TPIDRURW is a user read/write register forming part of the group of
thread registers in more recent versions of the ARM architecture (~v6+).
Currently, the kernel does not touch this register, which allows tasks
to communicate covertly by reading and writing to the register without
context-switching affecting its contents.
This patch clears TPIDRURW when TPIDRURO is updated via the set_tls
macro, which is called directly from __switch_to. Since the current
behaviour makes the register useless to userspace as far as thread
pointers are concerned, simply clearing the register (rather than saving
and restoring it) will not cause any problems to userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
PL310 errata #588369 and #727915 require writes to the debug registers
of the cache controller to work around known problems. Writing these
registers on L220 may cause deadlock, so ensure that we only perform
this operation when we identify a PL310 at probe time.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The workaround for PL310 erratum #753970 can lead to deadlock on systems
with an L220 cache controller.
This patch makes the workaround effective only when the cache controller
is identified as a PL310 at probe time.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Erratum #326103 ("FSR write bit incorrect on a SWP to read-only memory")
only affects the ARM 1136 core prior to r1p0. The workaround
disassembles the faulting instruction to determine whether it was a read
or write access on all v6 cores.
An issue has been reported on the ARM 11MPCore whereby loading the
faulting instruction may happen in parallel with that page being
unmapped, resulting in a deadlock due to the lack of TLB broadcasting
in hardware:
This patch limits the workaround so that it is only used on affected
cores, which are known to be UP only. Other v6 cores can rely on the
FSR to indicate the access type correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).
We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4abae ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.
But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.
As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9dedd.
With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other. At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation. Ugly, ugly.
However, a prettier solution exists now thanks to the packetized pipe
mode. By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.
This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.
Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Ian Kent <raven@themaw.net> Cc: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.
When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own. The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).
End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time. You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.
NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops. Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.
The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes). But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Ian Kent <raven@themaw.net> Cc: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The field is used to pass the UVC request data length, but can also be
used to signal an error when setting it to a negative value. Switch from
unsigned int to __s32.
pullup() is already called properly by udc-core.c and
there's no need to call it from udc_stop(), in fact that
will cause issues.
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1539) fixes a minor bug in the mass-storage gadget
drivers. When an unknown command is received, the error code sent
back is "Invalid Field in CDB" rather than "Invalid Command". This is
because the bitmask of CDB bytes allowed to be nonzero is incorrect.
When handling an unknown command, we don't care which command bytes
are nonzero. All the bits in the mask should be set, not just eight
of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Steven Rostedt <rostedt@goodmis.org> Tested-by: Andrey Rahmatullin <wrar@wrar.name> Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Signed-off-by: Oliver Neukum <oneukum@suse.de> Tested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to the reporter, external mic starts to work if the
laptop-dmic model is used. According to BIOS pin config, all
pins are consistent with the alc269vb_laptop_dmic fixup, except
for the external mic, which is not present.
BugLink: https://bugs.launchpad.net/bugs/950490 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.
Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On 32-bit systems, a large args->num_cliprects from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 432e58ed ("drm/i915: Avoid
allocation for execbuffer object list").
Signed-off-by: Xi Wang <xi.wang@gmail.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On 32-bit systems, a large args->buffer_count from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 8408c282 ("drm/i915:
First try a normal large kmalloc for the temporary exec buffers").
Signed-off-by: Xi Wang <xi.wang@gmail.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Clearing bit 5 of CACHE_MODE_0 is necessary to prevent GPU hangs in
OpenGL programs such as Google MapsGL, Google Earth, and gzdoom when
using separate stencil buffers. Without it, the GPU tries to use the
LRA eviction policy, which isn't supported. This was supposed to be off
by default, but seems to be on for many machines.
This cannot be done in gen6_init_clock_gating with most of the other
workaround bits; the render ring needs to exist. Otherwise, the
register write gets dropped on the floor (one printk will show it
changed, but a second printk immediately following shows the value
reverts to the old one).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47535 Cc: Rob Castle <futuredub@gmail.com> Cc: Eric Appleman <erappleman@gmail.com> Cc: aaron667@gmx.net Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Kenneth Graunke <kenneth@whitecape.org> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The docs say this is required for Gen7, and since the bit was added for
Gen6, we are also setting it there pit pf paranoia. Particularly as
Chris points out, if PIPE_CONTROL counts as a 3d state packet.
This was found through doc inspection by Ken and applies to Gen6+;
Reported-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
dev_priv keeps track of the current addressing mode that gets set at
execbuffer time. Unfortunately the existing code was doing this before
acquiring struct_mutex which leaves a race with another thread also
doing an execbuffer. If that wasn't bad enough, relocate_slow drops
struct_mutex which opens a much more likely error where another thread
comes in and modifies the state while relocate_slow is being slow.
The solution here is to just defer setting this state until we
absolutely need it, and we know we'll have struct_mutex for the
remainder of our code path.
v2: Keith noticed a bug in the original patch.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We seem to have a decent confusion between the output timings and the
input timings of the sdvo encoder. If I understand the code correctly,
we use the original mode unchanged for the output timings, safe for
the lvds case. And we should use the adjusted mode for input timings.
Clarify the situation by adding an explicit output_dtd to the sdvo
mode_set function and streamline the code-flow by moving the input and
output mode setting in the sdvo encode together.
Furthermore testing showed that the sdvo input timing needs the
unadjusted dotclock, the sdvo chip will automatically compute the
required pixel multiplier to get a dotclock above 100 MHz.
Fix this up when converting a drm mode to an sdvo dtd.
> diff --git a/drivers/gpu/drm/i915/intel_sdvo.c
> b/drivers/gpu/drm/i915/intel_sdvo.c
> index 093e914..62d22ae 100644
> --- a/drivers/gpu/drm/i915/intel_sdvo.c
> +++ b/drivers/gpu/drm/i915/intel_sdvo.c
> @@ -1122,11 +1123,9 @@ static void intel_sdvo_mode_set(struct drm_encoder *encoder,
>
> /* We have tried to get input timing in mode_fixup, and filled into
> adjusted_mode */
> - if (intel_sdvo->is_tv || intel_sdvo->is_lvds) {
> - intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
> + intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
> + if (intel_sdvo->is_tv || intel_sdvo->is_lvds)
> input_dtd.part2.sdvo_flags = intel_sdvo->sdvo_flags;
> - } else
> - intel_sdvo_get_dtd_from_mode(&input_dtd, mode);
>
> /* If it's a TV, we already set the output timing in mode_fixup.
> * Otherwise, the output timing is equal to the input timing.
Due to questions raised in review, below a more elaborate analysis of
the bug at hand:
Sdvo seems to have two timings, one is the output timing which will be
sent over whatever is connected on the other side of the sdvo chip (panel,
hdmi screen, tv), the other is the input timing which will be generated by
the gmch pipe. It looks like sdvo is expected to scale between the two.
To make things slightly more complicated, we have a bunch of special
cases:
- For lvds panel we always use a fixed output timing, namely
intel_sdvo->sdvo_lvds_fixed_mode, hence that special case.
- Sdvo has an interface to generate a preferred input timing for a given
output timing. This is the confusing thing that I've tried to clear up
with the follow-on patches.
- A special requirement is that the input pixel clock needs to be between
100MHz and 200MHz (likely to keep it within the electromechanical design
range of PCIe), 270MHz on later gen4+. Lower pixel clocks are
doubled/quadrupled.
The thing this patch tries to fix is that the pipe needs to be
explicitly instructed to double/quadruple the pixels and needs the
correspondingly higher pixel clock, whereas the sdvo adaptor seems to
do that itself and needs the unadjusted pixel clock. For the sdvo
encode side we already set the pixel mutliplier with a different
command (0x21).
This patch tries to fix this mess by:
- Keeping the output mode timing in the unadjusted plain mode, safe
for the lvds case.
- Storing the input timing in the adjusted_mode with the adjusted
pixel clock. This way we don't need to frob around with the core
crtc mode set code.
- Fixing up the pixelclock when constructing the sdvo dtd timing
struct. This is why the first hunk of the patch is an integral part
of the series.
- Dropping the is_tv special case because input_dtd is equivalent to
adjusted_mode after these changes. Follow-up patches clear this up
further (by simply ripping out intel_sdvo->input_dtd because it's
not needed).
v2: Extend commit message with an in-depth bug analysis.
Reported-and-Tested-by: Bernard Blackham <b-linuxgit@largestprime.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48157 Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Indented the hunk quoted above so quilt doesn't try to apply it] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Noticed by Jerome Glisse (after weeks of debugging).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Newer BKDG[1] versions recommend a different initialization value for
the running average range register in the northbridge. This improves
the power reading by avoiding counter saturations resulting in bogus
values for anything below about 80% of TDP power consumption.
Updated BIOSes will have this new value set up from the beginning,
but meanwhile we correct this value ourselves.
This needs to be done on all northbridges, even on those where the
driver itself does not register at.
This fixes the driver on all current machines to provide proper
values for idle load.
While debugging a latency with someone on IRC (mirage335) on #linux-rt (OFTC),
we discovered that the stacktrace output of the latency tracers
(preemptirqsoff) was empty.
This bug was caused by the creation of the dynamic length stack trace
again (like commit 12b5da3 "tracing: Fix ent_size in trace output" was).
This bug is caused by the latency tracers requiring the next event
to determine the time between the current event and the next. But by
grabbing the next event, the iter->ent_size is set to the next event
instead of the current one. As the stacktrace event is the last event,
this makes the ent_size zero and causes nothing to be printed for
the stack trace. The dynamic stacktrace uses the ent_size to determine
how much of the stack can be printed. The ent_size of zero means
no stack.
The simple fix is to save the iter->ent_size before finding the next event.
Note, mirage335 asked to remain anonymous from LKML and git, so I will
not add the Reported-by and Tested-by tags, even though he did report
the issue and tested the fix.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
With this fix applied build_sched_domains() will return -ENOMEM and
the suspend attempt fails.
Signed-off-by: he, bo <bo.he@intel.com> Reviewed-by: Zhang, Yanmin <yanmin.zhang@intel.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/1335355161.5892.17.camel@hebo
[ So, we fail to deallocate a CPU because we cannot allocate RAM :-/
I don't like that kind of sad behavior but nevertheless it should
not crash under high memory load. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: change filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This loop on EBCISR register was designed to clear IRQ sources before enabling
a DMA channel. This register is clear-on-read so a race condition can appear if
another channel is already active and has just finished its transfer.
Removing this read on EBCISR is fixing the issue as there is no case where an IRQ
could be pending: we already make sure that this register is drained at probe()
time and during resume.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Line widgets had not been included in either the power up or power down
sequences so if a widget had an event associated with it that event would
never be run. Fix this minimally by adding them to the sequences, we
should probably be doing away with the specific widget types as they all
have the same priority anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we boot on a machine that can hotplug CPUs and we
are using 'dom0_max_vcpus=X' on the Xen hypervisor line
to clip the amount of CPUs available to the initial domain,
we get this:
(XEN) Command line: com1=115200,8n1 dom0_mem=8G noreboot dom0_max_vcpus=8 sync_console mce_verbosity=verbose console=com1,vga loglvl=all guest_loglvl=all
.. snip..
DMI: Intel Corporation S2600CP/S2600CP, BIOS SE5C600.86B.99.99.x032.072520111118 07/25/2011
.. snip.
SMP: Allowing 64 CPUs, 32 hotplug CPUs
installing Xen timer for CPU 7
cpu 7 spinlock event irq 361
NMI watchdog: disabled (cpu7): hardware events not enabled
Brought up 8 CPUs
.. snip..
[acpi processor finds the CPUs are not initialized and starts calling
arch_register_cpu, which creates /sys/devices/system/cpu/cpu8/online]
CPU 8 got hotplugged
CPU 9 got hotplugged
CPU 10 got hotplugged
.. snip..
initcall 1_acpi_battery_init_async+0x0/0x1b returned 0 after 406 usecs
calling erst_init+0x0/0x2bb @ 1
[and the scheduler sticks newly started tasks on the new CPUs, but
said CPUs cannot be initialized b/c the hypervisor has limited the
amount of vCPUS to 8 - as per the dom0_max_vcpus=8 flag.
The spinlock tries to kick the other CPU, but the structure for that
is not initialized and we crash.]
BUG: unable to handle kernel paging request at fffffffffffffed8
IP: [<ffffffff81035289>] xen_spin_lock+0x29/0x60
PGD 180d067 PUD 180e067 PMD 0
Oops: 0002 [#1] SMP
CPU 7
Modules linked in:
In xen_restore_fl_direct(), xen_force_evtchn_callback() was being
called even if no events were pending. This resulted in (depending on
workload) about a 100 times as many xen_version hypercalls as
necessary.
Fix this by correcting the sense of the conditional jump.
This seems to give a significant performance benefit for some
workloads.
There is some subtle tricksy "..since the check here is trying to
check both pending and masked in a single cmpw, but I think this is
correct. It will call check_events now only when the combined
mask+pending word is 0x0001 (aka unmasked, pending)." (Ian)
Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While that commit was technically the right thing to do, and made the
x86-64 compat mode work identically to native 32-bit mode (and thus
fixing the problem with a 32-bit systemd install on a 64-bit kernel), it
turns out that the automount binaries had workarounds for this compat
problem.
Now, the workarounds are disgusting: doing an "uname()" to find out the
architecture of the kernel, and then comparing it for the 64-bit cases
and fixing up the size of the read() in automount for those. And they
were confused: it's not actually a generic 64-bit issue at all, it's
very much tied to just x86-64, which has different alignment for an
'u64' in 64-bit mode than in 32-bit mode.
But the end result is that fixing the compat layer actually breaks the
case of a 32-bit automount on a x86-64 kernel.
There are various approaches to fix this (including just doing a
"strcmp()" on current->comm and comparing it to "automount"), but I
think that I will do the one that teaches pipes about a special "packet
mode", which will allow user space to not have to care too deeply about
the padding at the end of the autofs packet.
That change will make the compat workaround unnecessary, so let's revert
it first, and get automount working again in compat mode. The
packetized pipes will then fix autofs for systemd.
Reported-and-requested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Current APIC code assumes MSR_IA32_APICBASE is present for all systems.
Pentium Classic P5 and friends didn't have this MSR. MSR_IA32_APICBASE
was introduced as an architectural MSR by Intel @ P6.
Code paths that can touch this MSR invalidly are when vendor == Intel &&
cpu-family == 5 and APIC bit is set in CPUID - or when you simply pass
lapic on the kernel command line, on a P5.
The below patch stops Linux incorrectly interfering with the
MSR_IA32_APICBASE for P5 class machines. Other code paths exist that
touch the MSR - however those paths are not currently reachable for a
conformant P5.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linux.intel.com> Link: http://lkml.kernel.org/r/4F8EEDD3.1080404@linux.intel.com Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This is due to commit 8a25a2fd126c ("cpu: convert 'cpu' and
'machinecheck' sysdev_class to a regular subsystem") which renders
commit 6c53cbfced04 ("x86, microcode: Correct sysdev_add error path")
useless.
When hostname contains colon (e.g. when it is an IPv6 address) it needs
to be enclosed in brackets to make parsing of NFS device string possible.
Fix nfs_do_root_mount() to enclose hostname properly when needed. NFS code
actually does not need this as it does not parse the string passed by
nfs_do_root_mount() but the device string is exposed to userspace in
/proc/mounts.
CC: Josh Boyer <jwboyer@redhat.com> CC: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While reviewing the sysctl code in ax25 I spotted races in ax25_exit
where it is possible to receive notifications and packets after already
freeing up some of the data structures needed to process those
notifications and updates.
Call unregister_netdevice_notifier early so that the rest of the cleanup
code does not need to deal with network devices. This takes advantage
of my recent enhancement to unregister_netdevice_notifier to send
unregister notifications of all network devices that are current
registered.
Move the unregistration for packet types, socket types and protocol
types before we cleanup any of the ax25 data structures to remove the
possibilities of other races.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array. I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.
tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.
This patch fixes one of the performance issue we noticed with GRO on.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).
However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:
This fixes gred_dump() in WRED mode to use the values held in wred_set.
Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com> Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
After investigation, it turns out TCP uses sk_stream_alloc_skb() and
used as a convention skb_tailroom(skb) to know how many bytes of data
payload could be put in this skb (for non SG capable devices)
Note : these skb used kmalloc-4096 (MTU=1500 + MAX_HEADER +
sizeof(struct skb_shared_info) being above 2048)
Later, mac80211 layer need to add some bytes at the tail of skb
(IEEE80211_ENCRYPT_TAILROOM = 18 bytes) and since no more tailroom is
available has to call pskb_expand_head() and request order-1
allocations.
This patch changes sk_stream_alloc_skb() so that only
sk->sk_prot->max_header bytes of headroom are reserved, and use a new
skb field, avail_size to hold the data payload limit.
This way, order-0 allocations done by TCP stack can leave more than 2 KB
of tailroom and no more allocation is performed in mac80211 layer (or
any layer needing some tailroom)
avail_size is unioned with mark/dropcount, since mark will be set later
in IP stack for output packets. Therefore, skb size is unchanged.
Reported-by: Marc MERLIN <marc@merlins.org> Tested-by: Marc MERLIN <marc@merlins.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Correct commit hash for follow-on bug fix] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f07d960df3 (tcp: avoid frag allocation for small frames)
breaked assumption in tcp stack that skb is either linear (skb->data_len
== 0), or fully fragged (skb->data_len == skb->len)
tcp_trim_head() made this assumption, we must fix it.
Thanks to Vijay for providing a very detailed explanation.
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
Turns out part of the problem comes from pskb_expand_head() not using
ksize() to get exact head size given by kmalloc(). Doing the same thing
than __alloc_skb() allows more tailroom in skb and can prevent future
reallocations.
As a bonus, struct skb_shared_info becomes cache line aligned.
Reported-by: Marc MERLIN <marc@merlins.org> Tested-by: Marc MERLIN <marc@merlins.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A phonet packet is limited to USHRT_MAX bytes, this is never checked during
tx which means that the user can specify any size he wishes, and the kernel
will attempt to allocate that size.
In the good case, it'll lead to the following warning, but it may also cause
the kernel to kick in the OOM and kill a random task on the server.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Convert array index from the loop bound to the loop index.
And remove the void type conversion to ip6_mc_del1_src() return
code, seem it is unnecessary, since ip6_mc_del1_src() does not
use __must_check similar attribute, no compiler will report the
warning when it is removed.
v2: enrich the commit header
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable. First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.
In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.
So this patch simply removes all code associated with group
queries in response to group leave messages.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct
sctp_event_subscribe.
Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.
This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.
This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.
This leads to the new behavior that users see what they have been aware
of at compile time.
The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)
The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.
4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)
This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)
In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.
Call tcp_push() only if MSG_MORE is not set in the flags parameter.
This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.
In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: Tom Herbert <therbert@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: H.K. Jerry Chu <hkchu@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Mahesh Bandewar <maheshb@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Allow a v3 unchecked open of a non-regular file succeed as if it were a
lookup; typically a client in such a case will want to fall back on a
local open, so succeeding and giving it the filehandle is more useful
than failing with nfserr_exist, which makes it appear that nothing at
all exists by that name.
Similarly for v4, on an open-create, return the same errors we would on
an attempt to open a non-regular file, instead of returning
nfserr_exist.
This fixes a problem found doing a v4 open of a symlink with
O_RDONLY|O_CREAT, which resulted in the current client returning EEXIST.
Thanks also to Trond for analysis.
Reported-by: Orion Poplawski <orion@cora.nwra.com> Tested-by: Orion Poplawski <orion@cora.nwra.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[bwh: Backported to 3.2: use &resfh, not resfh] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit f04565ddf52 (dev: use name hash for dev_seq_ops) added a second
regression, as some devices are missing from /proc/net/dev if many
devices are defined.
When seq_file buffer is filled, the last ->next/show() method is
canceled (pos value is reverted to value prior ->next() call)
Problem is after above commit, we dont restart the lookup at right
position in ->start() method.
Fix this by removing the internal 'pos' pointer added in commit, since
we need to use the 'loff_t *pos' provided by seq_file layer.
This also reverts commit 5cac98dd0 (net: Fix corruption
in /proc/*/net/dev_mcast), since its not needed anymore.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Mihai Maruseac <mmaruseac@ixiacom.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
->root_flags is __le64 and all accesses to it go through the helpers
that do proper conversions. Except for btrfs_root_readonly(), which
checks bit 0 as in host-endian...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Restore the original logics ("fail on mountpoints, negatives and in
case of fh_compose() failures"). Since commit 8177e (nfsd: clean up
readdirplus encoding) that got broken -
rv = fh_compose(fhp, exp, dchild, &cd->fh);
if (rv)
goto out;
if (!dchild->d_inode)
goto out;
rv = 0;
out:
is equivalent to
rv = fh_compose(fhp, exp, dchild, &cd->fh);
out:
and the second check has no effect whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
->ts_id_status gets nfs errno, i.e. it's already big-endian; no need
to apply htonl() to it. Broken by commit 174568 (NFSD: Added TEST_STATEID
operation) last year...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: "J. Bruce Fields" <bfields@fieldses.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
nfsd_open() already returns an NFS error value; only vfs_test_lock()
result needs to be fed through nfserrno(). Broken by commit 55ef12
(nfsd: Ensure nfsv4 calls the underlying filesystem on LOCKT)
three years ago...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
..._want_write() returns -EROFS on failure, _not_ an NFS error value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context for previously cherry-picked
commit d42a179b941a9e4cc6cf41d0f3cbadd75fc48a89 'rt2x00: Add support
for D-Link DWA-127 to rt2800usb'] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed device initialization to be children of the
bus master, not children of the bus masters parent device. The pdata
pointer used in fsl_spi_chipselect must updated to reflect the changed
initialization.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Device are added as children of the bus master's parent device, but
spi_unregister_master() looks for devices to unregister in the bus
master's children. This results in the child devices not being
unregistered.
Fix this by registering devices as direct children of the bus master.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 28d82dc1c4ed ("epoll: limit paths") that I did to limit the
number of possible wakeup paths in epoll is causing a few applications
to longer work (dovecot for one).
The original patch is really about limiting the amount of epoll nesting
(since epoll fds can be attached to other fds). Thus, we probably can
allow an unlimited number of paths of depth 1. My current patch limits
it at 1000. And enforce the limits on paths that have a greater depth.
This is captured in: https://bugzilla.redhat.com/show_bug.cgi?id=681578
Signed-off-by: Jason Baron <jbaron@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Touchpad LED will not turn on after S3, it will make the touchpad status
doesn't consist with the LED.
By adding one flag to let the LED device restore it's status.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add "Vostro 3555", "Inspiron N311z", and "Inspiron M5110" into quirks,
so that they could have touchpad LED function work.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We've been adding new mappings, but not destroying old mappings.
This can lead to a page leak as pages are pinned using
get_user_pages, but only unpinned with put_page if they still
exist in the memslots list on vm shutdown. A memslot that is
destroyed while an iommu domain is enabled for the guest will
therefore result in an elevated page reference count that is
never cleared.
Additionally, without this fix, the iommu is only programmed
with the first translation for a gpa. This can result in
peer-to-peer errors if a mapping is destroyed and replaced by a
new mapping at the same gpa as the iommu will still be pointing
to the original, pinned memory address.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.
These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.
Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.
Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
Probably the IRQ ends up somewhere unnoticed.
According to reports on the net, the Intel DH61WW board is also affected.
Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Tested-by: Charlie Suffin <charlie.suffin@stratus.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.
Cc: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pm_runtime_enable is being called after omap2430_musb_init. Hence
pm_runtime_get_sync in omap2430_musb_init does not have any effect (does
not enable clocks) resulting in a crash during register access. It is
fixed here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes a bug which causes NULL pointer dereference in
ffs_ep0_ioctl. The bug happens when the FunctionFS is not bound (either
has not been bound yet or has been bound and then unbound) and can be
reproduced with running the following commands:
int main(void)
{
int fd = open("/dev/usbgadget/ep0", O_RDWR);
ioctl(fd, FUNCTIONFS_CLEAR_HALT);
return 0;
}
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1548) fixes a recently-introduced incompatibility
between the UDC core and the dummy-hcd driver. Commit 8ae8090c82eb407267001f75b3d256b3bd4ae691 (usb: gadget: udc-core: fix
asymmetric calls in remove_driver) moved the usb_gadget_udc_stop()
call in usb_gadget_remove_driver() below the usb_gadget_disconnect()
call.
As a result, usb_gadget_disconnect() gets called at a time when the
gadget driver believes it has been unbound but dummy-hcd believes
it has not. A nasty error ensues when dummy-hcd calls the gadget
driver's disconnect method a second time.
To fix the problem, this patch moves the gadget driver's unbind
notification after the usb_gadget_disconnect() call. Now nothing
happens between the two unbind notifications, so nothing goes wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6d258a4 (usb: gadget: udc-core: stop UDC on device-initiated
disconnect) introduced another case of asymmetric calls when issuing
a device-initiated disconnect. Fix it.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
During modprobe of gadget driver, pullup is called after
udc_start. In order to make the exit path symmetric when
removing a gadget driver, call pullup before ->udc_stop.
This is needed to avoid issues with PM where udc_stop
disables the module completely (put IP in reset state,
cut functional and interface clocks, and so on), which
prevents us from accessing the IP's address space,
thus creating the possibility of an abort exception
when we try to access IP's address space after clocks
are off.
Signed-off-by: Partha Basak <p-basak2@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we want to do device-initiated disconnect,
let's make sure we stop the UDC in order to
e.g. allow lower power states to be achieved by
turning off unnecessary clocks and/or stoping
PHYs.
When reconnecting, call ->udc_start() again to
make sure UDC is reinitialized.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit fccf4e86200b8f5edd9a65da26f150e32ba79808 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub. A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.
Right now the driver tests whether the root hub is running, and that
is not the correct test. In particular, if the controller has died
then the root hub should not be restarted. In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.
In the end, the test needs to be changed. Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended. This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Peter Chen <B29397@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
These devices have a number of non serial interfaces as well. Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.
We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
projects / karo-tx-linux.git / log