md-cluster: Do not printk() every received message
The receive daemon prints kernel messages for every network message
received. This would fill the kernel message log with unnecessary messages.
Remove the pr_info() messages.
md-cluster: Fix adding of new disk with new reload code
Adding the disk worked incorrectly with the new reload code. Fix it:
- No operation should be performed on rdev marked as Candidate
- After a metadata update operation, kick disk if role is 0xfffe
else clear Candidate bit and continue with the regular change check.
- Saving the mode of the lock resource to check if token lock is already
locked, because it can be called twice while adding a disk. However,
unlock_comm() must be called only once.
- add_new_disk() is called by the node initiating the --add operation.
If it needs to be canceled, call add_new_disk_cancel(). The operation
is completed by md_update_sb() which will write and unlock the
communication.
md-cluster: Perform resync/recovery under a DLM lock
Resync or recovery must be performed by only one node at a time.
A DLM lock resource, resync_lockres provides the mutual exclusion
so that only one node performs the recovery/resync at a time.
If a node is unable to get the resync_lockres, because recovery is
being performed by another node, it set MD_RECOVER_NEEDED so as
to schedule recovery in the future.
Remove the debug message in resync_info_update()
used during development.
In a clustered environment, a change such as marking a device faulty,
can be recorded by any of the nodes. This is communicated to all the
nodes and re-recording such a change is unnecessary, and quite often
pretty disruptive.
With this patch, just before the update, we detect for the changes
and if the changes are already in superblock, we abort the update
after clearing all the flags
md-cluster: Improve md_reload_sb to be less error prone
md_reload_sb is too simplistic and it explicitly needs to determine
the changes made by the writing node. However, there are multiple areas
where a simple reload could fail.
Instead, read the superblock of one of the "good" rdevs and update
the necessary information:
- read the superblock into a newly allocated page, by temporarily
swapping out rdev->sb_page and calling ->load_super.
- if that fails return
- if it succeeds, call check_sb_changes
1. iterates over list of active devices and checks the matching
dev_roles[] value.
If that is 'faulty', the device must be marked as faulty
- call md_error to mark the device as faulty. Make sure
not to set CHANGE_DEVS and wakeup mddev->thread or else
it would initiate a resync process, which is the responsibility
of the "primary" node.
- clear the Blocked bit
- Call remove_and_add_spares() to hot remove the device.
If the device is 'spare':
- call remove_and_add_spares() to get the number of spares
added in this operation.
- Reduce mddev->degraded to mark the array as not degraded.
2. reset recovery_cp
- read the rest of the rdevs to update recovery_offset. If recovery_offset
is equal to MaxSector, call spare_active() to set it In_sync
This required that recovery_offset be initialized to MaxSector, as
opposed to zero so as to communicate the end of sync for a rdev.
md-cluster: send BITMAP_NEEDS_SYNC when node is leaving cluster
Previously, BITMAP_NEEDS_SYNC message is sent when the resyc
aborts, but it could abort for different reasons, and not all
of reasons require another node to take over the resync ownship.
It is better make BITMAP_NEEDS_SYNC message only be sent when
the node is leaving cluster with dirty bitmap. And we also need
to ensure dlm connection is ok.
Suspending the entire device for resync could take too long. Resync
in small chunks.
cluster's resync window (32M) is maintained in r1conf as
cluster_sync_low and cluster_sync_high and processed in
raid1's sync_request(). If the current resync is outside the cluster
resync window:
1. Set the cluster_sync_low to curr_resync_completed.
2. Check if the sync will fit in the new window, if not issue a
wait_barrier() and set cluster_sync_low to sector_nr.
3. Set cluster_sync_high to cluster_sync_low + resync_window.
4. Send a message to all nodes so they may add it in their suspension
list.
bitmap_cond_end_sync is modified to allow to force a sync inorder
to get the curr_resync_completed uptodate with the sector passed.
md-cluster: complete all write requests before adding suspend_info
process_suspend_info - which handles the RESYNCING request - must not
reply until all writes which were initiated before the request arrived,
have completed.
As a by-product, all process_* functions now take mddev as their
first arguement making it uniform.
NeilBrown [Thu, 1 Oct 2015 06:03:38 +0000 (16:03 +1000)]
md/bitmap: don't pass -1 to bitmap_storage_alloc.
Passing -1 to bitmap_storage_alloc() causes page->index to be set to
-1, which is quite problematic.
So only pass ->cluster_slot if mddev_is_clustered().
Fixes: b97e92574c0b ("Use separate bitmaps for each nodes in the cluster") Cc: stable@vger.kernel.org (v4.1+) Signed-off-by: NeilBrown <neilb@suse.com>
close_sync() needs to set conf->next_resync to a large, but safe value
below MaxSector and use it to determine whether or not to set
start_next_window in wait_barrier()
Shaohua Li [Fri, 18 Sep 2015 17:20:12 +0000 (10:20 -0700)]
md: clear CHANGE_PENDING in readonly array
If faulty disks of an array are more than allowed degraded number, the
array enters error handling. It will be marked as read-only with
MD_CHANGE_PENDING/RECOVERY_NEEDED set. But currently recovery doesn't
clear CHANGE_PENDING bit for read-only array. If MD_CHANGE_PENDING is
set for a raid5 array, all returned IO will be hold on a list till the
bit is clear. But recovery nevery clears this bit, the IO is always in
pending state and nevery finish. This has bad effects like upper layer
can't get an IO error and the array can't be stopped.
Fixes: c3cce6cda162 ("md/raid5: ensure device failure recorded before write request returns.") Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
md/raid0: apply base queue limits *before* disk_stack_limits
Calling e.g. blk_queue_max_hw_sectors() after calls to
disk_stack_limits() discards the settings determined by
disk_stack_limits().
So we need to make those calls first.
Fixes: 199dc6ed5179 ("md/raid0: update queue parameter in a safer location.") Cc: stable@vger.kernel.org (v2.6.35+ - please apply with 199dc6ed5179). Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com>
md/raid5: don't index beyond end of array in need_this_block().
When need_this_block probably shouldn't be called when there
are more than 2 failed devices, we really don't want it to try
indexing beyond the end of the failed_num[] of fdev[] arrays.
So limit the loops to at most 2 iterations.
Reported-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.de>
Shaohua Li [Fri, 18 Sep 2015 17:20:13 +0000 (10:20 -0700)]
raid5: update analysis state for failed stripe
handle_failed_stripe() makes the stripe fail, eg, all IO will return
with a failure, but it doesn't update stripe_head_state. Later
handle_stripe() has special handling for raid6 for handle_stripe_fill().
That check before handle_stripe_fill() doesn't skip the failed stripe
and we get a kernel crash in need_this_block. This patch clear the
analysis state to make sure no functions wrongly called after
handle_failed_stripe()
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
md: wait for pending superblock updates before switching to read-only
If a superblock update is pending, wait for it to complete before
letting md_set_readonly() switch to readonly.
Otherwise we might lose important information about a device having
failed.
For external arrays, waiting for superblock updates can wait on
user-space, so in that case, just return an error.
Reported-and-tested-by: Shaohua Li <shli@fb.com> Signed-off-by: NeilBrown <neilb@suse.com>
Merge branch 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"The threadgroup locking changes which went in during 4.2 devel cycle
added write locking of a percpu_rwsem in cgroup task migration path;
unfortunately, that involved expedited rcu syncing which turned out to
be too slow and heavy for certain workloads. The patchset which is
dependent on this one didn't get committed during that devel cycle, so
these two patches can be reverted safely.
Oleg reworked percpu_rwsem for 4.4 so that the writer path is a lot
lighter. The reported issue goes away with Oleg's reworked
percpu_rwsem and I'll reapply these patches on the for-4.4 branch so
that they can land together with Oleg's changes"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Revert "sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem"
Revert "cgroup: simplify threadgroup locking"
Merge tag 'renesas-sh-drivers-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH drivers updates from Simon Horman:
"I am sending this change after v4.3-rc1 has been released as it
depends on SoC changes which are present in that rc release.
Summary:
- disable PM runtime for multi-platform ARM with genpd
- disable legacy default PM Domain on emev2"
* tag 'renesas-sh-drivers-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Disable PM runtime for multi-platform ARM with genpd
drivers: sh: Disable legacy default PM Domain on emev2
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of system call updates. The two new system calls userfaultfd
and membarrier have been added, as well as the 17 direct calls for the
multiplexed socket system calls.
In addition the system call compat wrappers have been flagged as
notrace functions and a few wrappers could be removed.
And bug fixes for the vector register handling, cpu_mf, suspend/resume,
compat signals, SMT cputime accounting and the zfcp dumper"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up separate socketcalls system calls
s390/compat: remove superfluous compat wrappers
s390/compat: do not trace compat wrapper functions
s390/s390x: allocate sys_membarrier system call number
s390/configs//zfcpdump_defconfig: Remove CONFIG_MEMSTICK
s390: wire up userfaultfd system call
s390/vtime: correct scaled cputime for SMT
s390/cpum_cf: Corrected return code for unauthorized counter sets
s390/compat: correct uc_sigmask of the compat signal frame
s390: fix floating point register corruption
s390/hibernate: fix save and restore of vector registers
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three fixes and a resulting cleanup for -rc2:
- Andre Przywara reported that he was seeing a warning with the new
cast inside DMA_ERROR_CODE's definition, and fixed the incorrect
use.
- Doug Anderson noticed that kgdb causes a "scheduling while atomic"
bug.
- OMAP5 folk noticed that their Thumb-2 compiled X servers crashed
when enabling support to cover ARMv6 CPUs due to a kernel bug
leaking some conditional context into the signal handler"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8425/1: kgdb: Don't try to stop the machine when setting breakpoints
ARM: 8437/1: dma-mapping: fix build warning with new DMA_ERROR_CODE definition
ARM: get rid of needless #if in signal handling code
ARM: fix Thumb2 signal handling when ARMv6 is enabled
Merge tag 'linux-kselftest-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update contains 7 fixes for problems ranging from build failurs
to incorrect error reporting"
* tag 'linux-kselftest-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: exec: revert to default emit rule
selftests: change install command to rsync
selftests: mqueue: simplify the Makefile
selftests: mqueue: allow extra cflags
selftests: rename jump label to static_keys
selftests/seccomp: add support for s390
seltests/zram: fix syntax error
Merge tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Included are: a somewhat late devfreq update which however is mostly
fixes and cleanups with one new thing only (the PPMUv2 support on
Exynos5433), an ACPI cpufreq driver fixup and two ACPI core cleanups
related to preprocessor directives.
Specifics:
- Fix a memory allocation size in the devfreq core (Xiaolong Ye).
- Fix a mistake in the exynos-ppmu DT binding (Javier Martinez
Canillas).
- Add support for PPMUv2 ((Platform Performance Monitoring Unit
version 2.0) on the Exynos5433 SoCs (Chanwoo Choi).
- Fix a type casting bug in the Exynos PPMU code (MyungJoo Ham).
- Assorted devfreq code cleanups and optimizations (Javi Merino,
MyungJoo Ham, Viresh Kumar).
- Fix up the ACPI cpufreq driver to use a more lightweight way to get
to its private data in the ->get() callback (Rafael J Wysocki).
- Fix a CONFIG_ prefix bug in one of the ACPI drivers and make the
ACPI subsystem use IS_ENABLED() instead of #ifdefs in function
bodies (Sudeep Holla)"
* tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
ACPI: Eliminate CONFIG_.*{, _MODULE} #ifdef in favor of IS_ENABLED()
ACPI: int340x_thermal: add missing CONFIG_ prefix
PM / devfreq: Fix incorrect type issue.
PM / devfreq: tegra: Update governor to use devfreq_update_stats()
PM / devfreq: comments for get_dev_status usage updated
PM / devfreq: drop comment about thermal setting max_freq
PM / devfreq: cache the last call to get_dev_status()
PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few driver fixes for tegra, rockchip, and st SoCs and a two-liner in
the framework to avoid oops when get_parent ops return out of range
values on tegra platforms"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x
clk: check for invalid parent index of orphans in __clk_init()
clk: tegra: dfll: Properly protect OPP list
clk: rockchip: add critical clock for rk3368
Merge tag 'led-fixes-for-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
- fix module autoload for six OF platform drivers (aat1290, bcm6328,
bcm6358, ktd2692, max77693, ns2)
- aat1290: add missing static modifier
- ipaq-micro: add missing LEDS_CLASS dependency
- lp55xx: correct Kconfig dependecy for f/w user helper
* tag 'led-fixes-for-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds:lp55xx: Correct Kconfig dependency for f/w user helper
leds: leds-ipaq-micro: Add LEDS_CLASS dependency
leds: aat1290: add 'static' modifier to init_mm_current_scale
leds: leds-ns2: Fix module autoload for OF platform driver
leds: max77693: Fix module autoload for OF platform driver
leds: ktd2692: Fix module autoload for OF platform driver
leds: bcm6358: Fix module autoload for OF platform driver
leds: bcm6328: Fix module autoload for OF platform driver
leds: aat1290: Fix module autoload for OF platform driver
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"The new hfi1 driver in staging/rdma has had a number of fixup patches
since being added to the tree. This is the first batch of those fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hfi: Properly set permissions for user device files
IB/hfi1: mask vs shift confusion
IB/hfi1: clean up some defines
IB/hfi1: info leak in get_ctxt_info()
IB/hfi1: fix a locking bug
IB/hfi1: checking for NULL instead of IS_ERR
IB/hfi1: fix sdma_descq_cnt parameter parsing
IB/hfi1: fix copy_to/from_user() error handling
IB/hfi1: fix pstateinfo from returning improperly byteswapped value
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- a boot regression (since v4.2) fix for some ARM configurations from
Tyler
- regression (since v4.1) fixes for mkfs.xfs on a DAX enabled device
from Jeff. These are tagged for -stable.
- a pair of locking fixes from Axel that are hidden from lockdep since
they involve device_lock(). The "btt" one is tagged for -stable, the
other only applies to the new "pfn" mechanism in v4.3.
- a fix for the pmem ->rw_page() path to use wmb_pmem() from Ross.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
mm: fix type cast in __pfn_to_phys()
pmem: add proper fencing to pmem_rw_page()
libnvdimm: pfn_devs: Fix locking in namespace_store
libnvdimm: btt_devs: Fix locking in namespace_store
blockdev: don't set S_DAX for misaligned partitions
dax: fix O_DIRECT I/O to the last block of a blockdev
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is a bit bigger than it should be, but I could (did) not want to
send it off last week due to both wanting extra testing, and expecting
a fix for the bounce regression as well. In any case, this contains:
- Fix for the blk-merge.c compilation warning on gcc 5.x from me.
- A set of back/front SG gap merge fixes, from me and from Sagi.
This ensures that we honor SG gapping for integrity payloads as
well.
- Two small fixes for null_blk from Matias, fixing a leak and a
capacity propagation issue.
- A blkcg fix from Tejun, fixing a NULL dereference.
- A fast clone optimization from Ming, fixing a performance
regression since the arbitrarily sized bio's were introduced.
- Also from Ming, a regression fix for bouncing IOs"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bounce_end_io
block: blk-merge: fast-clone bio when splitting rw bios
block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg
block: Copy a user iovec if it includes gaps
block: Refuse adding appending a gapped integrity page to a bio
block: Refuse request/bio merges with gaps in the integrity payload
block: Check for gaps on front and back merges
null_blk: fix wrong capacity when bs is not 512 bytes
null_blk: fix memory leak on cleanup
block: fix bogus compiler warnings in blk-merge.c
Chris Mason [Fri, 18 Sep 2015 17:35:08 +0000 (13:35 -0400)]
fs-writeback: unplug before cond_resched in writeback_sb_inodes
Commit 505a666ee3fc ("writeback: plug writeback in wb_writeback() and
writeback_inodes_wb()") has us holding a plug during writeback_sb_inodes,
which increases the merge rate when relatively contiguous small files
are written by the filesystem. It helps both on flash and spindles.
For an fs_mark workload creating 4K files in parallel across 8 drives,
this commit improves performance ~9% more by unplugging before calling
cond_resched(). cond_resched() doesn't trigger an implicit unplug, so
explicitly getting the IO down to the device before scheduling reduces
latencies for anyone waiting on clean pages.
It also cuts down on how often we use kblockd to unplug, which means
less work bouncing from one workqueue to another.
Many more details about how we got here:
https://lkml.org/lkml/2015/9/11/570
Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various definitions of __pfn_to_phys() have been consolidated to
use a generic macro in include/asm-generic/memory_model.h. This hit
mainline in the form of 012dcef3f058 "mm: move __phys_to_pfn and
__pfn_to_phys to asm/generic/memory_model.h". When the generic macro
was implemented the type cast to phys_addr_t was dropped which caused
boot regressions on ARM platforms with more than 4GB of memory and
LPAE enabled.
It was suggested to use PFN_PHYS() defined in include/linux/pfn.h
as provides the correct logic and avoids further duplication.
Reported-by: kernelci.org bot <bot@kernelci.org> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tyler Baker <tyler.baker@linaro.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* pm-cpufreq:
cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
* pm-devfreq:
PM / devfreq: Fix incorrect type issue.
PM / devfreq: tegra: Update governor to use devfreq_update_stats()
PM / devfreq: comments for get_dev_status usage updated
PM / devfreq: drop comment about thermal setting max_freq
PM / devfreq: cache the last call to get_dev_status()
PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes and cleanups from Michael Tsirkin:
"This fixes the virtio-test tool, and improves the error handling for
virtio-ccw"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: handle failures of READ_VQ_CONF ccw
tools/virtio: propagate V=X to kernel build
vhost: move features to core
tools/virtio: fix build after 4.2 changes
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Mostly stable material, a lot of ARM fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
sched: access local runqueue directly in single_task_running
arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
arm64: KVM: Remove all traces of the ThumbEE registers
arm: KVM: Disable virtual timer even if the guest is not using it
arm64: KVM: Disable virtual timer even if the guest is not using it
arm/arm64: KVM: vgic: Check for !irqchip_in_kernel() when mapping resources
KVM: s390: Replace incorrect atomic_or with atomic_andnot
arm: KVM: Fix incorrect device to IPA mapping
arm64: KVM: Fix user access for debug registers
KVM: vmx: fix VPID is 0000H in non-root operation
KVM: add halt_attempted_poll to VCPU stats
kvm: fix zero length mmio searching
kvm: fix double free for fast mmio eventfd
kvm: factor out core eventfd assign/deassign logic
kvm: don't try to register to KVM_FAST_MMIO_BUS for non mmio eventfd
KVM: make the declaration of functions within 80 characters
KVM: arm64: add workaround for Cortex-A57 erratum #852523
KVM: fix polling for guest halt continued even if disable it
arm/arm64: KVM: Fix PSCI affinity info return value for non valid cores
arm64: KVM: set {v,}TCR_EL2 RES1 bits
...
Ira Weiny [Thu, 17 Sep 2015 17:47:49 +0000 (13:47 -0400)]
IB/hfi: Properly set permissions for user device files
Some of the device files are required to be user accessible for PSM while
most should remain accessible only by root.
Add a parameter to hfi1_cdev_init which controls if the user should have access
to this device which places it in a different class with the appropriate
devnode callback.
In addition set the devnode call back for the existing class to be a bit more
explicit for those permissions.
Finally remove the unnecessary null check before class_destroy
Tested-by: Donald Dutile <ddutile@redhat.com> Signed-off-by: Haralanov, Mitko (mitko.haralanov@intel.com) Signed-off-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Dan Carpenter [Wed, 16 Sep 2015 16:02:54 +0000 (19:02 +0300)]
IB/hfi1: clean up some defines
I added spaces around operators so it matches kernel style because
normally "-1ULL" is a number and " - 1" is a subtract operation. Also
removed some superflous "ULL" types so "1ULL" becomes "1".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
Merge tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from
Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change
from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper
from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from
Christophe
* tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc32: memset: only use dcbz once cache is enabled
powerpc32: memcpy: only use dcbz once cache is enabled
powerpc/mm: Recompute hash value after a failed update
powerpc/boot: Specify ABI v2 when building an LE boot wrapper
cxl: Fix build failure due to -Wunused-variable behaviour change
cxl: Fix unbalanced pci_dev_get in cxl_probe
powerpc/MSI: Fix race condition in tearing down MSI interrupts
powerpc: Wire up sys_userfaultfd()
powerpc/pseries: Release DRC when configure_connector fails
cxl: abort cxl_pci_enable_device_hook() if PCI channel is offline
powerpc/powernv/pci-ioda: fix kdump with non-power-of-2 crashkernel=
powerpc/powernv/pci-ioda: fix 32-bit TCE table init in kdump kernel
sched: access local runqueue directly in single_task_running
Commit 2ee507c47293 ("sched: Add function single_task_running to let a task
check if it is the only task running on a cpu") referenced the current
runqueue with the smp_processor_id. When CONFIG_DEBUG_PREEMPT is enabled,
that is only allowed if preemption is disabled or the currrent task is
bound to the local cpu (e.g. kernel worker).
With commit f78195129963 ("kvm: add halt_poll_ns module parameter") KVM
calls single_task_running. If CONFIG_DEBUG_PREEMPT is enabled that
generates a lot of kernel messages.
To avoid adding preemption in that cases, as it would limit the usefulness,
we change single_task_running to access directly the cpu local runqueue.
Cc: Tim Chen <tim.c.chen@linux.intel.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@vger.kernel.org> Fixes: 2ee507c472939db4b146d545352b8a7c79ef47f8 Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A couple of compat wrapper functions are simply trampolines to the real
system call. This happened because the compat wrapper defines will only
sign and zero extend system call parameters which are of different size
on s390/s390x (longs and pointers).
All other parameters will be correctly sign and zero extended by the
normal system call wrappers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/compat: do not trace compat wrapper functions
Add notrace to the compat wrapper define to disable tracing of compat
wrapper functions. These are supposed to be very small and more or less
just a trampoline to the real system call.
Also fix indentation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge tag 'platform-drivers-x86-v4.3-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix an issue introduced by the previous major toshiba rework. Add a
quirk. Workaround a few platform specific firmware items. One
cleanup to wmi I inadvertently dropped from a previous pull request.
Details:
hp-wmi:
- limit hotkey enable
toshiba_acpi:
- Fix hotkeys registration on some toshiba models
- Fix USB Sleep and Music always disabled
wmi:
- Remove private %pUL implementation
asus-nb-wmi:
- Add wapf=4 quirk for X456UA/X456UF"
* tag 'platform-drivers-x86-v4.3-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
hp-wmi: limit hotkey enable
toshiba_acpi: Fix hotkeys registration on some toshiba models
toshiba_acpi: Fix USB Sleep and Music always disabled
wmi: Remove private %pUL implementation
asus-nb-wmi: Add wapf=4 quirk for X456UA/X456UF
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
revert "mm: make sure all file VMAs have ->vm_ops set"
MAINTAINERS: update LTP mailing list
userfaultfd: add missing mmput() in error path
lib/string_helpers.c: fix infinite loop in string_get_size()
alpha: lib: export __delay
alpha: io: define ioremap_uc
kasan: fix last shadow judgement in memory_is_poisoned_16()
zram: fix possible use after free in zcomp_create()
Andrew Morton [Thu, 17 Sep 2015 23:02:00 +0000 (16:02 -0700)]
revert "mm: make sure all file VMAs have ->vm_ops set"
Revert commit 6dc296e7df4c "mm: make sure all file VMAs have ->vm_ops
set".
Will Deacon reports that it "causes some mmap regressions in LTP, which
appears to use a MAP_PRIVATE mmap of /dev/zero as a way to get anonymous
pages in some of its tests (specifically mmap10 [1])".
William Shuman reports Oracle crashes.
So revert the patch while we work out what to do.
Reported-by: William Shuman <wshuman3@gmail.com> Reported-by: Will Deacon <will.deacon@arm.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/string_helpers.c: fix infinite loop in string_get_size()
Some string_get_size() calls (e.g.:
string_get_size(1, 512, STRING_UNITS_10, ..., ...)
string_get_size(15, 64, STRING_UNITS_10, ..., ...)
) result in an infinite loop. The problem is that if size is equal to
divisor[units]/blk_size and is smaller than divisor[units] we'll end
up with size == 0 when we start doing sf_cap calculations:
For string_get_size(1, 512, STRING_UNITS_10, ..., ...) case:
...
remainder = do_div(size, divisor[units]); -> size is 0, remainder is 1
remainder *= blk_size; -> remainder is 512
...
size *= blk_size; -> size is still 0
size += remainder / divisor[units]; -> size is still 0
The caller causing the issue is sd_read_capacity(), the problem was
noticed on Hyper-V, such weird size was reported by host when scanning
collides with device removal. This is probably a separate issue worth
fixing, this patch is intended to prevent the library routine from
infinite looping.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: James Bottomley <JBottomley@Odin.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__delay was not exported as a result while building with allmodconfig we
were getting build error of undefined symbol. __delay is being used by:
drivers/net/phy/mdio-octeon.c
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ioremap_uc was not defined and as a result while building with
allmodconfig were getting build error of: implicit declaration of
function 'ioremap_uc'.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kasan: fix last shadow judgement in memory_is_poisoned_16()
The shadow which correspond 16 bytes memory may span 2 or 3 bytes. If
the memory is aligned on 8, then the shadow takes only 2 bytes. So we
check "shadow_first_bytes" is enough, and need not to call
"memory_is_poisoned_1(addr + 15);". But the code "if
(likely(!last_byte))" is wrong judgement.
e.g. addr=0, so last_byte = 15 & KASAN_SHADOW_MASK = 7, then the code
will continue to call "memory_is_poisoned_1(addr + 15);"
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andrey Konovalov <adech.fo@gmail.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michal Marek <mmarek@suse.cz> Cc: <zhongjiang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Luis Henriques [Thu, 17 Sep 2015 23:01:40 +0000 (16:01 -0700)]
zram: fix possible use after free in zcomp_create()
zcomp_create() verifies the success of zcomp_strm_{multi,single}_create()
through comp->stream, which can potentially be pointing to memory that
was freed if these functions returned an error.
While at it, replace a 'ERR_PTR(-ENOMEM)' by a more generic
'ERR_PTR(error)' as in the future zcomp_strm_{multi,siggle}_create()
could return other error codes. Function documentation updated
accordingly.
Fixes: beca3ec71fe5 ("zram: add multi stream functionality") Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not write initialize magic on systems that do not have
feature query 0xb. Fixes Bug #82451.
Redefine FEATURE_QUERY to align with 0xb and FEATURE2 with 0xd
for code clearity.
Add a new test function, hp_wmi_bios_2008_later() & simplify
hp_wmi_bios_2009_later(), which fixes a bug in cases where
an improper value is returned. Probably also fixes Bug #69131.
Add missing __init tag.
Signed-off-by: Kyle Evans <kvans32@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"These are both fixes to the new and improved keepalive2 behavior"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: advertise support for keepalive2
libceph: don't access invalid memory in keepalive2 path
Merge tag 'for-v4.3-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"twl4030-charger fixes"
* tag 'for-v4.3-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
twl4030_charger: fix another compile error
Revert "twl4030_charger: correctly handle -EPROBE_DEFER from devm_usb_get_phy_by_node"
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"This addresses some problems with filesystem writeback due to the
recently merged hardware DBM patches, which caused us to treat some
read-only pages as dirty.
There are also some other, less significant fixes that are described
in the summary below:
A mixture of fixes for regressions introduced during the merge window,
some longer standing problems that we spotted and a couple of hardware
errata. The main changes are:
- Fix fallout from the h/w DBM patches, causing filesystem writeback
issues on both v8 and v8.1 CPUs
- Workaround for Cortex-A53 erratum #843419 in the module loader
- Fix for long-standing issue with compat big-endian signal handlers
using the saved floating point state"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: errata: add module build workaround for erratum #843419
arm64: compat: fix vfp save/restore across signal handlers in big-endian
arm64: cpu hotplug: ensure we mask out CPU_TASKS_FROZEN in notifiers
arm64: head.S: initialise mdcr_el2 in el2_setup
arm64: enable generic idle loop
arm64: pgtable: use a single bit for PTE_WRITE regardless of DBM
arm64: Fix pte_modify() to preserve the hardware dirty information
arm64: Fix the pte_hw_dirty() check when AF/DBM is enabled
arm64: dma-mapping: check whether cma area is initialized or not
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- misc fixes all around the map
- block non-root vm86(old) if mmap_min_addr != 0
- two small debuggability improvements
- removal of obsolete paravirt op
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Fix Geode LX timekeeping in the generic x86 build
x86/apic: Serialize LVTT and TSC_DEADLINE writes
x86/ioapic: Force affinity setting in setup_ioapic_dest()
x86/paravirt: Remove the unused pv_time_ops::get_tsc_khz method
x86/ldt: Fix small LDT allocation for Xen
x86/vm86: Fix the misleading CONFIG_VM86 Kconfig help text
x86/cpu: Print family/model/stepping in hex
x86/vm86: Block non-root vm86(old) if mmap_min_addr != 0
x86/alternatives: Make optimize_nops() interrupt safe and synced
x86/mm/srat: Print non-volatile flag in SRAT
x86/cpufeatures: Enable cpuid for Intel SHA extensions
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A fix for an abs()/abs64() bug that caused too slow NTP convergence on
32-bit kernels, plus a removal of an obsolete clockevents driver
facility after all users got converted during the merge window"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Remove unused set_mode() callback
time: Fix timekeeping_freqadjust()'s incorrect use of abs() instead of abs64()
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo MOlnar:
"Mostly tooling fixes, but also two x86 PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tests: Fix software clock events test setting maps
perf tests: Fix task exit test setting maps
perf evlist: Fix create_syswide_maps() not propagating maps
perf evlist: Fix add() not propagating maps
perf evlist: Factor out a function to propagate maps for a single evsel
perf evlist: Make create_maps() use set_maps()
perf evlist: Make set_maps() more resilient
perf evsel: Add own_cpus member
perf evlist: Fix missing thread_map__put in propagate_maps()
perf evlist: Fix splice_list_tail() not setting evlist
perf evlist: Add has_user_cpus member
perf evlist: Remove redundant validation from propagate_maps()
perf evlist: Simplify set_maps() logic
perf evlist: Simplify propagate_maps() logic
perf top: Fix segfault pressing -> with no hist entries
perf header: Fixup reading of HEADER_NRCPUS feature
perf/x86/intel: Fix constraint access
perf/x86/intel/bts: Set event->hw.itrace_started in pmu::start to match the new logic
perf tools: Fix use of wrong event when processing exit events
perf tools: Fix parse_events_add_pmu caller
We are the client, but advertise keepalive2 anyway - for consistency,
if nothing else. In the future the server might want to know whether
its clients support keepalive2.
wraps ceph_ts into a kvec and adds it to con->out_kvec array, yet
ceph_ts becomes invalid on return from prepare_write_keepalive(). As
a result, we send out bogus keepalive2 stamps. Fix this by encoding
into a ceph_timespec member, similar to how acks are read and written.
Ming Lei [Thu, 17 Sep 2015 16:06:28 +0000 (00:06 +0800)]
block: fix bounce_end_io
When bio bounce is involved, one new bio and its biovecs are
cloned from the comming bio, which can be one fast-cloned bio
from upper layer(such as dm).
So it is obviously wrong to assume the start index of the coming(
original) bio's io vector is zero, which can be any value between
0 and (bi_max_vecs - 1), especially in case of bio split.
This patch fixes Fedora's booting oops on i386, often with the
following kernel log together:
> [ 9.026738] systemd[1]: Switching root.
> [ 9.036467] systemd-journald[149]: Received SIGTERM from PID 1
> (systemd).
> [ 9.082262] BUG: Bad page state in process kworker/u5:1 pfn:372ac
> [ 9.083989] page:f3d32ae0 count:0 mapcount:0 mapping:f2252178
> index:0x16a
> [ 9.085755] flags: 0x40020021(locked|lru|mappedtodisk)
> [ 9.087284] page dumped because: page still charged to cgroup
> [ 9.088772] bad because of flags:
> [ 9.089731] flags: 0x21(locked|lru)
> [ 9.090818] page->mem_cgroup:f2c3e400
Reported-by: Josh Boyer <jwboyer@fedoraproject.org> Tested-by: Adam Williamson <awilliam@redhat.com> Cc: Ming Lin <mlin@kernel.org> Cc: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Thu, 17 Sep 2015 15:58:38 +0000 (09:58 -0600)]
block: blk-merge: fast-clone bio when splitting rw bios
biovecs has become immutable since v3.13, so it isn't necessary
to allocate biovecs for the new cloned bios, then we can save
one extra biovecs allocation/copy, and the allocation is often
not fixed-length and a bit more expensive.
For example, if the 'max_sectors_kb' of null blk's queue is set
as 16(32 sectors) via sysfs just for making more splits, this patch
can increase throught about ~70% in the sequential read test over
null_blk(direct io, bs: 1M).
Cc: Christoph Hellwig <hch@infradead.org> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Ming Lin <ming.l@ssi.samsung.com> Cc: Dongsu Park <dpark@posteo.net> Signed-off-by: Ming Lei <ming.lei@canonical.com>
This fixes a performance regression introduced by commit 54efd50bfd,
and allows us to take full advantage of the fact that we have immutable
bio_vecs. Hand applied, as it rejected violently with commit 5014c311baa2.
Ross Zwisler [Wed, 16 Sep 2015 20:52:21 +0000 (14:52 -0600)]
pmem: add proper fencing to pmem_rw_page()
pmem_rw_page() needs to call wmb_pmem() on writes to make sure that the
newly written data is durable. This flow was added to pmem_rw_bytes()
and pmem_make_request() with this commit:
commit 61031952f4c8 ("arch, x86: pmem api for ensuring durability of
persistent memory updates")
...the pmem_rw_page() path was missed.
Cc: <stable@vger.kernel.org> Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Spinlock performance regression fix, plus documentation fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/static_keys: Fix up the static keys documentation
locking/qspinlock/x86: Only emit the test-and-set fallback when building guest support
locking/qspinlock/x86: Fix performance regression under unaccelerated VMs
locking/static_keys: Fix a silly typo
Paolo Bonzini [Thu, 17 Sep 2015 14:51:59 +0000 (16:51 +0200)]
Merge tag 'kvm-arm-for-4.3-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
Second set of KVM/ARM changes for 4.3-rc2
- Workaround for a Cortex-A57 erratum
- Bug fix for the debugging infrastructure
- Fix for 32bit guests with more than 4GB of address space
on a 32bit host
- A number of fixes for the (unusual) case when we don't use
the in-kernel GIC emulation
- Removal of ThumbEE handling on arm64, since these have been
dropped from the architecture before anyone actually ever
built a CPU
- Remove the KVM_ARM_MAX_VCPUS limitation which has become
fairly pointless
x86/pci/dma: Fix gfp flags for coherent DMA memory allocation
Commit 6894258eda2f reversed the order of gfp_flags adjustment in
dma_alloc_attrs() for x86 [arch/x86/kernel/pci-dma.c] As a result,
relevant flags set by dma_alloc_coherent_gfp_flags() are just
discarded and cause coherent DMA memory allocation failure on some
devices.
Fixes: 6894258eda2f ("dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}") Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Tested-by: Tony Luck <tony.luck@intel.com> Acked-by: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/20150914073834.GA13077@xzibit.linux.bs1.fc.nec.co.jp Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Ming Lei [Wed, 2 Sep 2015 06:31:21 +0000 (14:31 +0800)]
arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
This patch removes config option of KVM_ARM_MAX_VCPUS,
and like other ARCHs, just choose the maximum allowed
value from hardware, and follows the reasons:
1) from distribution view, the option has to be
defined as the max allowed value because it need to
meet all kinds of virtulization applications and
need to support most of SoCs;
2) using a bigger value doesn't introduce extra memory
consumption, and the help text in Kconfig isn't accurate
because kvm_vpu structure isn't allocated until request
of creating VCPU is sent from QEMU;
3) the main effect is that the field of vcpus[] in 'struct kvm'
becomes a bit bigger(sizeof(void *) per vcpu) and need more cache
lines to hold the structure, but 'struct kvm' is one generic struct,
and it has worked well on other ARCHs already in this way. Also,
the world switch frequecy is often low, for example, it is ~2000
when running kernel building load in VM from APM xgene KVM host,
so the effect is very small, and the difference can't be observed
in my test at all.
Cc: Dann Frazier <dann.frazier@canonical.com> Signed-off-by: Ming Lei <ming.lei@canonical.com> Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Will Deacon [Tue, 15 Sep 2015 16:15:33 +0000 (17:15 +0100)]
arm64: KVM: Remove all traces of the ThumbEE registers
Although the ThumbEE registers and traps were present in earlier
versions of the v8 architecture, it was retrospectively removed and so
we can do the same.
Whilst this breaks migrating a guest started on a previous version of
the kernel, it is much better to kill these (non existent) registers
as soon as possible.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
[maz: added commend about migration] Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Wed, 16 Sep 2015 15:18:59 +0000 (16:18 +0100)]
arm: KVM: Disable virtual timer even if the guest is not using it
When running a guest with the architected timer disabled (with QEMU and
the kernel_irqchip=off option, for example), it is important to make
sure the timer gets turned off. Otherwise, the guest may try to
enable it anyway, leading to a screaming HW interrupt.
The fix is to unconditionally turn off the virtual timer on guest
exit.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Wed, 16 Sep 2015 15:18:59 +0000 (16:18 +0100)]
arm64: KVM: Disable virtual timer even if the guest is not using it
When running a guest with the architected timer disabled (with QEMU and
the kernel_irqchip=off option, for example), it is important to make
sure the timer gets turned off. Otherwise, the guest may try to
enable it anyway, leading to a screaming HW interrupt.
The fix is to unconditionally turn off the virtual timer on guest
exit.
Cc: stable@vger.kernel.org Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This config option is completely irrelevant for zfcpdump and
unfortunately causes a kernel panic on recent kernels in
"mspro_block_init()/driver_register()".
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The scaled cputime is supposed to be derived from the normal per-thread
cputime by dividing it with the average thread density in the last interval.
The calculation of the scaling values for the average thread density is
incorrect. The current, incorrect calculation:
Ci = cycle count with i active threads
T = unscaled cputime, sT = scaled cputime
sT = T * (C1 + C2 + ... + Cn) / (1*C1 + 2*C2 + ... + n*Cn)
The calculation happens to yield the correct numbers for the simple cases
with only one Ci value not zero. But for cases with multiple Ci values not
zero it fails. E.g. on a SMT-2 system with one thread active half the time
and two threads active for the other half of the time it fails, the scaling
factor should be 3/4 but the formula gives 2/3.
The correct formula is
sT = T * (C1/1 + C2/2 + ... + Cn/n) / (C1 + C2 + ... + Cn)
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/cpum_cf: Corrected return code for unauthorized counter sets
Previously, the cpum_cf PMU returned -EPERM if a counter is requested and
the counter set to which the counter belongs is not authorized. According
to the perf_event_open() system call manual, an error code of EPERM indicates
an unsupported exclude setting or CAP_SYS_ADMIN is missing.
Use ENOENT to indicate that particular counters are not available when the
counter set which contains the counter is not authorized. For generic events,
this might trigger a fall back, for example, to a software event.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/compat: correct uc_sigmask of the compat signal frame
The uc_sigmask in the ucontext structure is an array of words to keep
the 64 signal bits (or 1024 if you ask glibc but the kernel sigset_t
only has 64 bits).
For 64 bit the sigset_t contains a single 8 byte word, but for 31 bit
there are two 4 byte words. The compat signal handler code uses a
simple copy of the 64 bit sigset_t to the 31 bit compat_sigset_t.
As s390 is a big-endian architecture this is incorrect, the two words
in the 31 bit sigset_t array need to be swapped.
Cc: <stable@vger.kernel.org> Reported-by: Stefan Liebler <stli@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The critical section cleanup code misses to add the offset of the
thread_struct to the task address.
Therefore, if the critical section code gets executed, it may corrupt
the task struct or restore the contents of the floating point registers
from the wrong memory location.
Fixes d0164ee20d "s390/kernel: remove save_fpu_regs() parameter and use
__LC_CURRENT instead".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/hibernate: fix save and restore of vector registers
The swsusp_arch_suspend()/swsusp_arch_resume() functions currently only
save and restore the floating point registers. If the task that started
the hibernation process is using vector registers they can get lost.
To fix this just call save_fpu_regs in swsusp_arch_suspend(), the restore
will happen automatically on return to user space.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Will Deacon [Tue, 17 Mar 2015 12:15:02 +0000 (12:15 +0000)]
arm64: errata: add module build workaround for erratum #843419
Cortex-A53 processors <= r0p4 are affected by erratum #843419 which can
lead to a memory access using an incorrect address in certain sequences
headed by an ADRP instruction.
There is a linker fix to generate veneers for ADRP instructions, but
this doesn't work for kernel modules which are built as unlinked ELF
objects.
This patch adds a new config option for the erratum which, when enabled,
builds kernel modules with the mcmodel=large flag. This uses absolute
addressing for all kernel symbols, thereby removing the use of ADRP as
a PC-relative form of addressing. The ADRP relocs are removed from the
module loader so that we fail to load any potentially affected modules.
Cc: <stable@vger.kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Tue, 15 Sep 2015 11:07:06 +0000 (12:07 +0100)]
arm64: compat: fix vfp save/restore across signal handlers in big-endian
When saving/restoring the VFP registers from a compat (AArch32)
signal frame, we rely on the compat registers forming a prefix of the
native register file and therefore make use of copy_{to,from}_user to
transfer between the native fpsimd_state and the compat_vfp_sigframe.
Unfortunately, this doesn't work so well in a big-endian environment.
Our fpsimd save/restore code operates directly on 128-bit quantities
(Q registers) whereas the compat_vfp_sigframe represents the registers
as an array of 64-bit (D) registers. The architecture packs the compat D
registers into the Q registers, with the least significant bytes holding
the lower register. Consequently, we need to swap the 64-bit halves when
converting between these two representations on a big-endian machine.
This patch replaces the __copy_{to,from}_user invocations in our
compat VFP signal handling code with explicit __put_user loops that
operate on 64-bit values and swap them accordingly.
Cc: <stable@vger.kernel.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
projects / linux-beck.git / log