Wolfgang Denk [Sat, 27 Mar 2010 22:37:46 +0000 (23:37 +0100)]
mkimage: fix Segmentation Fault when run without "-n name" option
The restructuring of the mkimage command in commit 89a4d6b1 ("tools:
mkimage: split code into core, default and FIT image specific")
introduced a bug that caused mkimage to segfault when run without
"-n name" option. Initialize the imagename entry to prevent that.
Thomas Chou [Fri, 26 Mar 2010 00:17:00 +0000 (08:17 +0800)]
cfi flash: add status polling method for amd flash
This patch adds status polling method to offer an alternative to
data toggle method for amd flash chips.
This patch is needed for nios2 cfi flash interface, where the bus
controller performs 4 bytes read cycles for a single byte read
instruction. The data toggle method can not detect chip busy
status correctly. So we have to poll DQ7, which will be inverted
when the chip is busy.
This feature is enabled with the config def,
CONFIG_SYS_CFI_FLASH_STATUS_POLL
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Stefan Roese <sr@denx.de>
TsiChung Liew [Tue, 16 Mar 2010 17:39:36 +0000 (12:39 -0500)]
ColdFire: Fix m54455EVB save environment bug
The ATMEL flash does not have buffer write feature. Assgined
buffer_size = 1, so that when there is a write to the flash
will not use buffer write function.
TsiChung Liew [Thu, 11 Mar 2010 00:24:07 +0000 (18:24 -0600)]
ColdFire: Misc update for M53017
Reside Ethernet buffer descriptors in SRAM instead of DRAM. Add
CONFIG_SYS_TX_ETH_BUFFER in platform configuration file. Update
DRAM control and SRAM control register setting. Update cache
setting where size does not write to proper region.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com> Signed-off-by: Jason Jin <Jason.jin@freescale.com>
TsiChung Liew [Wed, 10 Mar 2010 22:14:01 +0000 (16:14 -0600)]
ColdFire: M5271EVB DRAM Bring up issue
Fix proper portsize: The register for portsize is either 00b, 01b,
or 1xb. The value that previous assigned is 32d.
Fix DRAM bring up: insert asm("nop") for every DRAM register setup
TsiChung Liew [Thu, 11 Mar 2010 21:04:21 +0000 (15:04 -0600)]
ColdFire: Relocate vector table - mcf5445x
Newer ColdFire processors family boot from address 0 instead of
0xFFnn_nnnn. When the boot flash base chip select is set at new
location instead of 0, an un-predictable error will occur if
there is an vector being trigger and refer it to an invalid
address or the vector table handler is not existed at address
0.
Wolfgang Wegner [Fri, 30 Oct 2009 15:55:02 +0000 (16:55 +0100)]
add block write function to spartan3 slave serial load
Using seperate function calls for each bit-bang of slave serial
load can be painfully slow. This patch adds the possibility to
supply a block write function that loads the complete block of
data in one call (like it can already be done with Altera FPGAs).
On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load
time from around 15 seconds to around 3 seconds
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
Rupjyoti Sarmah [Wed, 24 Mar 2010 11:22:02 +0000 (16:52 +0530)]
ppc4xx fix unstable 440EPx bootstrap options
440EPx fixed bootstrap options A, B, D, and E sets PLL FWDVA to a value = 1.
This results in the PLLOUTB being greater than the CPU clock frequency
resulting unstable 440EPx operation resulting in various software hang
conditions.
This patch reprograms the FWDVA satisfying the requirement of setting FWDVB
to a value greater than 1 while using one of the four deafult bootstrap options.
Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com>
Acked-by : Victor Gallardo <vgallardo@appliedmicro.com> Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Wed, 24 Mar 2010 09:16:20 +0000 (10:16 +0100)]
at91: Get rid of some warnings when building for otc570
The soft-i2c code for AT91 defines I2C_SOFT_DECLARATIONS
for direct access by dereferencing a pio pointer.
The OTC570 platform uses the AT91 gpio API so it does not
need the pio variable.
Florian Fainelli [Sat, 20 Mar 2010 18:02:58 +0000 (19:02 +0100)]
cmd_nand: show nand scrub confirmation character
When issuing a nand scrub command, the entered character is not displayed
this may be confusing. This patch makes the input character being
displayed if it is a 'y' so that an user knows he is about to scrub his
nand.
John Schmoller [Fri, 12 Mar 2010 15:49:24 +0000 (09:49 -0600)]
cmd history: Match history buffer size to console buffer
Match history buffer size to console buffer size. History buffer size
was hard coded to 256, artificially limiting the command buffer size.
The history buffer now tracks CONFIG_SYS_CBSIZE.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
John Schmoller [Fri, 12 Mar 2010 15:49:23 +0000 (09:49 -0600)]
console: Fix console buffer overrun
When CONFIG_SYS_CBSIZE equals MAX_CMDBUF_SIZE, a command string of
maximum length will overwrite part of the history buffer, causing the
board to die. Expand the console_buffer and hist_lines buffer by one
character each to hold the missing NULL char.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Michael Zaidman [Mon, 1 Mar 2010 09:47:36 +0000 (11:47 +0200)]
POST: add progress API
Add POST progress API implemented as weak calls before and after
each call to the POST test callback in the post_run_single routine
of the post.c file.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de>
cmd_setexpr: allow memory addresses in expressions
This patch add functionality to use memory addresses in expressions.
This increases the power of expressions substantially
It adheres to the standard convemtions: memory addresses can be given
in the format *address (e.g. *1000)
Rationale for this change is that it allows masking off bits from a
byte that is obtained by reading data from e.g. i2c.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Fix warning: control reaches end of non-void function Signed-off-by: Wolfgang Denk <wd@denx.de>
according to some of the comments the subaddress length is 1 or 2, but we are being
prepared for the case it becomes 3. However the code also accepted 4.
This repairs this by changing the constand 4 to 3.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Matthias Weisser [Tue, 12 Jan 2010 11:06:31 +0000 (12:06 +0100)]
video: Fix console display when splashscreen is used
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.
Jeff Angielski [Wed, 17 Mar 2010 19:09:26 +0000 (15:09 -0400)]
env: fix endian ordering in crc table
The crc table was being built as little endian for big endian
targets. This would cause fw_printenv to always fail with
"Warning: Bad CRC, using default environment" messages.
Signed-off-by: Jeff Angielski <jeff@theptrgroup.com> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fix warnings while compiling with CONFIG_VIDEO enabled:
diu.c: In function 'video_hw_init':
diu.c:158: warning: 'return' with no value, in function returning non-void
diu.c:162: warning: format '%ld' expects type 'long int', but argument 6 has type 'int'
diu.c:162: warning: format '%ld' expects type 'long int', but argument 7 has type 'int'
If a board uses cfb_console driver and splash image
and also defines CONFIG_SILENT_CONSOLE, the user is
locked out even if "silent" is not set. It is not
possible to get any output, neither on vga console
device nor on serial console after redirecting the
output to the serial console, since the GD_FLG_SILENT
flag remains set.
Fix the problem by redirecting the output from frame
buffer to serial console if splashimage is used.
Only suppress the output if "silent" environment
variable was set and don't set the GD_FLG_SILENT
flag arbitrarily.
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions. Signed-off-by: Wolfgang Denk <wd@denx.de>
Stefano Babic [Sat, 13 Mar 2010 20:09:00 +0000 (21:09 +0100)]
mxcmmc: fix warnings due to access 32 bit registers with 16 bit accessors
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.
Wolfgang Denk [Sun, 17 Jan 2010 22:55:53 +0000 (23:55 +0100)]
TFTP: allow for adjustable retransmission timout
So far, TFTP negotiated a fixed retransmission timeout of 5 seconds.
In some cases (busy networks, slow TFTP servers) this caused very
slow transfers. A new environment variable "tftptimeout" allows to
set this timeout. Lowering this value may make downloads succeed
faster in networks with high packet loss rates or with unreliable
TFTP servers.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Matthias Weisser [Tue, 12 Jan 2010 11:06:31 +0000 (12:06 +0100)]
video: Fix console display when splashscreen is used
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.
Wolfgang Denk [Fri, 12 Mar 2010 21:11:00 +0000 (22:11 +0100)]
standalone eepro100_eeprom: fix build error
Building examples/standalone/eepro100_eeprom triggers this error:
In file included from include/common.h:629,
from eepro100_eeprom.c:24:
include/net.h: In function 'NetReadIP':
include/net.h:430: warning: implicit declaration of function 'memcpy'
eepro100_eeprom.c: At top level:
eepro100_eeprom.c:81: error: conflicting types for 'memcpy'
include/net.h:430: error: previous implicit declaration of 'memcpy' was here
The length of configured MTDPARTS_DEFAULT string
could be greater than console printbuffer size.
Replace printf() by puts() to avoid potential buffer
overflows.
Wolfgang Denk [Thu, 11 Mar 2010 22:56:03 +0000 (23:56 +0100)]
Move CONFIG_UPDATE_TFTP code after CONFIG_PREBOOT
The auto-update feature (CONFIG_UPDATE_TFTP) requires that the env
variable serverip be set for the TFTP access. If DHCP is to be used
to get the serverip env variable, this doesn't work as DHCP happens
after the auto-update attempt has run. A solution is to run DHCP in
PREBOOT, but even this is too late.
To solve this, we move update_tftp() below the PREBOOT stuff.
Mike Frysinger [Mon, 25 Jan 2010 23:50:11 +0000 (18:50 -0500)]
mkimage: dont force entry point with xip
Some people boot images with the entry point in the middle of the blob
(like Linux with the head code in discardable .init.text), and there is no
no real requirement that the entry point be right after the mkimage header
when doing XIP, so let people specify whatever they want. If they do need
an entry right after the header, then they still can do that with normal
-e behavior.
Wolfgang Denk [Thu, 11 Mar 2010 22:35:43 +0000 (23:35 +0100)]
Fix memory leak in mmc_read()
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.
Reported-by: Quentin Armitage <Quentin@Armitage.org.uk> Signed-off-by: Wolfgang Denk <wd@denx.de>
Stefano Babic [Fri, 5 Mar 2010 16:54:37 +0000 (17:54 +0100)]
MX51: removed warnings for the mx51evk
The patch removes warnings at compile time and provides
some cleanup code:
- Removed comment on NAND (not yet supported) from lowlevel_init.S
- Removed NFMS bit definition from imx-regs.h
The bit is only related to MX.25/35 and can lead to confusion
- Moved is_soc_rev() to soc specific code (removed from mx51evk.c)
Heiko Schocher [Mon, 22 Feb 2010 11:13:02 +0000 (16:43 +0530)]
arm: add support for the suen3 board from keymile
Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.c
John Rigby [Tue, 26 Jan 2010 06:12:58 +0000 (23:12 -0700)]
Add support for KARO TX25 board
This is an i.MX25 base board with only NAND
so it uses nand_spl to boot.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Tune configuration, add support for (redundant) environment in NAND. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> CC: Fred Fan <fanyefeng@gmail.com> CC: Tom <Tom.Rix@windriver.com>
John Rigby [Tue, 26 Jan 2010 06:12:55 +0000 (23:12 -0700)]
fec_mxc: cleanup and factor out MX27 dependencies
general cleanup
move clock init to cpu_eth_init in cpu/arm926ejs/mx27/generic.c
make MX27 specific phy init conditional on CONFIG_MX27
replace call to imx_get_ahbclk with one to imx_get_fecclk
and define imx_get_fecclk in include/asm-arm/arch-mx27/clock.h
Signed-off-by: John Rigby <jcrigby@gmail.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Fred Fan <fanyefeng@gmail.com> CC: Tom <Tom.Rix@windriver.com>
John Rigby [Tue, 26 Jan 2010 06:12:56 +0000 (23:12 -0700)]
Add support for Freescale MX25 SOC
ARM926EJS core with MX31 peripherals.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de> CC: Fred Fan <fanyefeng@gmail.com> CC: Tom <Tom.Rix@windriver.com>
projects / karo-tx-uboot.git / log