Bluetooth: AMP: Get amp_mgr reference in HS hci_conn
When assigning amp_mgr in hci_conn (type AMP_LINK) get also reference.
In hci_conn_del those references would be put for both conn types
AMP_LINK and ACL_LINK associated with amp_mgr.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Bluetooth: Zero bredr pointer when chan is deleted
If BREDR L2CAP chan is deleted and this chan is the channel through
which High Speed traffic is routed to AMP then zero pointer to
the chan in amp_mgr to prevent accessing it.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Gustavo Padovan [Fri, 12 Oct 2012 11:35:23 +0000 (19:35 +0800)]
Bluetooth: Move bt_accept_enqueue() to l2cap_sock.c
This is part of the move the parent socket usage to l2cap_sock.c
The change is safe when it comes to locking, bt_accept_enqueue() is still
protected by the parent socket lock inside the
l2cap_sock_new_connection_cb() code.
Gustavo Padovan [Mon, 28 May 2012 22:18:14 +0000 (19:18 -0300)]
Bluetooth: Remove GFP_ATOMIC usage from l2cap_core.c
Since we change the Bluetooth core to run in process context we don't need
to use GFP_ATOMIC in many of places we were using it. The we just replace
by GFP_KERNEL.
Bluetooth: Factor out Create Configuration Response
Use function to factor out similar code. For BR/EDR send EFS
Configuration Response immediately, for HS response will be sent
after receiving HCI Logical Link Complete event in the following
patches.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Jefferson Delfes [Tue, 18 Sep 2012 17:36:54 +0000 (13:36 -0400)]
Bluetooth: Force the process of unpair command if disconnect failed
The unpair process tries to disconnect any connection pending with
remote. If there are some connection in connecting state, disconnect
command will fail and unpair mgmt command will stay pending.
That pending mgmt command can cause strange behavior like automatic
unpair after a lost connection.
Signed-off-by: Jefferson Delfes <jefferson.delfes@openbossa.org> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Bluetooth: AMP: Handle Accept phylink command status evt
When receiving HCI Command Status event for Accept Physical Link
execute HCI Write Remote AMP Assoc with data saved from A2MP Create
Physical Link Request.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Channel Selected event indicates that link information data is available.
Read it with Read Local AMP Assoc command. The data shall be sent in the
A2MP Create Physical Link Request.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving A2MP Get AMP Assoc Response execute HCI Create Physical
Link to AMP controller. Define function which will run when receiving
HCI Command Status.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Function calculates AMP keys using hmac_sha256 helper. Calculated keys
are Generic AMP Link Key (gamp) and Dedicated AMP Link Key with
keyID "802b" for 802.11 PAL.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving A2MP Get AMP Assoc Request execute Read Local AMP Assoc
HCI command to AMP controller. If the AMP Assoc data is larger than it
can fit to HCI event only fragment is read. When all fragments are read
send A2MP Get AMP Assoc Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When receiving A2MP Get Info Request execute Read Local AMP Info HCI
command to AMP controller with function to be executed upon receiving
command complete event. Function will handle A2MP Get Info Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.
While the documentation hints that there's some
hardware support for offloading MFP "decryption",
this simple implementation relies on the mac80211
stack to do the actual crypto operations.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.
Note:
As all current (and old) firmwares corrupt
incoming, protected management frames, the
decryption offloading needs to be disabled.
This will be done automatically if needed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Bolle [Fri, 21 Sep 2012 10:02:02 +0000 (12:02 +0200)]
ipw2x00: silence GCC warning for unused variable 'dev'
Building the libipw component without CONFIG_LIBIPW_DEBUG set triggers this GCC
warning:
drivers/net/wireless/ipw2x00/libipw_wx.c:526:21: warning: unused variable 'dev' [-Wunused-variable]
The cause of this warning is that, without CONFIG_LIBIPW_DEBUG set,
LIBIPW_DEBUG_WX compiles away. Fix it by substituting ieee->dev for (its
equivalent) dev.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: block scan request during heavy Tx traffic
Currently scan operation is delayed/aborted based on Tx traffic
consistency. This decision is taken after receiving scan
response of first scan command from FW. But when heavy traffic
is running, we can not even afford to send first scan command
and go off channel for 30msec. We will block scan request in
this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: disconnect the device before entering suspend state
By default, device is disconnected before entering suspend state.
User can keep the connection alive by using module parameter
"disconect_on_suspend=0".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: get rid of void pointer in struct brcmf_cfg80211_priv
Field 'pub' in struct brcmf_cfg80211_priv was types as void pointer
and filled with parameter passed in brcmf_cfg80211_attach(). This
patch makes the type specific, ie. struct brcmf_pub.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: change struct brcmf_cfg80211_priv comments to kernel-doc
Small step to fix structure commenting using kernel-doc syntax.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Wed, 19 Sep 2012 20:21:15 +0000 (22:21 +0200)]
brcmsmac: don't start device when RfKill is engaged
This patch fixes a bug when device is being started
while RfKill switch is engaged, leading to hang
due to partial initialization of hardware.
Tested-by: <dragonn@op.pl> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in routine where phy bands are determined.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 19 Sep 2012 20:21:11 +0000 (22:21 +0200)]
brcmfmac: streamline SDIO read frame routine
SDIO read non-glomming frame routine handles first frame and
follow up frame read separately. But they share a lot of common
code. This patch abstracts a brcmf_sdio_hdparser function and
optimize the code flow for better readability and future
optimization.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: store usb fw images in local linked list.
For suspend/resume it is necessary to store firmware in memory.
In order to support multiple usb dongles at the same time a linked
list of firmwares was created.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some events result in printing of the buffer when debug is
enabled. This printing was not very efficient. Changed to
macro so it comes out nice and clean without filling log buffer.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change add support for NL80211 scheduled scan. This may be used to
offload scanning to the device, which may give the host opportunity to
sleep. The newer versions of wpa_supplicant have support for this
functionality.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: extend brcmf_term_iscan() to abort e-scan
With the introduction of E-Scan there are two scan mechanisms
in the driver. I-Scan was aborted on suspend and bringing down
the device using brcmf_term_iscan(). The function has been
renamed to brcmf_abort_scanning() and covers e-scan abort as
well.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: fix sparse warnings in e-scan related code
With the introduction of e-scan mechanism in brcmfmac
(e756af5 brcmfmac: add e-scan support.) a couple of sparse
warnings were introduced. This patch resolves those.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When delayed scan operation is resumed, we just add next scan
command in queue but don't wakeup main thread to process the
command. Hence the command is downloaded to firmware only after
waking up the main thread by any other means.
This bug which was introduced after "mwifiex: improve scan delay
logic.." patch is fixed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Clean up RFCSR1 programming in rt2800_config_channel_rf3xxx.
Setting of the individual fields of the RF register can be simplified.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move RT3290 BBP initialization sequence (part) to the right place in the code.
This is just a code style change, no functional changes.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: rt2800 - Fix default vgc values for RT3572
Align with the values used by the RT3572 Ralink vendor driver v2.5.0.0.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the code in rt2800_get_default_vgc more understandable and
readable, especially for the 5GHz band values.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log