Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few driver-specific fixes for ASoC and HD-audio."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix no sound from ALC662 after Windows reboot
ASoC: tlv320aic3x: Fix codec pll configure bug
ASoC: wm2200: Add missing BCLK rate
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One regression fix, two radeon fixes (one for an oops), and an i915
fix to unload framebuffers earlier.
We originally were going to leave the i915 fix until -next, but grub2
in some situations causes vesafb/efifb to be loaded now, and this
causes big slowdowns, and I have reports in rawhide I'd like to have
fixed."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: kick any firmware framebuffers before claiming the gtt
drm: edid: Don't add inferred modes with higher resolution
drm/radeon: fix rare segfault
drm/radeon: fix VM page table setup on SI
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"md: collection of bug fixes for 3.5
You go away for 2 weeks vacation and what do you get when you come
back? Piles of bugs :-)
Some found by inspection, some by testing, some during use in the
field, and some while developing for the next window..."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: fix up plugging (again).
md: support re-add of recovering devices.
md/raid1: fix bug in read_balance introduced by hot-replace
raid5: delayed stripe fix
md/raid456: When read error cannot be recovered, record bad block
md: make 'name' arg to md_register_thread non-optional.
md/raid10: fix failure when trying to repair a read error.
md/raid5: fix refcount problem when blocked_rdev is set.
md:Add blk_plug in sync_thread.
md/raid5: In ops_run_io, inc nr_pending before calling md_wait_for_blocked_rdev
md/raid5: Do not add data_offset before call to is_badblock
md/raid5: prefer replacing failed devices over want-replacement devices.
md/raid10: Don't try to recovery unmatched (and unused) chunks.
Milan Broz [Tue, 3 Jul 2012 11:55:41 +0000 (12:55 +0100)]
dm: verity fix documentation
Veritysetup is now part of cryptsetup package.
Remove on-disk header description (which is not parsed in kernel)
and point users to cryptsetup where it the format is documented.
Mention units for block size paramaters.
Fix target line specification and dmsetup parameters.
Signed-off-by: Milan Broz <mbroz@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Tue, 3 Jul 2012 11:55:37 +0000 (12:55 +0100)]
dm persistent data: fix allocation failure in space map checker init
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a
sufficiently-large metadata device is used in a thin pool then the space
map checker will fail to allocate the memory it requires.
Switch from kmalloc to vmalloc to allow larger virtually contiguous
allocations for the space map checker's internal count arrays.
Reported-by: Vivek Goyal <vgoyal@redhat.com> Cc: stable@kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Tue, 3 Jul 2012 11:55:35 +0000 (12:55 +0100)]
dm persistent data: handle space map checker creation failure
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create()
fails, dm_tm_create_internal() would still return success even though it
cleaned up all resources it was supposed to have created. This will
lead to a kernel crash:
Joe Thornber [Tue, 3 Jul 2012 11:55:31 +0000 (12:55 +0100)]
dm thin: commit metadata before creating metadata snapshot
Userland sometimes sees a corrupt metadata block if metadata is changing
rapidly when a metadata snapshot is reserved for userland, To make the
problem go away, commit before we take the metadata snapshot (which is a
sensible thing to do anyway).
The checksums mean userland spots this corruption immediately so there's
no risk of acting on incorrect data. No corruption exists from the
kernel's point of view, and thin_check passes after pool shutdown.
I believe this is to do with shared blocks at the first level of the
{device, mapping} btree. Prior to the metadata-snap support no sharing
at this level was possible, so this patch is only required after commit cc8394d86f045b86ff303d3c9e4ce47d97148951 ("dm thin: provide userspace
access to pool metadata").
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Paul Mundt [Mon, 2 Jul 2012 05:34:11 +0000 (14:34 +0900)]
security: Fix nommu build.
The security + nommu configuration presently blows up with an undefined
reference to BDI_CAP_EXEC_MAP:
security/security.c: In function 'mmap_prot':
security/security.c:687:36: error: dereferencing pointer to incomplete type
security/security.c:688:16: error: 'BDI_CAP_EXEC_MAP' undeclared (first use in this function)
security/security.c:688:16: note: each undeclared identifier is reported only once for each function it appears in
include backing-dev.h directly to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: James Morris <james.l.morris@oracle.com>
Daniel Vetter [Sun, 1 Jul 2012 15:09:42 +0000 (17:09 +0200)]
drm/i915: kick any firmware framebuffers before claiming the gtt
Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.
Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.
Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...
v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling
v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.
v4: Jani Nikula complained about the pointless bool primary
initialization.
v5: Don't oops if we can't allocate, noticed by Chris Wilson.
v6: Resolve conflicts with agp rework and fixup whitespace.
Backport to 3.5 -fixes queue requested by Dave Airlie - due to grub
using vesa on fedora their initrd seems to load vesafb before loading
the real kms driver. So tons more people actually experience a
dead-slow gpu. Hence also the Cc: stable.
Cc: stable@vger.kernel.org Reported-and-tested-by: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm: edid: Don't add inferred modes with higher resolution
When a monitor EDID doesn't give the preferred bit, driver assumes
that the mode with the higest resolution and rate is the preferred
mode. Meanwhile the recent changes for allowing more modes in the
GFT/CVT ranges give actually more modes, and some modes may be over
the native size. Thus such a mode would be picked up as the preferred
mode although it's no native resolution.
For avoiding such a problem, this patch limits the addition of
inferred modes by checking not to be greater than other modes.
Also, it checks the duplicated mode entry at the same time.
Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
In gem idle/busy ioctl the radeon object was derefenced after
drm_gem_object_unreference_unlocked which in case the object
have been destroyed lead to use of a possibly free pointer with
possibly wrong data.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
We currently only allow a device to be re-added if it appear to be
in-sync. This is overly restrictive as it may be desirable to re-add
a device that is in the middle of recovery.
So remove the test for "InSync" - the test on rdev->raid_disk is
sufficient to ensure that the re-add will succeed.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com> Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid1: fix bug in read_balance introduced by hot-replace
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Shaohua Li [Tue, 3 Jul 2012 05:57:19 +0000 (15:57 +1000)]
raid5: delayed stripe fix
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
md: make 'name' arg to md_register_thread non-optional.
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org Reported-by: Christian Balzer <chibi@gol.com> Signed-off-by: NeilBrown <neilb@suse.de>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull a couple more powerpc fixes from Benjamin Herrenschmidt:
"Here are two more fixes that I "missed" when scrubbing patchwork last
week which are worth still having in 3.5."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/kvm: sldi should be sld
powerpc/xmon: Use cpumask iterator to avoid warning
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
md/raid5: In ops_run_io, inc nr_pending before calling md_wait_for_blocked_rdev
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7969ef5477d
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
majianpeng [Tue, 12 Jun 2012 00:31:10 +0000 (08:31 +0800)]
md/raid5: Do not add data_offset before call to is_badblock
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf3563140e639
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
md/raid5: prefer replacing failed devices over want-replacement devices.
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
md/raid10: Don't try to recovery unmatched (and unused) chunks.
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org Reported-by: Christian Balzer <chibi@gol.com> Tested-by: Christian Balzer <chibi@gol.com> Signed-off-by: NeilBrown <neilb@suse.de>
Anton Blanchard [Thu, 28 Jun 2012 19:28:57 +0000 (19:28 +0000)]
powerpc/xmon: Use cpumask iterator to avoid warning
We have a bug report where the kernel hits a warning in the cpumask
code:
WARNING: at include/linux/cpumask.h:107
Which is:
WARN_ON_ONCE(cpu >= nr_cpumask_bits);
The backtrace is:
cpu_cmd
cmds
xmon_core
xmon
die
xmon is iterating through 0 to NR_CPUS. I'm not sure why we are still
open coding this but iterating above nr_cpu_ids is definitely a bug.
This patch iterates through all possible cpus, in case we issue a
system reset and CPUs in an offline state call in.
Perhaps the old code was trying to handle CPUs that were in the
partition but were never started (eg kexec into a kernel with an
nr_cpus= boot option). They are going to die way before we get into
xmon since we haven't set any kernel state up for them.
Signed-off-by: Anton Blanchard <anton@samba.org> CC: <stable@kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull two ARM fixes from Russell King:
"It's been fairly quiet with the fixes. Just two this time. One fixes
a long standing problem with KALLSYMS needing an additional pass, and
the other sorts a problem with the vmalloc space interacting with
static IO mappings."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7438/1: fill possible PMD empty section gaps
ARM: 7428/1: Prevent KALLSYM size mismatch on ARM.
Nicolas Pitre [Wed, 27 Jun 2012 16:28:57 +0000 (17:28 +0100)]
ARM: 7438/1: fill possible PMD empty section gaps
On ARM with the 2-level page table format, a PMD entry is represented by
two consecutive section entries covering 2MB of virtual space.
However, static mappings always were allowed to use separate 1MB section
entries. This means in practice that a static mapping may create half
populated PMDs via create_mapping().
Since commit 0536bdf33f (ARM: move iotable mappings within the vmalloc
region) those static mappings are located in the vmalloc area. We must
ensure no such half populated PMDs are accessible once vmalloc() or
ioremap() start looking at the vmalloc area for nearby free virtual
address ranges, or various things leading to a kernel crash will happen.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: "R, Sricharan" <r.sricharan@ti.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 30 Jun 2012 23:01:50 +0000 (16:01 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems --
mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
Samsung."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6q: fix suspend regression caused by common clk migration
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
Randy Dunlap [Sat, 30 Jun 2012 22:37:24 +0000 (15:37 -0700)]
printk.c: fix kernel-doc warnings
Fix kernel-doc warnings in printk.c: use correct parameter name.
Warning(kernel/printk.c:2429): No description found for parameter 'buf'
Warning(kernel/printk.c:2429): Excess function parameter 'line' description in 'kmsg_dump_get_buffer'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sat, 30 Jun 2012 22:30:46 +0000 (15:30 -0700)]
linux/irq.h: fix kernel-doc warning
Fix kernel-doc warning. This struct member was removed in commit 875682648b89 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.
Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: Richard Weinberger <richard@nod.at> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shawn Guo [Tue, 5 Jun 2012 07:16:43 +0000 (15:16 +0800)]
ARM: imx6q: fix suspend regression caused by common clk migration
When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function. There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 30 Jun 2012 18:11:58 +0000 (11:11 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
Linus Torvalds [Sat, 30 Jun 2012 17:11:24 +0000 (10:11 -0700)]
Merge tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver Core fixes from Greg Kroah-Hartman:
"Here is a number of printk() fixes, specifically a few reported by the
crazy blog program that ships in SUSE releases (that's "boot log" and
not "web log", it predates the general "blog" terminology by many
years), and the restoration of the continuation line functionality
reported by Stephen and others. Yes, the changes seem a bit big this
late in the cycle, but I've been beating on them for a while now, and
Stephen has even optimized it a bit, so all looks good to me.
The other change in here is a Documentation update for the stable
kernel rules describing how some distro patches should be backported,
to hopefully drive a bit more response from the distros to the stable
kernel releases.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
printk: Optimize if statement logic where newline exists
printk: flush continuation lines immediately to console
syslog: fill buffer with more than a single message for SYSLOG_ACTION_READ
Revert "printk: return -EINVAL if the message len is bigger than the buf size"
printk: fix regression in SYSLOG_ACTION_CLEAR
stable: Allow merging of backports for serious user-visible performance issues
Stuart Hayes [Wed, 13 Jun 2012 21:10:45 +0000 (16:10 -0500)]
acpi_pad: fix power_saving thread deadlock
The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread. The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu(). This
patch fixes the issue by making round_robin_cpu() use its own mutex.
https://bugzilla.kernel.org/show_bug.cgi?id=42981
Cc: stable@vger.kernel.org Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com> Signed-off-by: Len Brown <len.brown@intel.com>
Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.
https://bugzilla.kernel.org/show_bug.cgi?id=43168
Cc: Igor Murzov <intergalactic.anonymous@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sat, 30 Jun 2012 02:05:41 +0000 (19:05 -0700)]
Merge tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
* Fix for a bug in async suspend error code path causing parents to
wait forever for their children in case of a suspend error from
Mandeep Singh Baines (-stable metarial).
* Fix for a suspend regression related to earlier changes in the ACPI
cpuidle driver from Deepthi Dharwar.
* tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
PM / Sleep: Prevent waiting forever on asynchronous suspend after abort
Steven Rostedt [Fri, 29 Jun 2012 15:40:11 +0000 (11:40 -0400)]
printk: Optimize if statement logic where newline exists
In reviewing Kay's fix up patch: "printk: Have printk() never buffer its
data", I found two if statements that could be combined and optimized.
Put together the two 'cont.len && cont.owner == current' if statements
into a single one, and check if we need to call cont_add(). This also
removes the unneeded double cont_flush() calls.
Linus Torvalds [Fri, 29 Jun 2012 20:50:11 +0000 (13:50 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few powerpc fixes. Arguably some of this should have come
to you earlier but I'm only just catching up after my medical leave.
Mostly these fixes regressions, a couple are long standing bugs."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Fix software invalidate TCE
powerpc: check_and_cede_processor() never cedes
powerpc/ftrace: Do not trace restore_interrupts()
powerpc: Fix Section mismatch warnings in prom_init.c
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
powerpc: Fix uninitialised error in numa.c
powerpc: Fix BPF_JIT code to link with multiple TOCs
Linus Torvalds [Fri, 29 Jun 2012 17:29:21 +0000 (10:29 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull oprofile fixlet from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: perf: use NR_CPUS instead or nr_cpumask_bits for static array
Kay Sievers [Thu, 28 Jun 2012 07:38:53 +0000 (09:38 +0200)]
printk: flush continuation lines immediately to console
Continuation lines are buffered internally, intended to merge the
chunked printk()s into a single record, and to isolate potentially
racy continuation users from usual terminated line users.
This though, has the effect that partial lines are not printed to
the console in the moment they are emitted. In case the kernel
crashes in the meantime, the potentially interesting printed
information would never reach the consoles.
Here we share the continuation buffer with the console copy logic,
and partial lines are always immediately flushed to the available
consoles. They are still buffered internally to improve the
readability and integrity of the messages and minimize the amount
of needed record headers to store.
Signed-off-by: Kay Sievers <kay@vrfy.org> Tested-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Thu, 28 Jun 2012 21:53:07 +0000 (17:53 -0400)]
drm/radeon: fix VM page table setup on SI
Cayman and trinity allow for variable sized VM page
tables, but SI requires that all page tables be the
same size. The current code assumes variablely sized
VM page tables so SI may end up with part of each page
table overlapping with other memory which could end
up being interpreted by the VM hw as garbage.
Change the code to better accomodate SI. Allocate enough
space for at least 2 full page tables and always set
last_pfn to max_pfn on SI so each VM is backed by a full
page table. This limits us to only 2 VMs active at any
given time on SI. This will be rectified and the code can
be reunified once we move to two level page tables.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Kailang Yang [Fri, 29 Jun 2012 07:35:52 +0000 (09:35 +0200)]
ALSA: hda - Fix no sound from ALC662 after Windows reboot
Windows use hidden register to control EAPD.
Linux use verb to control EAPD.
If windows reboot to Linux, it must change the EAPD control to verb
control.
Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hebbar, Gururaja [Tue, 26 Jun 2012 13:55:11 +0000 (19:25 +0530)]
ASoC: tlv320aic3x: Fix codec pll configure bug
In sound/soc/codecs/tlv320aic3x.c
data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
data | (pll_p << PLLP_SHIFT));
In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.
However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Anton Blanchard [Wed, 27 Jun 2012 13:13:52 +0000 (13:13 +0000)]
powerpc: check_and_cede_processor() never cedes
Commit f948501b36c6 ("Make hard_irq_disable() actually hard-disable
interrupts") caused check_and_cede_processor to stop working.
->irq_happened will never be zero right after a hard_irq_disable
so the compiler removes the call to cede_processor completely.
The bug was introduced back in the lazy interrupt handling rework
of 3.4 but was hidden until recently because hard_irq_disable did
nothing.
This issue will eventually appear in 3.4 stable since the
hard_irq_disable fix is marked stable, so mark this one for stable
too.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Mon, 4 Jun 2012 16:27:54 +0000 (16:27 +0000)]
powerpc/ftrace: Do not trace restore_interrupts()
As I was adding code that affects all archs, I started testing function
tracer against PPC64 and found that it currently locks up with 3.4
kernel. I figured it was due to tracing a function that shouldn't be, so
I went through the following process to bisect to find the culprit:
cat /debug/tracing/available_filter_functions > t
num=`wc -l t`
sed -ne "1,${num}p" t > t1
let num=num+1
sed -ne "${num},$p" t > t2
cat t1 > /debug/tracing/set_ftrace_filter
echo function /debug/tracing/current_tracer
<failed? bisect t1, if not bisect t2>
It finally came down to this function: restore_interrupts()
I'm not sure why this locks up the system. It just seems to prevent
scheduling from occurring. Interrupts seem to still work, as I can ping
the box. But all user processes freeze.
When restore_interrupts() is not traced, function tracing works fine.
Cc: stable@kernel.org Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Thu, 7 Jun 2012 17:44:23 +0000 (17:44 +0000)]
powerpc: Fix Section mismatch warnings in prom_init.c
This patches tries to fix a couple of Section mismatch warnings like
following one:
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2923c): Section mismatch
in reference from the function .prom_query_opal() to the
function .init.text:.call_prom()
The function .prom_query_opal() references
the function __init .call_prom().
This is often because .prom_query_opal lacks a __init
annotation or the annotation of .call_prom is wrong.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Wed, 6 Jun 2012 20:56:43 +0000 (20:56 +0000)]
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
In entry_64.S version of ret_from_except_lite, you'll notice that
in the !preempt case, after we've checked MSR_PR we test for any
TIF flag in _TIF_USER_WORK_MASK to decide whether to go to do_work
or not. However, in the preempt case, we do a convoluted trick to
test SIGPENDING only if PR was set and always test NEED_RESCHED ...
but we forget to test any other bit of _TIF_USER_WORK_MASK !!! So
that means that with preempt, we completely fail to test for things
like single step, syscall tracing, etc...
This should be fixed as the following path:
- Test PR. If not set, go to resume_kernel, else continue.
- If go resume_kernel, to do that original do_work.
- If else, then always test for _TIF_USER_WORK_MASK to decide to do
that original user_work, else restore directly.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Tue, 19 Jun 2012 20:01:45 +0000 (20:01 +0000)]
powerpc: Fix uninitialised error in numa.c
chroma_defconfig currently gives me this with gcc 4.6:
arch/powerpc/mm/numa.c:638:13: error: 'dm' may be used uninitialized in this function [-Werror=uninitialized]
It's a bogus warning/error since of_get_drconf_memory() only writes it
anyway.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: <stable@kernel.org> [v3.3+] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 21 Jun 2012 17:50:27 +0000 (17:50 +0000)]
powerpc: Fix BPF_JIT code to link with multiple TOCs
If the kernel is big enough (eg. allyesconfig), the linker may need to
switch TOCs when calling from the BPF JIT code out to the external
helpers (skb_copy_bits() & bpf_internal_load_pointer_neg_helper()).
In order to do that we need to leave space after the bl for the linker
to insert a reload of our TOC pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Thu, 28 Jun 2012 19:38:51 +0000 (12:38 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon changes from Guenter Roeck:
"Just e-mail address updates"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Update my e-mail address
hwmon: (applesmc) correct email address for Jesper Juhl
Linus Torvalds [Thu, 28 Jun 2012 18:51:19 +0000 (11:51 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- the WDIOC_GETSTATUS return value
- the unregister of all NMI events on exit
- the loading of the iTCO_wdt driver after the conversion to the
lpc_ich mfd model."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: core: fix WDIOC_GETSTATUS return value
watchdog: hpwdt: Unregister NMI events on exit.
watchdog: iTCO_wdt: add platform driver module alias
Linus Torvalds [Thu, 28 Jun 2012 18:43:45 +0000 (11:43 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull UDF fixes from Jan Kara:
"Make UDF more robust in presence of corrupted filesystem"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fortify loading of sparing table
udf: Avoid run away loop when partition table length is corrupted
udf: Use 'ret' instead of abusing 'i' in udf_load_logicalvol()
Linus Torvalds [Thu, 28 Jun 2012 18:41:43 +0000 (11:41 -0700)]
Merge tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Artem Bityutskiy:
"Fix the debugfs regression - we never enable it because incorrect
'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
but we had 'IS_ENABLED(DEBUG_FS)'. Also fix incorrect assertion."
* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
UBI: correct usage of IS_ENABLED()
UBIFS: correct usage of IS_ENABLED()
UBIFS: fix assertion
Wim Van Sebroeck [Tue, 26 Jun 2012 18:07:21 +0000 (20:07 +0200)]
watchdog: core: fix WDIOC_GETSTATUS return value
In commit 7a87982420e5e126bfefeb42232d1fd92052794e we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Jan Beulich [Fri, 22 Jun 2012 15:41:00 +0000 (16:41 +0100)]
watchdog: iTCO_wdt: add platform driver module alias
The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: Aaron Sierra <asierra@xes-inc.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Thu, 28 Jun 2012 18:26:42 +0000 (11:26 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nearly all intel, one missing license header in nouveau, nothing
majorly earth shattering."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/nouveau: add license header to prime.
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.
2) Add device IDs for AR3011 and AR3012 bluetooth chips. From
Giancarlo Formicuccia and Marek Vasut.
3) Fix wireless regulatory deadlock, from Eliad Peller.
4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.
5) Revert the two commits that added skb_orphan_try(), it causes
erratic bonding behavior with UDP clients and the gains it used to
give are mostly no longer happening due to how BQL works. From Eric
Dumazet.
6) It took two tries, but Thomas Graf fixed a problem wherein we
registered ipv6 routing procfs files before their backend data were
initialized properly.
7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.
8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
Jason Wang.
9) Fix use of stale SKB data pointer after skb_linearize() call in
batman-adv, from Antonio Quartulli.
10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
Duyck.
11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
Mork.
12) Fix suspend/resume and open failure handling in usbnet from Ming
Lei.
13) Attempt to fix device r8169 hangs for certain chips, from Francois
Romieu.
14) Fix advancement of RX dirty pointer in some situations in sh_eth
driver, from Yoshihiro Shimoda.
15) Attempt to fix restart of IPV6 routing table dumps when there is an
intervening table update. From Eric Dumazet.
16) Respect security_inet_conn_request() return value in ipv6 TCP. From
Neal Cardwell.
17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.
18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
splats, from Eric Dumazet.
19) Make sure all bridge devices, regardless of whether they were
created via netlink or ioctls, have their rtnetlink ops hooked up.
From Thomas Graf and Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
9p: fix min_t() casting in p9pdu_vwritef()
can: flexcan: use be32_to_cpup to handle the value of dt entry
xen/netfront: teardown the device before unregistering it.
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
vhost: use USER_DS in vhost_worker thread
ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
net: l2tp_eth: use LLTX to avoid LOCKDEP splats
mac802154: add missed braces
net: l2tp_eth: fix l2tp_eth_dev_xmit race
net/mlx4_en: Release QP range in free_resources
net/mlx4: Use single completion vector after NOP failure
net/mlx4_en: Set correct port parameters during device initialization
ipheth: add support for iPad
caif-hsi: Add missing return in error path
caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
caif: Clear shutdown mask to zero at reconnect.
tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
ipv6: fib: fix fib dump restart
batman-adv: fix race condition in TT full-table replacement
batman-adv: only drop packets of known wifi clients
...
David S. Miller [Wed, 27 Jun 2012 22:27:24 +0000 (15:27 -0700)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
here's a patch intended for v3.5, targeting net/master. Hui Wang has
found and fixed an endianness problem in the device tree handling in
the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 26 Jun 2012 23:01:41 +0000 (23:01 +0000)]
9p: fix min_t() casting in p9pdu_vwritef()
I don't think we're actually likely to hit this limit but if we do
then the comparison should be done as size_t. The original code
is equivalent to:
len = strlen(sptr) % USHRT_MAX;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 27 Jun 2012 19:54:05 +0000 (12:54 -0700)]
Merge tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB gadget bugfixes, and a few new USB device ids
added to some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: CP210x Add 10 Device IDs
USB: option: Add USB ID for Novatel Ovation MC551
usb: phy: Fix Kconfig dependency for Phy drivers
usb-storage: revert commit afff07e61a52 (Add 090c:1000 to unusal-devs)
SCSI & usb-storage: add try_rc_10_first flag
usb: musb: host: release dma channels if no active io
usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
usb: otg: twl6030-usb: Fix twl writes
USB: option: add id for Cellient MEN-200
usb: dwc3: fix giveback of queued request in ep_dequeue
usb: gadget: Complete fsl qe/udc driver conversion
Linus Torvalds [Wed, 27 Jun 2012 19:50:28 +0000 (12:50 -0700)]
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here you find quite a few changes for HD-audio and a copule of quirk
additions for USB-audio. All reasonably small and/or trivial."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix power-map regression for HP dv6 & co
ALSA: hda - Initialize caches at codec reconfiguration
ALSA: hda - Fix memory leaks at module unload
ALSA: hda - Fix memory leaks in Realtek & Conexant codec parsers
ALSA: hda - Add Realtek ALC280 codec support
ALSA: hda - Remove obsoleted CONFIG_SND_HDA_ENABLE_REALTEK_QUIRKS
ASoC: wm8994: remove duplicate code
ALSA: usb-audio: add BOSS GT-100 support
ALSA: HDA: Add inverted internal mic quirk for Lenovo S205
ALSA: hda - Fix ALC272X codec detection
ALSA: snd_usb_audio: ignore ctrl errors on QuickCam Pro for Notebooks
ALSA: snd_usb_audio: ignore ctrl errors on QuickCam E3500
Linus Torvalds [Wed, 27 Jun 2012 19:48:07 +0000 (12:48 -0700)]
Merge tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- omap_hsmmc: Using AUTO_CMD12 (enabled by default in 3.5-rc1) has
been found to cause data corruption on the BeagleBoard, but no
other OMAP boards so far. Revert the patch until there's a root
cause explanation that makes sense, at which point we might
decide to use a blacklist or whitelist.
- mmc_block: Fix incorrect data timeouts for the case of multiblock
(ACMD22) writes for block-addressed cards.
* tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: omap_hsmmc: Enable Auto CMD12"
mmc: block: fix the data timeout issue with ACMD22
Linus Torvalds [Wed, 27 Jun 2012 19:44:58 +0000 (12:44 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clk common framework fixes from Mike Turquette:
"This contains three NULL pointer fixes and two device regression
fixups.
Two NULL pointer dereferences were in the common clk core due to lack
of sanity checking and the third NPD was in the mxs-specific clock
code due to incorrect use of __initdata.
The device regressions were the result of improper data: a wrong
string name for matching DT data broke the SPEAr ethernet controller
and another string matching problem in the mxs clock data resulted in
a broken MMC controller."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: fix clock lookup after freeing init memory
clk: mxs: fix ref_io clock definition
clk: Check parent for NULL in clk_change_rate
clk: Allow late cache allocation for clk->parents
clk: SPEAr600: Fix ethernet clock name for DT based probing
Dave Airlie [Wed, 27 Jun 2012 18:56:20 +0000 (19:56 +0100)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Two tiny patches and one revert:
- Kill a bogus error message introduced in 3.4, further Bspec reading
indicates that this is how the hw is supposed to work.
- Reorder one backlight register restore, fixing broken backlight on some
machines after resume.
- Revert a hack from Jesse for ivb backlight control - it breaks the
backlight controls on my shiny new ivb laptop."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
Deepthi Dharwar [Mon, 25 Jun 2012 21:59:54 +0000 (23:59 +0200)]
PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
Commit e978aa7d7d57d04eb5f88a7507c4fb98577def77 ( cpuidle: Move
dev->last_residency update to driver enter routine; remove dev->last_state)
was breaking suspend on laptops, as reported in the below link
- https://lkml.org/lkml/2011/11/11/164
This was fixed in commit 3439a8da16bcad6b0982ece938c9f8299bb53584
(ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
by removing acpi_idle_suspend flag.
- https://lkml.org/lkml/2011/11/14/74
But this did fix did not work on all systems
as Suspend/resume regression was reported on Lenovo S10-3
recently by Dave.
- https://lkml.org/lkml/2012/5/27/115
It looked like with commit e978aa7d broke suspend and
with commit 3439a8da resume was not working with acpi_idle driver.
This patch fixes the regression that caused this issue
in the first place. acpi_idle_suspend flag is essential on
some x86 systems to prevent the cpus from going to deeper C-states
when suspend is triggered ( commit b04e7bdb984 )
So reverting the commit 3439a8da is essential.
By default, irqs are disabled in cpu_idle arch specific call
and re-enabled in idle state return path . During suspend,
the acpi_idle_suspend flag is set, which
prevents the cpus from going to deeper idle states,
it is essential to enabling the irqs in this return path too.
To address the suspend issue,
we were not re-enabling the interrupts while returning from
acpi_idle_enter_bm() routine if acpi_idle_suspend flag is set.
and this caused suspend failure.
In addition to the above, to improve the readability of the code,
return of -ENIVAL is replaced with -EBUSY in acpi_idle_suspend
return path. Implying that the system is currently busy when suspend
is in progress, which prevents the cpus from entering deeper C-states.
Reported-and-Tested-by: Dav Hansen <dave@linux.vnet.ibm.com> Tested-by: Preeti Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Reviewed-by: Srivatsa S Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Jon Hunter [Mon, 25 Jun 2012 17:38:23 +0000 (12:38 -0500)]
ARM: OMAP4470: Fix OMAP4470 boot failure
OMAP4470 currently fails to boot, printing various messages such as ...
omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---
The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.
This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.
Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.
Cc: Paul Walmsley <paul@pwsan.com> Cc: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com>
Brian Norris [Mon, 18 Jun 2012 23:31:23 +0000 (16:31 -0700)]
UBI: correct usage of IS_ENABLED()
Commit "e9b4cf2 UBI: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Brian Norris [Mon, 18 Jun 2012 23:31:22 +0000 (16:31 -0700)]
UBIFS: correct usage of IS_ENABLED()
Commit "818039c UBIFS: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Hui Wang [Wed, 27 Jun 2012 08:19:18 +0000 (16:19 +0800)]
can: flexcan: use be32_to_cpup to handle the value of dt entry
The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.
Cc: stable <stable@vger.kernel.org> # v3.2+ Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Hui Wang <jason77.wang@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=675190
Reported-by: George Shuklin <george.shuklin@gmail.com> Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Tested-by: William Dauchy <wdauchy@gmail.com> Cc: stable@kernel.org Cc: 675190@bugs.debian.org Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
This ensures that bridges created with brctl(8) or ioctl(2) directly
also carry IFLA_LINKINFO when dumped over netlink. This also allows
to create a bridge with ioctl(2) and delete it with RTM_DELLINK.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jens Freimann [Tue, 26 Jun 2012 00:59:58 +0000 (00:59 +0000)]
vhost: use USER_DS in vhost_worker thread
On some architectures address spaces are set up in a way that this is
not necessary to work properly but on some others (like s390) it is.
Make sure we operate on the user address space to allow copy_xxx_user()
from the vhost_worker() thread by setting it explicitly before calling
use_mm() and revert it after unuse_mm().
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sachin Kamat [Wed, 27 Jun 2012 01:03:00 +0000 (10:03 +0900)]
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
Commit 20ef9e08 ("ARM: EXYNOS: Support DMA for EXYNOS5250 SoC")
renamed EXYNOS4_DEV_DMA to EXYNOS_DEV_DMA. But some machine entries
still had EXYNOS4_DEV_DMA. Changed them to EXYNOS_DEV_DMA.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>