Andreas Mohr [Fri, 21 Aug 2009 00:46:06 +0000 (00:46 +0000)]
net: Fix Micrel KSZ8842 Kconfig description
Signed-off-by: Andreas Mohr <andi@lisas.de> Acked-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 20 Aug 2009 02:47:34 +0000 (02:47 +0000)]
netfilter: xt_quota: fix wrong return value (error case)
Success was indicated on a memory allocation failure, thereby causing
a crash due to a later NULL deref.
(Affects v2.6.30-rc1 up to here.)
Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 63d9950b08184e6531adceb65f64b429909cc101
(ipv6: Make v4-mapped bindings consistent with IPv4)
changes behavior of inet6_bind() for v4-mapped addresses so it should
behave the same way as inet_bind().
During this change setting of err to -EADDRNOTAVAIL got lost:
Krzysztof Hałasa [Mon, 24 Aug 2009 02:02:13 +0000 (19:02 -0700)]
E100: fix interaction with swiotlb on X86.
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Data in descriptors is
accessed simultaneously by the chip (writing status and size when
a packet is received) and CPU (reading to check if the packet was
received). This isn't a valid usage of PCI DMA API, which requires use
of the coherent (consistent) memory for such purpose. Unfortunately e100
chips working in "simplified" RX mode have to store received data
directly after the descriptor. Fixing the driver to conform to the API
would require using unsupported "flexible" RX mode or receiving data
into a coherent memory and using CPU to copy it to network buffers.
This patch, while not yet making the driver conform to the PCI DMA API,
allows it to work correctly on X86 with swiotlb (while not breaking
other architectures).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
ALSA: ali5451: fix timeout handling in snd_ali_{codecs,timer}_ready()
Modify loops in such way that the register value is checked also after
the timeout condition, just in case the heavy interrupt load etc. caused
the thread to sleep for the time period exceeding the timeout value.
While at it remove an extra ALI_STIMER read from snd_ali_stimer_ready().
setup_arch() unconditionally sets the preferred console to ttyS.
This breaks the use of 3270 devices as the console. Provide a new
function to set the default preferred console for s390. The preferred
console depends on the conmode parameter that is used to switch
between 3270 and 3215 terminal/console mode.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sebastian Ott [Sun, 23 Aug 2009 16:09:04 +0000 (18:09 +0200)]
[S390] cio: fix double free after failed device initialization
If io_subchannel_initialize_dev fails it will release the only
reference to the ccw device therefore the caller should not
kfree this device since this is done in the release function.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt2sas: fix config request and diag reset deadlock
[SCSI] mpt2sas: Bump driver version 01.100.04.00
[SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate
[SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode
[SCSI] mpt2sas: fix infinite loop inside config request
[SCSI] mpt2sas: Excessive log info causes sas iounit page time out
[SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages
[SCSI] mpt2sas: Expander fix oops saying "Already part of another port"
[SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash
Linus Torvalds [Sat, 22 Aug 2009 00:40:08 +0000 (17:40 -0700)]
Re-introduce page mapping check in mark_buffer_dirty()
In commit a8e7d49aa7be728c4ae241a75a2a124cdcabc0c5 ("Fix race in
create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test
for a NULL page mapping unintentionally when some of the code inside
__set_page_dirty() was moved to the callers.
That removal generally didn't matter, since a filesystem would serialize
truncation (which clears the page mapping) against writing (which marks
the buffer dirty), so locking at a higher level (either per-page or an
inode at a time) should mean that the buffer page would be stable. And
indeed, nothing bad seemed to happen.
Except it turns out that apparently reiserfs does something odd when
under load and writing out the journal, and we have a number of bugzilla
entries that look similar:
and it looks like reiserfs depended on that check (the common theme
seems to be "data=journal", and a journal writeback during a truncate).
I suspect reiserfs should have some additional locking, but in the
meantime this should get us back to the pre-2.6.29 behavior.
Pattern-pointed-out-by: Roland Kletzing <devzero@web.de> Cc: stable@kernel.org (2.6.29 and 2.6.30) Cc: Jeff Mahoney <jeffm@suse.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 21 Aug 2009 17:45:09 +0000 (10:45 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: add GET_PARAM/INFO support for Z pipes
drm/radeon/kms: add r100/r200 OQ support.
drm: Fix sysfs device confusion.
drm/radeon/kms: implement the bo busy ioctl properly.
Linus Torvalds [Fri, 21 Aug 2009 16:48:10 +0000 (09:48 -0700)]
x86: don't call '->send_IPI_mask()' with an empty mask
As noted in 83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask. That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.
This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.
The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f9620 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.
Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty. But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.
See
http://bugzilla.kernel.org/show_bug.cgi?id=13933
for details.
Tested-by: Thomas Björnell <thomas.bjornell@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtl8187: always set MSR_LINK_ENEDCA flag with RTL8187B
RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in
no link mode, otherwise it'll not be able to associate when this flag is
not set after the change "mac80211: fix managed mode BSSID handling".
By accident, setting BSSID of AP before association makes 8187B to
successfuly associate even when ENEDCA flag isn't set, which was the
case before the mac80211 change. But now the BSSID of AP we are trying
to associate is only available after association is successful, and
any attempt to associate without the needed flag doesn't work.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Fri, 21 Aug 2009 16:26:15 +0000 (09:26 -0700)]
Make bitmask 'and' operators return a result code
When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not. In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.
So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.
Linus Torvalds [Fri, 21 Aug 2009 16:23:57 +0000 (09:23 -0700)]
x86: don't send an IPI to the empty set of CPU's
The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy. So
just warn if a caller gives us an empty mask, and ignore it.
This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:
http://bugzilla.kernel.org/show_bug.cgi?id=13933
which causes a silent lock-up. It only seems to happen on PPro, P2, P3
and Athlon XP cores. Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's. Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz> Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com> Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de> Cc: Mike Travis <travis@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The oops did not reveal any more details about the real stack
that we have and the system got into an infinite loop of
recursive pagefaults.
So i booted with CONFIG_STACK_TRACER=y and the 'stacktrace' boot
parameter. The box did not crash (timings/conditions probably
changed a tiny bit to trigger the catastrophic crash), but the
/debug/tracing/stack_trace file was rather revealing:
There's a lot of fat functions on that stack trace, but
the largest of all is do_one_initcall(). This is due to
the boot trace entry variables being on the stack.
Fixing this is relatively easy, initcalls are fundamentally
serialized, so we can move the local variables to file scope.
Note that this large stack footprint was present for a
couple of months already - what pushed my system over
the edge was the addition of kmemleak to the call-chain:
Node may not be inserted over existing node. This causes inode tree
corruption and I was seeing crashes in inode_tree_del which I can not
reproduce after this patch.
The other way to fix this would be to tie inode lifetime in the rbtree
with inode while not in freeing state. I had a look at this but it is
not so trivial at this point. At least this patch gets things working again.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Chris Mason <chris.mason@oracle.com> Acked-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
While it's debatable whether or not a NULL device argument to
the DMA API functions is valid... since it certainly isn't
valid on devices with an IOMMU... dma-debug really shouldn't be
dereferencing null pointers either.
Guard against that in err_printk and the driver_filter
functions. A Fedora rawhide user was seeing this in one of the
dvb drivers resulting in an oops on boot.
[ A patch has been sent for testing to the driver, but I feel
the dma debugging support should be fixed as well. (There's
still a pile of legacy garbage in the kernel passing null
pointers to dma_{alloc,free}_*. :( ]
Sometimes, when using the touchscreen, it stops working till next restart
and the following message is printed:
ucb1400: unexpected IE_STATUS = 0x0
The following patch retriggers the touchscreen interrupt unconditionally.
This prevents hanging of the touchscreen in case of bogus interrupt
occurence.
Signed-off-by: Pavel Revak <palo@bielyvlk.sk> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Marek Vasut [Fri, 21 Aug 2009 05:05:53 +0000 (22:05 -0700)]
Input: ucb1400_ts - enable ADC Filter
This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.
ocfs2/dlm: Wait on lockres instead of erroring cancel requests
In case a downconvert is queued, and a flock receives a signal,
BUG_ON(lockres->l_action != OCFS2_AST_INVALID) is triggered
because a lock cancel triggers a dlmunlock while an AST is
scheduled.
To avoid this, allow a LKM_CANCEL to pass through, and let it
wait on __dlm_wait_on_lockres().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de> Acked-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Thomas Hellstrom [Thu, 20 Aug 2009 09:02:31 +0000 (19:02 +1000)]
drm: Fix sysfs device confusion.
The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.
Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jan Kara [Thu, 20 Aug 2009 16:26:52 +0000 (18:26 +0200)]
ocfs2: Add missing lock name
There is missing name for NFSSync cluster lock. This makes lockdep unhappy
because we end up passing NULL to lockdep when initializing lock key. Fix it.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Joel Becker <joel.becker@oracle.com>
Jan Beulich [Thu, 20 Aug 2009 15:14:15 +0000 (16:14 +0100)]
x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile
The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being
included, which in turn leads to it and all its dependents always
getting rebuilt independent of whether they are already up-to-date.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Linus Torvalds [Thu, 20 Aug 2009 21:55:24 +0000 (14:55 -0700)]
Merge branch 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: I2C STU300 stability updates
i2c-omap: Enable workaround for Errata 1.153 based on
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
i2c-omap: Fix I2C status ACK
Linus Walleij [Thu, 13 Aug 2009 20:14:23 +0000 (22:14 +0200)]
i2c-stu300: I2C STU300 stability updates
- blk clk is enabled when an irq arrives. The clk should be enabled,
but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
downwards.
- Number of address send attempts before giving up is increased to 12
from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Moiz Sonasath [Thu, 20 Aug 2009 16:21:15 +0000 (11:21 -0500)]
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Nishanth Menon [Thu, 20 Aug 2009 16:21:14 +0000 (11:21 -0500)]
i2c-omap: Fix I2C status ACK
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Alek Du [Sat, 8 Aug 2009 00:46:19 +0000 (08:46 +0800)]
PCI: check saved state before restore
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Alek Du <alek.du@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Petri Gynther [Thu, 20 Aug 2009 09:21:27 +0000 (02:21 -0700)]
ibm_newemac: emac_close() needs to call netif_carrier_off()
When ibm_newemac netdev instance is shutdown with "ifconfig down",
the netdev interface does not go properly down. netif_carrier_ok()
keeps returning TRUE even after "ifconfig down".
The problem can be seen when ibm_newemac instances are slaves of
a bonding interface. The bonding interface code uses netif_carrier_ok()
to determine the link status of its slaves. When ibm_newemac slave is
shutdown with "ifconfig down", the bonding interface won't detect any
link status change because netif_carrier_ok() keeps returning TRUE.
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
x86: make sure load_percpu_segment has no stackprotector
load_percpu_segment() is used to set up the per-cpu segment registers,
which are also used for -fstack-protector. Make sure that the
load_percpu_segment() function doesn't have stackprotector enabled.
[ Impact: allow percpu setup before calling stack-protected functions ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Takashi Iwai [Wed, 19 Aug 2009 18:05:02 +0000 (20:05 +0200)]
ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.
This patch adds the identification of such laptops to apply the
standard BIOS-probing method. Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Linus Torvalds [Wed, 19 Aug 2009 17:40:24 +0000 (10:40 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix oopses with doubly mounted snapshots
nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()
Anton Blanchard [Wed, 19 Aug 2009 15:10:16 +0000 (16:10 +0100)]
AFS: Documentation updates
Fix some issues with the AFS documentation, found when testing AFS on ppc64:
- Update AFS features: reading/writing, local caching
- Typo in kafs sysfs debug file
- Use modprobe instead of insmod in example
- Update IPs for grand.central.org
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 19 Aug 2009 17:38:36 +0000 (10:38 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: teardown crtc correctly when fb is destroyed.
drm/kms/radeon: cleanup combios TV table like DDX.
drm/radeon/kms: memset the allocated framebuffer before using it.
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
drm/radeon/kms: implement bo busy check + current domain
drm/radeon/kms: cut down indirects in register accesses.
drm/radeon/kms: Fix up vertical blank interrupt support.
drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
drm/edid: fixup detailed timings like the X server.
drm/radeon/kms: Add specific rs690 authorized register table
Linus Torvalds [Wed, 19 Aug 2009 16:44:51 +0000 (09:44 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Update Microblaze defconfigs
microblaze: Use klimit instead of _end for memory init
microblaze: Enable ppoll syscall
microblaze: Sane handling of missing timer/intc in device tree
microblaze: use the generic ack_bad_irq implementation
Suresh Siddha [Mon, 17 Aug 2009 21:34:59 +0000 (14:34 -0700)]
clockevent: Prevent dead lock on clockevents_lock
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.
This results in a deadlock in this scenario.
cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.
This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.
Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.
Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.
This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Peter Zijlstra [Wed, 19 Aug 2009 09:18:26 +0000 (11:18 +0200)]
perf tools: Check perf.data owner
Add an owner check to opening perf.data files and a switch to
silence it.
Because perf-report/perf-annotate are binary parsers reading
another users' perf.data file could be a security risk if the
file were explicitly engineered to trigger bugs in the parser
(we hope of course there are non such bugs, but you never
know).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090819092023.896648538@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Wu Fengguang [Wed, 19 Aug 2009 08:58:59 +0000 (16:58 +0800)]
ALSA: hda: enable speaker output for Compaq 6530s/6531s
HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.
The codec differences before/after patch are:
@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
Conn = Digital, Color = White
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
- Pin-ctls: 0x24: IN
+ Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
Pin Default 0x41813021: [N/A] Line In at Ext Rear
Conn = 1/8, Color = Blue
DefAssociation = 0x2, Sequence = 0x1
- Pin-ctls: 0x24: IN VREF_80
+ Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x24
Tests show that it won't impact (external) Mic recording.
David S. Miller [Wed, 19 Aug 2009 06:44:08 +0000 (23:44 -0700)]
sparc32: Kill trap table freeing code.
Normally, srmmu uses different trap table register values to allow
determination of the cpu we're on. All of the trap tables have
identical content, they just sit at different offsets from the first
trap table, and the offset shifted down and masked out determines
the cpu we are on.
The code tries to free them up when they aren't actually used
(don't have all 4 cpus, we're on sun4d, etc.) but that causes
problems.
For one thing it triggers false positives in the DMA debugging
code. And fixing that up while preserving this relative offset
thing isn't trivial.
So just kill the freeing code, it costs us at most 3 pages, big
deal...
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Wed, 19 Aug 2009 03:21:40 +0000 (20:21 -0700)]
yellowfin: Fix buffer underrun after dev_alloc_skb() failure
yellowfin_init_ring() needs to clean up if dev_alloc_skb() fails and
should pass an error status up to the caller. This also prevents an
buffer underrun if failure occurred in the first iteration.
yellowfin_open() which calls yellowfin_init_ring() should free its
requested irq upon failure.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 19 Aug 2009 02:41:47 +0000 (19:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
security: Fix prompt for LSM_MMAP_MIN_ADDR
security: Make LSM_MMAP_MIN_ADDR default match its help text.
Linus Torvalds [Wed, 19 Aug 2009 02:41:05 +0000 (19:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: use the right flag for get_vm_area()
percpu, sparc64: fix sparse possible cpu map handling
init: set nr_cpu_ids before setup_per_cpu_areas()
Jiri Olsa [Tue, 11 Aug 2009 15:29:04 +0000 (17:29 +0200)]
tracing: handle broken names in ftrace filter
If one filter item (for set_ftrace_filter and set_ftrace_notrace) is being
setup by more than 1 consecutive writes (FTRACE_ITER_CONT flag), it won't
be handled corretly.
after change:
sh-4.0# echo > ./set_ftrace_notrace
sh-4.0# test ./set_ftrace_notrace "sys" "_open "
sh-4.0# cat ./set_ftrace_notrace
sys_open
sh-4.0#
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
LKML-Reference: <20090811152904.GA26065@jolsa.lab.eng.brq.redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Bo Liu [Tue, 18 Aug 2009 21:11:19 +0000 (14:11 -0700)]
mm: build_zonelists(): move clear node_load[] to __build_all_zonelists()
If node_load[] is cleared everytime build_zonelists() is
called,node_load[] will have no help to find the next node that should
appear in the given node's fallback list.
Because of the bug, zonelist's node_order is not calculated as expected.
This bug affects on big machine, which has asynmetric node distance.
This (my bug) is very old but no one has reported this for a long time.
Maybe because the number of asynmetric NUMA is very small and they use
cpuset for customizing node memory allocation fallback.
[akpm@linux-foundation.org: fix CONFIG_NUMA=n build] Signed-off-by: Bo Liu <bo-liu@hotmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Graff Yang [Tue, 18 Aug 2009 21:11:17 +0000 (14:11 -0700)]
nommu: check fd read permission in validate_mmap_request()
According to the POSIX (1003.1-2008), the file descriptor shall have been
opened with read permission, regardless of the protection options specified to
mmap(). The ltp test cases mmap06/07 need this.
Signed-off-by: Graff Yang <graff.yang@gmail.com> Acked-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Greg Ungerer <gerg@snapgear.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 18 Aug 2009 21:11:17 +0000 (14:11 -0700)]
spi_s3c24xx: fix transfer setup code
Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero. We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 18 Aug 2009 21:11:16 +0000 (14:11 -0700)]
spi_s3c24xx: fix clock rate calculation
Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.
Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 18 Aug 2009 21:11:12 +0000 (14:11 -0700)]
mmc: add the new linux-mmc mailing list to MAINTAINERS
There are a number of individual MMC drivers listed in MAINTAINERS. I
didn't modify those records. Perhaps I should have.
Cc: <linux-mmc@vger.kernel.org> Cc: Manuel Lauss <manuel.lauss@gmail.com> Cc: Nicolas Pitre <nico@cam.org> Cc: Pierre Ossman <drzeus@drzeus.cx> Cc: Pavel Pisa <ppisa@pikron.com> Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Sascha Sommer <saschasommer@freenet.de> Cc: Ian Molton <ian@mnementh.co.uk> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <HaraldWelte@viatech.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Tue, 18 Aug 2009 21:11:10 +0000 (14:11 -0700)]
mm: revert "oom: move oom_adj value"
The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct. It was a very good first step for sanitize OOM.
However Paul Menage reported the commit makes regression to his job
scheduler. Current OOM logic can kill OOM_DISABLED process.
Why? His program has the code of similar to the following.
...
set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
...
if (vfork() == 0) {
set_oom_adj(0); /* Invoked child can be killed */
execve("foo-bar-cmd");
}
....
vfork() parent and child are shared the same mm_struct. then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent. Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.
Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.
Then, this patch revert commit 2ff05b2b and related commit.
Reverted commit list
---------------------
- commit 2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct)
- commit 4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit 8123681022 (oom: only oom kill exiting tasks with attached memory)
- commit 933b787b57 (mm: copy over oom_adj value at fork time)
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Paul Menage <menage@google.com> Cc: David Rientjes <rientjes@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Rik van Riel <riel@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Tue, 18 Aug 2009 21:11:08 +0000 (14:11 -0700)]
vfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed
get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast
to a signed value. Fix it to use MAX_LFS_FILESIZE which casts properly
to a positive signed value.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Steve French <smfrench@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Robert Love <rlove@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Tue, 18 Aug 2009 17:47:37 +0000 (13:47 -0400)]
security: Make LSM_MMAP_MIN_ADDR default match its help text.
Commit 788084aba2ab7348257597496befcbccabdc98a3 added the LSM_MMAP_MIN_ADDR
option, whose help text states "For most ia64, ppc64 and x86 users with lots
of address space a value of 65536 is reasonable and should cause no problems."
Which implies that it's default setting was typoed.
Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
net: restore gnet_stats_basic to previous definition
NETROM: Fix use of static buffer
e1000e: fix use of pci_enable_pcie_error_reporting
e1000e: WoL does not work on 82577/82578 with manageability enabled
cnic: Fix locking in init/exit calls.
cnic: Fix locking in start/stop calls.
bnx2: Use mutex on slow path cnic calls.
cnic: Refine registration with bnx2.
cnic: Fix symbol_put_addr() panic on ia64.
gre: Fix MTU calculation for bound GRE tunnels
pegasus: Add new device ID.
drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL
rt2x00: fix memory corruption in rf cache, add a sanity check
ixgbe: Fix receive on real device when VLANs are configured
ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion
netxen: free napi resources during detach
netxen: remove netxen workqueue
ixgbe: fix issues setting rx-usecs with legacy interrupts
can: fix oops caused by wrong rtnl newlink usage
...
BUG: sleeping function called from invalid context at arch/x86/mm/fault.c:1069
in_atomic(): 0, irqs_disabled(): 1, pid: 3886, name: umount.nilfs2
1 lock held by umount.nilfs2/3886:
#0: (&type->s_umount_key#31){+.+...}, at: [<c10b398a>] deactivate_super+0x52/0x6c
irq event stamp: 1219
hardirqs last enabled at (1219): [<c135c774>] __mutex_unlock_slowpath+0xf8/0x119
hardirqs last disabled at (1218): [<c135c6d5>] __mutex_unlock_slowpath+0x59/0x119
softirqs last enabled at (1214): [<c1033316>] __do_softirq+0x1a5/0x1ad
softirqs last disabled at (1205): [<c1033354>] do_softirq+0x36/0x5a
Pid: 3886, comm: umount.nilfs2 Not tainted 2.6.31-rc6 #55
Call Trace:
[<c1023549>] __might_sleep+0x107/0x10e
[<c13603c0>] do_page_fault+0x246/0x397
[<c136017a>] ? do_page_fault+0x0/0x397
[<c135e753>] error_code+0x6b/0x70
[<c136017a>] ? do_page_fault+0x0/0x397
[<c104f805>] ? __lock_acquire+0x91/0x12fd
[<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
[<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
[<c1050b2b>] lock_acquire+0xba/0xdd
[<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
[<c135d4fe>] down_write+0x2a/0x46
[<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
[<d0d17d3f>] nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
[<c104ea2c>] ? mark_held_locks+0x43/0x5b
[<c104ecb1>] ? trace_hardirqs_on_caller+0x10b/0x133
[<c104ece4>] ? trace_hardirqs_on+0xb/0xd
[<d0d09ac1>] nilfs_put_super+0x2f/0xca [nilfs2]
[<c10b3352>] generic_shutdown_super+0x49/0xb8
[<c10b33de>] kill_block_super+0x1d/0x31
[<c10e6599>] ? vfs_quota_off+0x0/0x12
[<c10b398f>] deactivate_super+0x57/0x6c
[<c10c4bc3>] mntput_no_expire+0x8c/0xb4
[<c10c5094>] sys_umount+0x27f/0x2a4
[<c10c50c6>] sys_oldumount+0xd/0xf
[<c10031a4>] sysenter_do_call+0x12/0x38
...
This turns out to be a bug brought by an -rc1 patch ("nilfs2: simplify
remaining sget() use").
In the patch, a new "put resource" function, nilfs_put_sbinfo()
was introduced to delay freeing nilfs_sb_info struct.
But the nilfs_put_sbinfo() mistakenly used atomic_dec_and_test()
function to check the reference count, and it caused the nilfs_sb_info
was freed when user mounted a snapshot twice.
This bug also suggests there was unseen memory leak in usual mount
/umount operations for nilfs.
Jan Beulich [Tue, 18 Aug 2009 15:41:33 +0000 (16:41 +0100)]
i386: Fix section mismatches for init code with !HOTPLUG_CPU
Commit 0e83815be719d3391bf5ea24b7fe696c07dbd417 changed the
section the initial_code variable gets allocated in, in an
attempt to address a section conflict warning. This, however
created a new section conflict when building without
HOTPLUG_CPU. The apparently only (reasonable) way to address
this is to always use __REFDATA.
Once at it, also fix a second section mismatch when not using
HOTPLUG_CPU.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Mon, 17 Aug 2009 12:07:16 +0000 (14:07 +0200)]
genirq: Wake up irq thread after action has been installed
The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.
Move the wakeup after the action is installed and action->irq has been
set.
Reported-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Michael Buesch <mb@bu3sch.de>
The librarization of the thread helpers between annotate and
report lost some perf report specifics.
thread__insert_map() had its most uptodate version in perf
report which cared about partial map overlapping. In case of
overlap between two maps, perf annotate's version removes the
whole old map without considering if it partially or
absolutely overlaps the new map.
We exported the odd version, change it by using the perf
report version.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1250607843-7395-1-git-send-email-fweisbec@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
#0 map__clone (self=<value optimized out>) at builtin-annotate.c:236
#1 thread__fork (self=<value optimized out>) at builtin-annotate.c:372
The bug here was that builtin-annotate.c was a copy of
builtin-report.c and a threading related fix to builtin-report.c
didnt get propagated to builtin-annotate.c ...
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Tue, 18 Aug 2009 09:32:24 +0000 (11:32 +0200)]
perf_counter: Fix the PARISC build
PARISC does not build:
/home/mingo/tip/kernel/perf_counter.c: In function 'perf_counter_index':
/home/mingo/tip/kernel/perf_counter.c:2016: error: 'PERF_COUNTER_INDEX_OFFSET' undeclared (first use in this function)
/home/mingo/tip/kernel/perf_counter.c:2016: error: (Each undeclared identifier is reported only once
/home/mingo/tip/kernel/perf_counter.c:2016: error: for each function it appears in.)
As PERF_COUNTER_INDEX_OFFSET is not defined.
Now, we could define it in the architecture - but lets also provide
a core default of 0 (which happens to be what all but one
architecture uses at the moment).
Architectures that need a different index offset should set this
value in their asm/perf_counter.h files.
Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Helge Deller <deller@gmx.de> Cc: linux-parisc@vger.kernel.org Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission> Signed-off-by: Ingo Molnar <mingo@elte.hu>