Imre Deak [Mon, 14 Apr 2014 17:24:37 +0000 (20:24 +0300)]
drm/i915: make runtime PM interrupt enable/disable platform independent
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:36 +0000 (20:24 +0300)]
drm/i915: disable runtime PM if RC6 is disabled
On VLV we depend on RC6 to save the GT render and media HW context
before going to the D3 state via RPM, so as a preparation for the
VLV RPM support (added in an upcoming patch) disable RPM if RC6 is
disabled.
There is probably a similar dependency on other platforms too, so for
safety require RC6 for those too. For these platforms (SNB, HSW, BDW)
this is then a possible fix.
v2:
- require RC6 for all RPM platforms, not just for VLV (Paulo, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Fri, 18 Apr 2014 13:01:02 +0000 (16:01 +0300)]
drm/i915: sanitize enable_rc6 option
Atm, an invalid enable_rc6 module option will be silently ignored, so
emit an info message about it. Doing an early sanitization we can also
reuse intel_enable_rc6() in a follow-up patch to see if RC6 is actually
enabled. Currently the caller would have to filter a non-zero return
value based on the platform we are running on. For example on VLV with
i915.enable_rc6 set to 2, RC6 won't be enabled but atm
intel_enable_rc6() would still return 2 in this case.
v2:
- simplify the platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we call intel_gt_powersave_enable() for GEN6 and GEN7 but disable
it for everything starting from GEN6. This is a problem in case of BDW.
Since I don't have a BDW to test if RC6 works properly, just keep it
disabled for now and fix only the disable function.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:33 +0000 (20:24 +0300)]
drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Some platforms need additional power domains to be on in addition to the
device D0 state to access the panel registers.
Suggested by Daniel.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76987 Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Fri, 18 Apr 2014 12:55:04 +0000 (15:55 +0300)]
drm/i915: add missing error capturing of the PIPESTAT reg
While checking the error capture path I noticed that we lacked the
power domain-on check for PIPESTAT so fix this by moving that to where
the rest of pipe registers are captured.
The move also revealed that we actually don't include this register in
the error report, so fix that too.
v2:
- patch introduced in v2 of the patchset
v3:
- add back !HAS_PCH_SPLIT check (Ville)
[ Ignore my previous comment about the gen<=5 || vlv check, I realized
that it's the same as !HAS_PCH_SPLIT. ]
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:31 +0000 (20:24 +0300)]
drm/i915: gen2: move error capture of IER to its correct place
While checking the error capture path I noticed that this register is
read twice for GEN2, so fix this and also move the read where it's done
for other platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 22 Apr 2014 22:09:04 +0000 (01:09 +0300)]
drm/i915: get a runtime PM ref for the deferred GPU reset work
Atm we can end up in the GPU reset deferred work in D3 state if the last
runtime PM reference is dropped between detecting a hang/scheduling the
work and executing the work. At least one such case I could trigger is
the simulated reset via the i915_wedged debugfs entry. Fix this by
getting an RPM reference around accessing the HW in the reset work.
v2:
- Instead of getting/putting the RPM reference in the reset work itself,
get it already before scheduling the work. By this we also prevent
going to D3 before the work gets to run, in addition to making sure
that we run the work itself in D0. (Ville, Daniel)
v3:
- fix inverted logic fail when putting the RPM ref on behalf of a
cancelled GPU reset work (Ville)
v4:
- Taking the RPM ref in the interrupt handler isn't really needed b/c
it's already guaranteed that we hold an RPM ref until the end of the
reset work in all cases we care about. So take the ref in the reset
work (for cases like i915_wedged_set). (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 18 Apr 2014 21:04:22 +0000 (18:04 -0300)]
drm/i915: Validate VBT header before trusting it
Be we read and chase pointers from the VBT, it is prudent to make sure
that those accesses are wholly contained within the MMIO region, or else
we may cause a kernel panic during boot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 18 Apr 2014 21:04:23 +0000 (18:04 -0300)]
drm/i915: Validate BDB section before reading
Make sure that the whole BDB section is within the MMIO region prior to
accessing it contents. That we don't read outside of the secion is left
up to the individual section parsers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:29 +0000 (20:24 +0300)]
drm/i915: get a runtime PM ref for the deferred GT powersave enabling
At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.
v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:28 +0000 (20:24 +0300)]
drm/i915: move getting struct_mutex lower in the callstack during GPU reset
Getting struct_mutex around the whole intel_enable_gt_powersave()
function is not necessary, since it's only needed for the ILK path
therein.
This will make intel_enable_gt_powersave() useable on the RPM resume
path for >=GEN6 (added in an upcoming patch to reset the RPS state
during RPM resume), where we can't (and need not) get this mutex.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:27 +0000 (20:24 +0300)]
drm/i915: get a runtime PM ref for debugfs entries where needed
These debugfs entries access registers that need the D0 power state so
get an RPM ref for them.
v2:
- for all these entries we only need D0 state, so get only an RPM ref,
not a power domain ref (Daniel, Paulo)
- the dpio entry is not an issue any more as it got removed (Ville)
- restore commit message from v1 (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:26 +0000 (20:24 +0300)]
drm/i915: remove the i915_dpio debugfs entry
There are igt tools that can read/write the DPIO registers, so having a
debugfs entry for only some of those registers is somewhat arbitrary /
redundant. Remove it.
v2:
- instead of fixing the entry by taking a power domain reference around
the register accesses, remove the entry (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:25 +0000 (20:24 +0300)]
drm/i915: fix the RC6 status debug print
The parsing was incorrect for ILK and VLV.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:24 +0000 (20:24 +0300)]
drm/i915: vlv: add RC6 residency counters
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 14 Apr 2014 17:24:23 +0000 (20:24 +0300)]
drm/i915: vlv: clear master interrupt flag when disabling interrupts
Not clearing this flag causes spurious interrupts at least in D3 state,
so before enabling RPM we need to fix this. We were already setting this
flag when enabling interrupts, only clearing it was missing.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Use the coarse ping-pong mechanism based on drm fd to dispatch the BSD command on BDW GT3
The BDW GT3 has two independent BSD rings, which can be used to process the
video commands. To be simpler, it is transparent to user-space driver/middle.
Instead the kernel driver will decide which ring is to dispatch the BSD video
command.
As every BSD ring is powerful, it is enough to dispatch the BSD video command
based on the drm fd. In such case it can play back video stream while encoding
another video stream. The coarse ping-pong mechanism is used to determine
which BSD ring is used to dispatch the BSD video command.
V1->V2: Follow Daniel's comment and use the simple ping-pong mechanism.
This is only to add the support of dual BSD rings on BDW GT3 machine.
The further optimization will be considered in another patch set.
V2->V3: Follow Daniel's comment to use the struct_mutext instead of
atomic_t during determining which ring can be used to dispatch Video command.
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915:Add the VCS2 switch in Intel_ring_setup_status_page
The Gen7 doesn't have the second BSD ring. But it will complain the switch check
warning message during compilation. So just add it to remove the
switch check warning.
V1->V2: Follow Daniel's comment to update the comment
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Split the BDW device definition to prepare for dual BSD rings on BDW GT3
Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.
V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 24 Apr 2014 06:09:10 +0000 (08:09 +0200)]
drm/i915: Catch abuse of I915_EXEC_CONSTANTS_*
A bit tricky since 0 is also a valid constant ...
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/rel-constants-* Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 9 Apr 2014 08:19:44 +0000 (09:19 +0100)]
drm/i915: Include a little more information about why ring init fails
If we include the expected values for the failing ring register checks,
it makes it marginally easier to see which is the culprit.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 9 Apr 2014 08:19:43 +0000 (09:19 +0100)]
drm/i915: Mark device as wedged if we fail to resume
During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.
As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 9 Apr 2014 08:19:42 +0000 (09:19 +0100)]
drm/i915: Allow the module to load even if we fail to setup rings
Even without enabling the ringbuffers to allow command execution, we can
still control the display engines to enable modesetting. So make the
ringbuffer initialization failure soft, and mark the GPU as wedged
instead.
v2: Only treat an EIO from ring initialisation as a soft failure, and
abort module load for any other failure, such as allocation failures.
v3: Add an *ERROR* prior to declaring the GPU wedged so that it stands
out like a sore thumb in the logs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 9 Apr 2014 08:19:41 +0000 (09:19 +0100)]
drm/i915: Preserve ring buffers objects across resume
Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.
After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.
v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: Jae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 9 Apr 2014 08:19:40 +0000 (09:19 +0100)]
drm/i915: Replace hardcoded cacheline size with macro
For readibility and guess at the meaning behind the constants.
v2: Claim only the meagerest connections with reality.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: remove unexplained vblank wait in the DP off code
I don't think this is necessary; at least it doesn't appear to be on my
BYT. Dropping it speeds up our shutdown code a little, in some cases
resulting in faster init times.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 16 Apr 2014 14:56:09 +0000 (16:56 +0200)]
drm/i915: Remove vblank wait from haswell_write_eld
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Mar 2014 16:32:13 +0000 (18:32 +0200)]
drm/i915: Disable/enable planes as the first/last thing during modeset on ILK+
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 15 Apr 2014 16:41:22 +0000 (18:41 +0200)]
drm/i915: Don't vblank wait on ilk-ivb after pipe enable
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297 Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Add parsing support for new MIPI blocks in VBT
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 27 Jan 2014 09:00:30 +0000 (10:00 +0100)]
drm/i915: Don't set the 8to6 dither flag when not scaling
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue). Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Thu, 10 Apr 2014 21:32:41 +0000 (14:32 -0700)]
drm/i915/bdw: Add 42ms delay for IPS disable
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Parse EDID probed modes for DRRS support
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch duct-tapes over some issue in the current bdw rps patches
which must wait with enabling rc6/rps until the very first batch has
been submitted by userspace.
But those patches aren't merged yet, and for upstream we need to have
an in-kernel emission of the very first batch. I shouldn't have
merged this patch so let's revert it again.
Also Imre noticed that even when rps is set up normally there's a
small window (due to the 1s delay of the async rps init work) where we
could runtime suspend already and blow up all over the place. Imre has
a proper fix to block runtime pm until the rps init work has
successfully completed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Enable MIPI port before the plane and pipe enable
As per the hw team's recommendation we need to enable the MIPI port
before enabling the plane and pipe. So call MIPI port enable in
pre_enable phase itself
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
haswell_write_eld() is also used on broadwell, so let's not explicitely
mention Haswell. The rest of the function has plenty of debug output
which will print the function name, so we know where we are anyway.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 28 Mar 2014 16:18:18 +0000 (18:18 +0200)]
drm/i915: add flags to i915_ring_stop
Piglit runner and QA are both looking at the dmesg for
DRM_ERRORs with test cases. Add a flag to control those
when we they are expected from related test cases.
Also add flag to control if contexts should be banned
that introduced the hang. Hangcheck is timer based and
preventing bans by adding sleeps to testcases makes
testing slower.
References: https://bugs.freedesktop.org/show_bug.cgi?id=75876 Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 7 Apr 2014 20:01:47 +0000 (17:01 -0300)]
drm/i915: dma_buf_vunmap is presumed not to fail, don't let it
Since dma_buf_vunmap() procedes blithely on ignorant of whether the
driver failed to actually unmap the backing storage for the dma-buf, we
need to make a best-effort to do so. This involves not allowing
ourselves to be susceptible to signals causing us to leak the storage.
This should have been detectable with the current i-g-t as a misplaced
signal should have left the pages pinned upon freeing the object where
we have a warning in place.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Mar 2014 16:32:11 +0000 (18:32 +0200)]
drm/i916: Refactor WM register maximums
We will have another use for the maximum watermark values that the
registers can hold. Pull those out into separate functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Mar 2014 16:32:10 +0000 (18:32 +0200)]
drm/i915: Skip watermark merging for inactive pipes
Even though the inactive pipes should have their watermarks set to all 0
with enable=true, we can possibly shave off a few cycles by completely
skipping the merge procedure for inactive pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Mar 2014 16:32:09 +0000 (18:32 +0200)]
drm/i915: Add some more tracked state to intel_pipe_wm
intel_pipe_wm will be used to track the state in different stages
of the watermark update process. For that we need to keep a bit
more state in intel_pipe_wm.
We also need to separate the multi-pipe intel_wm_config computation
from ilk_compute_wm_parameters() as that one deals with the future
state, and we need the intel_wm_config to match the current hardware
state at the time we do the watermark merging for multiple pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Frob conflict.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sat, 5 Apr 2014 21:55:53 +0000 (14:55 -0700)]
drm/i915: Dump the whole context object.
As we've learned over time, the HW context is just a series of GPU
commands that we're able to decode without any changes in
intel_error_decode. Since many bugs recently have been implicated in
the HW context state, it makes sense to dump the whole context object
in a form which can be parsed.
Unfortunately, our decoder isn't quite smart enough to deal with the
variable length LRIs - but that is a tools problem.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Clarify commit message a bit, seems to have lost a few
crucial words.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Sat, 5 Apr 2014 05:41:07 +0000 (22:41 -0700)]
drm/i915: Unref context on failed eb_create
I opted to do this instead of grabbing the context reference after
eb_create since eb_create can potentially call the shrinker, and that
makes things very complicated. This simple patch balances the ref count
without requiring a great deal of review to make sure the shrinker path
is safe.
Theoretically (by design) the shrinker can end up destroying a context,
which enforces the reasoning for doing the fix this way instead of
moving the reference to later in the function.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Mar 2014 16:32:08 +0000 (18:32 +0200)]
drm/i915: Don't read sprite LP2+ registers on ILK/SNB
Sprite LP2+ registers don't exist on ILK/SNB so don't read them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 4 Apr 2014 13:36:10 +0000 (16:36 +0300)]
drm/i915: Make contexts non-snooped on non-LLC platforms
We don't do CPU access to GPU contexts so making the GPU access snoop
the CPU caches seems silly, and potentially expensive.
v2: Use !IS_VALLEYVIEW instead of HAS_LLC as this is really
about what the PTEs can represent.
Add a comment clarifying the situation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915/vlv:Implement the WA 'WaDisable_RenderCache_OperationalFlush'
On Gen4+ platforms (except BDW), Render Cache Operational flush
cannot be enabled.
This WA is apparently required for all Gen4+ platforms,except BDW.
In BDW, the bit has been repurposed otherwise.
This has been tested only on vlv.
v2: Corrected the code regarding the wrong usage of
MASKED_BIT_DISABLE (Chris)
v3: Enhancing the scope of WA to Gen4+ platforms except BDW (Ville)
v4: Adding WA for g4x, crestline, broadwater (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com> Signed-off-by: Sourab Gupta <sourab.gupta@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 9 Apr 2014 12:33:47 +0000 (14:33 +0200)]
Merge remote-tracking branch 'airlied/drm-next' into HEAD
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Russell King [Mon, 7 Apr 2014 11:00:17 +0000 (12:00 +0100)]
DRM: armada: fix corruption while loading cursors
Loading cursors to the LCD controller's SRAM can be corrupted when the
configured pixel clock is relatively slow. This seems to be caused
when we write back-to-back to the SRAM registers.
There doesn't appear to be any status register we can read to check
when an access has completed.
Inserting a dummy read between the writes appears to fix the problem.
Cc: <stable@vger.kernel.org> # 3.13 Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Sat, 5 Apr 2014 06:14:21 +0000 (16:14 +1000)]
Merge tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel into drm-next
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
Dave Airlie [Sat, 5 Apr 2014 06:13:08 +0000 (16:13 +1000)]
Merge tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.15-rc1
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
* tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Use standard GPL v2 license text
drm/tegra: Relicense under GPL v2
drm/tegra: Relicense public header under MIT
drm/tegra: Add eDP support
gpu: host1x: export host1x_syncpt_incr_max() function
drm/tegra: prime: Add vmap support
Dave Airlie [Sat, 5 Apr 2014 06:12:27 +0000 (16:12 +1000)]
Merge tag 'drm/panel/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.15-rc1
Add support for a couple more simple panels. A few cleanups to the
simple panel driver are also included (gpiod interface conversion,
removal of redundant call to regulator_disable()).
* tag 'drm/panel/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: add support for LG LD070WX3-SL01 panel
drm/panel: add support for LG LH500WX1-SD03 panel
drm/panel: simple: Allow DSI panels to provide mode flags
drm/panel: simple: Allow GPIO accesses to sleep
drm/panel: remove redundant regulator_disable()
drm/panel: use gpiod interface for enable GPIO
drm/panel: Add LG 12.9" LCD panel
MAINTAINERS: Add entry for DRM panel drivers
Dave Airlie [Sat, 5 Apr 2014 06:09:15 +0000 (16:09 +1000)]
Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Summaries:
- Add MIPI-DSI Driver, and dt bindigs
- Add S6E8AA0 MIPI-DSI based panel drivers, and dt bindings
- Add LD9040 parallel panel driver
. this driver is placed in drivers/gpu/drm/panel, and it seems
to be used for exynos drm as of now,
- Some fixups
Changelog v2:
- Remove super device support, and relevant dt bindings for more reviews.
- Fix module build errors you pointed out.
- Re-based it to drm-next again.
Dave Airlie [Sat, 5 Apr 2014 06:08:27 +0000 (16:08 +1000)]
Merge tag 'vmwgfx-next-2014-04-04' of git://people.freedesktop.org/~thomash/linux into drm-next
Pull request of 2014-04-04
The second vmwgfx pull request for the 3.15 merge window.
Contains a fbdev fix by Christopher Friedt, one fix for a locking order
violation introduced in 3.14 (hit when using queries) and finally a
removal of the DRM_AUTH requirement around some vmwgfx IOCTLS where the
caller is already required to have an open handle to the object.
* tag 'vmwgfx-next-2014-04-04' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: correct fb_fix_screeninfo.line_length
drm/vmwgfx: Remove authorization requirements around some more ioctls
drm/vmwgfx: Fix query buffer locking order violation
Andrzej Hajda [Thu, 3 Apr 2014 16:19:56 +0000 (01:19 +0900)]
drm/exynos: add DSIM driver
The patch adds driver for Exynos DSI master (DSIM). It is a platform driver
which is registered as exynos_drm_display sub-driver of exynos_drm framework
and implements DRM encoder/connector pair.
It is also MIPI-DSI host driver and provides DSI bus for panels.
It interacts with its panel(s) using drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 28 Mar 2014 11:52:39 +0000 (12:52 +0100)]
exynos/dsim: add DT bindings
The patch adds DT bindings for Exynos DSI Master. DSIM follows rules
for DSI bus host bindings [1].
Properties describes its resources: memory, interrupt, clocks,
phy, regulators, frequencies of clocks and video interfaces.
Andrzej Hajda [Fri, 28 Mar 2014 11:52:38 +0000 (12:52 +0100)]
drm/exynos: disallow fbdev initialization if no device is connected
This patch adds explicit check if there is a connector with
connected status before fbdev initialization. It prevents creation
of default fbdev 1024x768 which is unusable on panels with bigger resolutions.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
projects / karo-tx-linux.git / log