Tejun Heo [Tue, 11 Jun 2013 07:11:36 +0000 (00:11 -0700)]
libata: skip SRST for all SIMG [34]7x port-multipliers
For some reason, a lot of port-multipliers have issues with softreset.
SIMG [34]7x series port-multipliers have been quite erratic in this
regard. I recall that it was better with some firmware revisions and
the current list of quirks worked fine for a while. I think it got
worse with later firmwares or maybe my test coverage wasn't good
enough. Anyways, HPA is reporting that his 3726 setup suffers SRST
failures and then the PMP gets confused and fails to probe the last
port.
The hope was that we try to stick to the standard as much as possible
and soonish the PMPs and their firmwares will improve in quality, so
the quirk list was kept to minimum. Well, it seems like that's never
gonna happen.
Let's set NO_SRST for all [34]7x PMPs so that whatever remaining
userbase of the device suffer the least. Maybe we should do the same
for 57xx's but unfortunately I don't have any device left to test and
I'm not even sure 57xx's have ever been made widely available, so
let's leave those alone for now.
Shane Huang [Sat, 8 Jun 2013 08:00:16 +0000 (16:00 +0800)]
ahci: remove pmp link online check in FBS EH
ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2
Mark Langsdorf [Thu, 30 May 2013 20:17:30 +0000 (15:17 -0500)]
ahci: make ahci_transmit_led_message into a function pointer
Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Sergei Shtylyov [Mon, 3 Jun 2013 20:16:05 +0000 (13:16 -0700)]
sata_rcar: fix compilation warning in sata_rcar_thaw()
When compiling the driver with gcc 4.8, it gives the following warning:
drivers/ata/sata_rcar.c: In function `sata_rcar_thaw':
drivers/ata/sata_rcar.c:183:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Fix the warning by explicit cast of the 'unsigned long' value to 'u32'.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Mark Langsdorf [Mon, 3 Jun 2013 13:22:54 +0000 (08:22 -0500)]
sata_highbank: increase retry count but shorten duration for Calxeda controller
Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
Jingoo Han [Mon, 3 Jun 2013 05:05:36 +0000 (14:05 +0900)]
ata: use pci_get_drvdata()
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev. This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Sergei Shtylyov [Tue, 21 May 2013 19:24:22 +0000 (23:24 +0400)]
ipr: qc_fill_rtf() method should not store alternate status register
The 'ctl' field of the 'struct ata_taskfile' is not really dual purpose, i.e.
it is not intended for storing the alternate status register (which is mapped
at the same address in the legacy IDE controllers) in the qc_fill_rtf() method.
No other 'libata' driver except 'drivers/scsi/ipr.c' stores the alternate status
register's value in the 'ctl' field of 'qc->result_tf', hence this driver should
not do this as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Sergei Shtylyov [Fri, 31 May 2013 22:38:35 +0000 (02:38 +0400)]
sata_rcar: fix interrupt handling
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.
Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear only those interrupts that we have read
as active first time around, because else we have a race and risk clearing an
interrupt that can occur between read and write of the SATAINTSTAT register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
Sergei Shtylyov [Mon, 27 May 2013 22:46:41 +0000 (02:46 +0400)]
sata_rcar: add 'base' local variable to some functions
The 'base' field of 'struct sata_rcar_priv' is used very often
throughout the driver, so it seems worth loading it into a local
variable if it's used more than once in a function.
While at it, put some unitialized variables after intialized ones for
aesthetic reasons. :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Sergei Shtylyov [Mon, 27 May 2013 22:45:08 +0000 (02:45 +0400)]
sata_rcar: correct 'sata_rcar_sht'
Using ATA_BMDMA_SHT() to intialize 'sata_rcar_sht' was suboptimal as
the R-Car descriptor table transfer counter is 28 bits wide (bit 1 to
bit 28), so that the 'dma_boundary' field of 0xFFFF is just too small,
as well as the 'sg_tablesize' field of 128. Use ATA_BASE_SHT() to
initialize 'sata_rcar_sht' instead and give proper values to the
'dma_boundary' and 'sg_tablesize' fields explicitly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Sergei Shtylyov [Mon, 27 May 2013 22:43:23 +0000 (02:43 +0400)]
sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
I've modified sata_rcar_bmdma_fill_sg() to take care of splitting long
scatter/ gather segments due to the descriptor table transfer counter
being only 28 bits wide (bit 1 to bit 28) but that was in vain as even
if 'sata_rcar_sht' specified a correct 'dma_boundary' field, the DMA
and block layers would have split the S/G segments on the necassary
boundaries. Since the driver uses ATA_BMDMA_SHT() to initilaize
'sata_rcar_sht', the boundary is much smaller, only 0xFFFF, so the
code I've added is even more useless, and it's better to just remove
it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Simon Horman [Fri, 24 May 2013 02:05:59 +0000 (11:05 +0900)]
libata: do not limit R-Car SATA driver to shmobile
The motivation for this is to allow the driver to be
used with the r8a7790 SoC.
I believe that rather than adding another SoC to the list of allowed SoCs
it is better to simply remove the dependency of the driver on shmobile all
together.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Tejun Heo <tj@kernel.org>
Jingoo Han [Thu, 23 May 2013 10:41:21 +0000 (19:41 +0900)]
ata: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
AHCI: Make distinct names for ports in /proc/interrupts
Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.
Reported-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Sergei Shtylyov [Tue, 21 May 2013 19:07:54 +0000 (23:07 +0400)]
sata_rcar: clear STOP bit in bmdma_start() method
Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started. Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org>
libata honors DMADIR for regular commands, but not for internal commands
used (among other) during device initialisation.
This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611
(such as "Abit Serillel 2") end up disabled when used with an ATAPI device
after a few tries.
Log output of the bridge being hot-plugged with an ATAPI drive:
[ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen
[ 9631.212913] ata1: irq_stat 0x00000040, connection status changed
[ 9631.212923] ata1: SError: { CommWake 10B8B DevExch }
[ 9631.212939] ata1: hard resetting link
[ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33
[ 9632.106407] ata1.00: applying bridge limits
[ 9632.108151] ata1.00: configured for UDMA/33
[ 9637.105303] ata1.00: qc timeout (cmd 0xa0)
[ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9637.105335] ata1: hard resetting link
[ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9638.047878] ata1.00: configured for UDMA/33
[ 9643.044933] ata1.00: qc timeout (cmd 0xa0)
[ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps
[ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3
[ 9643.044979] ata1: hard resetting link
[ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9643.987471] ata1.00: configured for UDMA/33
[ 9648.984591] ata1.00: qc timeout (cmd 0xa0)
[ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5)
[ 9648.984619] ata1.00: disabled
[ 9649.000593] ata1: hard resetting link
[ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 9649.955864] ata1: EH complete
With this patch, the drive enumerates correctly when libata is loaded with
atapi_dmadir=1:
David Milburn [Tue, 14 May 2013 18:48:40 +0000 (13:48 -0500)]
libata: export ata_port port_no attribute via /sys
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.
/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root 0 Mar 6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar 6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar 6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar 6 12:43 port_no
drwxr-xr-x. 2 root root 0 Mar 6 12:42 power
lrwxrwxrwx. 1 root root 0 Mar 6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar 6 12:40 uevent
1
Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Linus Torvalds [Sun, 12 May 2013 00:04:59 +0000 (17:04 -0700)]
Merge tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing/kprobes update from Steven Rostedt:
"The majority of these changes are from Masami Hiramatsu bringing
kprobes up to par with the latest changes to ftrace (multi buffering
and the new function probes).
He also discovered and fixed some bugs in doing so. When pulling in
his patches, I also found a few minor bugs as well and fixed them.
This also includes a compile fix for some archs that select the ring
buffer but not tracing.
I based this off of the last patch you took from me that fixed the
merge conflict error, as that was the commit that had all the changes
I needed for this set of changes."
* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Support soft-mode disabling
tracing/kprobes: Support ftrace_event_file base multibuffer
tracing/kprobes: Pass trace_probe directly from dispatcher
tracing/kprobes: Increment probe hit-count even if it is used by perf
tracing/kprobes: Use bool for retprobe checker
ftrace: Fix function probe when more than one probe is added
ftrace: Fix the output of enabled_functions debug file
ftrace: Fix locking in register_ftrace_function_probe()
tracing: Add helper function trace_create_new_event() to remove duplicate code
tracing: Modify soft-mode only if there's no other referrer
tracing: Indicate enabled soft-mode in enable file
tracing/kprobes: Fix to increment return event probe hit-count
ftrace: Cleanup regex_lock and ftrace_lock around hash updating
ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
ftrace: Have ftrace_regex_write() return either read or error
tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
tracing: Don't succeed if event_enable_func did not register anything
ring-buffer: Select IRQ_WORK
Linus Torvalds [Sat, 11 May 2013 23:19:30 +0000 (16:19 -0700)]
Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- More fixes in the vCPU PVHVM hotplug path.
- Add more documentation.
- Fix various ARM related issues in the Xen generic drivers.
- Updates in the xen-pciback driver per Bjorn's updates.
- Mask the x2APIC feature for PV guests.
* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Used cached MSI-X capability offset
xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
xen: mask x2APIC feature in PV
xen: SWIOTLB is only used on x86
xen/spinlock: Fix check from greater than to be also be greater or equal to.
xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
xen/vcpu: Document the xen_vcpu_info and xen_vcpu
xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.
Linus Torvalds [Sat, 11 May 2013 22:24:22 +0000 (15:24 -0700)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second SCSI update from James "Jaj B" Bottomley:
"This is the final round of SCSI patches for the merge window. It
consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
be2iscsi, pm80xx, qla4x and ipr).
There's also the power management updates that complete the patches in
Jens' tree, an iscsi refcounting problem fix from the last pull, some
dif handling in scsi_debug fixes, a few nice code cleanups and an
error handling busy bug fix."
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
[SCSI] sd: change to auto suspend mode
[SCSI] sd: use REQ_PM in sd's runtime suspend operation
[SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
[SCSI] ufs: Correct the expected data transfersize
...
Linus Torvalds [Sat, 11 May 2013 21:29:11 +0000 (14:29 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Linus Torvalds [Fri, 10 May 2013 16:27:40 +0000 (09:27 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform drivers from Matthew Garrett:
"Small set of updates, mainly trivial bugfixes and some small updates
to deal with newer hardware.
There's also a new driver that allows qemu guests to notify the
hypervisor that they've just paniced, which seems useful."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Add support for fan button on Ideapad Z580
pvpanic: pvpanic device driver
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. X75A
drivers: platform: x86: Use PTR_RET function
sony-laptop: SVS151290S kbd backlight and gfx switch support
hp-wmi: add more definitions for new event_id's
dell-laptop: Fix krealloc() misuse in parse_da_table()
hp_accel: Ignore the error from lis3lv02d_poweron() at resume
dell: add new dell WMI format for the AIO machines
Linus Torvalds [Fri, 10 May 2013 16:21:05 +0000 (09:21 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
Linus Torvalds [Fri, 10 May 2013 16:20:01 +0000 (09:20 -0700)]
Merge tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs update from Tyler Hicks:
"Improve performance when AES-NI (and most likely other crypto
accelerators) is available by moving to the ablkcipher crypto API.
The improvement is more apparent on faster storage devices.
There's no noticeable change when hardware crypto is not available"
* tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Use the ablkcipher crypto API
Linus Torvalds [Fri, 10 May 2013 16:09:47 +0000 (09:09 -0700)]
Merge tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6
Pull misc fixes from David Woodhouse:
"This is some miscellaneous cleanups that don't really belong anywhere
else (or were ignored), that have been sitting in linux-next for some
time. Two of them are fixes resulting from my audit of krealloc()
usage that don't seem to have elicited any response when I posted
them, and the other three are patches from Artem removing dead code."
* tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6:
pcmcia: remove RPX board stuff
m68k: remove rpxlite stuff
pcmcia: remove Motorola MBX860 support
params: Fix potential memory leak in add_sysfs_param()
dell-laptop: Fix krealloc() misuse in parse_da_table()
Linus Torvalds [Fri, 10 May 2013 16:08:21 +0000 (09:08 -0700)]
Merge tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Gleb Natapov:
"Most of the fixes are in the emulator since now we emulate more than
we did before for correctness sake we see more bugs there, but there
is also an OOPS fixed and corruption of xcr0 register."
* tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: emulator: emulate SALC
KVM: emulator: emulate XLAT
KVM: emulator: emulate AAM
KVM: VMX: fix halt emulation while emulating invalid guest sate
KVM: Fix kvm_irqfd_init initialization
KVM: x86: fix maintenance of guest/host xcr0 state
Linus Torvalds [Fri, 10 May 2013 16:02:50 +0000 (09:02 -0700)]
Merge tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair Kergon:
"Allow devices that hold metadata for the device-mapper thin
provisioning target to be extended easily; allow WRITE SAME on
multipath devices; an assortment of little fixes and clean-ups."
* tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (21 commits)
dm cache: set config value
dm cache: move config fns
dm thin: generate event when metadata threshold passed
dm persistent metadata: add space map threshold callback
dm persistent data: add threshold callback to space map
dm thin: detect metadata device resizing
dm persistent data: support space map resizing
dm thin: open dev read only when possible
dm thin: refactor data dev resize
dm cache: replace memcpy with struct assignment
dm cache: fix typos in comments
dm cache policy: fix description of lookup fn
dm: document iterate_devices
dm persistent data: fix error message typos
dm cache: tune migration throttling
dm mpath: enable WRITE SAME support
dm table: fix write same support
dm bufio: avoid a possible __vmalloc deadlock
dm snapshot: fix error return code in snapshot_ctr
dm cache: fix error return code in cache_create
...
Linus Torvalds [Fri, 10 May 2013 16:00:39 +0000 (09:00 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix usage of sleeping lock in atomic context from Jiri Kosina
- build fix for hid-steelseries under certain .config setups by Simon Wood
- simple mismerge fix from Fernando Luis Vázquez Cao
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: debug: fix RCU preemption issue
HID: hid-steelseries fix led class build issue
HID: reintroduce fix-up for certain Sony RF receivers
Linus Torvalds [Fri, 10 May 2013 14:51:56 +0000 (07:51 -0700)]
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains small fixes since the previous pull request:
- A few regression fixes and small updates of HD-audio
- Yet another fix for Haswell HDMI audio
- A copule of trivial fixes in ASoC McASP, DPAM and WM8994"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: hda - Don't set up active streams twice"
ALSA: Add comment for control TLV API
ALSA: hda - Apply pin-enablement workaround to all Haswell HDMI codecs
ALSA: HDA: Fix Oops caused by dereference NULL pointer
ALSA: mips/sgio2audio: Remove redundant platform_set_drvdata()
ALSA: mips/hal2: Remove redundant platform_set_drvdata()
ALSA: hda - Fix 3.9 regression of EAPD init on Conexant codecs
sound: Fix make allmodconfig on MIPS
ALSA: hda - Fix system panic when DMA > 40 bits for Nvidia audio controllers
ALSA: atmel: Remove redundant platform_set_drvdata()
ASoC: McASP: Fix receive clock polarity in DAIFMT_NB_NF mode.
ASoC: wm8994: missing break in wm8994_aif3_hw_params()
ASoC: McASP: Add pins output direction for rx clocks when configured in CBS_CFS format
ASoC: dapm: use clk_prepare_enable and clk_disable_unprepare
Linus Torvalds [Fri, 10 May 2013 14:48:05 +0000 (07:48 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
- More work on DT support for various platforms
- Various fixes that were to late to make it straight into 3.9
- Improved platform support, in particular the Netlogic XLR and
BCM63xx, and the SEAD3 and Malta eval boards.
- Support for several Ralink SOC families.
- Complete support for the microMIPS ASE which basically reencodes the
existing MIPS32/MIPS64 ISA to use non-constant size instructions.
- Some fallout from LTO work which remove old cruft and will generally
make the MIPS kernel easier to maintain and resistant to compiler
optimization, even in absence of LTO.
- KVM support. While MIPS has announced hardware virtualization
extensions this KVM extension uses trap and emulate mode for
virtualization of MIPS32. More KVM work to add support for VZ
hardware virtualizaiton extensions and MIPS64 will probably already
be merged for 3.11.
Most of this has been sitting in -next for a long time. All defconfigs
have been build or run time tested except three for which fixes are being
sent by other maintainers.
Semantic conflict with kvm updates done as per Ralf
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (118 commits)
MIPS: Add new GIC clockevent driver.
MIPS: Formatting clean-ups for clocksources.
MIPS: Refactor GIC clocksource code.
MIPS: Move 'gic_frequency' to common location.
MIPS: Move 'gic_present' to common location.
MIPS: MIPS16e: Add unaligned access support.
MIPS: MIPS16e: Support handling of delay slots.
MIPS: MIPS16e: Add instruction formats.
MIPS: microMIPS: Optimise 'strnlen' core library function.
MIPS: microMIPS: Optimise 'strlen' core library function.
MIPS: microMIPS: Optimise 'strncpy' core library function.
MIPS: microMIPS: Optimise 'memset' core library function.
MIPS: microMIPS: Add configuration option for microMIPS kernel.
MIPS: microMIPS: Disable LL/SC and fix linker bug.
MIPS: microMIPS: Add vdso support.
MIPS: microMIPS: Add unaligned access support.
MIPS: microMIPS: Support handling of delay slots.
MIPS: microMIPS: Add support for exception handling.
MIPS: microMIPS: Floating point support.
MIPS: microMIPS: Fix macro naming in micro-assembler.
...
Mike Christie [Mon, 6 May 2013 17:06:56 +0000 (12:06 -0500)]
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: Zhao Hongjiang <zhaohongjiang@huawei.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Bottomley [Tue, 7 May 2013 21:44:06 +0000 (14:44 -0700)]
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:38:40 +0000 (18:08 +0530)]
[SCSI] pm80xx: thermal, sas controller config and error handling update
Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants
[jejb: fix up tabs and spaces issues] Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:38:08 +0000 (18:08 +0530)]
[SCSI] pm80xx: NCQ error handling changes
Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.
[jejb: fix checkpatch issues] Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:37:35 +0000 (18:07 +0530)]
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:37:09 +0000 (18:07 +0530)]
[SCSI] pm80xx: Changed module name and debug messages update
Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:36:40 +0000 (18:06 +0530)]
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:35:55 +0000 (18:05 +0530)]
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Wed, 17 Apr 2013 11:07:02 +0000 (16:37 +0530)]
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Tue, 19 Mar 2013 12:26:17 +0000 (17:56 +0530)]
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Wed, 27 Feb 2013 14:57:43 +0000 (20:27 +0530)]
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sakthivel K [Wed, 17 Apr 2013 10:56:36 +0000 (16:26 +0530)]
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com> Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com> Acked-by: Jack Wang <jack_wang@usish.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Thu, 25 Apr 2013 06:10:00 +0000 (08:10 +0200)]
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
scsi_send_eh_cmnd() is calling queuecommand() directly, so
it needs to check the return value here.
The only valid return codes for queuecommand() are 'busy'
states, so we need to wait for a bit to allow the LLDD
to recover.
Based on an earlier patch from Wen Xiong.
[jejb: fix confusion between msec and jiffies values and other issues]
[bvanassche: correct stall_for interval] Cc: Wen Xiong <wenxiong@linux.vnet.ibm.com> Cc: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Fri, 10 May 2013 14:22:35 +0000 (07:22 -0700)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"The bulk of the changes are generalizing the ColdFire v3 core support
and adding in 537x CPU support. Also a couple of other bug fixes, one
to fix a reintroduction of a past bug in the romfs filesystem nommu
support."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable Timer on coldfire 532x
m68knommu: fix ColdFire 5373/5329 QSPI base address
m68knommu: add support for configuring a Freescale M5373EVB board
m68knommu: add support for the ColdFire 537x family of CPUs
m68knommu: make ColdFire M532x platform support more v3 generic
m68knommu: create and use a common M53xx ColdFire class of CPUs
m68k: remove unused asm/dbg.h
m68k: Set ColdFire ACR1 cache mode depending on kernel configuration
romfs: fix nommu map length to keep inside filesystem
m68k: clean up unused "config ROMVECSIZE"
Linus Torvalds [Fri, 10 May 2013 14:21:16 +0000 (07:21 -0700)]
Merge tag 'for-linus' of git://github.com/realmz/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'for-linus' of git://github.com/realmz/blackfin-linux:
bfin cache: dcplb map: add 16M dcplb map for BF60x
blackfin: smp: fix smp build after drop asm/system.h
blackfin: fix bootup core clock and system clock display
Platform Nand: Set the GPIO for NAND read as input
blackfin: rename vmImage to uImage after we move to buildroot
blackfin: twi: Remove bogus #endif
bf609: rsi: Add bf609 rsi MMR macro and board platform data.
blackfin: dmc: Improve DDR2 write through in DMC effict controller.
Linus Torvalds [Fri, 10 May 2013 14:19:52 +0000 (07:19 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze updates from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Enable IRQ in arch_cpu_idle
microblaze: Fix uaccess_ok macro
microblaze: Add support for new cpu versions and target architecture
microblaze: Do not select OPT_LIB_ASM by default
microblaze: Fix initrd support
microblaze: Do not use r6 in head.S
microblaze: pci: Remove duplicated header
microblaze: Set the default irq_domain
microblaze: pci: Remove duplicated include from pci-common.c
Joe Thornber [Fri, 10 May 2013 13:37:20 +0000 (14:37 +0100)]
dm persistent data: add threshold callback to space map
Add a threshold callback function to the persistent data space map
interface for a subsequent patch to use.
dm-thin and dm-cache are interested in knowing when they're getting
low on metadata or data blocks. This patch introduces a new method
for registering a callback against a threshold.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Joe Thornber [Fri, 10 May 2013 13:37:19 +0000 (14:37 +0100)]
dm persistent data: support space map resizing
Support extending a dm persistent data metadata space map.
The extend itself is implemented by switching back to the boostrap
allocator and pointing to the new space. The extra bitmap indexes are
then allocated from the new space, and finally we switch back to the
proper space map ops and tweak the reference counts.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Joe Thornber [Fri, 10 May 2013 13:37:19 +0000 (14:37 +0100)]
dm thin: open dev read only when possible
If a thin pool is created in read-only-metadata mode then only open the
metadata device read-only.
Previously it was always opened with FMODE_READ | FMODE_WRITE.
(Note that dm_get_device() still allows read-only dm devices to be used
read-write at the moment: If I create a read-only linear device for the
metadata, via dmsetup load --readonly, then I can still create a rw pool
out of it.)
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Fri, 10 May 2013 13:37:15 +0000 (14:37 +0100)]
dm bufio: avoid a possible __vmalloc deadlock
This patch uses memalloc_noio_save to avoid a possible deadlock in
dm-bufio. (it could happen only with large block size, at most
PAGE_SIZE << MAX_ORDER (typically 8MiB).
__vmalloc doesn't fully respect gfp flags. The specified gfp flags are
used for allocation of requested pages, structures vmap_area, vmap_block
and vm_struct and the radix tree nodes.
However, the kernel pagetables are allocated always with GFP_KERNEL.
Thus the allocation of pagetables can recurse back to the I/O layer and
cause a deadlock.
This patch uses the function memalloc_noio_save to set per-process
PF_MEMALLOC_NOIO flag and the function memalloc_noio_restore to restore
it. When this flag is set, all allocations in the process are done with
implied GFP_NOIO flag, thus the deadlock can't happen.
This should be backported to stable kernels, but they don't have the
PF_MEMALLOC_NOIO flag and memalloc_noio_save/memalloc_noio_restore
functions. So, PF_MEMALLOC should be set and restored instead.
Mike Snitzer [Fri, 10 May 2013 13:37:14 +0000 (14:37 +0100)]
dm stripe: fix regression in stripe_width calculation
Fix a regression in the calculation of the stripe_width in the
dm stripe target which led to incorrect processing of device limits.
The stripe_width is the stripe device length divided by the number of
stripes. The group of commits in the range f14fa69 ("dm stripe: fix
size test") to eb850de ("dm stripe: support for non power of 2
chunksize") interfered with each other (a merging error) and led to the
stripe_width being set incorrectly to the stripe device length divided by
chunk_size * stripe_count.
For example, a stripe device's table with: 0 33553920 striped 3 512 ...
should result in a stripe_width of 11184640 (33553920 / 3), but due to
the bug it was getting set to 21845 (33553920 / (512 * 3)).
The impact of this bug is that device topologies that previously worked
fine with the stripe target are no longer considered valid. In
particular, there is a higher risk of seeing this issue if one of the
stripe devices has a 4K logical block size. Resulting in an error
message like this:
"device-mapper: table: 253:4: len=21845 not aligned to h/w logical block size 4096 of dm-1"
The fix is to swap the order of the divisions and to use a temporary
variable for the second one, so that width retains the intended
value.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org # 3.6+ Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The commit introduced a regression with AD codecs where the stream is
always clean up. Since the patch is just a minor optimization and
reverting the commit fixes the issue, let's just revert it.
tracing/kprobes: Pass trace_probe directly from dispatcher
Pass the pointer of struct trace_probe directly from probe
dispatcher to handlers. This removes redundant container_of
macro uses. Same thing has already done in trace_uprobe.
ftrace: Fix function probe when more than one probe is added
When the first function probe is added and the function tracer
is updated the functions are modified to call the probe.
But when a second function is added, it updates the function
records to have the second function also update, but it fails
to update the actual function itself.
This prevents the second (or third or forth and so on) probes
from having their functions called.
ftrace: Fix the output of enabled_functions debug file
The enabled_functions debugfs file was created to be able to see
what functions have been modified from nops to calling a tracer.
The current method uses the counter in the function record.
As when a ftrace_ops is registered to a function, its count
increases. But that doesn't mean that the function is actively
being traced. /proc/sys/kernel/ftrace_enabled can be set to zero
which would disable it, as well as something can go wrong and
we can think its enabled when only the counter is set.
The record's FTRACE_FL_ENABLED flag is set or cleared when its
function is modified. That is a much more accurate way of knowing
what function is enabled or not.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
tracing: Add helper function trace_create_new_event() to remove duplicate code
Both __trace_add_new_event() and __trace_early_add_new_event() do
basically the same thing, except that __trace_add_new_event() does
a little more.
Instead of having duplicate code between the two functions, add
a helper function trace_create_new_event() that both can use.
This will help against having bugs fixed in one function but not
the other.
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
projects / karo-tx-linux.git / log