drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
The original line,
WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/mgag200: Don't change unrelated registers during modeset
Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Tested-by: Julia Lemire <jlemire@matrox.com> Acked-by: Julia Lemire <jlemire@matrox.com> Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Lespiau, Damien [Fri, 10 May 2013 12:36:44 +0000 (12:36 +0000)]
drm: Only print a debug message when the polled connector has changed
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Damien Lespiau [Wed, 8 May 2013 16:03:32 +0000 (17:03 +0100)]
drm: Don't prune modes loudly when a connector is disconnected
drm_helper_probe_single_connector_modes() is responsible for pruning the
previously detected modes on a disconnected connector. We don't really
need to log, again, the full list of modes that used to be valid when
connected.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 10 May 2013 04:35:48 +0000 (14:35 +1000)]
Merge branch 'for-linux-next' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
Daniel writes:
A few intel fixes for smaller issues and one revert for an sdv hack which
we've wanted to kill anyway. Plus two drm patches included for your
convenience, both regression fixers for mine own screw-ups.
+ both fixes for stolen mem handling.
* 'for-linux-next' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=57191 Reported-and-tested-by: Nikolay Amiantov <nikoamia@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org (3.9 only) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This revert requires a bit of explanation on how I understand things
work. Internally the architects/designers decide how the stolen encoding
works. We put it in a doc. BIOS writers take these docs and implement
it. Driver writers read the doc too, and read the value left by the BIOS
writers, and then we make magic.
The failing here is that in the docs we had[1] contained two different
definitions for this register for Gen7. (We have both a PCI register,
and an MMIO, and each of these were different). At the time [2] of 03752f5, we asked the architects what the correct value should be; but
that doesn't match the reality (BIOS) unfortunately.
So on all machines I can get my hands on, this revert is the right thing
to do. I've also worked with the product group to confirm that they
agree this revert is what we should do. People using HW made my "people"
who both write their own BIOS, and have access to our docs (Apple?).
Investigations are still ongoing about whether we need to add a list
of machines needing special handling, but this patch should be the
right thing for pretty much everyone.
[1] The docs are still wrong on this one. Now instead of two registers with
two definitions, we have one register with BOTH definitions, progress?
[2] The open source PRMs have the "wrong" definitions in chapter Volume
1 part6, section 1.1.12.
This digging was inspired by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Augment the patch saying that it's still a bit unclear
whether there are any machines out there with "wrong" firmware and
whether we need to add a list to handle them specially.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Fri, 3 May 2013 09:57:41 +0000 (12:57 +0300)]
drm/i915: hsw: fix link training for eDP on port-A
According to BSpec the link training sequence for eDP on HSW port-A
should be as follows:
1. link training: clock recovery
2. link training: equalization
3. link training: set idle transmission mode
4. display pipe enable
5. link training: disable (set normal mode)
Contrary to this at the moment we don't do step 3. and we do step 5.
before step 4. Fix this by setting idle transmission mode for eDP at
the end of intel_dp_complete_link_train and adding a new
intel_dp_stop_link_training function to disable link training. With
these changes we'll end up with the following functions corresponding
to the above steps:
For port-A we'll call intel_dp_stop_link_train only after enabling the
pipe, for everything else we'll call it right after
intel_dp_complete_link_train to preserve the current behavior.
Tested on HSW/HSW-ULT.
In v2:
- Due to a HW issue we must set idle transmission mode for port-A too
before enabling the pipe. Thanks for Arthur Runyan for explaining
this.
- Update the patch subject to make it clear that it's an eDP fix, DP is
not affected.
v3:
- rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val'
instead 'l' as var name. (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's an ugly hack for a Haswell SDV platform where the vbt doesn't
seem to fully agree with the panel. Since it seems to cause issues on
real eDP platform let's just kill this hack again.
Reported-and-tested-by: Josh Boyer <jwboyer@gmail.com>
References: https://lkml.org/lkml/2013/5/3/467 Cc: Paulo Zanoni <przanoni@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Fri, 3 May 2013 00:13:08 +0000 (10:13 +1000)]
Merge branch 'server-fixes' into drm-next
Merge the fixes for the server driver dirty update paths
* server-fixes:
drm/cirrus: deal with bo reserve fail in dirty update path
drm/ast: deal with bo reserve fail in dirty update path
drm/mgag200: deal with bo reserve fail in dirty update path
Dave Airlie [Fri, 3 May 2013 00:10:23 +0000 (10:10 +1000)]
Merge tag 'omapdss-for-3.10-fixes' of git://gitorious.org/linux-omap-dss2/linux into drm-next
OMAPDSS fixes for 3.10:
* Compilation fix when DSI is disabled in Kconfig
* Basic deferred probe support to fix DT boot
* tag 'omapdss-for-3.10-fixes' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
OMAPDSS: VENC: use platform_driver_register()
OMAPDSS: HDMI: use platform_driver_register()
OMAPDSS: RFBI: use platform_driver_register()
OMAPDSS: DSI: use platform_driver_register()
OMAPDSS: SDI: use platform_driver_register()
OMAPDSS: DPI: use platform_driver_register()
OMAPFB: defer probe if no displays
OMAPFB: use module_platform_driver()
OMAPDSS: Makefile: move omapfb after panels
OMAPDSS: DPI: fix compilation if DSI not compiled in
Dave Airlie [Fri, 3 May 2013 00:09:11 +0000 (10:09 +1000)]
Merge branch 'drm-next-3.10-2' of git://people.freedesktop.org/~agd5f/linux into drm-next
Just some fixes that have accumulated over the last couple of
weeks and some new PCI ids.
* 'drm-next-3.10-2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
This is to allow debugging of userspace program not freeing buffer
after, which is basicly a memory leak. This print the list of all
gem object along with their size and placement (VRAM,GTT,CPU) and
with the pid of the task that created them.
agd5f: add warning fix
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tomi Valkeinen [Thu, 2 May 2013 09:19:54 +0000 (12:19 +0300)]
OMAPDSS: VENC: Add error handling for venc_probe_pdata
Add proper error handling for venc_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the VENC driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 26 Apr 2013 11:52:23 +0000 (14:52 +0300)]
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
Add proper error handling for hdmi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the HDMI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 2 May 2013 09:15:31 +0000 (12:15 +0300)]
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
Add proper error handling for rfbi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the RFBI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 26 Apr 2013 10:47:41 +0000 (13:47 +0300)]
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
Add proper error handling for dsi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DSI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 2 May 2013 09:10:37 +0000 (12:10 +0300)]
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
Add proper error handling for sdi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the SDI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 26 Apr 2013 11:33:05 +0000 (14:33 +0300)]
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
Add proper error handling for dpi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DPI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 26 Apr 2013 10:40:36 +0000 (13:40 +0300)]
OMAPFB: defer probe if no displays
omapfb requires the panel drivers to have been probed when omapfb is
initialized. omapfb does not support insertion of new panels after its
probe. This causes a problem in case omapdss or the panel probes have
been deferred due to EPROBE_DEFER error, as omapfb won't find any
displays.
As a quick fix, this patch changes the omapfb probe so that if omapfb
does not find any displays, it'll return EPROBE_DEFER. This is not
perfect, as with a board with no displays, omapfb will get deferred
forever. Also, if the board has multiple displays, but only some of them
have been probed, omapfb will start and leave the unprobed displays out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 26 Apr 2013 10:35:50 +0000 (13:35 +0300)]
OMAPDSS: Makefile: move omapfb after panels
omapfb requires the panels to have been probed before omapfb's probe. We
currently manage that by having omapfb in late initcall level. However,
a much simpler way is to just change the makefile so that omapfb is
after the panel drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 18 Apr 2013 09:16:39 +0000 (12:16 +0300)]
OMAPDSS: DPI: fix compilation if DSI not compiled in
Commit 100c826235793345efe06b3558cc9d36166b1e26 (OMAPDSS: DPI: use new
clock calculation code) breaks dpi.c compilation if DSI is not enabled
in the kernel configuration.
Fix compilation by adding dummy inline functions for the ones that dpi.c
references. The functions will never be called, as dpi.c knows that
there is no DSI device available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dave Airlie [Thu, 2 May 2013 07:33:25 +0000 (17:33 +1000)]
Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
Add GK110 modesetting suport.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nve0: recognise nvf0 as a kepler board (GK110)
drm/nouveau: force noaccel when no PFIFO support present
drm/nvf0/disp: expose display class 2.2
Dave Airlie [Thu, 2 May 2013 06:45:02 +0000 (02:45 -0400)]
drm/cirrus: deal with bo reserve fail in dirty update path
Port over the mgag200 fix to cirrus as it suffers the same issue.
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 2 May 2013 06:40:25 +0000 (02:40 -0400)]
drm/ast: deal with bo reserve fail in dirty update path
Port over the mgag200 fix to ast as it suffers the same issue.
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 2 May 2013 04:52:01 +0000 (00:52 -0400)]
drm/mgag200: deal with bo reserve fail in dirty update path
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Thu, 21 Mar 2013 11:10:44 +0000 (13:10 +0200)]
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
Fix the incorrect enabled pipes mask for pipe C in the WM calculations.
Additionally, in an effort to make the code easier to understand,
populate the mask with 1 << PIPE_[ABC] instead of raw numbers.
v2: Use 1 << PIPE_[ABC] (ickle/danvet)
v3: Pass PIPE_[ABC] to g4x_compute_wm0() (ickle)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 24 Apr 2013 16:04:57 +0000 (19:04 +0300)]
drm/prime: warn for non-empty handle lookup list during drm file release
drm_gem_release should release all handles connected to the drm file and
so should also release the prime lookup entries of these handles. So
just WARN if this isn't the case.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Imre Deak [Fri, 19 Apr 2013 01:11:56 +0000 (11:11 +1000)]
drm: prime: fix refcounting on the dmabuf import error path
In commit be8a42ae60 we inroduced a refcount problem, where on the
drm_gem_prime_fd_to_handle() error path we'll call dma_buf_put() for
self imported dma buffers.
Fix this by taking a reference on the dma buffer in the .gem_import
hook instead of assuming the caller had taken one. Besides fixing the
bug this is also more logical.
Signed-off-by: Imre Deak <imre.deak@intel.com> Cc: stable@vger.kernel.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sun, 21 Apr 2013 23:54:36 +0000 (09:54 +1000)]
drm/prime: keep a reference from the handle to exported dma-buf (v6)
Currently we have a problem with this:
1. i915: create gem object
2. i915: export gem object to prime
3. radeon: import gem object
4. close prime fd
5. radeon: unref object
6. i915: unref object
i915 has an imported object reference in its file priv, that isn't
cleaned up properly until fd close. The reference gets added at step 2,
but at step 6 we don't have enough info to clean it up.
The solution is to take a reference on the dma-buf when we export it,
and drop the reference when the gem handle goes away.
So when we export a dma_buf from a gem object, we keep track of it
with the handle, we take a reference to the dma_buf. When we close
the handle (i.e. userspace is finished with the buffer), we drop
the reference to the dma_buf, and it gets collected.
This patch isn't meant to fix any other problem or bikesheds, and it doesn't
fix any races with other scenarios.
v1.1: move export symbol line back up.
v2: okay I had to do a bit more, as the first patch showed a leak
on one of my tests, that I found using the dma-buf debugfs support,
the problem case is exporting a buffer twice with the same handle,
we'd add another export handle for it unnecessarily, however
we now fail if we try to export the same object with a different gem handle,
however I'm not sure if that is a case I want to support, and I've
gotten the code to WARN_ON if we hit something like that.
v2.1: rebase this patch, write better commit msg.
v3: cleanup error handling, track import vs export in linked list,
these two patches were separate previously, but seem to work better
like this.
v4: danvet is correct, this code is no longer useful, since the buffer
better exist, so remove it.
v5: always take a reference to the dma buf object, import or export.
(Imre Deak contributed this originally)
v6: square the circle, remove import vs export tracking now
that there is no difference
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
drm: Introduce an iterator over holes in the drm_mm range manager
helpers and iterators for hole handling have been introduced with some
debug BUG_ONs sprinkled over. Unfortunately this broke the mm dumper
which unconditionally tried to compute the size of the very first
hole.
While at it unify the code a bit with the hole dumping in the loop.
v2: Extract a hole dump helper.
Reported-by: Christopher Harvey <charvey@matrox.com> Cc: Christopher Harvey <charvey@matrox.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org Acked-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 26 Apr 2013 13:22:46 +0000 (16:22 +0300)]
drm/i915: Always normalize return timeout for wait_timeout_ioctl
As we recompute the remaining timeout after waiting, there is a
potential for that timeout to be less than zero and so need sanitizing.
The timeout is always returned to userspace and validated, so we should
always perform the sanitation.
v2 [vsyrjala]: Only normalize the timespec if it's invalid
v3: Add a comment to clarify the situation and remove the now
useless WARN_ON() (ickle)
Cc: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 26 Apr 2013 14:40:28 +0000 (17:40 +0300)]
drm: Kill user_modes list and the associated ioctls
There is no way to use modes added to the user_modes list. We never
look at the contents of said list in the kernel, and the only operations
userspace can do are attach and detach. So the only "benefit" of this
interface is wasting kernel memory.
Fortunately it seems no real user space application ever used these
ioctls. So just kill them.
Also remove the prototypes for the non-existing drm_mode_addmode_ioctl()
and drm_mode_rmmode_ioctl() functions.
v2: Use drm_noop instead of completely removing the ioctls
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Thu, 25 Apr 2013 17:09:20 +0000 (20:09 +0300)]
drm: Silence some sparse warnings
drivers/gpu/drm/drm_pci.c:155:5: warning: symbol 'drm_pci_set_busid' was not declared. Should it be static?
drivers/gpu/drm/drm_pci.c:197:5: warning: symbol 'drm_pci_set_unique' was not declared. Should it be static?
drivers/gpu/drm/drm_pci.c:269:5: warning: symbol 'drm_pci_agp_init' was not declared. Should it be static?
drivers/gpu/drm/drm_crtc.c:181:1: warning: symbol 'drm_get_dirty_info_name' was not declared. Should it be static?
drivers/gpu/drm/drm_crtc.c:1123:5: warning: symbol 'drm_mode_group_init' was not declared. Should it be static?
drivers/gpu/drm/drm_modes.c:918:6: warning: symbol 'drm_mode_validate_clocks' was not declared. Should it be static?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Rientjes [Sun, 28 Apr 2013 21:09:25 +0000 (14:09 -0700)]
drivers, drm: fix qxl build error when debugfs is disabled
Fix build error when CONFIG_DEBUG_FS is disabled:
drivers/gpu/drm/qxl/qxl_debugfs.c: In function 'qxl_debugfs_init':
drivers/gpu/drm/qxl/qxl_debugfs.c:76:2: error: implicit declaration of function 'drm_debugfs_create_files'
drivers/gpu/drm/qxl/qxl_debugfs.c: In function 'qxl_debugfs_takedown':
drivers/gpu/drm/qxl/qxl_debugfs.c:84:2: error: implicit declaration of function 'drm_debugfs_remove_files'
Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 29 Apr 2013 23:58:17 +0000 (09:58 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
Just a few important fixes for 3.10. 3 regression fixes, plus rectified
Haswell overclock support (the old code was correct, only docs confusing)
and improved DP data m/n selection.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: correct the calculation of first_pd_entry_in_global_pt
Revert "drm/i915: Don't overclock on Haswell"
drm/i915: Make data/link N value power of two
drm/i915: avoid full modeset when changing the color range properties
drm/i915: Fall back to bit banging mode for DVO transmitter detection
Dave Airlie [Mon, 29 Apr 2013 23:57:46 +0000 (09:57 +1000)]
Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
This is final pull request for Exynos next and includes device tree
support for fimc device, one revert, some code cleanups and fixup.
The revert replaces wrong one[1] with correct one[2].
This was my mistake and sorry for this.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Don't blend mixer layer 0
drm/exynos: Remove unnecessary braces in exynos_hdmi.c
drm/exynos: Select VIDEOMODE_HELPERS for FIMD
drm/exynos: do not use generic flags to dumb
drm/exynos: added ipp device registration to drm driver
exynos/drm: hdmi: cleanup for hdmi common device registration
drm/exynos: fix wrong return check for platform_device_register_simple
drm/exynos: add device tree support for fimc ipp driver
drm/exynos: rework fimc clocks handling
drm/exynos: remove redundant devm_kfree()
drm/exynos: enable FIMD clocks
Revert "drm/exynos: prepare FIMD clocks"
Sean Paul [Thu, 25 Apr 2013 19:13:26 +0000 (15:13 -0400)]
drm/exynos: Don't blend mixer layer 0
This patch disables blending the mixer's layer 0 onto the background
(solid color). It doesn't make sense to blend this layer by default,
and causes color distortion if the layer is used for arbitrary content.
Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Inki Dae <inki.dae@samsung.com>
FIMD also requires video mode helper APIs.
Without this patch we get the following build error:
drivers/gpu/drm/exynos/exynos_drm_fimd.c:895: undefined reference to
`of_get_fb_videomode'
make: *** [vmlinux] Error 1
Seung-Woo Kim [Tue, 23 Apr 2013 05:02:53 +0000 (14:02 +0900)]
drm/exynos: added ipp device registration to drm driver
This patch added exynos-drm-ipp platform device registration to the exynos drm
driver. When DT is enabled, platform devices need to be registered within the
driver code. This patch fits the requirement of both DT and Non DT based drm
drivers.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Seung-Woo Kim [Mon, 22 Apr 2013 09:40:34 +0000 (18:40 +0900)]
exynos/drm: hdmi: cleanup for hdmi common device registration
The hdmi common device registration function does not need extern definition
and for error case and unregister case, exynos_drm_hdmi_pdev should be cleared.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
drm/exynos: add device tree support for fimc ipp driver
This patch adds OF initialization support for the FIMC driver.
The binding documentation can be found at Documentation/devicetree/
bindings/media/samsung-fimc.txt.
The syscon regmap interface is used to serialize access to the
shared CAMBLK registers from within the V4L2 FIMC-IS and the DRM
FIMC drivers. The DRM driver uses this interface for setting up
the FIFO data link between FIMD and FIMC IP blocks, while the V4L2
one for setting up a data link between the camera ISP and FIMC for
camera capture. The CAMBLK registers are not accessed any more
through a statically mapped IO. Synchronized access to these
registers is required for simultaneous operation of the camera
ISP and the DRM IPP on Exynos4x12.
The driver data and driver_ids static data structures are removed
since Exynos4 is going to be a dt-only platform and there is
currently no board file in mainline that defines platform data
for the FIMC IPP, i.e. uses it.
Camera input signal polarities are not currently parsed from the
device tree.
The clocks handling is refactored and a "mux" clock handling is
added to account for changes in the clocks driver. After switching
to the common clock framework the sclk_fimc clock is now split
into two clocks: a gate and a mux clock. In order to retain the
exisiting functionality two additional consumer clocks are passed
to the driver from device tree: "mux" and "parent". Then the driver
sets "parent" clock as a parent clock of the "mux" clock. These two
additional clocks are optional, and should go away when there is a
standard way of setting up parent clocks on DT platforms.
There is no need for explicit calls of devm_kfree(), as
the allocated memory will be freed during driver's detach.
Remove the redundant devm_kfree() calls from probe() and
remove() callbacks.
Common Clock Framework introduced the need to prepare clocks before
enabling them, otherwise clk_enable() fails. This patch adds clk_prepare_enable
and clk_disable_unprepare() calls to the driver.
This patch also removes clk_disable() from fimd_remove() as it will be done
by pm_runtime_put_sync.
drm/i915: correct the calculation of first_pd_entry_in_global_pt
When ppgtt is enabled, dev_priv->gtt.total has excluded the gtt space
occupied by ppgtt table in i915_gem_init_global_gtt() function. So the
calculation of first_pd_entry_in_global_pt doesn't need to subtract
I915_PPGTT_PD_ENTRIES again. Or else PPGTT directory table will be
destroyed by global gtt allocation.
The breakage is pretty subtile since the old gtt_total_entries
included the pde range, whereas the new on did not.
Cc: stable@vger.kernel.org Signed-off-by: Xiong Zhang<xiong.y.zhang@intel.com>
[danvet: Add regression citation and cc: stable. Thanks to Chris for
correcting my wrong guess about which commit broke things.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Fri, 26 Apr 2013 05:42:02 +0000 (15:42 +1000)]
Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
"Nothing overly exciting here aside from calim's fermi/kepler vram
compression patches. The rest is misc fixes I gathered from the list.
Most of the stuff from me is fixing issues that have come up from the
work on kepler PM, as well as a commit moving all the old-school
modesetting out of the way (no code changes here). There's other
patches to go on top of that, but, it'll have to wait until I can rip
out the old PM code, it's a bit tangled."
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (38 commits)
drm/nouveau/fifo: implement channel creation event generation
drm/nouveau/core: allow non-maskable events
drm/nouveau/timer: allow alarms to be cancelled
drm/nouveau/device: tweak the device/subdev relationship a little
drm/nouveau/device: enable proper constructor/destructor
drm/nouveau/device: have engine object initialised before creation
drm/nouveau/device: convert to engine, rather than subdev
drm/nv50-/disp: use self as parent for subobjects
drm/nv50-/fifo: use parent as self for subobjects
drm/nv20-nv30/gr: use parent as self for subobjects
drm/nvc0-/gr: use self as parent for subobjects
drm/nv04-nv40/instmem: use self as parent for subobjects
drm/nv04-nv40/vm: use self as parent for subobjects
drm/nv50-/bar: use self as parent for subobjects
drm/nv04-nv40/instmem: remove parent deref hack
drm/nouveau/i2c: remove parent deref hack
drm/nouveau/core: rebase object ref/use counts after ctor/init/fini events
drm/nv50/disp: inform core when we're not creating a new context
drm/nouveau/therm: send some messages to debug level
drm/nve0/gr: add handling for a bunch of PGRAPH traps
...