Jayachandran C [Wed, 31 Oct 2012 12:01:35 +0000 (12:01 +0000)]
MIPS: Netlogic: Pass cpuid to early_init_secondary
The cpuid was not passed into early_init_secondary even though the
comment indicated that it will be. Fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4458 Signed-off-by: John Crispin <blogic@openwrt.org>
Jayachandran C [Wed, 31 Oct 2012 12:01:34 +0000 (12:01 +0000)]
MIPS: Netlogic: Fix interrupt table entry init
Used the hardware thread id passed in while writing to IRT in
nlm_pic_init_irt()
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4465 Signed-off-by: John Crispin <blogic@openwrt.org>
Jayachandran C [Wed, 31 Oct 2012 12:01:33 +0000 (12:01 +0000)]
MIPS: Netlogic: Fix DMA zone selection for 64-bit
Fix Kconfig for both XLR and XLP to select ZONE_DMA32 (instead of ZONE_DMA)
in case of 64-bit compilation. This can be used for devices that can only
do DMA to 32-bit address. ZONE_DMA is not useful on XLR or XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4466 Signed-off-by: John Crispin <blogic@openwrt.org>
Jayachandran C [Wed, 31 Oct 2012 12:01:32 +0000 (12:01 +0000)]
MIPS: Netlogic: Move fdt init to plat_mem_setup
At this point early printk is available, so debugging device tree
issues is easier.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4460 Signed-off-by: John Crispin <blogic@openwrt.org>
Jayachandran C [Wed, 31 Oct 2012 12:01:30 +0000 (12:01 +0000)]
MIPS: Netlogic: Enable SUE bit in cores
Enable Speculative Unmap Enable bit, which will enable speculative L2
cache requests for unmapped memory. This should give better performance
for kernel code/data which is in KSEG0
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4461 Signed-off-by: John Crispin <blogic@openwrt.org>
Jayachandran C [Wed, 31 Oct 2012 12:01:29 +0000 (12:01 +0000)]
MIPS: Netlogic: select MIPSR2 for XLP
This allows us to use the r2 optimized code from kernel headers
while compilation.
Disable PGD_C0_CONTEXT option for XLP, which does not work.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4456 Signed-off-by: John Crispin <blogic@openwrt.org>
Zi Shen Lim [Wed, 31 Oct 2012 12:01:28 +0000 (12:01 +0000)]
MIPS: perf: Add XLP support for hardware perf.
Add support for XLP performance counters register in perf. Update
mips/Kconfig so that perf events can be selected for XLP.
Signed-off-by: Zi Shen Lim <zlim@netlogicmicro.com> Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4457 Signed-off-by: John Crispin <blogic@openwrt.org>
Madhusudan Bhat [Wed, 31 Oct 2012 12:01:27 +0000 (12:01 +0000)]
MIPS: oprofile: Support for XLR/XLS processors
Add support for XLR and XLS processors in MIPS Oprofile code. These
processors are multi-threaded and have two counters per core. Each
counter can track either all the events in the core (global mode),
or events in just one thread.
We use the counters in the global mode, and use only the first thread
in each core to handle the configuration etc.
Signed-off-by: Madhusudan Bhat <mbhat@netlogicmicro.com> Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4471 Signed-off-by: John Crispin <blogic@openwrt.org>
Jonas Gorski [Wed, 7 Nov 2012 08:25:28 +0000 (08:25 +0000)]
MIPS: BCM63XX: move nvram functions into their own file
Refactor nvram related functions into its own unit for easier expansion
and exposure of the values to other drivers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4516 Signed-off-by: John Crispin <blogic@openwrt.org>
Jonas Gorski [Sun, 28 Oct 2012 12:17:55 +0000 (12:17 +0000)]
MIPS: BCM63XX: use the new reset helper
Use the new reset helper where appropriate.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4453 Signed-off-by: John Crispin <blogic@openwrt.org>
Jonas Gorski [Sun, 28 Oct 2012 12:17:54 +0000 (12:17 +0000)]
MIPS: BCM63XX: add core reset helper
Add a reset helper for resetting the different cores.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4455 Signed-off-by: John Crispin <blogic@openwrt.org>
Jonas Gorski [Sun, 28 Oct 2012 12:17:53 +0000 (12:17 +0000)]
MIPS: BCM63XX: add softreset register description for BCM6358
The softreset register description for BCM6358 was missing, so add it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4454 Signed-off-by: John Crispin <blogic@openwrt.org>
Hauke Mehrtens [Wed, 3 Oct 2012 11:34:20 +0000 (11:34 +0000)]
MIPS: BCM47xx: sprom: read values without prefix as fallback
There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.
The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364 Signed-off-by: John Crispin <blogic@openwrt.org>
Hauke Mehrtens [Wed, 3 Oct 2012 11:34:18 +0000 (11:34 +0000)]
MIPS: BCM47xx: read out full board data
Read out the full board data independently of the sprom version. Now we
also get the full boardflags and so on if sromrev is not set and our
code would assume a rev 1 device. When a nvram option is not set
because it is not there this is no problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4363 Signed-off-by: John Crispin <blogic@openwrt.org>
Hauke Mehrtens [Wed, 3 Oct 2012 11:34:17 +0000 (11:34 +0000)]
MIPS: BCM47XX: improve memory size detection
The memory size is detected by finding a place where it repeats in
memory. Currently we are just checking when the function prom_init is
seen again, but it is better to check for a bigger part of the memory
to decrease the chance of wrong results.
This should fix a problem we saw in OpenWrt, where the detected
available memory decreed on some devices when doing a soft reboot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4362 Signed-off-by: John Crispin <blogic@openwrt.org>
Hauke Mehrtens [Wed, 3 Oct 2012 11:34:16 +0000 (11:34 +0000)]
MIPS: BCM47XX: ignore last memory page
Ignoring the last page when ddr size is 128M. Cached accesses to last
page is causing the processor to prefetch using address above 128M
stepping out of the ddr address space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4365 Signed-off-by: John Crispin <blogic@openwrt.org>
Shane McDonald [Thu, 14 Jun 2012 02:26:40 +0000 (02:26 +0000)]
MIPS: Move processing of coherency kernel parameters earlier
Commit 97ce2c88f9ad42e3c60a9beb9fca87abf3639faa (jump-label: initialize
jump-label subsystem much earlier) caused MIPS to break, so this was
resolved with commit 6650df3c380e0db558dbfec63ed860402c6afb2a (MIPS:
Move cache setup to setup_arch().). Unfortunately, after this commit,
the coherency kernel parameters, cca and coherentio, are no longer
processed before their values are used.
This patch fixes this problem by marking them as early_param, which
results in them being processed before they are needed.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com> Acked-by: David Daney <david.daney@cavium.com> Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/3961 Signed-off-by: John Crispin <blogic@openwrt.org>
Charles Hardin [Wed, 5 Sep 2012 19:19:48 +0000 (19:19 +0000)]
mips/octeon: 16-Bit NOR flash was not being detected during boot
The cavium code assumed that all NOR on the boot bus was
an 8-bit NOR part and hardcoded the bankwidth. The simple
solution was to add the code that queries the configuration
register for the width of the bus that has been hardware strapped
to the Cavium. This allows both 8-bit and 16-bit parts to be
discovered during boot.
Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Charles Hardin <ckhardin@exablox.com>
Patchwork: http://patchwork.linux-mips.org/patch/4323 Signed-off-by: John Crispin <blogic@openwrt.org>
Kevin Cernekee [Wed, 7 Nov 2012 18:39:48 +0000 (18:39 +0000)]
MIPS: tlbex: Fix section mismatches
The new functions introduced in commit 02a5417751 (MIPS: tlbex: Deal with
re-definition of label) should be marked __cpuinit, to eliminate a
warning that can pop up when CONFIG_EXPORT_UASM is disabled:
LD arch/mips/mm/built-in.o
WARNING: arch/mips/mm/built-in.o(.text+0x2a4c): Section mismatch in reference from the function uasm_bgezl_hazard() to the function .cpuinit.text:uasm_il_bgezl()
The function uasm_bgezl_hazard() references
the function __cpuinit uasm_il_bgezl().
This is often because uasm_bgezl_hazard lacks a __cpuinit
annotation or the annotation of uasm_il_bgezl is wrong.
WARNING: arch/mips/mm/built-in.o(.text+0x2a68): Section mismatch in reference from the function uasm_bgezl_label() to the function .cpuinit.text:uasm_build_label()
The function uasm_bgezl_label() references
the function __cpuinit uasm_build_label().
This is often because uasm_bgezl_label lacks a __cpuinit
annotation or the annotation of uasm_build_label is wrong.
(This warning might not occur if the function was inlined.)
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4517 Signed-off-by: John Crispin <blogic@openwrt.org>
Pull gfs2 fixes from Steven Whitehouse:
"Here are a number of GFS2 bug fixes. There are three from Andy Price
which fix various issues spotted by automated code analysis. There
are two from Lukas Czerner fixing my mistaken assumptions as to how
FITRIM should work. Finally Ben Marzinski has fixed a bug relating to
mmap and atime and also a bug relating to a locking issue in the
transaction code."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Test bufdata with buffer locked and gfs2_log_lock held
GFS2: Don't call file_accessed() with a shared glock
GFS2: Fix FITRIM argument handling
GFS2: Require user to provide argument for FITRIM
GFS2: Clean up some unused assignments
GFS2: Fix possible null pointer deref in gfs2_rs_alloc
GFS2: Fix an unchecked error from gfs2_rs_alloc
GFS2: Test bufdata with buffer locked and gfs2_log_lock held
In gfs2_trans_add_bh(), gfs2 was testing if a there was a bd attached to the
buffer without having the gfs2_log_lock held. It was then assuming it would
stay attached for the rest of the function. However, without either the log
lock being held of the buffer locked, __gfs2_ail_flush() could detach bd at any
time. This patch moves the locking before the test. If there isn't a bd
already attached, gfs2 can safely allocate one and attach it before locking.
There is no way that the newly allocated bd could be on the ail list,
and thus no way for __gfs2_ail_flush() to detach it.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
GFS2: Don't call file_accessed() with a shared glock
file_accessed() was being called by gfs2_mmap() with a shared glock. If it
needed to update the atime, it was crashing because it dirtied the inode in
gfs2_dirty_inode() without holding an exclusive lock. gfs2_dirty_inode()
checked if the caller was already holding a glock, but it didn't make sure that
the glock was in the exclusive state. Now, instead of calling file_accessed()
while holding the shared lock in gfs2_mmap(), file_accessed() is called after
grabbing and releasing the glock to update the inode. If file_accessed() needs
to update the atime, it will grab an exclusive lock in gfs2_dirty_inode().
gfs2_dirty_inode() now also checks to make sure that if the calling process has
already locked the glock, it has an exclusive lock.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Lukas Czerner [Tue, 16 Oct 2012 09:39:08 +0000 (11:39 +0200)]
GFS2: Fix FITRIM argument handling
Currently implementation in gfs2 uses FITRIM arguments as it were in
file system blocks units which is wrong. The FITRIM arguments
(fstrim_range.start, fstrim_range.len and fstrim_range.minlen) are
actually in bytes.
Moreover, check for start argument beyond the end of file system, len
argument being smaller than file system block and minlen argument being
bigger than biggest resource group were missing.
This commit converts the code to convert FITRIM argument to file system
blocks and also adds appropriate checks mentioned above.
All the problems were recognised by xfstests 251 and 260.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Lukas Czerner [Tue, 16 Oct 2012 09:39:07 +0000 (11:39 +0200)]
GFS2: Require user to provide argument for FITRIM
When the fstrim_range argument is not provided by user in FITRIM ioctl
we should just return EFAULT and not promoting bad behaviour by filling
the structure in kernel. Let the user deal with it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Andrew Price [Fri, 12 Oct 2012 15:45:09 +0000 (16:45 +0100)]
GFS2: Fix possible null pointer deref in gfs2_rs_alloc
Despite the return value from kmem_cache_zalloc() being checked, the
error wasn't being returned until after a possible null pointer
dereference. This patch returns the error immediately, allowing the
removal of the error variable.
Signed-off-by: Andrew Price <anprice@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Linus Torvalds [Wed, 7 Nov 2012 03:16:41 +0000 (04:16 +0100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A single radeon typo fix for a regressions and two fixes for a
regression in the open helper address space stuff."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix typo in evergreen_mc_resume()
drm: set dev_mapping before calling drm_open_helper
drm: restore open_count if drm_setup fails
Linus Torvalds [Wed, 7 Nov 2012 03:14:45 +0000 (04:14 +0100)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull arm fixes from Russell King:
"Not much here again.
The two most notable things here are the sched_clock() fix, which was
causing problems with the scheduling of threaded IRQs after a suspend
event, and the vfp fix, which afaik has only been seen on some older
OMAP boards. Nevertheless, both are fairly important fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7569/1: mm: uninitialized warning corrections
ARM: 7567/1: io: avoid GCC's offsettable addressing modes for halfword accesses
ARM: 7566/1: vfp: fix save and restore when running on pre-VFPv3 and CONFIG_VFPv3 set
ARM: 7565/1: sched: stop sched_clock() during suspend
Alex Deucher [Mon, 5 Nov 2012 16:34:58 +0000 (16:34 +0000)]
drm/radeon: fix typo in evergreen_mc_resume()
Add missing index that may have led us to enabling
more crtcs than necessary.
May also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=56139
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jean Delvare [Mon, 5 Nov 2012 20:54:40 +0000 (21:54 +0100)]
hwmon: Fix chip feature table headers
These got broken by recent patches fixing checkpatch warnings in these
drivers. The trick is that the patches themselves looked good, but the
source files after applying them do not. That's why I am not a big fan
of using tabs inside comments.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <linux@roeck-us.net>
Jean Delvare [Mon, 5 Nov 2012 20:54:39 +0000 (21:54 +0100)]
hwmon: (w83627ehf) Force initial bank selection
Don't assume bank 0 is selected at device probe time. This may not be
the case. Force bank selection at first register access to guarantee
that we read the right registers upon driver loading.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org
The variables here are really not used uninitialized.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 3 Nov 2012 22:27:21 +0000 (15:27 -0700)]
Merge tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a bunch of deadlock situations:
* State recovery can deadlock if we fail to release sequence ids
before scheduling the recovery thread.
* Calling deactivate_super() from an RPC workqueue thread can
deadlock because of the call to rpc_shutdown_client.
- Display the device name correctly in /proc/*/mounts
- Fix a number of incorrect error return values:
* When NFSv3 mounts fail due to a timeout.
* On NFSv4.1 backchannel setup failure
* On NFSv4 open access checks
- pnfs_find_alloc_layout() must check the layout pointer for NULL
- Fix a regression in the legacy DNS resolved
* tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4: nfs4_opendata_access should return errno
NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly
SUNRPC: return proper errno from backchannel_rqst
NFS: add nfs_sb_deactive_async to avoid deadlock
nfs: Show original device name verbatim in /proc/*/mount{s,info}
nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts
nfs: Check whether a layout pointer is NULL before free it
NFS: fix bug in legacy DNS resolver.
NFSv4: nfs4_locku_done must release the sequence id
NFSv4.1: We must release the sequence id when we fail to get a session slot
NFS: Wait for session recovery to finish before returning
Linus Torvalds [Sat, 3 Nov 2012 22:25:14 +0000 (15:25 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management & ACPI update from Zhang Rui,
Ho humm. Normally these things go through Len. But it's just three
small fixes, I guess I can pull directly too.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
ACPI video: Ignore errors after _DOD evaluation.
thermal: solve compilation errors in rcar_thermal
Linus Torvalds [Sat, 3 Nov 2012 22:14:54 +0000 (15:14 -0700)]
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"Two patches are usual stuff.
The bigger patch is needed to correct a wrong decision made in this
merge window. We hoped to get the PIOQUEUE mode in the mxs driver
working with DMA, but it turned out to be too broken (leading to data
loss), so we now think it is best to remove it entirely and work only
with DMA now. The patch should be in 3.7. IMO, so users never get
the chance to use both modes in parallel."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: set irq name as device name
i2c-nomadik: Fixup clock handling
i2c: mxs: remove broken PIOQUEUE support
it's slightly bigger than I'd probably like, but nothing looked
dangerous enough to hold off on."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/udl: fix stride issues scanning out stride != width*bpp
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
Pavel Emelyanov [Mon, 29 Oct 2012 05:05:33 +0000 (05:05 +0000)]
tcp-repair: Handle zero-length data put in rcv queue
When sending data into a tcp socket in repair state we should check
for the amount of data being 0 explicitly. Otherwise we'll have an skb
with seq == end_seq in rcv queue, but tcp doesn't expect this to happen
(in particular a warn_on in tcp_recvmsg shoots).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Parkin [Mon, 29 Oct 2012 23:41:48 +0000 (23:41 +0000)]
l2tp: fix oops in l2tp_eth_create() error path
When creating an L2TPv3 Ethernet session, if register_netdev() should fail for
any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the
32k-interface limit), the netdev is freed in the error path. However, the
l2tp_eth_sess structure's dev pointer is left uncleared, and this results in
l2tp_eth_delete() then attempting to unregister the same netdev later in the
session teardown. This results in an oops.
To avoid this, clear the session dev pointer in the error path.
Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Murzov [Sat, 13 Oct 2012 00:41:25 +0000 (04:41 +0400)]
ACPI video: Ignore errors after _DOD evaluation.
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.
Devendra Naga [Wed, 31 Oct 2012 08:46:10 +0000 (17:46 +0900)]
thermal: solve compilation errors in rcar_thermal
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Vipul Pandya [Mon, 29 Oct 2012 02:02:36 +0000 (02:02 +0000)]
cxgb4: Fix unable to get UP event from the LLD
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com> Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Tested-by: Roland Stigge <stigge@antcom.de> Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 28 Oct 2012 21:59:04 +0000 (21:59 +0000)]
bnx2x: fix HW initialization using fw 7.8.x
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more scsi target fixes from Nicholas Bellinger:
"This series is a second round of target fixes for v3.7-rc4 that have
come into target-devel over the last days, and are important enough to
be applied ASAP.
All are being CC'ed to stable. The most important two are:
- target: Re-add explict zeroing of INQUIRY bounce buffer memory to
fix a regression for handling zero-length payloads, a bug that went
during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo)
- iscsi-target: Fix a long-standing missed R2T wakeup race in TX
thread processing when using a single queue slot. (Roland)
Thanks to Roland & PureStorage team for helping to track down this
long standing race with iscsi-target single queue slot operation.
Also, the tcm_fc(FCoE) regression bug that was observed recently with
-rc2 code has also been resolved with the cancel_delayed_work() return
bugfix (commit c0158ca64da5: "workqueue: cancel_delayed_work() should
return %false if work item is idle") now in -rc3. Thanks again to Yi
Zou, MDR, Robert Love @ Intel for helping to track this down."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
iscsi-target: Fix missed wakeup race in TX thread
target: Avoid integer overflow in se_dev_align_max_sectors()
target: Don't return success from module_init() if setup fails
target: Re-add explict zeroing of INQUIRY bounce buffer memory
Linus Torvalds [Fri, 2 Nov 2012 20:27:52 +0000 (13:27 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"An e-mail address update, and fix a compile error on SPARC"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Only include of_match_table with CONFIG_OF_GPIO
hwmon, fam15h_power: Change email address, MAINTAINERS entry
Linus Torvalds [Fri, 2 Nov 2012 20:27:01 +0000 (13:27 -0700)]
Merge tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv
Pull FRV fixes from David Howells:
"A collection of small fixes for the FRV architecture."
* tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv:
frv: fix the broken preempt
frv: switch to saner kernel_execve() semantics
FRV: Fix the new-style kernel_thread() stuff
FRV: Fix the preemption handling
FRV: gcc-4.1.2 also inlines weak functions
FRV: Don't objcopy the GNU build_id note
FRV: Add missing linux/export.h #inclusions
Linus Torvalds [Fri, 2 Nov 2012 20:26:11 +0000 (13:26 -0700)]
Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
Sasha Levin [Tue, 30 Oct 2012 18:45:57 +0000 (14:45 -0400)]
hashtable: introduce a small and naive hashtable
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Fri, 2 Nov 2012 16:05:44 +0000 (12:05 -0400)]
frv: fix the broken preempt
Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then. Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Fri, 2 Nov 2012 13:20:43 +0000 (13:20 +0000)]
FRV: Fix the new-style kernel_thread() stuff
The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:
commit 02ce496f152df87be081a64796498942c433a2fd
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Tue Sep 18 22:18:51 2012 -0400
Subject: frv: split ret_from_fork, simplify kernel_thread() a lot
The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that. Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.
Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: Fix the preemption handling
Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.
Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>
Wolfram Sang [Fri, 12 Oct 2012 10:55:16 +0000 (11:55 +0100)]
i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de>
Linus Torvalds [Fri, 2 Nov 2012 00:48:19 +0000 (17:48 -0700)]
Merge tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux
Pull Xtensa fixes from Chris Zankel:
"Some important bug fixes.
With the change to uapi, there was a bug introduced that results in an
empty syscall table (mult-inclusion bug). Switching to the generic
thread/execve allowed us to fix a bug we had in vfork()."
* tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux:
xtensa: switch to generic sys_execve()
xtensa: switch to generic kernel_execve()
xtensa: switch to generic kernel_thread()
xtensa: reset windowbase/windowstart when cloning the VM
xtensa: use physical addresses for bus addresses
xtensa: allow multi-inclusion for uapi/unistd.h
Dave Airlie [Thu, 1 Nov 2012 03:47:09 +0000 (13:47 +1000)]
drm/udl: fix stride issues scanning out stride != width*bpp
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.
This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Jamie Lentin [Thu, 1 Nov 2012 23:55:43 +0000 (23:55 +0000)]
hwmon: Only include of_match_table with CONFIG_OF_GPIO
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Dave Airlie [Fri, 2 Nov 2012 00:30:37 +0000 (10:30 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Inki writes:
"As I posted before, we have added a new git repository for Exynos drm
to MAINTAINERS file so change it to new one like below,
from git://git.infradead.org/users/kmpark/linux-samsung
to git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos
And this pull request includes the following:
- fix display on issue when user requested dpms mode changing.
- add git repository for Exynos drm to MAINTAINERS file.
- add support for ARCH_MULTIPLATFORM.
- and code clean."
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
Dave Airlie [Fri, 2 Nov 2012 00:29:22 +0000 (10:29 +1000)]
Merge branch 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
"This request is mostly load detection fixes from Egbert and me."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
Dave Airlie [Fri, 2 Nov 2012 00:26:03 +0000 (10:26 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes"
Nothing big at all for -fixes, just small stuff:
- Two patches to fix bugs on i830M
- ums regression fixer due to kicking firmeware fbs (Chris)
- tune down a too loud warning (Jani)
- be more careful with sdvo infoframes, which fixes a long-standing
sdvo-hdmi regression"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Reading TCP stats when using TCP Illinois congestion control algorithm
can cause a divide by zero kernel oops.
The division by zero occur in tcp_illinois_info() at:
do_div(t, ca->cnt_rtt);
where ca->cnt_rtt can become zero (when rtt_reset is called)
Steps to Reproduce:
1. Register tcp_illinois:
# sysctl -w net.ipv4.tcp_congestion_control=illinois
2. Monitor internal TCP information via command "ss -i"
# watch -d ss -i
3. Establish new TCP conn to machine
Either it fails at the initial conn, or else it needs to wait
for a loss or a reset.
This is only related to reading stats. The function avg_delay() also
performs the same divide, but is guarded with a (ca->cnt_rtt > 0) at its
calling point in update_params(). Thus, simply fix tcp_illinois_info().
Function tcp_illinois_info() / get_info() is called without
socket lock. Thus, eliminate any race condition on ca->cnt_rtt
by using a local stack variable. Simply reuse info.tcpv_rttcnt,
as its already set to ca->cnt_rtt.
Function avg_delay() is not affected by this race condition, as
its called with the socket lock.
Cc: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida [Wed, 31 Oct 2012 05:48:19 +0000 (05:48 +0000)]
net: sctp: Fix typo in net/sctp
Correct spelling typo in net/sctp/socket.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Note: Sorry for the second patch but I missed this one while checking
the file. You can squash them into one patch. Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:57 +0000 (05:46 +0000)]
bnx2x: Fix no link on 577xx 10G-baseT
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:56 +0000 (05:46 +0000)]
bnx2x: Fix unrecognized SFP+ module after driver is loaded
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:55 +0000 (05:46 +0000)]
bnx2x: Fix potential incorrect link speed provision
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:54 +0000 (05:46 +0000)]
bnx2x: Restore global registers back to default.
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Wed, 31 Oct 2012 22:30:54 +0000 (22:30 +0000)]
ixgbe: PTP get_ts_info missing software support
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> CC: Stable <stable@vger.kernel.org> [3.5] Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Deucher [Wed, 31 Oct 2012 15:51:03 +0000 (11:51 -0400)]
drm/radeon: add load detection support for ext DAC on R200 (v2)
The R200 asics use an external DAC for the secondary DAC.
The current KMS code tries to use code for the integrated
TV DAC for R200 which leads to unpredictable results since
R200 does not have an integrated TV DAC. This patch ports
the external DAC load detection support from the UMS
driver to KMS.
v2: fix typo in loop break logic
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Egbert Eich <eich@suse.de>
Egbert Eich [Mon, 29 Oct 2012 12:46:48 +0000 (13:46 +0100)]
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
On all dual CRTC GPUs the CRTC_CRT_ON in the RADEON_CRTC_EXT_CNTL register
controls the CRTC of the primary DAC. Therefore it is set in the DAC DMPS
function.
This is different for GPU's with a single CRTC but a primary and a
TV DAC: here it controls the single CRTC no matter where it is routed.
Therefore we set it here. This avoids an elaborate on/off state tracking
since both primary_dac_dpms() and tv_dac_dpms() functions would have
to touch this bit.
On single CRTC GPUs with just one DAC it's irrelevant where this bit
is handled.
agd5f: fix warning
Signed-off-by: Egbert Eich <eich@suse.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / karo-tx-linux.git / log