Kevin Hilman [Wed, 21 Aug 2013 17:16:55 +0000 (10:16 -0700)]
Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Kevin Hilman [Mon, 19 Aug 2013 17:22:10 +0000 (10:22 -0700)]
Merge tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
* tag 'drivers-3.12' of git://git.infradead.org/linux-mvebu: (35 commits)
memory: mvebu-devbus: Remove unused variable
ARM: mvebu: Relocate PCIe node in Armada 370 RD board
ARM: mvebu: Fix AXP-WiFi-AP DT for MBUS DT binding
ARM: mvebu: add support for the AXP WiFi AP board
ARM: mvebu: use dts pre-processor for mv78230
PCI: mvebu: Adapt to the new device tree layout
bus: mvebu-mbus: Add devicetree binding
ARM: kirkwood: Relocate PCIe device tree nodes
ARM: kirkwood: Introduce MBUS_ID
ARM: kirkwood: Introduce MBus DT node
ARM: kirkwood: Use the preprocessor on device tree files
ARM: kirkwood: Split DT and legacy MBus initialization
ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
ARM: mvebu: Relocate Armada 370/XP DeviceBus device tree nodes
ARM: mvebu: Add BootROM to Armada 370/XP device tree
ARM: mvebu: Add MBus to Armada 370/XP device tree
ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files
ARM: mvebu: Initialize MBus using the DT binding
ARM: mvebu: Remove the harcoded BootROM window allocation
bus: mvebu-mbus: Factorize Armada 370/XP data structures
...
Nicolas Pitre [Wed, 14 Aug 2013 14:25:14 +0000 (10:25 -0400)]
ARM: vexpress/MCPM: fix cache disable sequence when CONFIG_FRAME_POINTER=y
If CONFIG_FRAME_POINTER=y we get the following error:
arch/arm/mach-vexpress/tc2_pm.c: In function 'tc2_pm_down':
arch/arm/mach-vexpress/tc2_pm.c:200:1: error: fp cannot be used in asm here
Let's fix that by explicitly preserving r11 on the stack and removing it
from the clobber list.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 14 Aug 2013 08:09:40 +0000 (01:09 -0700)]
Merge tag 'renesas-soc2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.12
* Increased clock coverage for r8a7740 and r8a7790 SoCs
* tag 'renesas-soc2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740: Add TPU clock entry for DT platforms
ARM: shmobile: r8a7790: clocks for Ether support
ARM: shmobile: r8a7740: Fix TPU clock name
ARM: shmobile: Insert align directives before 4 bytes data
ARM: shmobile: Force ARM mode to compile reset vector for secondary CPUs
ARM: shmobile: fix compile error when CONFIG_THUMB2_KERNEL=y
ARM: shmobile: Update romImage to relocate appended DTB
Olof Johansson [Wed, 14 Aug 2013 07:25:13 +0000 (00:25 -0700)]
Merge tag 'renesas-soc-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC updates for v3.12
* Setup arch timer based on MD pins on r8a7790 SoC
* Thermal driver support for r8a7790 SoC
* Make arch timer optional for r8a7790 and r8a73a4 SoCs
* CMT10 clock event for r8a7790 and r8a73a4 SoCs
* Increased clock coverage for r8a73a4 SoC
* MMCIF DMA definitions for r8a7740 SoC
* Disconnect SMP code from clocks on emev2 SoC
* tag 'renesas-soc-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (49 commits)
ARM: shmobile: Setup r8a7790 arch timer based on MD pins
ARM: shmobile: Introduce r8a7790_read_mode_pins()
ARM: shmobile: r8a7740: add MMCIF DMA definitions
ARM: shmobile: Disconnect EMEV2 SMP code from clocks
ARM: shmobile: Make r8a73a4 Arch timer optional
ARM: shmobile: Add r8a73a4 CMT10 clock event
ARM: shmobile: Make r8a7790 Arch timer optional
ARM: shmobile: Add r8a7790 CMT00 clock event
ARM: shmobile: Sort r8a7790 MSTP entries
ARM: shmobile: r8a73a4: add clocks for I2C controllers
ARM: shmobile: r8a73a4: add Z2 clock support
ARM: shmobile: r8a73a4: safeguard against wrong clk_set_rate() uses
ARM: shmobile: r8a73a4: implement CPU clock scaling for CPUFreq
ARM: shmobile: r8a73a4: wait for completion when kicking the clock
ARM: shmobile: r8a7790: add thermal driver support
ARM: shmobile: r8a7790: add clocks for thermal
ARM: shmobile: Add SMSC ethernet chip to KZM9D DT reference
ARM: shmobile: KZM9D DT reference implementation
ARM: shmobile: r8a7790: add MMCIF and SDHI DT templates
ARM: shmobile: r8a73a4: add MMCIF and SDHI DT templates
...
Olof Johansson [Wed, 14 Aug 2013 05:07:52 +0000 (22:07 -0700)]
Merge tag 'tc2-pm' of git://git.linaro.org/people/pawelmoll/linux into next/soc
From Pawel Moll and Nicolas Pitre:
- Fixes to the existing Vexpress DCSCB backend.
- Lorenzo's minimal SPC driver required by the TC2 MCPM backend.
- The MCPM backend enabling SMP secondary boot and CPU hotplug
on the VExpress TC2 big.LITTLE platform.
- MCPM suspend method to the TC2 backend allowing basic CPU
idle/suspend. The cpuidle driver that hooks into this will be
submitted separately.
* tag 'tc2-pm' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress/TC2: implement PM suspend method
ARM: vexpress/TC2: basic PM support
ARM: vexpress: Add SCC to V2P-CA15_A7's device tree
ARM: vexpress/TC2: add Serial Power Controller (SPC) support
ARM: vexpress/dcscb: fix cache disabling sequences
Stephen Warren [Mon, 6 May 2013 20:19:19 +0000 (14:19 -0600)]
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
Tegra20 HW appears to have a bug such that PCIe device interrupts,
whether they are legacy IRQs or MSI, are lost when LP2 is enabled. To
work around this, simply disable LP2 if any PCIe devices with interrupts
are present. Detect this via the IRQ domain map operation. This is
slightly over-conservative; if a device with an interrupt is present but
the driver does not actually use them, LP2 will still be disabled.
However, this is a reasonable trade-off which enables a simpler
workaround.
Stephen Warren [Fri, 9 Aug 2013 14:49:25 +0000 (16:49 +0200)]
PCI: tegra: set up PADS_REFCLK_CFG1
The registers PADS_REFCLK_CFG are an array of 16-bit data, one entry per
PCIe root port. For Tegra30, we therefore need to write a 3rd entry in
this array. Doing so makes the mini-PCIe slot on Beaver operate correctly.
While we're at it, add some #defines to partially document the fields
within these 16-bit values.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Jay Agarwal [Fri, 9 Aug 2013 14:49:24 +0000 (16:49 +0200)]
PCI: tegra: Add Tegra 30 PCIe support
Introduce a data structure to parameterize the driver according to SoC
generation, add Tegra30 specific code and update the device tree binding
document for Tegra30 support.
Signed-off-by: Jay Agarwal <jagarwal@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Thierry Reding [Fri, 9 Aug 2013 14:49:19 +0000 (16:49 +0200)]
PCI: tegra: Move PCIe driver to drivers/pci/host
Move the PCIe driver from arch/arm/mach-tegra into the drivers/pci/host
directory. The motivation is to collect various host controller drivers
in the same location in order to facilitate refactoring.
The Tegra PCIe driver has been largely rewritten, both in order to turn
it into a proper platform driver and to add MSI (based on code by
Krishna Kishore <kthota@nvidia.com>) as well as device tree support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com>
[swarren, split DT changes into a separate patch in another branch] Signed-off-by: Stephen Warren <swarren@nvidia.com>
Thomas Petazzoni [Tue, 13 Aug 2013 08:11:42 +0000 (10:11 +0200)]
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
Some platforms (e.g S390) don't use the generic hardirqs code and
therefore do not defined HAVE_GENERIC_HARDIRQS. This prevents using
the irq_set_chip_data() and irq_get_chip_data() functions that are
used for the default implementations of the MSI operations.
So, when CONFIG_GENERIC_HARDIRQS is not enabled, provide another
default implementation of the MSI operations, that simply errors
out. The architecture is responsible for implementing those operations
(which is the case on S390), and cannot use the msi_chip infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
R Sricharan [Wed, 6 Feb 2013 14:55:40 +0000 (20:25 +0530)]
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
The DRA7xx is a high-performance, infotainment application device,
based on enhanced OMAP architecture integrated on a 28-nm technology.
Since DRA7 is a platform supported only using DT, the cpu detection
is based on the compatibles passed from DT blobs as suggested here
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187712.html
Suggested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
R Sricharan [Thu, 7 Feb 2013 12:13:35 +0000 (17:43 +0530)]
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
DRA7xx has 8 GPIO banks so that there are 32x8 = 256 GPIOs.
In order for the gpiolib to detect and initialize these
and other TWL GPIOs, ARCH_NR_GPIO is set to 512 using the
kconfig default for DRA7.
Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
R Sricharan [Thu, 7 Feb 2013 08:23:05 +0000 (13:53 +0530)]
ARM: DRA7: board-generic: Add basic DT support
Describe minimal DT boot machine details for DRA7xx based SoC's. DRA7xx
family is based on dual core ARM CORTEX A15 using GIC as the interrupt controller.
The PRCM and timer infrastructure is reused from OMAP5 and so are the io
descriptor tables.
Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
R Sricharan [Wed, 3 Jul 2013 06:08:50 +0000 (11:38 +0530)]
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
The PRCM and MPUSS parts of DRA7 devices are quite identical
to OMAP5 so as to reuse all the existing infrastructure around it.
Makefile updates to do just that.
Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:06 +0000 (17:40 +0800)]
ARM: tegra: add LP1 suspend support for Tegra114
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored. Then jumping to "tegra_resume" that was expected to be stored
in PMC_SCRATCH41 to restore CPU context and back to kernel.
Based on the work by: Bo Yan <byan@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:05 +0000 (17:40 +0800)]
ARM: tegra: add LP1 suspend support for Tegra20
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* putting SDRAM into self-refresh
* storing some EMC registers and SCLK burst policy
* switching CPU to CLK_M (12MHz OSC)
* switching SCLK to CLK_S (32KHz OSC)
* tunning off PLLM, PLLP and PLLC
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, and PLLC
* restoring some EMC registers and SCLK burst policy
* setting up CCLK burst policy to PLLP
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLP. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.
Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:04 +0000 (17:40 +0800)]
ARM: tegra: add LP1 suspend support for Tegra30
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLX. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.
Based on the work by: Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:03 +0000 (17:40 +0800)]
ARM: tegra: add common LP1 suspend support
The LP1 suspending mode on Tegra means CPU rail off, devices and PLLs are
clock gated and SDRAM in self-refresh mode. That means the low level LP1
suspending and resuming code couldn't be run on DRAM and the CPU must
switch to the always on clock domain (a.k.a. CLK_M 12MHz oscillator). And
the system clock (SCLK) would be switched to CLK_S, a 32KHz oscillator.
The LP1 low level handling code need to be moved to IRAM area first. And
marking the LP1 mask for indicating the Tegra device is in LP1. The CPU
power timer needs to be re-calculated based on 32KHz that was originally
based on PCLK.
When resuming from LP1, the LP1 reset handler will resume PLLs and then
put DRAM to normal mode. Then jumping to the "tegra_resume" that will
restore full context before back to kernel. The "tegra_resume" handler
was expected to be found in PMC_SCRATCH41 register.
This is common LP1 procedures for Tegra, so we do these jobs mainly in
this patch:
* moving LP1 low level handling code to IRAM
* marking LP1 mask
* copying the physical address of "tegra_resume" to PMC_SCRATCH41
* re-calculate the CPU power timer based on 32KHz
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, replaced IRAM_CODE macro with IO_ADDRESS(TEGRA_IRAM_CODE_AREA)] Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:02 +0000 (17:40 +0800)]
clk: tegra114: add LP1 suspend/resume support
When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.
Cc: Mike Turquette <mturquette@linaro.org> Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:01 +0000 (17:40 +0800)]
ARM: tegra: config the polarity of the request of sys clock
When suspending to LP1 mode, the SYSCLK will be clock gated. And different
board may have different polarity of the request of SYSCLK, this patch
configure the polarity from the DT for the board.
Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Mon, 12 Aug 2013 09:40:00 +0000 (17:40 +0800)]
ARM: tegra: add common resume handling code for LP1 resuming
Add support to the Tegra CPU reset vector to detect whether the CPU is
resuming from LP1 suspend state. If it is, branch to the LP1-specific
resume code.
When Tegra enters the LP1 suspend state, the SDRAM controller is placed
into a self-refresh state. For this reason, we must place the LP1 resume
code into IRAM, so that it is accessible before SDRAM access has been
re-enabled.
Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
Some PCI drivers may need to adjust the pci_bus structure after it has
been allocated by the Linux PCI core. The PCI core allows
architectures to implement the pcibios_add_bus() and
pcibios_remove_bus() for this purpose. This commit therefore extends
the hw_pci and pci_sys_data structures of the ARM PCI core to allow
PCI drivers to register ->add_bus() and ->remove_bus() in hw_pci,
which will get called when a bus is added or removed from the system.
This will be used for example by the Marvell PCIe driver to connect a
particular PCI bus with its corresponding MSI chip to handle Message
Signaled Interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Thierry Reding <thierry.reding@gmail.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Daniel Price <daniel.price@gmail.com> Tested-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a very basic registry of msi_chip structures, so that
an IRQ controller driver can register an msi_chip, and a PCIe host
controller can find it, based on a 'struct device_node'.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thierry Reding [Fri, 9 Aug 2013 20:27:08 +0000 (22:27 +0200)]
PCI: Introduce new MSI chip infrastructure
The new struct msi_chip is used to associated an MSI controller with a
PCI bus. It is automatically handed down from the root to its children
during bus enumeration.
This patch provides default (weak) implementations for the architecture-
specific MSI functions (arch_setup_msi_irq(), arch_teardown_msi_irq()
and arch_msi_check_device()) which check if a PCI device's bus has an
attached MSI chip and forward the call appropriately.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Daniel Price <daniel.price@gmail.com> Tested-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that we have weak versions for each of the PCI MSI architecture
functions, we can actually build the MSI support for all platforms,
regardless of whether they provide or not architecture-specific
versions of those functions. For this reason, the ARCH_SUPPORTS_MSI
hidden kconfig boolean becomes useless, and this patch gets rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Daniel Price <daniel.price@gmail.com> Tested-by: Thierry Reding <thierry.reding@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: linux390@de.ibm.com Cc: linux-s390@vger.kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: x86@kernel.org Cc: Russell King <linux@arm.linux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: linux-ia64@vger.kernel.org Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: David S. Miller <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Cc: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
PCI: use weak functions for MSI arch-specific functions
Until now, the MSI architecture-specific functions could be overloaded
using a fairly complex set of #define and compile-time
conditionals. In order to prepare for the introduction of the msi_chip
infrastructure, it is desirable to switch all those functions to use
the 'weak' mechanism. This commit converts all the architectures that
were overidding those MSI functions to use the new strategy.
Note that we keep two separate, non-weak, functions
default_teardown_msi_irqs() and default_restore_msi_irqs() for the
default behavior of the arch_teardown_msi_irqs() and
arch_restore_msi_irqs(), as the default behavior is needed by x86 PCI
code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Daniel Price <daniel.price@gmail.com> Tested-by: Thierry Reding <thierry.reding@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: linux390@de.ibm.com Cc: linux-s390@vger.kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: x86@kernel.org Cc: Russell King <linux@arm.linux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: linux-ia64@vger.kernel.org Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: David S. Miller <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Cc: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds [Sun, 11 Aug 2013 23:32:26 +0000 (16:32 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three bug fixes: An fnic warning caused by sleeping under a
lock, a major regression with our updated WRITE SAME/UNMAP logic which
caused tons of USB devices (and one RAID card) to cease to function
and a megaraid_sas firmware initialisation problem which causes kdump
failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Don't attempt to send extended INQUIRY command if skip_vpd_pages is set
[SCSI] fnic: BUG: sleeping function called from invalid context during probe
[SCSI] megaraid_sas: megaraid_sas driver init fails in kdump kernel
Linus Torvalds [Sun, 11 Aug 2013 19:12:39 +0000 (12:12 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"This includes small series from Michael Neuling to fix a couple of
nasty remaining problems with the new Power8 support, also targeted at
stable 3.10, without which some new userspace accessible registers
aren't properly context switched, and in some case, can be clobbered
by the user of transactional memory.
Along with that, a few slightly more minor things, such as a missing
Kconfig option to enable handling of denorm exceptions when not
running under a hypervisor (or userspace will randomly crash when
hitting denorms with the vector unit), some nasty bugs in the new
pstore oops code, and other simple bug fixes worth having in now.
Note: I picked up the two powerpc KVM fixes as Alex Graf asked me to
handle KVM bits while he is on vacation. However I'll let him decide
whether they should go to -stable or not when he is back"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/tm: Fix context switching TAR, PPR and DSCR SPRs
powerpc: Save the TAR register earlier
powerpc: Fix context switch DSCR on POWER8
powerpc: Rework setting up H/FSCR bit definitions
powerpc: Fix hypervisor facility unavaliable vector number
powerpc/kvm/book3s_pr: Return appropriate error when allocation fails
powerpc/kvm: Add signed type cast for comparation
powerpc/eeh: Add missing procfs entry for PowerNV
powerpc/pseries: Add backward compatibilty to read old kernel oops-log
powerpc/pseries: Fix buffer overflow when reading from pstore
powerpc: On POWERNV enable PPC_DENORMALISATION by default
Linus Torvalds [Sun, 11 Aug 2013 19:11:33 +0000 (12:11 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull s390 kvm fixes from Paolo Bonzini:
"Two fixes for s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: fix pfmf non-quiescing control handling
KVM: s390: move kvm_guest_enter,exit closer to sie
Linus Torvalds [Sun, 11 Aug 2013 19:10:47 +0000 (12:10 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mv64xxx: Document the newly introduced allwinner compatible
i2c: Fix Kontron PLD prescaler calculation
i2c: i2c-mxs: Use DMA mode even for small transfers
Linus Torvalds [Sat, 10 Aug 2013 22:21:47 +0000 (15:21 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are assorted fixes, mostly from Josef nailing down xfstests
runs. Zach also has a long standing fix for problems with readdir
wrapping f_pos (or ctx->pos)
These patches were spread out over different bases, so I rebased
things on top of rc4 and retested overnight"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
Linus Torvalds [Sat, 10 Aug 2013 22:20:37 +0000 (15:20 -0700)]
Merge tag 'nfs-for-3.11-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable patch for lockd to fix Oopses due to inappropriate calls to
utsname()->nodename
- Stable patches for sunrpc to fix Oopses on shutdown when using
AF_LOCAL sockets with rpcbind
- Fix memory leak and error checking issues in nfs4_proc_lookup_mountpoint
- Fix a regression with the sync mount option failing to work for nfs4
mounts
- Fix a writeback performance issue when doing cache invalidation
- Remove an incorrect call to nfs_setsecurity in nfs_fhget
* tag 'nfs-for-3.11-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix up nfs4_proc_lookup_mountpoint
NFS: Remove unnecessary call to nfs_setsecurity in nfs_fhget()
NFSv4: Fix the sync mount option for nfs4 mounts
NFS: Fix writeback performance issue on cache invalidation
SUNRPC: If the rpcbind channel is disconnected, fail the call to unregister
SUNRPC: Don't auto-disconnect from the local rpcbind socket
LOCKD: Don't call utsname()->nodename from nlmclnt_setlockargs
Linus Torvalds [Sat, 10 Aug 2013 22:19:58 +0000 (15:19 -0700)]
Merge branch 'for-3.11' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Some fixes for a 4.1 feature that in retrospect probably should have
waited for 3.12.... But it appears to be working now"
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix SP4_MACH_CRED negotiation in EXCHANGE_ID
nfsd4: Fix MACH_CRED NULL dereference
Linus Torvalds [Sat, 10 Aug 2013 20:00:56 +0000 (13:00 -0700)]
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A couple of USB-audio fixes that should also go to stable kernels"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: do not trust too-big wMaxPacketSize values
ALSA: 6fire: fix DMA issues with URB transfer_buffer usage
Linus Torvalds [Sat, 10 Aug 2013 16:00:51 +0000 (09:00 -0700)]
Merge tag 'staging-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are 3 small fixes for staging/IIO drivers for 3.11-rc5. Nothing
huge, two IIO driver fixes, and a zcache fix. All of these have been
in linux-next for a while"
* tag 'staging-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: zcache: fix "zcache=" kernel parameter
iio: ti_am335x_adc: Fix wrong samples received on 1st read
iio:trigger: Fix use_count race condition
Linus Torvalds [Sat, 10 Aug 2013 16:00:21 +0000 (09:00 -0700)]
Merge tag 'usb-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 3 small USB fixes for 3.11-rc5.
One is a fix that the ChromeOS developers ran into on some Intel
hardware, one is a build fix, and the last is a MAINTAINERS update to
help people figure out where to send USB network driver patches.
All of these have been in linux-next for a while"
* tag 'usb-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
MAINTAINERS: Add separate section for USB NETWORKING DRIVERS
usb: xhci: add missing dma-mapping.h includes
usb: core: don't try to reset_device() a port that got just disconnected
Zach Brown [Thu, 11 Jul 2013 23:19:42 +0000 (16:19 -0700)]
btrfs: don't loop on large offsets in readdir
When btrfs readdir() hits the last entry it sets the readdir offset to a
huge value to stop buggy apps from breaking when the same name is
returned by readdir() with concurrent rename()s.
But unconditionally setting the offset to INT_MAX causes readdir() to
loop returning any entries with offsets past INT_MAX. It only takes a
few hours of constant file creation and removal to create entries past
INT_MAX.
So let's set the huge offset to LLONG_MAX if the last entry has already
overflowed 32bit loff_t. Without large offsets behaviour is identical.
With large offsets 64bit apps will work and 32bit apps will be no more
broken than they currently are if they see large offsets.
Signed-off-by: Zach Brown <zab@redhat.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Thu, 25 Jul 2013 19:11:47 +0000 (15:11 -0400)]
Btrfs: check to see if root_list is empty before adding it to dead roots
A user reported a panic when running with autodefrag and deleting snapshots.
This is because we could end up trying to add the root to the dead roots list
twice. To fix this check to see if we are empty before adding ourselves to the
dead roots list. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Mon, 22 Jul 2013 16:54:30 +0000 (12:54 -0400)]
Btrfs: release both paths before logging dir/changed extents
The ceph guys tripped over this bug where we were still holding onto the
original path that we used to copy the inode with when logging. This is based
on Chris's fix which was reported to fix the problem. We need to drop the paths
in two cases anyway so just move the drop up so that we don't have duplicate
code. Thanks,
Cc: stable@vger.kernel.org Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Thu, 11 Jul 2013 14:34:59 +0000 (10:34 -0400)]
Btrfs: allow splitting of hole em's when dropping extent cache
I noticed while running multi-threaded fsync tests that sometimes fsck would
complain about an improper gap. This happens because we fail to add a hole
extent to the file, which was happening when we'd split a hole EM because
btrfs_drop_extent_cache was just discarding the whole em instead of splitting
it. So this patch fixes this by allowing us to split a hole em properly, which
means that added holes actually get logged properly and we no longer see this
fsck error. Thankfully we're tolerant of these sort of problems so a user would
not see any adverse effects of this bug, other than fsck complaining. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Fri, 5 Jul 2013 18:03:47 +0000 (14:03 -0400)]
Btrfs: make sure the backref walker catches all refs to our extent
Because we don't mess with the offset into the extent for compressed we will
properly find both extents for this case
[extent a][extent b][rest of extent a]
but because we already added a ref for the front half we won't add the inode
information for the second half. This causes us to leak that memory and not
print out the other offset when we do logical-resolve. So fix this by calling
ulist_add_merge and then add our eie to the existing entry if there is one.
With this patch we get both offsets out of logical-resolve. With this and the
other 2 patches I've sent we now pass btrfs/276 on my vm with compress-force=lzo
set. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Fri, 5 Jul 2013 17:58:19 +0000 (13:58 -0400)]
Btrfs: fix backref walking when we hit a compressed extent
If you do btrfs inspect-internal logical-resolve on a compressed extent that has
been partly overwritten it won't find anything. This is because we try and
match the extent offset we've searched for based on the extent offset in the
data extent entry. However this doesn't work for compressed extents because the
offsets are for the uncompressed size, not the compressed size. So instead only
do this check if we are not compressed, that way we can get an actual entry for
the physical offset rather than nothing for compressed. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Fri, 5 Jul 2013 17:52:51 +0000 (13:52 -0400)]
Btrfs: do not offset physical if we're compressed
xfstest btrfs/276 was freaking out on slower boxes partly because fiemap was
offsetting the physical based on the extent offset. This is perfectly fine with
uncompressed extents, however the extent offset is into the uncompressed area,
not the compressed. So we can return a physical value that isn't at all within
the area we have allocated on disk. Fix this by returning the start of the
extent if it is compressed no matter what the offset. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Liu Bo [Wed, 3 Jul 2013 06:40:44 +0000 (14:40 +0800)]
Btrfs: fix extent buffer leak after backref walking
commit 47fb091fb787420cd195e66f162737401cce023f(Btrfs: fix unlock after free on rewinded tree blocks)
takes an extra increment on the reference of allocated dummy extent buffer, so now we
cannot free this dummy one, and end up with extent buffer leak.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Jan Schmidt <list.btrfs@jan-o-sch.net> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Liu Bo [Mon, 1 Jul 2013 14:13:26 +0000 (22:13 +0800)]
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
For partial extents, snapshot-aware defrag does not work as expected,
since
a) we use the wrong logical offset to search for parents, which should be
disk_bytenr + extent_offset, not just disk_bytenr,
b) 'offset' returned by the backref walking just refers to key.offset, not
the 'offset' stored in btrfs_extent_data_ref which is
(key.offset - extent_offset).
The reproducer:
$ mkfs.btrfs sda
$ mount sda /mnt
$ btrfs sub create /mnt/sub
$ for i in `seq 5 -1 1`; do dd if=/dev/zero of=/mnt/sub/foo bs=5k count=1 seek=$i conv=notrunc oflag=sync; done
$ btrfs sub snap /mnt/sub /mnt/snap1
$ btrfs sub snap /mnt/sub /mnt/snap2
$ sync; btrfs filesystem defrag /mnt/sub/foo;
$ umount /mnt
$ btrfs-debug-tree sda (Here we can check whether the defrag operation is snapshot-awared.
This addresses the above two problems.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Jie Liu [Fri, 28 Jun 2013 05:15:52 +0000 (13:15 +0800)]
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
Create a small file and fallocate it to a big size with
FALLOC_FL_KEEP_SIZE option, then truncate it back to the
small size again, the disk free space is not changed back
in this case. i.e,
total 4
-rw-r--r-- 1 root root 512 Jun 28 11:35 test
Filesystem Size Used Avail Use% Mounted on
....
/dev/sdb1 8.0G 56K 7.2G 1% /mnt
-rw-r--r-- 1 root root 512 Jun 28 11:35 /mnt/test
Filesystem Size Used Avail Use% Mounted on
....
/dev/sdb1 8.0G 5.1G 2.2G 70% /mnt
Filesystem Size Used Avail Use% Mounted on
....
/dev/sdb1 8.0G 5.1G 2.2G 70% /mnt
With this fix, the truncated up space is back as:
Filesystem Size Used Avail Use% Mounted on
....
/dev/sdb1 8.0G 56K 7.2G 1% /mnt
Signed-off-by: Jie Liu <jeff.liu@oracle.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Fri, 9 Aug 2013 22:07:19 +0000 (15:07 -0700)]
Merge tag 'pm+acpi-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- ACPI-based memory hotplug stopped working after a recent change,
because it's not possible to associate sufficiently many "physical"
devices with one ACPI device object due to an artificial limit. Fix
from Rafael J Wysocki removes that limit and makes memory hotplug
work again.
- A change made in 3.9 uncovered a bug in the ACPI processor driver
preventing NUMA nodes from being put offline due to an ordering
issue. Fix from Yasuaki Ishimatsu changes the ordering to make
things work again.
- One of the recent ACPI video commits (that hasn't been reverted so
far) uncovered a bug in the code handling quirky BIOSes that caused
some Asus machines to boot with backlight completely off which made
it quite difficult to use them afterward. Fix from Felipe Contreras
improves the quirk to cover this particular case correctly.
- A cpufreq user space interface change made in 3.10 inadvertently
renamed the ignore_nice_load sysfs attribute to ignore_nice which
resulted in some confusion. Fix from Viresh Kumar changes the name
back to ignore_nice_load.
- An initialization ordering change made in 3.9 broke cpufreq on
loongson2 boards. Fix from Aaro Koskinen restores the correct
initialization ordering there.
- Fix breakage resulting from a mistake made in 3.9 and causing the
detection of some graphics adapters (that were detected correctly
before) to fail. There are two objects representing the same PCIe
port in the affected systems' ACPI tables and both appear as
"enabled" and we are expected to guess which one to use. We used to
choose the right one before by pure luck, but when we tried to
address another similar corner case, the luck went away. This time
we try to make our guessing a bit more educated which is reported to
work on those systems.
- The /proc/acpi/wakeup interface code is missing some locking which
may lead to breakage if that file is written or read during hotplug
of wakeup devices. That should be rare but still possible, so it's
better to start using the appropriate locking there.
* tag 'pm+acpi-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Try harder to resolve _ADR collisions for bridges
cpufreq: rename ignore_nice as ignore_nice_load
cpufreq: loongson2: fix regression related to clock management
ACPI / processor: move try_offline_node() after acpi_unmap_lsapic()
ACPI: Drop physical_node_id_bitmap from struct acpi_device
ACPI / PM: Walk physical_node_list under physical_node_lock
ACPI / video: improve quirk check in acpi_video_bqc_quirk()
Linus Torvalds [Fri, 9 Aug 2013 22:04:09 +0000 (15:04 -0700)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes (em28xx, coda, usbtv, s5p, hdpvr and ml86v7667) and
a fix for media DocBook"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: fix dependency
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
Linus Torvalds [Fri, 9 Aug 2013 18:52:34 +0000 (11:52 -0700)]
Merge tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
Linus Torvalds [Fri, 9 Aug 2013 18:51:29 +0000 (11:51 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Mostly radeon, more fixes for dynamic power management which is is off
by default for this release anyways, but there are a large number of
testers, so I'd like to keep merging the fixes.
Otherwise, radeon UVD fixes affecting suspend/resume regressions, i915
regression fixes, one for your mac mini, ast, mgag200, cirrus ttm fix
and one regression fix in the core"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm: Don't pass negative delta to ktime_sub_ns()
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
drm/i915: do not disable backlight on vgaswitcheroo switch off
drm/i915: Don't call encoder's get_config unless encoder is active
drm/i915: avoid brightness overflow when doing scale
...
Oleg Nesterov [Fri, 9 Aug 2013 15:19:13 +0000 (17:19 +0200)]
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
device_close()->recalc_sigpending() is not needed, sigprocmask() takes
care of TIF_SIGPENDING correctly.
And without ->siglock it is racy and wrong, it can wrongly clear
TIF_SIGPENDING and miss a signal.
But even with this patch device_close() is still buggy:
1. sigprocmask() should not be used, we have set_task_blocked(),
but this is minor.
2. We should never block SIGKILL or SIGSTOP, and this is what
the code tries to do.
3. This can't protect against SIGKILL or SIGSTOP anyway. Another
thread can do signal_wake_up(), say, do_signal_stop() or
complete_signal() or debugger.
5. device_write() looks equally wrong by the same reason.
Looks like, this tries to protect some wait_event_interruptible() logic
from signals, it should be turned into uninterruptible wait. Or we need
to implement something like signals_stop/start for such a use-case.
Commit "HID: hid-logitech-dj, querying_devices was never set" activate
a flag which guarantees that we do not ask the receiver for too many
enumeration. When the flag is set, each following enumeration call is
discarded (the usb request is not forwarded to the receiver). The flag
is then released when the driver receive a pairing information event,
which normally follows the enumeration request.
However, the USB3 bug makes the driver think the enumeration request
has been forwarded to the receiver. However, it is actually not the
case because the USB stack returns -EPIPE. So, when a new unknown
device appears, the workaround consisting in asking for a new
enumeration is not working anymore: this new enumeration is discarded
because of the flag, which is never reset.
A solution could be to trigger a timeout before releasing it, but for
now, let's just revert the patch.
Michael Neuling [Fri, 9 Aug 2013 07:29:31 +0000 (17:29 +1000)]
powerpc/tm: Fix context switching TAR, PPR and DSCR SPRs
If a transaction is rolled back, the Target Address Register (TAR), Processor
Priority Register (PPR) and Data Stream Control Register (DSCR) should be
restored to the checkpointed values before the transaction began. Any changes
to these SPRs inside the transaction should not be visible in the abort
handler.
Currently Linux doesn't save or restore the checkpointed TAR, PPR or DSCR. If
we preempt a processes inside a transaction which has modified any of these, on
process restore, that same transaction may be aborted we but we won't see the
checkpointed versions of these SPRs.
This adds checkpointed versions of these SPRs to the thread_struct and adds the
save/restore of these three SPRs to the treclaim/trechkpt code.
Without this if any of these SPRs are modified during a transaction, users may
incorrectly see a speculated SPR value even if the transaction is aborted.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> [v3.10] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 9 Aug 2013 07:29:30 +0000 (17:29 +1000)]
powerpc: Save the TAR register earlier
This moves us to save the Target Address Register (TAR) a earlier in
__switch_to. It introduces a new function save_tar() to do this.
We need to save the TAR earlier as we will overwrite it in the transactional
memory reclaim/recheckpoint path. We are going to do this in a subsequent
patch which will fix saving the TAR register when it's modified inside a
transaction.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> [v3.10] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 9 Aug 2013 07:29:29 +0000 (17:29 +1000)]
powerpc: Fix context switch DSCR on POWER8
POWER8 allows the DSCR to be accessed directly from userspace via a new SPR
number 0x3 (Rather than 0x11. DSCR SPR number 0x11 is still used on POWER8 but
like POWER7, is only accessible in HV and OS modes). Currently, we allow this
by setting H/FSCR DSCR bit on boot.
Unfortunately this doesn't work, as the kernel needs to see the DSCR change so
that it knows to no longer restore the system wide version of DSCR on context
switch (ie. to set thread.dscr_inherit).
This clears the H/FSCR DSCR bit initially. If a process then accesses the DSCR
(via SPR 0x3), it'll trap into the kernel where we set thread.dscr_inherit in
facility_unavailable_exception().
We also change _switch() so that we set or clear the H/FSCR DSCR bit based on
the thread.dscr_inherit.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> [v3.10] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 9 Aug 2013 07:29:28 +0000 (17:29 +1000)]
powerpc: Rework setting up H/FSCR bit definitions
This reworks the Facility Status and Control Regsiter (FSCR) config bit
definitions so that we can access the bit numbers. This is needed for a
subsequent patch to fix the userspace DSCR handling.
HFSCR and FSCR bit definitions are the same, so reuse them.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> [v3.10] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Fri, 9 Aug 2013 07:29:27 +0000 (17:29 +1000)]
powerpc: Fix hypervisor facility unavaliable vector number
Currently if we take hypervisor facility unavaliable (from 0xf80/0x4f80) we
mark it as an OS facility unavaliable (0xf60) as the two share the same code
path.
The becomes a problem in facility_unavailable_exception() as we aren't able to
see the hypervisor facility unavailable exceptions.
Below fixes this by duplication the required macros.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> [v3.10] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/kvm/book3s_pr: Return appropriate error when allocation fails
err was overwritten by a previous function call, and checked to be 0. If
the following page allocation fails, 0 is going to be returned instead
of -ENOMEM.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Chen Gang [Mon, 22 Jul 2013 06:32:35 +0000 (14:32 +0800)]
powerpc/kvm: Add signed type cast for comparation
'rmls' is 'unsigned long', lpcr_rmls() will return negative number when
failure occurs, so it need a type cast for comparing.
'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number
when failure occurs, so it need a type cast for comparing.
Signed-off-by: Chen Gang <gang.chen@asianux.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pseries: Fix buffer overflow when reading from pstore
When reading from pstore there is a buffer overflow during decompression
due to the header added in unzip_oops. Remove unzip_oops and call
pstore_decompress directly in nvram_pstore_read. Allocate buffer of size
report_length of the oops header as header will not be deallocated in pstore.
Since we have 'openssl' command line tool to decompress the compressed data,
dump the compressed data in case decompression fails instead of not dumping
anything.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 31 Jul 2013 06:31:26 +0000 (16:31 +1000)]
powerpc: On POWERNV enable PPC_DENORMALISATION by default
We want PPC_DENORMALISATION enabled when POWERNV is enabled,
so update the Kconfig.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: <stable@vger.kernel.org>
Dave Airlie [Thu, 8 Aug 2013 23:09:37 +0000 (09:09 +1000)]
Merge tag 'drm-intel-fixes-2013-08-08' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
A few bugfixes for serious stuff and regressions. Highlight is the
reinstated hack to keep the i915 backlight on when running on an optimus
machine, this prevents black screens especially with some radeon muxed
platforms. And the patch to quiet dmesg on Linus' old mac mini ;-)
* tag 'drm-intel-fixes-2013-08-08' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: do not disable backlight on vgaswitcheroo switch off
drm/i915: Don't call encoder's get_config unless encoder is active
drm/i915: avoid brightness overflow when doing scale
drm/i915: update last_vblank when disabling the power well
drm/i915: fix gen4 digital port hotplug definitions
Curt Brune [Thu, 8 Aug 2013 19:11:03 +0000 (12:11 -0700)]
hwmon: (adt7470) Fix incorrect return code check
In adt7470_write_word_data(), which writes two bytes using
i2c_smbus_write_byte_data(), the return codes are incorrectly AND-ed
together when they should be OR-ed together.
The return code of i2c_smbus_write_byte_data() is zero for success.
The upshot is only the first byte was ever written to the hardware.
The 2nd byte was never written out.
I noticed that trying to set the fan speed limits was not working
correctly on my system. Setting the fan speed limits is the only
code that uses adt7470_write_word_data(). After making the change
the limit settings work and the alarms work also.
Stephen Warren [Tue, 6 Aug 2013 20:38:51 +0000 (14:38 -0600)]
ARM: tegra: unify Tegra's Kconfig a bit more
Move all common select clauses from ARCH_TEGRA_*_SOC to ARCH_TEGRA to
eliminate duplication. The USB-related selects all should have been
common too, but were missing from Tegra114 previously. Move these to
ARCH_TEGRA too. The latter fixes a build break when only Tegra114
support was enabled, but not Tegra20 or Tegra30 support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Linus Torvalds [Thu, 8 Aug 2013 16:38:19 +0000 (09:38 -0700)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o.
Misc ext4 fixes, delayed by Ted moving mail servers and email getting
marked as spam due to bad spf records.
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add WARN_ON to check the length of allocated blocks
ext4: fix retry handling in ext4_ext_truncate()
ext4: destroy ext4_es_cachep on module unload
ext4: make sure group number is bumped after a inode allocation race
Linus Torvalds [Thu, 8 Aug 2013 16:34:04 +0000 (09:34 -0700)]
Merge tag 'regmap-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two things here, one is a fix for a nasty issue where we were failing
to sync the last register in a block when using raw writes and the
other fixes a missing header for the !REGMAP stubs so that we don't
rely on implicit includes in that case"
* tag 'regmap-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add missing header for !CONFIG_REGMAP stubs
regmap: cache: Make sure to sync the last register in a block
Linus Torvalds [Thu, 8 Aug 2013 16:33:27 +0000 (09:33 -0700)]
Merge tag 'spi-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"Just one update for SPI, a simple fix to the davinci driver to correct
the direction for which DMA is mapped following the dmaengine
conversion"
* tag 'spi-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-davinci: Fix direction in dma_map_single()
Linus Torvalds [Thu, 8 Aug 2013 16:32:20 +0000 (09:32 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"More virtio console fixes than I'm happy with, but all real issues,
and all CC:stable.."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-scsi: Fix virtqueue affinity setup
virtio: console: return -ENODEV on all read operations after unplug
virtio: console: fix raising SIGIO after port unplug
virtio: console: clean up port data immediately at time of unplug
virtio: console: fix race in port_fops_open() and port unplug
virtio: console: fix race with port unplug and open/close
virtio/console: Add pipe_lock/unlock for splice_write
virtio/console: Quit from splice_write if pipe->nrbufs is 0
Linus Torvalds [Thu, 8 Aug 2013 16:28:08 +0000 (09:28 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
- MSM: GPIO fixes (includes old code removal)
- OMAP: earlyprintk regression, AM33xx cpgmac PM regression
- OMAP5: urgent fix for potentially harmful voltage regulator values
- Renesas: gpio-keys fix, fix SD card detection, fix shdma calculation
error
- STi: critical SMP boot fix
- tegra: DTS fix for usb-phy
- a couple MAINTAINERS updates
(Arnd is on paternity leave, Kevin is stepping up to help arm-soc
maintenance)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: add TI Keystone ARM platform
MAINTAINERS: delete Srinidhi from ux500
ARM: tegra: enable ULPI phy on Colibri T20
ARM: STi: remove sti_secondary_start from INIT section.
ARM: STi: Fix cpu nodes with correct device_type.
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
ARM: msm: Consolidate gpiomux for older architectures
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
ARM: msm: dts: Fix the gpio register address for msm8960
This commit caused Steven Rostedt's hackbench runs to run out of memory
due to a leak. As noted by Joonsoo Kim, it is buggy in the following
scenario:
"I guess, you may set 0 to all kmem caches's cpu_partial via sysfs,
doesn't it?
In this case, memory leak is possible in following case. Code flow of
possible leak is follwing case.
* in __slab_free()
1. (!new.inuse || !prior) && !was_frozen
2. !kmem_cache_debug && !prior
3. new.frozen = 1
4. after cmpxchg_double_slab, run the (!n) case with new.frozen=1
5. with this patch, put_cpu_partial() doesn't do anything,
because this cache's cpu_partial is 0
6. return
In step 5, leak occur"
And Steven does indeed have cpu_partial set to 0 due to RT testing.
Joonsoo is cooking up a patch, but everybody agrees that reverting this
for now is the right thing to do.
Reported-and-bisected-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clemens Ladisch [Thu, 8 Aug 2013 09:24:55 +0000 (11:24 +0200)]
ALSA: usb-audio: do not trust too-big wMaxPacketSize values
The driver used to assume that the streaming endpoint's wMaxPacketSize
value would be an indication of how much data the endpoint expects or
sends, and compute the number of packets per URB using this value.
However, the Focusrite Scarlett 2i4 declares a value of 1024 bytes,
while only about 88 or 44 bytes are be actually used. This discrepancy
would result in URBs with far too few packets, which would not work
correctly on the EHCI driver.
To get correct URBs, use wMaxPacketSize only as an upper limit on the
packet size.
Reported-by: James Stone <jamesmstone@gmail.com> Tested-by: James Stone <jamesmstone@gmail.com> Cc: <stable@vger.kernel.org> # 2.6.35+ Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Trond Myklebust [Thu, 8 Aug 2013 00:38:07 +0000 (20:38 -0400)]
NFSv4: Fix up nfs4_proc_lookup_mountpoint
Currently, we do not check the return value of client = rpc_clone_client(),
nor do we shut down the resulting cloned rpc_clnt in the case where a
NFS4ERR_WRONGSEC has caused nfs4_proc_lookup_common() to replace the
original value of 'client' (causing a memory leak).
Fix both issues and simplify the code by moving the call to
rpc_clone_client() until after nfs4_proc_lookup_common() has
done its business.
Reported-by: Andy Adamson <andros@netapp.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Michel Dänzer [Wed, 12 Jun 2013 09:58:44 +0000 (11:58 +0200)]
drm: Don't pass negative delta to ktime_sub_ns()
It takes an unsigned value. This happens not to blow up on 64-bit
architectures, but it does on 32-bit, causing
drm_calc_vbltimestamp_from_scanoutpos() to calculate totally bogus
timestamps for vblank events. Which in turn causes e.g. gnome-shell to
hang after a DPMS off cycle with current xf86-video-ati Git.
[airlied: regression introduced in drm: use monotonic time in drm_calc_vbltimestamp_from_scanoutpos]
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59836 Tested-by: shui yangwei <yangweix.shui@intel.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 7 Aug 2013 23:47:02 +0000 (09:47 +1000)]
Merge branch 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux
Some more radeon fixes. Mostly dpm and uvd fixes. Fixes hangs
with dpm on more rv6xx asics, and fixes suspend and resume with UVD.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
Alex Deucher [Tue, 6 Aug 2013 17:34:00 +0000 (13:34 -0400)]
drm/radeon/dpm: require rlc for dpm
The rlc is required for dpm to work properly, so if
the rlc ucode is missing, don't enable dpm. Enabling
dpm without the rlc enabled can result in hangs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / linux-beck.git / log