Barry Song [Thu, 16 May 2013 06:08:07 +0000 (14:08 +0800)]
ASoC: omap-hdmi-codec: make the driver common for other SoCs
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown [Sat, 1 Jun 2013 22:13:53 +0000 (23:13 +0100)]
ASoC: pcm: Require both CODEC and CPU support when declaring stream caps
When declaring playback and capture capabilities check for both CODEC
side and CPU side support rather than only checking for CODEC side
support. While it is unusual some CPUs do have unidirectional DAIs.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
arch/blackfin/mach-bf533/boards/stamp.c:545:2: error: operator '||' has no right operand
arch/blackfin/mach-bf533/boards/stamp.c:662:3: error: 'bfin_snd_resources' undeclared here (not in a function)
arch/blackfin/mach-bf533/boards/stamp.c:662:3: error: negative width in bit-field '<anonymous>'
arch/blackfin/mach-bf533/boards/stamp.c:665:21: error: 'bfin_snd_data' undeclared here (not in a function)
make[4]: *** [arch/blackfin/mach-bf533/boards/stamp.o] Error 1
Introduced by commit 15502e0ca0da651b48c7def2983e7bb464349b2a ("blackfin:
Remove references to the bf5x_tdm driver"), which removed two config
options, but only one "||".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@linaro.org>
Linus Torvalds [Sat, 1 Jun 2013 21:24:54 +0000 (06:24 +0900)]
Merge branch 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This patcheset includes fixes for:
- the PCI/LBA which brings back the stifb graphics framebuffer
console
- possible memory overflows in parisc kernel init code
- parport support on older GSC machines
- avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
- MAINTAINERS file list updates for parisc."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
Helge Deller [Thu, 30 May 2013 21:06:39 +0000 (21:06 +0000)]
parisc: parport0: fix this legacy no-device port driver!
Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Helge Deller [Thu, 30 May 2013 16:24:46 +0000 (16:24 +0000)]
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.
In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Helge Deller [Fri, 31 May 2013 22:24:58 +0000 (22:24 +0000)]
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
commit dc7dce280a
Author: Bjorn Helgaas <bhelgaas@google.com>
Date: Fri Oct 28 16:27:27 2011 -0600
parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
resources
Supply root bus resources to pci_create_root_bus() so they're correct
immediately. This fixes the problem of "early" and "header" quirks seeing
incorrect root bus resources.
added tests for elmmio_space.start while it should use
elmmio_space.flags. This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.
LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Bjorn Helgaas [Thu, 30 May 2013 17:45:39 +0000 (11:45 -0600)]
parisc/PCI: Set type for LBA bus_num resource
The non-PAT resource probing code failed to set the type of the LBA bus_num
resource (30aa80da43 "parisc/PCI: register busn_res for root buses" did
the corresponding thing for the PAT case).
This causes incorrect resource assignments and a non-working stifb
framebuffer on most parisc machines.
Paul Bolle [Wed, 29 May 2013 09:56:58 +0000 (09:56 +0000)]
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
There's a Makefile line setting cflags for CONFIG_PA7100. But that
Kconfig macro doesn't exist. There is a Kconfig symbol PA7000, which
covers both PA7000 and PA7100 processors. So let's use the corresponding
Kconfig macro.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Tue, 28 May 2013 20:35:54 +0000 (20:35 +0000)]
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
With CONFIG_DISCONTIGMEM=y and multiple physical memory areas,
cat /proc/kpageflags triggers this kernel bug:
kernel BUG at arch/parisc/include/asm/mmzone.h:50!
CPU: 2 PID: 7848 Comm: cat Tainted: G D W 3.10.0-rc3-64bit #44
IAOQ[0]: kpageflags_read0x128/0x238
IAOQ[1]: kpageflags_read0x12c/0x238
RP(r2): proc_reg_read0xbc/0x130
Backtrace:
[<00000000402ca2d4>] proc_reg_read0xbc/0x130
[<0000000040235bcc>] vfs_read0xc4/0x1d0
[<0000000040235f0c>] SyS_read0x94/0xf0
[<0000000040105fc0>] syscall_exit0x0/0x14
kpageflags_read() walks through the whole memory, even if some memory
areas are physically not available. So, we should better not BUG on an
unavailable pfn in pfn_to_nid() but just return the expected value -1 or
0.
Linus Torvalds [Sat, 1 Jun 2013 11:13:16 +0000 (20:13 +0900)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few more fixes for powerpc 3.10. It's a bit more than I
would have liked this late in the game but I suppose that's what
happens with a brand new chip generation coming out.
A few regression fixes, some last minute fixes for new P8 features
such as transactional memory,...
There's also one powerpc KVM patch that I requested that adds two
missing functions to our in-kernel interrupt controller support which
is itself a new 3.10 feature. These are defined by the base
hypervisor specification. We didn't implement them originally because
Linux doesn't use them but they are simple and I'm not comfortable
having a half-implemented interface in 3.10 and having to deal with
versionning etc... later when something starts needing those calls.
They cannot be emulated in qemu when using in-kernel interrupt
controller (not enough shared state).
Just added a last minute patch to fix a typo introducing a breakage in
our cputable for Power7+ processors, sorry about that, but the
regression it fixes just hurt me :-)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/cputable: Fix typo on P7+ cputable entry
powerpc/perf: Add missing SIER support
powerpc/perf: Revert to original NO_SIPR logic
powerpc/pci: Remove the unused variables in pci_process_bridge_OF_ranges
powerpc/pci: Remove the stale comments of pci_process_bridge_OF_ranges
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
powerpc/32bit:Store temporary result in r0 instead of r8
powerpc/mm: Always invalidate tlb on hpte invalidate and update
powerpc/pseries: Improve stream generation comments in copypage/user
powerpc/pseries: Kill all prefetch streams on context switch
powerpc/cputable: Fix oprofile_cpu_type on power8
powerpc/mpic: Fix irq distribution problem when MPIC_SINGLE_DEST_CPU
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
powerpc/tm: Move TM abort cause codes to uapi
powerpc/tm: Abort on emulation and alignment faults
powerpc/tm: Update cause codes documentation
powerpc/tm: Make room for hypervisor in abort cause codes
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
Linus Torvalds [Sat, 1 Jun 2013 10:55:26 +0000 (19:55 +0900)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock subsystem fixes from Mike Turquette:
"A mix of small fixes affecting mostly ARM platforms as well as a
discrete clock expander chip. Most fixes are corrections to lousy
clock data of one form or another."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: Include clk mxs header file
clk: vt8500: Fix unbalanced spinlock in vt8500_dclk_set_rate()
clk: si5351: Set initial clkout rate when defined in platform data.
clk: si5351: Fix clkout rate computation.
clk: samsung: Add CLK_IGNORE_UNUSED flag for the sysreg clocks
clk: ux500: clk-sysctrl: handle clocks with no parents
clk: ux500: Provide device enumeration number suffix for SMSC911x
Linus Torvalds [Sat, 1 Jun 2013 10:51:52 +0000 (19:51 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull assorted fixes from Al Viro:
"There'll be more - I'm trying to dig out from under the pile of mail
(a couple of weeks of something flu-like ;-/) and there's several more
things waiting for review; this is just the obvious stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
zoran: racy refcount handling in vm_ops ->open()/->close()
befs_readdir(): do not increment ->f_pos if filldir tells us to stop
hpfs: deadlock and race in directory lseek()
qnx6: qnx6_readdir() has a braino in pos calculation
fix buffer leak after "scsi: saner replacements for ->proc_info()"
vfs: Fix invalid ida_remove() call
Linus Torvalds [Sat, 1 Jun 2013 10:48:59 +0000 (19:48 +0900)]
Merge tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull two NFS client fixes from Trond Myklebust:
- Fix a regression that broke NFS mounting using klibc and busybox
- Stable fix to check access modes correctly on NFSv4 delegated open()
* tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix security flavor negotiation with legacy binary mounts
NFSv4: Fix a thinko in nfs4_try_open_cached
Will Schmidt [Mon, 20 May 2013 05:04:18 +0000 (05:04 +0000)]
powerpc/cputable: Fix typo on P7+ cputable entry
Fix a typo in setting COMMON_USER2_POWER7 bits to .cpu_user_features2
cpu specs table.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Srivatsa S. Bhat [Tue, 21 May 2013 09:32:48 +0000 (09:32 +0000)]
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:
CC arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.
Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.
Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de> Cc: stable@vger.kernel.org Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Thu, 23 May 2013 15:42:21 +0000 (15:42 +0000)]
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X. H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state. H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor. Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.
These hcalls are not currently used by Linux guests, but may be in
future.
Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While returning from exception handling in case of PREEMPT enabled,
_TIF_NEED_RESCHED bit is checked in TI_FLAGS (thread_info flag) of current
task. Only if this bit is set, it should continue with the process of
calling preempt_schedule_irq() to schedule highest priority task if
available.
Current code assumes that r8 contains TI_FLAGS and check this for
_TIF_NEED_RESCHED, but as r8 is modified in the code which executes before
this check, r8 no longer contains the expected TI_FLAGS information.
As a result check for comparison with _TIF_NEED_RESCHED was failing even if
NEED_RESCHED bit is set in the current thread_info flag. Due to this,
preempt_schedule_irq() and in turn scheduler was not getting called even if
highest priority task is ready for execution.
So, store temporary results in r0 instead of r8 to prevent r8 from getting
modified as subsequent code is dependent on its value.
powerpc/mm: Always invalidate tlb on hpte invalidate and update
If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate.
Michael Neuling [Wed, 29 May 2013 19:34:27 +0000 (19:34 +0000)]
powerpc/pseries: Kill all prefetch streams on context switch
On context switch, we should have no prefetch streams leak from one
userspace process to another. This frees up prefetch resources for the
next process.
Based on patch from Milton Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Maynard informed me that neither the oprofile kernel module nor oprofile
userspace has been updated to support that "legacy" oprofile module
interface for power8, which is indicated by "ppc64/power8." This results
in no samples. The solution is to default to the "timer" type, instead.
The raw entry also should be updated, as "ppc64/ibm-compat-v1" indicates
to oprofile userspace to use "compatibility events" which are obsolete
in ISA 2.07.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Sun, 26 May 2013 18:09:41 +0000 (18:09 +0000)]
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> # v3.9 Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Sun, 26 May 2013 18:09:39 +0000 (18:09 +0000)]
powerpc/tm: Abort on emulation and alignment faults
If we are emulating an instruction inside an active user transaction that
touches memory, the kernel can't emulate it as it operates in transactional
suspend context. We need to abort these transactions and send them back to
userspace for the hardware to rollback.
We can service these if the user transaction is in suspend mode, since the
kernel will operate in the same suspend context.
This adds a check to all alignment faults and to specific instruction
emulations (only string instructions for now). If the user process is in an
active (non-suspended) transaction, we abort the transaction go back to
userspace allowing the HW to roll back the transaction and tell the user of the
failure. This also adds new tm abort cause codes to report the reason of the
persistent error to the user.
Crappy test case here http://neuling.org/devel/junkcode/aligntm.c
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> # v3.9 Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Sun, 26 May 2013 18:09:38 +0000 (18:09 +0000)]
powerpc/tm: Update cause codes documentation
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> # 3.9 only Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Sun, 26 May 2013 18:09:37 +0000 (18:09 +0000)]
powerpc/tm: Make room for hypervisor in abort cause codes
PAPR carves out 0xff-0xe0 for hypervisor use of transactional memory software
abort cause codes. Unfortunately we don't respect this currently.
Below fixes this to move our cause codes to below this region.
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: <stable@vger.kernel.org> # 3.9 only Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Fri, 31 May 2013 21:59:14 +0000 (06:59 +0900)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull reiserfs fixes from Jan Kara:
"Three reiserfs fixes. They fix real problems spotted by users so I
hope they are ok even at this stage."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: fix deadlock with nfs racing on create/lookup
reiserfs: fix problems with chowning setuid file w/ xattrs
reiserfs: fix spurious multiple-fill in reiserfs_readdir_dentry
Linus Torvalds [Fri, 31 May 2013 21:56:21 +0000 (06:56 +0900)]
Merge tag 'for-linus-v3.10-rc4-crc-xattr-fixes' of git://oss.sgi.com/xfs/xfs
Pull xfs extended attribute fixes for CRCs from Ben Myers:
"Here are several fixes that are relevant on CRC enabled XFS
filesystems. They are followed by a rework of the remote attribute
code so that each block of the attribute contains a header with a CRC.
Previously there was a CRC header per extent in the remote attribute
code, but this was untenable because it was not possible to know how
many extents would be allocated for the attribute until after the
allocation has completed, due to the fragmentation of free space.
This became complicated because the size of the headers needs to be
added to the length of the payload to get the overall length required
for the allocation. With a header per block, things are less
complicated at the cost of a little space.
I would have preferred to defer this and the rest of the CRC queue to
3.11 to mitigate risk for existing non-crc users in 3.10. Doing so
would require setting a feature bit for the on-disk changes, and so I
have been pressured into sending this pull request by Eric Sandeen and
David Chinner from Red Hat. I'll send another pull request or two
with the rest of the CRC queue next week.
- Remove assert on count of remote attribute CRC headers
- Fix the number of blocks read in for remote attributes
- Zero remote attribute tails properly
- Fix mapping of remote attribute buffers to have correct length
- initialize temp leaf properly in xfs_attr3_leaf_unbalance, and
xfs_attr3_leaf_compact
- Rework remote atttributes to have a header per block"
* tag 'for-linus-v3.10-rc4-crc-xattr-fixes' of git://oss.sgi.com/xfs/xfs:
xfs: rework remote attr CRCs
xfs: fully initialise temp leaf in xfs_attr3_leaf_compact
xfs: fully initialise temp leaf in xfs_attr3_leaf_unbalance
xfs: correctly map remote attr buffers during removal
xfs: remote attribute tail zeroing does too much
xfs: remote attribute read too short
xfs: remote attribute allocation may be contiguous
Linus Torvalds [Fri, 31 May 2013 21:50:16 +0000 (06:50 +0900)]
Merge tag 'for-linus-v3.10-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs fixes from Ben Myers:
- Fix nested transactions in xfs_qm_scall_setqlim
- Clear suid/sgid bits when we truncate with size update
- Fix recovery for split buffers
- Fix block count on remote symlinks
- Add fsgeom flag for v5 superblock support
- Disable XFS_IOC_SWAPEXT for CRC enabled filesystems
- Fix dirv3 freespace block corruption
* tag 'for-linus-v3.10-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: fix dir3 freespace block corruption
xfs: disable swap extents ioctl on CRC enabled filesystems
xfs: add fsgeom flag for v5 superblock support.
xfs: fix incorrect remote symlink block count
xfs: fix split buffer vector log recovery support
xfs: kill suid/sgid through the truncate path.
xfs: avoid nesting transactions in xfs_qm_scall_setqlim()
Linus Torvalds [Fri, 31 May 2013 21:45:10 +0000 (06:45 +0900)]
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Module compilation issues (symbol not exported).
- Plug a hole where user space can bring the kernel down.
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: don't kill the kernel on a bad esr from el0
arm64: treat unhandled compat el0 traps as undef
arm64: Do not report user faults for handled signals
arm64: kernel: compiling issue, need 'EXPORT_SYMBOL(clear_page)'
Jeff Mahoney [Fri, 31 May 2013 19:51:17 +0000 (15:51 -0400)]
reiserfs: fix deadlock with nfs racing on create/lookup
Reiserfs is currently able to be deadlocked by having two NFS clients
where one has removed and recreated a file and another is accessing the
file with an open file handle.
If one client deletes and recreates a file with timing such that the
recreated file obtains the same [dirid, objectid] pair as the original
file while another client accesses the file via file handle, the create
and lookup can race and deadlock if the lookup manages to create the
in-memory inode first.
The create thread, in insert_inode_locked4, will hold the write lock
while waiting on the other inode to be unlocked. The lookup thread,
anywhere in the iget path, will release and reacquire the write lock while
it schedules. If it needs to reacquire the lock while the create thread
has it, it will never be able to make forward progress because it needs
to reacquire the lock before ultimately unlocking the inode.
This patch drops the write lock across the insert_inode_locked4 call so
that the ordering of inode_wait -> write lock is retained. Since this
would have been the case before the BKL push-down, this is safe.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jeff Mahoney [Fri, 31 May 2013 19:54:17 +0000 (15:54 -0400)]
reiserfs: fix problems with chowning setuid file w/ xattrs
reiserfs_chown_xattrs() takes the iattr struct passed into ->setattr
and uses it to iterate over all the attrs associated with a file to change
ownership of xattrs (and transfer quota associated with the xattr files).
When the setuid bit is cleared during chown, ATTR_MODE and iattr->ia_mode
are passed to all the xattrs as well. This means that the xattr directory
will have S_IFREG added to its mode bits.
This has been prevented in practice by a missing IS_PRIVATE check
in reiserfs_acl_chmod, which caused a double-lock to occur while holding
the write lock. Since the file system was completely locked up, the
writeout of the corrupted mode never happened.
This patch temporarily clears everything but ATTR_UID|ATTR_GID for the
calls to reiserfs_setattr and adds the missing IS_PRIVATE check.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jeff Mahoney [Fri, 31 May 2013 19:07:52 +0000 (15:07 -0400)]
reiserfs: fix spurious multiple-fill in reiserfs_readdir_dentry
After sleeping for filldir(), we check to see if the file system has
changed and research. The next_pos pointer is updated but its value
isn't pushed into the key used for the search itself. As a result,
the search returns the same item that the last cycle of the loop did
and filldir() is called multiple times with the same data.
The end result is that the buffer can contain the same name multiple
times. This can be returned to userspace or used internally in the
xattr code where it can manifest with the following warning:
jdm-20004 reiserfs_delete_xattrs: Couldn't delete all xattrs (-2)
reiserfs_for_each_xattr uses reiserfs_readdir_dentry to iterate over
the xattr names and ends up trying to unlink the same name twice. The
second attempt fails with -ENOENT and the error is returned. At some
point I'll need to add support into reiserfsck to remove the orphaned
directories left behind when this occurs.
The fix is to push the value into the key before researching.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz>
Al Viro [Thu, 23 May 2013 08:38:22 +0000 (04:38 -0400)]
zoran: racy refcount handling in vm_ops ->open()/->close()
worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Richard Genoud [Fri, 31 May 2013 15:49:35 +0000 (15:49 +0000)]
atmel_lcdfb: blank the backlight on remove
When removing atmel_lcdfb module, the backlight is unregistered but not
blanked. (only for CONFIG_BACKLIGHT_ATMEL_LCDC case).
This can result in the screen going full white depending on how the PWM
is wired.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Al Viro [Sat, 18 May 2013 06:38:52 +0000 (02:38 -0400)]
hpfs: deadlock and race in directory lseek()
For one thing, there's an ABBA deadlock on hpfs fs-wide lock and i_mutex
in hpfs_dir_lseek() - there's a lot of methods that grab the former with
the caller already holding the latter, so it must take i_mutex first.
For another, locking the damn thing, carefully validating the offset,
then dropping locks and assigning the offset is obviously racy.
Moreover, we _must_ do hpfs_add_pos(), or the machinery in dnode.c
won't modify the sucker on B-tree surgeries.
Al Viro [Fri, 17 May 2013 19:21:56 +0000 (15:21 -0400)]
qnx6: qnx6_readdir() has a braino in pos calculation
We want to mask lower 5 bits out, not leave only those and clear the
rest... As it is, we end up always starting to read from the beginning
of directory, no matter what the current position had been.
Takashi Iwai [Fri, 10 May 2013 12:04:11 +0000 (14:04 +0200)]
vfs: Fix invalid ida_remove() call
When the group id of a shared mount is not allocated, the umount still
tries to call mnt_release_group_id(), which eventually hits a kernel
warning at ida_remove() spewing a message like:
ida_remove called for id=0 which is not allocated.
This patch fixes the bug simply checking the group id in the caller.
Mark Rutland [Tue, 28 May 2013 14:54:15 +0000 (15:54 +0100)]
arm64: don't kill the kernel on a bad esr from el0
Rather than completely killing the kernel if we receive an esr value we
can't deal with in the el0 handlers, send the process a SIGILL and log
the esr value in the hope that we can debug it. If we receive a bad esr
from el1, we'll die() as before.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: stable@vger.kernel.org
Mark Rutland [Fri, 24 May 2013 11:02:35 +0000 (12:02 +0100)]
arm64: treat unhandled compat el0 traps as undef
Currently, if a compat process reads or writes from/to a disabled
cp15/cp14 register, the trap is not handled by the el0_sync_compat
handler, and the kernel will head to bad_mode, where it will die(), and
oops(). For 64 bit processes, disabled system register accesses are
currently treated as unhandled instructions.
This patch modifies entry.S to treat these unhandled traps as undefined
instructions, sending a SIGILL to userspace. This gives processes a
chance to handle this and stop using inaccessible registers, and
prevents further issues in the kernel as a result of the die().
Reported-by: Johannes Jensen <Johannes.Jensen@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the introduction of target_get_sess_cmd() referencing counting for
ISCSI_OP_SCSI_CMD processing with iser-target, iscsit_free_cmd() usage
in traditional iscsi-target driver code now needs to be aware of the
active I/O shutdown case when a remaining se_cmd->cmd_kref reference may
exist after transport_generic_free_cmd() completes, requiring a final
target_put_sess_cmd() to release iscsi_cmd descriptor memory.
This patch changes iscsit_free_cmd() to invoke __iscsit_free_cmd() before
transport_generic_free_cmd() -> target_put_sess_cmd(), and also avoids
aquiring the per-connection queue locks for typical fast-path calls
during normal ISTATE_REMOVE operation.
Also update iscsit_free_cmd() usage throughout iscsi-target to
use the new 'bool shutdown' parameter.
This patch fixes a regression bug introduced during v3.10-rc1 in
commit 3e1c81a95, that was causing the following WARNING to appear:
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
Go ahead and propigate up the ->cmd_kref put return value from
target_put_sess_cmd() -> transport_release_cmd() -> transport_put_cmd()
-> transport_generic_free_cmd().
This is useful for certain fabrics when determining the active I/O
shutdown case with SCF_ACK_KREF where a final target_put_sess_cmd()
is still required by the caller.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Fri, 31 May 2013 06:04:05 +0000 (16:04 +1000)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One qxl 32-bit warning fix, the rest is a bunch of radeon fixes from
Alex for some issues we've been seeing."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/qxl: fix build warnings on 32-bit
radeon: use max_bus_speed to activate gen2 speeds
drm/radeon: narrow scope of Apple re-POST hack
drm/radeon: don't check crtcs in card_posted() on cards without DCE
drm/radeon: fix card_posted check for newer asics
drm/radeon: fix typo in cu_per_sh on verde
drm/radeon: UVD block on SUMO2 is the same as on SUMO
Fabio Estevam [Mon, 27 May 2013 15:28:25 +0000 (12:28 -0300)]
clk: mxs: Include clk mxs header file
Fix the following sparse warnings:
drivers/clk/mxs/clk-imx28.c:72:5: warning: symbol 'mxs_saif_clkmux_select' was not declared. Should it be static?
drivers/clk/mxs/clk-imx28.c:156:12: warning: symbol 'mx28_clocks_init' was not declared. Should it be static?
Kees Cook [Thu, 23 May 2013 17:32:17 +0000 (10:32 -0700)]
iscsi-target: fix heap buffer overflow on error
If a key was larger than 64 bytes, as checked by iscsi_check_key(), the
error response packet, generated by iscsi_add_notunderstood_response(),
would still attempt to copy the entire key into the packet, overflowing
the structure on the heap.
Remote preauthentication kernel memory corruption was possible if a
target was configured and listening on the network.
CVE-2013-2850
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Fri, 31 May 2013 00:48:56 +0000 (09:48 +0900)]
Merge branch 'for-3.10' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"A couple minor fixes for the (new to 3.10) gss-proxy code.
And one regression from user-namespace changes. (XBMC clients were
doing something admittedly weird--sending -1 gid's--but something that
we used to allow.)"
* 'for-3.10' of git://linux-nfs.org/~bfields/linux:
svcrpc: fix failures to handle -1 uid's and gid's
svcrpc: implement O_NONBLOCK behavior for use-gss-proxy
svcauth_gss: fix error code in use_gss_proxy()
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
This patch fixes a bug where FILEIO was incorrectly reporting the number
of logical blocks (+ 1) when using non struct block_device export mode.
It changes fd_get_blocks() to follow all other backend ->get_blocks() cases,
and reduces the calculated dev_size by one dev->dev_attrib.block_size
number of bytes, and also fixes initial fd_block_size assignment at
fd_configure_device() time introduced in commit 0fd97ccf4.
Linus Torvalds [Fri, 31 May 2013 00:44:10 +0000 (09:44 +0900)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
- Three EFI-related fixes
- Two early memory initialization fixes
- build fix for older binutils
- fix for an eager FPU performance regression -- currently we don't
allow the use of the FPU at interrupt time *at all* in eager mode,
which is clearly wrong.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Allow FPU to be used at interrupt time even with eagerfpu
x86, crc32-pclmul: Fix build with older binutils
x86-64, init: Fix a possible wraparound bug in switchover in head_64.S
x86, range: fix missing merge during add range
x86, efi: initial the local variable of DataSize to zero
efivar: fix oops in efivar_update_sysfs_entries() caused by memory reuse
efivarfs: Never return ENOENT from firmware again
Pekka Riikonen [Mon, 13 May 2013 12:32:07 +0000 (14:32 +0200)]
x86: Allow FPU to be used at interrupt time even with eagerfpu
With the addition of eagerfpu the irq_fpu_usable() now returns false
negatives especially in the case of ksoftirqd and interrupted idle task,
two common cases for FPU use for example in networking/crypto. With
eagerfpu=off FPU use is possible in those contexts. This is because of
the eagerfpu check in interrupted_kernel_fpu_idle():
...
* For now, with eagerfpu we will return interrupted kernel FPU
* state as not-idle. TBD: Ideally we can change the return value
* to something like __thread_has_fpu(current). But we need to
* be careful of doing __thread_clear_has_fpu() before saving
* the FPU etc for supporting nested uses etc. For now, take
* the simple route!
...
if (use_eager_fpu())
return 0;
As eagerfpu is automatically "on" on those CPUs that also have the
features like AES-NI this patch changes the eagerfpu check to return 1 in
case the kernel_fpu_begin() has not been said yet. Once it has been the
__thread_has_fpu() will start returning 0.
Notice that with eagerfpu the __thread_has_fpu is always true initially.
FPU use is thus always possible no matter what task is under us, unless
the state has already been saved with kernel_fpu_begin().
[ hpa: this is a performance regression, not a correctness regression,
but since it can be quite serious on CPUs which need encryption at
interrupt time I am marking this for urgent/stable. ]
Jan Beulich [Wed, 29 May 2013 12:43:54 +0000 (13:43 +0100)]
x86, crc32-pclmul: Fix build with older binutils
binutils prior to 2.18 (e.g. the ones found on SLE10) don't support
assembling PEXTRD, so a macro based approach like the one for PCLMULQDQ
in the same file should be used.
This requires making the helper macros capable of recognizing 32-bit
general purpose register operands.
[ hpa: tagging for stable as it is a low risk build fix ]
Signed-off-by: Jan Beulich <jbeulich@suse.com> Link: http://lkml.kernel.org/r/51A6142A02000078000D99D8@nat28.tlf.novell.com Cc: Alexander Boyko <alexander_boyko@xyratex.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Huang Ying <ying.huang@intel.com> Cc: <stable@vger.kernel.org> v3.9 Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Dave Chinner [Tue, 21 May 2013 08:02:08 +0000 (18:02 +1000)]
xfs: rework remote attr CRCs
Note: this changes the on-disk remote attribute format. I assert
that this is OK to do as CRCs are marked experimental and the first
kernel it is included in has not yet reached release yet. Further,
the userspace utilities are still evolving and so anyone using this
stuff right now is a developer or tester using volatile filesystems
for testing this feature. Hence changing the format right now to
save longer term pain is the right thing to do.
The fundamental change is to move from a header per extent in the
attribute to a header per filesytem block in the attribute. This
means there are more header blocks and the parsing of the attribute
data is slightly more complex, but it has the advantage that we
always know the size of the attribute on disk based on the length of
the data it contains.
This is where the header-per-extent method has problems. We don't
know the size of the attribute on disk without first knowing how
many extents are used to hold it. And we can't tell from a
mapping lookup, either, because remote attributes can be allocated
contiguously with other attribute blocks and so there is no obvious
way of determining the actual size of the atribute on disk short of
walking and mapping buffers.
The problem with this approach is that if we map a buffer
incorrectly (e.g. we make the last buffer for the attribute data too
long), we then get buffer cache lookup failure when we map it
correctly. i.e. we get a size mismatch on lookup. This is not
necessarily fatal, but it's a cache coherency problem that can lead
to returning the wrong data to userspace or writing the wrong data
to disk. And debug kernels will assert fail if this occurs.
I found lots of niggly little problems trying to fix this issue on a
4k block size filesystem, finally getting it to pass with lots of
fixes. The thing is, 1024 byte filesystems still failed, and it was
getting really complex handling all the corner cases that were
showing up. And there were clearly more that I hadn't found yet.
It is complex, fragile code, and if we don't fix it now, it will be
complex, fragile code forever more.
Hence the simple fix is to add a header to each filesystem block.
This gives us the same relationship between the attribute data
length and the number of blocks on disk as we have without CRCs -
it's a linear mapping and doesn't require us to guess anything. It
is simple to implement, too - the remote block count calculated at
lookup time can be used by the remote attribute set/get/remove code
without modification for both CRC and non-CRC filesystems. The world
becomes sane again.
Because the copy-in and copy-out now need to iterate over each
filesystem block, I moved them into helper functions so we separate
the block mapping and buffer manupulations from the attribute data
and CRC header manipulations. The code becomes much clearer as a
result, and it is a lot easier to understand and debug. It also
appears to be much more robust - once it worked on 4k block size
filesystems, it has worked without failure on 1k block size
filesystems, too.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit ad1858d77771172e08016890f0eb2faedec3ecee)
Dave Chinner [Tue, 21 May 2013 08:02:06 +0000 (18:02 +1000)]
xfs: fully initialise temp leaf in xfs_attr3_leaf_compact
xfs_attr3_leaf_compact() uses a temporary buffer for compacting the
the entries in a leaf. It copies the the original buffer into the
temporary buffer, then zeros the original buffer completely. It then
copies the entries back into the original buffer. However, the
original buffer has not been correctly initialised, and so the
movement of the entries goes horribly wrong.
Make sure the zeroed destination buffer is fully initialised, and
once we've set up the destination incore header appropriately, write
is back to the buffer before starting to move entries around.
While debugging this, the _d/_s prefixes weren't sufficient to
remind me what buffer was what, so rename then all _src/_dst.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit d4c712bcf26a25c2b67c90e44e0b74c7993b5334)
Dave Chinner [Tue, 21 May 2013 08:02:05 +0000 (18:02 +1000)]
xfs: fully initialise temp leaf in xfs_attr3_leaf_unbalance
xfs_attr3_leaf_unbalance() uses a temporary buffer for recombining
the entries in two leaves when the destination leaf requires
compaction. The temporary buffer ends up being copied back over the
original destination buffer, so the header in the temporary buffer
needs to contain all the information that is in the destination
buffer.
To make sure the temporary buffer is fully initialised, once we've
set up the temporary incore header appropriately, write is back to
the temporary buffer before starting to move entries around.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 8517de2a81da830f5d90da66b4799f4040c76dc9)
Dave Chinner [Tue, 21 May 2013 08:02:04 +0000 (18:02 +1000)]
xfs: correctly map remote attr buffers during removal
If we don't map the buffers correctly (same as for get/set
operations) then the incore buffer lookup will fail. If a block
number matches but a length is wrong, then debug kernels will ASSERT
fail in _xfs_buf_find() due to the length mismatch. Ensure that we
map the buffers correctly by basing the length of the buffer on the
attribute data length rather than the remote block count.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 6863ef8449f1908c19f43db572e4474f24a1e9da)
Dave Chinner [Tue, 21 May 2013 08:02:03 +0000 (18:02 +1000)]
xfs: remote attribute tail zeroing does too much
When an attribute data does not fill then entire remote block, we
zero the remaining part of the buffer. This, however, needs to take
into account that the buffer has a header, and so the offset where
zeroing starts and the length of zeroing need to take this into
account. Otherwise we end up with zeros over the end of the
attribute value when CRCs are enabled.
While there, make sure we only ask to map an extent that covers the
remaining range of the attribute, rather than asking every time for
the full length of remote data. If the remote attribute blocks are
contiguous with other parts of the attribute tree, it will map those
blocks as well and we can potentially zero them incorrectly. We can
also get buffer size mistmatches when trying to read or remove the
remote attribute, and this can lead to not finding the correct
buffer when looking it up in cache.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 4af3644c9a53eb2f1ecf69cc53576561b64be4c6)
Dave Chinner [Tue, 21 May 2013 08:02:02 +0000 (18:02 +1000)]
xfs: remote attribute read too short
Reading a maximally size remote attribute fails when CRCs are
enabled with this verification error:
XFS (vdb): remote attribute header does not match required off/len/owner)
There are two reasons for this, the first being that the
length of the buffer being read is determined from the
args->rmtblkcnt which doesn't take into account CRC headers. Hence
the mapped length ends up being too short and so we need to
calculate it directly from the value length.
The second is that the byte count of valid data within a buffer is
capped by the length of the data and so doesn't take into account
that the buffer might be longer due to headers. Hence we need to
calculate the data space in the buffer first before calculating the
actual byte count of data.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 913e96bc292e1bb248854686c79d6545ef3ee720)
Dave Chinner [Tue, 21 May 2013 08:02:01 +0000 (18:02 +1000)]
xfs: remote attribute allocation may be contiguous
When CRCs are enabled, there may be multiple allocations made if the
headers cause a length overflow. This, however, does not mean that
the number of headers required increases, as the second and
subsequent extents may be contiguous with the previous extent. Hence
when we map the extents to write the attribute data, we may end up
with less extents than allocations made. Hence the assertion that we
consume the number of headers we calculated in the allocation loop
is incorrect and needs to be removed.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 90253cf142469a40f89f989904abf0a1e500e1a6)
Dave Chinner [Tue, 28 May 2013 08:37:17 +0000 (18:37 +1000)]
xfs: fix dir3 freespace block corruption
When the directory freespace index grows to a second block (2017
4k data blocks in the directory), the initialisation of the second
new block header goes wrong. The write verifier fires a corruption
error indicating that the block number in the header is zero. This
was being tripped by xfs/110.
The problem is that the initialisation of the new block is done just
fine in xfs_dir3_free_get_buf(), but the caller then users a dirv2
structure to zero on-disk header fields that xfs_dir3_free_get_buf()
has already zeroed. These lined up with the block number in the dir
v3 header format.
While looking at this, I noticed that the struct xfs_dir3_free_hdr()
had 4 bytes of padding in it that wasn't defined as padding or being
zeroed by the initialisation. Add a pad field declaration and fully
zero the on disk and in-core headers in xfs_dir3_free_get_buf() so
that this is never an issue in the future. Note that this doesn't
change the on-disk layout, just makes the 32 bits of padding in the
layout explicit.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 5ae6e6a401957698f2bd8c9f4a86d86d02199fea)
Dave Chinner [Mon, 27 May 2013 06:38:24 +0000 (16:38 +1000)]
xfs: disable swap extents ioctl on CRC enabled filesystems
Currently, swapping extents from one inode to another is a simple
act of switching data and attribute forks from one inode to another.
This, unfortunately in no longer so simple with CRC enabled
filesystems as there is owner information embedded into the BMBT
blocks that are swapped between inodes. Hence swapping the forks
between inodes results in the inodes having mapping blocks that
point to the wrong owner and hence are considered corrupt.
To fix this we need an extent tree block or record based swap
algorithm so that the BMBT block owner information can be updated
atomically in the swap transaction. This is a significant piece of
new work, so for the moment simply don't allow swap extent
operations to succeed on CRC enabled filesystems.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 02f75405a75eadfb072609f6bf839e027de6a29a)
Dave Chinner [Mon, 27 May 2013 06:38:26 +0000 (16:38 +1000)]
xfs: add fsgeom flag for v5 superblock support.
Currently userspace has no way of determining that a filesystem is
CRC enabled. Add a flag to the XFS_IOC_FSGEOMETRY ioctl output to
indicate that the filesystem has v5 superblock support enabled.
This will allow xfs_info to correctly report the state of the
filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 74137fff067961c9aca1e14d073805c3de8549bd)
projects / karo-tx-linux.git / log