Sakari Ailus [Sun, 14 Sep 2014 21:53:06 +0000 (18:53 -0300)]
[media] smiapp: Fully probe the device in probe
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.
This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sun, 14 Sep 2014 20:59:00 +0000 (17:59 -0300)]
[media] smiapp: Split sub-device initialisation off from the registered callback
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sat, 18 Oct 2014 09:11:19 +0000 (06:11 -0300)]
[media] smiapp: Remove FSF's address from the license header
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Timo Ahonen <timo.ahonen@nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Aviv Greenberg [Wed, 3 Dec 2014 11:14:09 +0000 (08:14 -0300)]
[media] v4l: Add packed Bayer raw10 pixel formats
These formats are just like 10-bit raw bayer formats that exist already, but
the pixels are not padded to byte boundaries. Instead, the eight high order
bits of four consecutive pixels are stored in four bytes, followed by a byte
of two low order bits of each of the four pixels.
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sakari Ailus [Sun, 7 Dec 2014 22:56:38 +0000 (19:56 -0300)]
[media] DocBook: v4l: Fix raw bayer pixel format documentation wording
The documentation began with "The following four pixel formats"... but the
format definitions preceded this sentence. Replace it with "These four pixel
formats".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] VIDEO_CAFE_CCIC should select VIDEOBUF2_DMA_SG
If VIDEO_CAFE_CCIC=y, but VIDEOBUF2_DMA_SG=m:
drivers/built-in.o: In function `mcam_v4l_open':
mcam-core.c:(.text+0x1c2e81): undefined reference to `vb2_dma_sg_memops'
mcam-core.c:(.text+0x1c2eb0): undefined reference to `vb2_dma_sg_init_ctx'
drivers/built-in.o: In function `mcam_v4l_release':
mcam-core.c:(.text+0x1c34bf): undefined reference to `vb2_dma_sg_cleanup_ctx'
Hans Verkuil [Sat, 13 Dec 2014 11:53:00 +0000 (08:53 -0300)]
[media] s5k5baf: fix sparse warnings
drivers/media/i2c/s5k5baf.c:1796:33: warning: duplicate const
drivers/media/i2c/s5k5baf.c:379:24: warning: cast to restricted __le16
drivers/media/i2c/s5k5baf.c:437:11: warning: incorrect type in assignment (different base types)
drivers/media/i2c/s5k5baf.c:445:16: warning: incorrect type in return expression (different base types)
Hans Verkuil [Sat, 13 Dec 2014 11:52:57 +0000 (08:52 -0300)]
[media] m5mols: fix sparse warnings
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.
Hans Verkuil [Sat, 13 Dec 2014 11:52:56 +0000 (08:52 -0300)]
[media] hd29l2: fix sparse error and warnings
drivers/media/dvb-frontends/hd29l2.c:29:18: warning: Variable length array is used.
drivers/media/dvb-frontends/hd29l2.c:34:32: error: cannot size expression
drivers/media/dvb-frontends/hd29l2.c:125:5: warning: symbol 'hd29l2_rd_reg_mask' was not declared. Should it be static?
Variable length arrays are frowned upon, so replace with a fixed length and check
that there won't be a buffer overrun.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Sat, 13 Dec 2014 11:52:54 +0000 (08:52 -0300)]
[media] videobuf2-vmalloc: fix sparse warning
Fix this warning:
drivers/media/v4l2-core/videobuf2-vmalloc.c:98:28: warning: incorrect type in assignment (different address spaces)
drivers/media/v4l2-core/videobuf2-vmalloc.c:158:28: warning: incorrect type in argument 1 (different address spaces)
The warning is correct, but we have no other choice here to forcibly cast.
At least it is now explicit that such a cast is needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Sat, 13 Dec 2014 11:52:52 +0000 (08:52 -0300)]
[media] budget-core: fix sparse warnings
Fixes these sparse warnings.
drivers/media/pci/ttpci/budget-core.c:250:17: warning: context imbalance in 'ttpci_budget_debiread' - different lock contexts for basic block
drivers/media/pci/ttpci/budget-core.c:289:17: warning: context imbalance in 'ttpci_budget_debiwrite' - different lock contexts for basic block
To be honest, the new code does look better than the old.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 1 Dec 2014 13:10:44 +0000 (10:10 -0300)]
[media] v4l2 core: improve debug flag handling
The old debug field is renamed to dev_debug to ensure that existing drivers
(including out-of-tree drivers) that try to use the old name will no longer
compile. A comment has also been added that makes it explicit that drivers
shouldn't use this field.
Additional bits have been added to the debug flag to be more fine-grained
when debugging, especially when dealing with streaming ioctls and read,
write and poll. You want to enable those explicitly to prevent flooding
the log when streaming unless you actually want to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It made motion event never appear in my installation.
That code is complicated, so I couldn't figure out quickly how to fix
it, so dropping it seems better to me.
Another justification is that anyway application would implement
"motion signal stabilization" if required, it is not necessarily kernel
driver's job.
Hans Verkuil [Fri, 12 Dec 2014 13:28:00 +0000 (10:28 -0300)]
[media] cx25821: remove video output support
The video output functionality never worked for this driver. Now remove the
creation of the output video nodes as well to prevent users from thinking
that video output is available, when it isn't.
To correctly implement this the video output should use vb2 as well, and
that requires rewriting the output DMA setup. But without hardware to test
I am not able to do that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Fri, 12 Dec 2014 13:27:56 +0000 (10:27 -0300)]
[media] btcx-risc: move to bt8xx
The btcx-risc module is no longer used by other drivers except for bttv.
So move it from common to bt8xx and make it part of the bttv driver instead
of as a separate module.
This module should never have been a common module since most of the code
has always been bttv specific.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Fri, 12 Dec 2014 13:27:55 +0000 (10:27 -0300)]
[media] cx231xx: remove btcx_riscmem reference
Remove this comment block, it's unused. This removes the btcx_riscmem
reference as well, since that will no longer be available to other
drivers except bttv.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Takanari Hayama [Thu, 27 Nov 2014 01:25:02 +0000 (22:25 -0300)]
[media] v4l: vsp1: Always enable virtual RPF when BRU is in use
Regardless of a number of inputs, we should always enable virtual RPF
when BRU is used. This allows the case when there's only one input to
BRU, and a size of the input is smaller than a size of an output of BRU.
William Manley [Mon, 8 Dec 2014 18:57:58 +0000 (15:57 -0300)]
[media] uvcvideo: Add GUID for BGR 8:8:8
The Magewell XI100DUSB-HDMI[1] video capture device reports the pixel
format "e436eb7d-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGR 8:8:8.
The UVC 1.5 spec[2] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[3] - or at least the Media Format SDK was the only hit that
Google gave when searching for the GUID. This Media Format SDK defines
this GUID as corresponding to `MEDIASUBTYPE_RGB24`. Note though, the
XI100DUSB outputs BGR e.g. byte-reversed. I don't know if its the
capture device in error or Microsoft mean BGR when they say RGB.
Lad, Prabhakar [Wed, 26 Nov 2014 23:25:44 +0000 (20:25 -0300)]
[media] media: usb: uvc: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and wait_finish()
callbacks from vb2_ops and instead uses the the helpers
vb2_ops_wait_prepare/finish() provided by the vb2 core, the lock member
of the queue needs to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Laurent Pinchart [Tue, 28 Oct 2014 12:07:37 +0000 (09:07 -0300)]
[media] v4l: omap4iss: Stop started entities when pipeline start fails
If an entity can't be started when starting a pipeline we need to clean
up by stopping all entities that have been successfully started.
Otherwise the hardware and software states won't match, potentially
leading to crashes (for instance due to the CSI2 receiver receiving
interrupts with a NULL pipeline pointer).
[media] v4l: omap4iss: csi2: Perform real frame number propagation
Compute the pipeline frame number from the frame number sent by the
sensor instead of incrementing the frame number in software. This
improves dropped frames detection.
[media] v4l: omap4iss: Remove bogus frame number propagation
Frame number propagation tries to increase the robustness of the frame
number counter by using sources less likely to be missed than the end of
frame interrupts, such as hardware frame counters or start of frame
interrupts.
Increasing the frame number in the IPIPE ISIF and resizer end of frame
interrupt handlers is pointless as it doesn't bring any improvement.
Don't do it.
Hans Verkuil [Thu, 4 Dec 2014 09:54:52 +0000 (06:54 -0300)]
[media] v4l2 subdevs: replace get/set_crop by get/set_selection
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:32 +0000 (19:42 -0300)]
[media] media: s5p-mfc: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:30 +0000 (19:42 -0300)]
[media] media: s5p-tv: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:28 +0000 (19:42 -0300)]
[media] media: sh_veu: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:26 +0000 (19:42 -0300)]
[media] media: exynos-gsc: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:25 +0000 (19:42 -0300)]
[media] media: ti-vpe: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Prabhakar Lad [Wed, 26 Nov 2014 22:42:24 +0000 (19:42 -0300)]
[media] media: s3c-camif: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Linus Torvalds [Sun, 21 Dec 2014 00:48:59 +0000 (16:48 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
Linus Torvalds [Sun, 21 Dec 2014 00:42:36 +0000 (16:42 -0800)]
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Linus Torvalds [Sat, 20 Dec 2014 21:52:52 +0000 (13:52 -0800)]
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
Linus Torvalds [Sat, 20 Dec 2014 21:42:57 +0000 (13:42 -0800)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Linus Torvalds [Sat, 20 Dec 2014 21:37:44 +0000 (13:37 -0800)]
Merge tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
Linus Torvalds [Sat, 20 Dec 2014 21:33:03 +0000 (13:33 -0800)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"There are only a few things in the misc branch:
- Fix for bugon.cocci semantic patch
- Kdevelop4 files are .gitignored
- Put make binrpm-pkg on diet"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/package: binrpm-pkg do not create source and devel package
.gitignore: Add Kdevelop4 project files
bugon.cocci: fix Options at the macro
Linus Torvalds [Sat, 20 Dec 2014 21:31:14 +0000 (13:31 -0800)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Here are the kbuild changes for v3.19-rc1:
- Cleanups and deduplication in the main Makefile and
scripts/Makefile.*
- Sort the output of *config targets in make help
- Old <linux/version.h> is always removed to avoid a surprise during
bisecting
- Warning fix in kconfig"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: remove redundant -rR flag of hdr-inst
kbuild: Fix make help-<board series> on powerpc
kbuild: Automatically remove stale <linux/version.h> file
kconfig: Fix warning "‘jump’ may be used uninitialized"
Makefile: sort list of defconfig targets in make help output
kbuild: Remove duplicate $(cmd) definition in Makefile.clean
kbuild: collect shorthands into scripts/Kbuild.include
Linus Torvalds [Sat, 20 Dec 2014 02:19:19 +0000 (18:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile #3 from Al Viro:
"Assorted fixes and patches from the last cycle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] chunk lost from bd9b51
vfs: make mounts and mountstats honor root dir like mountinfo does
vfs: cleanup show_mountinfo
init: fix read-write root mount
unfuck binfmt_misc.c (broken by commit e6084d4)
vm_area_operations: kill ->migrate()
new helper: iter_is_iovec()
move_extent_per_page(): get rid of unused w_flags
lustre: get rid of playing with ->fs
btrfs: filp_open() returns ERR_PTR() on failure, not NULL...
Linus Torvalds [Sat, 20 Dec 2014 02:15:12 +0000 (18:15 -0800)]
Merge tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs fixes from Tyler Hicks:
"Fixes for filename decryption and encrypted view plus a cleanup
- The filename decryption routines were, at times, writing a zero
byte one character past the end of the filename buffer
- The encrypted view feature attempted, and failed, to roll its own
form of enforcing a read-only mount instead of letting the VFS
enforce it"
* tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Remove buggy and unnecessary write in file name decode routine
eCryptfs: Remove unnecessary casts when parsing packet lengths
eCryptfs: Force RO mount when encrypted view is enabled
Linus Torvalds [Sat, 20 Dec 2014 02:10:42 +0000 (18:10 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This is part two of our merge window patches.
These are all from Filipe, and fix some really hard to find races that
can cause corruptions. Most of them involved block group removal
(balance) or discard"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: remove non-sense btrfs_error_discard_extent() function
Btrfs: fix fs corruption on transaction abort if device supports discard
Btrfs: always clear a block group node when removing it from the tree
Btrfs: ensure deletion from pinned_chunks list is protected
Linus Torvalds [Sat, 20 Dec 2014 02:07:17 +0000 (18:07 -0800)]
Merge tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have landed after the previous pull request.
All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync"
* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
ALSA: hda/realtek - New codec support for ALC298
ALSA: asihpi: update to HPI version 4.14
ALSA: asihpi: increase tuner pad cache size
ALSA: asihpi: relax firmware version check
ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
ALSA: hda - Add quirk for Packard Bell EasyNote MX65
ALSA: usb-audio: add native DSD support for Matrix Audio DACs
ALSA: hda/realtek - New codec support for ALC256
ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
ASoC: Intel: fix possible acpi enumeration panic
ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
ASoC: Intel: fix return value check in sst_acpi_probe()
ALSA: hda - Make add_stereo_mix_input flag tristate
ALSA: hda - Create capture source ctls when stereo mix input is added
ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
ALSA: hda - add codec ID for Skylake display audio codec
ALSA: oxfw: some signedness bugs
ALSA: oxfw: fix detect_loud_models() return value
ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
...
Linus Torvalds [Sat, 20 Dec 2014 02:02:22 +0000 (18:02 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
Linus Torvalds [Sat, 20 Dec 2014 01:57:51 +0000 (17:57 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel
Pull arch/hexagon updates from Richard Kuo:
"Build cleanup and a few misc fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Hexagon: fix signal delivery for debug traps
Hexagon: set ARCH_DMA_MINALIGN
Hexagon: fix alignment of init_task in RW_DATA_SECTION
hexagon: Fix build failures in linux-next
Linus Torvalds [Sat, 20 Dec 2014 01:08:14 +0000 (17:08 -0800)]
Merge tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/chris updates from Jesper Nilsson:
"Mostly cleanup and build fixes for CRISv32 allmodconfig
God Jul och Gott Nytt år!"
* tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
CRISv32: Remove last remnants of ETRAX_SPI_MMC_BOARD
CRISv32: ETRAXFS: Fix recursive spinlock
CRISv32: Select MTDRAM for axisflashmap
CRISv32: Implement early console
CRIS: Use KALLSYMs if available in call stack dump
CRISv32: Fix declaration mismatch
CRISv32: Rewrite of synchronous serial port driver
CRIS: Update init memory handling
CRISv32: Better handling of watchdog bite
CRIS: Export missing function symbols
CRIS: Export ioremap_nocache
CRIS: Fix headers_install
CRISv32: Add missing include for mm.h
CRISv32: Drop obsolete file for SPI driver
Jesper Nilsson [Tue, 7 Oct 2014 10:20:47 +0000 (12:20 +0200)]
CRIS: Export missing function symbols
strcmp was lost when all other string functions were removed,
but we still have an optimized version for this on CRISv32,
so any driver built as a module would not have access to this symbol.
In a similar manner, we had optimized versions of
csum_partial_copy_from_user and __do_clear_user
but no exported symbols for them, breaking bunch of other drivers
when built as a module.
At the same time, move EXPORT_SYMBOL(__copy_user) and
EXPORT_SYMBOL(__copy_user_zeroing) C-files so it's
located together with the function definition.
Sam Ravnborg [Mon, 14 Jul 2014 15:08:29 +0000 (17:08 +0200)]
CRIS: Fix headers_install
Fix headers_install by adjusting the path to arch files.
And delete unused Kbuild file.
Drop special handling of cris in the headers.sh script
as a nice side-effect.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Mikael Starvik <starvik@axis.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
arch/cris/arch-v32/kernel/time.c: In function 'reset_watchdog':
arch/cris/arch-v32/kernel/time.c:121:2:
error: implicit declaration of function 'global_page_state'
Linus Torvalds [Fri, 19 Dec 2014 22:02:02 +0000 (14:02 -0800)]
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Kevin Hilman <khilman@linaro.org>
Linus Torvalds [Fri, 19 Dec 2014 21:29:20 +0000 (13:29 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull NOHZ update from Thomas Gleixner:
"Remove the call into the nohz idle code from the fake 'idle' thread in
the powerclamp driver along with the export of those functions which
was smuggeled in via the thermal tree. People have tried to hack
around it in the nohz core code, but it just violates all rightful
assumptions of that code about the only valid calling context (i.e.
the proper idle task).
The powerclamp trainwreck will still work, it just wont get the
benefit of long idle sleeps"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/powerclamp: Remove tick_nohz_idle abuse
Linus Torvalds [Fri, 19 Dec 2014 21:26:08 +0000 (13:26 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core fix from Thomas Gleixner:
"A single fix plugging a long standing race between proc/stat and
proc/interrupts access and freeing of interrupt descriptors"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Prevent proc race against freeing of irq descriptors
Linus Torvalds [Fri, 19 Dec 2014 21:22:42 +0000 (13:22 -0800)]
Merge branch 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 MPX fixes from Thomas Gleixner:
"Three updates for the new MPX infrastructure:
- Use the proper error check in the trap handler
- Add a proper config option for it
- Bring documentation up to date"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mpx: Give MPX a real config option prompt
x86, mpx: Update documentation
x86_64/traps: Fix always true condition
Linus Torvalds [Fri, 19 Dec 2014 21:15:24 +0000 (13:15 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes and cleanups from Ingo Molnar:
"A kernel fix plus mostly tooling fixes, but also some tooling
restructuring and cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
perf: Fix building warning on ARM 32
perf symbols: Fix use after free in filename__read_build_id
perf evlist: Use roundup_pow_of_two
tools: Adopt roundup_pow_of_two
perf tools: Make the mmap length autotuning more robust
tools: Adopt rounddown_pow_of_two and deps
tools: Adopt fls_long and deps
tools: Move bitops.h from tools/perf/util to tools/
tools: Introduce asm-generic/bitops.h
tools lib: Move asm-generic/bitops/find.h code to tools/include and tools/lib
tools: Whitespace prep patches for moving bitops.h
tools: Move code originally from asm-generic/atomic.h into tools/include/asm-generic/
tools: Move code originally from linux/log2.h to tools/include/linux/
tools: Move __ffs implementation to tools/include/asm-generic/bitops/__ffs.h
perf evlist: Do not use hard coded value for a mmap_pages default
perf trace: Let the perf_evlist__mmap autosize the number of pages to use
perf evlist: Improve the strerror_mmap method
perf evlist: Clarify sterror_mmap variable names
perf evlist: Fixup brown paper bag on "hint" for --mmap-pages cmdline arg
perf trace: Provide a better explanation when mmap fails
...
Linus Torvalds [Fri, 19 Dec 2014 20:57:45 +0000 (12:57 -0800)]
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
projects / linux-beck.git / log