_eth driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 15 Dec 2016 13:13:04 +0000 (15:13 +0200)]
dpaa_eth: use big endian accessors
Ensure correct access to the big endian QMan HW through proper
accessors.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:48 +0000 (11:42 +0100)]
irnet: ppp: move IRNET_MINOR to include/linux/miscdevice.h
This patch move the define for IRNET_MINOR to include/linux/miscdevice.h
It is better that all minor number definitions are in the same place.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 15 Dec 2016 10:42:47 +0000 (11:42 +0100)]
irda: irnet: Move linux/miscdevice.h include
The only use of miscdevice is irda_ppp so no need to include
linux/miscdevice.h for all irda files.
This patch move the linux/miscdevice.h include to irnet_ppp.h
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
inet: Fixes for inet_csk_get_port and soreusport
This patch set fixes a couple of issues I noticed while debugging our
softlockup issue in inet_csk_get_port.
- Don't allow jump into port scan in inet_csk_get_port if function
was called with non-zero port number (looking up explicit port
number).
- When inet_csk_get_port is called with zero port number (ie. perform
scan) an reuseport is set on the socket, don't match sockets that
also have reuseport set. The intent from the user should be
to get a new port number and then explictly bind other
sockets to that number using soreuseport.
Tested:
Ran first patch on production workload with no ill effect.
For second patch, ran a little listener application and first
demonstrated that unbound sockets with soreuseport can indeed
be bound to unrelated soreuseport sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 15 Dec 2016 00:54:16 +0000 (16:54 -0800)]
inet: Fix get port to handle zero port number with soreuseport set
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 15 Dec 2016 00:54:15 +0000 (16:54 -0800)]
inet: Don't go into port scan when looking for specific bind port
inet_csk_get_port is called with port number (snum argument) that may be
zero or nonzero. If it is zero, then the intent is to find an available
ephemeral port number to bind to. If snum is non-zero then the caller
is asking to allocate a specific port number. In the latter case we
never want to perform the scan in ephemeral port range. It is
conceivable that this can happen if the "goto again" in "tb_found:"
is done. This patch adds a check that snum is zero before doing
the "goto again".
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The test case is correct, just that the error outcome changed with ebb676daa1a3 ("bpf: Print function name in addition to function id").
Same as with e00c7b216f34 ("bpf: fix multiple issues in selftest suite
and samples") issue 2), so just fix up the function name.
Fixes: ebb676daa1a3 ("bpf: Print function name in addition to function id") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 15 Dec 2016 00:30:06 +0000 (01:30 +0100)]
bpf: fix regression on verifier pruning wrt map lookups
Commit 57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL
registers") introduced a regression where existing programs stopped
loading due to reaching the verifier's maximum complexity limit,
whereas prior to this commit they were loading just fine; the affected
program has roughly 2k instructions.
What was found is that state pruning couldn't be performed effectively
anymore due to mismatches of the verifier's register state, in particular
in the id tracking. It doesn't mean that 57a09bf0a416 is incorrect per
se, but rather that verifier needs to perform a lot more work for the
same program with regards to involved map lookups.
Since commit 57a09bf0a416 is only about tracking registers with type
PTR_TO_MAP_VALUE_OR_NULL, the id is only needed to follow registers
until they are promoted through pattern matching with a NULL check to
either PTR_TO_MAP_VALUE or UNKNOWN_VALUE type. After that point, the
id becomes irrelevant for the transitioned types.
For UNKNOWN_VALUE, id is already reset to 0 via mark_reg_unknown_value(),
but not so for PTR_TO_MAP_VALUE where id is becoming stale. It's even
transferred further into other types that don't make use of it. Among
others, one example is where UNKNOWN_VALUE is set on function call
return with RET_INTEGER return type.
states_equal() will then fall through the memcmp() on register state;
note that the second memcmp() uses offsetofend(), so the id is part of
that since d2a4dd37f6b4 ("bpf: fix state equivalence"). But the bisect
pointed already to 57a09bf0a416, where we really reach beyond complexity
limit. What I found was that states_equal() often failed in this
case due to id mismatches in spilled regs with registers in type
PTR_TO_MAP_VALUE. Unlike non-spilled regs, spilled regs just perform
a memcmp() on their reg state and don't have any other optimizations
in place, therefore also id was relevant in this case for making a
pruning decision.
We can safely reset id to 0 as well when converting to PTR_TO_MAP_VALUE.
For the affected program, it resulted in a ~17 fold reduction of
complexity and let the program load fine again. Selftest suite also
runs fine. The only other place where env->id_gen is used currently is
through direct packet access, but for these cases id is long living, thus
a different scenario.
Also, the current logic in mark_map_regs() is not fully correct when
marking NULL branch with UNKNOWN_VALUE. We need to cache the destination
reg's id in any case. Otherwise, once we marked that reg as UNKNOWN_VALUE,
it's id is reset and any subsequent registers that hold the original id
and are of type PTR_TO_MAP_VALUE_OR_NULL won't be marked UNKNOWN_VALUE
anymore, since mark_map_reg() reuses the uncached regs[regno].id that
was just overridden. Note, we don't need to cache it outside of
mark_map_regs(), since it's called once on this_branch and the other
time on other_branch, which are both two independent verifier states.
A test case for this is added here, too.
Fixes: 57a09bf0a416 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Thomas Graf <tgraf@suug.ch> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 14 Dec 2016 22:31:11 +0000 (14:31 -0800)]
net: vrf: Drop conntrack data after pass through VRF device on Tx
Locally originated traffic in a VRF fails in the presence of a POSTROUTING
rule. For example,
$ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE
$ ping -I red -c1 11.1.1.3
ping: Warning: source address might be selected on device other than red.
PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data.
ping: sendmsg: Operation not permitted
Worse, the above causes random corruption resulting in a panic in random
places (I have not seen a consistent backtrace).
Call nf_reset to drop the conntrack info following the pass through the
VRF device. The nf_reset is needed on Tx but not Rx because of the order
in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress
device and on Tx it is is before the real egress device. Connection
tracking should be tied to the real egress device and not the VRF device.
Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device") Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 14 Dec 2016 19:06:18 +0000 (11:06 -0800)]
net: vrf: Fix NAT within a VRF
Connection tracking with VRF is broken because the pass through the VRF
device drops the connection tracking info. Removing the call to nf_reset
allows DNAT and MASQUERADE to work across interfaces within a VRF.
Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 14 Dec 2016 17:00:58 +0000 (19:00 +0200)]
net/sched: cls_flower: Use masked key when calling HW offloads
Zero bits on the mask signify a "don't care" on the corresponding bits
in key. Some HWs require those bits on the key to be zero. Since these
bits are masked anyway, it's okay to provide the masked key to all
drivers.
Fixes: 5b33f48842fa ('net/flower: Introduce hardware offload support') Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 14 Dec 2016 17:00:57 +0000 (19:00 +0200)]
net/sched: cls_flower: Use mask for addr_type
When addr_type is set, mask should also be set.
Fixes: 66530bdf85eb ('sched,cls_flower: set key address type when present') Fixes: bc3103f1ed40 ('net/sched: cls_flower: Classify packet in ip tunnels') Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Folta [Wed, 14 Dec 2016 06:39:15 +0000 (06:39 +0000)]
net: macb: Added PCI wrapper for Platform Driver.
There are hardware PCI implementations of Cadence GEM network
controller. This patch will allow to use such hardware with reuse of
existing Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Wed, 14 Dec 2016 00:15:09 +0000 (18:15 -0600)]
ibmveth: calculate gso_segs for large packets
Include calculations to compute the number of segments
that comprise an aggregated large packet.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Tue, 13 Dec 2016 23:49:02 +0000 (17:49 -0600)]
net: qcom/emac: don't try to claim clocks on ACPI systems
On ACPI systems, clocks are not available to drivers directly. They are
handled exclusively by ACPI and/or firmware, so there is no clock driver.
Calls to clk_get() always fail, so we should not even attempt to claim
any clocks on ACPI systems.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
encx24j600: bugfix - always move ERXTAIL to next packet in encx24j600_rx_packets
Before, encx24j600_rx_packets did not update encx24j600_priv's next_packet
member when an error occurred during packet handling (either because the
packet's RSV header indicates an error or because the encx24j600_receive_packet
method can't allocate an sk_buff).
If the next_packet member is not updated, the ERXTAIL register will be set to
the same value it had before, which means the bad packet remains in the
component's memory and its RSV header will be read again when a new packet
arrives. If the RSV header indicates a bad packet or if sk_buff allocation
continues to fail, new packets will be stored in the component's memory until
that memory is full, after which packets will be dropped.
The SETPKTDEC command is always executed though, so the encx24j600 hardware has
an incorrect count of the packets in its memory.
To prevent this, the next_packet member should always be updated, allowing the
packet to be skipped (either because it's bad, as indicated in its RSV header,
or because allocating an sk_buff failed). In the allocation failure case, this
does mean dropping a valid packet, but dropping the oldest packet to keep as
much memory as possible available for new packets seems preferable to keeping
old (but valid) packets around while dropping new ones.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
I have checked all the hisilicon ethernet driver and found only two drivers
need to be fixed to make sure set dev->dev.parent before PHY connect.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dongpo Li [Mon, 12 Dec 2016 12:03:43 +0000 (20:03 +0800)]
net: ethernet: hip04: Call SET_NETDEV_DEV()
The hip04 driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Signed-off-by: Dongpo Li <lidongpo@hisilicon.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dongpo Li [Mon, 12 Dec 2016 12:03:42 +0000 (20:03 +0800)]
net: ethernet: hisi_femac: Call SET_NETDEV_DEV()
The hisi_femac driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner") Signed-off-by: Dongpo Li <lidongpo@hisilicon.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 11 Dec 2016 20:07:19 +0000 (21:07 +0100)]
net: dsa: mv88e6xxx: Fix opps when adding vlan bridge
A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19f0 ("net: dsa: mv88e6xxx: check hardware VLAN in use") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Sun, 11 Dec 2016 17:31:22 +0000 (18:31 +0100)]
net/3com/3c515: Fix timer handling, prevent leaks and crashes
The timer handling in this driver is broken in several ways:
- corkscrew_open() initializes and arms a timer before requesting the
device interrupt. If the request fails the timer stays armed.
A second call to corkscrew_open will unconditionally reinitialize the
quued timer and arm it again. Also a immediate device removal will leave
the timer queued because close() is not called (open() failed) and
therefore nothing issues del_timer().
The reinitialization corrupts the link chain in the timer wheel hash
bucket and causes a NULL pointer dereference when the timer wheel tries
to operate on that hash bucket. Immediate device removal lets the link
chain poke into freed and possibly reused memory.
Solution: Arm the timer after the successful irq request.
- corkscrew_close() uses del_timer()
On close the timer is disarmed with del_timer() which lets the following
code race against a concurrent timer expiry function.
del_timer() is invoked even if the timer was never initialized. This
works by chance because the struct containing the timer is zeroed at
allocation time.
Solution: Move the setup of the timer into corkscrew_setup().
Reported-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 13 Dec 2016 06:23:05 +0000 (14:23 +0800)]
virtio-net: correctly enable multiqueue
Commit 4490001029012539937ff02778fe6180613fa949 ("virtio-net: enable
multiqueue by default") blindly set the affinity instead of queues
during probe which can cause a mismatch of #queues between guest and
host. This patch fixes it by setting queues.
Reported-by: Theodore Ts'o <tytso@mit.edu> Tested-by: Theodore Ts'o <tytso@mit.edu> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Michael S. Tsirkin <mst@redhat.com> Fixes: 49000102901 ("virtio-net: enable multiqueue by default") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 12 Dec 2016 17:06:38 +0000 (09:06 -0800)]
Merge tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Three patches for minor issues"
* tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: No need to append -O2 and $(LINUXINCLUDE)
tty: serial: make crisv10 explicitly non-modular
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
Linus Torvalds [Mon, 12 Dec 2016 16:51:37 +0000 (08:51 -0800)]
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull Openrisc updates from Stafford Horne:
- changes to MAINTAINER for openrisc
- probably biggest actual change is the move to memblock from bootmem
- ... plus several bug and build fixes
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: prevent VGA console, fix builds
openrisc: include l.swa in check for write data pagefault
openrisc: Updates after openrisc.net has been lost
openrisc: Consolidate setup to use memblock instead of bootmem
openrisc: remove the redundant of_platform_populate
openrisc: add NR_CPUS Kconfig default value
openrisc: Support both old (or32) and new (or1k) toolchain
openrisc: Add thread-local storage (TLS) support
openrisc: restore all regs on rt_sigreturn
openrisc: fix PTRS_PER_PGD define
Linus Torvalds [Mon, 12 Dec 2016 16:48:28 +0000 (08:48 -0800)]
Merge tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Use seq_puts() for fixed strings"
* tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/atari: Use seq_puts() in atari_get_hardware_list()
m68k/amiga: Use seq_puts() in amiga_get_hardware_list()
Linus Torvalds [Mon, 12 Dec 2016 16:46:34 +0000 (08:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: wire up pkey syscalls
AVR32-pio: Replace two seq_printf() calls by seq_puts() in pio_bank_show()
AVR32-pio: Use seq_putc() in pio_bank_show()
AVR32-clock: Combine nine seq_printf() calls into one call in clk_show()
AVR32-clock: Use seq_putc() in two functions
Linus Torvalds [Mon, 12 Dec 2016 16:44:23 +0000 (08:44 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"There are two sets of changes in this pull.
The largest is the addition of the ColdFire platform side i2c support
(the IO addressing, setup and clock definitions). The i2c hardware
module itself is driven by the kernels existing iMX i2c driver.
The other change is the addition of support for the Amcore board"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: AMCORE board, add iMX i2c support
m68k: add Sysam AMCORE open board support
m68knommu: platform support for i2c devices on ColdFire SoC
Pull sparc updates from David Miller:
"Just a bunch of small cleanups and fixes here, and support for user
probes from Allen Pais"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix a building error reported by kbuild
sparc64: fix typo in pgd_clear()
sparc64: restore irq in error paths in iommu
sparc: leon: Fix a retry loop in leon_init_timers()
sparc64: make string buffers large enough
sparc64: move dereference after check for NULL
sparc: kernel: use builtin_platform_driver
sparc64:Support User Probes for sparc
1) Platform regulatory domain support for ath10k, from Bartosz
Markowski.
2) Centralize min/max MTU checking, thus removing tons of duplicated
code all of the the various drivers. From Jarod Wilson.
3) Support ingress actions in act_mirred, from Shmulik Ladkani.
4) Improve device adjacency tracking, from David Ahern.
5) Add support for LED triggers on PHY link state changes, from Zach
Brown.
6) Improve UDP socket memory accounting, from Paolo Abeni.
7) Set SK_MEM_QUANTUM to a fixed size of 4096, instead of PAGE_SIZE.
From Eric Dumazet.
8) Collapse TCP SKBs at retransmit time even if the right side SKB has
frags. Also from Eric Dumazet.
9) Add IP_RECVFRAGSIZE and IPV6_RECVFRAGSIZE cmsgs, from Willem de
Bruijn.
10) Support routing by UID, from Lorenzo Colitti.
11) Handle L3 domain binding (ie. VRF) for RAW sockets, from David
Ahern.
12) tcp_get_info() can run lockless, from Eric Dumazet.
13) 4-tuple UDP hashing in SFC driver, from Edward Cree.
14) Avoid reorders in GRO code, from Eric Dumazet.
15) IPV6 Segment Routing support, from David Lebrun.
16) Support MPLS push and pop for L3 packets in openvswitch, from Jiri
Benc.
17) Add LRU datastructure support for BPF, Martin KaFai Lau.
18) VF support in liquidio driver, from Raghu Vatsavayi.
19) Multiqueue support in alx driver, from Tobias Regnery.
20) Networking cgroup BPF support, from Daniel Mack.
21) TCP chronograph measurements, from Francis Yan.
22) XDP support for qed driver, from Yuval Mintz.
23) BPF based lwtunnels, from Thomas Graf.
24) Consistent FIB dumping to offloading drivers, from Ido Schimmel.
25) Many optimizations for UDP under high load, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
netfilter: nft_counter: rework atomic dump and reset
e1000: use disable_hardirq() for e1000_netpoll()
i40e: don't truncate match_method assignment
net: ethernet: ti: netcp: add support of cpts
net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause
net: l2tp: ppp: change PPPOL2TP_MSG_* => L2TP_MSG_*
net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*
net: l2tp: export debug flags to UAPI
net: ethernet: stmmac: remove private tx queue lock
net: ethernet: sxgbe: remove private tx queue lock
net: bridge: shorten ageing time on topology change
net: bridge: add helper to set topology change
net: bridge: add helper to offload ageing time
net: nicvf: use new api ethtool_{get|set}_link_ksettings
net: ethernet: ti: cpsw: sync rates for channels in dual emac mode
net: ethernet: ti: cpsw: re-split res only when speed is changed
net: ethernet: ti: cpsw: combine budget and weight split and check
net: ethernet: ti: cpsw: don't start queue twice
net: ethernet: ti: cpsw: use same macros to get active slave
net: mvneta: select GENERIC_ALLOCATOR
...
Randy Dunlap [Sun, 20 Nov 2016 23:40:32 +0000 (08:40 +0900)]
openrisc: prevent VGA console, fix builds
OpenRISC does not support VGA console, so prevent that kconfig symbol
from being enabled for OpenRISC, thus fixing these build errors:
drivers/built-in.o: In function `vgacon_save_screen':
vgacon.c:(.text+0x20e0): undefined reference to `screen_info'
vgacon.c:(.text+0x20e8): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_init':
vgacon.c:(.text+0x284c): undefined reference to `screen_info'
vgacon.c:(.text+0x2850): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_startup':
vgacon.c:(.text+0x28d8): undefined reference to `screen_info'
drivers/built-in.o:vgacon.c:(.text+0x28f0): more undefined references to `screen_info' follow
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Chen Gang <gang.chen@asianux.com> Cc: Jonas Bonn <jonas@southpole.se> Signed-off-by: Stafford Horne <shorne@gmail.com>
openrisc: include l.swa in check for write data pagefault
During page fault handling we check the last instruction to understand
if the fault was for a read or for a write. By default we fall back to
read. New instructions were added to the openrisc 1.1 spec for an
atomic load/store pair (l.lwa/l.swa).
This patch adds the opcode for l.swa (0x33) allowing it to be treated as
a write operation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: expanded a bit on the comment] Signed-off-by: Stafford Horne <shorne@gmail.com>
Stafford Horne [Mon, 21 Mar 2016 08:11:10 +0000 (17:11 +0900)]
openrisc: Updates after openrisc.net has been lost
The openrisc.net domain expired and was taken over by squatters.
These updates point documentation to the new domain, mailing lists
and git repos.
Also, Jonas is not the main maintainer anylonger, he reviews changes
but does not maintain a repo or sent pull requests. Updating this to
add Stafford and Stefan who are the active maintainers.
Rob Herring [Tue, 30 Aug 2016 15:10:59 +0000 (00:10 +0900)]
openrisc: remove the redundant of_platform_populate
The of_platform_populate call in the openrisc arch code is now redundant
as the DT core provides a default call. Openrisc has a NULL match table
which means only top level nodes with compatible strings will have
devices creates. The default version will also descend nodes in the
match table such as "simple-bus" which should be fine as openrisc
doesn't have any of these (though it is preferred that memory-mapped
peripherals be grouped under a bus node(s)).
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Jonas Bonn <jonas@southpole.se> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Stafford Horne <shorne@gmail.com>
openrisc: Support both old (or32) and new (or1k) toolchain
The output file format for or1k has changed from "elf32-or32"
to "elf32-or1k". Select the correct output format automatically
to be able to compile the kernel with both toolchain variants.
Jonas Bonn [Mon, 23 Sep 2013 10:04:20 +0000 (12:04 +0200)]
openrisc: restore all regs on rt_sigreturn
Fix signal handling for when signals are handled as the result of timers
or exceptions, previous code assumed syscalls. This was noticeable with X
crashing where it uses SIGALRM.
This patch restores all regs before returning to userspace via
_resume_userspace instead of via syscall return path.
The rt_sigreturn syscall is more like a context switch than a function
call; it entails a return from one context (the signal handler) to another
(the process in question). For a context switch like this there are
effectively no call-saved regs that remain constant across the transition.
Reported-by: Sebastian Macke <sebastian@macke.de> Signed-off-by: Jonas Bonn <jonas@southpole.se> Tested-by: Guenter Roeck <linux@roeck-us.net>
[shorne@gmail.com: Updated comment better reflect change and issue] Signed-off-by: Stafford Horne <shorne@gmail.com>
On OpenRISC, with its 8k pages, PAGE_SHIFT is defined to be 13.
That makes the expression (1UL << (PAGE_SHIFT-2)) evaluate
to 2048.
The correct value for PTRS_PER_PGD should be 256.
Correcting the PTRS_PER_PGD define unveiled a bug in map_ram(),
where PTRS_PER_PGD was used when the intent was to iterate
over a set of page table entries.
This patch corrects that issue as well.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Jonas Bonn <jonas@southpole.se> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Stafford Horne <shorne@gmail.com>
>> arch/sparc/include/asm/topology_64.h:44:44:
error: implicit declaration of function 'cpu_data'
[-Werror=implicit-function-declaration]
#define topology_physical_package_id(cpu) (cpu_data(cpu).proc_id)
^
Let's include cpudata.h in topology_64.h.
Cc: Sam Ravnborg <sam@ravnborg.org> Cc: David S. Miller <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Gonglei <arei.gonglei@huawei.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 21:15:37 +0000 (00:15 +0300)]
sparc64: restore irq in error paths in iommu
There are some error paths where we should restore IRQs but we don't.
Fixes: bb620c3d3925 ("sparc: Make sparc64 use scalable lib/iommu-common.c functions") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 11:25:54 +0000 (14:25 +0300)]
sparc: leon: Fix a retry loop in leon_init_timers()
The original code causes a static checker warning because it has a
continue inside a do { } while (0); loop. In that context, a continue
and a break are equivalent. The intent was to go back to the start of
the loop so the continue was a bug.
I've added a retry label at the start and changed the continue to a goto
retry. Then I removed the do { } while (0) loop and pulled the code in
one indent level.
Fixes: 2791c1a43900 ("SPARC/LEON: added support for selecting Timer Core and Timer within core") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 11:03:55 +0000 (14:03 +0300)]
sparc64: make string buffers large enough
My static checker complains that if "lvl" is ULONG_MAX (this is 64 bit)
then some of the strings will overflow. I don't know if that's possible
but it seems simple enough to make the buffers slightly larger.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 11:01:32 +0000 (14:01 +0300)]
sparc64: move dereference after check for NULL
We shouldn't dereference "iommu" until after we have checked that it is
non-NULL.
Fixes: f08978b0fdbf ("sparc64: Enable sun4v dma ops to use IOMMU v2 APIs") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Pais [Thu, 13 Oct 2016 04:36:13 +0000 (10:06 +0530)]
sparc64:Support User Probes for sparc
Signed-off-by: Eric Saint Etienne <eric.saint.etienne@oracle.com> Signed-off-by: Allen Pais <allen.pais@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 11 Dec 2016 18:17:39 +0000 (10:17 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Two more MIPS fixes for 4.9:
- RTC: Return -ENODEV so an external RTC will be tried
- Fix mask of GPE frequency
These two have been tested on Imagination's automated test system and
also both received positive reviews on the linux-mips mailing list"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Lantiq: Fix mask of GPE frequency
MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time
Pablo Neira [Sun, 11 Dec 2016 10:43:59 +0000 (11:43 +0100)]
netfilter: nft_counter: rework atomic dump and reset
Dump and reset doesn't work unless cmpxchg64() is used both from packet
and control plane paths. This approach is going to be slow though.
Instead, use a percpu seqcount to fetch counters consistently, then
subtract bytes and packets in case a reset was requested.
The cpu that running over the reset code is guaranteed to own this stats
exclusively, we have to turn counters into signed 64bit though so stats
update on reset don't get wrong on underflow.
This patch is based on original sketch from Eric Dumazet.
Fixes: 43da04a593d8 ("netfilter: nf_tables: atomic dump and reset for stateful objects") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Luuk Paulussen [Wed, 7 Dec 2016 22:43:34 +0000 (11:43 +1300)]
MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time
The sync_cmos_clock function in kernel/time/ntp.c first tries to update
the internal clock of the cpu by calling the "update_persistent_clock64"
architecture specific function. If this returns -ENODEV, it then tries
to update an external RTC using "rtc_set_ntp_time".
On the mips architecture, the weak implementation of the underlying
function would return 0 if it wasn't overridden. This meant that the
sync_cmos_clock function would never try to update an external RTC
(if both CONFIG_GENERIC_CMOS_UPDATE and CONFIG_RTC_SYSTOHC are
configured)
Returning -ENODEV instead, means that an external RTC will be tried.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz> Reviewed-by: Richard Laing <richard.laing@alliedtelesis.co.nz> Reviewed-by: Scott Parlane <scott.parlane@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14649/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WANG Cong [Sat, 10 Dec 2016 22:22:42 +0000 (14:22 -0800)]
e1000: use disable_hardirq() for e1000_netpoll()
In commit 02cea3958664 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.
This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: Dave Jones <davej@codemonkey.org.uk> Suggested-by: Sabrina Dubroca <sd@queasysnail.net> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Keller, Jacob E [Fri, 9 Dec 2016 21:39:21 +0000 (13:39 -0800)]
i40e: don't truncate match_method assignment
The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Bimmy Pujari <bimmy.pujari@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WingMan Kwok [Thu, 8 Dec 2016 22:21:56 +0000 (16:21 -0600)]
net: ethernet: ti: netcp: add support of cpts
This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Wed, 7 Dec 2016 19:20:51 +0000 (13:20 -0600)]
net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*
PPPOL2TP_MSG_* and L2TP_MSG_* are duplicates, and are being used
interchangeably in the kernel, so let's standardize on L2TP_MSG_*
internally, and keep PPPOL2TP_MSG_* defined in UAPI for compatibility.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st> Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: bridge: fast ageing on topology change
802.1D [1] specifies that the bridges in a network must use a short
value to age out dynamic entries in the Filtering Database for a period,
once a topology change has been communicated by the root bridge.
This patchset fixes this for the in-kernel STP implementation.
Once the topology change flag is set in a net_bridge instance, the
ageing time value is shorten to twice the forward delay used by the
topology.
When the topology change flag is cleared, the ageing time configured for
the bridge is restored.
To accomplish that, a new bridge_ageing_time member is added to the
net_bridge structure, to store the user configured bridge ageing time.
Two helpers are added to offload the ageing time and set the topology
change flag in the net_bridge instance. Then the required logic is added
in the topology change helper if in-kernel STP is used.
When unplugging/replugging the laptop, the slave bridge (under test)
gets the topology change flag sent by the root bridge, and fast ageing
is triggered on the bridges. Once the topology change timer of the root
bridge expires, the topology change flag is cleared and the configured
ageing time is restored on the bridges.
A similar test has been done between two bridges under test.
When changing the forward delay of the root bridge with:
Vivien Didelot [Sat, 10 Dec 2016 18:44:29 +0000 (13:44 -0500)]
net: bridge: shorten ageing time on topology change
802.1D [1] specifies that the bridges must use a short value to age out
dynamic entries in the Filtering Database for a period, once a topology
change has been communicated by the root bridge.
Add a bridge_ageing_time member in the net_bridge structure to store the
bridge ageing time value configured by the user (ioctl/netlink/sysfs).
If we are using in-kernel STP, shorten the ageing time value to twice
the forward delay used by the topology when the topology change flag is
set. When the flag is cleared, restore the configured ageing time.
Vivien Didelot [Sat, 10 Dec 2016 18:44:27 +0000 (13:44 -0500)]
net: bridge: add helper to offload ageing time
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.
Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:49 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: re-split res only when speed is changed
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:48 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: combine budget and weight split and check
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sat, 10 Dec 2016 10:38:32 +0000 (11:38 +0100)]
net: mvneta: select GENERIC_ALLOCATOR
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes: a0627f776a45 ("net: marvell: Allow drivers to be built with COMPILE_TEST") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Limit the number of can filters to avoid > MAX_ORDER allocations.
Fix from Marc Kleine-Budde.
2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
configurations. From Stephen Hemminger.
3) Return proper error when memory allocation fails in
ser_gigaset_init(), from Dan Carpenter.
4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
Feng.
5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
Florian Fainelli.
6) Handle probe deferral properly in smsc911x driver.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: mlx5: Fix Kconfig help text
net: smsc911x: back out silently on probe deferrals
ibmveth: set correct gso_size and gso_type
net: ethernet: cpmac: Call SET_NETDEV_DEV()
net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
vhost-vsock: fix orphan connection reset
cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
ser_gigaset: return -ENOMEM on error instead of success
NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
can: peak: fix bad memory access and free sequence
phy: Don't increment MDIO bus refcount unless it's a different owner
netvsc: reduce maximum GSO size
drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
can: raw: raw_setsockopt: limit number of can_filter that can be set
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet Signed-off-by: Christopher Covington <cov@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 9 Dec 2016 13:18:00 +0000 (14:18 +0100)]
net: smsc911x: back out silently on probe deferrals
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log