My test do: fallocate a big file and do write. The file is 512M, but
after file write is done btrfs-debug-tree shows:
item 6 key (257 EXTENT_DATA 0) itemoff 3516 itemsize 53
extent data disk byte 1103101952 nr 536870912
extent data offset 0 nr 399634432 ram 536870912
extent compression 0
Looks like a regression introducted by 6c7d54ac87f338c479d9729e8392eca3f76e11e1, where we set wrong slot.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
you would see long stalls where no work was being done. That is because we were
doing all this extra work to read in the file extent outside of the transaction,
however in the random io case this ends up hurting us because the file extents
are not there to begin with. So axe this logic, since we end up reading in the
file extent when we go to update it anyway. This took the fio job from 11 mb/s
with several ~10 second stalls to 24 mb/s to a couple of 1-2 second stalls.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mounting a bad filesystem caused a BUG_ON(). The following is steps to
reproduce it.
# mkfs.btrfs /dev/sda2
# mount /dev/sda2 /mnt
# mkfs.btrfs /dev/sda1 /dev/sda2
(the program says that /dev/sda2 was mounted, and then exits. )
# umount /mnt
# mount /dev/sda1 /mnt
At the third step, mkfs.btrfs exited in the way of make filesystem. So the
initialization of the filesystem didn't finish. So the filesystem was bad, and
it caused BUG_ON() when mounting it. But BUG_ON() should be called by the wrong
code, not user's operation, so I think it is a bug of btrfs.
This patch fixes it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If you have a disk failure in RAID1 and then add a new disk to the
array, and then try to remove the missing volume, it will fail. The
reason is the sanity check only looks at the total number of rw devices,
which is just 2 because we have 2 good disks and 1 bad one. Instead
check the total number of devices in the array to make sure we can
actually remove the device. Tested this with a failed disk setup and
with this test we can now run
btrfs-vol -r missing /mount/point
and it works fine.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hit this problem while testing RAID1 failure stuff. open_bdev_exclusive
returns ERR_PTR(), not NULL. So change the return value properly. This
is important if you accidently specify a device that doesn't exist when
trying to add a new device to an array, you will panic the box
dereferencing bdev.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a RAID setup has chunks that span multiple disks, and one of those
disks has failed, btrfs_chunk_readonly will return 1 since one of the
disks in that chunk's stripes is dead and therefore not writeable. So
instead if we are in degraded mode, return 0 so we can go ahead and
allocate stuff. Without this patch all of the block groups in a RAID1
setup will end up read-only, which will mean we can't add new disks to
the array since we won't be able to make allocations.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since it introduces this problem where we can run orphan cleanup on a
volume that can have orphan entries re-added. Instead of my original
fix, Yan Zheng pointed out that we can just revert my original fix and
then run the orphan cleanup in open_ctree after we look up the fs_root.
I have tested this with all the tests that gave me problems and this
patch fixes both problems. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can race with the unmount of an fs and the stopping of a kthread where we
will free the block group before we're done using it. The reason for this is
because we do not hold a reference on the block group while its caching, since
the allocator drops its reference once it exits or moves on to the next block
group. This patch fixes the problem by taking a reference to the block group
before we start caching and dropping it when we're done to make sure all
accesses to the block group are safe. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is legal for btrfs_set_acl to be sent a NULL acl. This
makes sure we don't dereference it. A similar patch was sent by
Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently orphan cleanup only ever gets triggered if we cross subvolumes during
a lookup, which means that if we just mount a plain jane fs that has orphans in
it, they will never get cleaned up. This results in panic's like these
where adding an orphan entry results in -EEXIST being returned and we panic. In
order to fix this, we check to see on lookup if our root has had the orphan
cleanup done, and if not go ahead and do it. This is easily reproduceable by
running this testcase
for (i = 0; i < 512; i++)
write(fd2, newdata, 4096);
close(fd2);
i = rename("file2", "file1");
unlink("file1");
}
return 0;
}
and then pulling the power on the box, and then trying to run that test again
when the box comes back up. I've tested this locally and it fixes the problem.
Thanks to Tomas Carnecky for helping me track this down initially.
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix bug reported by Johannes Hirte. The reason of that bug
is btrfs_del_items is called after btrfs_duplicate_item and
btrfs_del_items triggers tree balance. The fix is check that
case and call btrfs_search_slot when needed.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some callers of btrfs_ordered_update_i_size can now pass in
a NULL for the ordered extent to update against. This makes
sure we properly align the offset they pass in when deciding
how much to bump the on disk i_size.
Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When one does a 32-bit readdir(3), the last entry of a directory is
missing. This is however not due to passing a large value to filldir,
but it seems to have to do with glibc doing telldir or something
quirky. In any case, this patch fixes it in practice.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent patch to make fallocate enospc friendly would send
down a NULL trans handle to the allocator. This moves the
transaction start to properly fix things.
Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes us a bit less zealous about making sure we have enough free
metadata space by pearing down the size of new metadata chunks to 256mb instead
of 1gb. Also, we used to try an allocate metadata chunks when allocating data,
but that sort of thing is done elsewhere now so we can just remove it. With my
-ENOSPC test I used to have 3gb reserved for metadata out of 75gb, now I have
1.7gb. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Christoph's patch e244a0aeb6a599c19a7c802cda6e2d67c847b154 doesn't display
the discard option in /proc/mounts, leading to some confusion for me.
Here's the missing bit.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I rebased Christian Parpart's patch to deny hard link across
subvolumes. Original patch modifies also btrfs_rename, but
I excluded it because we can move across subvolumes now and
it make no problem.
-----------------
Hard link across subvolumes should not allowed in Btrfs.
btrfs_link checks root of 'to' directory is same as root
of 'from' file. If not same, btrfs_link returns -EPERM.
Signed-off-by: TARUISI Hiroaki <taruishi.hiroak@jp.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bytes_used field in root item was originally planned to
trace the amount of used data and tree blocks. But it never
worked right since we can't trace freeing of data accurately.
This patch changes it to only trace the amount of tree blocks.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
iput() can trigger new transactions if we are dropping the
final reference, so calling it in btrfs_commit_transaction
may end up deadlock. This patch adds delayed iput to avoid
the issue.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
truncating and deleting regular files are unbound operations,
so it's not good to do them in a single transaction. This
patch makes btrfs_truncate and btrfs_delete_inode start a
new transaction after all items in a tree leaf are deleted.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fallocate(2) may allocate large number of file extents, so it's not
good to do it in a single transaction. This patch make fallocate(2)
start a new transaction for each file extents it allocates.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do log replay in a single transaction, so it's not good to do unbound
operations. This patch cleans up orphan inodes cleanup after replaying
the log. It also avoids doing other unbound operations such as truncating
a file during replaying log. These unbound operations are postponed to
the orphan inode cleanup stage.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are some cases file extents are inserted without involving
ordered struct. In these cases, we update disk_i_size directly,
without checking pending ordered extent and DELALLOC bit. This
patch extends btrfs_ordered_update_i_size() to handle these cases.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
btrfs_duplicate_item duplicates item with new key, guaranteeing
the source item and the new items are in the same tree leaf and
contiguous. It allows us to split file extent in place, without
using lock_extent to prevent bookend extent race.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We allow two log transactions at a time, but use same flag
to mark dirty tree-log btree blocks. So we may flush dirty
blocks belonging to newer log transaction when committing a
log transaction. This patch fixes the issue by using two
flags to mark dirty tree-log btree blocks.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6b0310fbf087ad6 caused a regression resulting in deadlocks
when freezing a filesystem which had active IO; the vfs_check_frozen
level (SB_FREEZE_WRITE) did not let the freeze-related IO syncing
through. Duh.
Changing the test to FREEZE_TRANS should let the normal freeze
syncing get through the fs, but still block any transactions from
starting once the fs is completely frozen.
I tested this by running fsstress in the background while periodically
snapshotting the fs and running fsck on the result. I ran into
occasional deadlocks, but different ones. I think this is a
fine fix for the problem at hand, and the other deadlocky things
will need more investigation.
In general the semantics of IPIs are that they are are expected to
continue functioning after dpm_suspend_noirq().
Specifically I have seen a deadlock between the callfunc IPI and the
stop machine used by xen's do_suspend() routine. If one CPU has already
called dpm_suspend_noirq() then there is a window where it can be sent
a callfunc IPI before all the other CPUs have entered stop_cpu().
If this happens then the first CPU ends up spinning in stop_cpu()
waiting for the other to rendezvous in state STOPMACHINE_PREPARE while
the other is spinning in csd_lock_wait().
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: xen-devel@lists.xensource.com
LKML-Reference: <1280398595-29708-4-git-send-email-ian.campbell@citrix.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use newly introduced netif_notify_peers() method to ensure a gratuitous ARP is
generated after a migration.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: xen-devel@lists.xensource.com Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently such notifications are only generated when the device comes up or the
address changes. However one use case for these notifications is to enable
faster network recovery after a virtual machine migration (by causing switches
to relearn their MAC tables). A migration appears to the network stack as a
temporary loss of carrier and therefore does not trigger either of the current
conditions. Rather than adding carrier up as a trigger (which can cause issues
when interfaces a flapping) simply add an interface which the driver can use
to explicitly trigger the notification.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's currently possible to bypass xattr namespace access rules by
prefixing valid xattr names with "os2.", since the os2 namespace stores
extended attributes in a legacy format with no prefix.
This patch adds checking to deny access to any valid namespace prefix
following "os2.".
This patch fixes a race condition in two utility routines
related to the removal/unlinking of urbs from an anchor.
If two threads are concurrently accessing the same anchor,
both could end up with the same urb - thinking they are
the exclusive owner.
Alan Stern pointed out a related issue in
usb_unlink_anchored_urbs:
"The URB isn't removed from the anchor until it completes
(as a by-product of completion, in fact), which might not
be for quite some time after the unlink call returns.
In the meantime, the subroutine will keep trying to unlink
it, over and over again."
Cc: Oliver Neukum <oneukum@suse.de> Cc: Greg Kroah-Hartman <greg@kroah.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to add a US Interface, Inc. "Navigator" USB device.
Specifically, it's a HAM Radio USB sound modem that also
incorporates three pairs of unique FTDI serial ports. The standard
Linux FTDI serial driver will only recognize the first two serial
ports of an unknown FDTI derived device and this patch adds in
recognition to these specific new IDs.
Signed-off-by: David A. Ranch <dranch@trinnet.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product IDs of Huawei's K3765 and K4505 mobile
broadband usb modems to option.c. It also adds a quirk to the option
probe function so that binding to the device's network interface(class
0xff) is avoided. This is necessary to allow another driver to bind to
that, and to avoid programs like wvdial opening a nonfunctioning tty
during modem discovery.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will
enable support for the Segway Robotic Mobility Platform (RMP200) in the
ftdi_sio kernel module. Currently, users of the Segway RMP200 must use
a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a
udev rule to get the ftdi_sio module to handle the usb interface and
mount it on /dev/ttyXXX. This is not a good solution because some users
will have multiple USB to Serial converters which will use the ftdi_sio
module.
Signed-off-by: John Rogers <jgrogers@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Logitech Harmony 700 series needs an extra delay during
initialization. This patch adds a USB quirk which enables such a delay
and adds the device to the quirks list.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enlarging the buffer size via the MON_IOCT_RING_SIZE ioctl causes
general protection faults. It appears the culprit is an incorrect
argument to mon_free_buff: instead of passing the size of the current
buffer being freed, the size of the new buffer is passed.
Use the correct size argument to mon_free_buff when changing the size of
the buffer.
Signed-off-by: Steven Robertson <steven@strobe.cc> Acked-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC arch/arm/mach-imx/pcm970-baseboard.o
In file included from arch/arm/include/asm/gpio.h:6,
from include/linux/gpio.h:8,
from arch/arm/mach-imx/pcm970-baseboard.c:20:
arch/arm/plat-mxc/include/mach/gpio.h:40: error: expected specifier-qualifier-list before 'spinlock_t'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On versions of the Cortex-A9 prior to r2p0, performing TLB invalidations by
ASID match can result in the incorrect ASID being broadcast to other CPUs.
As a consequence of this, the targetted TLB entries are not invalidated
across the system.
This workaround changes the TLB flushing routines to invalidate entries
regardless of the ASID.
Tested-by: Rob Clark <rob@ti.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On SMP systems, the SMSC911x registers may be accessed by multiple CPUs
and this seems to put the chip in an inconsistent state. The patch adds
spinlocks to the smsc911x_reg_read, smsc911x_reg_write,
smsc911x_rx_readfifo and smsc911x_tx_writefifo functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If signalfd is used to consume a signal generated by a POSIX interval
timer or POSIX message queue, the ssi_int field does not reflect the data
(sigevent->sigev_value) supplied to timer_create(2) or mq_notify(3). (The
ssi_ptr field, however, is filled in.)
This behavior differs from signalfd's treatment of sigqueue-generated
signals -- see the default case in signalfd_copyinfo. It also gives
results that differ from the case when a signal is handled conventionally
via a sigaction-registered handler.
So, set signalfd_siginfo->ssi_int in the remaining cases (__SI_TIMER,
__SI_MESGQ) where ssi_ptr is set.
akpm: a non-back-compatible change. Merge into -stable to minimise the
number of kernels which are in the field and which miss this feature.
Commit a82afdf (block: use the same failfast bits for bio and request)
moved BIO_RW_* bits around such that they match up with REQ_* bits.
Unfortunately, fs.h hard coded RW_MASK, RWA_MASK, READ, WRITE, READA
and SWRITE as 0, 1, 2 and 3, and expected them to match with BIO_RW_*
bits. READ/WRITE didn't change but BIO_RW_AHEAD was moved to bit 4
instead of bit 1, breaking RWA_MASK, READA and SWRITE.
This patch updates RWA_MASK, READA and SWRITE such that they match the
BIO_RW_* bits again. A follow up patch will update the definitions to
directly use BIO_RW_* bits so that this kind of breakage won't happen
again.
Neil also spotted missing RWA_MASK conversion.
Stable: The offending commit a82afdf was released with v2.6.32, so
this patch should be applied to all kernels since then but it must
_NOT_ be applied to kernels earlier than that.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-bisected-by: Vladislav Bolkhovitin <vst@vlnb.net> Root-caused-by: Neil Brown <neilb@suse.de> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In ecryptfs_lookup_and_interpose_lower() the lower mount is not decremented
if allocation of a dentry info struct failed. As a result the lower filesystem
cant be unmounted any more (since it is considered busy). This patch corrects
the reference counting.
Lower filesystems that only implemented unlocked_ioctl weren't being
passed ioctl calls because eCryptfs only checked for
lower_file->f_op->ioctl and returned -ENOTTY if it was NULL.
eCryptfs shouldn't implement ioctl(), since it doesn't require the BKL.
This patch introduces ecryptfs_unlocked_ioctl() and
ecryptfs_compat_ioctl(), which passes the calls on to the lower file
system.
The cgroup device whitelist code gets confused when trying to grant
permission to a disk partition that is not currently open. Part of
blkdev_open() includes __blkdev_get() on the whole disk.
Basically, the only ways to reliably allow a cgroup access to a partition
on a block device when using the whitelist are to 1) also give it access
to the whole block device or 2) make sure the partition is already open in
a different context.
The patch avoids the cgroup check for the whole disk case when opening a
partition.
If the 'bio_split' path in raid10-read is used while
resync/recovery is happening it is possible to deadlock.
Fix this be elevating ->nr_waiting for the duration of both
parts of the split request.
This fixes a bug that has been present since 2.6.22
but has only started manifesting recently for unknown reasons.
It is suitable for and -stable since then.
ide_cd_error_cmd() can complete an erroneous request with leftover
buffers. Signal this with its return value so that the request is not
accessed after its completion in the irq handler and we oops.
Signed-off-by: Borislav Petkov <bp@alien8.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a build failure "error: void value not ignored as it ought to be"
by removing an assignment of a void return value. The functionality of
the code is not changed.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Acked-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SPLICE_F_NONBLOCK is clearly documented to only affect blocking on the
pipe. In __generic_file_splice_read(), however, it causes an EAGAIN
if the page is currently being read.
This makes it impossible to write an application that only wants
failure if the pipe is full. For example if the same process is
handling both ends of a pipe and isn't otherwise able to determine
whether a splice to the pipe will fill it or not.
We could make the read non-blocking on O_NONBLOCK or some other splice
flag, but for now this is the simplest fix.
This patch uses an RCU-inspired approach to fix it. In the RX tasklet's
find_vcc() function we first refuse to use a VCC which already has the
ATM_VF_READY bit cleared. And in the VCC close function, we synchronise
with the tasklet to ensure that it can't still be using the VCC before
we continue and allow the VCC to be destroyed.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Nathan Williams <nathan@traverse.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI delivery from on-board ahci controller doesn't work on K8M800. At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge. Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.
There is no reason to run NVidia-specific quirks related to HT MSI
mappings with MSI disabled via pci=nomsi, so make
__nv_msi_ht_cap_quirk() return immediately in that case.
This allows at least one machine to boot 100% of the time with
pci=nomsi (it still doesn't boot reliably without that).
This patch prevents the code from calling parport_release and
parport_unregister_device twice with the same arguments - and thus fixes an oops.
Rationale:
After the first call the parport is already released and the
handle isn't valid anymore and calling parport_release and
parport_unregister_device twice isn't a good idea.
When running on VMware's platform, we have seen situations where
the AP's try to calibrate the lpj values and fail to get good calibration
runs becasue of timing issues. As a result delays don't work correctly
on all cpus.
The solutions is to set preset_lpj value based on the current tsc frequency
value. This is similar to what KVM does as well.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
LKML-Reference: <1280790637.14933.29.camel@ank32.eng.vmware.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xchg() and cmpxchg() modify their memory operands, not merely read
them. For some versions of gcc the "memory" clobber has apparently
dealt with the situation, but not for all.
Originally-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Glauber Costa <glommer@redhat.com> Cc: Avi Kivity <avi@redhat.com> Cc: Peter Palfrader <peter@palfrader.org> Cc: Greg KH <gregkh@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Zachary Amsden <zamsden@redhat.com> Cc: Marcelo Tosatti <mtosatti@redhat.com>
LKML-Reference: <4C4F7277.8050306@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In nvram_write, first of all, correctly handle the case where the file
pointer is already beyond the end; we should return EOF in that case.
Second, make the logic a bit more explicit so that gcc can statically
prove that the copy_from_user() is safe. Once the condition of the
beyond-end filepointer is eliminated, the copy is safe but gcc can't
prove it, causing build failures for i386 allyesconfig.
Third, eliminate the entirely superfluous variable "len", and just use
the passed-in variable "count" instead.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Arjan van de Ven <arjan@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <tip-*@git.kernel.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Backlund reported that the powerpc build broke with make 3.82.
It failed with the following message:
arch/powerpc/Makefile:183: *** mixed implicit and normal rules. Stop.
The fix is to avoid mixing non-wildcard and wildcard targets.
Reported-by: Thomas Backlund <tmb@mandriva.org> Tested-by: Thomas Backlund <tmb@mandriva.org> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SIDPR window registers are shared across ports and as each access is
done in two steps, accesses to different ports under EH may race.
This primarily is caused by incorrect host locking in EH context and
should be fixed by defining locking requirements for each EH operation
which can be used during EH and enforcing them but for now work around
the problem by adding a dedicated SIDPR lock and grabbing it for each
SIDPR access.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mark Knecht <markknecht@gmail.com> Reported-by: Paul Check <paul@thechecks.ca> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In kernel Bugzilla #15825 (2 users), in a wireless mailing list thread
(http://lists.infradead.org/pipermail/b43-dev/2010-May/000124.html), and on a
netbook owned by John Linville
(http://marc.info/?l=linux-wireless&m=127230751408818&w=4), there are reports
of ssb failing to detect an SPROM at the normal location. After studying the
MMIO trace dump for the Broadcom wl driver, it was determined that the affected
boxes had a relocated SPROM.
This patch fixes all systems that have reported this problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BUG: unable to handle kernel NULL pointer dereference at 00000010
IP: [<c1266c36>] ssb_is_sprom_available+0x16/0x30
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes. At least some b43 devices are 'in the wild' that
don't have SPROMs at all. When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.
This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it. This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus. The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Michael Buesch <mb@bu3sch.de> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some laptops there is no HDMI/DP. But the xrandr still reports
several disconnected HDMI/display ports. In such case the user will be
confused.
>DVI1 disconnected (normal left inverted right x axis y axis)
>DP1 disconnected (normal left inverted right x axis y axis)
>DVI2 disconnected (normal left inverted right x axis y axis)
>DP2 disconnected (normal left inverted right x axis y axis)
>DP3 disconnected (normal left inverted right x axis y axis)
This patch set is to use the child device parsed in VBT to decide whether
the HDMI/DP/LVDS/TV should be initialized.
Parse the child device from VBT.
The device class type is also added for LFP, TV, HDMI, DP output.
Acked-by: Takashi Iwai <tiwai@suse.de> Cc: Matthew Garrett <mjg@redhat.com> Cc: Adam Jackson <ajax@redhat.com> Cc: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xen_sched_clock only counts unstolen time. In principle this should
be useful to the Linux scheduler so that it knows how much time a process
actually consumed. But in practice this doesn't work very well as the
scheduler expects the sched_clock time to be synchronized between
cpus. It also uses sched_clock to measure the time a task spends
sleeping, in which case "unstolen time" isn't meaningful.
So just use plain xen_clocksource_read to return wallclock nanoseconds
for sched_clock.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the __exit mark from cifs_exit_dns_resolver() as it's called by the
module init routine in case of error, and so may have been discarded during
linkage.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a kernel Oops in the GFS2 rename code.
The problem was in the way the gfs2 directory code was trying
to re-use sentinel directory entries.
In the failing case, gfs2's rename function was renaming a
file to another name that had the same non-trivial length.
The file being renamed happened to be the first directory
entry on the leaf block.
First, the rename code (gfs2_rename in ops_inode.c) found the
original directory entry and decided it could do its job by
simply replacing the directory entry with another. Therefore
it determined correctly that no block allocations were needed.
Next, the rename code deleted the old directory entry prior to
replacing it with the new name. Therefore, the soon-to-be
replaced directory entry was temporarily made into a directory
entry "sentinel" or a place holder at the start of a leaf block.
Lastly, it went to re-add the replacement directory entry in
that leaf block. However, when gfs2_dirent_find_space was
looking for space in the leaf block, it used the wrong value
for the sentinel. That threw off its calculations so later
it decides it can't really re-use the sentinel and therefore
must allocate a new leaf block. But because it previously decided
to re-use the directory entry, it didn't waste the time to
grab a new block allocation for the inode. Therefore, the
inode's i_alloc pointer was still NULL and it crashes trying to
reference it.
In the case of sentinel directory entries, the entire dirent is
reused, not just the "free space" portion of it, and therefore
the function gfs2_dirent_find_space should use the value 0
rather than GFS2_DIRENT_SIZE(0) for the actual dirent size.
Fixing this calculation enables the reproducer programs to work
properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch prevents user "foo" from using the SWAPEXT ioctl to swap
a write-only file owned by user "bar" into a file owned by "foo" and
subsequently reading it. It does so by checking that the file
descriptors passed to the ioctl are also opened for reading.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When kernel-internal users use cfg80211_get_bss()
to get a reference to a BSS struct, they may end
up getting one that would have been removed from
the list if there had been any userspace access
to the list. This leads to inconsistencies and
problems.
Fix it by making cfg80211_get_bss() ignore BSSes
that cfg80211_bss_expire() would remove.
Ever since mac80211/drivers are no longer
fully in charge of keeping track of the
auth status, trying to make them do so will
fail. Instead of warning and reporting the
deauthentication to userspace, cfg80211 must
simply ignore it so that spurious
deauthentications, e.g. before starting
authentication, aren't seen by userspace as
actual deauthentications.
Reported-by: Paul Stewart <pstew@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix possible double priv->mutex lock introduced by commit a69b03e941abae00380fc6bc1877fb797a1b31e6
"iwlwifi: cancel scan watchdog in iwl_bg_abort_scan" .
We can not call cancel_delayed_work_sync(&priv->scan_check) with
priv->mutex locked because workqueue function iwl_bg_scan_check()
take that lock internally.
We do not need to synchronize when canceling priv->scan_check work.
We can avoid races (sending double abort command or send no
command at all) using STATUS_SCAN_ABORT bit. Moreover
current iwl_bg_scan_check() code seems to be broken, as
we should not send abort commands when currently aborting.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Björn Smedman <bjorn.smedman@venatech.se> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log